1 /* $NetBSD: icsphyreg.h,v 1.2 2003/07/01 22:46:08 msaitoh Exp $ */ 2 3 /*- 4 * Copyright (c) 1998 The NetBSD Foundation, Inc. 5 * All rights reserved. 6 * 7 * This code is derived from software contributed to The NetBSD Foundation 8 * by Jason R. Thorpe of the Numerical Aerospace Simulation Facility, 9 * NASA Ames Research Center. 10 * 11 * Redistribution and use in source and binary forms, with or without 12 * modification, are permitted provided that the following conditions 13 * are met: 14 * 1. Redistributions of source code must retain the above copyright 15 * notice, this list of conditions and the following disclaimer. 16 * 2. Redistributions in binary form must reproduce the above copyright 17 * notice, this list of conditions and the following disclaimer in the 18 * documentation and/or other materials provided with the distribution. 19 * 20 * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS 21 * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED 22 * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR 23 * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS 24 * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 30 * POSSIBILITY OF SUCH DAMAGE. 31 * 32 * $FreeBSD$ 33 */ 34 35 #ifndef _DEV_MII_ICSPHYREG_H_ 36 #define _DEV_MII_ICSPHYREG_H_ 37 38 /* 39 * ICS1890 registers. 40 * http://www.icst.com/pdf/18??.pdf 41 */ 42 43 /* HEX 1889 1890 1892 1893 44 *-------------------------------------------------------------- 45 * 0 Control * * * * 46 * 1 Status * * * * 47 * 2 PHY Identifier * * * * 48 * 3 PHY Identifier * * * * 49 * 4 Auto-Neg. Advertisement * * * 50 * 5 Auto-Neg. Link Parent Adv * * * 51 * 6 Auto-Neg. Expansion * * * 52 * 7 Auto-Neg. Next Page Tx * * 53 * 8 ANg Nxt Page Lnk Parnt Abl * * 54 * 10 Extended Control * * * * 55 * 11 Quick Poll Status * * * * 56 * 12 10Base-T Operation * * * 57 * 13 Extended Control2 * * * 58 */ 59 60 #define MII_ICSPHY_ECR 0x10 /* Extended Control Register */ 61 #define ECR_OVR 0x8000 /* disable command reg overwrites */ 62 #define ECR_PHYADDR_MASK 0x07c0 /* PHY address mask */ 63 #define ECR_CTEST 0x0020 /* Stream Cipher Test Mode */ 64 #define ECR_IECT 0x0004 /* Invalid Error Code Test */ 65 #define ECR_SSD 0x0001 /* Stream Cipher Disable */ 66 67 #define MII_ICSPHY_QPR 0x11 /* Quick Poll Register */ 68 #define QPR_SPEED 0x8000 /* 100Mbps */ 69 #define QPR_FDX 0x4000 /* Full dupled */ 70 #define QPR_ANB2 0x2000 /* Autoneg monitor bit 2 */ 71 #define QPR_ANB1 0x1000 /* Autoneg monitor bit 1 */ 72 #define QPR_ANB0 0x0800 /* Autoneg monitor bit 0 */ 73 #define QPR_RXERR 0x0400 /* Receive signal lost */ 74 #define QPR_PLLERR 0x0200 /* PLL error */ 75 #define QPR_FCARR 0x0100 /* False carrier detected */ 76 #define QPR_INVALSYM 0x0080 /* Invalid Symbol Detected */ 77 #define QPR_HALT 0x0040 /* Halt Symbol Detected */ 78 #define QPR_PREEM 0x0020 /* Two Idle Symbols together */ 79 #define QPR_ACOMP 0x0010 /* Autonegotiation complete */ 80 #define QPR_SDETECT 0x0008 /* signal detect */ 81 #define QPR_JABBER 0x0004 /* Jabber detected */ 82 #define QPR_RFAULT 0x0002 /* Remote Fault */ 83 #define QPR_LINK 0x0001 /* Link */ 84 85 #define MII_ICSPHY_TTR 0x12 /* 10baseT Operations Register */ 86 #define TTR_RJABBER 0x8000 /* Remote Jabber */ 87 #define TTR_POLARITY 0x4000 /* Polarity Reversed */ 88 #define TTR_NOJABBER 0x0020 /* Disable Jabber Check */ 89 #define TTR_LOOP 0x0010 /* Loopback mode */ 90 #define TTR_NOAPOLARITY 0x0008 /* Disable auto polarity correction */ 91 #define TTR_NOSQE 0x0004 /* Disable SQE check */ 92 #define TTR_NOLINK 0x0002 /* Disable Link check */ 93 #define TTR_NOSQUELCH 0x0001 /* Disable squelch */ 94 95 96 /* 97 * Extended Control Register 2 98 * 99 * HEX 1889 1890 1892 1893 100 *------------------------------------------------------------------- 101 * 8000 Node/Repeater Mode * * * 102 * 4000 Hardware/Software Mode * * * 103 * 2000 Link Partner Support Remote Flt * 104 * 2000 Remote Fault * * 105 * 1000 106 * 0800 107 * 0400 Xmitted Remote Fault status * 108 * 0200 109 * 0100 110 * 0080 Tri-state Enable * 111 * 0040 112 * 0020 113 * 0010 A-N Powerup Remote Flt * 114 * 0008 115 * 0004 116 * 0002 Automatic 10Base-T Power Down * 117 * 0001 Automatic 100Base-TX Power Down * * * 118 */ 119 120 #define MII_ICSPHY_ECR2 0x13 /* Extended Control Register 2 */ 121 #define ECR2_REPEATER 0x8000 /* Repeater Mode */ 122 #define ECR2_HWSW 0x4000 /* hw/sw config priority */ 123 #define ECR2_LPRF 0x2000 /* link partner supports rem fault */ 124 #define ECR2_FORCERF 0x0400 /* Force transmit of rem fault */ 125 #define ECR2_RFPUP 0x0010 /* A-N Powerup Remote fault */ 126 #define ECR2_10AUTOPWRDN 0x0002 /* Automatic 10baseT power down */ 127 #define ECR2_100AUTOPWRDN 0x0001 /* Automatic 100baseTX power down */ 128 129 #endif /* _DEV_MII_ICSPHYREG_H_ */ 130