1 /****************************************************************************** 2 3 Copyright (c) 2001-2013, Intel Corporation 4 All rights reserved. 5 6 Redistribution and use in source and binary forms, with or without 7 modification, are permitted provided that the following conditions are met: 8 9 1. Redistributions of source code must retain the above copyright notice, 10 this list of conditions and the following disclaimer. 11 12 2. Redistributions in binary form must reproduce the above copyright 13 notice, this list of conditions and the following disclaimer in the 14 documentation and/or other materials provided with the distribution. 15 16 3. Neither the name of the Intel Corporation nor the names of its 17 contributors may be used to endorse or promote products derived from 18 this software without specific prior written permission. 19 20 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 21 AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE 24 LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 30 POSSIBILITY OF SUCH DAMAGE. 31 32 ******************************************************************************/ 33 /*$FreeBSD$*/ 34 35 #include "ixgbe_type.h" 36 #include "ixgbe_82598.h" 37 #include "ixgbe_api.h" 38 #include "ixgbe_common.h" 39 #include "ixgbe_phy.h" 40 41 static s32 ixgbe_get_link_capabilities_82598(struct ixgbe_hw *hw, 42 ixgbe_link_speed *speed, 43 bool *autoneg); 44 static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw); 45 static s32 ixgbe_start_mac_link_82598(struct ixgbe_hw *hw, 46 bool autoneg_wait_to_complete); 47 static s32 ixgbe_check_mac_link_82598(struct ixgbe_hw *hw, 48 ixgbe_link_speed *speed, bool *link_up, 49 bool link_up_wait_to_complete); 50 static s32 ixgbe_setup_mac_link_82598(struct ixgbe_hw *hw, 51 ixgbe_link_speed speed, 52 bool autoneg_wait_to_complete); 53 static s32 ixgbe_setup_copper_link_82598(struct ixgbe_hw *hw, 54 ixgbe_link_speed speed, 55 bool autoneg_wait_to_complete); 56 static s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw); 57 static s32 ixgbe_clear_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq); 58 static s32 ixgbe_clear_vfta_82598(struct ixgbe_hw *hw); 59 static void ixgbe_set_rxpba_82598(struct ixgbe_hw *hw, int num_pb, 60 u32 headroom, int strategy); 61 static s32 ixgbe_read_i2c_sff8472_82598(struct ixgbe_hw *hw, u8 byte_offset, 62 u8 *sff8472_data); 63 /** 64 * ixgbe_set_pcie_completion_timeout - set pci-e completion timeout 65 * @hw: pointer to the HW structure 66 * 67 * The defaults for 82598 should be in the range of 50us to 50ms, 68 * however the hardware default for these parts is 500us to 1ms which is less 69 * than the 10ms recommended by the pci-e spec. To address this we need to 70 * increase the value to either 10ms to 250ms for capability version 1 config, 71 * or 16ms to 55ms for version 2. 72 **/ 73 void ixgbe_set_pcie_completion_timeout(struct ixgbe_hw *hw) 74 { 75 u32 gcr = IXGBE_READ_REG(hw, IXGBE_GCR); 76 u16 pcie_devctl2; 77 78 /* only take action if timeout value is defaulted to 0 */ 79 if (gcr & IXGBE_GCR_CMPL_TMOUT_MASK) 80 goto out; 81 82 /* 83 * if capababilities version is type 1 we can write the 84 * timeout of 10ms to 250ms through the GCR register 85 */ 86 if (!(gcr & IXGBE_GCR_CAP_VER2)) { 87 gcr |= IXGBE_GCR_CMPL_TMOUT_10ms; 88 goto out; 89 } 90 91 /* 92 * for version 2 capabilities we need to write the config space 93 * directly in order to set the completion timeout value for 94 * 16ms to 55ms 95 */ 96 pcie_devctl2 = IXGBE_READ_PCIE_WORD(hw, IXGBE_PCI_DEVICE_CONTROL2); 97 pcie_devctl2 |= IXGBE_PCI_DEVICE_CONTROL2_16ms; 98 IXGBE_WRITE_PCIE_WORD(hw, IXGBE_PCI_DEVICE_CONTROL2, pcie_devctl2); 99 out: 100 /* disable completion timeout resend */ 101 gcr &= ~IXGBE_GCR_CMPL_TMOUT_RESEND; 102 IXGBE_WRITE_REG(hw, IXGBE_GCR, gcr); 103 } 104 105 /** 106 * ixgbe_init_ops_82598 - Inits func ptrs and MAC type 107 * @hw: pointer to hardware structure 108 * 109 * Initialize the function pointers and assign the MAC type for 82598. 110 * Does not touch the hardware. 111 **/ 112 s32 ixgbe_init_ops_82598(struct ixgbe_hw *hw) 113 { 114 struct ixgbe_mac_info *mac = &hw->mac; 115 struct ixgbe_phy_info *phy = &hw->phy; 116 s32 ret_val; 117 118 DEBUGFUNC("ixgbe_init_ops_82598"); 119 120 ret_val = ixgbe_init_phy_ops_generic(hw); 121 ret_val = ixgbe_init_ops_generic(hw); 122 123 /* PHY */ 124 phy->ops.init = &ixgbe_init_phy_ops_82598; 125 126 /* MAC */ 127 mac->ops.start_hw = &ixgbe_start_hw_82598; 128 mac->ops.enable_relaxed_ordering = &ixgbe_enable_relaxed_ordering_82598; 129 mac->ops.reset_hw = &ixgbe_reset_hw_82598; 130 mac->ops.get_media_type = &ixgbe_get_media_type_82598; 131 mac->ops.get_supported_physical_layer = 132 &ixgbe_get_supported_physical_layer_82598; 133 mac->ops.read_analog_reg8 = &ixgbe_read_analog_reg8_82598; 134 mac->ops.write_analog_reg8 = &ixgbe_write_analog_reg8_82598; 135 mac->ops.set_lan_id = &ixgbe_set_lan_id_multi_port_pcie_82598; 136 137 /* RAR, Multicast, VLAN */ 138 mac->ops.set_vmdq = &ixgbe_set_vmdq_82598; 139 mac->ops.clear_vmdq = &ixgbe_clear_vmdq_82598; 140 mac->ops.set_vfta = &ixgbe_set_vfta_82598; 141 mac->ops.set_vlvf = NULL; 142 mac->ops.clear_vfta = &ixgbe_clear_vfta_82598; 143 144 /* Flow Control */ 145 mac->ops.fc_enable = &ixgbe_fc_enable_82598; 146 147 mac->mcft_size = 128; 148 mac->vft_size = 128; 149 mac->num_rar_entries = 16; 150 mac->rx_pb_size = 512; 151 mac->max_tx_queues = 32; 152 mac->max_rx_queues = 64; 153 mac->max_msix_vectors = ixgbe_get_pcie_msix_count_generic(hw); 154 155 /* SFP+ Module */ 156 phy->ops.read_i2c_eeprom = &ixgbe_read_i2c_eeprom_82598; 157 phy->ops.read_i2c_sff8472 = &ixgbe_read_i2c_sff8472_82598; 158 159 /* Link */ 160 mac->ops.check_link = &ixgbe_check_mac_link_82598; 161 mac->ops.setup_link = &ixgbe_setup_mac_link_82598; 162 mac->ops.flap_tx_laser = NULL; 163 mac->ops.get_link_capabilities = &ixgbe_get_link_capabilities_82598; 164 mac->ops.setup_rxpba = &ixgbe_set_rxpba_82598; 165 166 /* Manageability interface */ 167 mac->ops.set_fw_drv_ver = NULL; 168 169 return ret_val; 170 } 171 172 /** 173 * ixgbe_init_phy_ops_82598 - PHY/SFP specific init 174 * @hw: pointer to hardware structure 175 * 176 * Initialize any function pointers that were not able to be 177 * set during init_shared_code because the PHY/SFP type was 178 * not known. Perform the SFP init if necessary. 179 * 180 **/ 181 s32 ixgbe_init_phy_ops_82598(struct ixgbe_hw *hw) 182 { 183 struct ixgbe_mac_info *mac = &hw->mac; 184 struct ixgbe_phy_info *phy = &hw->phy; 185 s32 ret_val = IXGBE_SUCCESS; 186 u16 list_offset, data_offset; 187 188 DEBUGFUNC("ixgbe_init_phy_ops_82598"); 189 190 /* Identify the PHY */ 191 phy->ops.identify(hw); 192 193 /* Overwrite the link function pointers if copper PHY */ 194 if (mac->ops.get_media_type(hw) == ixgbe_media_type_copper) { 195 mac->ops.setup_link = &ixgbe_setup_copper_link_82598; 196 mac->ops.get_link_capabilities = 197 &ixgbe_get_copper_link_capabilities_generic; 198 } 199 200 switch (hw->phy.type) { 201 case ixgbe_phy_tn: 202 phy->ops.setup_link = &ixgbe_setup_phy_link_tnx; 203 phy->ops.check_link = &ixgbe_check_phy_link_tnx; 204 phy->ops.get_firmware_version = 205 &ixgbe_get_phy_firmware_version_tnx; 206 break; 207 case ixgbe_phy_nl: 208 phy->ops.reset = &ixgbe_reset_phy_nl; 209 210 /* Call SFP+ identify routine to get the SFP+ module type */ 211 ret_val = phy->ops.identify_sfp(hw); 212 if (ret_val != IXGBE_SUCCESS) 213 goto out; 214 else if (hw->phy.sfp_type == ixgbe_sfp_type_unknown) { 215 ret_val = IXGBE_ERR_SFP_NOT_SUPPORTED; 216 goto out; 217 } 218 219 /* Check to see if SFP+ module is supported */ 220 ret_val = ixgbe_get_sfp_init_sequence_offsets(hw, 221 &list_offset, 222 &data_offset); 223 if (ret_val != IXGBE_SUCCESS) { 224 ret_val = IXGBE_ERR_SFP_NOT_SUPPORTED; 225 goto out; 226 } 227 break; 228 default: 229 break; 230 } 231 232 out: 233 return ret_val; 234 } 235 236 /** 237 * ixgbe_start_hw_82598 - Prepare hardware for Tx/Rx 238 * @hw: pointer to hardware structure 239 * 240 * Starts the hardware using the generic start_hw function. 241 * Disables relaxed ordering Then set pcie completion timeout 242 * 243 **/ 244 s32 ixgbe_start_hw_82598(struct ixgbe_hw *hw) 245 { 246 u32 regval; 247 u32 i; 248 s32 ret_val = IXGBE_SUCCESS; 249 250 DEBUGFUNC("ixgbe_start_hw_82598"); 251 252 ret_val = ixgbe_start_hw_generic(hw); 253 254 /* Disable relaxed ordering */ 255 for (i = 0; ((i < hw->mac.max_tx_queues) && 256 (i < IXGBE_DCA_MAX_QUEUES_82598)); i++) { 257 regval = IXGBE_READ_REG(hw, IXGBE_DCA_TXCTRL(i)); 258 regval &= ~IXGBE_DCA_TXCTRL_DESC_WRO_EN; 259 IXGBE_WRITE_REG(hw, IXGBE_DCA_TXCTRL(i), regval); 260 } 261 262 for (i = 0; ((i < hw->mac.max_rx_queues) && 263 (i < IXGBE_DCA_MAX_QUEUES_82598)); i++) { 264 regval = IXGBE_READ_REG(hw, IXGBE_DCA_RXCTRL(i)); 265 regval &= ~(IXGBE_DCA_RXCTRL_DATA_WRO_EN | 266 IXGBE_DCA_RXCTRL_HEAD_WRO_EN); 267 IXGBE_WRITE_REG(hw, IXGBE_DCA_RXCTRL(i), regval); 268 } 269 270 /* set the completion timeout for interface */ 271 if (ret_val == IXGBE_SUCCESS) 272 ixgbe_set_pcie_completion_timeout(hw); 273 274 return ret_val; 275 } 276 277 /** 278 * ixgbe_get_link_capabilities_82598 - Determines link capabilities 279 * @hw: pointer to hardware structure 280 * @speed: pointer to link speed 281 * @autoneg: boolean auto-negotiation value 282 * 283 * Determines the link capabilities by reading the AUTOC register. 284 **/ 285 static s32 ixgbe_get_link_capabilities_82598(struct ixgbe_hw *hw, 286 ixgbe_link_speed *speed, 287 bool *autoneg) 288 { 289 s32 status = IXGBE_SUCCESS; 290 u32 autoc = 0; 291 292 DEBUGFUNC("ixgbe_get_link_capabilities_82598"); 293 294 /* 295 * Determine link capabilities based on the stored value of AUTOC, 296 * which represents EEPROM defaults. If AUTOC value has not been 297 * stored, use the current register value. 298 */ 299 if (hw->mac.orig_link_settings_stored) 300 autoc = hw->mac.orig_autoc; 301 else 302 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC); 303 304 switch (autoc & IXGBE_AUTOC_LMS_MASK) { 305 case IXGBE_AUTOC_LMS_1G_LINK_NO_AN: 306 *speed = IXGBE_LINK_SPEED_1GB_FULL; 307 *autoneg = FALSE; 308 break; 309 310 case IXGBE_AUTOC_LMS_10G_LINK_NO_AN: 311 *speed = IXGBE_LINK_SPEED_10GB_FULL; 312 *autoneg = FALSE; 313 break; 314 315 case IXGBE_AUTOC_LMS_1G_AN: 316 *speed = IXGBE_LINK_SPEED_1GB_FULL; 317 *autoneg = TRUE; 318 break; 319 320 case IXGBE_AUTOC_LMS_KX4_AN: 321 case IXGBE_AUTOC_LMS_KX4_AN_1G_AN: 322 *speed = IXGBE_LINK_SPEED_UNKNOWN; 323 if (autoc & IXGBE_AUTOC_KX4_SUPP) 324 *speed |= IXGBE_LINK_SPEED_10GB_FULL; 325 if (autoc & IXGBE_AUTOC_KX_SUPP) 326 *speed |= IXGBE_LINK_SPEED_1GB_FULL; 327 *autoneg = TRUE; 328 break; 329 330 default: 331 status = IXGBE_ERR_LINK_SETUP; 332 break; 333 } 334 335 return status; 336 } 337 338 /** 339 * ixgbe_get_media_type_82598 - Determines media type 340 * @hw: pointer to hardware structure 341 * 342 * Returns the media type (fiber, copper, backplane) 343 **/ 344 static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw) 345 { 346 enum ixgbe_media_type media_type; 347 348 DEBUGFUNC("ixgbe_get_media_type_82598"); 349 350 /* Detect if there is a copper PHY attached. */ 351 switch (hw->phy.type) { 352 case ixgbe_phy_cu_unknown: 353 case ixgbe_phy_tn: 354 media_type = ixgbe_media_type_copper; 355 goto out; 356 default: 357 break; 358 } 359 360 /* Media type for I82598 is based on device ID */ 361 switch (hw->device_id) { 362 case IXGBE_DEV_ID_82598: 363 case IXGBE_DEV_ID_82598_BX: 364 /* Default device ID is mezzanine card KX/KX4 */ 365 media_type = ixgbe_media_type_backplane; 366 break; 367 case IXGBE_DEV_ID_82598AF_DUAL_PORT: 368 case IXGBE_DEV_ID_82598AF_SINGLE_PORT: 369 case IXGBE_DEV_ID_82598_DA_DUAL_PORT: 370 case IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM: 371 case IXGBE_DEV_ID_82598EB_XF_LR: 372 case IXGBE_DEV_ID_82598EB_SFP_LOM: 373 media_type = ixgbe_media_type_fiber; 374 break; 375 case IXGBE_DEV_ID_82598EB_CX4: 376 case IXGBE_DEV_ID_82598_CX4_DUAL_PORT: 377 media_type = ixgbe_media_type_cx4; 378 break; 379 case IXGBE_DEV_ID_82598AT: 380 case IXGBE_DEV_ID_82598AT2: 381 media_type = ixgbe_media_type_copper; 382 break; 383 default: 384 media_type = ixgbe_media_type_unknown; 385 break; 386 } 387 out: 388 return media_type; 389 } 390 391 /** 392 * ixgbe_fc_enable_82598 - Enable flow control 393 * @hw: pointer to hardware structure 394 * 395 * Enable flow control according to the current settings. 396 **/ 397 s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw) 398 { 399 s32 ret_val = IXGBE_SUCCESS; 400 u32 fctrl_reg; 401 u32 rmcs_reg; 402 u32 reg; 403 u32 fcrtl, fcrth; 404 u32 link_speed = 0; 405 int i; 406 bool link_up; 407 408 DEBUGFUNC("ixgbe_fc_enable_82598"); 409 410 /* Validate the water mark configuration */ 411 if (!hw->fc.pause_time) { 412 ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; 413 goto out; 414 } 415 416 /* Low water mark of zero causes XOFF floods */ 417 for (i = 0; i < IXGBE_DCB_MAX_TRAFFIC_CLASS; i++) { 418 if ((hw->fc.current_mode & ixgbe_fc_tx_pause) && 419 hw->fc.high_water[i]) { 420 if (!hw->fc.low_water[i] || 421 hw->fc.low_water[i] >= hw->fc.high_water[i]) { 422 DEBUGOUT("Invalid water mark configuration\n"); 423 ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS; 424 goto out; 425 } 426 } 427 } 428 429 /* 430 * On 82598 having Rx FC on causes resets while doing 1G 431 * so if it's on turn it off once we know link_speed. For 432 * more details see 82598 Specification update. 433 */ 434 hw->mac.ops.check_link(hw, &link_speed, &link_up, FALSE); 435 if (link_up && link_speed == IXGBE_LINK_SPEED_1GB_FULL) { 436 switch (hw->fc.requested_mode) { 437 case ixgbe_fc_full: 438 hw->fc.requested_mode = ixgbe_fc_tx_pause; 439 break; 440 case ixgbe_fc_rx_pause: 441 hw->fc.requested_mode = ixgbe_fc_none; 442 break; 443 default: 444 /* no change */ 445 break; 446 } 447 } 448 449 /* Negotiate the fc mode to use */ 450 ixgbe_fc_autoneg(hw); 451 452 /* Disable any previous flow control settings */ 453 fctrl_reg = IXGBE_READ_REG(hw, IXGBE_FCTRL); 454 fctrl_reg &= ~(IXGBE_FCTRL_RFCE | IXGBE_FCTRL_RPFCE); 455 456 rmcs_reg = IXGBE_READ_REG(hw, IXGBE_RMCS); 457 rmcs_reg &= ~(IXGBE_RMCS_TFCE_PRIORITY | IXGBE_RMCS_TFCE_802_3X); 458 459 /* 460 * The possible values of fc.current_mode are: 461 * 0: Flow control is completely disabled 462 * 1: Rx flow control is enabled (we can receive pause frames, 463 * but not send pause frames). 464 * 2: Tx flow control is enabled (we can send pause frames but 465 * we do not support receiving pause frames). 466 * 3: Both Rx and Tx flow control (symmetric) are enabled. 467 * other: Invalid. 468 */ 469 switch (hw->fc.current_mode) { 470 case ixgbe_fc_none: 471 /* 472 * Flow control is disabled by software override or autoneg. 473 * The code below will actually disable it in the HW. 474 */ 475 break; 476 case ixgbe_fc_rx_pause: 477 /* 478 * Rx Flow control is enabled and Tx Flow control is 479 * disabled by software override. Since there really 480 * isn't a way to advertise that we are capable of RX 481 * Pause ONLY, we will advertise that we support both 482 * symmetric and asymmetric Rx PAUSE. Later, we will 483 * disable the adapter's ability to send PAUSE frames. 484 */ 485 fctrl_reg |= IXGBE_FCTRL_RFCE; 486 break; 487 case ixgbe_fc_tx_pause: 488 /* 489 * Tx Flow control is enabled, and Rx Flow control is 490 * disabled by software override. 491 */ 492 rmcs_reg |= IXGBE_RMCS_TFCE_802_3X; 493 break; 494 case ixgbe_fc_full: 495 /* Flow control (both Rx and Tx) is enabled by SW override. */ 496 fctrl_reg |= IXGBE_FCTRL_RFCE; 497 rmcs_reg |= IXGBE_RMCS_TFCE_802_3X; 498 break; 499 default: 500 DEBUGOUT("Flow control param set incorrectly\n"); 501 ret_val = IXGBE_ERR_CONFIG; 502 goto out; 503 break; 504 } 505 506 /* Set 802.3x based flow control settings. */ 507 fctrl_reg |= IXGBE_FCTRL_DPF; 508 IXGBE_WRITE_REG(hw, IXGBE_FCTRL, fctrl_reg); 509 IXGBE_WRITE_REG(hw, IXGBE_RMCS, rmcs_reg); 510 511 /* Set up and enable Rx high/low water mark thresholds, enable XON. */ 512 for (i = 0; i < IXGBE_DCB_MAX_TRAFFIC_CLASS; i++) { 513 if ((hw->fc.current_mode & ixgbe_fc_tx_pause) && 514 hw->fc.high_water[i]) { 515 fcrtl = (hw->fc.low_water[i] << 10) | IXGBE_FCRTL_XONE; 516 fcrth = (hw->fc.high_water[i] << 10) | IXGBE_FCRTH_FCEN; 517 IXGBE_WRITE_REG(hw, IXGBE_FCRTL(i), fcrtl); 518 IXGBE_WRITE_REG(hw, IXGBE_FCRTH(i), fcrth); 519 } else { 520 IXGBE_WRITE_REG(hw, IXGBE_FCRTL(i), 0); 521 IXGBE_WRITE_REG(hw, IXGBE_FCRTH(i), 0); 522 } 523 524 } 525 526 /* Configure pause time (2 TCs per register) */ 527 reg = hw->fc.pause_time * 0x00010001; 528 for (i = 0; i < (IXGBE_DCB_MAX_TRAFFIC_CLASS / 2); i++) 529 IXGBE_WRITE_REG(hw, IXGBE_FCTTV(i), reg); 530 531 /* Configure flow control refresh threshold value */ 532 IXGBE_WRITE_REG(hw, IXGBE_FCRTV, hw->fc.pause_time / 2); 533 534 out: 535 return ret_val; 536 } 537 538 /** 539 * ixgbe_start_mac_link_82598 - Configures MAC link settings 540 * @hw: pointer to hardware structure 541 * 542 * Configures link settings based on values in the ixgbe_hw struct. 543 * Restarts the link. Performs autonegotiation if needed. 544 **/ 545 static s32 ixgbe_start_mac_link_82598(struct ixgbe_hw *hw, 546 bool autoneg_wait_to_complete) 547 { 548 u32 autoc_reg; 549 u32 links_reg; 550 u32 i; 551 s32 status = IXGBE_SUCCESS; 552 553 DEBUGFUNC("ixgbe_start_mac_link_82598"); 554 555 /* Restart link */ 556 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); 557 autoc_reg |= IXGBE_AUTOC_AN_RESTART; 558 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc_reg); 559 560 /* Only poll for autoneg to complete if specified to do so */ 561 if (autoneg_wait_to_complete) { 562 if ((autoc_reg & IXGBE_AUTOC_LMS_MASK) == 563 IXGBE_AUTOC_LMS_KX4_AN || 564 (autoc_reg & IXGBE_AUTOC_LMS_MASK) == 565 IXGBE_AUTOC_LMS_KX4_AN_1G_AN) { 566 links_reg = 0; /* Just in case Autoneg time = 0 */ 567 for (i = 0; i < IXGBE_AUTO_NEG_TIME; i++) { 568 links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS); 569 if (links_reg & IXGBE_LINKS_KX_AN_COMP) 570 break; 571 msec_delay(100); 572 } 573 if (!(links_reg & IXGBE_LINKS_KX_AN_COMP)) { 574 status = IXGBE_ERR_AUTONEG_NOT_COMPLETE; 575 DEBUGOUT("Autonegotiation did not complete.\n"); 576 } 577 } 578 } 579 580 /* Add delay to filter out noises during initial link setup */ 581 msec_delay(50); 582 583 return status; 584 } 585 586 /** 587 * ixgbe_validate_link_ready - Function looks for phy link 588 * @hw: pointer to hardware structure 589 * 590 * Function indicates success when phy link is available. If phy is not ready 591 * within 5 seconds of MAC indicating link, the function returns error. 592 **/ 593 static s32 ixgbe_validate_link_ready(struct ixgbe_hw *hw) 594 { 595 u32 timeout; 596 u16 an_reg; 597 598 if (hw->device_id != IXGBE_DEV_ID_82598AT2) 599 return IXGBE_SUCCESS; 600 601 for (timeout = 0; 602 timeout < IXGBE_VALIDATE_LINK_READY_TIMEOUT; timeout++) { 603 hw->phy.ops.read_reg(hw, IXGBE_MDIO_AUTO_NEG_STATUS, 604 IXGBE_MDIO_AUTO_NEG_DEV_TYPE, &an_reg); 605 606 if ((an_reg & IXGBE_MII_AUTONEG_COMPLETE) && 607 (an_reg & IXGBE_MII_AUTONEG_LINK_UP)) 608 break; 609 610 msec_delay(100); 611 } 612 613 if (timeout == IXGBE_VALIDATE_LINK_READY_TIMEOUT) { 614 DEBUGOUT("Link was indicated but link is down\n"); 615 return IXGBE_ERR_LINK_SETUP; 616 } 617 618 return IXGBE_SUCCESS; 619 } 620 621 /** 622 * ixgbe_check_mac_link_82598 - Get link/speed status 623 * @hw: pointer to hardware structure 624 * @speed: pointer to link speed 625 * @link_up: TRUE is link is up, FALSE otherwise 626 * @link_up_wait_to_complete: bool used to wait for link up or not 627 * 628 * Reads the links register to determine if link is up and the current speed 629 **/ 630 static s32 ixgbe_check_mac_link_82598(struct ixgbe_hw *hw, 631 ixgbe_link_speed *speed, bool *link_up, 632 bool link_up_wait_to_complete) 633 { 634 u32 links_reg; 635 u32 i; 636 u16 link_reg, adapt_comp_reg; 637 638 DEBUGFUNC("ixgbe_check_mac_link_82598"); 639 640 /* 641 * SERDES PHY requires us to read link status from undocumented 642 * register 0xC79F. Bit 0 set indicates link is up/ready; clear 643 * indicates link down. OxC00C is read to check that the XAUI lanes 644 * are active. Bit 0 clear indicates active; set indicates inactive. 645 */ 646 if (hw->phy.type == ixgbe_phy_nl) { 647 hw->phy.ops.read_reg(hw, 0xC79F, IXGBE_TWINAX_DEV, &link_reg); 648 hw->phy.ops.read_reg(hw, 0xC79F, IXGBE_TWINAX_DEV, &link_reg); 649 hw->phy.ops.read_reg(hw, 0xC00C, IXGBE_TWINAX_DEV, 650 &adapt_comp_reg); 651 if (link_up_wait_to_complete) { 652 for (i = 0; i < IXGBE_LINK_UP_TIME; i++) { 653 if ((link_reg & 1) && 654 ((adapt_comp_reg & 1) == 0)) { 655 *link_up = TRUE; 656 break; 657 } else { 658 *link_up = FALSE; 659 } 660 msec_delay(100); 661 hw->phy.ops.read_reg(hw, 0xC79F, 662 IXGBE_TWINAX_DEV, 663 &link_reg); 664 hw->phy.ops.read_reg(hw, 0xC00C, 665 IXGBE_TWINAX_DEV, 666 &adapt_comp_reg); 667 } 668 } else { 669 if ((link_reg & 1) && ((adapt_comp_reg & 1) == 0)) 670 *link_up = TRUE; 671 else 672 *link_up = FALSE; 673 } 674 675 if (*link_up == FALSE) 676 goto out; 677 } 678 679 links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS); 680 if (link_up_wait_to_complete) { 681 for (i = 0; i < IXGBE_LINK_UP_TIME; i++) { 682 if (links_reg & IXGBE_LINKS_UP) { 683 *link_up = TRUE; 684 break; 685 } else { 686 *link_up = FALSE; 687 } 688 msec_delay(100); 689 links_reg = IXGBE_READ_REG(hw, IXGBE_LINKS); 690 } 691 } else { 692 if (links_reg & IXGBE_LINKS_UP) 693 *link_up = TRUE; 694 else 695 *link_up = FALSE; 696 } 697 698 if (links_reg & IXGBE_LINKS_SPEED) 699 *speed = IXGBE_LINK_SPEED_10GB_FULL; 700 else 701 *speed = IXGBE_LINK_SPEED_1GB_FULL; 702 703 if ((hw->device_id == IXGBE_DEV_ID_82598AT2) && (*link_up == TRUE) && 704 (ixgbe_validate_link_ready(hw) != IXGBE_SUCCESS)) 705 *link_up = FALSE; 706 707 out: 708 return IXGBE_SUCCESS; 709 } 710 711 /** 712 * ixgbe_setup_mac_link_82598 - Set MAC link speed 713 * @hw: pointer to hardware structure 714 * @speed: new link speed 715 * @autoneg_wait_to_complete: TRUE when waiting for completion is needed 716 * 717 * Set the link speed in the AUTOC register and restarts link. 718 **/ 719 static s32 ixgbe_setup_mac_link_82598(struct ixgbe_hw *hw, 720 ixgbe_link_speed speed, 721 bool autoneg_wait_to_complete) 722 { 723 bool autoneg = FALSE; 724 s32 status = IXGBE_SUCCESS; 725 ixgbe_link_speed link_capabilities = IXGBE_LINK_SPEED_UNKNOWN; 726 u32 curr_autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC); 727 u32 autoc = curr_autoc; 728 u32 link_mode = autoc & IXGBE_AUTOC_LMS_MASK; 729 730 DEBUGFUNC("ixgbe_setup_mac_link_82598"); 731 732 /* Check to see if speed passed in is supported. */ 733 ixgbe_get_link_capabilities(hw, &link_capabilities, &autoneg); 734 speed &= link_capabilities; 735 736 if (speed == IXGBE_LINK_SPEED_UNKNOWN) 737 status = IXGBE_ERR_LINK_SETUP; 738 739 /* Set KX4/KX support according to speed requested */ 740 else if (link_mode == IXGBE_AUTOC_LMS_KX4_AN || 741 link_mode == IXGBE_AUTOC_LMS_KX4_AN_1G_AN) { 742 autoc &= ~IXGBE_AUTOC_KX4_KX_SUPP_MASK; 743 if (speed & IXGBE_LINK_SPEED_10GB_FULL) 744 autoc |= IXGBE_AUTOC_KX4_SUPP; 745 if (speed & IXGBE_LINK_SPEED_1GB_FULL) 746 autoc |= IXGBE_AUTOC_KX_SUPP; 747 if (autoc != curr_autoc) 748 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, autoc); 749 } 750 751 if (status == IXGBE_SUCCESS) { 752 /* 753 * Setup and restart the link based on the new values in 754 * ixgbe_hw This will write the AUTOC register based on the new 755 * stored values 756 */ 757 status = ixgbe_start_mac_link_82598(hw, 758 autoneg_wait_to_complete); 759 } 760 761 return status; 762 } 763 764 765 /** 766 * ixgbe_setup_copper_link_82598 - Set the PHY autoneg advertised field 767 * @hw: pointer to hardware structure 768 * @speed: new link speed 769 * @autoneg_wait_to_complete: TRUE if waiting is needed to complete 770 * 771 * Sets the link speed in the AUTOC register in the MAC and restarts link. 772 **/ 773 static s32 ixgbe_setup_copper_link_82598(struct ixgbe_hw *hw, 774 ixgbe_link_speed speed, 775 bool autoneg_wait_to_complete) 776 { 777 s32 status; 778 779 DEBUGFUNC("ixgbe_setup_copper_link_82598"); 780 781 /* Setup the PHY according to input speed */ 782 status = hw->phy.ops.setup_link_speed(hw, speed, 783 autoneg_wait_to_complete); 784 /* Set up MAC */ 785 ixgbe_start_mac_link_82598(hw, autoneg_wait_to_complete); 786 787 return status; 788 } 789 790 /** 791 * ixgbe_reset_hw_82598 - Performs hardware reset 792 * @hw: pointer to hardware structure 793 * 794 * Resets the hardware by resetting the transmit and receive units, masks and 795 * clears all interrupts, performing a PHY reset, and performing a link (MAC) 796 * reset. 797 **/ 798 static s32 ixgbe_reset_hw_82598(struct ixgbe_hw *hw) 799 { 800 s32 status = IXGBE_SUCCESS; 801 s32 phy_status = IXGBE_SUCCESS; 802 u32 ctrl; 803 u32 gheccr; 804 u32 i; 805 u32 autoc; 806 u8 analog_val; 807 808 DEBUGFUNC("ixgbe_reset_hw_82598"); 809 810 /* Call adapter stop to disable tx/rx and clear interrupts */ 811 status = hw->mac.ops.stop_adapter(hw); 812 if (status != IXGBE_SUCCESS) 813 goto reset_hw_out; 814 815 /* 816 * Power up the Atlas Tx lanes if they are currently powered down. 817 * Atlas Tx lanes are powered down for MAC loopback tests, but 818 * they are not automatically restored on reset. 819 */ 820 hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_LPBK, &analog_val); 821 if (analog_val & IXGBE_ATLAS_PDN_TX_REG_EN) { 822 /* Enable Tx Atlas so packets can be transmitted again */ 823 hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_LPBK, 824 &analog_val); 825 analog_val &= ~IXGBE_ATLAS_PDN_TX_REG_EN; 826 hw->mac.ops.write_analog_reg8(hw, IXGBE_ATLAS_PDN_LPBK, 827 analog_val); 828 829 hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_10G, 830 &analog_val); 831 analog_val &= ~IXGBE_ATLAS_PDN_TX_10G_QL_ALL; 832 hw->mac.ops.write_analog_reg8(hw, IXGBE_ATLAS_PDN_10G, 833 analog_val); 834 835 hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_1G, 836 &analog_val); 837 analog_val &= ~IXGBE_ATLAS_PDN_TX_1G_QL_ALL; 838 hw->mac.ops.write_analog_reg8(hw, IXGBE_ATLAS_PDN_1G, 839 analog_val); 840 841 hw->mac.ops.read_analog_reg8(hw, IXGBE_ATLAS_PDN_AN, 842 &analog_val); 843 analog_val &= ~IXGBE_ATLAS_PDN_TX_AN_QL_ALL; 844 hw->mac.ops.write_analog_reg8(hw, IXGBE_ATLAS_PDN_AN, 845 analog_val); 846 } 847 848 /* Reset PHY */ 849 if (hw->phy.reset_disable == FALSE) { 850 /* PHY ops must be identified and initialized prior to reset */ 851 852 /* Init PHY and function pointers, perform SFP setup */ 853 phy_status = hw->phy.ops.init(hw); 854 if (phy_status == IXGBE_ERR_SFP_NOT_SUPPORTED) 855 goto reset_hw_out; 856 if (phy_status == IXGBE_ERR_SFP_NOT_PRESENT) 857 goto mac_reset_top; 858 859 hw->phy.ops.reset(hw); 860 } 861 862 mac_reset_top: 863 /* 864 * Issue global reset to the MAC. This needs to be a SW reset. 865 * If link reset is used, it might reset the MAC when mng is using it 866 */ 867 ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL) | IXGBE_CTRL_RST; 868 IXGBE_WRITE_REG(hw, IXGBE_CTRL, ctrl); 869 IXGBE_WRITE_FLUSH(hw); 870 871 /* Poll for reset bit to self-clear indicating reset is complete */ 872 for (i = 0; i < 10; i++) { 873 usec_delay(1); 874 ctrl = IXGBE_READ_REG(hw, IXGBE_CTRL); 875 if (!(ctrl & IXGBE_CTRL_RST)) 876 break; 877 } 878 if (ctrl & IXGBE_CTRL_RST) { 879 status = IXGBE_ERR_RESET_FAILED; 880 DEBUGOUT("Reset polling failed to complete.\n"); 881 } 882 883 msec_delay(50); 884 885 /* 886 * Double resets are required for recovery from certain error 887 * conditions. Between resets, it is necessary to stall to allow time 888 * for any pending HW events to complete. 889 */ 890 if (hw->mac.flags & IXGBE_FLAGS_DOUBLE_RESET_REQUIRED) { 891 hw->mac.flags &= ~IXGBE_FLAGS_DOUBLE_RESET_REQUIRED; 892 goto mac_reset_top; 893 } 894 895 gheccr = IXGBE_READ_REG(hw, IXGBE_GHECCR); 896 gheccr &= ~((1 << 21) | (1 << 18) | (1 << 9) | (1 << 6)); 897 IXGBE_WRITE_REG(hw, IXGBE_GHECCR, gheccr); 898 899 /* 900 * Store the original AUTOC value if it has not been 901 * stored off yet. Otherwise restore the stored original 902 * AUTOC value since the reset operation sets back to deaults. 903 */ 904 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC); 905 if (hw->mac.orig_link_settings_stored == FALSE) { 906 hw->mac.orig_autoc = autoc; 907 hw->mac.orig_link_settings_stored = TRUE; 908 } else if (autoc != hw->mac.orig_autoc) { 909 IXGBE_WRITE_REG(hw, IXGBE_AUTOC, hw->mac.orig_autoc); 910 } 911 912 /* Store the permanent mac address */ 913 hw->mac.ops.get_mac_addr(hw, hw->mac.perm_addr); 914 915 /* 916 * Store MAC address from RAR0, clear receive address registers, and 917 * clear the multicast table 918 */ 919 hw->mac.ops.init_rx_addrs(hw); 920 921 reset_hw_out: 922 if (phy_status != IXGBE_SUCCESS) 923 status = phy_status; 924 925 return status; 926 } 927 928 /** 929 * ixgbe_set_vmdq_82598 - Associate a VMDq set index with a rx address 930 * @hw: pointer to hardware struct 931 * @rar: receive address register index to associate with a VMDq index 932 * @vmdq: VMDq set index 933 **/ 934 s32 ixgbe_set_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq) 935 { 936 u32 rar_high; 937 u32 rar_entries = hw->mac.num_rar_entries; 938 939 DEBUGFUNC("ixgbe_set_vmdq_82598"); 940 941 /* Make sure we are using a valid rar index range */ 942 if (rar >= rar_entries) { 943 DEBUGOUT1("RAR index %d is out of range.\n", rar); 944 return IXGBE_ERR_INVALID_ARGUMENT; 945 } 946 947 rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(rar)); 948 rar_high &= ~IXGBE_RAH_VIND_MASK; 949 rar_high |= ((vmdq << IXGBE_RAH_VIND_SHIFT) & IXGBE_RAH_VIND_MASK); 950 IXGBE_WRITE_REG(hw, IXGBE_RAH(rar), rar_high); 951 return IXGBE_SUCCESS; 952 } 953 954 /** 955 * ixgbe_clear_vmdq_82598 - Disassociate a VMDq set index from an rx address 956 * @hw: pointer to hardware struct 957 * @rar: receive address register index to associate with a VMDq index 958 * @vmdq: VMDq clear index (not used in 82598, but elsewhere) 959 **/ 960 static s32 ixgbe_clear_vmdq_82598(struct ixgbe_hw *hw, u32 rar, u32 vmdq) 961 { 962 u32 rar_high; 963 u32 rar_entries = hw->mac.num_rar_entries; 964 965 UNREFERENCED_1PARAMETER(vmdq); 966 967 /* Make sure we are using a valid rar index range */ 968 if (rar >= rar_entries) { 969 DEBUGOUT1("RAR index %d is out of range.\n", rar); 970 return IXGBE_ERR_INVALID_ARGUMENT; 971 } 972 973 rar_high = IXGBE_READ_REG(hw, IXGBE_RAH(rar)); 974 if (rar_high & IXGBE_RAH_VIND_MASK) { 975 rar_high &= ~IXGBE_RAH_VIND_MASK; 976 IXGBE_WRITE_REG(hw, IXGBE_RAH(rar), rar_high); 977 } 978 979 return IXGBE_SUCCESS; 980 } 981 982 /** 983 * ixgbe_set_vfta_82598 - Set VLAN filter table 984 * @hw: pointer to hardware structure 985 * @vlan: VLAN id to write to VLAN filter 986 * @vind: VMDq output index that maps queue to VLAN id in VFTA 987 * @vlan_on: boolean flag to turn on/off VLAN in VFTA 988 * 989 * Turn on/off specified VLAN in the VLAN filter table. 990 **/ 991 s32 ixgbe_set_vfta_82598(struct ixgbe_hw *hw, u32 vlan, u32 vind, 992 bool vlan_on) 993 { 994 u32 regindex; 995 u32 bitindex; 996 u32 bits; 997 u32 vftabyte; 998 999 DEBUGFUNC("ixgbe_set_vfta_82598"); 1000 1001 if (vlan > 4095) 1002 return IXGBE_ERR_PARAM; 1003 1004 /* Determine 32-bit word position in array */ 1005 regindex = (vlan >> 5) & 0x7F; /* upper seven bits */ 1006 1007 /* Determine the location of the (VMD) queue index */ 1008 vftabyte = ((vlan >> 3) & 0x03); /* bits (4:3) indicating byte array */ 1009 bitindex = (vlan & 0x7) << 2; /* lower 3 bits indicate nibble */ 1010 1011 /* Set the nibble for VMD queue index */ 1012 bits = IXGBE_READ_REG(hw, IXGBE_VFTAVIND(vftabyte, regindex)); 1013 bits &= (~(0x0F << bitindex)); 1014 bits |= (vind << bitindex); 1015 IXGBE_WRITE_REG(hw, IXGBE_VFTAVIND(vftabyte, regindex), bits); 1016 1017 /* Determine the location of the bit for this VLAN id */ 1018 bitindex = vlan & 0x1F; /* lower five bits */ 1019 1020 bits = IXGBE_READ_REG(hw, IXGBE_VFTA(regindex)); 1021 if (vlan_on) 1022 /* Turn on this VLAN id */ 1023 bits |= (1 << bitindex); 1024 else 1025 /* Turn off this VLAN id */ 1026 bits &= ~(1 << bitindex); 1027 IXGBE_WRITE_REG(hw, IXGBE_VFTA(regindex), bits); 1028 1029 return IXGBE_SUCCESS; 1030 } 1031 1032 /** 1033 * ixgbe_clear_vfta_82598 - Clear VLAN filter table 1034 * @hw: pointer to hardware structure 1035 * 1036 * Clears the VLAN filer table, and the VMDq index associated with the filter 1037 **/ 1038 static s32 ixgbe_clear_vfta_82598(struct ixgbe_hw *hw) 1039 { 1040 u32 offset; 1041 u32 vlanbyte; 1042 1043 DEBUGFUNC("ixgbe_clear_vfta_82598"); 1044 1045 for (offset = 0; offset < hw->mac.vft_size; offset++) 1046 IXGBE_WRITE_REG(hw, IXGBE_VFTA(offset), 0); 1047 1048 for (vlanbyte = 0; vlanbyte < 4; vlanbyte++) 1049 for (offset = 0; offset < hw->mac.vft_size; offset++) 1050 IXGBE_WRITE_REG(hw, IXGBE_VFTAVIND(vlanbyte, offset), 1051 0); 1052 1053 return IXGBE_SUCCESS; 1054 } 1055 1056 /** 1057 * ixgbe_read_analog_reg8_82598 - Reads 8 bit Atlas analog register 1058 * @hw: pointer to hardware structure 1059 * @reg: analog register to read 1060 * @val: read value 1061 * 1062 * Performs read operation to Atlas analog register specified. 1063 **/ 1064 s32 ixgbe_read_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 *val) 1065 { 1066 u32 atlas_ctl; 1067 1068 DEBUGFUNC("ixgbe_read_analog_reg8_82598"); 1069 1070 IXGBE_WRITE_REG(hw, IXGBE_ATLASCTL, 1071 IXGBE_ATLASCTL_WRITE_CMD | (reg << 8)); 1072 IXGBE_WRITE_FLUSH(hw); 1073 usec_delay(10); 1074 atlas_ctl = IXGBE_READ_REG(hw, IXGBE_ATLASCTL); 1075 *val = (u8)atlas_ctl; 1076 1077 return IXGBE_SUCCESS; 1078 } 1079 1080 /** 1081 * ixgbe_write_analog_reg8_82598 - Writes 8 bit Atlas analog register 1082 * @hw: pointer to hardware structure 1083 * @reg: atlas register to write 1084 * @val: value to write 1085 * 1086 * Performs write operation to Atlas analog register specified. 1087 **/ 1088 s32 ixgbe_write_analog_reg8_82598(struct ixgbe_hw *hw, u32 reg, u8 val) 1089 { 1090 u32 atlas_ctl; 1091 1092 DEBUGFUNC("ixgbe_write_analog_reg8_82598"); 1093 1094 atlas_ctl = (reg << 8) | val; 1095 IXGBE_WRITE_REG(hw, IXGBE_ATLASCTL, atlas_ctl); 1096 IXGBE_WRITE_FLUSH(hw); 1097 usec_delay(10); 1098 1099 return IXGBE_SUCCESS; 1100 } 1101 1102 /** 1103 * ixgbe_read_i2c_phy_82598 - Reads 8 bit word over I2C interface. 1104 * @hw: pointer to hardware structure 1105 * @dev_addr: address to read from 1106 * @byte_offset: byte offset to read from dev_addr 1107 * @eeprom_data: value read 1108 * 1109 * Performs 8 byte read operation to SFP module's EEPROM over I2C interface. 1110 **/ 1111 static s32 ixgbe_read_i2c_phy_82598(struct ixgbe_hw *hw, u8 dev_addr, 1112 u8 byte_offset, u8 *eeprom_data) 1113 { 1114 s32 status = IXGBE_SUCCESS; 1115 u16 sfp_addr = 0; 1116 u16 sfp_data = 0; 1117 u16 sfp_stat = 0; 1118 u32 i; 1119 1120 DEBUGFUNC("ixgbe_read_i2c_phy_82598"); 1121 1122 if (hw->phy.type == ixgbe_phy_nl) { 1123 /* 1124 * NetLogic phy SDA/SCL registers are at addresses 0xC30A to 1125 * 0xC30D. These registers are used to talk to the SFP+ 1126 * module's EEPROM through the SDA/SCL (I2C) interface. 1127 */ 1128 sfp_addr = (dev_addr << 8) + byte_offset; 1129 sfp_addr = (sfp_addr | IXGBE_I2C_EEPROM_READ_MASK); 1130 hw->phy.ops.write_reg(hw, 1131 IXGBE_MDIO_PMA_PMD_SDA_SCL_ADDR, 1132 IXGBE_MDIO_PMA_PMD_DEV_TYPE, 1133 sfp_addr); 1134 1135 /* Poll status */ 1136 for (i = 0; i < 100; i++) { 1137 hw->phy.ops.read_reg(hw, 1138 IXGBE_MDIO_PMA_PMD_SDA_SCL_STAT, 1139 IXGBE_MDIO_PMA_PMD_DEV_TYPE, 1140 &sfp_stat); 1141 sfp_stat = sfp_stat & IXGBE_I2C_EEPROM_STATUS_MASK; 1142 if (sfp_stat != IXGBE_I2C_EEPROM_STATUS_IN_PROGRESS) 1143 break; 1144 msec_delay(10); 1145 } 1146 1147 if (sfp_stat != IXGBE_I2C_EEPROM_STATUS_PASS) { 1148 DEBUGOUT("EEPROM read did not pass.\n"); 1149 status = IXGBE_ERR_SFP_NOT_PRESENT; 1150 goto out; 1151 } 1152 1153 /* Read data */ 1154 hw->phy.ops.read_reg(hw, IXGBE_MDIO_PMA_PMD_SDA_SCL_DATA, 1155 IXGBE_MDIO_PMA_PMD_DEV_TYPE, &sfp_data); 1156 1157 *eeprom_data = (u8)(sfp_data >> 8); 1158 } else { 1159 status = IXGBE_ERR_PHY; 1160 } 1161 1162 out: 1163 return status; 1164 } 1165 1166 /** 1167 * ixgbe_read_i2c_eeprom_82598 - Reads 8 bit word over I2C interface. 1168 * @hw: pointer to hardware structure 1169 * @byte_offset: EEPROM byte offset to read 1170 * @eeprom_data: value read 1171 * 1172 * Performs 8 byte read operation to SFP module's EEPROM over I2C interface. 1173 **/ 1174 s32 ixgbe_read_i2c_eeprom_82598(struct ixgbe_hw *hw, u8 byte_offset, 1175 u8 *eeprom_data) 1176 { 1177 return ixgbe_read_i2c_phy_82598(hw, IXGBE_I2C_EEPROM_DEV_ADDR, 1178 byte_offset, eeprom_data); 1179 } 1180 1181 /** 1182 * ixgbe_read_i2c_sff8472_82598 - Reads 8 bit word over I2C interface. 1183 * @hw: pointer to hardware structure 1184 * @byte_offset: byte offset at address 0xA2 1185 * @eeprom_data: value read 1186 * 1187 * Performs 8 byte read operation to SFP module's SFF-8472 data over I2C 1188 **/ 1189 static s32 ixgbe_read_i2c_sff8472_82598(struct ixgbe_hw *hw, u8 byte_offset, 1190 u8 *sff8472_data) 1191 { 1192 return ixgbe_read_i2c_phy_82598(hw, IXGBE_I2C_EEPROM_DEV_ADDR2, 1193 byte_offset, sff8472_data); 1194 } 1195 1196 /** 1197 * ixgbe_get_supported_physical_layer_82598 - Returns physical layer type 1198 * @hw: pointer to hardware structure 1199 * 1200 * Determines physical layer capabilities of the current configuration. 1201 **/ 1202 u32 ixgbe_get_supported_physical_layer_82598(struct ixgbe_hw *hw) 1203 { 1204 u32 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN; 1205 u32 autoc = IXGBE_READ_REG(hw, IXGBE_AUTOC); 1206 u32 pma_pmd_10g = autoc & IXGBE_AUTOC_10G_PMA_PMD_MASK; 1207 u32 pma_pmd_1g = autoc & IXGBE_AUTOC_1G_PMA_PMD_MASK; 1208 u16 ext_ability = 0; 1209 1210 DEBUGFUNC("ixgbe_get_supported_physical_layer_82598"); 1211 1212 hw->phy.ops.identify(hw); 1213 1214 /* Copper PHY must be checked before AUTOC LMS to determine correct 1215 * physical layer because 10GBase-T PHYs use LMS = KX4/KX */ 1216 switch (hw->phy.type) { 1217 case ixgbe_phy_tn: 1218 case ixgbe_phy_cu_unknown: 1219 hw->phy.ops.read_reg(hw, IXGBE_MDIO_PHY_EXT_ABILITY, 1220 IXGBE_MDIO_PMA_PMD_DEV_TYPE, &ext_ability); 1221 if (ext_ability & IXGBE_MDIO_PHY_10GBASET_ABILITY) 1222 physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_T; 1223 if (ext_ability & IXGBE_MDIO_PHY_1000BASET_ABILITY) 1224 physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_T; 1225 if (ext_ability & IXGBE_MDIO_PHY_100BASETX_ABILITY) 1226 physical_layer |= IXGBE_PHYSICAL_LAYER_100BASE_TX; 1227 goto out; 1228 default: 1229 break; 1230 } 1231 1232 switch (autoc & IXGBE_AUTOC_LMS_MASK) { 1233 case IXGBE_AUTOC_LMS_1G_AN: 1234 case IXGBE_AUTOC_LMS_1G_LINK_NO_AN: 1235 if (pma_pmd_1g == IXGBE_AUTOC_1G_KX) 1236 physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_KX; 1237 else 1238 physical_layer = IXGBE_PHYSICAL_LAYER_1000BASE_BX; 1239 break; 1240 case IXGBE_AUTOC_LMS_10G_LINK_NO_AN: 1241 if (pma_pmd_10g == IXGBE_AUTOC_10G_CX4) 1242 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_CX4; 1243 else if (pma_pmd_10g == IXGBE_AUTOC_10G_KX4) 1244 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_KX4; 1245 else /* XAUI */ 1246 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN; 1247 break; 1248 case IXGBE_AUTOC_LMS_KX4_AN: 1249 case IXGBE_AUTOC_LMS_KX4_AN_1G_AN: 1250 if (autoc & IXGBE_AUTOC_KX_SUPP) 1251 physical_layer |= IXGBE_PHYSICAL_LAYER_1000BASE_KX; 1252 if (autoc & IXGBE_AUTOC_KX4_SUPP) 1253 physical_layer |= IXGBE_PHYSICAL_LAYER_10GBASE_KX4; 1254 break; 1255 default: 1256 break; 1257 } 1258 1259 if (hw->phy.type == ixgbe_phy_nl) { 1260 hw->phy.ops.identify_sfp(hw); 1261 1262 switch (hw->phy.sfp_type) { 1263 case ixgbe_sfp_type_da_cu: 1264 physical_layer = IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU; 1265 break; 1266 case ixgbe_sfp_type_sr: 1267 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_SR; 1268 break; 1269 case ixgbe_sfp_type_lr: 1270 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_LR; 1271 break; 1272 default: 1273 physical_layer = IXGBE_PHYSICAL_LAYER_UNKNOWN; 1274 break; 1275 } 1276 } 1277 1278 switch (hw->device_id) { 1279 case IXGBE_DEV_ID_82598_DA_DUAL_PORT: 1280 physical_layer = IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU; 1281 break; 1282 case IXGBE_DEV_ID_82598AF_DUAL_PORT: 1283 case IXGBE_DEV_ID_82598AF_SINGLE_PORT: 1284 case IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM: 1285 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_SR; 1286 break; 1287 case IXGBE_DEV_ID_82598EB_XF_LR: 1288 physical_layer = IXGBE_PHYSICAL_LAYER_10GBASE_LR; 1289 break; 1290 default: 1291 break; 1292 } 1293 1294 out: 1295 return physical_layer; 1296 } 1297 1298 /** 1299 * ixgbe_set_lan_id_multi_port_pcie_82598 - Set LAN id for PCIe multiple 1300 * port devices. 1301 * @hw: pointer to the HW structure 1302 * 1303 * Calls common function and corrects issue with some single port devices 1304 * that enable LAN1 but not LAN0. 1305 **/ 1306 void ixgbe_set_lan_id_multi_port_pcie_82598(struct ixgbe_hw *hw) 1307 { 1308 struct ixgbe_bus_info *bus = &hw->bus; 1309 u16 pci_gen = 0; 1310 u16 pci_ctrl2 = 0; 1311 1312 DEBUGFUNC("ixgbe_set_lan_id_multi_port_pcie_82598"); 1313 1314 ixgbe_set_lan_id_multi_port_pcie(hw); 1315 1316 /* check if LAN0 is disabled */ 1317 hw->eeprom.ops.read(hw, IXGBE_PCIE_GENERAL_PTR, &pci_gen); 1318 if ((pci_gen != 0) && (pci_gen != 0xFFFF)) { 1319 1320 hw->eeprom.ops.read(hw, pci_gen + IXGBE_PCIE_CTRL2, &pci_ctrl2); 1321 1322 /* if LAN0 is completely disabled force function to 0 */ 1323 if ((pci_ctrl2 & IXGBE_PCIE_CTRL2_LAN_DISABLE) && 1324 !(pci_ctrl2 & IXGBE_PCIE_CTRL2_DISABLE_SELECT) && 1325 !(pci_ctrl2 & IXGBE_PCIE_CTRL2_DUMMY_ENABLE)) { 1326 1327 bus->func = 0; 1328 } 1329 } 1330 } 1331 1332 /** 1333 * ixgbe_enable_relaxed_ordering_82598 - enable relaxed ordering 1334 * @hw: pointer to hardware structure 1335 * 1336 **/ 1337 void ixgbe_enable_relaxed_ordering_82598(struct ixgbe_hw *hw) 1338 { 1339 u32 regval; 1340 u32 i; 1341 1342 DEBUGFUNC("ixgbe_enable_relaxed_ordering_82598"); 1343 1344 /* Enable relaxed ordering */ 1345 for (i = 0; ((i < hw->mac.max_tx_queues) && 1346 (i < IXGBE_DCA_MAX_QUEUES_82598)); i++) { 1347 regval = IXGBE_READ_REG(hw, IXGBE_DCA_TXCTRL(i)); 1348 regval |= IXGBE_DCA_TXCTRL_DESC_WRO_EN; 1349 IXGBE_WRITE_REG(hw, IXGBE_DCA_TXCTRL(i), regval); 1350 } 1351 1352 for (i = 0; ((i < hw->mac.max_rx_queues) && 1353 (i < IXGBE_DCA_MAX_QUEUES_82598)); i++) { 1354 regval = IXGBE_READ_REG(hw, IXGBE_DCA_RXCTRL(i)); 1355 regval |= IXGBE_DCA_RXCTRL_DATA_WRO_EN | 1356 IXGBE_DCA_RXCTRL_HEAD_WRO_EN; 1357 IXGBE_WRITE_REG(hw, IXGBE_DCA_RXCTRL(i), regval); 1358 } 1359 1360 } 1361 1362 /** 1363 * ixgbe_set_rxpba_82598 - Initialize RX packet buffer 1364 * @hw: pointer to hardware structure 1365 * @num_pb: number of packet buffers to allocate 1366 * @headroom: reserve n KB of headroom 1367 * @strategy: packet buffer allocation strategy 1368 **/ 1369 static void ixgbe_set_rxpba_82598(struct ixgbe_hw *hw, int num_pb, 1370 u32 headroom, int strategy) 1371 { 1372 u32 rxpktsize = IXGBE_RXPBSIZE_64KB; 1373 u8 i = 0; 1374 UNREFERENCED_1PARAMETER(headroom); 1375 1376 if (!num_pb) 1377 return; 1378 1379 /* Setup Rx packet buffer sizes */ 1380 switch (strategy) { 1381 case PBA_STRATEGY_WEIGHTED: 1382 /* Setup the first four at 80KB */ 1383 rxpktsize = IXGBE_RXPBSIZE_80KB; 1384 for (; i < 4; i++) 1385 IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize); 1386 /* Setup the last four at 48KB...don't re-init i */ 1387 rxpktsize = IXGBE_RXPBSIZE_48KB; 1388 /* Fall Through */ 1389 case PBA_STRATEGY_EQUAL: 1390 default: 1391 /* Divide the remaining Rx packet buffer evenly among the TCs */ 1392 for (; i < IXGBE_MAX_PACKET_BUFFERS; i++) 1393 IXGBE_WRITE_REG(hw, IXGBE_RXPBSIZE(i), rxpktsize); 1394 break; 1395 } 1396 1397 /* Setup Tx packet buffer sizes */ 1398 for (i = 0; i < IXGBE_MAX_PACKET_BUFFERS; i++) 1399 IXGBE_WRITE_REG(hw, IXGBE_TXPBSIZE(i), IXGBE_TXPBSIZE_40KB); 1400 1401 return; 1402 } 1403