1 /*- 2 * Copyright (c) 1997, Stefan Esser <se@freebsd.org> 3 * Copyright (c) 2000, Michael Smith <msmith@freebsd.org> 4 * Copyright (c) 2000, BSDi 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice unmodified, this list of conditions, and the following 12 * disclaimer. 13 * 2. Redistributions in binary form must reproduce the above copyright 14 * notice, this list of conditions and the following disclaimer in the 15 * documentation and/or other materials provided with the distribution. 16 * 17 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 18 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 19 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 20 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, 21 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 22 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 23 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 24 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 25 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF 26 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 27 */ 28 29 #include <sys/cdefs.h> 30 __FBSDID("$FreeBSD$"); 31 32 #include "opt_bus.h" 33 34 #include <sys/param.h> 35 #include <sys/systm.h> 36 #include <sys/malloc.h> 37 #include <sys/module.h> 38 #include <sys/linker.h> 39 #include <sys/fcntl.h> 40 #include <sys/conf.h> 41 #include <sys/kernel.h> 42 #include <sys/queue.h> 43 #include <sys/sysctl.h> 44 #include <sys/endian.h> 45 46 #include <vm/vm.h> 47 #include <vm/pmap.h> 48 #include <vm/vm_extern.h> 49 50 #include <sys/bus.h> 51 #include <machine/bus.h> 52 #include <sys/rman.h> 53 #include <machine/resource.h> 54 #include <machine/stdarg.h> 55 56 #if defined(__i386__) || defined(__amd64__) || defined(__powerpc__) 57 #include <machine/intr_machdep.h> 58 #endif 59 60 #include <sys/pciio.h> 61 #include <dev/pci/pcireg.h> 62 #include <dev/pci/pcivar.h> 63 #include <dev/pci/pci_private.h> 64 65 #include <dev/usb/controller/xhcireg.h> 66 #include <dev/usb/controller/ehcireg.h> 67 #include <dev/usb/controller/ohcireg.h> 68 #include <dev/usb/controller/uhcireg.h> 69 70 #include "pcib_if.h" 71 #include "pci_if.h" 72 73 #define PCIR_IS_BIOS(cfg, reg) \ 74 (((cfg)->hdrtype == PCIM_HDRTYPE_NORMAL && reg == PCIR_BIOS) || \ 75 ((cfg)->hdrtype == PCIM_HDRTYPE_BRIDGE && reg == PCIR_BIOS_1)) 76 77 static int pci_has_quirk(uint32_t devid, int quirk); 78 static pci_addr_t pci_mapbase(uint64_t mapreg); 79 static const char *pci_maptype(uint64_t mapreg); 80 static int pci_mapsize(uint64_t testval); 81 static int pci_maprange(uint64_t mapreg); 82 static pci_addr_t pci_rombase(uint64_t mapreg); 83 static int pci_romsize(uint64_t testval); 84 static void pci_fixancient(pcicfgregs *cfg); 85 static int pci_printf(pcicfgregs *cfg, const char *fmt, ...); 86 87 static int pci_porten(device_t dev); 88 static int pci_memen(device_t dev); 89 static void pci_assign_interrupt(device_t bus, device_t dev, 90 int force_route); 91 static int pci_add_map(device_t bus, device_t dev, int reg, 92 struct resource_list *rl, int force, int prefetch); 93 static int pci_probe(device_t dev); 94 static int pci_attach(device_t dev); 95 #ifdef PCI_RES_BUS 96 static int pci_detach(device_t dev); 97 #endif 98 static void pci_load_vendor_data(void); 99 static int pci_describe_parse_line(char **ptr, int *vendor, 100 int *device, char **desc); 101 static char *pci_describe_device(device_t dev); 102 static int pci_modevent(module_t mod, int what, void *arg); 103 static void pci_hdrtypedata(device_t pcib, int b, int s, int f, 104 pcicfgregs *cfg); 105 static void pci_read_cap(device_t pcib, pcicfgregs *cfg); 106 static int pci_read_vpd_reg(device_t pcib, pcicfgregs *cfg, 107 int reg, uint32_t *data); 108 #if 0 109 static int pci_write_vpd_reg(device_t pcib, pcicfgregs *cfg, 110 int reg, uint32_t data); 111 #endif 112 static void pci_read_vpd(device_t pcib, pcicfgregs *cfg); 113 static void pci_mask_msix(device_t dev, u_int index); 114 static void pci_unmask_msix(device_t dev, u_int index); 115 static int pci_msi_blacklisted(void); 116 static int pci_msix_blacklisted(void); 117 static void pci_resume_msi(device_t dev); 118 static void pci_resume_msix(device_t dev); 119 static int pci_remap_intr_method(device_t bus, device_t dev, 120 u_int irq); 121 122 static uint16_t pci_get_rid_method(device_t dev, device_t child); 123 124 static device_method_t pci_methods[] = { 125 /* Device interface */ 126 DEVMETHOD(device_probe, pci_probe), 127 DEVMETHOD(device_attach, pci_attach), 128 #ifdef PCI_RES_BUS 129 DEVMETHOD(device_detach, pci_detach), 130 #else 131 DEVMETHOD(device_detach, bus_generic_detach), 132 #endif 133 DEVMETHOD(device_shutdown, bus_generic_shutdown), 134 DEVMETHOD(device_suspend, bus_generic_suspend), 135 DEVMETHOD(device_resume, pci_resume), 136 137 /* Bus interface */ 138 DEVMETHOD(bus_print_child, pci_print_child), 139 DEVMETHOD(bus_probe_nomatch, pci_probe_nomatch), 140 DEVMETHOD(bus_read_ivar, pci_read_ivar), 141 DEVMETHOD(bus_write_ivar, pci_write_ivar), 142 DEVMETHOD(bus_driver_added, pci_driver_added), 143 DEVMETHOD(bus_setup_intr, pci_setup_intr), 144 DEVMETHOD(bus_teardown_intr, pci_teardown_intr), 145 146 DEVMETHOD(bus_get_dma_tag, pci_get_dma_tag), 147 DEVMETHOD(bus_get_resource_list,pci_get_resource_list), 148 DEVMETHOD(bus_set_resource, bus_generic_rl_set_resource), 149 DEVMETHOD(bus_get_resource, bus_generic_rl_get_resource), 150 DEVMETHOD(bus_delete_resource, pci_delete_resource), 151 DEVMETHOD(bus_alloc_resource, pci_alloc_resource), 152 DEVMETHOD(bus_adjust_resource, bus_generic_adjust_resource), 153 DEVMETHOD(bus_release_resource, pci_release_resource), 154 DEVMETHOD(bus_activate_resource, pci_activate_resource), 155 DEVMETHOD(bus_deactivate_resource, pci_deactivate_resource), 156 DEVMETHOD(bus_child_detached, pci_child_detached), 157 DEVMETHOD(bus_child_pnpinfo_str, pci_child_pnpinfo_str_method), 158 DEVMETHOD(bus_child_location_str, pci_child_location_str_method), 159 DEVMETHOD(bus_remap_intr, pci_remap_intr_method), 160 DEVMETHOD(bus_suspend_child, pci_suspend_child), 161 DEVMETHOD(bus_resume_child, pci_resume_child), 162 163 /* PCI interface */ 164 DEVMETHOD(pci_read_config, pci_read_config_method), 165 DEVMETHOD(pci_write_config, pci_write_config_method), 166 DEVMETHOD(pci_enable_busmaster, pci_enable_busmaster_method), 167 DEVMETHOD(pci_disable_busmaster, pci_disable_busmaster_method), 168 DEVMETHOD(pci_enable_io, pci_enable_io_method), 169 DEVMETHOD(pci_disable_io, pci_disable_io_method), 170 DEVMETHOD(pci_get_vpd_ident, pci_get_vpd_ident_method), 171 DEVMETHOD(pci_get_vpd_readonly, pci_get_vpd_readonly_method), 172 DEVMETHOD(pci_get_powerstate, pci_get_powerstate_method), 173 DEVMETHOD(pci_set_powerstate, pci_set_powerstate_method), 174 DEVMETHOD(pci_assign_interrupt, pci_assign_interrupt_method), 175 DEVMETHOD(pci_find_cap, pci_find_cap_method), 176 DEVMETHOD(pci_find_extcap, pci_find_extcap_method), 177 DEVMETHOD(pci_find_htcap, pci_find_htcap_method), 178 DEVMETHOD(pci_alloc_msi, pci_alloc_msi_method), 179 DEVMETHOD(pci_alloc_msix, pci_alloc_msix_method), 180 DEVMETHOD(pci_enable_msi, pci_enable_msi_method), 181 DEVMETHOD(pci_enable_msix, pci_enable_msix_method), 182 DEVMETHOD(pci_disable_msi, pci_disable_msi_method), 183 DEVMETHOD(pci_remap_msix, pci_remap_msix_method), 184 DEVMETHOD(pci_release_msi, pci_release_msi_method), 185 DEVMETHOD(pci_msi_count, pci_msi_count_method), 186 DEVMETHOD(pci_msix_count, pci_msix_count_method), 187 DEVMETHOD(pci_get_rid, pci_get_rid_method), 188 DEVMETHOD(pci_child_added, pci_child_added_method), 189 190 DEVMETHOD_END 191 }; 192 193 DEFINE_CLASS_0(pci, pci_driver, pci_methods, sizeof(struct pci_softc)); 194 195 static devclass_t pci_devclass; 196 DRIVER_MODULE(pci, pcib, pci_driver, pci_devclass, pci_modevent, NULL); 197 MODULE_VERSION(pci, 1); 198 199 static char *pci_vendordata; 200 static size_t pci_vendordata_size; 201 202 struct pci_quirk { 203 uint32_t devid; /* Vendor/device of the card */ 204 int type; 205 #define PCI_QUIRK_MAP_REG 1 /* PCI map register in weird place */ 206 #define PCI_QUIRK_DISABLE_MSI 2 /* Neither MSI nor MSI-X work */ 207 #define PCI_QUIRK_ENABLE_MSI_VM 3 /* Older chipset in VM where MSI works */ 208 #define PCI_QUIRK_UNMAP_REG 4 /* Ignore PCI map register */ 209 #define PCI_QUIRK_DISABLE_MSIX 5 /* MSI-X doesn't work */ 210 #define PCI_QUIRK_MSI_INTX_BUG 6 /* PCIM_CMD_INTxDIS disables MSI */ 211 int arg1; 212 int arg2; 213 }; 214 215 static const struct pci_quirk pci_quirks[] = { 216 /* The Intel 82371AB and 82443MX have a map register at offset 0x90. */ 217 { 0x71138086, PCI_QUIRK_MAP_REG, 0x90, 0 }, 218 { 0x719b8086, PCI_QUIRK_MAP_REG, 0x90, 0 }, 219 /* As does the Serverworks OSB4 (the SMBus mapping register) */ 220 { 0x02001166, PCI_QUIRK_MAP_REG, 0x90, 0 }, 221 222 /* 223 * MSI doesn't work with the ServerWorks CNB20-HE Host Bridge 224 * or the CMIC-SL (AKA ServerWorks GC_LE). 225 */ 226 { 0x00141166, PCI_QUIRK_DISABLE_MSI, 0, 0 }, 227 { 0x00171166, PCI_QUIRK_DISABLE_MSI, 0, 0 }, 228 229 /* 230 * MSI doesn't work on earlier Intel chipsets including 231 * E7500, E7501, E7505, 845, 865, 875/E7210, and 855. 232 */ 233 { 0x25408086, PCI_QUIRK_DISABLE_MSI, 0, 0 }, 234 { 0x254c8086, PCI_QUIRK_DISABLE_MSI, 0, 0 }, 235 { 0x25508086, PCI_QUIRK_DISABLE_MSI, 0, 0 }, 236 { 0x25608086, PCI_QUIRK_DISABLE_MSI, 0, 0 }, 237 { 0x25708086, PCI_QUIRK_DISABLE_MSI, 0, 0 }, 238 { 0x25788086, PCI_QUIRK_DISABLE_MSI, 0, 0 }, 239 { 0x35808086, PCI_QUIRK_DISABLE_MSI, 0, 0 }, 240 241 /* 242 * MSI doesn't work with devices behind the AMD 8131 HT-PCIX 243 * bridge. 244 */ 245 { 0x74501022, PCI_QUIRK_DISABLE_MSI, 0, 0 }, 246 247 /* 248 * MSI-X allocation doesn't work properly for devices passed through 249 * by VMware up to at least ESXi 5.1. 250 */ 251 { 0x079015ad, PCI_QUIRK_DISABLE_MSIX, 0, 0 }, /* PCI/PCI-X */ 252 { 0x07a015ad, PCI_QUIRK_DISABLE_MSIX, 0, 0 }, /* PCIe */ 253 254 /* 255 * Some virtualization environments emulate an older chipset 256 * but support MSI just fine. QEMU uses the Intel 82440. 257 */ 258 { 0x12378086, PCI_QUIRK_ENABLE_MSI_VM, 0, 0 }, 259 260 /* 261 * HPET MMIO base address may appear in Bar1 for AMD SB600 SMBus 262 * controller depending on SoftPciRst register (PM_IO 0x55 [7]). 263 * It prevents us from attaching hpet(4) when the bit is unset. 264 * Note this quirk only affects SB600 revision A13 and earlier. 265 * For SB600 A21 and later, firmware must set the bit to hide it. 266 * For SB700 and later, it is unused and hardcoded to zero. 267 */ 268 { 0x43851002, PCI_QUIRK_UNMAP_REG, 0x14, 0 }, 269 270 /* 271 * Atheros AR8161/AR8162/E2200 ethernet controller has a bug that 272 * MSI interrupt does not assert if PCIM_CMD_INTxDIS bit of the 273 * command register is set. 274 */ 275 { 0x10911969, PCI_QUIRK_MSI_INTX_BUG, 0, 0 }, 276 { 0xE0911969, PCI_QUIRK_MSI_INTX_BUG, 0, 0 }, 277 { 0x10901969, PCI_QUIRK_MSI_INTX_BUG, 0, 0 }, 278 279 { 0 } 280 }; 281 282 /* map register information */ 283 #define PCI_MAPMEM 0x01 /* memory map */ 284 #define PCI_MAPMEMP 0x02 /* prefetchable memory map */ 285 #define PCI_MAPPORT 0x04 /* port map */ 286 287 struct devlist pci_devq; 288 uint32_t pci_generation; 289 uint32_t pci_numdevs = 0; 290 static int pcie_chipset, pcix_chipset; 291 292 /* sysctl vars */ 293 SYSCTL_NODE(_hw, OID_AUTO, pci, CTLFLAG_RD, 0, "PCI bus tuning parameters"); 294 295 static int pci_enable_io_modes = 1; 296 SYSCTL_INT(_hw_pci, OID_AUTO, enable_io_modes, CTLFLAG_RWTUN, 297 &pci_enable_io_modes, 1, 298 "Enable I/O and memory bits in the config register. Some BIOSes do not\n\ 299 enable these bits correctly. We'd like to do this all the time, but there\n\ 300 are some peripherals that this causes problems with."); 301 302 static int pci_do_realloc_bars = 0; 303 SYSCTL_INT(_hw_pci, OID_AUTO, realloc_bars, CTLFLAG_RWTUN, 304 &pci_do_realloc_bars, 0, 305 "Attempt to allocate a new range for any BARs whose original " 306 "firmware-assigned ranges fail to allocate during the initial device scan."); 307 308 static int pci_do_power_nodriver = 0; 309 SYSCTL_INT(_hw_pci, OID_AUTO, do_power_nodriver, CTLFLAG_RWTUN, 310 &pci_do_power_nodriver, 0, 311 "Place a function into D3 state when no driver attaches to it. 0 means\n\ 312 disable. 1 means conservatively place devices into D3 state. 2 means\n\ 313 agressively place devices into D3 state. 3 means put absolutely everything\n\ 314 in D3 state."); 315 316 int pci_do_power_resume = 1; 317 SYSCTL_INT(_hw_pci, OID_AUTO, do_power_resume, CTLFLAG_RWTUN, 318 &pci_do_power_resume, 1, 319 "Transition from D3 -> D0 on resume."); 320 321 int pci_do_power_suspend = 1; 322 SYSCTL_INT(_hw_pci, OID_AUTO, do_power_suspend, CTLFLAG_RWTUN, 323 &pci_do_power_suspend, 1, 324 "Transition from D0 -> D3 on suspend."); 325 326 static int pci_do_msi = 1; 327 SYSCTL_INT(_hw_pci, OID_AUTO, enable_msi, CTLFLAG_RWTUN, &pci_do_msi, 1, 328 "Enable support for MSI interrupts"); 329 330 static int pci_do_msix = 1; 331 SYSCTL_INT(_hw_pci, OID_AUTO, enable_msix, CTLFLAG_RWTUN, &pci_do_msix, 1, 332 "Enable support for MSI-X interrupts"); 333 334 static int pci_honor_msi_blacklist = 1; 335 SYSCTL_INT(_hw_pci, OID_AUTO, honor_msi_blacklist, CTLFLAG_RDTUN, 336 &pci_honor_msi_blacklist, 1, "Honor chipset blacklist for MSI/MSI-X"); 337 338 #if defined(__i386__) || defined(__amd64__) 339 static int pci_usb_takeover = 1; 340 #else 341 static int pci_usb_takeover = 0; 342 #endif 343 SYSCTL_INT(_hw_pci, OID_AUTO, usb_early_takeover, CTLFLAG_RDTUN, 344 &pci_usb_takeover, 1, "Enable early takeover of USB controllers.\n\ 345 Disable this if you depend on BIOS emulation of USB devices, that is\n\ 346 you use USB devices (like keyboard or mouse) but do not load USB drivers"); 347 348 static int pci_clear_bars; 349 SYSCTL_INT(_hw_pci, OID_AUTO, clear_bars, CTLFLAG_RDTUN, &pci_clear_bars, 0, 350 "Ignore firmware-assigned resources for BARs."); 351 352 #if defined(NEW_PCIB) && defined(PCI_RES_BUS) 353 static int pci_clear_buses; 354 SYSCTL_INT(_hw_pci, OID_AUTO, clear_buses, CTLFLAG_RDTUN, &pci_clear_buses, 0, 355 "Ignore firmware-assigned bus numbers."); 356 #endif 357 358 static int pci_enable_ari = 1; 359 SYSCTL_INT(_hw_pci, OID_AUTO, enable_ari, CTLFLAG_RDTUN, &pci_enable_ari, 360 0, "Enable support for PCIe Alternative RID Interpretation"); 361 362 static int 363 pci_has_quirk(uint32_t devid, int quirk) 364 { 365 const struct pci_quirk *q; 366 367 for (q = &pci_quirks[0]; q->devid; q++) { 368 if (q->devid == devid && q->type == quirk) 369 return (1); 370 } 371 return (0); 372 } 373 374 /* Find a device_t by bus/slot/function in domain 0 */ 375 376 device_t 377 pci_find_bsf(uint8_t bus, uint8_t slot, uint8_t func) 378 { 379 380 return (pci_find_dbsf(0, bus, slot, func)); 381 } 382 383 /* Find a device_t by domain/bus/slot/function */ 384 385 device_t 386 pci_find_dbsf(uint32_t domain, uint8_t bus, uint8_t slot, uint8_t func) 387 { 388 struct pci_devinfo *dinfo; 389 390 STAILQ_FOREACH(dinfo, &pci_devq, pci_links) { 391 if ((dinfo->cfg.domain == domain) && 392 (dinfo->cfg.bus == bus) && 393 (dinfo->cfg.slot == slot) && 394 (dinfo->cfg.func == func)) { 395 return (dinfo->cfg.dev); 396 } 397 } 398 399 return (NULL); 400 } 401 402 /* Find a device_t by vendor/device ID */ 403 404 device_t 405 pci_find_device(uint16_t vendor, uint16_t device) 406 { 407 struct pci_devinfo *dinfo; 408 409 STAILQ_FOREACH(dinfo, &pci_devq, pci_links) { 410 if ((dinfo->cfg.vendor == vendor) && 411 (dinfo->cfg.device == device)) { 412 return (dinfo->cfg.dev); 413 } 414 } 415 416 return (NULL); 417 } 418 419 device_t 420 pci_find_class(uint8_t class, uint8_t subclass) 421 { 422 struct pci_devinfo *dinfo; 423 424 STAILQ_FOREACH(dinfo, &pci_devq, pci_links) { 425 if (dinfo->cfg.baseclass == class && 426 dinfo->cfg.subclass == subclass) { 427 return (dinfo->cfg.dev); 428 } 429 } 430 431 return (NULL); 432 } 433 434 static int 435 pci_printf(pcicfgregs *cfg, const char *fmt, ...) 436 { 437 va_list ap; 438 int retval; 439 440 retval = printf("pci%d:%d:%d:%d: ", cfg->domain, cfg->bus, cfg->slot, 441 cfg->func); 442 va_start(ap, fmt); 443 retval += vprintf(fmt, ap); 444 va_end(ap); 445 return (retval); 446 } 447 448 /* return base address of memory or port map */ 449 450 static pci_addr_t 451 pci_mapbase(uint64_t mapreg) 452 { 453 454 if (PCI_BAR_MEM(mapreg)) 455 return (mapreg & PCIM_BAR_MEM_BASE); 456 else 457 return (mapreg & PCIM_BAR_IO_BASE); 458 } 459 460 /* return map type of memory or port map */ 461 462 static const char * 463 pci_maptype(uint64_t mapreg) 464 { 465 466 if (PCI_BAR_IO(mapreg)) 467 return ("I/O Port"); 468 if (mapreg & PCIM_BAR_MEM_PREFETCH) 469 return ("Prefetchable Memory"); 470 return ("Memory"); 471 } 472 473 /* return log2 of map size decoded for memory or port map */ 474 475 static int 476 pci_mapsize(uint64_t testval) 477 { 478 int ln2size; 479 480 testval = pci_mapbase(testval); 481 ln2size = 0; 482 if (testval != 0) { 483 while ((testval & 1) == 0) 484 { 485 ln2size++; 486 testval >>= 1; 487 } 488 } 489 return (ln2size); 490 } 491 492 /* return base address of device ROM */ 493 494 static pci_addr_t 495 pci_rombase(uint64_t mapreg) 496 { 497 498 return (mapreg & PCIM_BIOS_ADDR_MASK); 499 } 500 501 /* return log2 of map size decided for device ROM */ 502 503 static int 504 pci_romsize(uint64_t testval) 505 { 506 int ln2size; 507 508 testval = pci_rombase(testval); 509 ln2size = 0; 510 if (testval != 0) { 511 while ((testval & 1) == 0) 512 { 513 ln2size++; 514 testval >>= 1; 515 } 516 } 517 return (ln2size); 518 } 519 520 /* return log2 of address range supported by map register */ 521 522 static int 523 pci_maprange(uint64_t mapreg) 524 { 525 int ln2range = 0; 526 527 if (PCI_BAR_IO(mapreg)) 528 ln2range = 32; 529 else 530 switch (mapreg & PCIM_BAR_MEM_TYPE) { 531 case PCIM_BAR_MEM_32: 532 ln2range = 32; 533 break; 534 case PCIM_BAR_MEM_1MB: 535 ln2range = 20; 536 break; 537 case PCIM_BAR_MEM_64: 538 ln2range = 64; 539 break; 540 } 541 return (ln2range); 542 } 543 544 /* adjust some values from PCI 1.0 devices to match 2.0 standards ... */ 545 546 static void 547 pci_fixancient(pcicfgregs *cfg) 548 { 549 if ((cfg->hdrtype & PCIM_HDRTYPE) != PCIM_HDRTYPE_NORMAL) 550 return; 551 552 /* PCI to PCI bridges use header type 1 */ 553 if (cfg->baseclass == PCIC_BRIDGE && cfg->subclass == PCIS_BRIDGE_PCI) 554 cfg->hdrtype = PCIM_HDRTYPE_BRIDGE; 555 } 556 557 /* extract header type specific config data */ 558 559 static void 560 pci_hdrtypedata(device_t pcib, int b, int s, int f, pcicfgregs *cfg) 561 { 562 #define REG(n, w) PCIB_READ_CONFIG(pcib, b, s, f, n, w) 563 switch (cfg->hdrtype & PCIM_HDRTYPE) { 564 case PCIM_HDRTYPE_NORMAL: 565 cfg->subvendor = REG(PCIR_SUBVEND_0, 2); 566 cfg->subdevice = REG(PCIR_SUBDEV_0, 2); 567 cfg->nummaps = PCI_MAXMAPS_0; 568 break; 569 case PCIM_HDRTYPE_BRIDGE: 570 cfg->nummaps = PCI_MAXMAPS_1; 571 break; 572 case PCIM_HDRTYPE_CARDBUS: 573 cfg->subvendor = REG(PCIR_SUBVEND_2, 2); 574 cfg->subdevice = REG(PCIR_SUBDEV_2, 2); 575 cfg->nummaps = PCI_MAXMAPS_2; 576 break; 577 } 578 #undef REG 579 } 580 581 /* read configuration header into pcicfgregs structure */ 582 struct pci_devinfo * 583 pci_read_device(device_t pcib, int d, int b, int s, int f, size_t size) 584 { 585 #define REG(n, w) PCIB_READ_CONFIG(pcib, b, s, f, n, w) 586 pcicfgregs *cfg = NULL; 587 struct pci_devinfo *devlist_entry; 588 struct devlist *devlist_head; 589 590 devlist_head = &pci_devq; 591 592 devlist_entry = NULL; 593 594 if (REG(PCIR_DEVVENDOR, 4) != 0xfffffffful) { 595 devlist_entry = malloc(size, M_DEVBUF, M_WAITOK | M_ZERO); 596 if (devlist_entry == NULL) 597 return (NULL); 598 599 cfg = &devlist_entry->cfg; 600 601 cfg->domain = d; 602 cfg->bus = b; 603 cfg->slot = s; 604 cfg->func = f; 605 cfg->vendor = REG(PCIR_VENDOR, 2); 606 cfg->device = REG(PCIR_DEVICE, 2); 607 cfg->cmdreg = REG(PCIR_COMMAND, 2); 608 cfg->statreg = REG(PCIR_STATUS, 2); 609 cfg->baseclass = REG(PCIR_CLASS, 1); 610 cfg->subclass = REG(PCIR_SUBCLASS, 1); 611 cfg->progif = REG(PCIR_PROGIF, 1); 612 cfg->revid = REG(PCIR_REVID, 1); 613 cfg->hdrtype = REG(PCIR_HDRTYPE, 1); 614 cfg->cachelnsz = REG(PCIR_CACHELNSZ, 1); 615 cfg->lattimer = REG(PCIR_LATTIMER, 1); 616 cfg->intpin = REG(PCIR_INTPIN, 1); 617 cfg->intline = REG(PCIR_INTLINE, 1); 618 619 cfg->mingnt = REG(PCIR_MINGNT, 1); 620 cfg->maxlat = REG(PCIR_MAXLAT, 1); 621 622 cfg->mfdev = (cfg->hdrtype & PCIM_MFDEV) != 0; 623 cfg->hdrtype &= ~PCIM_MFDEV; 624 STAILQ_INIT(&cfg->maps); 625 626 pci_fixancient(cfg); 627 pci_hdrtypedata(pcib, b, s, f, cfg); 628 629 if (REG(PCIR_STATUS, 2) & PCIM_STATUS_CAPPRESENT) 630 pci_read_cap(pcib, cfg); 631 632 STAILQ_INSERT_TAIL(devlist_head, devlist_entry, pci_links); 633 634 devlist_entry->conf.pc_sel.pc_domain = cfg->domain; 635 devlist_entry->conf.pc_sel.pc_bus = cfg->bus; 636 devlist_entry->conf.pc_sel.pc_dev = cfg->slot; 637 devlist_entry->conf.pc_sel.pc_func = cfg->func; 638 devlist_entry->conf.pc_hdr = cfg->hdrtype; 639 640 devlist_entry->conf.pc_subvendor = cfg->subvendor; 641 devlist_entry->conf.pc_subdevice = cfg->subdevice; 642 devlist_entry->conf.pc_vendor = cfg->vendor; 643 devlist_entry->conf.pc_device = cfg->device; 644 645 devlist_entry->conf.pc_class = cfg->baseclass; 646 devlist_entry->conf.pc_subclass = cfg->subclass; 647 devlist_entry->conf.pc_progif = cfg->progif; 648 devlist_entry->conf.pc_revid = cfg->revid; 649 650 pci_numdevs++; 651 pci_generation++; 652 } 653 return (devlist_entry); 654 #undef REG 655 } 656 657 static void 658 pci_read_cap(device_t pcib, pcicfgregs *cfg) 659 { 660 #define REG(n, w) PCIB_READ_CONFIG(pcib, cfg->bus, cfg->slot, cfg->func, n, w) 661 #define WREG(n, v, w) PCIB_WRITE_CONFIG(pcib, cfg->bus, cfg->slot, cfg->func, n, v, w) 662 #if defined(__i386__) || defined(__amd64__) || defined(__powerpc__) 663 uint64_t addr; 664 #endif 665 uint32_t val; 666 int ptr, nextptr, ptrptr; 667 668 switch (cfg->hdrtype & PCIM_HDRTYPE) { 669 case PCIM_HDRTYPE_NORMAL: 670 case PCIM_HDRTYPE_BRIDGE: 671 ptrptr = PCIR_CAP_PTR; 672 break; 673 case PCIM_HDRTYPE_CARDBUS: 674 ptrptr = PCIR_CAP_PTR_2; /* cardbus capabilities ptr */ 675 break; 676 default: 677 return; /* no extended capabilities support */ 678 } 679 nextptr = REG(ptrptr, 1); /* sanity check? */ 680 681 /* 682 * Read capability entries. 683 */ 684 while (nextptr != 0) { 685 /* Sanity check */ 686 if (nextptr > 255) { 687 printf("illegal PCI extended capability offset %d\n", 688 nextptr); 689 return; 690 } 691 /* Find the next entry */ 692 ptr = nextptr; 693 nextptr = REG(ptr + PCICAP_NEXTPTR, 1); 694 695 /* Process this entry */ 696 switch (REG(ptr + PCICAP_ID, 1)) { 697 case PCIY_PMG: /* PCI power management */ 698 if (cfg->pp.pp_cap == 0) { 699 cfg->pp.pp_cap = REG(ptr + PCIR_POWER_CAP, 2); 700 cfg->pp.pp_status = ptr + PCIR_POWER_STATUS; 701 cfg->pp.pp_bse = ptr + PCIR_POWER_BSE; 702 if ((nextptr - ptr) > PCIR_POWER_DATA) 703 cfg->pp.pp_data = ptr + PCIR_POWER_DATA; 704 } 705 break; 706 case PCIY_HT: /* HyperTransport */ 707 /* Determine HT-specific capability type. */ 708 val = REG(ptr + PCIR_HT_COMMAND, 2); 709 710 if ((val & 0xe000) == PCIM_HTCAP_SLAVE) 711 cfg->ht.ht_slave = ptr; 712 713 #if defined(__i386__) || defined(__amd64__) || defined(__powerpc__) 714 switch (val & PCIM_HTCMD_CAP_MASK) { 715 case PCIM_HTCAP_MSI_MAPPING: 716 if (!(val & PCIM_HTCMD_MSI_FIXED)) { 717 /* Sanity check the mapping window. */ 718 addr = REG(ptr + PCIR_HTMSI_ADDRESS_HI, 719 4); 720 addr <<= 32; 721 addr |= REG(ptr + PCIR_HTMSI_ADDRESS_LO, 722 4); 723 if (addr != MSI_INTEL_ADDR_BASE) 724 device_printf(pcib, 725 "HT device at pci%d:%d:%d:%d has non-default MSI window 0x%llx\n", 726 cfg->domain, cfg->bus, 727 cfg->slot, cfg->func, 728 (long long)addr); 729 } else 730 addr = MSI_INTEL_ADDR_BASE; 731 732 cfg->ht.ht_msimap = ptr; 733 cfg->ht.ht_msictrl = val; 734 cfg->ht.ht_msiaddr = addr; 735 break; 736 } 737 #endif 738 break; 739 case PCIY_MSI: /* PCI MSI */ 740 cfg->msi.msi_location = ptr; 741 cfg->msi.msi_ctrl = REG(ptr + PCIR_MSI_CTRL, 2); 742 cfg->msi.msi_msgnum = 1 << ((cfg->msi.msi_ctrl & 743 PCIM_MSICTRL_MMC_MASK)>>1); 744 break; 745 case PCIY_MSIX: /* PCI MSI-X */ 746 cfg->msix.msix_location = ptr; 747 cfg->msix.msix_ctrl = REG(ptr + PCIR_MSIX_CTRL, 2); 748 cfg->msix.msix_msgnum = (cfg->msix.msix_ctrl & 749 PCIM_MSIXCTRL_TABLE_SIZE) + 1; 750 val = REG(ptr + PCIR_MSIX_TABLE, 4); 751 cfg->msix.msix_table_bar = PCIR_BAR(val & 752 PCIM_MSIX_BIR_MASK); 753 cfg->msix.msix_table_offset = val & ~PCIM_MSIX_BIR_MASK; 754 val = REG(ptr + PCIR_MSIX_PBA, 4); 755 cfg->msix.msix_pba_bar = PCIR_BAR(val & 756 PCIM_MSIX_BIR_MASK); 757 cfg->msix.msix_pba_offset = val & ~PCIM_MSIX_BIR_MASK; 758 break; 759 case PCIY_VPD: /* PCI Vital Product Data */ 760 cfg->vpd.vpd_reg = ptr; 761 break; 762 case PCIY_SUBVENDOR: 763 /* Should always be true. */ 764 if ((cfg->hdrtype & PCIM_HDRTYPE) == 765 PCIM_HDRTYPE_BRIDGE) { 766 val = REG(ptr + PCIR_SUBVENDCAP_ID, 4); 767 cfg->subvendor = val & 0xffff; 768 cfg->subdevice = val >> 16; 769 } 770 break; 771 case PCIY_PCIX: /* PCI-X */ 772 /* 773 * Assume we have a PCI-X chipset if we have 774 * at least one PCI-PCI bridge with a PCI-X 775 * capability. Note that some systems with 776 * PCI-express or HT chipsets might match on 777 * this check as well. 778 */ 779 if ((cfg->hdrtype & PCIM_HDRTYPE) == 780 PCIM_HDRTYPE_BRIDGE) 781 pcix_chipset = 1; 782 cfg->pcix.pcix_location = ptr; 783 break; 784 case PCIY_EXPRESS: /* PCI-express */ 785 /* 786 * Assume we have a PCI-express chipset if we have 787 * at least one PCI-express device. 788 */ 789 pcie_chipset = 1; 790 cfg->pcie.pcie_location = ptr; 791 val = REG(ptr + PCIER_FLAGS, 2); 792 cfg->pcie.pcie_type = val & PCIEM_FLAGS_TYPE; 793 break; 794 default: 795 break; 796 } 797 } 798 799 #if defined(__powerpc__) 800 /* 801 * Enable the MSI mapping window for all HyperTransport 802 * slaves. PCI-PCI bridges have their windows enabled via 803 * PCIB_MAP_MSI(). 804 */ 805 if (cfg->ht.ht_slave != 0 && cfg->ht.ht_msimap != 0 && 806 !(cfg->ht.ht_msictrl & PCIM_HTCMD_MSI_ENABLE)) { 807 device_printf(pcib, 808 "Enabling MSI window for HyperTransport slave at pci%d:%d:%d:%d\n", 809 cfg->domain, cfg->bus, cfg->slot, cfg->func); 810 cfg->ht.ht_msictrl |= PCIM_HTCMD_MSI_ENABLE; 811 WREG(cfg->ht.ht_msimap + PCIR_HT_COMMAND, cfg->ht.ht_msictrl, 812 2); 813 } 814 #endif 815 /* REG and WREG use carry through to next functions */ 816 } 817 818 /* 819 * PCI Vital Product Data 820 */ 821 822 #define PCI_VPD_TIMEOUT 1000000 823 824 static int 825 pci_read_vpd_reg(device_t pcib, pcicfgregs *cfg, int reg, uint32_t *data) 826 { 827 int count = PCI_VPD_TIMEOUT; 828 829 KASSERT((reg & 3) == 0, ("VPD register must by 4 byte aligned")); 830 831 WREG(cfg->vpd.vpd_reg + PCIR_VPD_ADDR, reg, 2); 832 833 while ((REG(cfg->vpd.vpd_reg + PCIR_VPD_ADDR, 2) & 0x8000) != 0x8000) { 834 if (--count < 0) 835 return (ENXIO); 836 DELAY(1); /* limit looping */ 837 } 838 *data = (REG(cfg->vpd.vpd_reg + PCIR_VPD_DATA, 4)); 839 840 return (0); 841 } 842 843 #if 0 844 static int 845 pci_write_vpd_reg(device_t pcib, pcicfgregs *cfg, int reg, uint32_t data) 846 { 847 int count = PCI_VPD_TIMEOUT; 848 849 KASSERT((reg & 3) == 0, ("VPD register must by 4 byte aligned")); 850 851 WREG(cfg->vpd.vpd_reg + PCIR_VPD_DATA, data, 4); 852 WREG(cfg->vpd.vpd_reg + PCIR_VPD_ADDR, reg | 0x8000, 2); 853 while ((REG(cfg->vpd.vpd_reg + PCIR_VPD_ADDR, 2) & 0x8000) == 0x8000) { 854 if (--count < 0) 855 return (ENXIO); 856 DELAY(1); /* limit looping */ 857 } 858 859 return (0); 860 } 861 #endif 862 863 #undef PCI_VPD_TIMEOUT 864 865 struct vpd_readstate { 866 device_t pcib; 867 pcicfgregs *cfg; 868 uint32_t val; 869 int bytesinval; 870 int off; 871 uint8_t cksum; 872 }; 873 874 static int 875 vpd_nextbyte(struct vpd_readstate *vrs, uint8_t *data) 876 { 877 uint32_t reg; 878 uint8_t byte; 879 880 if (vrs->bytesinval == 0) { 881 if (pci_read_vpd_reg(vrs->pcib, vrs->cfg, vrs->off, ®)) 882 return (ENXIO); 883 vrs->val = le32toh(reg); 884 vrs->off += 4; 885 byte = vrs->val & 0xff; 886 vrs->bytesinval = 3; 887 } else { 888 vrs->val = vrs->val >> 8; 889 byte = vrs->val & 0xff; 890 vrs->bytesinval--; 891 } 892 893 vrs->cksum += byte; 894 *data = byte; 895 return (0); 896 } 897 898 static void 899 pci_read_vpd(device_t pcib, pcicfgregs *cfg) 900 { 901 struct vpd_readstate vrs; 902 int state; 903 int name; 904 int remain; 905 int i; 906 int alloc, off; /* alloc/off for RO/W arrays */ 907 int cksumvalid; 908 int dflen; 909 uint8_t byte; 910 uint8_t byte2; 911 912 /* init vpd reader */ 913 vrs.bytesinval = 0; 914 vrs.off = 0; 915 vrs.pcib = pcib; 916 vrs.cfg = cfg; 917 vrs.cksum = 0; 918 919 state = 0; 920 name = remain = i = 0; /* shut up stupid gcc */ 921 alloc = off = 0; /* shut up stupid gcc */ 922 dflen = 0; /* shut up stupid gcc */ 923 cksumvalid = -1; 924 while (state >= 0) { 925 if (vpd_nextbyte(&vrs, &byte)) { 926 state = -2; 927 break; 928 } 929 #if 0 930 printf("vpd: val: %#x, off: %d, bytesinval: %d, byte: %#hhx, " \ 931 "state: %d, remain: %d, name: %#x, i: %d\n", vrs.val, 932 vrs.off, vrs.bytesinval, byte, state, remain, name, i); 933 #endif 934 switch (state) { 935 case 0: /* item name */ 936 if (byte & 0x80) { 937 if (vpd_nextbyte(&vrs, &byte2)) { 938 state = -2; 939 break; 940 } 941 remain = byte2; 942 if (vpd_nextbyte(&vrs, &byte2)) { 943 state = -2; 944 break; 945 } 946 remain |= byte2 << 8; 947 if (remain > (0x7f*4 - vrs.off)) { 948 state = -1; 949 pci_printf(cfg, 950 "invalid VPD data, remain %#x\n", 951 remain); 952 } 953 name = byte & 0x7f; 954 } else { 955 remain = byte & 0x7; 956 name = (byte >> 3) & 0xf; 957 } 958 switch (name) { 959 case 0x2: /* String */ 960 cfg->vpd.vpd_ident = malloc(remain + 1, 961 M_DEVBUF, M_WAITOK); 962 i = 0; 963 state = 1; 964 break; 965 case 0xf: /* End */ 966 state = -1; 967 break; 968 case 0x10: /* VPD-R */ 969 alloc = 8; 970 off = 0; 971 cfg->vpd.vpd_ros = malloc(alloc * 972 sizeof(*cfg->vpd.vpd_ros), M_DEVBUF, 973 M_WAITOK | M_ZERO); 974 state = 2; 975 break; 976 case 0x11: /* VPD-W */ 977 alloc = 8; 978 off = 0; 979 cfg->vpd.vpd_w = malloc(alloc * 980 sizeof(*cfg->vpd.vpd_w), M_DEVBUF, 981 M_WAITOK | M_ZERO); 982 state = 5; 983 break; 984 default: /* Invalid data, abort */ 985 state = -1; 986 break; 987 } 988 break; 989 990 case 1: /* Identifier String */ 991 cfg->vpd.vpd_ident[i++] = byte; 992 remain--; 993 if (remain == 0) { 994 cfg->vpd.vpd_ident[i] = '\0'; 995 state = 0; 996 } 997 break; 998 999 case 2: /* VPD-R Keyword Header */ 1000 if (off == alloc) { 1001 cfg->vpd.vpd_ros = reallocf(cfg->vpd.vpd_ros, 1002 (alloc *= 2) * sizeof(*cfg->vpd.vpd_ros), 1003 M_DEVBUF, M_WAITOK | M_ZERO); 1004 } 1005 cfg->vpd.vpd_ros[off].keyword[0] = byte; 1006 if (vpd_nextbyte(&vrs, &byte2)) { 1007 state = -2; 1008 break; 1009 } 1010 cfg->vpd.vpd_ros[off].keyword[1] = byte2; 1011 if (vpd_nextbyte(&vrs, &byte2)) { 1012 state = -2; 1013 break; 1014 } 1015 cfg->vpd.vpd_ros[off].len = dflen = byte2; 1016 if (dflen == 0 && 1017 strncmp(cfg->vpd.vpd_ros[off].keyword, "RV", 1018 2) == 0) { 1019 /* 1020 * if this happens, we can't trust the rest 1021 * of the VPD. 1022 */ 1023 pci_printf(cfg, "bad keyword length: %d\n", 1024 dflen); 1025 cksumvalid = 0; 1026 state = -1; 1027 break; 1028 } else if (dflen == 0) { 1029 cfg->vpd.vpd_ros[off].value = malloc(1 * 1030 sizeof(*cfg->vpd.vpd_ros[off].value), 1031 M_DEVBUF, M_WAITOK); 1032 cfg->vpd.vpd_ros[off].value[0] = '\x00'; 1033 } else 1034 cfg->vpd.vpd_ros[off].value = malloc( 1035 (dflen + 1) * 1036 sizeof(*cfg->vpd.vpd_ros[off].value), 1037 M_DEVBUF, M_WAITOK); 1038 remain -= 3; 1039 i = 0; 1040 /* keep in sync w/ state 3's transistions */ 1041 if (dflen == 0 && remain == 0) 1042 state = 0; 1043 else if (dflen == 0) 1044 state = 2; 1045 else 1046 state = 3; 1047 break; 1048 1049 case 3: /* VPD-R Keyword Value */ 1050 cfg->vpd.vpd_ros[off].value[i++] = byte; 1051 if (strncmp(cfg->vpd.vpd_ros[off].keyword, 1052 "RV", 2) == 0 && cksumvalid == -1) { 1053 if (vrs.cksum == 0) 1054 cksumvalid = 1; 1055 else { 1056 if (bootverbose) 1057 pci_printf(cfg, 1058 "bad VPD cksum, remain %hhu\n", 1059 vrs.cksum); 1060 cksumvalid = 0; 1061 state = -1; 1062 break; 1063 } 1064 } 1065 dflen--; 1066 remain--; 1067 /* keep in sync w/ state 2's transistions */ 1068 if (dflen == 0) 1069 cfg->vpd.vpd_ros[off++].value[i++] = '\0'; 1070 if (dflen == 0 && remain == 0) { 1071 cfg->vpd.vpd_rocnt = off; 1072 cfg->vpd.vpd_ros = reallocf(cfg->vpd.vpd_ros, 1073 off * sizeof(*cfg->vpd.vpd_ros), 1074 M_DEVBUF, M_WAITOK | M_ZERO); 1075 state = 0; 1076 } else if (dflen == 0) 1077 state = 2; 1078 break; 1079 1080 case 4: 1081 remain--; 1082 if (remain == 0) 1083 state = 0; 1084 break; 1085 1086 case 5: /* VPD-W Keyword Header */ 1087 if (off == alloc) { 1088 cfg->vpd.vpd_w = reallocf(cfg->vpd.vpd_w, 1089 (alloc *= 2) * sizeof(*cfg->vpd.vpd_w), 1090 M_DEVBUF, M_WAITOK | M_ZERO); 1091 } 1092 cfg->vpd.vpd_w[off].keyword[0] = byte; 1093 if (vpd_nextbyte(&vrs, &byte2)) { 1094 state = -2; 1095 break; 1096 } 1097 cfg->vpd.vpd_w[off].keyword[1] = byte2; 1098 if (vpd_nextbyte(&vrs, &byte2)) { 1099 state = -2; 1100 break; 1101 } 1102 cfg->vpd.vpd_w[off].len = dflen = byte2; 1103 cfg->vpd.vpd_w[off].start = vrs.off - vrs.bytesinval; 1104 cfg->vpd.vpd_w[off].value = malloc((dflen + 1) * 1105 sizeof(*cfg->vpd.vpd_w[off].value), 1106 M_DEVBUF, M_WAITOK); 1107 remain -= 3; 1108 i = 0; 1109 /* keep in sync w/ state 6's transistions */ 1110 if (dflen == 0 && remain == 0) 1111 state = 0; 1112 else if (dflen == 0) 1113 state = 5; 1114 else 1115 state = 6; 1116 break; 1117 1118 case 6: /* VPD-W Keyword Value */ 1119 cfg->vpd.vpd_w[off].value[i++] = byte; 1120 dflen--; 1121 remain--; 1122 /* keep in sync w/ state 5's transistions */ 1123 if (dflen == 0) 1124 cfg->vpd.vpd_w[off++].value[i++] = '\0'; 1125 if (dflen == 0 && remain == 0) { 1126 cfg->vpd.vpd_wcnt = off; 1127 cfg->vpd.vpd_w = reallocf(cfg->vpd.vpd_w, 1128 off * sizeof(*cfg->vpd.vpd_w), 1129 M_DEVBUF, M_WAITOK | M_ZERO); 1130 state = 0; 1131 } else if (dflen == 0) 1132 state = 5; 1133 break; 1134 1135 default: 1136 pci_printf(cfg, "invalid state: %d\n", state); 1137 state = -1; 1138 break; 1139 } 1140 } 1141 1142 if (cksumvalid == 0 || state < -1) { 1143 /* read-only data bad, clean up */ 1144 if (cfg->vpd.vpd_ros != NULL) { 1145 for (off = 0; cfg->vpd.vpd_ros[off].value; off++) 1146 free(cfg->vpd.vpd_ros[off].value, M_DEVBUF); 1147 free(cfg->vpd.vpd_ros, M_DEVBUF); 1148 cfg->vpd.vpd_ros = NULL; 1149 } 1150 } 1151 if (state < -1) { 1152 /* I/O error, clean up */ 1153 pci_printf(cfg, "failed to read VPD data.\n"); 1154 if (cfg->vpd.vpd_ident != NULL) { 1155 free(cfg->vpd.vpd_ident, M_DEVBUF); 1156 cfg->vpd.vpd_ident = NULL; 1157 } 1158 if (cfg->vpd.vpd_w != NULL) { 1159 for (off = 0; cfg->vpd.vpd_w[off].value; off++) 1160 free(cfg->vpd.vpd_w[off].value, M_DEVBUF); 1161 free(cfg->vpd.vpd_w, M_DEVBUF); 1162 cfg->vpd.vpd_w = NULL; 1163 } 1164 } 1165 cfg->vpd.vpd_cached = 1; 1166 #undef REG 1167 #undef WREG 1168 } 1169 1170 int 1171 pci_get_vpd_ident_method(device_t dev, device_t child, const char **identptr) 1172 { 1173 struct pci_devinfo *dinfo = device_get_ivars(child); 1174 pcicfgregs *cfg = &dinfo->cfg; 1175 1176 if (!cfg->vpd.vpd_cached && cfg->vpd.vpd_reg != 0) 1177 pci_read_vpd(device_get_parent(dev), cfg); 1178 1179 *identptr = cfg->vpd.vpd_ident; 1180 1181 if (*identptr == NULL) 1182 return (ENXIO); 1183 1184 return (0); 1185 } 1186 1187 int 1188 pci_get_vpd_readonly_method(device_t dev, device_t child, const char *kw, 1189 const char **vptr) 1190 { 1191 struct pci_devinfo *dinfo = device_get_ivars(child); 1192 pcicfgregs *cfg = &dinfo->cfg; 1193 int i; 1194 1195 if (!cfg->vpd.vpd_cached && cfg->vpd.vpd_reg != 0) 1196 pci_read_vpd(device_get_parent(dev), cfg); 1197 1198 for (i = 0; i < cfg->vpd.vpd_rocnt; i++) 1199 if (memcmp(kw, cfg->vpd.vpd_ros[i].keyword, 1200 sizeof(cfg->vpd.vpd_ros[i].keyword)) == 0) { 1201 *vptr = cfg->vpd.vpd_ros[i].value; 1202 return (0); 1203 } 1204 1205 *vptr = NULL; 1206 return (ENXIO); 1207 } 1208 1209 struct pcicfg_vpd * 1210 pci_fetch_vpd_list(device_t dev) 1211 { 1212 struct pci_devinfo *dinfo = device_get_ivars(dev); 1213 pcicfgregs *cfg = &dinfo->cfg; 1214 1215 if (!cfg->vpd.vpd_cached && cfg->vpd.vpd_reg != 0) 1216 pci_read_vpd(device_get_parent(device_get_parent(dev)), cfg); 1217 return (&cfg->vpd); 1218 } 1219 1220 /* 1221 * Find the requested HyperTransport capability and return the offset 1222 * in configuration space via the pointer provided. The function 1223 * returns 0 on success and an error code otherwise. 1224 */ 1225 int 1226 pci_find_htcap_method(device_t dev, device_t child, int capability, int *capreg) 1227 { 1228 int ptr, error; 1229 uint16_t val; 1230 1231 error = pci_find_cap(child, PCIY_HT, &ptr); 1232 if (error) 1233 return (error); 1234 1235 /* 1236 * Traverse the capabilities list checking each HT capability 1237 * to see if it matches the requested HT capability. 1238 */ 1239 while (ptr != 0) { 1240 val = pci_read_config(child, ptr + PCIR_HT_COMMAND, 2); 1241 if (capability == PCIM_HTCAP_SLAVE || 1242 capability == PCIM_HTCAP_HOST) 1243 val &= 0xe000; 1244 else 1245 val &= PCIM_HTCMD_CAP_MASK; 1246 if (val == capability) { 1247 if (capreg != NULL) 1248 *capreg = ptr; 1249 return (0); 1250 } 1251 1252 /* Skip to the next HT capability. */ 1253 while (ptr != 0) { 1254 ptr = pci_read_config(child, ptr + PCICAP_NEXTPTR, 1); 1255 if (pci_read_config(child, ptr + PCICAP_ID, 1) == 1256 PCIY_HT) 1257 break; 1258 } 1259 } 1260 return (ENOENT); 1261 } 1262 1263 /* 1264 * Find the requested capability and return the offset in 1265 * configuration space via the pointer provided. The function returns 1266 * 0 on success and an error code otherwise. 1267 */ 1268 int 1269 pci_find_cap_method(device_t dev, device_t child, int capability, 1270 int *capreg) 1271 { 1272 struct pci_devinfo *dinfo = device_get_ivars(child); 1273 pcicfgregs *cfg = &dinfo->cfg; 1274 u_int32_t status; 1275 u_int8_t ptr; 1276 1277 /* 1278 * Check the CAP_LIST bit of the PCI status register first. 1279 */ 1280 status = pci_read_config(child, PCIR_STATUS, 2); 1281 if (!(status & PCIM_STATUS_CAPPRESENT)) 1282 return (ENXIO); 1283 1284 /* 1285 * Determine the start pointer of the capabilities list. 1286 */ 1287 switch (cfg->hdrtype & PCIM_HDRTYPE) { 1288 case PCIM_HDRTYPE_NORMAL: 1289 case PCIM_HDRTYPE_BRIDGE: 1290 ptr = PCIR_CAP_PTR; 1291 break; 1292 case PCIM_HDRTYPE_CARDBUS: 1293 ptr = PCIR_CAP_PTR_2; 1294 break; 1295 default: 1296 /* XXX: panic? */ 1297 return (ENXIO); /* no extended capabilities support */ 1298 } 1299 ptr = pci_read_config(child, ptr, 1); 1300 1301 /* 1302 * Traverse the capabilities list. 1303 */ 1304 while (ptr != 0) { 1305 if (pci_read_config(child, ptr + PCICAP_ID, 1) == capability) { 1306 if (capreg != NULL) 1307 *capreg = ptr; 1308 return (0); 1309 } 1310 ptr = pci_read_config(child, ptr + PCICAP_NEXTPTR, 1); 1311 } 1312 1313 return (ENOENT); 1314 } 1315 1316 /* 1317 * Find the requested extended capability and return the offset in 1318 * configuration space via the pointer provided. The function returns 1319 * 0 on success and an error code otherwise. 1320 */ 1321 int 1322 pci_find_extcap_method(device_t dev, device_t child, int capability, 1323 int *capreg) 1324 { 1325 struct pci_devinfo *dinfo = device_get_ivars(child); 1326 pcicfgregs *cfg = &dinfo->cfg; 1327 uint32_t ecap; 1328 uint16_t ptr; 1329 1330 /* Only supported for PCI-express devices. */ 1331 if (cfg->pcie.pcie_location == 0) 1332 return (ENXIO); 1333 1334 ptr = PCIR_EXTCAP; 1335 ecap = pci_read_config(child, ptr, 4); 1336 if (ecap == 0xffffffff || ecap == 0) 1337 return (ENOENT); 1338 for (;;) { 1339 if (PCI_EXTCAP_ID(ecap) == capability) { 1340 if (capreg != NULL) 1341 *capreg = ptr; 1342 return (0); 1343 } 1344 ptr = PCI_EXTCAP_NEXTPTR(ecap); 1345 if (ptr == 0) 1346 break; 1347 ecap = pci_read_config(child, ptr, 4); 1348 } 1349 1350 return (ENOENT); 1351 } 1352 1353 /* 1354 * Support for MSI-X message interrupts. 1355 */ 1356 void 1357 pci_enable_msix_method(device_t dev, device_t child, u_int index, 1358 uint64_t address, uint32_t data) 1359 { 1360 struct pci_devinfo *dinfo = device_get_ivars(child); 1361 struct pcicfg_msix *msix = &dinfo->cfg.msix; 1362 uint32_t offset; 1363 1364 KASSERT(msix->msix_table_len > index, ("bogus index")); 1365 offset = msix->msix_table_offset + index * 16; 1366 bus_write_4(msix->msix_table_res, offset, address & 0xffffffff); 1367 bus_write_4(msix->msix_table_res, offset + 4, address >> 32); 1368 bus_write_4(msix->msix_table_res, offset + 8, data); 1369 1370 /* Enable MSI -> HT mapping. */ 1371 pci_ht_map_msi(child, address); 1372 } 1373 1374 void 1375 pci_mask_msix(device_t dev, u_int index) 1376 { 1377 struct pci_devinfo *dinfo = device_get_ivars(dev); 1378 struct pcicfg_msix *msix = &dinfo->cfg.msix; 1379 uint32_t offset, val; 1380 1381 KASSERT(msix->msix_msgnum > index, ("bogus index")); 1382 offset = msix->msix_table_offset + index * 16 + 12; 1383 val = bus_read_4(msix->msix_table_res, offset); 1384 if (!(val & PCIM_MSIX_VCTRL_MASK)) { 1385 val |= PCIM_MSIX_VCTRL_MASK; 1386 bus_write_4(msix->msix_table_res, offset, val); 1387 } 1388 } 1389 1390 void 1391 pci_unmask_msix(device_t dev, u_int index) 1392 { 1393 struct pci_devinfo *dinfo = device_get_ivars(dev); 1394 struct pcicfg_msix *msix = &dinfo->cfg.msix; 1395 uint32_t offset, val; 1396 1397 KASSERT(msix->msix_table_len > index, ("bogus index")); 1398 offset = msix->msix_table_offset + index * 16 + 12; 1399 val = bus_read_4(msix->msix_table_res, offset); 1400 if (val & PCIM_MSIX_VCTRL_MASK) { 1401 val &= ~PCIM_MSIX_VCTRL_MASK; 1402 bus_write_4(msix->msix_table_res, offset, val); 1403 } 1404 } 1405 1406 int 1407 pci_pending_msix(device_t dev, u_int index) 1408 { 1409 struct pci_devinfo *dinfo = device_get_ivars(dev); 1410 struct pcicfg_msix *msix = &dinfo->cfg.msix; 1411 uint32_t offset, bit; 1412 1413 KASSERT(msix->msix_table_len > index, ("bogus index")); 1414 offset = msix->msix_pba_offset + (index / 32) * 4; 1415 bit = 1 << index % 32; 1416 return (bus_read_4(msix->msix_pba_res, offset) & bit); 1417 } 1418 1419 /* 1420 * Restore MSI-X registers and table during resume. If MSI-X is 1421 * enabled then walk the virtual table to restore the actual MSI-X 1422 * table. 1423 */ 1424 static void 1425 pci_resume_msix(device_t dev) 1426 { 1427 struct pci_devinfo *dinfo = device_get_ivars(dev); 1428 struct pcicfg_msix *msix = &dinfo->cfg.msix; 1429 struct msix_table_entry *mte; 1430 struct msix_vector *mv; 1431 int i; 1432 1433 if (msix->msix_alloc > 0) { 1434 /* First, mask all vectors. */ 1435 for (i = 0; i < msix->msix_msgnum; i++) 1436 pci_mask_msix(dev, i); 1437 1438 /* Second, program any messages with at least one handler. */ 1439 for (i = 0; i < msix->msix_table_len; i++) { 1440 mte = &msix->msix_table[i]; 1441 if (mte->mte_vector == 0 || mte->mte_handlers == 0) 1442 continue; 1443 mv = &msix->msix_vectors[mte->mte_vector - 1]; 1444 pci_enable_msix(dev, i, mv->mv_address, mv->mv_data); 1445 pci_unmask_msix(dev, i); 1446 } 1447 } 1448 pci_write_config(dev, msix->msix_location + PCIR_MSIX_CTRL, 1449 msix->msix_ctrl, 2); 1450 } 1451 1452 /* 1453 * Attempt to allocate *count MSI-X messages. The actual number allocated is 1454 * returned in *count. After this function returns, each message will be 1455 * available to the driver as SYS_RES_IRQ resources starting at rid 1. 1456 */ 1457 int 1458 pci_alloc_msix_method(device_t dev, device_t child, int *count) 1459 { 1460 struct pci_devinfo *dinfo = device_get_ivars(child); 1461 pcicfgregs *cfg = &dinfo->cfg; 1462 struct resource_list_entry *rle; 1463 int actual, error, i, irq, max; 1464 1465 /* Don't let count == 0 get us into trouble. */ 1466 if (*count == 0) 1467 return (EINVAL); 1468 1469 /* If rid 0 is allocated, then fail. */ 1470 rle = resource_list_find(&dinfo->resources, SYS_RES_IRQ, 0); 1471 if (rle != NULL && rle->res != NULL) 1472 return (ENXIO); 1473 1474 /* Already have allocated messages? */ 1475 if (cfg->msi.msi_alloc != 0 || cfg->msix.msix_alloc != 0) 1476 return (ENXIO); 1477 1478 /* If MSI-X is blacklisted for this system, fail. */ 1479 if (pci_msix_blacklisted()) 1480 return (ENXIO); 1481 1482 /* MSI-X capability present? */ 1483 if (cfg->msix.msix_location == 0 || !pci_do_msix) 1484 return (ENODEV); 1485 1486 /* Make sure the appropriate BARs are mapped. */ 1487 rle = resource_list_find(&dinfo->resources, SYS_RES_MEMORY, 1488 cfg->msix.msix_table_bar); 1489 if (rle == NULL || rle->res == NULL || 1490 !(rman_get_flags(rle->res) & RF_ACTIVE)) 1491 return (ENXIO); 1492 cfg->msix.msix_table_res = rle->res; 1493 if (cfg->msix.msix_pba_bar != cfg->msix.msix_table_bar) { 1494 rle = resource_list_find(&dinfo->resources, SYS_RES_MEMORY, 1495 cfg->msix.msix_pba_bar); 1496 if (rle == NULL || rle->res == NULL || 1497 !(rman_get_flags(rle->res) & RF_ACTIVE)) 1498 return (ENXIO); 1499 } 1500 cfg->msix.msix_pba_res = rle->res; 1501 1502 if (bootverbose) 1503 device_printf(child, 1504 "attempting to allocate %d MSI-X vectors (%d supported)\n", 1505 *count, cfg->msix.msix_msgnum); 1506 max = min(*count, cfg->msix.msix_msgnum); 1507 for (i = 0; i < max; i++) { 1508 /* Allocate a message. */ 1509 error = PCIB_ALLOC_MSIX(device_get_parent(dev), child, &irq); 1510 if (error) { 1511 if (i == 0) 1512 return (error); 1513 break; 1514 } 1515 resource_list_add(&dinfo->resources, SYS_RES_IRQ, i + 1, irq, 1516 irq, 1); 1517 } 1518 actual = i; 1519 1520 if (bootverbose) { 1521 rle = resource_list_find(&dinfo->resources, SYS_RES_IRQ, 1); 1522 if (actual == 1) 1523 device_printf(child, "using IRQ %lu for MSI-X\n", 1524 rle->start); 1525 else { 1526 int run; 1527 1528 /* 1529 * Be fancy and try to print contiguous runs of 1530 * IRQ values as ranges. 'irq' is the previous IRQ. 1531 * 'run' is true if we are in a range. 1532 */ 1533 device_printf(child, "using IRQs %lu", rle->start); 1534 irq = rle->start; 1535 run = 0; 1536 for (i = 1; i < actual; i++) { 1537 rle = resource_list_find(&dinfo->resources, 1538 SYS_RES_IRQ, i + 1); 1539 1540 /* Still in a run? */ 1541 if (rle->start == irq + 1) { 1542 run = 1; 1543 irq++; 1544 continue; 1545 } 1546 1547 /* Finish previous range. */ 1548 if (run) { 1549 printf("-%d", irq); 1550 run = 0; 1551 } 1552 1553 /* Start new range. */ 1554 printf(",%lu", rle->start); 1555 irq = rle->start; 1556 } 1557 1558 /* Unfinished range? */ 1559 if (run) 1560 printf("-%d", irq); 1561 printf(" for MSI-X\n"); 1562 } 1563 } 1564 1565 /* Mask all vectors. */ 1566 for (i = 0; i < cfg->msix.msix_msgnum; i++) 1567 pci_mask_msix(child, i); 1568 1569 /* Allocate and initialize vector data and virtual table. */ 1570 cfg->msix.msix_vectors = malloc(sizeof(struct msix_vector) * actual, 1571 M_DEVBUF, M_WAITOK | M_ZERO); 1572 cfg->msix.msix_table = malloc(sizeof(struct msix_table_entry) * actual, 1573 M_DEVBUF, M_WAITOK | M_ZERO); 1574 for (i = 0; i < actual; i++) { 1575 rle = resource_list_find(&dinfo->resources, SYS_RES_IRQ, i + 1); 1576 cfg->msix.msix_vectors[i].mv_irq = rle->start; 1577 cfg->msix.msix_table[i].mte_vector = i + 1; 1578 } 1579 1580 /* Update control register to enable MSI-X. */ 1581 cfg->msix.msix_ctrl |= PCIM_MSIXCTRL_MSIX_ENABLE; 1582 pci_write_config(child, cfg->msix.msix_location + PCIR_MSIX_CTRL, 1583 cfg->msix.msix_ctrl, 2); 1584 1585 /* Update counts of alloc'd messages. */ 1586 cfg->msix.msix_alloc = actual; 1587 cfg->msix.msix_table_len = actual; 1588 *count = actual; 1589 return (0); 1590 } 1591 1592 /* 1593 * By default, pci_alloc_msix() will assign the allocated IRQ 1594 * resources consecutively to the first N messages in the MSI-X table. 1595 * However, device drivers may want to use different layouts if they 1596 * either receive fewer messages than they asked for, or they wish to 1597 * populate the MSI-X table sparsely. This method allows the driver 1598 * to specify what layout it wants. It must be called after a 1599 * successful pci_alloc_msix() but before any of the associated 1600 * SYS_RES_IRQ resources are allocated via bus_alloc_resource(). 1601 * 1602 * The 'vectors' array contains 'count' message vectors. The array 1603 * maps directly to the MSI-X table in that index 0 in the array 1604 * specifies the vector for the first message in the MSI-X table, etc. 1605 * The vector value in each array index can either be 0 to indicate 1606 * that no vector should be assigned to a message slot, or it can be a 1607 * number from 1 to N (where N is the count returned from a 1608 * succcessful call to pci_alloc_msix()) to indicate which message 1609 * vector (IRQ) to be used for the corresponding message. 1610 * 1611 * On successful return, each message with a non-zero vector will have 1612 * an associated SYS_RES_IRQ whose rid is equal to the array index + 1613 * 1. Additionally, if any of the IRQs allocated via the previous 1614 * call to pci_alloc_msix() are not used in the mapping, those IRQs 1615 * will be freed back to the system automatically. 1616 * 1617 * For example, suppose a driver has a MSI-X table with 6 messages and 1618 * asks for 6 messages, but pci_alloc_msix() only returns a count of 1619 * 3. Call the three vectors allocated by pci_alloc_msix() A, B, and 1620 * C. After the call to pci_alloc_msix(), the device will be setup to 1621 * have an MSI-X table of ABC--- (where - means no vector assigned). 1622 * If the driver then passes a vector array of { 1, 0, 1, 2, 0, 2 }, 1623 * then the MSI-X table will look like A-AB-B, and the 'C' vector will 1624 * be freed back to the system. This device will also have valid 1625 * SYS_RES_IRQ rids of 1, 3, 4, and 6. 1626 * 1627 * In any case, the SYS_RES_IRQ rid X will always map to the message 1628 * at MSI-X table index X - 1 and will only be valid if a vector is 1629 * assigned to that table entry. 1630 */ 1631 int 1632 pci_remap_msix_method(device_t dev, device_t child, int count, 1633 const u_int *vectors) 1634 { 1635 struct pci_devinfo *dinfo = device_get_ivars(child); 1636 struct pcicfg_msix *msix = &dinfo->cfg.msix; 1637 struct resource_list_entry *rle; 1638 int i, irq, j, *used; 1639 1640 /* 1641 * Have to have at least one message in the table but the 1642 * table can't be bigger than the actual MSI-X table in the 1643 * device. 1644 */ 1645 if (count == 0 || count > msix->msix_msgnum) 1646 return (EINVAL); 1647 1648 /* Sanity check the vectors. */ 1649 for (i = 0; i < count; i++) 1650 if (vectors[i] > msix->msix_alloc) 1651 return (EINVAL); 1652 1653 /* 1654 * Make sure there aren't any holes in the vectors to be used. 1655 * It's a big pain to support it, and it doesn't really make 1656 * sense anyway. Also, at least one vector must be used. 1657 */ 1658 used = malloc(sizeof(int) * msix->msix_alloc, M_DEVBUF, M_WAITOK | 1659 M_ZERO); 1660 for (i = 0; i < count; i++) 1661 if (vectors[i] != 0) 1662 used[vectors[i] - 1] = 1; 1663 for (i = 0; i < msix->msix_alloc - 1; i++) 1664 if (used[i] == 0 && used[i + 1] == 1) { 1665 free(used, M_DEVBUF); 1666 return (EINVAL); 1667 } 1668 if (used[0] != 1) { 1669 free(used, M_DEVBUF); 1670 return (EINVAL); 1671 } 1672 1673 /* Make sure none of the resources are allocated. */ 1674 for (i = 0; i < msix->msix_table_len; i++) { 1675 if (msix->msix_table[i].mte_vector == 0) 1676 continue; 1677 if (msix->msix_table[i].mte_handlers > 0) 1678 return (EBUSY); 1679 rle = resource_list_find(&dinfo->resources, SYS_RES_IRQ, i + 1); 1680 KASSERT(rle != NULL, ("missing resource")); 1681 if (rle->res != NULL) 1682 return (EBUSY); 1683 } 1684 1685 /* Free the existing resource list entries. */ 1686 for (i = 0; i < msix->msix_table_len; i++) { 1687 if (msix->msix_table[i].mte_vector == 0) 1688 continue; 1689 resource_list_delete(&dinfo->resources, SYS_RES_IRQ, i + 1); 1690 } 1691 1692 /* 1693 * Build the new virtual table keeping track of which vectors are 1694 * used. 1695 */ 1696 free(msix->msix_table, M_DEVBUF); 1697 msix->msix_table = malloc(sizeof(struct msix_table_entry) * count, 1698 M_DEVBUF, M_WAITOK | M_ZERO); 1699 for (i = 0; i < count; i++) 1700 msix->msix_table[i].mte_vector = vectors[i]; 1701 msix->msix_table_len = count; 1702 1703 /* Free any unused IRQs and resize the vectors array if necessary. */ 1704 j = msix->msix_alloc - 1; 1705 if (used[j] == 0) { 1706 struct msix_vector *vec; 1707 1708 while (used[j] == 0) { 1709 PCIB_RELEASE_MSIX(device_get_parent(dev), child, 1710 msix->msix_vectors[j].mv_irq); 1711 j--; 1712 } 1713 vec = malloc(sizeof(struct msix_vector) * (j + 1), M_DEVBUF, 1714 M_WAITOK); 1715 bcopy(msix->msix_vectors, vec, sizeof(struct msix_vector) * 1716 (j + 1)); 1717 free(msix->msix_vectors, M_DEVBUF); 1718 msix->msix_vectors = vec; 1719 msix->msix_alloc = j + 1; 1720 } 1721 free(used, M_DEVBUF); 1722 1723 /* Map the IRQs onto the rids. */ 1724 for (i = 0; i < count; i++) { 1725 if (vectors[i] == 0) 1726 continue; 1727 irq = msix->msix_vectors[vectors[i]].mv_irq; 1728 resource_list_add(&dinfo->resources, SYS_RES_IRQ, i + 1, irq, 1729 irq, 1); 1730 } 1731 1732 if (bootverbose) { 1733 device_printf(child, "Remapped MSI-X IRQs as: "); 1734 for (i = 0; i < count; i++) { 1735 if (i != 0) 1736 printf(", "); 1737 if (vectors[i] == 0) 1738 printf("---"); 1739 else 1740 printf("%d", 1741 msix->msix_vectors[vectors[i]].mv_irq); 1742 } 1743 printf("\n"); 1744 } 1745 1746 return (0); 1747 } 1748 1749 static int 1750 pci_release_msix(device_t dev, device_t child) 1751 { 1752 struct pci_devinfo *dinfo = device_get_ivars(child); 1753 struct pcicfg_msix *msix = &dinfo->cfg.msix; 1754 struct resource_list_entry *rle; 1755 int i; 1756 1757 /* Do we have any messages to release? */ 1758 if (msix->msix_alloc == 0) 1759 return (ENODEV); 1760 1761 /* Make sure none of the resources are allocated. */ 1762 for (i = 0; i < msix->msix_table_len; i++) { 1763 if (msix->msix_table[i].mte_vector == 0) 1764 continue; 1765 if (msix->msix_table[i].mte_handlers > 0) 1766 return (EBUSY); 1767 rle = resource_list_find(&dinfo->resources, SYS_RES_IRQ, i + 1); 1768 KASSERT(rle != NULL, ("missing resource")); 1769 if (rle->res != NULL) 1770 return (EBUSY); 1771 } 1772 1773 /* Update control register to disable MSI-X. */ 1774 msix->msix_ctrl &= ~PCIM_MSIXCTRL_MSIX_ENABLE; 1775 pci_write_config(child, msix->msix_location + PCIR_MSIX_CTRL, 1776 msix->msix_ctrl, 2); 1777 1778 /* Free the resource list entries. */ 1779 for (i = 0; i < msix->msix_table_len; i++) { 1780 if (msix->msix_table[i].mte_vector == 0) 1781 continue; 1782 resource_list_delete(&dinfo->resources, SYS_RES_IRQ, i + 1); 1783 } 1784 free(msix->msix_table, M_DEVBUF); 1785 msix->msix_table_len = 0; 1786 1787 /* Release the IRQs. */ 1788 for (i = 0; i < msix->msix_alloc; i++) 1789 PCIB_RELEASE_MSIX(device_get_parent(dev), child, 1790 msix->msix_vectors[i].mv_irq); 1791 free(msix->msix_vectors, M_DEVBUF); 1792 msix->msix_alloc = 0; 1793 return (0); 1794 } 1795 1796 /* 1797 * Return the max supported MSI-X messages this device supports. 1798 * Basically, assuming the MD code can alloc messages, this function 1799 * should return the maximum value that pci_alloc_msix() can return. 1800 * Thus, it is subject to the tunables, etc. 1801 */ 1802 int 1803 pci_msix_count_method(device_t dev, device_t child) 1804 { 1805 struct pci_devinfo *dinfo = device_get_ivars(child); 1806 struct pcicfg_msix *msix = &dinfo->cfg.msix; 1807 1808 if (pci_do_msix && msix->msix_location != 0) 1809 return (msix->msix_msgnum); 1810 return (0); 1811 } 1812 1813 /* 1814 * HyperTransport MSI mapping control 1815 */ 1816 void 1817 pci_ht_map_msi(device_t dev, uint64_t addr) 1818 { 1819 struct pci_devinfo *dinfo = device_get_ivars(dev); 1820 struct pcicfg_ht *ht = &dinfo->cfg.ht; 1821 1822 if (!ht->ht_msimap) 1823 return; 1824 1825 if (addr && !(ht->ht_msictrl & PCIM_HTCMD_MSI_ENABLE) && 1826 ht->ht_msiaddr >> 20 == addr >> 20) { 1827 /* Enable MSI -> HT mapping. */ 1828 ht->ht_msictrl |= PCIM_HTCMD_MSI_ENABLE; 1829 pci_write_config(dev, ht->ht_msimap + PCIR_HT_COMMAND, 1830 ht->ht_msictrl, 2); 1831 } 1832 1833 if (!addr && ht->ht_msictrl & PCIM_HTCMD_MSI_ENABLE) { 1834 /* Disable MSI -> HT mapping. */ 1835 ht->ht_msictrl &= ~PCIM_HTCMD_MSI_ENABLE; 1836 pci_write_config(dev, ht->ht_msimap + PCIR_HT_COMMAND, 1837 ht->ht_msictrl, 2); 1838 } 1839 } 1840 1841 int 1842 pci_get_max_read_req(device_t dev) 1843 { 1844 struct pci_devinfo *dinfo = device_get_ivars(dev); 1845 int cap; 1846 uint16_t val; 1847 1848 cap = dinfo->cfg.pcie.pcie_location; 1849 if (cap == 0) 1850 return (0); 1851 val = pci_read_config(dev, cap + PCIER_DEVICE_CTL, 2); 1852 val &= PCIEM_CTL_MAX_READ_REQUEST; 1853 val >>= 12; 1854 return (1 << (val + 7)); 1855 } 1856 1857 int 1858 pci_set_max_read_req(device_t dev, int size) 1859 { 1860 struct pci_devinfo *dinfo = device_get_ivars(dev); 1861 int cap; 1862 uint16_t val; 1863 1864 cap = dinfo->cfg.pcie.pcie_location; 1865 if (cap == 0) 1866 return (0); 1867 if (size < 128) 1868 size = 128; 1869 if (size > 4096) 1870 size = 4096; 1871 size = (1 << (fls(size) - 1)); 1872 val = pci_read_config(dev, cap + PCIER_DEVICE_CTL, 2); 1873 val &= ~PCIEM_CTL_MAX_READ_REQUEST; 1874 val |= (fls(size) - 8) << 12; 1875 pci_write_config(dev, cap + PCIER_DEVICE_CTL, val, 2); 1876 return (size); 1877 } 1878 1879 /* 1880 * Support for MSI message signalled interrupts. 1881 */ 1882 void 1883 pci_enable_msi_method(device_t dev, device_t child, uint64_t address, 1884 uint16_t data) 1885 { 1886 struct pci_devinfo *dinfo = device_get_ivars(child); 1887 struct pcicfg_msi *msi = &dinfo->cfg.msi; 1888 1889 /* Write data and address values. */ 1890 pci_write_config(child, msi->msi_location + PCIR_MSI_ADDR, 1891 address & 0xffffffff, 4); 1892 if (msi->msi_ctrl & PCIM_MSICTRL_64BIT) { 1893 pci_write_config(child, msi->msi_location + PCIR_MSI_ADDR_HIGH, 1894 address >> 32, 4); 1895 pci_write_config(child, msi->msi_location + PCIR_MSI_DATA_64BIT, 1896 data, 2); 1897 } else 1898 pci_write_config(child, msi->msi_location + PCIR_MSI_DATA, data, 1899 2); 1900 1901 /* Enable MSI in the control register. */ 1902 msi->msi_ctrl |= PCIM_MSICTRL_MSI_ENABLE; 1903 pci_write_config(child, msi->msi_location + PCIR_MSI_CTRL, 1904 msi->msi_ctrl, 2); 1905 1906 /* Enable MSI -> HT mapping. */ 1907 pci_ht_map_msi(child, address); 1908 } 1909 1910 void 1911 pci_disable_msi_method(device_t dev, device_t child) 1912 { 1913 struct pci_devinfo *dinfo = device_get_ivars(child); 1914 struct pcicfg_msi *msi = &dinfo->cfg.msi; 1915 1916 /* Disable MSI -> HT mapping. */ 1917 pci_ht_map_msi(child, 0); 1918 1919 /* Disable MSI in the control register. */ 1920 msi->msi_ctrl &= ~PCIM_MSICTRL_MSI_ENABLE; 1921 pci_write_config(child, msi->msi_location + PCIR_MSI_CTRL, 1922 msi->msi_ctrl, 2); 1923 } 1924 1925 /* 1926 * Restore MSI registers during resume. If MSI is enabled then 1927 * restore the data and address registers in addition to the control 1928 * register. 1929 */ 1930 static void 1931 pci_resume_msi(device_t dev) 1932 { 1933 struct pci_devinfo *dinfo = device_get_ivars(dev); 1934 struct pcicfg_msi *msi = &dinfo->cfg.msi; 1935 uint64_t address; 1936 uint16_t data; 1937 1938 if (msi->msi_ctrl & PCIM_MSICTRL_MSI_ENABLE) { 1939 address = msi->msi_addr; 1940 data = msi->msi_data; 1941 pci_write_config(dev, msi->msi_location + PCIR_MSI_ADDR, 1942 address & 0xffffffff, 4); 1943 if (msi->msi_ctrl & PCIM_MSICTRL_64BIT) { 1944 pci_write_config(dev, msi->msi_location + 1945 PCIR_MSI_ADDR_HIGH, address >> 32, 4); 1946 pci_write_config(dev, msi->msi_location + 1947 PCIR_MSI_DATA_64BIT, data, 2); 1948 } else 1949 pci_write_config(dev, msi->msi_location + PCIR_MSI_DATA, 1950 data, 2); 1951 } 1952 pci_write_config(dev, msi->msi_location + PCIR_MSI_CTRL, msi->msi_ctrl, 1953 2); 1954 } 1955 1956 static int 1957 pci_remap_intr_method(device_t bus, device_t dev, u_int irq) 1958 { 1959 struct pci_devinfo *dinfo = device_get_ivars(dev); 1960 pcicfgregs *cfg = &dinfo->cfg; 1961 struct resource_list_entry *rle; 1962 struct msix_table_entry *mte; 1963 struct msix_vector *mv; 1964 uint64_t addr; 1965 uint32_t data; 1966 int error, i, j; 1967 1968 /* 1969 * Handle MSI first. We try to find this IRQ among our list 1970 * of MSI IRQs. If we find it, we request updated address and 1971 * data registers and apply the results. 1972 */ 1973 if (cfg->msi.msi_alloc > 0) { 1974 1975 /* If we don't have any active handlers, nothing to do. */ 1976 if (cfg->msi.msi_handlers == 0) 1977 return (0); 1978 for (i = 0; i < cfg->msi.msi_alloc; i++) { 1979 rle = resource_list_find(&dinfo->resources, SYS_RES_IRQ, 1980 i + 1); 1981 if (rle->start == irq) { 1982 error = PCIB_MAP_MSI(device_get_parent(bus), 1983 dev, irq, &addr, &data); 1984 if (error) 1985 return (error); 1986 pci_disable_msi(dev); 1987 dinfo->cfg.msi.msi_addr = addr; 1988 dinfo->cfg.msi.msi_data = data; 1989 pci_enable_msi(dev, addr, data); 1990 return (0); 1991 } 1992 } 1993 return (ENOENT); 1994 } 1995 1996 /* 1997 * For MSI-X, we check to see if we have this IRQ. If we do, 1998 * we request the updated mapping info. If that works, we go 1999 * through all the slots that use this IRQ and update them. 2000 */ 2001 if (cfg->msix.msix_alloc > 0) { 2002 for (i = 0; i < cfg->msix.msix_alloc; i++) { 2003 mv = &cfg->msix.msix_vectors[i]; 2004 if (mv->mv_irq == irq) { 2005 error = PCIB_MAP_MSI(device_get_parent(bus), 2006 dev, irq, &addr, &data); 2007 if (error) 2008 return (error); 2009 mv->mv_address = addr; 2010 mv->mv_data = data; 2011 for (j = 0; j < cfg->msix.msix_table_len; j++) { 2012 mte = &cfg->msix.msix_table[j]; 2013 if (mte->mte_vector != i + 1) 2014 continue; 2015 if (mte->mte_handlers == 0) 2016 continue; 2017 pci_mask_msix(dev, j); 2018 pci_enable_msix(dev, j, addr, data); 2019 pci_unmask_msix(dev, j); 2020 } 2021 } 2022 } 2023 return (ENOENT); 2024 } 2025 2026 return (ENOENT); 2027 } 2028 2029 /* 2030 * Returns true if the specified device is blacklisted because MSI 2031 * doesn't work. 2032 */ 2033 int 2034 pci_msi_device_blacklisted(device_t dev) 2035 { 2036 2037 if (!pci_honor_msi_blacklist) 2038 return (0); 2039 2040 return (pci_has_quirk(pci_get_devid(dev), PCI_QUIRK_DISABLE_MSI)); 2041 } 2042 2043 /* 2044 * Determine if MSI is blacklisted globally on this system. Currently, 2045 * we just check for blacklisted chipsets as represented by the 2046 * host-PCI bridge at device 0:0:0. In the future, it may become 2047 * necessary to check other system attributes, such as the kenv values 2048 * that give the motherboard manufacturer and model number. 2049 */ 2050 static int 2051 pci_msi_blacklisted(void) 2052 { 2053 device_t dev; 2054 2055 if (!pci_honor_msi_blacklist) 2056 return (0); 2057 2058 /* Blacklist all non-PCI-express and non-PCI-X chipsets. */ 2059 if (!(pcie_chipset || pcix_chipset)) { 2060 if (vm_guest != VM_GUEST_NO) { 2061 /* 2062 * Whitelist older chipsets in virtual 2063 * machines known to support MSI. 2064 */ 2065 dev = pci_find_bsf(0, 0, 0); 2066 if (dev != NULL) 2067 return (!pci_has_quirk(pci_get_devid(dev), 2068 PCI_QUIRK_ENABLE_MSI_VM)); 2069 } 2070 return (1); 2071 } 2072 2073 dev = pci_find_bsf(0, 0, 0); 2074 if (dev != NULL) 2075 return (pci_msi_device_blacklisted(dev)); 2076 return (0); 2077 } 2078 2079 /* 2080 * Returns true if the specified device is blacklisted because MSI-X 2081 * doesn't work. Note that this assumes that if MSI doesn't work, 2082 * MSI-X doesn't either. 2083 */ 2084 int 2085 pci_msix_device_blacklisted(device_t dev) 2086 { 2087 2088 if (!pci_honor_msi_blacklist) 2089 return (0); 2090 2091 if (pci_has_quirk(pci_get_devid(dev), PCI_QUIRK_DISABLE_MSIX)) 2092 return (1); 2093 2094 return (pci_msi_device_blacklisted(dev)); 2095 } 2096 2097 /* 2098 * Determine if MSI-X is blacklisted globally on this system. If MSI 2099 * is blacklisted, assume that MSI-X is as well. Check for additional 2100 * chipsets where MSI works but MSI-X does not. 2101 */ 2102 static int 2103 pci_msix_blacklisted(void) 2104 { 2105 device_t dev; 2106 2107 if (!pci_honor_msi_blacklist) 2108 return (0); 2109 2110 dev = pci_find_bsf(0, 0, 0); 2111 if (dev != NULL && pci_has_quirk(pci_get_devid(dev), 2112 PCI_QUIRK_DISABLE_MSIX)) 2113 return (1); 2114 2115 return (pci_msi_blacklisted()); 2116 } 2117 2118 /* 2119 * Attempt to allocate *count MSI messages. The actual number allocated is 2120 * returned in *count. After this function returns, each message will be 2121 * available to the driver as SYS_RES_IRQ resources starting at a rid 1. 2122 */ 2123 int 2124 pci_alloc_msi_method(device_t dev, device_t child, int *count) 2125 { 2126 struct pci_devinfo *dinfo = device_get_ivars(child); 2127 pcicfgregs *cfg = &dinfo->cfg; 2128 struct resource_list_entry *rle; 2129 int actual, error, i, irqs[32]; 2130 uint16_t ctrl; 2131 2132 /* Don't let count == 0 get us into trouble. */ 2133 if (*count == 0) 2134 return (EINVAL); 2135 2136 /* If rid 0 is allocated, then fail. */ 2137 rle = resource_list_find(&dinfo->resources, SYS_RES_IRQ, 0); 2138 if (rle != NULL && rle->res != NULL) 2139 return (ENXIO); 2140 2141 /* Already have allocated messages? */ 2142 if (cfg->msi.msi_alloc != 0 || cfg->msix.msix_alloc != 0) 2143 return (ENXIO); 2144 2145 /* If MSI is blacklisted for this system, fail. */ 2146 if (pci_msi_blacklisted()) 2147 return (ENXIO); 2148 2149 /* MSI capability present? */ 2150 if (cfg->msi.msi_location == 0 || !pci_do_msi) 2151 return (ENODEV); 2152 2153 if (bootverbose) 2154 device_printf(child, 2155 "attempting to allocate %d MSI vectors (%d supported)\n", 2156 *count, cfg->msi.msi_msgnum); 2157 2158 /* Don't ask for more than the device supports. */ 2159 actual = min(*count, cfg->msi.msi_msgnum); 2160 2161 /* Don't ask for more than 32 messages. */ 2162 actual = min(actual, 32); 2163 2164 /* MSI requires power of 2 number of messages. */ 2165 if (!powerof2(actual)) 2166 return (EINVAL); 2167 2168 for (;;) { 2169 /* Try to allocate N messages. */ 2170 error = PCIB_ALLOC_MSI(device_get_parent(dev), child, actual, 2171 actual, irqs); 2172 if (error == 0) 2173 break; 2174 if (actual == 1) 2175 return (error); 2176 2177 /* Try N / 2. */ 2178 actual >>= 1; 2179 } 2180 2181 /* 2182 * We now have N actual messages mapped onto SYS_RES_IRQ 2183 * resources in the irqs[] array, so add new resources 2184 * starting at rid 1. 2185 */ 2186 for (i = 0; i < actual; i++) 2187 resource_list_add(&dinfo->resources, SYS_RES_IRQ, i + 1, 2188 irqs[i], irqs[i], 1); 2189 2190 if (bootverbose) { 2191 if (actual == 1) 2192 device_printf(child, "using IRQ %d for MSI\n", irqs[0]); 2193 else { 2194 int run; 2195 2196 /* 2197 * Be fancy and try to print contiguous runs 2198 * of IRQ values as ranges. 'run' is true if 2199 * we are in a range. 2200 */ 2201 device_printf(child, "using IRQs %d", irqs[0]); 2202 run = 0; 2203 for (i = 1; i < actual; i++) { 2204 2205 /* Still in a run? */ 2206 if (irqs[i] == irqs[i - 1] + 1) { 2207 run = 1; 2208 continue; 2209 } 2210 2211 /* Finish previous range. */ 2212 if (run) { 2213 printf("-%d", irqs[i - 1]); 2214 run = 0; 2215 } 2216 2217 /* Start new range. */ 2218 printf(",%d", irqs[i]); 2219 } 2220 2221 /* Unfinished range? */ 2222 if (run) 2223 printf("-%d", irqs[actual - 1]); 2224 printf(" for MSI\n"); 2225 } 2226 } 2227 2228 /* Update control register with actual count. */ 2229 ctrl = cfg->msi.msi_ctrl; 2230 ctrl &= ~PCIM_MSICTRL_MME_MASK; 2231 ctrl |= (ffs(actual) - 1) << 4; 2232 cfg->msi.msi_ctrl = ctrl; 2233 pci_write_config(child, cfg->msi.msi_location + PCIR_MSI_CTRL, ctrl, 2); 2234 2235 /* Update counts of alloc'd messages. */ 2236 cfg->msi.msi_alloc = actual; 2237 cfg->msi.msi_handlers = 0; 2238 *count = actual; 2239 return (0); 2240 } 2241 2242 /* Release the MSI messages associated with this device. */ 2243 int 2244 pci_release_msi_method(device_t dev, device_t child) 2245 { 2246 struct pci_devinfo *dinfo = device_get_ivars(child); 2247 struct pcicfg_msi *msi = &dinfo->cfg.msi; 2248 struct resource_list_entry *rle; 2249 int error, i, irqs[32]; 2250 2251 /* Try MSI-X first. */ 2252 error = pci_release_msix(dev, child); 2253 if (error != ENODEV) 2254 return (error); 2255 2256 /* Do we have any messages to release? */ 2257 if (msi->msi_alloc == 0) 2258 return (ENODEV); 2259 KASSERT(msi->msi_alloc <= 32, ("more than 32 alloc'd messages")); 2260 2261 /* Make sure none of the resources are allocated. */ 2262 if (msi->msi_handlers > 0) 2263 return (EBUSY); 2264 for (i = 0; i < msi->msi_alloc; i++) { 2265 rle = resource_list_find(&dinfo->resources, SYS_RES_IRQ, i + 1); 2266 KASSERT(rle != NULL, ("missing MSI resource")); 2267 if (rle->res != NULL) 2268 return (EBUSY); 2269 irqs[i] = rle->start; 2270 } 2271 2272 /* Update control register with 0 count. */ 2273 KASSERT(!(msi->msi_ctrl & PCIM_MSICTRL_MSI_ENABLE), 2274 ("%s: MSI still enabled", __func__)); 2275 msi->msi_ctrl &= ~PCIM_MSICTRL_MME_MASK; 2276 pci_write_config(child, msi->msi_location + PCIR_MSI_CTRL, 2277 msi->msi_ctrl, 2); 2278 2279 /* Release the messages. */ 2280 PCIB_RELEASE_MSI(device_get_parent(dev), child, msi->msi_alloc, irqs); 2281 for (i = 0; i < msi->msi_alloc; i++) 2282 resource_list_delete(&dinfo->resources, SYS_RES_IRQ, i + 1); 2283 2284 /* Update alloc count. */ 2285 msi->msi_alloc = 0; 2286 msi->msi_addr = 0; 2287 msi->msi_data = 0; 2288 return (0); 2289 } 2290 2291 /* 2292 * Return the max supported MSI messages this device supports. 2293 * Basically, assuming the MD code can alloc messages, this function 2294 * should return the maximum value that pci_alloc_msi() can return. 2295 * Thus, it is subject to the tunables, etc. 2296 */ 2297 int 2298 pci_msi_count_method(device_t dev, device_t child) 2299 { 2300 struct pci_devinfo *dinfo = device_get_ivars(child); 2301 struct pcicfg_msi *msi = &dinfo->cfg.msi; 2302 2303 if (pci_do_msi && msi->msi_location != 0) 2304 return (msi->msi_msgnum); 2305 return (0); 2306 } 2307 2308 /* free pcicfgregs structure and all depending data structures */ 2309 2310 int 2311 pci_freecfg(struct pci_devinfo *dinfo) 2312 { 2313 struct devlist *devlist_head; 2314 struct pci_map *pm, *next; 2315 int i; 2316 2317 devlist_head = &pci_devq; 2318 2319 if (dinfo->cfg.vpd.vpd_reg) { 2320 free(dinfo->cfg.vpd.vpd_ident, M_DEVBUF); 2321 for (i = 0; i < dinfo->cfg.vpd.vpd_rocnt; i++) 2322 free(dinfo->cfg.vpd.vpd_ros[i].value, M_DEVBUF); 2323 free(dinfo->cfg.vpd.vpd_ros, M_DEVBUF); 2324 for (i = 0; i < dinfo->cfg.vpd.vpd_wcnt; i++) 2325 free(dinfo->cfg.vpd.vpd_w[i].value, M_DEVBUF); 2326 free(dinfo->cfg.vpd.vpd_w, M_DEVBUF); 2327 } 2328 STAILQ_FOREACH_SAFE(pm, &dinfo->cfg.maps, pm_link, next) { 2329 free(pm, M_DEVBUF); 2330 } 2331 STAILQ_REMOVE(devlist_head, dinfo, pci_devinfo, pci_links); 2332 free(dinfo, M_DEVBUF); 2333 2334 /* increment the generation count */ 2335 pci_generation++; 2336 2337 /* we're losing one device */ 2338 pci_numdevs--; 2339 return (0); 2340 } 2341 2342 /* 2343 * PCI power manangement 2344 */ 2345 int 2346 pci_set_powerstate_method(device_t dev, device_t child, int state) 2347 { 2348 struct pci_devinfo *dinfo = device_get_ivars(child); 2349 pcicfgregs *cfg = &dinfo->cfg; 2350 uint16_t status; 2351 int result, oldstate, highest, delay; 2352 2353 if (cfg->pp.pp_cap == 0) 2354 return (EOPNOTSUPP); 2355 2356 /* 2357 * Optimize a no state change request away. While it would be OK to 2358 * write to the hardware in theory, some devices have shown odd 2359 * behavior when going from D3 -> D3. 2360 */ 2361 oldstate = pci_get_powerstate(child); 2362 if (oldstate == state) 2363 return (0); 2364 2365 /* 2366 * The PCI power management specification states that after a state 2367 * transition between PCI power states, system software must 2368 * guarantee a minimal delay before the function accesses the device. 2369 * Compute the worst case delay that we need to guarantee before we 2370 * access the device. Many devices will be responsive much more 2371 * quickly than this delay, but there are some that don't respond 2372 * instantly to state changes. Transitions to/from D3 state require 2373 * 10ms, while D2 requires 200us, and D0/1 require none. The delay 2374 * is done below with DELAY rather than a sleeper function because 2375 * this function can be called from contexts where we cannot sleep. 2376 */ 2377 highest = (oldstate > state) ? oldstate : state; 2378 if (highest == PCI_POWERSTATE_D3) 2379 delay = 10000; 2380 else if (highest == PCI_POWERSTATE_D2) 2381 delay = 200; 2382 else 2383 delay = 0; 2384 status = PCI_READ_CONFIG(dev, child, cfg->pp.pp_status, 2) 2385 & ~PCIM_PSTAT_DMASK; 2386 result = 0; 2387 switch (state) { 2388 case PCI_POWERSTATE_D0: 2389 status |= PCIM_PSTAT_D0; 2390 break; 2391 case PCI_POWERSTATE_D1: 2392 if ((cfg->pp.pp_cap & PCIM_PCAP_D1SUPP) == 0) 2393 return (EOPNOTSUPP); 2394 status |= PCIM_PSTAT_D1; 2395 break; 2396 case PCI_POWERSTATE_D2: 2397 if ((cfg->pp.pp_cap & PCIM_PCAP_D2SUPP) == 0) 2398 return (EOPNOTSUPP); 2399 status |= PCIM_PSTAT_D2; 2400 break; 2401 case PCI_POWERSTATE_D3: 2402 status |= PCIM_PSTAT_D3; 2403 break; 2404 default: 2405 return (EINVAL); 2406 } 2407 2408 if (bootverbose) 2409 pci_printf(cfg, "Transition from D%d to D%d\n", oldstate, 2410 state); 2411 2412 PCI_WRITE_CONFIG(dev, child, cfg->pp.pp_status, status, 2); 2413 if (delay) 2414 DELAY(delay); 2415 return (0); 2416 } 2417 2418 int 2419 pci_get_powerstate_method(device_t dev, device_t child) 2420 { 2421 struct pci_devinfo *dinfo = device_get_ivars(child); 2422 pcicfgregs *cfg = &dinfo->cfg; 2423 uint16_t status; 2424 int result; 2425 2426 if (cfg->pp.pp_cap != 0) { 2427 status = PCI_READ_CONFIG(dev, child, cfg->pp.pp_status, 2); 2428 switch (status & PCIM_PSTAT_DMASK) { 2429 case PCIM_PSTAT_D0: 2430 result = PCI_POWERSTATE_D0; 2431 break; 2432 case PCIM_PSTAT_D1: 2433 result = PCI_POWERSTATE_D1; 2434 break; 2435 case PCIM_PSTAT_D2: 2436 result = PCI_POWERSTATE_D2; 2437 break; 2438 case PCIM_PSTAT_D3: 2439 result = PCI_POWERSTATE_D3; 2440 break; 2441 default: 2442 result = PCI_POWERSTATE_UNKNOWN; 2443 break; 2444 } 2445 } else { 2446 /* No support, device is always at D0 */ 2447 result = PCI_POWERSTATE_D0; 2448 } 2449 return (result); 2450 } 2451 2452 /* 2453 * Some convenience functions for PCI device drivers. 2454 */ 2455 2456 static __inline void 2457 pci_set_command_bit(device_t dev, device_t child, uint16_t bit) 2458 { 2459 uint16_t command; 2460 2461 command = PCI_READ_CONFIG(dev, child, PCIR_COMMAND, 2); 2462 command |= bit; 2463 PCI_WRITE_CONFIG(dev, child, PCIR_COMMAND, command, 2); 2464 } 2465 2466 static __inline void 2467 pci_clear_command_bit(device_t dev, device_t child, uint16_t bit) 2468 { 2469 uint16_t command; 2470 2471 command = PCI_READ_CONFIG(dev, child, PCIR_COMMAND, 2); 2472 command &= ~bit; 2473 PCI_WRITE_CONFIG(dev, child, PCIR_COMMAND, command, 2); 2474 } 2475 2476 int 2477 pci_enable_busmaster_method(device_t dev, device_t child) 2478 { 2479 pci_set_command_bit(dev, child, PCIM_CMD_BUSMASTEREN); 2480 return (0); 2481 } 2482 2483 int 2484 pci_disable_busmaster_method(device_t dev, device_t child) 2485 { 2486 pci_clear_command_bit(dev, child, PCIM_CMD_BUSMASTEREN); 2487 return (0); 2488 } 2489 2490 int 2491 pci_enable_io_method(device_t dev, device_t child, int space) 2492 { 2493 uint16_t bit; 2494 2495 switch(space) { 2496 case SYS_RES_IOPORT: 2497 bit = PCIM_CMD_PORTEN; 2498 break; 2499 case SYS_RES_MEMORY: 2500 bit = PCIM_CMD_MEMEN; 2501 break; 2502 default: 2503 return (EINVAL); 2504 } 2505 pci_set_command_bit(dev, child, bit); 2506 return (0); 2507 } 2508 2509 int 2510 pci_disable_io_method(device_t dev, device_t child, int space) 2511 { 2512 uint16_t bit; 2513 2514 switch(space) { 2515 case SYS_RES_IOPORT: 2516 bit = PCIM_CMD_PORTEN; 2517 break; 2518 case SYS_RES_MEMORY: 2519 bit = PCIM_CMD_MEMEN; 2520 break; 2521 default: 2522 return (EINVAL); 2523 } 2524 pci_clear_command_bit(dev, child, bit); 2525 return (0); 2526 } 2527 2528 /* 2529 * New style pci driver. Parent device is either a pci-host-bridge or a 2530 * pci-pci-bridge. Both kinds are represented by instances of pcib. 2531 */ 2532 2533 void 2534 pci_print_verbose(struct pci_devinfo *dinfo) 2535 { 2536 2537 if (bootverbose) { 2538 pcicfgregs *cfg = &dinfo->cfg; 2539 2540 printf("found->\tvendor=0x%04x, dev=0x%04x, revid=0x%02x\n", 2541 cfg->vendor, cfg->device, cfg->revid); 2542 printf("\tdomain=%d, bus=%d, slot=%d, func=%d\n", 2543 cfg->domain, cfg->bus, cfg->slot, cfg->func); 2544 printf("\tclass=%02x-%02x-%02x, hdrtype=0x%02x, mfdev=%d\n", 2545 cfg->baseclass, cfg->subclass, cfg->progif, cfg->hdrtype, 2546 cfg->mfdev); 2547 printf("\tcmdreg=0x%04x, statreg=0x%04x, cachelnsz=%d (dwords)\n", 2548 cfg->cmdreg, cfg->statreg, cfg->cachelnsz); 2549 printf("\tlattimer=0x%02x (%d ns), mingnt=0x%02x (%d ns), maxlat=0x%02x (%d ns)\n", 2550 cfg->lattimer, cfg->lattimer * 30, cfg->mingnt, 2551 cfg->mingnt * 250, cfg->maxlat, cfg->maxlat * 250); 2552 if (cfg->intpin > 0) 2553 printf("\tintpin=%c, irq=%d\n", 2554 cfg->intpin +'a' -1, cfg->intline); 2555 if (cfg->pp.pp_cap) { 2556 uint16_t status; 2557 2558 status = pci_read_config(cfg->dev, cfg->pp.pp_status, 2); 2559 printf("\tpowerspec %d supports D0%s%s D3 current D%d\n", 2560 cfg->pp.pp_cap & PCIM_PCAP_SPEC, 2561 cfg->pp.pp_cap & PCIM_PCAP_D1SUPP ? " D1" : "", 2562 cfg->pp.pp_cap & PCIM_PCAP_D2SUPP ? " D2" : "", 2563 status & PCIM_PSTAT_DMASK); 2564 } 2565 if (cfg->msi.msi_location) { 2566 int ctrl; 2567 2568 ctrl = cfg->msi.msi_ctrl; 2569 printf("\tMSI supports %d message%s%s%s\n", 2570 cfg->msi.msi_msgnum, 2571 (cfg->msi.msi_msgnum == 1) ? "" : "s", 2572 (ctrl & PCIM_MSICTRL_64BIT) ? ", 64 bit" : "", 2573 (ctrl & PCIM_MSICTRL_VECTOR) ? ", vector masks":""); 2574 } 2575 if (cfg->msix.msix_location) { 2576 printf("\tMSI-X supports %d message%s ", 2577 cfg->msix.msix_msgnum, 2578 (cfg->msix.msix_msgnum == 1) ? "" : "s"); 2579 if (cfg->msix.msix_table_bar == cfg->msix.msix_pba_bar) 2580 printf("in map 0x%x\n", 2581 cfg->msix.msix_table_bar); 2582 else 2583 printf("in maps 0x%x and 0x%x\n", 2584 cfg->msix.msix_table_bar, 2585 cfg->msix.msix_pba_bar); 2586 } 2587 } 2588 } 2589 2590 static int 2591 pci_porten(device_t dev) 2592 { 2593 return (pci_read_config(dev, PCIR_COMMAND, 2) & PCIM_CMD_PORTEN) != 0; 2594 } 2595 2596 static int 2597 pci_memen(device_t dev) 2598 { 2599 return (pci_read_config(dev, PCIR_COMMAND, 2) & PCIM_CMD_MEMEN) != 0; 2600 } 2601 2602 static void 2603 pci_read_bar(device_t dev, int reg, pci_addr_t *mapp, pci_addr_t *testvalp) 2604 { 2605 struct pci_devinfo *dinfo; 2606 pci_addr_t map, testval; 2607 int ln2range; 2608 uint16_t cmd; 2609 2610 /* 2611 * The device ROM BAR is special. It is always a 32-bit 2612 * memory BAR. Bit 0 is special and should not be set when 2613 * sizing the BAR. 2614 */ 2615 dinfo = device_get_ivars(dev); 2616 if (PCIR_IS_BIOS(&dinfo->cfg, reg)) { 2617 map = pci_read_config(dev, reg, 4); 2618 pci_write_config(dev, reg, 0xfffffffe, 4); 2619 testval = pci_read_config(dev, reg, 4); 2620 pci_write_config(dev, reg, map, 4); 2621 *mapp = map; 2622 *testvalp = testval; 2623 return; 2624 } 2625 2626 map = pci_read_config(dev, reg, 4); 2627 ln2range = pci_maprange(map); 2628 if (ln2range == 64) 2629 map |= (pci_addr_t)pci_read_config(dev, reg + 4, 4) << 32; 2630 2631 /* 2632 * Disable decoding via the command register before 2633 * determining the BAR's length since we will be placing it in 2634 * a weird state. 2635 */ 2636 cmd = pci_read_config(dev, PCIR_COMMAND, 2); 2637 pci_write_config(dev, PCIR_COMMAND, 2638 cmd & ~(PCI_BAR_MEM(map) ? PCIM_CMD_MEMEN : PCIM_CMD_PORTEN), 2); 2639 2640 /* 2641 * Determine the BAR's length by writing all 1's. The bottom 2642 * log_2(size) bits of the BAR will stick as 0 when we read 2643 * the value back. 2644 */ 2645 pci_write_config(dev, reg, 0xffffffff, 4); 2646 testval = pci_read_config(dev, reg, 4); 2647 if (ln2range == 64) { 2648 pci_write_config(dev, reg + 4, 0xffffffff, 4); 2649 testval |= (pci_addr_t)pci_read_config(dev, reg + 4, 4) << 32; 2650 } 2651 2652 /* 2653 * Restore the original value of the BAR. We may have reprogrammed 2654 * the BAR of the low-level console device and when booting verbose, 2655 * we need the console device addressable. 2656 */ 2657 pci_write_config(dev, reg, map, 4); 2658 if (ln2range == 64) 2659 pci_write_config(dev, reg + 4, map >> 32, 4); 2660 pci_write_config(dev, PCIR_COMMAND, cmd, 2); 2661 2662 *mapp = map; 2663 *testvalp = testval; 2664 } 2665 2666 static void 2667 pci_write_bar(device_t dev, struct pci_map *pm, pci_addr_t base) 2668 { 2669 struct pci_devinfo *dinfo; 2670 int ln2range; 2671 2672 /* The device ROM BAR is always a 32-bit memory BAR. */ 2673 dinfo = device_get_ivars(dev); 2674 if (PCIR_IS_BIOS(&dinfo->cfg, pm->pm_reg)) 2675 ln2range = 32; 2676 else 2677 ln2range = pci_maprange(pm->pm_value); 2678 pci_write_config(dev, pm->pm_reg, base, 4); 2679 if (ln2range == 64) 2680 pci_write_config(dev, pm->pm_reg + 4, base >> 32, 4); 2681 pm->pm_value = pci_read_config(dev, pm->pm_reg, 4); 2682 if (ln2range == 64) 2683 pm->pm_value |= (pci_addr_t)pci_read_config(dev, 2684 pm->pm_reg + 4, 4) << 32; 2685 } 2686 2687 struct pci_map * 2688 pci_find_bar(device_t dev, int reg) 2689 { 2690 struct pci_devinfo *dinfo; 2691 struct pci_map *pm; 2692 2693 dinfo = device_get_ivars(dev); 2694 STAILQ_FOREACH(pm, &dinfo->cfg.maps, pm_link) { 2695 if (pm->pm_reg == reg) 2696 return (pm); 2697 } 2698 return (NULL); 2699 } 2700 2701 int 2702 pci_bar_enabled(device_t dev, struct pci_map *pm) 2703 { 2704 struct pci_devinfo *dinfo; 2705 uint16_t cmd; 2706 2707 dinfo = device_get_ivars(dev); 2708 if (PCIR_IS_BIOS(&dinfo->cfg, pm->pm_reg) && 2709 !(pm->pm_value & PCIM_BIOS_ENABLE)) 2710 return (0); 2711 cmd = pci_read_config(dev, PCIR_COMMAND, 2); 2712 if (PCIR_IS_BIOS(&dinfo->cfg, pm->pm_reg) || PCI_BAR_MEM(pm->pm_value)) 2713 return ((cmd & PCIM_CMD_MEMEN) != 0); 2714 else 2715 return ((cmd & PCIM_CMD_PORTEN) != 0); 2716 } 2717 2718 static struct pci_map * 2719 pci_add_bar(device_t dev, int reg, pci_addr_t value, pci_addr_t size) 2720 { 2721 struct pci_devinfo *dinfo; 2722 struct pci_map *pm, *prev; 2723 2724 dinfo = device_get_ivars(dev); 2725 pm = malloc(sizeof(*pm), M_DEVBUF, M_WAITOK | M_ZERO); 2726 pm->pm_reg = reg; 2727 pm->pm_value = value; 2728 pm->pm_size = size; 2729 STAILQ_FOREACH(prev, &dinfo->cfg.maps, pm_link) { 2730 KASSERT(prev->pm_reg != pm->pm_reg, ("duplicate map %02x", 2731 reg)); 2732 if (STAILQ_NEXT(prev, pm_link) == NULL || 2733 STAILQ_NEXT(prev, pm_link)->pm_reg > pm->pm_reg) 2734 break; 2735 } 2736 if (prev != NULL) 2737 STAILQ_INSERT_AFTER(&dinfo->cfg.maps, prev, pm, pm_link); 2738 else 2739 STAILQ_INSERT_TAIL(&dinfo->cfg.maps, pm, pm_link); 2740 return (pm); 2741 } 2742 2743 static void 2744 pci_restore_bars(device_t dev) 2745 { 2746 struct pci_devinfo *dinfo; 2747 struct pci_map *pm; 2748 int ln2range; 2749 2750 dinfo = device_get_ivars(dev); 2751 STAILQ_FOREACH(pm, &dinfo->cfg.maps, pm_link) { 2752 if (PCIR_IS_BIOS(&dinfo->cfg, pm->pm_reg)) 2753 ln2range = 32; 2754 else 2755 ln2range = pci_maprange(pm->pm_value); 2756 pci_write_config(dev, pm->pm_reg, pm->pm_value, 4); 2757 if (ln2range == 64) 2758 pci_write_config(dev, pm->pm_reg + 4, 2759 pm->pm_value >> 32, 4); 2760 } 2761 } 2762 2763 /* 2764 * Add a resource based on a pci map register. Return 1 if the map 2765 * register is a 32bit map register or 2 if it is a 64bit register. 2766 */ 2767 static int 2768 pci_add_map(device_t bus, device_t dev, int reg, struct resource_list *rl, 2769 int force, int prefetch) 2770 { 2771 struct pci_map *pm; 2772 pci_addr_t base, map, testval; 2773 pci_addr_t start, end, count; 2774 int barlen, basezero, flags, maprange, mapsize, type; 2775 uint16_t cmd; 2776 struct resource *res; 2777 2778 /* 2779 * The BAR may already exist if the device is a CardBus card 2780 * whose CIS is stored in this BAR. 2781 */ 2782 pm = pci_find_bar(dev, reg); 2783 if (pm != NULL) { 2784 maprange = pci_maprange(pm->pm_value); 2785 barlen = maprange == 64 ? 2 : 1; 2786 return (barlen); 2787 } 2788 2789 pci_read_bar(dev, reg, &map, &testval); 2790 if (PCI_BAR_MEM(map)) { 2791 type = SYS_RES_MEMORY; 2792 if (map & PCIM_BAR_MEM_PREFETCH) 2793 prefetch = 1; 2794 } else 2795 type = SYS_RES_IOPORT; 2796 mapsize = pci_mapsize(testval); 2797 base = pci_mapbase(map); 2798 #ifdef __PCI_BAR_ZERO_VALID 2799 basezero = 0; 2800 #else 2801 basezero = base == 0; 2802 #endif 2803 maprange = pci_maprange(map); 2804 barlen = maprange == 64 ? 2 : 1; 2805 2806 /* 2807 * For I/O registers, if bottom bit is set, and the next bit up 2808 * isn't clear, we know we have a BAR that doesn't conform to the 2809 * spec, so ignore it. Also, sanity check the size of the data 2810 * areas to the type of memory involved. Memory must be at least 2811 * 16 bytes in size, while I/O ranges must be at least 4. 2812 */ 2813 if (PCI_BAR_IO(testval) && (testval & PCIM_BAR_IO_RESERVED) != 0) 2814 return (barlen); 2815 if ((type == SYS_RES_MEMORY && mapsize < 4) || 2816 (type == SYS_RES_IOPORT && mapsize < 2)) 2817 return (barlen); 2818 2819 /* Save a record of this BAR. */ 2820 pm = pci_add_bar(dev, reg, map, mapsize); 2821 if (bootverbose) { 2822 printf("\tmap[%02x]: type %s, range %2d, base %#jx, size %2d", 2823 reg, pci_maptype(map), maprange, (uintmax_t)base, mapsize); 2824 if (type == SYS_RES_IOPORT && !pci_porten(dev)) 2825 printf(", port disabled\n"); 2826 else if (type == SYS_RES_MEMORY && !pci_memen(dev)) 2827 printf(", memory disabled\n"); 2828 else 2829 printf(", enabled\n"); 2830 } 2831 2832 /* 2833 * If base is 0, then we have problems if this architecture does 2834 * not allow that. It is best to ignore such entries for the 2835 * moment. These will be allocated later if the driver specifically 2836 * requests them. However, some removable busses look better when 2837 * all resources are allocated, so allow '0' to be overriden. 2838 * 2839 * Similarly treat maps whose values is the same as the test value 2840 * read back. These maps have had all f's written to them by the 2841 * BIOS in an attempt to disable the resources. 2842 */ 2843 if (!force && (basezero || map == testval)) 2844 return (barlen); 2845 if ((u_long)base != base) { 2846 device_printf(bus, 2847 "pci%d:%d:%d:%d bar %#x too many address bits", 2848 pci_get_domain(dev), pci_get_bus(dev), pci_get_slot(dev), 2849 pci_get_function(dev), reg); 2850 return (barlen); 2851 } 2852 2853 /* 2854 * This code theoretically does the right thing, but has 2855 * undesirable side effects in some cases where peripherals 2856 * respond oddly to having these bits enabled. Let the user 2857 * be able to turn them off (since pci_enable_io_modes is 1 by 2858 * default). 2859 */ 2860 if (pci_enable_io_modes) { 2861 /* Turn on resources that have been left off by a lazy BIOS */ 2862 if (type == SYS_RES_IOPORT && !pci_porten(dev)) { 2863 cmd = pci_read_config(dev, PCIR_COMMAND, 2); 2864 cmd |= PCIM_CMD_PORTEN; 2865 pci_write_config(dev, PCIR_COMMAND, cmd, 2); 2866 } 2867 if (type == SYS_RES_MEMORY && !pci_memen(dev)) { 2868 cmd = pci_read_config(dev, PCIR_COMMAND, 2); 2869 cmd |= PCIM_CMD_MEMEN; 2870 pci_write_config(dev, PCIR_COMMAND, cmd, 2); 2871 } 2872 } else { 2873 if (type == SYS_RES_IOPORT && !pci_porten(dev)) 2874 return (barlen); 2875 if (type == SYS_RES_MEMORY && !pci_memen(dev)) 2876 return (barlen); 2877 } 2878 2879 count = (pci_addr_t)1 << mapsize; 2880 flags = RF_ALIGNMENT_LOG2(mapsize); 2881 if (prefetch) 2882 flags |= RF_PREFETCHABLE; 2883 if (basezero || base == pci_mapbase(testval) || pci_clear_bars) { 2884 start = 0; /* Let the parent decide. */ 2885 end = ~0ul; 2886 } else { 2887 start = base; 2888 end = base + count - 1; 2889 } 2890 resource_list_add(rl, type, reg, start, end, count); 2891 2892 /* 2893 * Try to allocate the resource for this BAR from our parent 2894 * so that this resource range is already reserved. The 2895 * driver for this device will later inherit this resource in 2896 * pci_alloc_resource(). 2897 */ 2898 res = resource_list_reserve(rl, bus, dev, type, ®, start, end, count, 2899 flags); 2900 if (pci_do_realloc_bars && res == NULL && (start != 0 || end != ~0ul)) { 2901 /* 2902 * If the allocation fails, try to allocate a resource for 2903 * this BAR using any available range. The firmware felt 2904 * it was important enough to assign a resource, so don't 2905 * disable decoding if we can help it. 2906 */ 2907 resource_list_delete(rl, type, reg); 2908 resource_list_add(rl, type, reg, 0, ~0ul, count); 2909 res = resource_list_reserve(rl, bus, dev, type, ®, 0, ~0ul, 2910 count, flags); 2911 } 2912 if (res == NULL) { 2913 /* 2914 * If the allocation fails, delete the resource list entry 2915 * and disable decoding for this device. 2916 * 2917 * If the driver requests this resource in the future, 2918 * pci_reserve_map() will try to allocate a fresh 2919 * resource range. 2920 */ 2921 resource_list_delete(rl, type, reg); 2922 pci_disable_io(dev, type); 2923 if (bootverbose) 2924 device_printf(bus, 2925 "pci%d:%d:%d:%d bar %#x failed to allocate\n", 2926 pci_get_domain(dev), pci_get_bus(dev), 2927 pci_get_slot(dev), pci_get_function(dev), reg); 2928 } else { 2929 start = rman_get_start(res); 2930 pci_write_bar(dev, pm, start); 2931 } 2932 return (barlen); 2933 } 2934 2935 /* 2936 * For ATA devices we need to decide early what addressing mode to use. 2937 * Legacy demands that the primary and secondary ATA ports sits on the 2938 * same addresses that old ISA hardware did. This dictates that we use 2939 * those addresses and ignore the BAR's if we cannot set PCI native 2940 * addressing mode. 2941 */ 2942 static void 2943 pci_ata_maps(device_t bus, device_t dev, struct resource_list *rl, int force, 2944 uint32_t prefetchmask) 2945 { 2946 struct resource *r; 2947 int rid, type, progif; 2948 #if 0 2949 /* if this device supports PCI native addressing use it */ 2950 progif = pci_read_config(dev, PCIR_PROGIF, 1); 2951 if ((progif & 0x8a) == 0x8a) { 2952 if (pci_mapbase(pci_read_config(dev, PCIR_BAR(0), 4)) && 2953 pci_mapbase(pci_read_config(dev, PCIR_BAR(2), 4))) { 2954 printf("Trying ATA native PCI addressing mode\n"); 2955 pci_write_config(dev, PCIR_PROGIF, progif | 0x05, 1); 2956 } 2957 } 2958 #endif 2959 progif = pci_read_config(dev, PCIR_PROGIF, 1); 2960 type = SYS_RES_IOPORT; 2961 if (progif & PCIP_STORAGE_IDE_MODEPRIM) { 2962 pci_add_map(bus, dev, PCIR_BAR(0), rl, force, 2963 prefetchmask & (1 << 0)); 2964 pci_add_map(bus, dev, PCIR_BAR(1), rl, force, 2965 prefetchmask & (1 << 1)); 2966 } else { 2967 rid = PCIR_BAR(0); 2968 resource_list_add(rl, type, rid, 0x1f0, 0x1f7, 8); 2969 r = resource_list_reserve(rl, bus, dev, type, &rid, 0x1f0, 2970 0x1f7, 8, 0); 2971 rid = PCIR_BAR(1); 2972 resource_list_add(rl, type, rid, 0x3f6, 0x3f6, 1); 2973 r = resource_list_reserve(rl, bus, dev, type, &rid, 0x3f6, 2974 0x3f6, 1, 0); 2975 } 2976 if (progif & PCIP_STORAGE_IDE_MODESEC) { 2977 pci_add_map(bus, dev, PCIR_BAR(2), rl, force, 2978 prefetchmask & (1 << 2)); 2979 pci_add_map(bus, dev, PCIR_BAR(3), rl, force, 2980 prefetchmask & (1 << 3)); 2981 } else { 2982 rid = PCIR_BAR(2); 2983 resource_list_add(rl, type, rid, 0x170, 0x177, 8); 2984 r = resource_list_reserve(rl, bus, dev, type, &rid, 0x170, 2985 0x177, 8, 0); 2986 rid = PCIR_BAR(3); 2987 resource_list_add(rl, type, rid, 0x376, 0x376, 1); 2988 r = resource_list_reserve(rl, bus, dev, type, &rid, 0x376, 2989 0x376, 1, 0); 2990 } 2991 pci_add_map(bus, dev, PCIR_BAR(4), rl, force, 2992 prefetchmask & (1 << 4)); 2993 pci_add_map(bus, dev, PCIR_BAR(5), rl, force, 2994 prefetchmask & (1 << 5)); 2995 } 2996 2997 static void 2998 pci_assign_interrupt(device_t bus, device_t dev, int force_route) 2999 { 3000 struct pci_devinfo *dinfo = device_get_ivars(dev); 3001 pcicfgregs *cfg = &dinfo->cfg; 3002 char tunable_name[64]; 3003 int irq; 3004 3005 /* Has to have an intpin to have an interrupt. */ 3006 if (cfg->intpin == 0) 3007 return; 3008 3009 /* Let the user override the IRQ with a tunable. */ 3010 irq = PCI_INVALID_IRQ; 3011 snprintf(tunable_name, sizeof(tunable_name), 3012 "hw.pci%d.%d.%d.INT%c.irq", 3013 cfg->domain, cfg->bus, cfg->slot, cfg->intpin + 'A' - 1); 3014 if (TUNABLE_INT_FETCH(tunable_name, &irq) && (irq >= 255 || irq <= 0)) 3015 irq = PCI_INVALID_IRQ; 3016 3017 /* 3018 * If we didn't get an IRQ via the tunable, then we either use the 3019 * IRQ value in the intline register or we ask the bus to route an 3020 * interrupt for us. If force_route is true, then we only use the 3021 * value in the intline register if the bus was unable to assign an 3022 * IRQ. 3023 */ 3024 if (!PCI_INTERRUPT_VALID(irq)) { 3025 if (!PCI_INTERRUPT_VALID(cfg->intline) || force_route) 3026 irq = PCI_ASSIGN_INTERRUPT(bus, dev); 3027 if (!PCI_INTERRUPT_VALID(irq)) 3028 irq = cfg->intline; 3029 } 3030 3031 /* If after all that we don't have an IRQ, just bail. */ 3032 if (!PCI_INTERRUPT_VALID(irq)) 3033 return; 3034 3035 /* Update the config register if it changed. */ 3036 if (irq != cfg->intline) { 3037 cfg->intline = irq; 3038 pci_write_config(dev, PCIR_INTLINE, irq, 1); 3039 } 3040 3041 /* Add this IRQ as rid 0 interrupt resource. */ 3042 resource_list_add(&dinfo->resources, SYS_RES_IRQ, 0, irq, irq, 1); 3043 } 3044 3045 /* Perform early OHCI takeover from SMM. */ 3046 static void 3047 ohci_early_takeover(device_t self) 3048 { 3049 struct resource *res; 3050 uint32_t ctl; 3051 int rid; 3052 int i; 3053 3054 rid = PCIR_BAR(0); 3055 res = bus_alloc_resource_any(self, SYS_RES_MEMORY, &rid, RF_ACTIVE); 3056 if (res == NULL) 3057 return; 3058 3059 ctl = bus_read_4(res, OHCI_CONTROL); 3060 if (ctl & OHCI_IR) { 3061 if (bootverbose) 3062 printf("ohci early: " 3063 "SMM active, request owner change\n"); 3064 bus_write_4(res, OHCI_COMMAND_STATUS, OHCI_OCR); 3065 for (i = 0; (i < 100) && (ctl & OHCI_IR); i++) { 3066 DELAY(1000); 3067 ctl = bus_read_4(res, OHCI_CONTROL); 3068 } 3069 if (ctl & OHCI_IR) { 3070 if (bootverbose) 3071 printf("ohci early: " 3072 "SMM does not respond, resetting\n"); 3073 bus_write_4(res, OHCI_CONTROL, OHCI_HCFS_RESET); 3074 } 3075 /* Disable interrupts */ 3076 bus_write_4(res, OHCI_INTERRUPT_DISABLE, OHCI_ALL_INTRS); 3077 } 3078 3079 bus_release_resource(self, SYS_RES_MEMORY, rid, res); 3080 } 3081 3082 /* Perform early UHCI takeover from SMM. */ 3083 static void 3084 uhci_early_takeover(device_t self) 3085 { 3086 struct resource *res; 3087 int rid; 3088 3089 /* 3090 * Set the PIRQD enable bit and switch off all the others. We don't 3091 * want legacy support to interfere with us XXX Does this also mean 3092 * that the BIOS won't touch the keyboard anymore if it is connected 3093 * to the ports of the root hub? 3094 */ 3095 pci_write_config(self, PCI_LEGSUP, PCI_LEGSUP_USBPIRQDEN, 2); 3096 3097 /* Disable interrupts */ 3098 rid = PCI_UHCI_BASE_REG; 3099 res = bus_alloc_resource_any(self, SYS_RES_IOPORT, &rid, RF_ACTIVE); 3100 if (res != NULL) { 3101 bus_write_2(res, UHCI_INTR, 0); 3102 bus_release_resource(self, SYS_RES_IOPORT, rid, res); 3103 } 3104 } 3105 3106 /* Perform early EHCI takeover from SMM. */ 3107 static void 3108 ehci_early_takeover(device_t self) 3109 { 3110 struct resource *res; 3111 uint32_t cparams; 3112 uint32_t eec; 3113 uint8_t eecp; 3114 uint8_t bios_sem; 3115 uint8_t offs; 3116 int rid; 3117 int i; 3118 3119 rid = PCIR_BAR(0); 3120 res = bus_alloc_resource_any(self, SYS_RES_MEMORY, &rid, RF_ACTIVE); 3121 if (res == NULL) 3122 return; 3123 3124 cparams = bus_read_4(res, EHCI_HCCPARAMS); 3125 3126 /* Synchronise with the BIOS if it owns the controller. */ 3127 for (eecp = EHCI_HCC_EECP(cparams); eecp != 0; 3128 eecp = EHCI_EECP_NEXT(eec)) { 3129 eec = pci_read_config(self, eecp, 4); 3130 if (EHCI_EECP_ID(eec) != EHCI_EC_LEGSUP) { 3131 continue; 3132 } 3133 bios_sem = pci_read_config(self, eecp + 3134 EHCI_LEGSUP_BIOS_SEM, 1); 3135 if (bios_sem == 0) { 3136 continue; 3137 } 3138 if (bootverbose) 3139 printf("ehci early: " 3140 "SMM active, request owner change\n"); 3141 3142 pci_write_config(self, eecp + EHCI_LEGSUP_OS_SEM, 1, 1); 3143 3144 for (i = 0; (i < 100) && (bios_sem != 0); i++) { 3145 DELAY(1000); 3146 bios_sem = pci_read_config(self, eecp + 3147 EHCI_LEGSUP_BIOS_SEM, 1); 3148 } 3149 3150 if (bios_sem != 0) { 3151 if (bootverbose) 3152 printf("ehci early: " 3153 "SMM does not respond\n"); 3154 } 3155 /* Disable interrupts */ 3156 offs = EHCI_CAPLENGTH(bus_read_4(res, EHCI_CAPLEN_HCIVERSION)); 3157 bus_write_4(res, offs + EHCI_USBINTR, 0); 3158 } 3159 bus_release_resource(self, SYS_RES_MEMORY, rid, res); 3160 } 3161 3162 /* Perform early XHCI takeover from SMM. */ 3163 static void 3164 xhci_early_takeover(device_t self) 3165 { 3166 struct resource *res; 3167 uint32_t cparams; 3168 uint32_t eec; 3169 uint8_t eecp; 3170 uint8_t bios_sem; 3171 uint8_t offs; 3172 int rid; 3173 int i; 3174 3175 rid = PCIR_BAR(0); 3176 res = bus_alloc_resource_any(self, SYS_RES_MEMORY, &rid, RF_ACTIVE); 3177 if (res == NULL) 3178 return; 3179 3180 cparams = bus_read_4(res, XHCI_HCSPARAMS0); 3181 3182 eec = -1; 3183 3184 /* Synchronise with the BIOS if it owns the controller. */ 3185 for (eecp = XHCI_HCS0_XECP(cparams) << 2; eecp != 0 && XHCI_XECP_NEXT(eec); 3186 eecp += XHCI_XECP_NEXT(eec) << 2) { 3187 eec = bus_read_4(res, eecp); 3188 3189 if (XHCI_XECP_ID(eec) != XHCI_ID_USB_LEGACY) 3190 continue; 3191 3192 bios_sem = bus_read_1(res, eecp + XHCI_XECP_BIOS_SEM); 3193 if (bios_sem == 0) 3194 continue; 3195 3196 if (bootverbose) 3197 printf("xhci early: " 3198 "SMM active, request owner change\n"); 3199 3200 bus_write_1(res, eecp + XHCI_XECP_OS_SEM, 1); 3201 3202 /* wait a maximum of 5 second */ 3203 3204 for (i = 0; (i < 5000) && (bios_sem != 0); i++) { 3205 DELAY(1000); 3206 bios_sem = bus_read_1(res, eecp + 3207 XHCI_XECP_BIOS_SEM); 3208 } 3209 3210 if (bios_sem != 0) { 3211 if (bootverbose) 3212 printf("xhci early: " 3213 "SMM does not respond\n"); 3214 } 3215 3216 /* Disable interrupts */ 3217 offs = bus_read_1(res, XHCI_CAPLENGTH); 3218 bus_write_4(res, offs + XHCI_USBCMD, 0); 3219 bus_read_4(res, offs + XHCI_USBSTS); 3220 } 3221 bus_release_resource(self, SYS_RES_MEMORY, rid, res); 3222 } 3223 3224 #if defined(NEW_PCIB) && defined(PCI_RES_BUS) 3225 static void 3226 pci_reserve_secbus(device_t bus, device_t dev, pcicfgregs *cfg, 3227 struct resource_list *rl) 3228 { 3229 struct resource *res; 3230 char *cp; 3231 u_long start, end, count; 3232 int rid, sec_bus, sec_reg, sub_bus, sub_reg, sup_bus; 3233 3234 switch (cfg->hdrtype & PCIM_HDRTYPE) { 3235 case PCIM_HDRTYPE_BRIDGE: 3236 sec_reg = PCIR_SECBUS_1; 3237 sub_reg = PCIR_SUBBUS_1; 3238 break; 3239 case PCIM_HDRTYPE_CARDBUS: 3240 sec_reg = PCIR_SECBUS_2; 3241 sub_reg = PCIR_SUBBUS_2; 3242 break; 3243 default: 3244 return; 3245 } 3246 3247 /* 3248 * If the existing bus range is valid, attempt to reserve it 3249 * from our parent. If this fails for any reason, clear the 3250 * secbus and subbus registers. 3251 * 3252 * XXX: Should we reset sub_bus to sec_bus if it is < sec_bus? 3253 * This would at least preserve the existing sec_bus if it is 3254 * valid. 3255 */ 3256 sec_bus = PCI_READ_CONFIG(bus, dev, sec_reg, 1); 3257 sub_bus = PCI_READ_CONFIG(bus, dev, sub_reg, 1); 3258 3259 /* Quirk handling. */ 3260 switch (pci_get_devid(dev)) { 3261 case 0x12258086: /* Intel 82454KX/GX (Orion) */ 3262 sup_bus = pci_read_config(dev, 0x41, 1); 3263 if (sup_bus != 0xff) { 3264 sec_bus = sup_bus + 1; 3265 sub_bus = sup_bus + 1; 3266 PCI_WRITE_CONFIG(bus, dev, sec_reg, sec_bus, 1); 3267 PCI_WRITE_CONFIG(bus, dev, sub_reg, sub_bus, 1); 3268 } 3269 break; 3270 3271 case 0x00dd10de: 3272 /* Compaq R3000 BIOS sets wrong subordinate bus number. */ 3273 if ((cp = kern_getenv("smbios.planar.maker")) == NULL) 3274 break; 3275 if (strncmp(cp, "Compal", 6) != 0) { 3276 freeenv(cp); 3277 break; 3278 } 3279 freeenv(cp); 3280 if ((cp = kern_getenv("smbios.planar.product")) == NULL) 3281 break; 3282 if (strncmp(cp, "08A0", 4) != 0) { 3283 freeenv(cp); 3284 break; 3285 } 3286 freeenv(cp); 3287 if (sub_bus < 0xa) { 3288 sub_bus = 0xa; 3289 PCI_WRITE_CONFIG(bus, dev, sub_reg, sub_bus, 1); 3290 } 3291 break; 3292 } 3293 3294 if (bootverbose) 3295 printf("\tsecbus=%d, subbus=%d\n", sec_bus, sub_bus); 3296 if (sec_bus > 0 && sub_bus >= sec_bus) { 3297 start = sec_bus; 3298 end = sub_bus; 3299 count = end - start + 1; 3300 3301 resource_list_add(rl, PCI_RES_BUS, 0, 0ul, ~0ul, count); 3302 3303 /* 3304 * If requested, clear secondary bus registers in 3305 * bridge devices to force a complete renumbering 3306 * rather than reserving the existing range. However, 3307 * preserve the existing size. 3308 */ 3309 if (pci_clear_buses) 3310 goto clear; 3311 3312 rid = 0; 3313 res = resource_list_reserve(rl, bus, dev, PCI_RES_BUS, &rid, 3314 start, end, count, 0); 3315 if (res != NULL) 3316 return; 3317 3318 if (bootverbose) 3319 device_printf(bus, 3320 "pci%d:%d:%d:%d secbus failed to allocate\n", 3321 pci_get_domain(dev), pci_get_bus(dev), 3322 pci_get_slot(dev), pci_get_function(dev)); 3323 } 3324 3325 clear: 3326 PCI_WRITE_CONFIG(bus, dev, sec_reg, 0, 1); 3327 PCI_WRITE_CONFIG(bus, dev, sub_reg, 0, 1); 3328 } 3329 3330 static struct resource * 3331 pci_alloc_secbus(device_t dev, device_t child, int *rid, u_long start, 3332 u_long end, u_long count, u_int flags) 3333 { 3334 struct pci_devinfo *dinfo; 3335 pcicfgregs *cfg; 3336 struct resource_list *rl; 3337 struct resource *res; 3338 int sec_reg, sub_reg; 3339 3340 dinfo = device_get_ivars(child); 3341 cfg = &dinfo->cfg; 3342 rl = &dinfo->resources; 3343 switch (cfg->hdrtype & PCIM_HDRTYPE) { 3344 case PCIM_HDRTYPE_BRIDGE: 3345 sec_reg = PCIR_SECBUS_1; 3346 sub_reg = PCIR_SUBBUS_1; 3347 break; 3348 case PCIM_HDRTYPE_CARDBUS: 3349 sec_reg = PCIR_SECBUS_2; 3350 sub_reg = PCIR_SUBBUS_2; 3351 break; 3352 default: 3353 return (NULL); 3354 } 3355 3356 if (*rid != 0) 3357 return (NULL); 3358 3359 if (resource_list_find(rl, PCI_RES_BUS, *rid) == NULL) 3360 resource_list_add(rl, PCI_RES_BUS, *rid, start, end, count); 3361 if (!resource_list_reserved(rl, PCI_RES_BUS, *rid)) { 3362 res = resource_list_reserve(rl, dev, child, PCI_RES_BUS, rid, 3363 start, end, count, flags & ~RF_ACTIVE); 3364 if (res == NULL) { 3365 resource_list_delete(rl, PCI_RES_BUS, *rid); 3366 device_printf(child, "allocating %lu bus%s failed\n", 3367 count, count == 1 ? "" : "es"); 3368 return (NULL); 3369 } 3370 if (bootverbose) 3371 device_printf(child, 3372 "Lazy allocation of %lu bus%s at %lu\n", count, 3373 count == 1 ? "" : "es", rman_get_start(res)); 3374 PCI_WRITE_CONFIG(dev, child, sec_reg, rman_get_start(res), 1); 3375 PCI_WRITE_CONFIG(dev, child, sub_reg, rman_get_end(res), 1); 3376 } 3377 return (resource_list_alloc(rl, dev, child, PCI_RES_BUS, rid, start, 3378 end, count, flags)); 3379 } 3380 #endif 3381 3382 void 3383 pci_add_resources(device_t bus, device_t dev, int force, uint32_t prefetchmask) 3384 { 3385 struct pci_devinfo *dinfo; 3386 pcicfgregs *cfg; 3387 struct resource_list *rl; 3388 const struct pci_quirk *q; 3389 uint32_t devid; 3390 int i; 3391 3392 dinfo = device_get_ivars(dev); 3393 cfg = &dinfo->cfg; 3394 rl = &dinfo->resources; 3395 devid = (cfg->device << 16) | cfg->vendor; 3396 3397 /* ATA devices needs special map treatment */ 3398 if ((pci_get_class(dev) == PCIC_STORAGE) && 3399 (pci_get_subclass(dev) == PCIS_STORAGE_IDE) && 3400 ((pci_get_progif(dev) & PCIP_STORAGE_IDE_MASTERDEV) || 3401 (!pci_read_config(dev, PCIR_BAR(0), 4) && 3402 !pci_read_config(dev, PCIR_BAR(2), 4))) ) 3403 pci_ata_maps(bus, dev, rl, force, prefetchmask); 3404 else 3405 for (i = 0; i < cfg->nummaps;) { 3406 /* 3407 * Skip quirked resources. 3408 */ 3409 for (q = &pci_quirks[0]; q->devid != 0; q++) 3410 if (q->devid == devid && 3411 q->type == PCI_QUIRK_UNMAP_REG && 3412 q->arg1 == PCIR_BAR(i)) 3413 break; 3414 if (q->devid != 0) { 3415 i++; 3416 continue; 3417 } 3418 i += pci_add_map(bus, dev, PCIR_BAR(i), rl, force, 3419 prefetchmask & (1 << i)); 3420 } 3421 3422 /* 3423 * Add additional, quirked resources. 3424 */ 3425 for (q = &pci_quirks[0]; q->devid != 0; q++) 3426 if (q->devid == devid && q->type == PCI_QUIRK_MAP_REG) 3427 pci_add_map(bus, dev, q->arg1, rl, force, 0); 3428 3429 if (cfg->intpin > 0 && PCI_INTERRUPT_VALID(cfg->intline)) { 3430 #ifdef __PCI_REROUTE_INTERRUPT 3431 /* 3432 * Try to re-route interrupts. Sometimes the BIOS or 3433 * firmware may leave bogus values in these registers. 3434 * If the re-route fails, then just stick with what we 3435 * have. 3436 */ 3437 pci_assign_interrupt(bus, dev, 1); 3438 #else 3439 pci_assign_interrupt(bus, dev, 0); 3440 #endif 3441 } 3442 3443 if (pci_usb_takeover && pci_get_class(dev) == PCIC_SERIALBUS && 3444 pci_get_subclass(dev) == PCIS_SERIALBUS_USB) { 3445 if (pci_get_progif(dev) == PCIP_SERIALBUS_USB_XHCI) 3446 xhci_early_takeover(dev); 3447 else if (pci_get_progif(dev) == PCIP_SERIALBUS_USB_EHCI) 3448 ehci_early_takeover(dev); 3449 else if (pci_get_progif(dev) == PCIP_SERIALBUS_USB_OHCI) 3450 ohci_early_takeover(dev); 3451 else if (pci_get_progif(dev) == PCIP_SERIALBUS_USB_UHCI) 3452 uhci_early_takeover(dev); 3453 } 3454 3455 #if defined(NEW_PCIB) && defined(PCI_RES_BUS) 3456 /* 3457 * Reserve resources for secondary bus ranges behind bridge 3458 * devices. 3459 */ 3460 pci_reserve_secbus(bus, dev, cfg, rl); 3461 #endif 3462 } 3463 3464 static struct pci_devinfo * 3465 pci_identify_function(device_t pcib, device_t dev, int domain, int busno, 3466 int slot, int func, size_t dinfo_size) 3467 { 3468 struct pci_devinfo *dinfo; 3469 3470 dinfo = pci_read_device(pcib, domain, busno, slot, func, dinfo_size); 3471 if (dinfo != NULL) 3472 pci_add_child(dev, dinfo); 3473 3474 return (dinfo); 3475 } 3476 3477 void 3478 pci_add_children(device_t dev, int domain, int busno, size_t dinfo_size) 3479 { 3480 #define REG(n, w) PCIB_READ_CONFIG(pcib, busno, s, f, n, w) 3481 device_t pcib = device_get_parent(dev); 3482 struct pci_devinfo *dinfo; 3483 int maxslots; 3484 int s, f, pcifunchigh; 3485 uint8_t hdrtype; 3486 int first_func; 3487 3488 /* 3489 * Try to detect a device at slot 0, function 0. If it exists, try to 3490 * enable ARI. We must enable ARI before detecting the rest of the 3491 * functions on this bus as ARI changes the set of slots and functions 3492 * that are legal on this bus. 3493 */ 3494 dinfo = pci_identify_function(pcib, dev, domain, busno, 0, 0, 3495 dinfo_size); 3496 if (dinfo != NULL && pci_enable_ari) 3497 PCIB_TRY_ENABLE_ARI(pcib, dinfo->cfg.dev); 3498 3499 /* 3500 * Start looking for new devices on slot 0 at function 1 because we 3501 * just identified the device at slot 0, function 0. 3502 */ 3503 first_func = 1; 3504 3505 KASSERT(dinfo_size >= sizeof(struct pci_devinfo), 3506 ("dinfo_size too small")); 3507 maxslots = PCIB_MAXSLOTS(pcib); 3508 for (s = 0; s <= maxslots; s++, first_func = 0) { 3509 pcifunchigh = 0; 3510 f = 0; 3511 DELAY(1); 3512 hdrtype = REG(PCIR_HDRTYPE, 1); 3513 if ((hdrtype & PCIM_HDRTYPE) > PCI_MAXHDRTYPE) 3514 continue; 3515 if (hdrtype & PCIM_MFDEV) 3516 pcifunchigh = PCIB_MAXFUNCS(pcib); 3517 for (f = first_func; f <= pcifunchigh; f++) 3518 pci_identify_function(pcib, dev, domain, busno, s, f, 3519 dinfo_size); 3520 } 3521 #undef REG 3522 } 3523 3524 void 3525 pci_add_child(device_t bus, struct pci_devinfo *dinfo) 3526 { 3527 dinfo->cfg.dev = device_add_child(bus, NULL, -1); 3528 device_set_ivars(dinfo->cfg.dev, dinfo); 3529 resource_list_init(&dinfo->resources); 3530 pci_cfg_save(dinfo->cfg.dev, dinfo, 0); 3531 pci_cfg_restore(dinfo->cfg.dev, dinfo); 3532 pci_print_verbose(dinfo); 3533 pci_add_resources(bus, dinfo->cfg.dev, 0, 0); 3534 pci_child_added(dinfo->cfg.dev); 3535 } 3536 3537 void 3538 pci_child_added_method(device_t dev, device_t child) 3539 { 3540 3541 } 3542 3543 static int 3544 pci_probe(device_t dev) 3545 { 3546 3547 device_set_desc(dev, "PCI bus"); 3548 3549 /* Allow other subclasses to override this driver. */ 3550 return (BUS_PROBE_GENERIC); 3551 } 3552 3553 int 3554 pci_attach_common(device_t dev) 3555 { 3556 struct pci_softc *sc; 3557 int busno, domain; 3558 #ifdef PCI_DMA_BOUNDARY 3559 int error, tag_valid; 3560 #endif 3561 #ifdef PCI_RES_BUS 3562 int rid; 3563 #endif 3564 3565 sc = device_get_softc(dev); 3566 domain = pcib_get_domain(dev); 3567 busno = pcib_get_bus(dev); 3568 #ifdef PCI_RES_BUS 3569 rid = 0; 3570 sc->sc_bus = bus_alloc_resource(dev, PCI_RES_BUS, &rid, busno, busno, 3571 1, 0); 3572 if (sc->sc_bus == NULL) { 3573 device_printf(dev, "failed to allocate bus number\n"); 3574 return (ENXIO); 3575 } 3576 #endif 3577 if (bootverbose) 3578 device_printf(dev, "domain=%d, physical bus=%d\n", 3579 domain, busno); 3580 #ifdef PCI_DMA_BOUNDARY 3581 tag_valid = 0; 3582 if (device_get_devclass(device_get_parent(device_get_parent(dev))) != 3583 devclass_find("pci")) { 3584 error = bus_dma_tag_create(bus_get_dma_tag(dev), 1, 3585 PCI_DMA_BOUNDARY, BUS_SPACE_MAXADDR, BUS_SPACE_MAXADDR, 3586 NULL, NULL, BUS_SPACE_MAXSIZE, BUS_SPACE_UNRESTRICTED, 3587 BUS_SPACE_MAXSIZE, 0, NULL, NULL, &sc->sc_dma_tag); 3588 if (error) 3589 device_printf(dev, "Failed to create DMA tag: %d\n", 3590 error); 3591 else 3592 tag_valid = 1; 3593 } 3594 if (!tag_valid) 3595 #endif 3596 sc->sc_dma_tag = bus_get_dma_tag(dev); 3597 return (0); 3598 } 3599 3600 static int 3601 pci_attach(device_t dev) 3602 { 3603 int busno, domain, error; 3604 3605 error = pci_attach_common(dev); 3606 if (error) 3607 return (error); 3608 3609 /* 3610 * Since there can be multiple independantly numbered PCI 3611 * busses on systems with multiple PCI domains, we can't use 3612 * the unit number to decide which bus we are probing. We ask 3613 * the parent pcib what our domain and bus numbers are. 3614 */ 3615 domain = pcib_get_domain(dev); 3616 busno = pcib_get_bus(dev); 3617 pci_add_children(dev, domain, busno, sizeof(struct pci_devinfo)); 3618 return (bus_generic_attach(dev)); 3619 } 3620 3621 #ifdef PCI_RES_BUS 3622 static int 3623 pci_detach(device_t dev) 3624 { 3625 struct pci_softc *sc; 3626 int error; 3627 3628 error = bus_generic_detach(dev); 3629 if (error) 3630 return (error); 3631 sc = device_get_softc(dev); 3632 return (bus_release_resource(dev, PCI_RES_BUS, 0, sc->sc_bus)); 3633 } 3634 #endif 3635 3636 static void 3637 pci_set_power_child(device_t dev, device_t child, int state) 3638 { 3639 struct pci_devinfo *dinfo; 3640 int dstate; 3641 3642 /* 3643 * Set the device to the given state. If the firmware suggests 3644 * a different power state, use it instead. If power management 3645 * is not present, the firmware is responsible for managing 3646 * device power. Skip children who aren't attached since they 3647 * are handled separately. 3648 */ 3649 dinfo = device_get_ivars(child); 3650 dstate = state; 3651 if (device_is_attached(child) && 3652 PCIB_POWER_FOR_SLEEP(dev, child, &dstate) == 0) 3653 pci_set_powerstate(child, dstate); 3654 } 3655 3656 int 3657 pci_suspend_child(device_t dev, device_t child) 3658 { 3659 struct pci_devinfo *dinfo; 3660 int error; 3661 3662 dinfo = device_get_ivars(child); 3663 3664 /* 3665 * Save the PCI configuration space for the child and set the 3666 * device in the appropriate power state for this sleep state. 3667 */ 3668 pci_cfg_save(child, dinfo, 0); 3669 3670 /* Suspend devices before potentially powering them down. */ 3671 error = bus_generic_suspend_child(dev, child); 3672 3673 if (error) 3674 return (error); 3675 3676 if (pci_do_power_suspend) 3677 pci_set_power_child(dev, child, PCI_POWERSTATE_D3); 3678 3679 return (0); 3680 } 3681 3682 int 3683 pci_resume_child(device_t dev, device_t child) 3684 { 3685 struct pci_devinfo *dinfo; 3686 3687 if (pci_do_power_resume) 3688 pci_set_power_child(dev, child, PCI_POWERSTATE_D0); 3689 3690 dinfo = device_get_ivars(child); 3691 pci_cfg_restore(child, dinfo); 3692 if (!device_is_attached(child)) 3693 pci_cfg_save(child, dinfo, 1); 3694 3695 bus_generic_resume_child(dev, child); 3696 3697 return (0); 3698 } 3699 3700 int 3701 pci_resume(device_t dev) 3702 { 3703 device_t child, *devlist; 3704 int error, i, numdevs; 3705 3706 if ((error = device_get_children(dev, &devlist, &numdevs)) != 0) 3707 return (error); 3708 3709 /* 3710 * Resume critical devices first, then everything else later. 3711 */ 3712 for (i = 0; i < numdevs; i++) { 3713 child = devlist[i]; 3714 switch (pci_get_class(child)) { 3715 case PCIC_DISPLAY: 3716 case PCIC_MEMORY: 3717 case PCIC_BRIDGE: 3718 case PCIC_BASEPERIPH: 3719 BUS_RESUME_CHILD(dev, child); 3720 break; 3721 } 3722 } 3723 for (i = 0; i < numdevs; i++) { 3724 child = devlist[i]; 3725 switch (pci_get_class(child)) { 3726 case PCIC_DISPLAY: 3727 case PCIC_MEMORY: 3728 case PCIC_BRIDGE: 3729 case PCIC_BASEPERIPH: 3730 break; 3731 default: 3732 BUS_RESUME_CHILD(dev, child); 3733 } 3734 } 3735 free(devlist, M_TEMP); 3736 return (0); 3737 } 3738 3739 static void 3740 pci_load_vendor_data(void) 3741 { 3742 caddr_t data; 3743 void *ptr; 3744 size_t sz; 3745 3746 data = preload_search_by_type("pci_vendor_data"); 3747 if (data != NULL) { 3748 ptr = preload_fetch_addr(data); 3749 sz = preload_fetch_size(data); 3750 if (ptr != NULL && sz != 0) { 3751 pci_vendordata = ptr; 3752 pci_vendordata_size = sz; 3753 /* terminate the database */ 3754 pci_vendordata[pci_vendordata_size] = '\n'; 3755 } 3756 } 3757 } 3758 3759 void 3760 pci_driver_added(device_t dev, driver_t *driver) 3761 { 3762 int numdevs; 3763 device_t *devlist; 3764 device_t child; 3765 struct pci_devinfo *dinfo; 3766 int i; 3767 3768 if (bootverbose) 3769 device_printf(dev, "driver added\n"); 3770 DEVICE_IDENTIFY(driver, dev); 3771 if (device_get_children(dev, &devlist, &numdevs) != 0) 3772 return; 3773 for (i = 0; i < numdevs; i++) { 3774 child = devlist[i]; 3775 if (device_get_state(child) != DS_NOTPRESENT) 3776 continue; 3777 dinfo = device_get_ivars(child); 3778 pci_print_verbose(dinfo); 3779 if (bootverbose) 3780 pci_printf(&dinfo->cfg, "reprobing on driver added\n"); 3781 pci_cfg_restore(child, dinfo); 3782 if (device_probe_and_attach(child) != 0) 3783 pci_child_detached(dev, child); 3784 } 3785 free(devlist, M_TEMP); 3786 } 3787 3788 int 3789 pci_setup_intr(device_t dev, device_t child, struct resource *irq, int flags, 3790 driver_filter_t *filter, driver_intr_t *intr, void *arg, void **cookiep) 3791 { 3792 struct pci_devinfo *dinfo; 3793 struct msix_table_entry *mte; 3794 struct msix_vector *mv; 3795 uint64_t addr; 3796 uint32_t data; 3797 void *cookie; 3798 int error, rid; 3799 3800 error = bus_generic_setup_intr(dev, child, irq, flags, filter, intr, 3801 arg, &cookie); 3802 if (error) 3803 return (error); 3804 3805 /* If this is not a direct child, just bail out. */ 3806 if (device_get_parent(child) != dev) { 3807 *cookiep = cookie; 3808 return(0); 3809 } 3810 3811 rid = rman_get_rid(irq); 3812 if (rid == 0) { 3813 /* Make sure that INTx is enabled */ 3814 pci_clear_command_bit(dev, child, PCIM_CMD_INTxDIS); 3815 } else { 3816 /* 3817 * Check to see if the interrupt is MSI or MSI-X. 3818 * Ask our parent to map the MSI and give 3819 * us the address and data register values. 3820 * If we fail for some reason, teardown the 3821 * interrupt handler. 3822 */ 3823 dinfo = device_get_ivars(child); 3824 if (dinfo->cfg.msi.msi_alloc > 0) { 3825 if (dinfo->cfg.msi.msi_addr == 0) { 3826 KASSERT(dinfo->cfg.msi.msi_handlers == 0, 3827 ("MSI has handlers, but vectors not mapped")); 3828 error = PCIB_MAP_MSI(device_get_parent(dev), 3829 child, rman_get_start(irq), &addr, &data); 3830 if (error) 3831 goto bad; 3832 dinfo->cfg.msi.msi_addr = addr; 3833 dinfo->cfg.msi.msi_data = data; 3834 } 3835 if (dinfo->cfg.msi.msi_handlers == 0) 3836 pci_enable_msi(child, dinfo->cfg.msi.msi_addr, 3837 dinfo->cfg.msi.msi_data); 3838 dinfo->cfg.msi.msi_handlers++; 3839 } else { 3840 KASSERT(dinfo->cfg.msix.msix_alloc > 0, 3841 ("No MSI or MSI-X interrupts allocated")); 3842 KASSERT(rid <= dinfo->cfg.msix.msix_table_len, 3843 ("MSI-X index too high")); 3844 mte = &dinfo->cfg.msix.msix_table[rid - 1]; 3845 KASSERT(mte->mte_vector != 0, ("no message vector")); 3846 mv = &dinfo->cfg.msix.msix_vectors[mte->mte_vector - 1]; 3847 KASSERT(mv->mv_irq == rman_get_start(irq), 3848 ("IRQ mismatch")); 3849 if (mv->mv_address == 0) { 3850 KASSERT(mte->mte_handlers == 0, 3851 ("MSI-X table entry has handlers, but vector not mapped")); 3852 error = PCIB_MAP_MSI(device_get_parent(dev), 3853 child, rman_get_start(irq), &addr, &data); 3854 if (error) 3855 goto bad; 3856 mv->mv_address = addr; 3857 mv->mv_data = data; 3858 } 3859 if (mte->mte_handlers == 0) { 3860 pci_enable_msix(child, rid - 1, mv->mv_address, 3861 mv->mv_data); 3862 pci_unmask_msix(child, rid - 1); 3863 } 3864 mte->mte_handlers++; 3865 } 3866 3867 if (!pci_has_quirk(pci_get_devid(dev), 3868 PCI_QUIRK_MSI_INTX_BUG)) { 3869 /* 3870 * Make sure that INTx is disabled if we are 3871 * using MSI/MSIX 3872 */ 3873 pci_set_command_bit(dev, child, PCIM_CMD_INTxDIS); 3874 } 3875 bad: 3876 if (error) { 3877 (void)bus_generic_teardown_intr(dev, child, irq, 3878 cookie); 3879 return (error); 3880 } 3881 } 3882 *cookiep = cookie; 3883 return (0); 3884 } 3885 3886 int 3887 pci_teardown_intr(device_t dev, device_t child, struct resource *irq, 3888 void *cookie) 3889 { 3890 struct msix_table_entry *mte; 3891 struct resource_list_entry *rle; 3892 struct pci_devinfo *dinfo; 3893 int error, rid; 3894 3895 if (irq == NULL || !(rman_get_flags(irq) & RF_ACTIVE)) 3896 return (EINVAL); 3897 3898 /* If this isn't a direct child, just bail out */ 3899 if (device_get_parent(child) != dev) 3900 return(bus_generic_teardown_intr(dev, child, irq, cookie)); 3901 3902 rid = rman_get_rid(irq); 3903 if (rid == 0) { 3904 /* Mask INTx */ 3905 pci_set_command_bit(dev, child, PCIM_CMD_INTxDIS); 3906 } else { 3907 /* 3908 * Check to see if the interrupt is MSI or MSI-X. If so, 3909 * decrement the appropriate handlers count and mask the 3910 * MSI-X message, or disable MSI messages if the count 3911 * drops to 0. 3912 */ 3913 dinfo = device_get_ivars(child); 3914 rle = resource_list_find(&dinfo->resources, SYS_RES_IRQ, rid); 3915 if (rle->res != irq) 3916 return (EINVAL); 3917 if (dinfo->cfg.msi.msi_alloc > 0) { 3918 KASSERT(rid <= dinfo->cfg.msi.msi_alloc, 3919 ("MSI-X index too high")); 3920 if (dinfo->cfg.msi.msi_handlers == 0) 3921 return (EINVAL); 3922 dinfo->cfg.msi.msi_handlers--; 3923 if (dinfo->cfg.msi.msi_handlers == 0) 3924 pci_disable_msi(child); 3925 } else { 3926 KASSERT(dinfo->cfg.msix.msix_alloc > 0, 3927 ("No MSI or MSI-X interrupts allocated")); 3928 KASSERT(rid <= dinfo->cfg.msix.msix_table_len, 3929 ("MSI-X index too high")); 3930 mte = &dinfo->cfg.msix.msix_table[rid - 1]; 3931 if (mte->mte_handlers == 0) 3932 return (EINVAL); 3933 mte->mte_handlers--; 3934 if (mte->mte_handlers == 0) 3935 pci_mask_msix(child, rid - 1); 3936 } 3937 } 3938 error = bus_generic_teardown_intr(dev, child, irq, cookie); 3939 if (rid > 0) 3940 KASSERT(error == 0, 3941 ("%s: generic teardown failed for MSI/MSI-X", __func__)); 3942 return (error); 3943 } 3944 3945 int 3946 pci_print_child(device_t dev, device_t child) 3947 { 3948 struct pci_devinfo *dinfo; 3949 struct resource_list *rl; 3950 int retval = 0; 3951 3952 dinfo = device_get_ivars(child); 3953 rl = &dinfo->resources; 3954 3955 retval += bus_print_child_header(dev, child); 3956 3957 retval += resource_list_print_type(rl, "port", SYS_RES_IOPORT, "%#lx"); 3958 retval += resource_list_print_type(rl, "mem", SYS_RES_MEMORY, "%#lx"); 3959 retval += resource_list_print_type(rl, "irq", SYS_RES_IRQ, "%ld"); 3960 if (device_get_flags(dev)) 3961 retval += printf(" flags %#x", device_get_flags(dev)); 3962 3963 retval += printf(" at device %d.%d", pci_get_slot(child), 3964 pci_get_function(child)); 3965 3966 retval += bus_print_child_domain(dev, child); 3967 retval += bus_print_child_footer(dev, child); 3968 3969 return (retval); 3970 } 3971 3972 static const struct 3973 { 3974 int class; 3975 int subclass; 3976 int report; /* 0 = bootverbose, 1 = always */ 3977 const char *desc; 3978 } pci_nomatch_tab[] = { 3979 {PCIC_OLD, -1, 1, "old"}, 3980 {PCIC_OLD, PCIS_OLD_NONVGA, 1, "non-VGA display device"}, 3981 {PCIC_OLD, PCIS_OLD_VGA, 1, "VGA-compatible display device"}, 3982 {PCIC_STORAGE, -1, 1, "mass storage"}, 3983 {PCIC_STORAGE, PCIS_STORAGE_SCSI, 1, "SCSI"}, 3984 {PCIC_STORAGE, PCIS_STORAGE_IDE, 1, "ATA"}, 3985 {PCIC_STORAGE, PCIS_STORAGE_FLOPPY, 1, "floppy disk"}, 3986 {PCIC_STORAGE, PCIS_STORAGE_IPI, 1, "IPI"}, 3987 {PCIC_STORAGE, PCIS_STORAGE_RAID, 1, "RAID"}, 3988 {PCIC_STORAGE, PCIS_STORAGE_ATA_ADMA, 1, "ATA (ADMA)"}, 3989 {PCIC_STORAGE, PCIS_STORAGE_SATA, 1, "SATA"}, 3990 {PCIC_STORAGE, PCIS_STORAGE_SAS, 1, "SAS"}, 3991 {PCIC_STORAGE, PCIS_STORAGE_NVM, 1, "NVM"}, 3992 {PCIC_NETWORK, -1, 1, "network"}, 3993 {PCIC_NETWORK, PCIS_NETWORK_ETHERNET, 1, "ethernet"}, 3994 {PCIC_NETWORK, PCIS_NETWORK_TOKENRING, 1, "token ring"}, 3995 {PCIC_NETWORK, PCIS_NETWORK_FDDI, 1, "fddi"}, 3996 {PCIC_NETWORK, PCIS_NETWORK_ATM, 1, "ATM"}, 3997 {PCIC_NETWORK, PCIS_NETWORK_ISDN, 1, "ISDN"}, 3998 {PCIC_DISPLAY, -1, 1, "display"}, 3999 {PCIC_DISPLAY, PCIS_DISPLAY_VGA, 1, "VGA"}, 4000 {PCIC_DISPLAY, PCIS_DISPLAY_XGA, 1, "XGA"}, 4001 {PCIC_DISPLAY, PCIS_DISPLAY_3D, 1, "3D"}, 4002 {PCIC_MULTIMEDIA, -1, 1, "multimedia"}, 4003 {PCIC_MULTIMEDIA, PCIS_MULTIMEDIA_VIDEO, 1, "video"}, 4004 {PCIC_MULTIMEDIA, PCIS_MULTIMEDIA_AUDIO, 1, "audio"}, 4005 {PCIC_MULTIMEDIA, PCIS_MULTIMEDIA_TELE, 1, "telephony"}, 4006 {PCIC_MULTIMEDIA, PCIS_MULTIMEDIA_HDA, 1, "HDA"}, 4007 {PCIC_MEMORY, -1, 1, "memory"}, 4008 {PCIC_MEMORY, PCIS_MEMORY_RAM, 1, "RAM"}, 4009 {PCIC_MEMORY, PCIS_MEMORY_FLASH, 1, "flash"}, 4010 {PCIC_BRIDGE, -1, 1, "bridge"}, 4011 {PCIC_BRIDGE, PCIS_BRIDGE_HOST, 1, "HOST-PCI"}, 4012 {PCIC_BRIDGE, PCIS_BRIDGE_ISA, 1, "PCI-ISA"}, 4013 {PCIC_BRIDGE, PCIS_BRIDGE_EISA, 1, "PCI-EISA"}, 4014 {PCIC_BRIDGE, PCIS_BRIDGE_MCA, 1, "PCI-MCA"}, 4015 {PCIC_BRIDGE, PCIS_BRIDGE_PCI, 1, "PCI-PCI"}, 4016 {PCIC_BRIDGE, PCIS_BRIDGE_PCMCIA, 1, "PCI-PCMCIA"}, 4017 {PCIC_BRIDGE, PCIS_BRIDGE_NUBUS, 1, "PCI-NuBus"}, 4018 {PCIC_BRIDGE, PCIS_BRIDGE_CARDBUS, 1, "PCI-CardBus"}, 4019 {PCIC_BRIDGE, PCIS_BRIDGE_RACEWAY, 1, "PCI-RACEway"}, 4020 {PCIC_SIMPLECOMM, -1, 1, "simple comms"}, 4021 {PCIC_SIMPLECOMM, PCIS_SIMPLECOMM_UART, 1, "UART"}, /* could detect 16550 */ 4022 {PCIC_SIMPLECOMM, PCIS_SIMPLECOMM_PAR, 1, "parallel port"}, 4023 {PCIC_SIMPLECOMM, PCIS_SIMPLECOMM_MULSER, 1, "multiport serial"}, 4024 {PCIC_SIMPLECOMM, PCIS_SIMPLECOMM_MODEM, 1, "generic modem"}, 4025 {PCIC_BASEPERIPH, -1, 0, "base peripheral"}, 4026 {PCIC_BASEPERIPH, PCIS_BASEPERIPH_PIC, 1, "interrupt controller"}, 4027 {PCIC_BASEPERIPH, PCIS_BASEPERIPH_DMA, 1, "DMA controller"}, 4028 {PCIC_BASEPERIPH, PCIS_BASEPERIPH_TIMER, 1, "timer"}, 4029 {PCIC_BASEPERIPH, PCIS_BASEPERIPH_RTC, 1, "realtime clock"}, 4030 {PCIC_BASEPERIPH, PCIS_BASEPERIPH_PCIHOT, 1, "PCI hot-plug controller"}, 4031 {PCIC_BASEPERIPH, PCIS_BASEPERIPH_SDHC, 1, "SD host controller"}, 4032 {PCIC_BASEPERIPH, PCIS_BASEPERIPH_IOMMU, 1, "IOMMU"}, 4033 {PCIC_INPUTDEV, -1, 1, "input device"}, 4034 {PCIC_INPUTDEV, PCIS_INPUTDEV_KEYBOARD, 1, "keyboard"}, 4035 {PCIC_INPUTDEV, PCIS_INPUTDEV_DIGITIZER,1, "digitizer"}, 4036 {PCIC_INPUTDEV, PCIS_INPUTDEV_MOUSE, 1, "mouse"}, 4037 {PCIC_INPUTDEV, PCIS_INPUTDEV_SCANNER, 1, "scanner"}, 4038 {PCIC_INPUTDEV, PCIS_INPUTDEV_GAMEPORT, 1, "gameport"}, 4039 {PCIC_DOCKING, -1, 1, "docking station"}, 4040 {PCIC_PROCESSOR, -1, 1, "processor"}, 4041 {PCIC_SERIALBUS, -1, 1, "serial bus"}, 4042 {PCIC_SERIALBUS, PCIS_SERIALBUS_FW, 1, "FireWire"}, 4043 {PCIC_SERIALBUS, PCIS_SERIALBUS_ACCESS, 1, "AccessBus"}, 4044 {PCIC_SERIALBUS, PCIS_SERIALBUS_SSA, 1, "SSA"}, 4045 {PCIC_SERIALBUS, PCIS_SERIALBUS_USB, 1, "USB"}, 4046 {PCIC_SERIALBUS, PCIS_SERIALBUS_FC, 1, "Fibre Channel"}, 4047 {PCIC_SERIALBUS, PCIS_SERIALBUS_SMBUS, 0, "SMBus"}, 4048 {PCIC_WIRELESS, -1, 1, "wireless controller"}, 4049 {PCIC_WIRELESS, PCIS_WIRELESS_IRDA, 1, "iRDA"}, 4050 {PCIC_WIRELESS, PCIS_WIRELESS_IR, 1, "IR"}, 4051 {PCIC_WIRELESS, PCIS_WIRELESS_RF, 1, "RF"}, 4052 {PCIC_INTELLIIO, -1, 1, "intelligent I/O controller"}, 4053 {PCIC_INTELLIIO, PCIS_INTELLIIO_I2O, 1, "I2O"}, 4054 {PCIC_SATCOM, -1, 1, "satellite communication"}, 4055 {PCIC_SATCOM, PCIS_SATCOM_TV, 1, "sat TV"}, 4056 {PCIC_SATCOM, PCIS_SATCOM_AUDIO, 1, "sat audio"}, 4057 {PCIC_SATCOM, PCIS_SATCOM_VOICE, 1, "sat voice"}, 4058 {PCIC_SATCOM, PCIS_SATCOM_DATA, 1, "sat data"}, 4059 {PCIC_CRYPTO, -1, 1, "encrypt/decrypt"}, 4060 {PCIC_CRYPTO, PCIS_CRYPTO_NETCOMP, 1, "network/computer crypto"}, 4061 {PCIC_CRYPTO, PCIS_CRYPTO_ENTERTAIN, 1, "entertainment crypto"}, 4062 {PCIC_DASP, -1, 0, "dasp"}, 4063 {PCIC_DASP, PCIS_DASP_DPIO, 1, "DPIO module"}, 4064 {0, 0, 0, NULL} 4065 }; 4066 4067 void 4068 pci_probe_nomatch(device_t dev, device_t child) 4069 { 4070 int i, report; 4071 const char *cp, *scp; 4072 char *device; 4073 4074 /* 4075 * Look for a listing for this device in a loaded device database. 4076 */ 4077 report = 1; 4078 if ((device = pci_describe_device(child)) != NULL) { 4079 device_printf(dev, "<%s>", device); 4080 free(device, M_DEVBUF); 4081 } else { 4082 /* 4083 * Scan the class/subclass descriptions for a general 4084 * description. 4085 */ 4086 cp = "unknown"; 4087 scp = NULL; 4088 for (i = 0; pci_nomatch_tab[i].desc != NULL; i++) { 4089 if (pci_nomatch_tab[i].class == pci_get_class(child)) { 4090 if (pci_nomatch_tab[i].subclass == -1) { 4091 cp = pci_nomatch_tab[i].desc; 4092 report = pci_nomatch_tab[i].report; 4093 } else if (pci_nomatch_tab[i].subclass == 4094 pci_get_subclass(child)) { 4095 scp = pci_nomatch_tab[i].desc; 4096 report = pci_nomatch_tab[i].report; 4097 } 4098 } 4099 } 4100 if (report || bootverbose) { 4101 device_printf(dev, "<%s%s%s>", 4102 cp ? cp : "", 4103 ((cp != NULL) && (scp != NULL)) ? ", " : "", 4104 scp ? scp : ""); 4105 } 4106 } 4107 if (report || bootverbose) { 4108 printf(" at device %d.%d (no driver attached)\n", 4109 pci_get_slot(child), pci_get_function(child)); 4110 } 4111 pci_cfg_save(child, device_get_ivars(child), 1); 4112 } 4113 4114 void 4115 pci_child_detached(device_t dev, device_t child) 4116 { 4117 struct pci_devinfo *dinfo; 4118 struct resource_list *rl; 4119 4120 dinfo = device_get_ivars(child); 4121 rl = &dinfo->resources; 4122 4123 /* 4124 * Have to deallocate IRQs before releasing any MSI messages and 4125 * have to release MSI messages before deallocating any memory 4126 * BARs. 4127 */ 4128 if (resource_list_release_active(rl, dev, child, SYS_RES_IRQ) != 0) 4129 pci_printf(&dinfo->cfg, "Device leaked IRQ resources\n"); 4130 if (dinfo->cfg.msi.msi_alloc != 0 || dinfo->cfg.msix.msix_alloc != 0) { 4131 pci_printf(&dinfo->cfg, "Device leaked MSI vectors\n"); 4132 (void)pci_release_msi(child); 4133 } 4134 if (resource_list_release_active(rl, dev, child, SYS_RES_MEMORY) != 0) 4135 pci_printf(&dinfo->cfg, "Device leaked memory resources\n"); 4136 if (resource_list_release_active(rl, dev, child, SYS_RES_IOPORT) != 0) 4137 pci_printf(&dinfo->cfg, "Device leaked I/O resources\n"); 4138 #ifdef PCI_RES_BUS 4139 if (resource_list_release_active(rl, dev, child, PCI_RES_BUS) != 0) 4140 pci_printf(&dinfo->cfg, "Device leaked PCI bus numbers\n"); 4141 #endif 4142 4143 pci_cfg_save(child, dinfo, 1); 4144 } 4145 4146 /* 4147 * Parse the PCI device database, if loaded, and return a pointer to a 4148 * description of the device. 4149 * 4150 * The database is flat text formatted as follows: 4151 * 4152 * Any line not in a valid format is ignored. 4153 * Lines are terminated with newline '\n' characters. 4154 * 4155 * A VENDOR line consists of the 4 digit (hex) vendor code, a TAB, then 4156 * the vendor name. 4157 * 4158 * A DEVICE line is entered immediately below the corresponding VENDOR ID. 4159 * - devices cannot be listed without a corresponding VENDOR line. 4160 * A DEVICE line consists of a TAB, the 4 digit (hex) device code, 4161 * another TAB, then the device name. 4162 */ 4163 4164 /* 4165 * Assuming (ptr) points to the beginning of a line in the database, 4166 * return the vendor or device and description of the next entry. 4167 * The value of (vendor) or (device) inappropriate for the entry type 4168 * is set to -1. Returns nonzero at the end of the database. 4169 * 4170 * Note that this is slightly unrobust in the face of corrupt data; 4171 * we attempt to safeguard against this by spamming the end of the 4172 * database with a newline when we initialise. 4173 */ 4174 static int 4175 pci_describe_parse_line(char **ptr, int *vendor, int *device, char **desc) 4176 { 4177 char *cp = *ptr; 4178 int left; 4179 4180 *device = -1; 4181 *vendor = -1; 4182 **desc = '\0'; 4183 for (;;) { 4184 left = pci_vendordata_size - (cp - pci_vendordata); 4185 if (left <= 0) { 4186 *ptr = cp; 4187 return(1); 4188 } 4189 4190 /* vendor entry? */ 4191 if (*cp != '\t' && 4192 sscanf(cp, "%x\t%80[^\n]", vendor, *desc) == 2) 4193 break; 4194 /* device entry? */ 4195 if (*cp == '\t' && 4196 sscanf(cp, "%x\t%80[^\n]", device, *desc) == 2) 4197 break; 4198 4199 /* skip to next line */ 4200 while (*cp != '\n' && left > 0) { 4201 cp++; 4202 left--; 4203 } 4204 if (*cp == '\n') { 4205 cp++; 4206 left--; 4207 } 4208 } 4209 /* skip to next line */ 4210 while (*cp != '\n' && left > 0) { 4211 cp++; 4212 left--; 4213 } 4214 if (*cp == '\n' && left > 0) 4215 cp++; 4216 *ptr = cp; 4217 return(0); 4218 } 4219 4220 static char * 4221 pci_describe_device(device_t dev) 4222 { 4223 int vendor, device; 4224 char *desc, *vp, *dp, *line; 4225 4226 desc = vp = dp = NULL; 4227 4228 /* 4229 * If we have no vendor data, we can't do anything. 4230 */ 4231 if (pci_vendordata == NULL) 4232 goto out; 4233 4234 /* 4235 * Scan the vendor data looking for this device 4236 */ 4237 line = pci_vendordata; 4238 if ((vp = malloc(80, M_DEVBUF, M_NOWAIT)) == NULL) 4239 goto out; 4240 for (;;) { 4241 if (pci_describe_parse_line(&line, &vendor, &device, &vp)) 4242 goto out; 4243 if (vendor == pci_get_vendor(dev)) 4244 break; 4245 } 4246 if ((dp = malloc(80, M_DEVBUF, M_NOWAIT)) == NULL) 4247 goto out; 4248 for (;;) { 4249 if (pci_describe_parse_line(&line, &vendor, &device, &dp)) { 4250 *dp = 0; 4251 break; 4252 } 4253 if (vendor != -1) { 4254 *dp = 0; 4255 break; 4256 } 4257 if (device == pci_get_device(dev)) 4258 break; 4259 } 4260 if (dp[0] == '\0') 4261 snprintf(dp, 80, "0x%x", pci_get_device(dev)); 4262 if ((desc = malloc(strlen(vp) + strlen(dp) + 3, M_DEVBUF, M_NOWAIT)) != 4263 NULL) 4264 sprintf(desc, "%s, %s", vp, dp); 4265 out: 4266 if (vp != NULL) 4267 free(vp, M_DEVBUF); 4268 if (dp != NULL) 4269 free(dp, M_DEVBUF); 4270 return(desc); 4271 } 4272 4273 int 4274 pci_read_ivar(device_t dev, device_t child, int which, uintptr_t *result) 4275 { 4276 struct pci_devinfo *dinfo; 4277 pcicfgregs *cfg; 4278 4279 dinfo = device_get_ivars(child); 4280 cfg = &dinfo->cfg; 4281 4282 switch (which) { 4283 case PCI_IVAR_ETHADDR: 4284 /* 4285 * The generic accessor doesn't deal with failure, so 4286 * we set the return value, then return an error. 4287 */ 4288 *((uint8_t **) result) = NULL; 4289 return (EINVAL); 4290 case PCI_IVAR_SUBVENDOR: 4291 *result = cfg->subvendor; 4292 break; 4293 case PCI_IVAR_SUBDEVICE: 4294 *result = cfg->subdevice; 4295 break; 4296 case PCI_IVAR_VENDOR: 4297 *result = cfg->vendor; 4298 break; 4299 case PCI_IVAR_DEVICE: 4300 *result = cfg->device; 4301 break; 4302 case PCI_IVAR_DEVID: 4303 *result = (cfg->device << 16) | cfg->vendor; 4304 break; 4305 case PCI_IVAR_CLASS: 4306 *result = cfg->baseclass; 4307 break; 4308 case PCI_IVAR_SUBCLASS: 4309 *result = cfg->subclass; 4310 break; 4311 case PCI_IVAR_PROGIF: 4312 *result = cfg->progif; 4313 break; 4314 case PCI_IVAR_REVID: 4315 *result = cfg->revid; 4316 break; 4317 case PCI_IVAR_INTPIN: 4318 *result = cfg->intpin; 4319 break; 4320 case PCI_IVAR_IRQ: 4321 *result = cfg->intline; 4322 break; 4323 case PCI_IVAR_DOMAIN: 4324 *result = cfg->domain; 4325 break; 4326 case PCI_IVAR_BUS: 4327 *result = cfg->bus; 4328 break; 4329 case PCI_IVAR_SLOT: 4330 *result = cfg->slot; 4331 break; 4332 case PCI_IVAR_FUNCTION: 4333 *result = cfg->func; 4334 break; 4335 case PCI_IVAR_CMDREG: 4336 *result = cfg->cmdreg; 4337 break; 4338 case PCI_IVAR_CACHELNSZ: 4339 *result = cfg->cachelnsz; 4340 break; 4341 case PCI_IVAR_MINGNT: 4342 *result = cfg->mingnt; 4343 break; 4344 case PCI_IVAR_MAXLAT: 4345 *result = cfg->maxlat; 4346 break; 4347 case PCI_IVAR_LATTIMER: 4348 *result = cfg->lattimer; 4349 break; 4350 default: 4351 return (ENOENT); 4352 } 4353 return (0); 4354 } 4355 4356 int 4357 pci_write_ivar(device_t dev, device_t child, int which, uintptr_t value) 4358 { 4359 struct pci_devinfo *dinfo; 4360 4361 dinfo = device_get_ivars(child); 4362 4363 switch (which) { 4364 case PCI_IVAR_INTPIN: 4365 dinfo->cfg.intpin = value; 4366 return (0); 4367 case PCI_IVAR_ETHADDR: 4368 case PCI_IVAR_SUBVENDOR: 4369 case PCI_IVAR_SUBDEVICE: 4370 case PCI_IVAR_VENDOR: 4371 case PCI_IVAR_DEVICE: 4372 case PCI_IVAR_DEVID: 4373 case PCI_IVAR_CLASS: 4374 case PCI_IVAR_SUBCLASS: 4375 case PCI_IVAR_PROGIF: 4376 case PCI_IVAR_REVID: 4377 case PCI_IVAR_IRQ: 4378 case PCI_IVAR_DOMAIN: 4379 case PCI_IVAR_BUS: 4380 case PCI_IVAR_SLOT: 4381 case PCI_IVAR_FUNCTION: 4382 return (EINVAL); /* disallow for now */ 4383 4384 default: 4385 return (ENOENT); 4386 } 4387 } 4388 4389 #include "opt_ddb.h" 4390 #ifdef DDB 4391 #include <ddb/ddb.h> 4392 #include <sys/cons.h> 4393 4394 /* 4395 * List resources based on pci map registers, used for within ddb 4396 */ 4397 4398 DB_SHOW_COMMAND(pciregs, db_pci_dump) 4399 { 4400 struct pci_devinfo *dinfo; 4401 struct devlist *devlist_head; 4402 struct pci_conf *p; 4403 const char *name; 4404 int i, error, none_count; 4405 4406 none_count = 0; 4407 /* get the head of the device queue */ 4408 devlist_head = &pci_devq; 4409 4410 /* 4411 * Go through the list of devices and print out devices 4412 */ 4413 for (error = 0, i = 0, 4414 dinfo = STAILQ_FIRST(devlist_head); 4415 (dinfo != NULL) && (error == 0) && (i < pci_numdevs) && !db_pager_quit; 4416 dinfo = STAILQ_NEXT(dinfo, pci_links), i++) { 4417 4418 /* Populate pd_name and pd_unit */ 4419 name = NULL; 4420 if (dinfo->cfg.dev) 4421 name = device_get_name(dinfo->cfg.dev); 4422 4423 p = &dinfo->conf; 4424 db_printf("%s%d@pci%d:%d:%d:%d:\tclass=0x%06x card=0x%08x " 4425 "chip=0x%08x rev=0x%02x hdr=0x%02x\n", 4426 (name && *name) ? name : "none", 4427 (name && *name) ? (int)device_get_unit(dinfo->cfg.dev) : 4428 none_count++, 4429 p->pc_sel.pc_domain, p->pc_sel.pc_bus, p->pc_sel.pc_dev, 4430 p->pc_sel.pc_func, (p->pc_class << 16) | 4431 (p->pc_subclass << 8) | p->pc_progif, 4432 (p->pc_subdevice << 16) | p->pc_subvendor, 4433 (p->pc_device << 16) | p->pc_vendor, 4434 p->pc_revid, p->pc_hdr); 4435 } 4436 } 4437 #endif /* DDB */ 4438 4439 static struct resource * 4440 pci_reserve_map(device_t dev, device_t child, int type, int *rid, 4441 u_long start, u_long end, u_long count, u_int flags) 4442 { 4443 struct pci_devinfo *dinfo = device_get_ivars(child); 4444 struct resource_list *rl = &dinfo->resources; 4445 struct resource *res; 4446 struct pci_map *pm; 4447 pci_addr_t map, testval; 4448 int mapsize; 4449 4450 res = NULL; 4451 pm = pci_find_bar(child, *rid); 4452 if (pm != NULL) { 4453 /* This is a BAR that we failed to allocate earlier. */ 4454 mapsize = pm->pm_size; 4455 map = pm->pm_value; 4456 } else { 4457 /* 4458 * Weed out the bogons, and figure out how large the 4459 * BAR/map is. BARs that read back 0 here are bogus 4460 * and unimplemented. Note: atapci in legacy mode are 4461 * special and handled elsewhere in the code. If you 4462 * have a atapci device in legacy mode and it fails 4463 * here, that other code is broken. 4464 */ 4465 pci_read_bar(child, *rid, &map, &testval); 4466 4467 /* 4468 * Determine the size of the BAR and ignore BARs with a size 4469 * of 0. Device ROM BARs use a different mask value. 4470 */ 4471 if (PCIR_IS_BIOS(&dinfo->cfg, *rid)) 4472 mapsize = pci_romsize(testval); 4473 else 4474 mapsize = pci_mapsize(testval); 4475 if (mapsize == 0) 4476 goto out; 4477 pm = pci_add_bar(child, *rid, map, mapsize); 4478 } 4479 4480 if (PCI_BAR_MEM(map) || PCIR_IS_BIOS(&dinfo->cfg, *rid)) { 4481 if (type != SYS_RES_MEMORY) { 4482 if (bootverbose) 4483 device_printf(dev, 4484 "child %s requested type %d for rid %#x," 4485 " but the BAR says it is an memio\n", 4486 device_get_nameunit(child), type, *rid); 4487 goto out; 4488 } 4489 } else { 4490 if (type != SYS_RES_IOPORT) { 4491 if (bootverbose) 4492 device_printf(dev, 4493 "child %s requested type %d for rid %#x," 4494 " but the BAR says it is an ioport\n", 4495 device_get_nameunit(child), type, *rid); 4496 goto out; 4497 } 4498 } 4499 4500 /* 4501 * For real BARs, we need to override the size that 4502 * the driver requests, because that's what the BAR 4503 * actually uses and we would otherwise have a 4504 * situation where we might allocate the excess to 4505 * another driver, which won't work. 4506 */ 4507 count = (pci_addr_t)1 << mapsize; 4508 if (RF_ALIGNMENT(flags) < mapsize) 4509 flags = (flags & ~RF_ALIGNMENT_MASK) | RF_ALIGNMENT_LOG2(mapsize); 4510 if (PCI_BAR_MEM(map) && (map & PCIM_BAR_MEM_PREFETCH)) 4511 flags |= RF_PREFETCHABLE; 4512 4513 /* 4514 * Allocate enough resource, and then write back the 4515 * appropriate BAR for that resource. 4516 */ 4517 resource_list_add(rl, type, *rid, start, end, count); 4518 res = resource_list_reserve(rl, dev, child, type, rid, start, end, 4519 count, flags & ~RF_ACTIVE); 4520 if (res == NULL) { 4521 resource_list_delete(rl, type, *rid); 4522 device_printf(child, 4523 "%#lx bytes of rid %#x res %d failed (%#lx, %#lx).\n", 4524 count, *rid, type, start, end); 4525 goto out; 4526 } 4527 if (bootverbose) 4528 device_printf(child, 4529 "Lazy allocation of %#lx bytes rid %#x type %d at %#lx\n", 4530 count, *rid, type, rman_get_start(res)); 4531 map = rman_get_start(res); 4532 pci_write_bar(child, pm, map); 4533 out: 4534 return (res); 4535 } 4536 4537 struct resource * 4538 pci_alloc_resource(device_t dev, device_t child, int type, int *rid, 4539 u_long start, u_long end, u_long count, u_int flags) 4540 { 4541 struct pci_devinfo *dinfo; 4542 struct resource_list *rl; 4543 struct resource_list_entry *rle; 4544 struct resource *res; 4545 pcicfgregs *cfg; 4546 4547 if (device_get_parent(child) != dev) 4548 return (BUS_ALLOC_RESOURCE(device_get_parent(dev), child, 4549 type, rid, start, end, count, flags)); 4550 4551 /* 4552 * Perform lazy resource allocation 4553 */ 4554 dinfo = device_get_ivars(child); 4555 rl = &dinfo->resources; 4556 cfg = &dinfo->cfg; 4557 switch (type) { 4558 #if defined(NEW_PCIB) && defined(PCI_RES_BUS) 4559 case PCI_RES_BUS: 4560 return (pci_alloc_secbus(dev, child, rid, start, end, count, 4561 flags)); 4562 #endif 4563 case SYS_RES_IRQ: 4564 /* 4565 * Can't alloc legacy interrupt once MSI messages have 4566 * been allocated. 4567 */ 4568 if (*rid == 0 && (cfg->msi.msi_alloc > 0 || 4569 cfg->msix.msix_alloc > 0)) 4570 return (NULL); 4571 4572 /* 4573 * If the child device doesn't have an interrupt 4574 * routed and is deserving of an interrupt, try to 4575 * assign it one. 4576 */ 4577 if (*rid == 0 && !PCI_INTERRUPT_VALID(cfg->intline) && 4578 (cfg->intpin != 0)) 4579 pci_assign_interrupt(dev, child, 0); 4580 break; 4581 case SYS_RES_IOPORT: 4582 case SYS_RES_MEMORY: 4583 #ifdef NEW_PCIB 4584 /* 4585 * PCI-PCI bridge I/O window resources are not BARs. 4586 * For those allocations just pass the request up the 4587 * tree. 4588 */ 4589 if (cfg->hdrtype == PCIM_HDRTYPE_BRIDGE) { 4590 switch (*rid) { 4591 case PCIR_IOBASEL_1: 4592 case PCIR_MEMBASE_1: 4593 case PCIR_PMBASEL_1: 4594 /* 4595 * XXX: Should we bother creating a resource 4596 * list entry? 4597 */ 4598 return (bus_generic_alloc_resource(dev, child, 4599 type, rid, start, end, count, flags)); 4600 } 4601 } 4602 #endif 4603 /* Reserve resources for this BAR if needed. */ 4604 rle = resource_list_find(rl, type, *rid); 4605 if (rle == NULL) { 4606 res = pci_reserve_map(dev, child, type, rid, start, end, 4607 count, flags); 4608 if (res == NULL) 4609 return (NULL); 4610 } 4611 } 4612 return (resource_list_alloc(rl, dev, child, type, rid, 4613 start, end, count, flags)); 4614 } 4615 4616 int 4617 pci_release_resource(device_t dev, device_t child, int type, int rid, 4618 struct resource *r) 4619 { 4620 struct pci_devinfo *dinfo; 4621 struct resource_list *rl; 4622 pcicfgregs *cfg; 4623 4624 if (device_get_parent(child) != dev) 4625 return (BUS_RELEASE_RESOURCE(device_get_parent(dev), child, 4626 type, rid, r)); 4627 4628 dinfo = device_get_ivars(child); 4629 cfg = &dinfo->cfg; 4630 #ifdef NEW_PCIB 4631 /* 4632 * PCI-PCI bridge I/O window resources are not BARs. For 4633 * those allocations just pass the request up the tree. 4634 */ 4635 if (cfg->hdrtype == PCIM_HDRTYPE_BRIDGE && 4636 (type == SYS_RES_IOPORT || type == SYS_RES_MEMORY)) { 4637 switch (rid) { 4638 case PCIR_IOBASEL_1: 4639 case PCIR_MEMBASE_1: 4640 case PCIR_PMBASEL_1: 4641 return (bus_generic_release_resource(dev, child, type, 4642 rid, r)); 4643 } 4644 } 4645 #endif 4646 4647 rl = &dinfo->resources; 4648 return (resource_list_release(rl, dev, child, type, rid, r)); 4649 } 4650 4651 int 4652 pci_activate_resource(device_t dev, device_t child, int type, int rid, 4653 struct resource *r) 4654 { 4655 struct pci_devinfo *dinfo; 4656 int error; 4657 4658 error = bus_generic_activate_resource(dev, child, type, rid, r); 4659 if (error) 4660 return (error); 4661 4662 /* Enable decoding in the command register when activating BARs. */ 4663 if (device_get_parent(child) == dev) { 4664 /* Device ROMs need their decoding explicitly enabled. */ 4665 dinfo = device_get_ivars(child); 4666 if (type == SYS_RES_MEMORY && PCIR_IS_BIOS(&dinfo->cfg, rid)) 4667 pci_write_bar(child, pci_find_bar(child, rid), 4668 rman_get_start(r) | PCIM_BIOS_ENABLE); 4669 switch (type) { 4670 case SYS_RES_IOPORT: 4671 case SYS_RES_MEMORY: 4672 error = PCI_ENABLE_IO(dev, child, type); 4673 break; 4674 } 4675 } 4676 return (error); 4677 } 4678 4679 int 4680 pci_deactivate_resource(device_t dev, device_t child, int type, 4681 int rid, struct resource *r) 4682 { 4683 struct pci_devinfo *dinfo; 4684 int error; 4685 4686 error = bus_generic_deactivate_resource(dev, child, type, rid, r); 4687 if (error) 4688 return (error); 4689 4690 /* Disable decoding for device ROMs. */ 4691 if (device_get_parent(child) == dev) { 4692 dinfo = device_get_ivars(child); 4693 if (type == SYS_RES_MEMORY && PCIR_IS_BIOS(&dinfo->cfg, rid)) 4694 pci_write_bar(child, pci_find_bar(child, rid), 4695 rman_get_start(r)); 4696 } 4697 return (0); 4698 } 4699 4700 void 4701 pci_delete_child(device_t dev, device_t child) 4702 { 4703 struct resource_list_entry *rle; 4704 struct resource_list *rl; 4705 struct pci_devinfo *dinfo; 4706 4707 dinfo = device_get_ivars(child); 4708 rl = &dinfo->resources; 4709 4710 if (device_is_attached(child)) 4711 device_detach(child); 4712 4713 /* Turn off access to resources we're about to free */ 4714 pci_write_config(child, PCIR_COMMAND, pci_read_config(child, 4715 PCIR_COMMAND, 2) & ~(PCIM_CMD_MEMEN | PCIM_CMD_PORTEN), 2); 4716 4717 /* Free all allocated resources */ 4718 STAILQ_FOREACH(rle, rl, link) { 4719 if (rle->res) { 4720 if (rman_get_flags(rle->res) & RF_ACTIVE || 4721 resource_list_busy(rl, rle->type, rle->rid)) { 4722 pci_printf(&dinfo->cfg, 4723 "Resource still owned, oops. " 4724 "(type=%d, rid=%d, addr=%lx)\n", 4725 rle->type, rle->rid, 4726 rman_get_start(rle->res)); 4727 bus_release_resource(child, rle->type, rle->rid, 4728 rle->res); 4729 } 4730 resource_list_unreserve(rl, dev, child, rle->type, 4731 rle->rid); 4732 } 4733 } 4734 resource_list_free(rl); 4735 4736 device_delete_child(dev, child); 4737 pci_freecfg(dinfo); 4738 } 4739 4740 void 4741 pci_delete_resource(device_t dev, device_t child, int type, int rid) 4742 { 4743 struct pci_devinfo *dinfo; 4744 struct resource_list *rl; 4745 struct resource_list_entry *rle; 4746 4747 if (device_get_parent(child) != dev) 4748 return; 4749 4750 dinfo = device_get_ivars(child); 4751 rl = &dinfo->resources; 4752 rle = resource_list_find(rl, type, rid); 4753 if (rle == NULL) 4754 return; 4755 4756 if (rle->res) { 4757 if (rman_get_flags(rle->res) & RF_ACTIVE || 4758 resource_list_busy(rl, type, rid)) { 4759 device_printf(dev, "delete_resource: " 4760 "Resource still owned by child, oops. " 4761 "(type=%d, rid=%d, addr=%lx)\n", 4762 type, rid, rman_get_start(rle->res)); 4763 return; 4764 } 4765 resource_list_unreserve(rl, dev, child, type, rid); 4766 } 4767 resource_list_delete(rl, type, rid); 4768 } 4769 4770 struct resource_list * 4771 pci_get_resource_list (device_t dev, device_t child) 4772 { 4773 struct pci_devinfo *dinfo = device_get_ivars(child); 4774 4775 return (&dinfo->resources); 4776 } 4777 4778 bus_dma_tag_t 4779 pci_get_dma_tag(device_t bus, device_t dev) 4780 { 4781 struct pci_softc *sc = device_get_softc(bus); 4782 4783 return (sc->sc_dma_tag); 4784 } 4785 4786 uint32_t 4787 pci_read_config_method(device_t dev, device_t child, int reg, int width) 4788 { 4789 struct pci_devinfo *dinfo = device_get_ivars(child); 4790 pcicfgregs *cfg = &dinfo->cfg; 4791 4792 return (PCIB_READ_CONFIG(device_get_parent(dev), 4793 cfg->bus, cfg->slot, cfg->func, reg, width)); 4794 } 4795 4796 void 4797 pci_write_config_method(device_t dev, device_t child, int reg, 4798 uint32_t val, int width) 4799 { 4800 struct pci_devinfo *dinfo = device_get_ivars(child); 4801 pcicfgregs *cfg = &dinfo->cfg; 4802 4803 PCIB_WRITE_CONFIG(device_get_parent(dev), 4804 cfg->bus, cfg->slot, cfg->func, reg, val, width); 4805 } 4806 4807 int 4808 pci_child_location_str_method(device_t dev, device_t child, char *buf, 4809 size_t buflen) 4810 { 4811 4812 snprintf(buf, buflen, "slot=%d function=%d", pci_get_slot(child), 4813 pci_get_function(child)); 4814 return (0); 4815 } 4816 4817 int 4818 pci_child_pnpinfo_str_method(device_t dev, device_t child, char *buf, 4819 size_t buflen) 4820 { 4821 struct pci_devinfo *dinfo; 4822 pcicfgregs *cfg; 4823 4824 dinfo = device_get_ivars(child); 4825 cfg = &dinfo->cfg; 4826 snprintf(buf, buflen, "vendor=0x%04x device=0x%04x subvendor=0x%04x " 4827 "subdevice=0x%04x class=0x%02x%02x%02x", cfg->vendor, cfg->device, 4828 cfg->subvendor, cfg->subdevice, cfg->baseclass, cfg->subclass, 4829 cfg->progif); 4830 return (0); 4831 } 4832 4833 int 4834 pci_assign_interrupt_method(device_t dev, device_t child) 4835 { 4836 struct pci_devinfo *dinfo = device_get_ivars(child); 4837 pcicfgregs *cfg = &dinfo->cfg; 4838 4839 return (PCIB_ROUTE_INTERRUPT(device_get_parent(dev), child, 4840 cfg->intpin)); 4841 } 4842 4843 static int 4844 pci_modevent(module_t mod, int what, void *arg) 4845 { 4846 static struct cdev *pci_cdev; 4847 4848 switch (what) { 4849 case MOD_LOAD: 4850 STAILQ_INIT(&pci_devq); 4851 pci_generation = 0; 4852 pci_cdev = make_dev(&pcicdev, 0, UID_ROOT, GID_WHEEL, 0644, 4853 "pci"); 4854 pci_load_vendor_data(); 4855 break; 4856 4857 case MOD_UNLOAD: 4858 destroy_dev(pci_cdev); 4859 break; 4860 } 4861 4862 return (0); 4863 } 4864 4865 static void 4866 pci_cfg_restore_pcie(device_t dev, struct pci_devinfo *dinfo) 4867 { 4868 #define WREG(n, v) pci_write_config(dev, pos + (n), (v), 2) 4869 struct pcicfg_pcie *cfg; 4870 int version, pos; 4871 4872 cfg = &dinfo->cfg.pcie; 4873 pos = cfg->pcie_location; 4874 4875 version = cfg->pcie_flags & PCIEM_FLAGS_VERSION; 4876 4877 WREG(PCIER_DEVICE_CTL, cfg->pcie_device_ctl); 4878 4879 if (version > 1 || cfg->pcie_type == PCIEM_TYPE_ROOT_PORT || 4880 cfg->pcie_type == PCIEM_TYPE_ENDPOINT || 4881 cfg->pcie_type == PCIEM_TYPE_LEGACY_ENDPOINT) 4882 WREG(PCIER_LINK_CTL, cfg->pcie_link_ctl); 4883 4884 if (version > 1 || (cfg->pcie_type == PCIEM_TYPE_ROOT_PORT || 4885 (cfg->pcie_type == PCIEM_TYPE_DOWNSTREAM_PORT && 4886 (cfg->pcie_flags & PCIEM_FLAGS_SLOT)))) 4887 WREG(PCIER_SLOT_CTL, cfg->pcie_slot_ctl); 4888 4889 if (version > 1 || cfg->pcie_type == PCIEM_TYPE_ROOT_PORT || 4890 cfg->pcie_type == PCIEM_TYPE_ROOT_EC) 4891 WREG(PCIER_ROOT_CTL, cfg->pcie_root_ctl); 4892 4893 if (version > 1) { 4894 WREG(PCIER_DEVICE_CTL2, cfg->pcie_device_ctl2); 4895 WREG(PCIER_LINK_CTL2, cfg->pcie_link_ctl2); 4896 WREG(PCIER_SLOT_CTL2, cfg->pcie_slot_ctl2); 4897 } 4898 #undef WREG 4899 } 4900 4901 static void 4902 pci_cfg_restore_pcix(device_t dev, struct pci_devinfo *dinfo) 4903 { 4904 pci_write_config(dev, dinfo->cfg.pcix.pcix_location + PCIXR_COMMAND, 4905 dinfo->cfg.pcix.pcix_command, 2); 4906 } 4907 4908 void 4909 pci_cfg_restore(device_t dev, struct pci_devinfo *dinfo) 4910 { 4911 4912 /* 4913 * Only do header type 0 devices. Type 1 devices are bridges, 4914 * which we know need special treatment. Type 2 devices are 4915 * cardbus bridges which also require special treatment. 4916 * Other types are unknown, and we err on the side of safety 4917 * by ignoring them. 4918 */ 4919 if ((dinfo->cfg.hdrtype & PCIM_HDRTYPE) != PCIM_HDRTYPE_NORMAL) 4920 return; 4921 4922 /* 4923 * Restore the device to full power mode. We must do this 4924 * before we restore the registers because moving from D3 to 4925 * D0 will cause the chip's BARs and some other registers to 4926 * be reset to some unknown power on reset values. Cut down 4927 * the noise on boot by doing nothing if we are already in 4928 * state D0. 4929 */ 4930 if (pci_get_powerstate(dev) != PCI_POWERSTATE_D0) 4931 pci_set_powerstate(dev, PCI_POWERSTATE_D0); 4932 pci_restore_bars(dev); 4933 pci_write_config(dev, PCIR_COMMAND, dinfo->cfg.cmdreg, 2); 4934 pci_write_config(dev, PCIR_INTLINE, dinfo->cfg.intline, 1); 4935 pci_write_config(dev, PCIR_INTPIN, dinfo->cfg.intpin, 1); 4936 pci_write_config(dev, PCIR_MINGNT, dinfo->cfg.mingnt, 1); 4937 pci_write_config(dev, PCIR_MAXLAT, dinfo->cfg.maxlat, 1); 4938 pci_write_config(dev, PCIR_CACHELNSZ, dinfo->cfg.cachelnsz, 1); 4939 pci_write_config(dev, PCIR_LATTIMER, dinfo->cfg.lattimer, 1); 4940 pci_write_config(dev, PCIR_PROGIF, dinfo->cfg.progif, 1); 4941 pci_write_config(dev, PCIR_REVID, dinfo->cfg.revid, 1); 4942 4943 /* 4944 * Restore extended capabilities for PCI-Express and PCI-X 4945 */ 4946 if (dinfo->cfg.pcie.pcie_location != 0) 4947 pci_cfg_restore_pcie(dev, dinfo); 4948 if (dinfo->cfg.pcix.pcix_location != 0) 4949 pci_cfg_restore_pcix(dev, dinfo); 4950 4951 /* Restore MSI and MSI-X configurations if they are present. */ 4952 if (dinfo->cfg.msi.msi_location != 0) 4953 pci_resume_msi(dev); 4954 if (dinfo->cfg.msix.msix_location != 0) 4955 pci_resume_msix(dev); 4956 } 4957 4958 static void 4959 pci_cfg_save_pcie(device_t dev, struct pci_devinfo *dinfo) 4960 { 4961 #define RREG(n) pci_read_config(dev, pos + (n), 2) 4962 struct pcicfg_pcie *cfg; 4963 int version, pos; 4964 4965 cfg = &dinfo->cfg.pcie; 4966 pos = cfg->pcie_location; 4967 4968 cfg->pcie_flags = RREG(PCIER_FLAGS); 4969 4970 version = cfg->pcie_flags & PCIEM_FLAGS_VERSION; 4971 4972 cfg->pcie_device_ctl = RREG(PCIER_DEVICE_CTL); 4973 4974 if (version > 1 || cfg->pcie_type == PCIEM_TYPE_ROOT_PORT || 4975 cfg->pcie_type == PCIEM_TYPE_ENDPOINT || 4976 cfg->pcie_type == PCIEM_TYPE_LEGACY_ENDPOINT) 4977 cfg->pcie_link_ctl = RREG(PCIER_LINK_CTL); 4978 4979 if (version > 1 || (cfg->pcie_type == PCIEM_TYPE_ROOT_PORT || 4980 (cfg->pcie_type == PCIEM_TYPE_DOWNSTREAM_PORT && 4981 (cfg->pcie_flags & PCIEM_FLAGS_SLOT)))) 4982 cfg->pcie_slot_ctl = RREG(PCIER_SLOT_CTL); 4983 4984 if (version > 1 || cfg->pcie_type == PCIEM_TYPE_ROOT_PORT || 4985 cfg->pcie_type == PCIEM_TYPE_ROOT_EC) 4986 cfg->pcie_root_ctl = RREG(PCIER_ROOT_CTL); 4987 4988 if (version > 1) { 4989 cfg->pcie_device_ctl2 = RREG(PCIER_DEVICE_CTL2); 4990 cfg->pcie_link_ctl2 = RREG(PCIER_LINK_CTL2); 4991 cfg->pcie_slot_ctl2 = RREG(PCIER_SLOT_CTL2); 4992 } 4993 #undef RREG 4994 } 4995 4996 static void 4997 pci_cfg_save_pcix(device_t dev, struct pci_devinfo *dinfo) 4998 { 4999 dinfo->cfg.pcix.pcix_command = pci_read_config(dev, 5000 dinfo->cfg.pcix.pcix_location + PCIXR_COMMAND, 2); 5001 } 5002 5003 void 5004 pci_cfg_save(device_t dev, struct pci_devinfo *dinfo, int setstate) 5005 { 5006 uint32_t cls; 5007 int ps; 5008 5009 /* 5010 * Only do header type 0 devices. Type 1 devices are bridges, which 5011 * we know need special treatment. Type 2 devices are cardbus bridges 5012 * which also require special treatment. Other types are unknown, and 5013 * we err on the side of safety by ignoring them. Powering down 5014 * bridges should not be undertaken lightly. 5015 */ 5016 if ((dinfo->cfg.hdrtype & PCIM_HDRTYPE) != PCIM_HDRTYPE_NORMAL) 5017 return; 5018 5019 /* 5020 * Some drivers apparently write to these registers w/o updating our 5021 * cached copy. No harm happens if we update the copy, so do so here 5022 * so we can restore them. The COMMAND register is modified by the 5023 * bus w/o updating the cache. This should represent the normally 5024 * writable portion of the 'defined' part of type 0 headers. In 5025 * theory we also need to save/restore the PCI capability structures 5026 * we know about, but apart from power we don't know any that are 5027 * writable. 5028 */ 5029 dinfo->cfg.subvendor = pci_read_config(dev, PCIR_SUBVEND_0, 2); 5030 dinfo->cfg.subdevice = pci_read_config(dev, PCIR_SUBDEV_0, 2); 5031 dinfo->cfg.vendor = pci_read_config(dev, PCIR_VENDOR, 2); 5032 dinfo->cfg.device = pci_read_config(dev, PCIR_DEVICE, 2); 5033 dinfo->cfg.cmdreg = pci_read_config(dev, PCIR_COMMAND, 2); 5034 dinfo->cfg.intline = pci_read_config(dev, PCIR_INTLINE, 1); 5035 dinfo->cfg.intpin = pci_read_config(dev, PCIR_INTPIN, 1); 5036 dinfo->cfg.mingnt = pci_read_config(dev, PCIR_MINGNT, 1); 5037 dinfo->cfg.maxlat = pci_read_config(dev, PCIR_MAXLAT, 1); 5038 dinfo->cfg.cachelnsz = pci_read_config(dev, PCIR_CACHELNSZ, 1); 5039 dinfo->cfg.lattimer = pci_read_config(dev, PCIR_LATTIMER, 1); 5040 dinfo->cfg.baseclass = pci_read_config(dev, PCIR_CLASS, 1); 5041 dinfo->cfg.subclass = pci_read_config(dev, PCIR_SUBCLASS, 1); 5042 dinfo->cfg.progif = pci_read_config(dev, PCIR_PROGIF, 1); 5043 dinfo->cfg.revid = pci_read_config(dev, PCIR_REVID, 1); 5044 5045 if (dinfo->cfg.pcie.pcie_location != 0) 5046 pci_cfg_save_pcie(dev, dinfo); 5047 5048 if (dinfo->cfg.pcix.pcix_location != 0) 5049 pci_cfg_save_pcix(dev, dinfo); 5050 5051 /* 5052 * don't set the state for display devices, base peripherals and 5053 * memory devices since bad things happen when they are powered down. 5054 * We should (a) have drivers that can easily detach and (b) use 5055 * generic drivers for these devices so that some device actually 5056 * attaches. We need to make sure that when we implement (a) we don't 5057 * power the device down on a reattach. 5058 */ 5059 cls = pci_get_class(dev); 5060 if (!setstate) 5061 return; 5062 switch (pci_do_power_nodriver) 5063 { 5064 case 0: /* NO powerdown at all */ 5065 return; 5066 case 1: /* Conservative about what to power down */ 5067 if (cls == PCIC_STORAGE) 5068 return; 5069 /*FALLTHROUGH*/ 5070 case 2: /* Agressive about what to power down */ 5071 if (cls == PCIC_DISPLAY || cls == PCIC_MEMORY || 5072 cls == PCIC_BASEPERIPH) 5073 return; 5074 /*FALLTHROUGH*/ 5075 case 3: /* Power down everything */ 5076 break; 5077 } 5078 /* 5079 * PCI spec says we can only go into D3 state from D0 state. 5080 * Transition from D[12] into D0 before going to D3 state. 5081 */ 5082 ps = pci_get_powerstate(dev); 5083 if (ps != PCI_POWERSTATE_D0 && ps != PCI_POWERSTATE_D3) 5084 pci_set_powerstate(dev, PCI_POWERSTATE_D0); 5085 if (pci_get_powerstate(dev) != PCI_POWERSTATE_D3) 5086 pci_set_powerstate(dev, PCI_POWERSTATE_D3); 5087 } 5088 5089 /* Wrapper APIs suitable for device driver use. */ 5090 void 5091 pci_save_state(device_t dev) 5092 { 5093 struct pci_devinfo *dinfo; 5094 5095 dinfo = device_get_ivars(dev); 5096 pci_cfg_save(dev, dinfo, 0); 5097 } 5098 5099 void 5100 pci_restore_state(device_t dev) 5101 { 5102 struct pci_devinfo *dinfo; 5103 5104 dinfo = device_get_ivars(dev); 5105 pci_cfg_restore(dev, dinfo); 5106 } 5107 5108 static uint16_t 5109 pci_get_rid_method(device_t dev, device_t child) 5110 { 5111 5112 return (PCIB_GET_RID(device_get_parent(dev), child)); 5113 } 5114