1 /* $FreeBSD$ */ 2 /*- 3 * Copyright (c) 2000-2010, LSI Logic Corporation and its contributors. 4 * All rights reserved. 5 * 6 * Redistribution and use in source and binary forms, with or without 7 * modification, are permitted provided that the following conditions are 8 * met: 9 * 1. Redistributions of source code must retain the above copyright 10 * notice, this list of conditions and the following disclaimer. 11 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 12 * substantially similar to the "NO WARRANTY" disclaimer below 13 * ("Disclaimer") and any redistribution must be conditioned upon including 14 * a substantially similar Disclaimer requirement for further binary 15 * redistribution. 16 * 3. Neither the name of the LSI Logic Corporation nor the names of its 17 * contributors may be used to endorse or promote products derived from 18 * this software without specific prior written permission. 19 * 20 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 21 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE 24 * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF THE COPYRIGHT 30 * OWNER OR CONTRIBUTOR IS ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 31 */ 32 33 /*************************************************************************** 34 * * 35 * Description * 36 * ------------ * 37 * This include file contains SAS firmware interface IOC Log Info codes * 38 * * 39 *-------------------------------------------------------------------------* 40 */ 41 42 #ifndef IOPI_IOCLOGINFO_H_INCLUDED 43 #define IOPI_IOCLOGINFO_H_INCLUDED 44 45 #define SAS_LOGINFO_NEXUS_LOSS 0x31170000 46 #define SAS_LOGINFO_MASK 0xFFFF0000 47 48 /****************************************************************************/ 49 /* IOC LOGINFO defines, 0x00000000 - 0x0FFFFFFF */ 50 /* Format: */ 51 /* Bits 31-28: MPI_IOCLOGINFO_TYPE_SAS (3) */ 52 /* Bits 27-24: IOC_LOGINFO_ORIGINATOR: 0=IOP, 1=PL, 2=IR */ 53 /* Bits 23-16: LOGINFO_CODE */ 54 /* Bits 15-0: LOGINFO_CODE Specific */ 55 /****************************************************************************/ 56 57 /****************************************************************************/ 58 /* IOC_LOGINFO_ORIGINATOR defines */ 59 /****************************************************************************/ 60 #define IOC_LOGINFO_ORIGINATOR_IOP (0x00000000) 61 #define IOC_LOGINFO_ORIGINATOR_PL (0x01000000) 62 #define IOC_LOGINFO_ORIGINATOR_IR (0x02000000) 63 64 #define IOC_LOGINFO_ORIGINATOR_MASK (0x0F000000) 65 66 /****************************************************************************/ 67 /* LOGINFO_CODE defines */ 68 /****************************************************************************/ 69 #define IOC_LOGINFO_CODE_MASK (0x00FF0000) 70 #define IOC_LOGINFO_CODE_SHIFT (16) 71 72 /****************************************************************************/ 73 /* IOP LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IOP */ 74 /****************************************************************************/ 75 #define IOP_LOGINFO_CODE_INVALID_SAS_ADDRESS (0x00010000) 76 #define IOP_LOGINFO_CODE_UNUSED2 (0x00020000) 77 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x00030000) 78 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_RT (0x00030100) /* Route Table Entry not found */ 79 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PN (0x00030200) /* Invalid Page Number */ 80 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM (0x00030300) /* Invalid FORM */ 81 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x00030400) /* Invalid Page Type */ 82 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DNM (0x00030500) /* Device Not Mapped */ 83 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_PERSIST (0x00030600) /* Persistent Page not found */ 84 #define IOP_LOGINFO_CODE_CONFIG_INVALID_PAGE_DEFAULT (0x00030700) /* Default Page not found */ 85 86 #define IOP_LOGINFO_CODE_FWUPLOAD_NO_FLASH_AVAILABLE (0x0003E000) /* Tried to upload from flash, but there is none */ 87 #define IOP_LOGINFO_CODE_FWUPLOAD_UNKNOWN_IMAGE_TYPE (0x0003E001) /* ImageType field contents were invalid */ 88 #define IOP_LOGINFO_CODE_FWUPLOAD_WRONG_IMAGE_SIZE (0x0003E002) /* ImageSize field in TCSGE was bad/offset in MfgPg 4 was wrong */ 89 #define IOP_LOGINFO_CODE_FWUPLOAD_ENTIRE_FLASH_UPLOAD_FAILED (0x0003E003) /* Error occured while attempting to upload the entire flash */ 90 #define IOP_LOGINFO_CODE_FWUPLOAD_REGION_UPLOAD_FAILED (0x0003E004) /* Error occured while attempting to upload single flash region */ 91 #define IOP_LOGINFO_CODE_FWUPLOAD_DMA_FAILURE (0x0003E005) /* Problem occured while DMAing FW to host memory */ 92 93 #define IOP_LOGINFO_CODE_DIAG_MSG_ERROR (0x00040000) /* Error handling diag msg - or'd with diag status */ 94 95 #define IOP_LOGINFO_CODE_TASK_TERMINATED (0x00050000) 96 97 #define IOP_LOGINFO_CODE_ENCL_MGMT_READ_ACTION_ERR0R (0x00060001) /* Read Action not supported for SEP msg */ 98 #define IOP_LOGINFO_CODE_ENCL_MGMT_INVALID_BUS_ID_ERR0R (0x00060002) /* Invalid Bus/ID in SEP msg */ 99 100 #define IOP_LOGINFO_CODE_TARGET_ASSIST_TERMINATED (0x00070001) 101 #define IOP_LOGINFO_CODE_TARGET_STATUS_SEND_TERMINATED (0x00070002) 102 #define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_ALL_IO (0x00070003) 103 #define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO (0x00070004) 104 #define IOP_LOGINFO_CODE_TARGET_MODE_ABORT_EXACT_IO_REQ (0x00070005) 105 106 #define IOP_LOGINFO_CODE_LOG_TIMESTAMP_EVENT (0x00080000) 107 108 /****************************************************************************/ 109 /* PL LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = PL */ 110 /****************************************************************************/ 111 #define PL_LOGINFO_CODE_OPEN_FAILURE (0x00010000) /* see SUB_CODE_OPEN_FAIL_ below */ 112 113 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_NO_DEST_TIME_OUT (0x00000001) 114 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PATHWAY_BLOCKED (0x00000002) 115 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_CONTINUE0 (0x00000003) 116 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_CONTINUE1 (0x00000004) 117 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_INITIALIZE0 (0x00000005) 118 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_INITIALIZE1 (0x00000006) 119 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_STOP0 (0x00000007) 120 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RES_STOP1 (0x00000008) 121 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RETRY (0x00000009) 122 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_BREAK (0x0000000A) 123 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_UNUSED_0B (0x0000000B) 124 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_OPEN_TIMEOUT_EXP (0x0000000C) 125 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_UNUSED_0D (0x0000000D) 126 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_DVTBLE_ACCSS_FAIL (0x0000000E) 127 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_BAD_DEST (0x00000011) 128 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RATE_NOT_SUPP (0x00000012) 129 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PROT_NOT_SUPP (0x00000013) 130 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON0 (0x00000014) 131 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON1 (0x00000015) 132 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON2 (0x00000016) 133 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_RESERVED_ABANDON3 (0x00000017) 134 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_STP_RESOURCES_BSY (0x00000018) 135 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_WRONG_DESTINATION (0x00000019) 136 137 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_PATH_BLOCKED (0x0000001B) /* Retry Timeout */ 138 #define PL_LOGINFO_SUB_CODE_OPEN_FAIL_AWT_MAXED (0x0000001C) /* Retry Timeout */ 139 140 141 142 #define PL_LOGINFO_CODE_INVALID_SGL (0x00020000) 143 #define PL_LOGINFO_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00030000) 144 #define PL_LOGINFO_CODE_FRAME_XFER_ERROR (0x00040000) 145 #define PL_LOGINFO_CODE_TX_FM_CONNECTED_LOW (0x00050000) 146 #define PL_LOGINFO_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00060000) 147 #define PL_LOGINFO_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR (0x00070000) 148 #define PL_LOGINFO_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR (0x00080000) 149 #define PL_LOGINFO_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS (0x00090000) 150 #define PL_LOGINFO_CODE_RX_FM_INVALID_MESSAGE (0x000A0000) 151 #define PL_LOGINFO_CODE_RX_CTX_MESSAGE_VALID_ERROR (0x000B0000) 152 #define PL_LOGINFO_CODE_RX_FM_CURRENT_FRAME_ERROR (0x000C0000) 153 #define PL_LOGINFO_CODE_SATA_LINK_DOWN (0x000D0000) 154 #define PL_LOGINFO_CODE_DISCOVERY_SATA_INIT_W_IOS (0x000E0000) 155 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE (0x000F0000) 156 #define PL_LOGINFO_CODE_CONFIG_PL_NOT_INITIALIZED (0x000F0001) /* PL not yet initialized, can't do config page req. */ 157 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PT (0x000F0100) /* Invalid Page Type */ 158 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NUM_PHYS (0x000F0200) /* Invalid Number of Phys */ 159 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NOT_IMP (0x000F0300) /* Case Not Handled */ 160 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_DEV (0x000F0400) /* No Device Found */ 161 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_FORM (0x000F0500) /* Invalid FORM */ 162 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_PHY (0x000F0600) /* Invalid Phy */ 163 #define PL_LOGINFO_CODE_CONFIG_INVALID_PAGE_NO_OWNER (0x000F0700) /* No Owner Found */ 164 #define PL_LOGINFO_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00100000) 165 #define PL_LOGINFO_CODE_RESET (0x00110000) /* See Sub-Codes below (PL_LOGINFO_SUB_CODE) */ 166 #define PL_LOGINFO_CODE_ABORT (0x00120000) /* See Sub-Codes below (PL_LOGINFO_SUB_CODE)*/ 167 #define PL_LOGINFO_CODE_IO_NOT_YET_EXECUTED (0x00130000) 168 #define PL_LOGINFO_CODE_IO_EXECUTED (0x00140000) 169 #define PL_LOGINFO_CODE_PERS_RESV_OUT_NOT_AFFIL_OWNER (0x00150000) 170 #define PL_LOGINFO_CODE_OPEN_TXDMA_ABORT (0x00160000) 171 #define PL_LOGINFO_CODE_IO_DEVICE_MISSING_DELAY_RETRY (0x00170000) 172 #define PL_LOGINFO_CODE_IO_CANCELLED_DUE_TO_R_ERR (0x00180000) 173 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE (0x00000100) 174 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_NO_DEST_TIMEOUT (0x00000101) 175 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_SATA_NEG_RATE_2HI (0x00000102) 176 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_RATE_NOT_SUPPORTED (0x00000103) 177 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_BREAK (0x00000104) 178 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ZONE_VIOLATION (0x00000114) 179 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON0 (0x00000114) /* Open Reject (Zone Violation) - available on SAS-2 devices */ 180 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON1 (0x00000115) 181 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON2 (0x00000116) 182 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ABANDON3 (0x00000117) 183 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_ORR_TIMEOUT (0x0000011A) /* Open Reject (Retry) Timeout */ 184 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_PATH_BLOCKED (0x0000011B) 185 #define PL_LOGINFO_SUB_CODE_OPEN_FAILURE_AWT_MAXED (0x0000011C) /* Arbitration Wait Timer Maxed */ 186 187 #define PL_LOGINFO_SUB_CODE_TARGET_BUS_RESET (0x00000120) 188 #define PL_LOGINFO_SUB_CODE_TRANSPORT_LAYER (0x00000130) /* Leave lower nibble (1-f) reserved. */ 189 #define PL_LOGINFO_SUB_CODE_PORT_LAYER (0x00000140) /* Leave lower nibble (1-f) reserved. */ 190 191 192 #define PL_LOGINFO_SUB_CODE_INVALID_SGL (0x00000200) 193 #define PL_LOGINFO_SUB_CODE_WRONG_REL_OFF_OR_FRAME_LENGTH (0x00000300) 194 #define PL_LOGINFO_SUB_CODE_FRAME_XFER_ERROR (0x00000400) /* Bits 0-3 encode Transport Status Register (offset 0x08) */ 195 /* Bit 0 is Status Bit 0: FrameXferErr */ 196 /* Bit 1 & 2 are Status Bits 16 and 17: FrameXmitErrStatus */ 197 /* Bit 3 is Status Bit 18 WriteDataLenghtGTDataLengthErr */ 198 199 #define PL_LOGINFO_SUB_CODE_TX_FM_CONNECTED_LOW (0x00000500) 200 #define PL_LOGINFO_SUB_CODE_SATA_NON_NCQ_RW_ERR_BIT_SET (0x00000600) 201 #define PL_LOGINFO_SUB_CODE_SATA_READ_LOG_RECEIVE_DATA_ERR (0x00000700) 202 #define PL_LOGINFO_SUB_CODE_SATA_NCQ_FAIL_ALL_CMDS_AFTR_ERR (0x00000800) 203 #define PL_LOGINFO_SUB_CODE_SATA_ERR_IN_RCV_SET_DEV_BIT_FIS (0x00000900) 204 #define PL_LOGINFO_SUB_CODE_RX_FM_INVALID_MESSAGE (0x00000A00) 205 #define PL_LOGINFO_SUB_CODE_RX_CTX_MESSAGE_VALID_ERROR (0x00000B00) 206 #define PL_LOGINFO_SUB_CODE_RX_FM_CURRENT_FRAME_ERROR (0x00000C00) 207 #define PL_LOGINFO_SUB_CODE_SATA_LINK_DOWN (0x00000D00) 208 #define PL_LOGINFO_SUB_CODE_DISCOVERY_SATA_INIT_W_IOS (0x00000E00) 209 #define PL_LOGINFO_SUB_CODE_DISCOVERY_REMOTE_SEP_RESET (0x00000E01) 210 #define PL_LOGINFO_SUB_CODE_SECOND_OPEN (0x00000F00) 211 #define PL_LOGINFO_SUB_CODE_DSCVRY_SATA_INIT_TIMEOUT (0x00001000) 212 #define PL_LOGINFO_SUB_CODE_BREAK_ON_SATA_CONNECTION (0x00002000) /* not currently used in mainline */ 213 #define PL_LOGINFO_SUB_CODE_BREAK_ON_STUCK_LINK (0x00003000) 214 #define PL_LOGINFO_SUB_CODE_BREAK_ON_STUCK_LINK_AIP (0x00004000) 215 #define PL_LOGINFO_SUB_CODE_BREAK_ON_INCOMPLETE_BREAK_RCVD (0x00005000) 216 217 #define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_FAILURE (0x00200000) /* Can't get SMP Frame */ 218 #define PL_LOGINFO_CODE_ENCL_MGMT_SMP_READ_ERROR (0x00200010) /* Error occured on SMP Read */ 219 #define PL_LOGINFO_CODE_ENCL_MGMT_SMP_WRITE_ERROR (0x00200020) /* Error occured on SMP Write */ 220 #define PL_LOGINFO_CODE_ENCL_MGMT_NOT_SUPPORTED_ON_ENCL (0x00200040) /* Encl Mgmt services not available for this WWID */ 221 #define PL_LOGINFO_CODE_ENCL_MGMT_ADDR_MODE_NOT_SUPPORTED (0x00200050) /* Address Mode not suppored */ 222 #define PL_LOGINFO_CODE_ENCL_MGMT_BAD_SLOT_NUM (0x00200060) /* Invalid Slot Number in SEP Msg */ 223 #define PL_LOGINFO_CODE_ENCL_MGMT_SGPIO_NOT_PRESENT (0x00200070) /* SGPIO not present/enabled */ 224 #define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_NOT_CONFIGURED (0x00200080) /* GPIO not configured */ 225 #define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_FRAME_ERROR (0x00200090) /* GPIO can't allocate a frame */ 226 #define PL_LOGINFO_CODE_ENCL_MGMT_GPIO_CONFIG_PAGE_ERROR (0x002000A0) /* GPIO failed config page request */ 227 #define PL_LOGINFO_CODE_ENCL_MGMT_SES_FRAME_ALLOC_ERROR (0x002000B0) /* Can't get frame for SES command */ 228 #define PL_LOGINFO_CODE_ENCL_MGMT_SES_IO_ERROR (0x002000C0) /* I/O execution error */ 229 #define PL_LOGINFO_CODE_ENCL_MGMT_SES_RETRIES_EXHAUSTED (0x002000D0) /* SEP I/O retries exhausted */ 230 #define PL_LOGINFO_CODE_ENCL_MGMT_SMP_FRAME_ALLOC_ERROR (0x002000E0) /* Can't get frame for SMP command */ 231 232 #define PL_LOGINFO_DA_SEP_NOT_PRESENT (0x00200100) /* SEP not present when msg received */ 233 #define PL_LOGINFO_DA_SEP_SINGLE_THREAD_ERROR (0x00200101) /* Can only accept 1 msg at a time */ 234 #define PL_LOGINFO_DA_SEP_ISTWI_INTR_IN_IDLE_STATE (0x00200102) /* ISTWI interrupt recvd. while IDLE */ 235 #define PL_LOGINFO_DA_SEP_RECEIVED_NACK_FROM_SLAVE (0x00200103) /* SEP NACK'd, it is busy */ 236 #define PL_LOGINFO_DA_SEP_DID_NOT_RECEIVE_ACK (0x00200104) /* SEP didn't rcv. ACK (Last Rcvd Bit = 1) */ 237 #define PL_LOGINFO_DA_SEP_BAD_STATUS_HDR_CHKSUM (0x00200105) /* SEP stopped or sent bad chksum in Hdr */ 238 #define PL_LOGINFO_DA_SEP_STOP_ON_DATA (0x00200106) /* SEP stopped while transfering data */ 239 #define PL_LOGINFO_DA_SEP_STOP_ON_SENSE_DATA (0x00200107) /* SEP stopped while transfering sense data */ 240 #define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_1 (0x00200108) /* SEP returned unknown scsi status */ 241 #define PL_LOGINFO_DA_SEP_UNSUPPORTED_SCSI_STATUS_2 (0x00200109) /* SEP returned unknown scsi status */ 242 #define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP (0x0020010A) /* SEP returned bad chksum after STOP */ 243 #define PL_LOGINFO_DA_SEP_CHKSUM_ERROR_AFTER_STOP_GETDATA (0x0020010B) /* SEP returned bad chksum after STOP while gettin data*/ 244 #define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND (0x0020010C) /* SEP doesn't support CDB opcode f/w location 1 */ 245 #define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND_2 (0x0020010D) /* SEP doesn't support CDB opcode f/w location 2 */ 246 #define PL_LOGINFO_DA_SEP_UNSUPPORTED_COMMAND_3 (0x0020010E) /* SEP doesn't support CDB opcode f/w location 3 */ 247 248 249 /****************************************************************************/ 250 /* IR LOGINFO_CODE defines, valid if IOC_LOGINFO_ORIGINATOR = IR */ 251 /****************************************************************************/ 252 #define IR_LOGINFO_RAID_ACTION_ERROR (0x00010000) 253 #define IR_LOGINFO_CODE_UNUSED2 (0x00020000) 254 255 /* Amount of information passed down for Create Volume is too large */ 256 #define IR_LOGINFO_VOLUME_CREATE_INVALID_LENGTH (0x00010001) 257 /* Creation of duplicate volume attempted (Bus/Target ID checked) */ 258 #define IR_LOGINFO_VOLUME_CREATE_DUPLICATE (0x00010002) 259 /* Creation failed due to maximum number of supported volumes exceeded */ 260 #define IR_LOGINFO_VOLUME_CREATE_NO_SLOTS (0x00010003) 261 /* Creation failed due to DMA error in trying to read from host */ 262 #define IR_LOGINFO_VOLUME_CREATE_DMA_ERROR (0x00010004) 263 /* Creation failed due to invalid volume type passed down */ 264 #define IR_LOGINFO_VOLUME_CREATE_INVALID_VOLUME_TYPE (0x00010005) 265 /* Creation failed due to error reading MFG Page 4 */ 266 #define IR_LOGINFO_VOLUME_MFG_PAGE4_ERROR (0x00010006) 267 /* Creation failed when trying to create internal structures */ 268 #define IR_LOGINFO_VOLUME_INTERNAL_CONFIG_STRUCTURE_ERROR (0x00010007) 269 270 /* Activation failed due to trying to activate an already active volume */ 271 #define IR_LOGINFO_VOLUME_ACTIVATING_AN_ACTIVE_VOLUME (0x00010010) 272 /* Activation failed due to trying to active unsupported volume type */ 273 #define IR_LOGINFO_VOLUME_ACTIVATING_INVALID_VOLUME_TYPE (0x00010011) 274 /* Activation failed due to trying to active too many volumes */ 275 #define IR_LOGINFO_VOLUME_ACTIVATING_TOO_MANY_VOLUMES (0x00010012) 276 /* Activation failed due to Volume ID in use already */ 277 #define IR_LOGINFO_VOLUME_ACTIVATING_VOLUME_ID_IN_USE (0x00010013) 278 /* Activation failed call to activateVolume returned failure */ 279 #define IR_LOGINFO_VOLUME_ACTIVATE_VOLUME_FAILED (0x00010014) 280 /* Activation failed trying to import the volume */ 281 #define IR_LOGINFO_VOLUME_ACTIVATING_IMPORT_VOLUME_FAILED (0x00010015) 282 /* Activation failed trying to import the volume */ 283 #define IR_LOGINFO_VOLUME_ACTIVATING_TOO_MANY_PHYS_DISKS (0x00010016) 284 285 /* Phys Disk failed, too many phys disks */ 286 #define IR_LOGINFO_PHYSDISK_CREATE_TOO_MANY_DISKS (0x00010020) 287 /* Amount of information passed down for Create Pnysdisk is too large */ 288 #define IR_LOGINFO_PHYSDISK_CREATE_INVALID_LENGTH (0x00010021) 289 /* Creation failed due to DMA error in trying to read from host */ 290 #define IR_LOGINFO_PHYSDISK_CREATE_DMA_ERROR (0x00010022) 291 /* Creation failed due to invalid Bus TargetID passed down */ 292 #define IR_LOGINFO_PHYSDISK_CREATE_BUS_TID_INVALID (0x00010023) 293 /* Creation failed due to error in creating RAID Phys Disk Config Page */ 294 #define IR_LOGINFO_PHYSDISK_CREATE_CONFIG_PAGE_ERROR (0x00010024) 295 296 297 /* Compatibility Error : IR Disabled */ 298 #define IR_LOGINFO_COMPAT_ERROR_RAID_DISABLED (0x00010030) 299 /* Compatibility Error : Inquiry Comand failed */ 300 #define IR_LOGINFO_COMPAT_ERROR_INQUIRY_FAILED (0x00010031) 301 /* Compatibility Error : Device not direct access device */ 302 #define IR_LOGINFO_COMPAT_ERROR_NOT_DIRECT_ACCESS (0x00010032) 303 /* Compatibility Error : Removable device found */ 304 #define IR_LOGINFO_COMPAT_ERROR_REMOVABLE_FOUND (0x00010033) 305 /* Compatibility Error : Device SCSI Version not 2 or higher */ 306 #define IR_LOGINFO_COMPAT_ERROR_NEED_SCSI_2_OR_HIGHER (0x00010034) 307 /* Compatibility Error : SATA device, 48 BIT LBA not supported */ 308 #define IR_LOGINFO_COMPAT_ERROR_SATA_48BIT_LBA_NOT_SUPPORTED (0x00010035) 309 /* Compatibility Error : Device does not have 512 byte block sizes */ 310 #define IR_LOGINFO_COMPAT_ERROR_DEVICE_NOT_512_BYTE_BLOCK (0x00010036) 311 /* Compatibility Error : Volume Type check failed */ 312 #define IR_LOGINFO_COMPAT_ERROR_VOLUME_TYPE_CHECK_FAILED (0x00010037) 313 /* Compatibility Error : Volume Type is unsupported by FW */ 314 #define IR_LOGINFO_COMPAT_ERROR_UNSUPPORTED_VOLUME_TYPE (0x00010038) 315 /* Compatibility Error : Disk drive too small for use in volume */ 316 #define IR_LOGINFO_COMPAT_ERROR_DISK_TOO_SMALL (0x00010039) 317 /* Compatibility Error : Phys disk for Create Volume not found */ 318 #define IR_LOGINFO_COMPAT_ERROR_PHYS_DISK_NOT_FOUND (0x0001003A) 319 /* Compatibility Error : membership count error, too many or too few disks for volume type */ 320 #define IR_LOGINFO_COMPAT_ERROR_MEMBERSHIP_COUNT (0x0001003B) 321 /* Compatibility Error : Disk stripe sizes must be 64KB */ 322 #define IR_LOGINFO_COMPAT_ERROR_NON_64K_STRIPE_SIZE (0x0001003C) 323 /* Compatibility Error : IME size limited to < 2TB */ 324 #define IR_LOGINFO_COMPAT_ERROR_IME_VOL_NOT_CURRENTLY_SUPPORTED (0x0001003D) 325 326 /* Device Firmware Update: DFU can only be started once */ 327 #define IR_LOGINFO_DEV_FW_UPDATE_ERR_DFU_IN_PROGRESS (0x00010050) 328 /* Device Firmware Update: Volume must be Optimal/Active/non-Quiesced */ 329 #define IR_LOGINFO_DEV_FW_UPDATE_ERR_DEVICE_IN_INVALID_STATE (0x00010051) 330 /* Device Firmware Update: DFU Timeout cannot be zero */ 331 #define IR_LOGINFO_DEV_FW_UPDATE_ERR_INVALID_TIMEOUT (0x00010052) 332 /* Device Firmware Update: CREATE TIMER FAILED */ 333 #define IR_LOGINFO_DEV_FW_UPDATE_ERR_NO_TIMERS (0x00010053) 334 /* Device Firmware Update: Failed to read SAS_IO_UNIT_PG_1 */ 335 #define IR_LOGINFO_DEV_FW_UPDATE_ERR_READING_CFG_PAGE (0x00010054) 336 /* Device Firmware Update: Invalid SAS_IO_UNIT_PG_1 value(s) */ 337 #define IR_LOGINFO_DEV_FW_UPDATE_ERR_PORT_IO_TIMEOUTS_REQUIRED (0x00010055) 338 /* Device Firmware Update: Unable to allocate memory for page */ 339 #define IR_LOGINFO_DEV_FW_UPDATE_ERR_ALLOC_CFG_PAGE (0x00010056) 340 /* Device Firmware Update: */ 341 //#define IR_LOGINFO_DEV_FW_UPDATE_ERR_ (0x00010054) 342 343 344 /****************************************************************************/ 345 /* Defines for convenience */ 346 /****************************************************************************/ 347 #define IOC_LOGINFO_PREFIX_IOP ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IOP) 348 #define IOC_LOGINFO_PREFIX_PL ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_PL) 349 #define IOC_LOGINFO_PREFIX_IR ((MPI_IOCLOGINFO_TYPE_SAS << MPI_IOCLOGINFO_TYPE_SHIFT) | IOC_LOGINFO_ORIGINATOR_IR) 350 351 #endif /* end of file */ 352 353