1 /* $NetBSD: nsphy.c,v 1.18 1999/07/14 23:57:36 thorpej Exp $ */ 2 3 /*- 4 * SPDX-License-Identifier: BSD-2-Clause-NetBSD AND BSD-2-Clause 5 * 6 * Copyright (c) 1998, 1999 The NetBSD Foundation, Inc. 7 * All rights reserved. 8 * 9 * This code is derived from software contributed to The NetBSD Foundation 10 * by Jason R. Thorpe of the Numerical Aerospace Simulation Facility, 11 * NASA Ames Research Center. 12 * 13 * Redistribution and use in source and binary forms, with or without 14 * modification, are permitted provided that the following conditions 15 * are met: 16 * 1. Redistributions of source code must retain the above copyright 17 * notice, this list of conditions and the following disclaimer. 18 * 2. Redistributions in binary form must reproduce the above copyright 19 * notice, this list of conditions and the following disclaimer in the 20 * documentation and/or other materials provided with the distribution. 21 * 22 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS 23 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 24 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 25 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS 26 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 27 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 28 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 29 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 30 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 31 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 32 * POSSIBILITY OF SUCH DAMAGE. 33 */ 34 35 /*- 36 * Copyright (c) 1997 Manuel Bouyer. All rights reserved. 37 * 38 * Redistribution and use in source and binary forms, with or without 39 * modification, are permitted provided that the following conditions 40 * are met: 41 * 1. Redistributions of source code must retain the above copyright 42 * notice, this list of conditions and the following disclaimer. 43 * 2. Redistributions in binary form must reproduce the above copyright 44 * notice, this list of conditions and the following disclaimer in the 45 * documentation and/or other materials provided with the distribution. 46 * 47 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 48 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 49 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 50 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, 51 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 52 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 53 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 54 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 55 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF 56 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 57 */ 58 59 #include <sys/cdefs.h> 60 __FBSDID("$FreeBSD$"); 61 62 /* 63 * driver for National Semiconductor's DP83840A ethernet 10/100 PHY 64 * Data Sheet available from www.national.com 65 */ 66 67 #include <sys/param.h> 68 #include <sys/systm.h> 69 #include <sys/kernel.h> 70 #include <sys/socket.h> 71 #include <sys/errno.h> 72 #include <sys/module.h> 73 #include <sys/bus.h> 74 75 #include <net/if.h> 76 #include <net/if_var.h> 77 #include <net/if_media.h> 78 79 #include <dev/mii/mii.h> 80 #include <dev/mii/miivar.h> 81 #include "miidevs.h" 82 83 #include <dev/mii/nsphyreg.h> 84 85 #include "miibus_if.h" 86 87 static int nsphy_probe(device_t); 88 static int nsphy_attach(device_t); 89 90 static device_method_t nsphy_methods[] = { 91 /* device interface */ 92 DEVMETHOD(device_probe, nsphy_probe), 93 DEVMETHOD(device_attach, nsphy_attach), 94 DEVMETHOD(device_detach, mii_phy_detach), 95 DEVMETHOD(device_shutdown, bus_generic_shutdown), 96 DEVMETHOD_END 97 }; 98 99 static driver_t nsphy_driver = { 100 "nsphy", 101 nsphy_methods, 102 sizeof(struct mii_softc) 103 }; 104 105 DRIVER_MODULE(nsphy, miibus, nsphy_driver, 0, 0); 106 107 static int nsphy_service(struct mii_softc *, struct mii_data *, int); 108 static void nsphy_status(struct mii_softc *); 109 static void nsphy_reset(struct mii_softc *); 110 111 static const struct mii_phydesc nsphys[] = { 112 MII_PHY_DESC(xxNATSEMI, DP83840), 113 MII_PHY_END 114 }; 115 116 static const struct mii_phy_funcs nsphy_funcs = { 117 nsphy_service, 118 nsphy_status, 119 nsphy_reset 120 }; 121 122 static int 123 nsphy_probe(device_t dev) 124 { 125 126 return (mii_phy_dev_probe(dev, nsphys, BUS_PROBE_DEFAULT)); 127 } 128 129 static int 130 nsphy_attach(device_t dev) 131 { 132 133 mii_phy_dev_attach(dev, MIIF_NOMANPAUSE, &nsphy_funcs, 1); 134 return (0); 135 } 136 137 static int 138 nsphy_service(struct mii_softc *sc, struct mii_data *mii, int cmd) 139 { 140 int reg; 141 142 switch (cmd) { 143 case MII_POLLSTAT: 144 break; 145 146 case MII_MEDIACHG: 147 reg = PHY_READ(sc, MII_NSPHY_PCR); 148 149 /* 150 * Set up the PCR to use LED4 to indicate full-duplex 151 * in both 10baseT and 100baseTX modes. 152 */ 153 reg |= PCR_LED4MODE; 154 155 /* 156 * Make sure Carrier Integrity Monitor function is 157 * disabled (normal for Node operation, but sometimes 158 * it's not set?!) 159 */ 160 reg |= PCR_CIMDIS; 161 162 /* 163 * Make sure "force link good" is set to normal mode. 164 * It's only intended for debugging. 165 */ 166 reg |= PCR_FLINK100; 167 168 /* 169 * Mystery bits which are supposedly `reserved', 170 * but we seem to need to set them when the PHY 171 * is connected to some interfaces: 172 * 173 * 0x0400 is needed for fxp 174 * (Intel EtherExpress Pro 10+/100B, 82557 chip) 175 * (nsphy with a DP83840 chip) 176 * 0x0100 may be needed for some other card 177 */ 178 reg |= 0x0100 | 0x0400; 179 180 if (mii_phy_mac_match(sc, "fxp")) 181 PHY_WRITE(sc, MII_NSPHY_PCR, reg); 182 183 mii_phy_setmedia(sc); 184 break; 185 186 case MII_TICK: 187 if (mii_phy_tick(sc) == EJUSTRETURN) 188 return (0); 189 break; 190 } 191 192 /* Update the media status. */ 193 PHY_STATUS(sc); 194 195 /* Callback if something changed. */ 196 mii_phy_update(sc, cmd); 197 return (0); 198 } 199 200 static void 201 nsphy_status(struct mii_softc *sc) 202 { 203 struct mii_data *mii = sc->mii_pdata; 204 struct ifmedia_entry *ife = mii->mii_media.ifm_cur; 205 int bmsr, bmcr, par, anlpar; 206 207 mii->mii_media_status = IFM_AVALID; 208 mii->mii_media_active = IFM_ETHER; 209 210 bmsr = PHY_READ(sc, MII_BMSR) | 211 PHY_READ(sc, MII_BMSR); 212 if (bmsr & BMSR_LINK) 213 mii->mii_media_status |= IFM_ACTIVE; 214 215 bmcr = PHY_READ(sc, MII_BMCR); 216 if (bmcr & BMCR_ISO) { 217 mii->mii_media_active |= IFM_NONE; 218 mii->mii_media_status = 0; 219 return; 220 } 221 222 if (bmcr & BMCR_LOOP) 223 mii->mii_media_active |= IFM_LOOP; 224 225 if (bmcr & BMCR_AUTOEN) { 226 /* 227 * The PAR status bits are only valid if autonegotiation 228 * has completed (or it's disabled). 229 */ 230 if ((bmsr & BMSR_ACOMP) == 0) { 231 /* Erg, still trying, I guess... */ 232 mii->mii_media_active |= IFM_NONE; 233 return; 234 } 235 236 /* 237 * Argh. The PAR doesn't seem to indicate duplex mode 238 * properly! Determine media based on link partner's 239 * advertised capabilities. 240 */ 241 if (PHY_READ(sc, MII_ANER) & ANER_LPAN) { 242 anlpar = PHY_READ(sc, MII_ANAR) & 243 PHY_READ(sc, MII_ANLPAR); 244 if (anlpar & ANLPAR_TX_FD) 245 mii->mii_media_active |= IFM_100_TX|IFM_FDX; 246 else if (anlpar & ANLPAR_T4) 247 mii->mii_media_active |= IFM_100_T4|IFM_HDX; 248 else if (anlpar & ANLPAR_TX) 249 mii->mii_media_active |= IFM_100_TX|IFM_HDX; 250 else if (anlpar & ANLPAR_10_FD) 251 mii->mii_media_active |= IFM_10_T|IFM_FDX; 252 else if (anlpar & ANLPAR_10) 253 mii->mii_media_active |= IFM_10_T|IFM_HDX; 254 else 255 mii->mii_media_active |= IFM_NONE; 256 if ((mii->mii_media_active & IFM_FDX) != 0) 257 mii->mii_media_active |= 258 mii_phy_flowstatus(sc); 259 return; 260 } 261 262 /* 263 * Link partner is not capable of autonegotiation. 264 * We will never be in full-duplex mode if this is 265 * the case, so reading the PAR is OK. 266 */ 267 par = PHY_READ(sc, MII_NSPHY_PAR); 268 if (par & PAR_10) 269 mii->mii_media_active |= IFM_10_T; 270 else 271 mii->mii_media_active |= IFM_100_TX; 272 mii->mii_media_active |= IFM_HDX; 273 } else 274 mii->mii_media_active = ife->ifm_media; 275 } 276 277 static void 278 nsphy_reset(struct mii_softc *sc) 279 { 280 struct ifmedia_entry *ife = sc->mii_pdata->mii_media.ifm_cur; 281 int reg, i; 282 283 if (sc->mii_flags & MIIF_NOISOLATE) 284 reg = BMCR_RESET; 285 else 286 reg = BMCR_RESET | BMCR_ISO; 287 PHY_WRITE(sc, MII_BMCR, reg); 288 289 /* 290 * It is best to allow a little time for the reset to settle 291 * in before we start polling the BMCR again. Notably, the 292 * DP83840A manuals state that there should be a 500us delay 293 * between asserting software reset and attempting MII serial 294 * operations. Be conservative. 295 */ 296 DELAY(1000); 297 298 /* 299 * Wait another 2s for it to complete. 300 * This is only a little overkill as under normal circumstances 301 * the PHY can take up to 1s to complete reset. 302 * This is also a bit odd because after a reset, the BMCR will 303 * clear the reset bit and simply reports 0 even though the reset 304 * is not yet complete. 305 */ 306 for (i = 0; i < 1000; i++) { 307 reg = PHY_READ(sc, MII_BMCR); 308 if (reg != 0 && (reg & BMCR_RESET) == 0) 309 break; 310 DELAY(2000); 311 } 312 313 if ((sc->mii_flags & MIIF_NOISOLATE) == 0) { 314 if ((ife == NULL && sc->mii_inst != 0) || 315 (ife != NULL && IFM_INST(ife->ifm_media) != sc->mii_inst)) 316 PHY_WRITE(sc, MII_BMCR, reg | BMCR_ISO); 317 } 318 } 319