1 /* $FreeBSD$ */ 2 /*- 3 * Copyright (c) 1997-2009 by Matthew Jacob 4 * All rights reserved. 5 * 6 * Redistribution and use in source and binary forms, with or without 7 * modification, are permitted provided that the following conditions 8 * are met: 9 * 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 16 * THIS SOFTWARE IS PROVIDED BY AUTHOR AND CONTRIBUTORS ``AS IS'' AND 17 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 18 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 19 * ARE DISCLAIMED. IN NO EVENT SHALL AUTHOR OR CONTRIBUTORS BE LIABLE 20 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 21 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 22 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 23 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 24 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 25 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 26 * SUCH DAMAGE. 27 * 28 */ 29 /* 30 * Machine Independent (well, as best as possible) register 31 * definitions for Qlogic ISP SCSI adapters. 32 */ 33 #ifndef _ISPREG_H 34 #define _ISPREG_H 35 36 /* 37 * Hardware definitions for the Qlogic ISP registers. 38 */ 39 40 /* 41 * This defines types of access to various registers. 42 * 43 * R: Read Only 44 * W: Write Only 45 * RW: Read/Write 46 * 47 * R*, W*, RW*: Read Only, Write Only, Read/Write, but only 48 * if RISC processor in ISP is paused. 49 */ 50 51 /* 52 * Offsets for various register blocks. 53 * 54 * Sad but true, different architectures have different offsets. 55 * 56 * Don't be alarmed if none of this makes sense. The original register 57 * layout set some defines in a certain pattern. Everything else has been 58 * grafted on since. For example, the ISP1080 manual will state that DMA 59 * registers start at 0x80 from the base of the register address space. 60 * That's true, but for our purposes, we define DMA_REGS_OFF for the 1080 61 * to start at offset 0x60 because the DMA registers are all defined to 62 * be DMA_BLOCK+0x20 and so on. Clear? 63 */ 64 65 #define BIU_REGS_OFF 0x00 66 67 #define PCI_MBOX_REGS_OFF 0x70 68 #define PCI_MBOX_REGS2100_OFF 0x10 69 #define PCI_MBOX_REGS2300_OFF 0x40 70 #define PCI_MBOX_REGS2400_OFF 0x80 71 #define SBUS_MBOX_REGS_OFF 0x80 72 73 #define PCI_SXP_REGS_OFF 0x80 74 #define SBUS_SXP_REGS_OFF 0x200 75 76 #define PCI_RISC_REGS_OFF 0x80 77 #define SBUS_RISC_REGS_OFF 0x400 78 79 /* Bless me! Chip designers have putzed it again! */ 80 #define ISP1080_DMA_REGS_OFF 0x60 81 #define DMA_REGS_OFF 0x00 /* same as BIU block */ 82 83 #define SBUS_REGSIZE 0x450 84 #define PCI_REGSIZE 0x100 85 86 /* 87 * NB: The *_BLOCK definitions have no specific hardware meaning. 88 * They serve simply to note to the MD layer which block of 89 * registers offsets are being accessed. 90 */ 91 #define _NREG_BLKS 5 92 #define _BLK_REG_SHFT 13 93 #define _BLK_REG_MASK (7 << _BLK_REG_SHFT) 94 #define BIU_BLOCK (0 << _BLK_REG_SHFT) 95 #define MBOX_BLOCK (1 << _BLK_REG_SHFT) 96 #define SXP_BLOCK (2 << _BLK_REG_SHFT) 97 #define RISC_BLOCK (3 << _BLK_REG_SHFT) 98 #define DMA_BLOCK (4 << _BLK_REG_SHFT) 99 100 /* 101 * Bus Interface Block Register Offsets 102 */ 103 104 #define BIU_ID_LO (BIU_BLOCK+0x0) /* R : Bus ID, Low */ 105 #define BIU2100_FLASH_ADDR (BIU_BLOCK+0x0) 106 #define BIU_ID_HI (BIU_BLOCK+0x2) /* R : Bus ID, High */ 107 #define BIU2100_FLASH_DATA (BIU_BLOCK+0x2) 108 #define BIU_CONF0 (BIU_BLOCK+0x4) /* R : Bus Configuration #0 */ 109 #define BIU_CONF1 (BIU_BLOCK+0x6) /* R : Bus Configuration #1 */ 110 #define BIU2100_CSR (BIU_BLOCK+0x6) 111 #define BIU_ICR (BIU_BLOCK+0x8) /* RW : Bus Interface Ctrl */ 112 #define BIU_ISR (BIU_BLOCK+0xA) /* R : Bus Interface Status */ 113 #define BIU_SEMA (BIU_BLOCK+0xC) /* RW : Bus Semaphore */ 114 #define BIU_NVRAM (BIU_BLOCK+0xE) /* RW : Bus NVRAM */ 115 /* 116 * These are specific to the 2300. 117 */ 118 #define BIU_REQINP (BIU_BLOCK+0x10) /* Request Queue In */ 119 #define BIU_REQOUTP (BIU_BLOCK+0x12) /* Request Queue Out */ 120 #define BIU_RSPINP (BIU_BLOCK+0x14) /* Response Queue In */ 121 #define BIU_RSPOUTP (BIU_BLOCK+0x16) /* Response Queue Out */ 122 123 #define BIU_R2HSTSLO (BIU_BLOCK+0x18) 124 #define BIU_R2HSTSHI (BIU_BLOCK+0x1A) 125 126 #define BIU_R2HST_INTR (1 << 15) /* RISC to Host Interrupt */ 127 #define BIU_R2HST_PAUSED (1 << 8) /* RISC paused */ 128 #define BIU_R2HST_ISTAT_MASK 0xff /* intr information && status */ 129 #define ISPR2HST_ROM_MBX_OK 0x1 /* ROM mailbox cmd done ok */ 130 #define ISPR2HST_ROM_MBX_FAIL 0x2 /* ROM mailbox cmd done fail */ 131 #define ISPR2HST_MBX_OK 0x10 /* mailbox cmd done ok */ 132 #define ISPR2HST_MBX_FAIL 0x11 /* mailbox cmd done fail */ 133 #define ISPR2HST_ASYNC_EVENT 0x12 /* Async Event */ 134 #define ISPR2HST_RSPQ_UPDATE 0x13 /* Response Queue Update */ 135 #define ISPR2HST_RSPQ_UPDATE2 0x14 /* Response Queue Update */ 136 #define ISPR2HST_RIO_16 0x15 /* RIO 1-16 */ 137 #define ISPR2HST_FPOST 0x16 /* Low 16 bits fast post */ 138 #define ISPR2HST_FPOST_CTIO 0x17 /* Low 16 bits fast post ctio */ 139 #define ISPR2HST_ATIO_UPDATE 0x1C /* ATIO Queue Update */ 140 #define ISPR2HST_ATIO_RSPQ_UPDATE 0x1D /* ATIO & Request Update */ 141 #define ISPR2HST_ATIO_UPDATE2 0x1E /* ATIO Queue Update */ 142 143 /* fifo command stuff- mostly for SPI */ 144 #define DFIFO_COMMAND (BIU_BLOCK+0x60) /* RW : Command FIFO Port */ 145 #define RDMA2100_CONTROL DFIFO_COMMAND 146 #define DFIFO_DATA (BIU_BLOCK+0x62) /* RW : Data FIFO Port */ 147 148 /* 149 * Putzed DMA register layouts. 150 */ 151 #define CDMA_CONF (DMA_BLOCK+0x20) /* RW*: DMA Configuration */ 152 #define CDMA2100_CONTROL CDMA_CONF 153 #define CDMA_CONTROL (DMA_BLOCK+0x22) /* RW*: DMA Control */ 154 #define CDMA_STATUS (DMA_BLOCK+0x24) /* R : DMA Status */ 155 #define CDMA_FIFO_STS (DMA_BLOCK+0x26) /* R : DMA FIFO Status */ 156 #define CDMA_COUNT (DMA_BLOCK+0x28) /* RW*: DMA Transfer Count */ 157 #define CDMA_ADDR0 (DMA_BLOCK+0x2C) /* RW*: DMA Address, Word 0 */ 158 #define CDMA_ADDR1 (DMA_BLOCK+0x2E) /* RW*: DMA Address, Word 1 */ 159 #define CDMA_ADDR2 (DMA_BLOCK+0x30) /* RW*: DMA Address, Word 2 */ 160 #define CDMA_ADDR3 (DMA_BLOCK+0x32) /* RW*: DMA Address, Word 3 */ 161 162 #define DDMA_CONF (DMA_BLOCK+0x40) /* RW*: DMA Configuration */ 163 #define TDMA2100_CONTROL DDMA_CONF 164 #define DDMA_CONTROL (DMA_BLOCK+0x42) /* RW*: DMA Control */ 165 #define DDMA_STATUS (DMA_BLOCK+0x44) /* R : DMA Status */ 166 #define DDMA_FIFO_STS (DMA_BLOCK+0x46) /* R : DMA FIFO Status */ 167 #define DDMA_COUNT_LO (DMA_BLOCK+0x48) /* RW*: DMA Xfer Count, Low */ 168 #define DDMA_COUNT_HI (DMA_BLOCK+0x4A) /* RW*: DMA Xfer Count, High */ 169 #define DDMA_ADDR0 (DMA_BLOCK+0x4C) /* RW*: DMA Address, Word 0 */ 170 #define DDMA_ADDR1 (DMA_BLOCK+0x4E) /* RW*: DMA Address, Word 1 */ 171 /* these are for the 1040A cards */ 172 #define DDMA_ADDR2 (DMA_BLOCK+0x50) /* RW*: DMA Address, Word 2 */ 173 #define DDMA_ADDR3 (DMA_BLOCK+0x52) /* RW*: DMA Address, Word 3 */ 174 175 176 /* 177 * Bus Interface Block Register Definitions 178 */ 179 /* BUS CONFIGURATION REGISTER #0 */ 180 #define BIU_CONF0_HW_MASK 0x000F /* Hardware revision mask */ 181 /* BUS CONFIGURATION REGISTER #1 */ 182 183 #define BIU_SBUS_CONF1_PARITY 0x0100 /* Enable parity checking */ 184 #define BIU_SBUS_CONF1_FCODE_MASK 0x00F0 /* Fcode cycle mask */ 185 186 #define BIU_PCI_CONF1_FIFO_128 0x0040 /* 128 bytes FIFO threshold */ 187 #define BIU_PCI_CONF1_FIFO_64 0x0030 /* 64 bytes FIFO threshold */ 188 #define BIU_PCI_CONF1_FIFO_32 0x0020 /* 32 bytes FIFO threshold */ 189 #define BIU_PCI_CONF1_FIFO_16 0x0010 /* 16 bytes FIFO threshold */ 190 #define BIU_BURST_ENABLE 0x0004 /* Global enable Bus bursts */ 191 #define BIU_SBUS_CONF1_FIFO_64 0x0003 /* 64 bytes FIFO threshold */ 192 #define BIU_SBUS_CONF1_FIFO_32 0x0002 /* 32 bytes FIFO threshold */ 193 #define BIU_SBUS_CONF1_FIFO_16 0x0001 /* 16 bytes FIFO threshold */ 194 #define BIU_SBUS_CONF1_FIFO_8 0x0000 /* 8 bytes FIFO threshold */ 195 #define BIU_SBUS_CONF1_BURST8 0x0008 /* Enable 8-byte bursts */ 196 #define BIU_PCI_CONF1_SXP 0x0008 /* SXP register select */ 197 198 #define BIU_PCI1080_CONF1_SXP0 0x0100 /* SXP bank #1 select */ 199 #define BIU_PCI1080_CONF1_SXP1 0x0200 /* SXP bank #2 select */ 200 #define BIU_PCI1080_CONF1_DMA 0x0300 /* DMA bank select */ 201 202 /* ISP2100 Bus Control/Status Register */ 203 204 #define BIU2100_ICSR_REGBSEL 0x30 /* RW: register bank select */ 205 #define BIU2100_RISC_REGS (0 << 4) /* RISC Regs */ 206 #define BIU2100_FB_REGS (1 << 4) /* FrameBuffer Regs */ 207 #define BIU2100_FPM0_REGS (2 << 4) /* FPM 0 Regs */ 208 #define BIU2100_FPM1_REGS (3 << 4) /* FPM 1 Regs */ 209 #define BIU2100_NVRAM_OFFSET (1 << 14) 210 #define BIU2100_FLASH_UPPER_64K 0x04 /* RW: Upper 64K Bank Select */ 211 #define BIU2100_FLASH_ENABLE 0x02 /* RW: Enable Flash RAM */ 212 #define BIU2100_SOFT_RESET 0x01 213 /* SOFT RESET FOR ISP2100 is same bit, but in this register, not ICR */ 214 215 216 /* BUS CONTROL REGISTER */ 217 #define BIU_ICR_ENABLE_DMA_INT 0x0020 /* Enable DMA interrupts */ 218 #define BIU_ICR_ENABLE_CDMA_INT 0x0010 /* Enable CDMA interrupts */ 219 #define BIU_ICR_ENABLE_SXP_INT 0x0008 /* Enable SXP interrupts */ 220 #define BIU_ICR_ENABLE_RISC_INT 0x0004 /* Enable Risc interrupts */ 221 #define BIU_ICR_ENABLE_ALL_INTS 0x0002 /* Global enable all inter */ 222 #define BIU_ICR_SOFT_RESET 0x0001 /* Soft Reset of ISP */ 223 224 #define BIU_IMASK (BIU_ICR_ENABLE_RISC_INT|BIU_ICR_ENABLE_ALL_INTS) 225 226 #define BIU2100_ICR_ENABLE_ALL_INTS 0x8000 227 #define BIU2100_ICR_ENA_FPM_INT 0x0020 228 #define BIU2100_ICR_ENA_FB_INT 0x0010 229 #define BIU2100_ICR_ENA_RISC_INT 0x0008 230 #define BIU2100_ICR_ENA_CDMA_INT 0x0004 231 #define BIU2100_ICR_ENABLE_RXDMA_INT 0x0002 232 #define BIU2100_ICR_ENABLE_TXDMA_INT 0x0001 233 #define BIU2100_ICR_DISABLE_ALL_INTS 0x0000 234 235 #define BIU2100_IMASK (BIU2100_ICR_ENA_RISC_INT|BIU2100_ICR_ENABLE_ALL_INTS) 236 237 /* BUS STATUS REGISTER */ 238 #define BIU_ISR_DMA_INT 0x0020 /* DMA interrupt pending */ 239 #define BIU_ISR_CDMA_INT 0x0010 /* CDMA interrupt pending */ 240 #define BIU_ISR_SXP_INT 0x0008 /* SXP interrupt pending */ 241 #define BIU_ISR_RISC_INT 0x0004 /* Risc interrupt pending */ 242 #define BIU_ISR_IPEND 0x0002 /* Global interrupt pending */ 243 244 #define BIU2100_ISR_INT_PENDING 0x8000 /* Global interrupt pending */ 245 #define BIU2100_ISR_FPM_INT 0x0020 /* FPM interrupt pending */ 246 #define BIU2100_ISR_FB_INT 0x0010 /* FB interrupt pending */ 247 #define BIU2100_ISR_RISC_INT 0x0008 /* Risc interrupt pending */ 248 #define BIU2100_ISR_CDMA_INT 0x0004 /* CDMA interrupt pending */ 249 #define BIU2100_ISR_RXDMA_INT_PENDING 0x0002 /* Global interrupt pending */ 250 #define BIU2100_ISR_TXDMA_INT_PENDING 0x0001 /* Global interrupt pending */ 251 252 #define INT_PENDING_MASK(isp) \ 253 (IS_FC(isp)? (IS_24XX(isp)? BIU2400_ISR_RISC_INT : BIU2100_ISR_RISC_INT) : \ 254 (BIU_ISR_RISC_INT)) 255 256 /* BUS SEMAPHORE REGISTER */ 257 #define BIU_SEMA_STATUS 0x0002 /* Semaphore Status Bit */ 258 #define BIU_SEMA_LOCK 0x0001 /* Semaphore Lock Bit */ 259 260 /* NVRAM SEMAPHORE REGISTER */ 261 #define BIU_NVRAM_CLOCK 0x0001 262 #define BIU_NVRAM_SELECT 0x0002 263 #define BIU_NVRAM_DATAOUT 0x0004 264 #define BIU_NVRAM_DATAIN 0x0008 265 #define BIU_NVRAM_BUSY 0x0080 /* 2322/24xx only */ 266 #define ISP_NVRAM_READ 6 267 268 /* COMNMAND && DATA DMA CONFIGURATION REGISTER */ 269 #define DMA_ENABLE_SXP_DMA 0x0008 /* Enable SXP to DMA Data */ 270 #define DMA_ENABLE_INTS 0x0004 /* Enable interrupts to RISC */ 271 #define DMA_ENABLE_BURST 0x0002 /* Enable Bus burst trans */ 272 #define DMA_DMA_DIRECTION 0x0001 /* 273 * Set DMA direction: 274 * 0 - DMA FIFO to host 275 * 1 - Host to DMA FIFO 276 */ 277 278 /* COMMAND && DATA DMA CONTROL REGISTER */ 279 #define DMA_CNTRL_SUSPEND_CHAN 0x0010 /* Suspend DMA transfer */ 280 #define DMA_CNTRL_CLEAR_CHAN 0x0008 /* 281 * Clear FIFO and DMA Channel, 282 * reset DMA registers 283 */ 284 #define DMA_CNTRL_CLEAR_FIFO 0x0004 /* Clear DMA FIFO */ 285 #define DMA_CNTRL_RESET_INT 0x0002 /* Clear DMA interrupt */ 286 #define DMA_CNTRL_STROBE 0x0001 /* Start DMA transfer */ 287 288 /* 289 * Variants of same for 2100 290 */ 291 #define DMA_CNTRL2100_CLEAR_CHAN 0x0004 292 #define DMA_CNTRL2100_RESET_INT 0x0002 293 294 295 296 /* DMA STATUS REGISTER */ 297 #define DMA_SBUS_STATUS_PIPE_MASK 0x00C0 /* DMA Pipeline status mask */ 298 #define DMA_SBUS_STATUS_CHAN_MASK 0x0030 /* Channel status mask */ 299 #define DMA_SBUS_STATUS_BUS_PARITY 0x0008 /* Parity Error on bus */ 300 #define DMA_SBUS_STATUS_BUS_ERR 0x0004 /* Error Detected on bus */ 301 #define DMA_SBUS_STATUS_TERM_COUNT 0x0002 /* DMA Transfer Completed */ 302 #define DMA_SBUS_STATUS_INTERRUPT 0x0001 /* Enable DMA channel inter */ 303 304 #define DMA_PCI_STATUS_INTERRUPT 0x8000 /* Enable DMA channel inter */ 305 #define DMA_PCI_STATUS_RETRY_STAT 0x4000 /* Retry status */ 306 #define DMA_PCI_STATUS_CHAN_MASK 0x3000 /* Channel status mask */ 307 #define DMA_PCI_STATUS_FIFO_OVR 0x0100 /* DMA FIFO overrun cond */ 308 #define DMA_PCI_STATUS_FIFO_UDR 0x0080 /* DMA FIFO underrun cond */ 309 #define DMA_PCI_STATUS_BUS_ERR 0x0040 /* Error Detected on bus */ 310 #define DMA_PCI_STATUS_BUS_PARITY 0x0020 /* Parity Error on bus */ 311 #define DMA_PCI_STATUS_CLR_PEND 0x0010 /* DMA clear pending */ 312 #define DMA_PCI_STATUS_TERM_COUNT 0x0008 /* DMA Transfer Completed */ 313 #define DMA_PCI_STATUS_DMA_SUSP 0x0004 /* DMA suspended */ 314 #define DMA_PCI_STATUS_PIPE_MASK 0x0003 /* DMA Pipeline status mask */ 315 316 /* DMA Status Register, pipeline status bits */ 317 #define DMA_SBUS_PIPE_FULL 0x00C0 /* Both pipeline stages full */ 318 #define DMA_SBUS_PIPE_OVERRUN 0x0080 /* Pipeline overrun */ 319 #define DMA_SBUS_PIPE_STAGE1 0x0040 /* 320 * Pipeline stage 1 Loaded, 321 * stage 2 empty 322 */ 323 #define DMA_PCI_PIPE_FULL 0x0003 /* Both pipeline stages full */ 324 #define DMA_PCI_PIPE_OVERRUN 0x0002 /* Pipeline overrun */ 325 #define DMA_PCI_PIPE_STAGE1 0x0001 /* 326 * Pipeline stage 1 Loaded, 327 * stage 2 empty 328 */ 329 #define DMA_PIPE_EMPTY 0x0000 /* All pipeline stages empty */ 330 331 /* DMA Status Register, channel status bits */ 332 #define DMA_SBUS_CHAN_SUSPEND 0x0030 /* Channel error or suspended */ 333 #define DMA_SBUS_CHAN_TRANSFER 0x0020 /* Chan transfer in progress */ 334 #define DMA_SBUS_CHAN_ACTIVE 0x0010 /* Chan trans to host active */ 335 #define DMA_PCI_CHAN_TRANSFER 0x3000 /* Chan transfer in progress */ 336 #define DMA_PCI_CHAN_SUSPEND 0x2000 /* Channel error or suspended */ 337 #define DMA_PCI_CHAN_ACTIVE 0x1000 /* Chan trans to host active */ 338 #define ISP_DMA_CHAN_IDLE 0x0000 /* Chan idle (normal comp) */ 339 340 341 /* DMA FIFO STATUS REGISTER */ 342 #define DMA_FIFO_STATUS_OVERRUN 0x0200 /* FIFO Overrun Condition */ 343 #define DMA_FIFO_STATUS_UNDERRUN 0x0100 /* FIFO Underrun Condition */ 344 #define DMA_FIFO_SBUS_COUNT_MASK 0x007F /* FIFO Byte count mask */ 345 #define DMA_FIFO_PCI_COUNT_MASK 0x00FF /* FIFO Byte count mask */ 346 347 /* 348 * 2400 Interface Offsets and Register Definitions 349 * 350 * The 2400 looks quite different in terms of registers from other QLogic cards. 351 * It is getting to be a genuine pain and challenge to keep the same model 352 * for all. 353 */ 354 #define BIU2400_FLASH_ADDR (BIU_BLOCK+0x00) 355 #define BIU2400_FLASH_DATA (BIU_BLOCK+0x04) 356 #define BIU2400_CSR (BIU_BLOCK+0x08) 357 #define BIU2400_ICR (BIU_BLOCK+0x0C) 358 #define BIU2400_ISR (BIU_BLOCK+0x10) 359 360 #define BIU2400_REQINP (BIU_BLOCK+0x1C) /* Request Queue In */ 361 #define BIU2400_REQOUTP (BIU_BLOCK+0x20) /* Request Queue Out */ 362 #define BIU2400_RSPINP (BIU_BLOCK+0x24) /* Response Queue In */ 363 #define BIU2400_RSPOUTP (BIU_BLOCK+0x28) /* Response Queue Out */ 364 365 #define BIU2400_PRI_REQINP (BIU_BLOCK+0x2C) /* Priority Request Q In */ 366 #define BIU2400_PRI_REQOUTP (BIU_BLOCK+0x30) /* Priority Request Q Out */ 367 368 #define BIU2400_ATIO_RSPINP (BIU_BLOCK+0x3C) /* ATIO Queue In */ 369 #define BIU2400_ATIO_RSPOUTP (BIU_BLOCK+0x40) /* ATIO Queue Out */ 370 371 #define BIU2400_R2HSTSLO (BIU_BLOCK+0x44) 372 #define BIU2400_R2HSTSHI (BIU_BLOCK+0x46) 373 374 #define BIU2400_HCCR (BIU_BLOCK+0x48) 375 #define BIU2400_GPIOD (BIU_BLOCK+0x4C) 376 #define BIU2400_GPIOE (BIU_BLOCK+0x50) 377 #define BIU2400_HSEMA (BIU_BLOCK+0x58) 378 379 /* BIU2400_FLASH_ADDR definitions */ 380 #define BIU2400_FLASH_DFLAG (1 << 30) 381 382 /* BIU2400_CSR definitions */ 383 #define BIU2400_NVERR (1 << 18) 384 #define BIU2400_DMA_ACTIVE (1 << 17) /* RO */ 385 #define BIU2400_DMA_STOP (1 << 16) 386 #define BIU2400_FUNCTION (1 << 15) /* RO */ 387 #define BIU2400_PCIX_MODE(x) (((x) >> 8) & 0xf) /* RO */ 388 #define BIU2400_CSR_64BIT (1 << 2) /* RO */ 389 #define BIU2400_FLASH_ENABLE (1 << 1) 390 #define BIU2400_SOFT_RESET (1 << 0) 391 392 /* BIU2400_ICR definitions */ 393 #define BIU2400_ICR_ENA_RISC_INT 0x8 394 #define BIU2400_IMASK (BIU2400_ICR_ENA_RISC_INT) 395 396 /* BIU2400_ISR definitions */ 397 #define BIU2400_ISR_RISC_INT 0x8 398 399 /* BIU2400_HCCR definitions */ 400 401 #define HCCR_2400_CMD_NOP 0x00000000 402 #define HCCR_2400_CMD_RESET 0x10000000 403 #define HCCR_2400_CMD_CLEAR_RESET 0x20000000 404 #define HCCR_2400_CMD_PAUSE 0x30000000 405 #define HCCR_2400_CMD_RELEASE 0x40000000 406 #define HCCR_2400_CMD_SET_HOST_INT 0x50000000 407 #define HCCR_2400_CMD_CLEAR_HOST_INT 0x60000000 408 #define HCCR_2400_CMD_CLEAR_RISC_INT 0xA0000000 409 410 #define HCCR_2400_RISC_ERR(x) (((x) >> 12) & 0x7) /* RO */ 411 #define HCCR_2400_RISC2HOST_INT (1 << 6) /* RO */ 412 #define HCCR_2400_RISC_RESET (1 << 5) /* RO */ 413 414 415 /* 416 * Mailbox Block Register Offsets 417 */ 418 419 #define INMAILBOX0 (MBOX_BLOCK+0x0) 420 #define INMAILBOX1 (MBOX_BLOCK+0x2) 421 #define INMAILBOX2 (MBOX_BLOCK+0x4) 422 #define INMAILBOX3 (MBOX_BLOCK+0x6) 423 #define INMAILBOX4 (MBOX_BLOCK+0x8) 424 #define INMAILBOX5 (MBOX_BLOCK+0xA) 425 #define INMAILBOX6 (MBOX_BLOCK+0xC) 426 #define INMAILBOX7 (MBOX_BLOCK+0xE) 427 428 #define OUTMAILBOX0 (MBOX_BLOCK+0x0) 429 #define OUTMAILBOX1 (MBOX_BLOCK+0x2) 430 #define OUTMAILBOX2 (MBOX_BLOCK+0x4) 431 #define OUTMAILBOX3 (MBOX_BLOCK+0x6) 432 #define OUTMAILBOX4 (MBOX_BLOCK+0x8) 433 #define OUTMAILBOX5 (MBOX_BLOCK+0xA) 434 #define OUTMAILBOX6 (MBOX_BLOCK+0xC) 435 #define OUTMAILBOX7 (MBOX_BLOCK+0xE) 436 437 /* 438 * Strictly speaking, it's 439 * SCSI && 2100 : 8 MBOX registers 440 * 2200: 24 MBOX registers 441 * 2300/2400: 32 MBOX registers 442 */ 443 #define MBOX_OFF(n) (MBOX_BLOCK + ((n) << 1)) 444 #define ISP_NMBOX(isp) ((IS_24XX(isp) || IS_23XX(isp))? 32 : (IS_2200(isp) ? 24 : 8)) 445 #define ISP_NMBOX_BMASK(isp) \ 446 ((IS_24XX(isp) || IS_23XX(isp))? 0xffffffff : (IS_2200(isp)? 0x00ffffff : 0xff)) 447 #define MAX_MAILBOX 32 448 /* if timeout == 0, then default timeout is picked */ 449 #define MBCMD_DEFAULT_TIMEOUT 100000 /* 100 ms */ 450 typedef struct { 451 uint16_t param[MAX_MAILBOX]; 452 uint32_t ibits; /* bits to add for register copyin */ 453 uint32_t obits; /* bits to add for register copyout */ 454 uint32_t ibitm; /* bits to mask for register copyin */ 455 uint32_t obitm; /* bits to mask for register copyout */ 456 uint32_t logval; /* Bitmask of status codes to log */ 457 uint32_t timeout; 458 uint32_t lineno; 459 const char *func; 460 } mbreg_t; 461 #define MBSINIT(mbxp, code, loglev, timo) \ 462 ISP_MEMZERO((mbxp), sizeof (mbreg_t)); \ 463 (mbxp)->ibitm = ~0; \ 464 (mbxp)->obitm = ~0; \ 465 (mbxp)->param[0] = code; \ 466 (mbxp)->lineno = __LINE__; \ 467 (mbxp)->func = __func__; \ 468 (mbxp)->logval = loglev; \ 469 (mbxp)->timeout = timo 470 471 472 /* 473 * Fibre Protocol Module and Frame Buffer Register Offsets/Definitions (2X00). 474 * NB: The RISC processor must be paused and the appropriate register 475 * bank selected via BIU2100_CSR bits. 476 */ 477 478 #define FPM_DIAG_CONFIG (BIU_BLOCK + 0x96) 479 #define FPM_SOFT_RESET 0x0100 480 481 #define FBM_CMD (BIU_BLOCK + 0xB8) 482 #define FBMCMD_FIFO_RESET_ALL 0xA000 483 484 485 /* 486 * SXP Block Register Offsets 487 */ 488 #define SXP_PART_ID (SXP_BLOCK+0x0) /* R : Part ID Code */ 489 #define SXP_CONFIG1 (SXP_BLOCK+0x2) /* RW*: Configuration Reg #1 */ 490 #define SXP_CONFIG2 (SXP_BLOCK+0x4) /* RW*: Configuration Reg #2 */ 491 #define SXP_CONFIG3 (SXP_BLOCK+0x6) /* RW*: Configuration Reg #2 */ 492 #define SXP_INSTRUCTION (SXP_BLOCK+0xC) /* RW*: Instruction Pointer */ 493 #define SXP_RETURN_ADDR (SXP_BLOCK+0x10) /* RW*: Return Address */ 494 #define SXP_COMMAND (SXP_BLOCK+0x14) /* RW*: Command */ 495 #define SXP_INTERRUPT (SXP_BLOCK+0x18) /* R : Interrupt */ 496 #define SXP_SEQUENCE (SXP_BLOCK+0x1C) /* RW*: Sequence */ 497 #define SXP_GROSS_ERR (SXP_BLOCK+0x1E) /* R : Gross Error */ 498 #define SXP_EXCEPTION (SXP_BLOCK+0x20) /* RW*: Exception Enable */ 499 #define SXP_OVERRIDE (SXP_BLOCK+0x24) /* RW*: Override */ 500 #define SXP_LIT_BASE (SXP_BLOCK+0x28) /* RW*: Literal Base */ 501 #define SXP_USER_FLAGS (SXP_BLOCK+0x2C) /* RW*: User Flags */ 502 #define SXP_USER_EXCEPT (SXP_BLOCK+0x30) /* RW*: User Exception */ 503 #define SXP_BREAKPOINT (SXP_BLOCK+0x34) /* RW*: Breakpoint */ 504 #define SXP_SCSI_ID (SXP_BLOCK+0x40) /* RW*: SCSI ID */ 505 #define SXP_DEV_CONFIG1 (SXP_BLOCK+0x42) /* RW*: Device Config Reg #1 */ 506 #define SXP_DEV_CONFIG2 (SXP_BLOCK+0x44) /* RW*: Device Config Reg #2 */ 507 #define SXP_PHASE_PTR (SXP_BLOCK+0x48) /* RW*: SCSI Phase Pointer */ 508 #define SXP_BUF_PTR (SXP_BLOCK+0x4C) /* RW*: SCSI Buffer Pointer */ 509 #define SXP_BUF_CTR (SXP_BLOCK+0x50) /* RW*: SCSI Buffer Counter */ 510 #define SXP_BUFFER (SXP_BLOCK+0x52) /* RW*: SCSI Buffer */ 511 #define SXP_BUF_BYTE (SXP_BLOCK+0x54) /* RW*: SCSI Buffer Byte */ 512 #define SXP_BUF_WD (SXP_BLOCK+0x56) /* RW*: SCSI Buffer Word */ 513 #define SXP_BUF_WD_TRAN (SXP_BLOCK+0x58) /* RW*: SCSI Buffer Wd xlate */ 514 #define SXP_FIFO (SXP_BLOCK+0x5A) /* RW*: SCSI FIFO */ 515 #define SXP_FIFO_STATUS (SXP_BLOCK+0x5C) /* RW*: SCSI FIFO Status */ 516 #define SXP_FIFO_TOP (SXP_BLOCK+0x5E) /* RW*: SCSI FIFO Top Resid */ 517 #define SXP_FIFO_BOTTOM (SXP_BLOCK+0x60) /* RW*: SCSI FIFO Bot Resid */ 518 #define SXP_TRAN_REG (SXP_BLOCK+0x64) /* RW*: SCSI Transferr Reg */ 519 #define SXP_TRAN_CNT_LO (SXP_BLOCK+0x68) /* RW*: SCSI Trans Count */ 520 #define SXP_TRAN_CNT_HI (SXP_BLOCK+0x6A) /* RW*: SCSI Trans Count */ 521 #define SXP_TRAN_CTR_LO (SXP_BLOCK+0x6C) /* RW*: SCSI Trans Counter */ 522 #define SXP_TRAN_CTR_HI (SXP_BLOCK+0x6E) /* RW*: SCSI Trans Counter */ 523 #define SXP_ARB_DATA (SXP_BLOCK+0x70) /* R : SCSI Arb Data */ 524 #define SXP_PINS_CTRL (SXP_BLOCK+0x72) /* RW*: SCSI Control Pins */ 525 #define SXP_PINS_DATA (SXP_BLOCK+0x74) /* RW*: SCSI Data Pins */ 526 #define SXP_PINS_DIFF (SXP_BLOCK+0x76) /* RW*: SCSI Diff Pins */ 527 528 /* for 1080/1280/1240 only */ 529 #define SXP_BANK1_SELECT 0x100 530 531 532 /* SXP CONF1 REGISTER */ 533 #define SXP_CONF1_ASYNCH_SETUP 0xF000 /* Asynchronous setup time */ 534 #define SXP_CONF1_SELECTION_UNIT 0x0000 /* Selection time unit */ 535 #define SXP_CONF1_SELECTION_TIMEOUT 0x0600 /* Selection timeout */ 536 #define SXP_CONF1_CLOCK_FACTOR 0x00E0 /* Clock factor */ 537 #define SXP_CONF1_SCSI_ID 0x000F /* SCSI id */ 538 539 /* SXP CONF2 REGISTER */ 540 #define SXP_CONF2_DISABLE_FILTER 0x0040 /* Disable SCSI rec filters */ 541 #define SXP_CONF2_REQ_ACK_PULLUPS 0x0020 /* Enable req/ack pullups */ 542 #define SXP_CONF2_DATA_PULLUPS 0x0010 /* Enable data pullups */ 543 #define SXP_CONF2_CONFIG_AUTOLOAD 0x0008 /* Enable dev conf auto-load */ 544 #define SXP_CONF2_RESELECT 0x0002 /* Enable reselection */ 545 #define SXP_CONF2_SELECT 0x0001 /* Enable selection */ 546 547 /* SXP INTERRUPT REGISTER */ 548 #define SXP_INT_PARITY_ERR 0x8000 /* Parity error detected */ 549 #define SXP_INT_GROSS_ERR 0x4000 /* Gross error detected */ 550 #define SXP_INT_FUNCTION_ABORT 0x2000 /* Last cmd aborted */ 551 #define SXP_INT_CONDITION_FAILED 0x1000 /* Last cond failed test */ 552 #define SXP_INT_FIFO_EMPTY 0x0800 /* SCSI FIFO is empty */ 553 #define SXP_INT_BUF_COUNTER_ZERO 0x0400 /* SCSI buf count == zero */ 554 #define SXP_INT_XFER_ZERO 0x0200 /* SCSI trans count == zero */ 555 #define SXP_INT_INT_PENDING 0x0080 /* SXP interrupt pending */ 556 #define SXP_INT_CMD_RUNNING 0x0040 /* SXP is running a command */ 557 #define SXP_INT_INT_RETURN_CODE 0x000F /* Interrupt return code */ 558 559 560 /* SXP GROSS ERROR REGISTER */ 561 #define SXP_GROSS_OFFSET_RESID 0x0040 /* Req/Ack offset not zero */ 562 #define SXP_GROSS_OFFSET_UNDERFLOW 0x0020 /* Req/Ack offset underflow */ 563 #define SXP_GROSS_OFFSET_OVERFLOW 0x0010 /* Req/Ack offset overflow */ 564 #define SXP_GROSS_FIFO_UNDERFLOW 0x0008 /* SCSI FIFO underflow */ 565 #define SXP_GROSS_FIFO_OVERFLOW 0x0004 /* SCSI FIFO overflow */ 566 #define SXP_GROSS_WRITE_ERR 0x0002 /* SXP and RISC wrote to reg */ 567 #define SXP_GROSS_ILLEGAL_INST 0x0001 /* Bad inst loaded into SXP */ 568 569 /* SXP EXCEPTION REGISTER */ 570 #define SXP_EXCEPT_USER_0 0x8000 /* Enable user exception #0 */ 571 #define SXP_EXCEPT_USER_1 0x4000 /* Enable user exception #1 */ 572 #define PCI_SXP_EXCEPT_SCAM 0x0400 /* SCAM Selection enable */ 573 #define SXP_EXCEPT_BUS_FREE 0x0200 /* Enable Bus Free det */ 574 #define SXP_EXCEPT_TARGET_ATN 0x0100 /* Enable TGT mode atten det */ 575 #define SXP_EXCEPT_RESELECTED 0x0080 /* Enable ReSEL exc handling */ 576 #define SXP_EXCEPT_SELECTED 0x0040 /* Enable SEL exc handling */ 577 #define SXP_EXCEPT_ARBITRATION 0x0020 /* Enable ARB exc handling */ 578 #define SXP_EXCEPT_GROSS_ERR 0x0010 /* Enable gross error except */ 579 #define SXP_EXCEPT_BUS_RESET 0x0008 /* Enable Bus Reset except */ 580 581 /* SXP OVERRIDE REGISTER */ 582 #define SXP_ORIDE_EXT_TRIGGER 0x8000 /* Enable external trigger */ 583 #define SXP_ORIDE_STEP 0x4000 /* Enable single step mode */ 584 #define SXP_ORIDE_BREAKPOINT 0x2000 /* Enable breakpoint reg */ 585 #define SXP_ORIDE_PIN_WRITE 0x1000 /* Enable write to SCSI pins */ 586 #define SXP_ORIDE_FORCE_OUTPUTS 0x0800 /* Force SCSI outputs on */ 587 #define SXP_ORIDE_LOOPBACK 0x0400 /* Enable SCSI loopback mode */ 588 #define SXP_ORIDE_PARITY_TEST 0x0200 /* Enable parity test mode */ 589 #define SXP_ORIDE_TRISTATE_ENA_PINS 0x0100 /* Tristate SCSI enable pins */ 590 #define SXP_ORIDE_TRISTATE_PINS 0x0080 /* Tristate SCSI pins */ 591 #define SXP_ORIDE_FIFO_RESET 0x0008 /* Reset SCSI FIFO */ 592 #define SXP_ORIDE_CMD_TERMINATE 0x0004 /* Terminate cur SXP com */ 593 #define SXP_ORIDE_RESET_REG 0x0002 /* Reset SXP registers */ 594 #define SXP_ORIDE_RESET_MODULE 0x0001 /* Reset SXP module */ 595 596 /* SXP COMMANDS */ 597 #define SXP_RESET_BUS_CMD 0x300b 598 599 /* SXP SCSI ID REGISTER */ 600 #define SXP_SELECTING_ID 0x0F00 /* (Re)Selecting id */ 601 #define SXP_SELECT_ID 0x000F /* Select id */ 602 603 /* SXP DEV CONFIG1 REGISTER */ 604 #define SXP_DCONF1_SYNC_HOLD 0x7000 /* Synchronous data hold */ 605 #define SXP_DCONF1_SYNC_SETUP 0x0F00 /* Synchronous data setup */ 606 #define SXP_DCONF1_SYNC_OFFSET 0x000F /* Synchronous data offset */ 607 608 609 /* SXP DEV CONFIG2 REGISTER */ 610 #define SXP_DCONF2_FLAGS_MASK 0xF000 /* Device flags */ 611 #define SXP_DCONF2_WIDE 0x0400 /* Enable wide SCSI */ 612 #define SXP_DCONF2_PARITY 0x0200 /* Enable parity checking */ 613 #define SXP_DCONF2_BLOCK_MODE 0x0100 /* Enable blk mode xfr count */ 614 #define SXP_DCONF2_ASSERTION_MASK 0x0007 /* Assersion period mask */ 615 616 617 /* SXP PHASE POINTER REGISTER */ 618 #define SXP_PHASE_STATUS_PTR 0x1000 /* Status buffer offset */ 619 #define SXP_PHASE_MSG_IN_PTR 0x0700 /* Msg in buffer offset */ 620 #define SXP_PHASE_COM_PTR 0x00F0 /* Command buffer offset */ 621 #define SXP_PHASE_MSG_OUT_PTR 0x0007 /* Msg out buffer offset */ 622 623 624 /* SXP FIFO STATUS REGISTER */ 625 #define SXP_FIFO_TOP_RESID 0x8000 /* Top residue reg full */ 626 #define SXP_FIFO_ACK_RESID 0x4000 /* Wide transfers odd resid */ 627 #define SXP_FIFO_COUNT_MASK 0x001C /* Words in SXP FIFO */ 628 #define SXP_FIFO_BOTTOM_RESID 0x0001 /* Bottom residue reg full */ 629 630 631 /* SXP CONTROL PINS REGISTER */ 632 #define SXP_PINS_CON_PHASE 0x8000 /* Scsi phase valid */ 633 #define SXP_PINS_CON_PARITY_HI 0x0400 /* Parity pin */ 634 #define SXP_PINS_CON_PARITY_LO 0x0200 /* Parity pin */ 635 #define SXP_PINS_CON_REQ 0x0100 /* SCSI bus REQUEST */ 636 #define SXP_PINS_CON_ACK 0x0080 /* SCSI bus ACKNOWLEDGE */ 637 #define SXP_PINS_CON_RST 0x0040 /* SCSI bus RESET */ 638 #define SXP_PINS_CON_BSY 0x0020 /* SCSI bus BUSY */ 639 #define SXP_PINS_CON_SEL 0x0010 /* SCSI bus SELECT */ 640 #define SXP_PINS_CON_ATN 0x0008 /* SCSI bus ATTENTION */ 641 #define SXP_PINS_CON_MSG 0x0004 /* SCSI bus MESSAGE */ 642 #define SXP_PINS_CON_CD 0x0002 /* SCSI bus COMMAND */ 643 #define SXP_PINS_CON_IO 0x0001 /* SCSI bus INPUT */ 644 645 /* 646 * Set the hold time for the SCSI Bus Reset to be 250 ms 647 */ 648 #define SXP_SCSI_BUS_RESET_HOLD_TIME 250 649 650 /* SXP DIFF PINS REGISTER */ 651 #define SXP_PINS_DIFF_SENSE 0x0200 /* DIFFSENS sig on SCSI bus */ 652 #define SXP_PINS_DIFF_MODE 0x0100 /* DIFFM signal */ 653 #define SXP_PINS_DIFF_ENABLE_OUTPUT 0x0080 /* Enable SXP SCSI data drv */ 654 #define SXP_PINS_DIFF_PINS_MASK 0x007C /* Differential control pins */ 655 #define SXP_PINS_DIFF_TARGET 0x0002 /* Enable SXP target mode */ 656 #define SXP_PINS_DIFF_INITIATOR 0x0001 /* Enable SXP initiator mode */ 657 658 /* Ultra2 only */ 659 #define SXP_PINS_LVD_MODE 0x1000 660 #define SXP_PINS_HVD_MODE 0x0800 661 #define SXP_PINS_SE_MODE 0x0400 662 #define SXP_PINS_MODE_MASK (SXP_PINS_LVD_MODE|SXP_PINS_HVD_MODE|SXP_PINS_SE_MODE) 663 664 /* The above have to be put together with the DIFFM pin to make sense */ 665 #define ISP1080_LVD_MODE (SXP_PINS_LVD_MODE) 666 #define ISP1080_HVD_MODE (SXP_PINS_HVD_MODE|SXP_PINS_DIFF_MODE) 667 #define ISP1080_SE_MODE (SXP_PINS_SE_MODE) 668 #define ISP1080_MODE_MASK (SXP_PINS_MODE_MASK|SXP_PINS_DIFF_MODE) 669 670 /* 671 * RISC and Host Command and Control Block Register Offsets 672 */ 673 674 #define RISC_ACC RISC_BLOCK+0x0 /* RW*: Accumulator */ 675 #define RISC_R1 RISC_BLOCK+0x2 /* RW*: GP Reg R1 */ 676 #define RISC_R2 RISC_BLOCK+0x4 /* RW*: GP Reg R2 */ 677 #define RISC_R3 RISC_BLOCK+0x6 /* RW*: GP Reg R3 */ 678 #define RISC_R4 RISC_BLOCK+0x8 /* RW*: GP Reg R4 */ 679 #define RISC_R5 RISC_BLOCK+0xA /* RW*: GP Reg R5 */ 680 #define RISC_R6 RISC_BLOCK+0xC /* RW*: GP Reg R6 */ 681 #define RISC_R7 RISC_BLOCK+0xE /* RW*: GP Reg R7 */ 682 #define RISC_R8 RISC_BLOCK+0x10 /* RW*: GP Reg R8 */ 683 #define RISC_R9 RISC_BLOCK+0x12 /* RW*: GP Reg R9 */ 684 #define RISC_R10 RISC_BLOCK+0x14 /* RW*: GP Reg R10 */ 685 #define RISC_R11 RISC_BLOCK+0x16 /* RW*: GP Reg R11 */ 686 #define RISC_R12 RISC_BLOCK+0x18 /* RW*: GP Reg R12 */ 687 #define RISC_R13 RISC_BLOCK+0x1a /* RW*: GP Reg R13 */ 688 #define RISC_R14 RISC_BLOCK+0x1c /* RW*: GP Reg R14 */ 689 #define RISC_R15 RISC_BLOCK+0x1e /* RW*: GP Reg R15 */ 690 #define RISC_PSR RISC_BLOCK+0x20 /* RW*: Processor Status */ 691 #define RISC_IVR RISC_BLOCK+0x22 /* RW*: Interrupt Vector */ 692 #define RISC_PCR RISC_BLOCK+0x24 /* RW*: Processor Ctrl */ 693 #define RISC_RAR0 RISC_BLOCK+0x26 /* RW*: Ram Address #0 */ 694 #define RISC_RAR1 RISC_BLOCK+0x28 /* RW*: Ram Address #1 */ 695 #define RISC_LCR RISC_BLOCK+0x2a /* RW*: Loop Counter */ 696 #define RISC_PC RISC_BLOCK+0x2c /* R : Program Counter */ 697 #define RISC_MTR RISC_BLOCK+0x2e /* RW*: Memory Timing */ 698 #define RISC_MTR2100 RISC_BLOCK+0x30 699 700 #define RISC_EMB RISC_BLOCK+0x30 /* RW*: Ext Mem Boundary */ 701 #define DUAL_BANK 8 702 #define RISC_SP RISC_BLOCK+0x32 /* RW*: Stack Pointer */ 703 #define RISC_HRL RISC_BLOCK+0x3e /* R *: Hardware Rev Level */ 704 #define HCCR RISC_BLOCK+0x40 /* RW : Host Command & Ctrl */ 705 #define BP0 RISC_BLOCK+0x42 /* RW : Processor Brkpt #0 */ 706 #define BP1 RISC_BLOCK+0x44 /* RW : Processor Brkpt #1 */ 707 #define TCR RISC_BLOCK+0x46 /* W : Test Control */ 708 #define TMR RISC_BLOCK+0x48 /* W : Test Mode */ 709 710 711 /* PROCESSOR STATUS REGISTER */ 712 #define RISC_PSR_FORCE_TRUE 0x8000 713 #define RISC_PSR_LOOP_COUNT_DONE 0x4000 714 #define RISC_PSR_RISC_INT 0x2000 715 #define RISC_PSR_TIMER_ROLLOVER 0x1000 716 #define RISC_PSR_ALU_OVERFLOW 0x0800 717 #define RISC_PSR_ALU_MSB 0x0400 718 #define RISC_PSR_ALU_CARRY 0x0200 719 #define RISC_PSR_ALU_ZERO 0x0100 720 721 #define RISC_PSR_PCI_ULTRA 0x0080 722 #define RISC_PSR_SBUS_ULTRA 0x0020 723 724 #define RISC_PSR_DMA_INT 0x0010 725 #define RISC_PSR_SXP_INT 0x0008 726 #define RISC_PSR_HOST_INT 0x0004 727 #define RISC_PSR_INT_PENDING 0x0002 728 #define RISC_PSR_FORCE_FALSE 0x0001 729 730 731 /* Host Command and Control */ 732 #define HCCR_CMD_NOP 0x0000 /* NOP */ 733 #define HCCR_CMD_RESET 0x1000 /* Reset RISC */ 734 #define HCCR_CMD_PAUSE 0x2000 /* Pause RISC */ 735 #define HCCR_CMD_RELEASE 0x3000 /* Release Paused RISC */ 736 #define HCCR_CMD_STEP 0x4000 /* Single Step RISC */ 737 #define HCCR_2X00_DISABLE_PARITY_PAUSE 0x4001 /* 738 * Disable RISC pause on FPM 739 * parity error. 740 */ 741 #define HCCR_CMD_SET_HOST_INT 0x5000 /* Set Host Interrupt */ 742 #define HCCR_CMD_CLEAR_HOST_INT 0x6000 /* Clear Host Interrupt */ 743 #define HCCR_CMD_CLEAR_RISC_INT 0x7000 /* Clear RISC interrupt */ 744 #define HCCR_CMD_BREAKPOINT 0x8000 /* Change breakpoint enables */ 745 #define PCI_HCCR_CMD_BIOS 0x9000 /* Write BIOS (disable) */ 746 #define PCI_HCCR_CMD_PARITY 0xA000 /* Write parity enable */ 747 #define PCI_HCCR_CMD_PARITY_ERR 0xE000 /* Generate parity error */ 748 #define HCCR_CMD_TEST_MODE 0xF000 /* Set Test Mode */ 749 750 751 #define ISP2100_HCCR_PARITY_ENABLE_2 0x0400 752 #define ISP2100_HCCR_PARITY_ENABLE_1 0x0200 753 #define ISP2100_HCCR_PARITY_ENABLE_0 0x0100 754 #define ISP2100_HCCR_PARITY 0x0001 755 756 #define PCI_HCCR_PARITY 0x0400 /* Parity error flag */ 757 #define PCI_HCCR_PARITY_ENABLE_1 0x0200 /* Parity enable bank 1 */ 758 #define PCI_HCCR_PARITY_ENABLE_0 0x0100 /* Parity enable bank 0 */ 759 760 #define HCCR_HOST_INT 0x0080 /* R : Host interrupt set */ 761 #define HCCR_RESET 0x0040 /* R : reset in progress */ 762 #define HCCR_PAUSE 0x0020 /* R : RISC paused */ 763 764 #define PCI_HCCR_BIOS 0x0001 /* W : BIOS enable */ 765 766 /* 767 * Defines for Interrupts 768 */ 769 #define ISP_INTS_ENABLED(isp) \ 770 ((IS_SCSI(isp))? \ 771 (ISP_READ(isp, BIU_ICR) & BIU_IMASK) : \ 772 (IS_24XX(isp)? (ISP_READ(isp, BIU2400_ICR) & BIU2400_IMASK) : \ 773 (ISP_READ(isp, BIU_ICR) & BIU2100_IMASK))) 774 775 #define ISP_ENABLE_INTS(isp) \ 776 (IS_SCSI(isp) ? \ 777 ISP_WRITE(isp, BIU_ICR, BIU_IMASK) : \ 778 (IS_24XX(isp) ? \ 779 (ISP_WRITE(isp, BIU2400_ICR, BIU2400_IMASK)) : \ 780 (ISP_WRITE(isp, BIU_ICR, BIU2100_IMASK)))) 781 782 #define ISP_DISABLE_INTS(isp) \ 783 IS_24XX(isp)? ISP_WRITE(isp, BIU2400_ICR, 0) : ISP_WRITE(isp, BIU_ICR, 0) 784 785 /* 786 * NVRAM Definitions (PCI cards only) 787 */ 788 789 #define ISPBSMX(c, byte, shift, mask) \ 790 (((c)[(byte)] >> (shift)) & (mask)) 791 /* 792 * Qlogic 1020/1040 NVRAM is an array of 128 bytes. 793 * 794 * Some portion of the front of this is for general host adapter properties 795 * This is followed by an array of per-target parameters, and is tailed off 796 * with a checksum xor byte at offset 127. For non-byte entities data is 797 * stored in Little Endian order. 798 */ 799 800 #define ISP_NVRAM_SIZE 128 801 802 #define ISP_NVRAM_VERSION(c) (c)[4] 803 #define ISP_NVRAM_FIFO_THRESHOLD(c) ISPBSMX(c, 5, 0, 0x03) 804 #define ISP_NVRAM_BIOS_DISABLE(c) ISPBSMX(c, 5, 2, 0x01) 805 #define ISP_NVRAM_HBA_ENABLE(c) ISPBSMX(c, 5, 3, 0x01) 806 #define ISP_NVRAM_INITIATOR_ID(c) ISPBSMX(c, 5, 4, 0x0f) 807 #define ISP_NVRAM_BUS_RESET_DELAY(c) (c)[6] 808 #define ISP_NVRAM_BUS_RETRY_COUNT(c) (c)[7] 809 #define ISP_NVRAM_BUS_RETRY_DELAY(c) (c)[8] 810 #define ISP_NVRAM_ASYNC_DATA_SETUP_TIME(c) ISPBSMX(c, 9, 0, 0x0f) 811 #define ISP_NVRAM_REQ_ACK_ACTIVE_NEGATION(c) ISPBSMX(c, 9, 4, 0x01) 812 #define ISP_NVRAM_DATA_LINE_ACTIVE_NEGATION(c) ISPBSMX(c, 9, 5, 0x01) 813 #define ISP_NVRAM_DATA_DMA_BURST_ENABLE(c) ISPBSMX(c, 9, 6, 0x01) 814 #define ISP_NVRAM_CMD_DMA_BURST_ENABLE(c) ISPBSMX(c, 9, 7, 0x01) 815 #define ISP_NVRAM_TAG_AGE_LIMIT(c) (c)[10] 816 #define ISP_NVRAM_LOWTRM_ENABLE(c) ISPBSMX(c, 11, 0, 0x01) 817 #define ISP_NVRAM_HITRM_ENABLE(c) ISPBSMX(c, 11, 1, 0x01) 818 #define ISP_NVRAM_PCMC_BURST_ENABLE(c) ISPBSMX(c, 11, 2, 0x01) 819 #define ISP_NVRAM_ENABLE_60_MHZ(c) ISPBSMX(c, 11, 3, 0x01) 820 #define ISP_NVRAM_SCSI_RESET_DISABLE(c) ISPBSMX(c, 11, 4, 0x01) 821 #define ISP_NVRAM_ENABLE_AUTO_TERM(c) ISPBSMX(c, 11, 5, 0x01) 822 #define ISP_NVRAM_FIFO_THRESHOLD_128(c) ISPBSMX(c, 11, 6, 0x01) 823 #define ISP_NVRAM_AUTO_TERM_SUPPORT(c) ISPBSMX(c, 11, 7, 0x01) 824 #define ISP_NVRAM_SELECTION_TIMEOUT(c) (((c)[12]) | ((c)[13] << 8)) 825 #define ISP_NVRAM_MAX_QUEUE_DEPTH(c) (((c)[14]) | ((c)[15] << 8)) 826 #define ISP_NVRAM_SCSI_BUS_SIZE(c) ISPBSMX(c, 16, 0, 0x01) 827 #define ISP_NVRAM_SCSI_BUS_TYPE(c) ISPBSMX(c, 16, 1, 0x01) 828 #define ISP_NVRAM_ADAPTER_CLK_SPEED(c) ISPBSMX(c, 16, 2, 0x01) 829 #define ISP_NVRAM_SOFT_TERM_SUPPORT(c) ISPBSMX(c, 16, 3, 0x01) 830 #define ISP_NVRAM_FLASH_ONBOARD(c) ISPBSMX(c, 16, 4, 0x01) 831 #define ISP_NVRAM_FAST_MTTR_ENABLE(c) ISPBSMX(c, 22, 0, 0x01) 832 833 #define ISP_NVRAM_TARGOFF 28 834 #define ISP_NVRAM_TARGSIZE 6 835 #define _IxT(tgt, tidx) \ 836 (ISP_NVRAM_TARGOFF + (ISP_NVRAM_TARGSIZE * (tgt)) + (tidx)) 837 #define ISP_NVRAM_TGT_RENEG(c, t) ISPBSMX(c, _IxT(t, 0), 0, 0x01) 838 #define ISP_NVRAM_TGT_QFRZ(c, t) ISPBSMX(c, _IxT(t, 0), 1, 0x01) 839 #define ISP_NVRAM_TGT_ARQ(c, t) ISPBSMX(c, _IxT(t, 0), 2, 0x01) 840 #define ISP_NVRAM_TGT_TQING(c, t) ISPBSMX(c, _IxT(t, 0), 3, 0x01) 841 #define ISP_NVRAM_TGT_SYNC(c, t) ISPBSMX(c, _IxT(t, 0), 4, 0x01) 842 #define ISP_NVRAM_TGT_WIDE(c, t) ISPBSMX(c, _IxT(t, 0), 5, 0x01) 843 #define ISP_NVRAM_TGT_PARITY(c, t) ISPBSMX(c, _IxT(t, 0), 6, 0x01) 844 #define ISP_NVRAM_TGT_DISC(c, t) ISPBSMX(c, _IxT(t, 0), 7, 0x01) 845 #define ISP_NVRAM_TGT_EXEC_THROTTLE(c, t) ISPBSMX(c, _IxT(t, 1), 0, 0xff) 846 #define ISP_NVRAM_TGT_SYNC_PERIOD(c, t) ISPBSMX(c, _IxT(t, 2), 0, 0xff) 847 #define ISP_NVRAM_TGT_SYNC_OFFSET(c, t) ISPBSMX(c, _IxT(t, 3), 0, 0x0f) 848 #define ISP_NVRAM_TGT_DEVICE_ENABLE(c, t) ISPBSMX(c, _IxT(t, 3), 4, 0x01) 849 #define ISP_NVRAM_TGT_LUN_DISABLE(c, t) ISPBSMX(c, _IxT(t, 3), 5, 0x01) 850 851 /* 852 * Qlogic 1080/1240 NVRAM is an array of 256 bytes. 853 * 854 * Some portion of the front of this is for general host adapter properties 855 * This is followed by an array of per-target parameters, and is tailed off 856 * with a checksum xor byte at offset 256. For non-byte entities data is 857 * stored in Little Endian order. 858 */ 859 860 #define ISP1080_NVRAM_SIZE 256 861 862 #define ISP1080_NVRAM_VERSION(c) ISP_NVRAM_VERSION(c) 863 864 /* Offset 5 */ 865 /* 866 uint8_t bios_configuration_mode :2; 867 uint8_t bios_disable :1; 868 uint8_t selectable_scsi_boot_enable :1; 869 uint8_t cd_rom_boot_enable :1; 870 uint8_t disable_loading_risc_code :1; 871 uint8_t enable_64bit_addressing :1; 872 uint8_t unused_7 :1; 873 */ 874 875 /* Offsets 6, 7 */ 876 /* 877 uint8_t boot_lun_number :5; 878 uint8_t scsi_bus_number :1; 879 uint8_t unused_6 :1; 880 uint8_t unused_7 :1; 881 uint8_t boot_target_number :4; 882 uint8_t unused_12 :1; 883 uint8_t unused_13 :1; 884 uint8_t unused_14 :1; 885 uint8_t unused_15 :1; 886 */ 887 888 #define ISP1080_NVRAM_HBA_ENABLE(c) ISPBSMX(c, 16, 3, 0x01) 889 890 #define ISP1080_NVRAM_BURST_ENABLE(c) ISPBSMX(c, 16, 1, 0x01) 891 #define ISP1080_NVRAM_FIFO_THRESHOLD(c) ISPBSMX(c, 16, 4, 0x0f) 892 893 #define ISP1080_NVRAM_AUTO_TERM_SUPPORT(c) ISPBSMX(c, 17, 7, 0x01) 894 #define ISP1080_NVRAM_BUS0_TERM_MODE(c) ISPBSMX(c, 17, 0, 0x03) 895 #define ISP1080_NVRAM_BUS1_TERM_MODE(c) ISPBSMX(c, 17, 2, 0x03) 896 897 #define ISP1080_ISP_PARAMETER(c) \ 898 (((c)[18]) | ((c)[19] << 8)) 899 900 #define ISP1080_FAST_POST(c) ISPBSMX(c, 20, 0, 0x01) 901 #define ISP1080_REPORT_LVD_TRANSITION(c) ISPBSMX(c, 20, 1, 0x01) 902 903 #define ISP1080_BUS1_OFF 112 904 905 #define ISP1080_NVRAM_INITIATOR_ID(c, b) \ 906 ISPBSMX(c, ((b == 0)? 0 : ISP1080_BUS1_OFF) + 24, 0, 0x0f) 907 #define ISP1080_NVRAM_BUS_RESET_DELAY(c, b) \ 908 (c)[((b == 0)? 0 : ISP1080_BUS1_OFF) + 25] 909 #define ISP1080_NVRAM_BUS_RETRY_COUNT(c, b) \ 910 (c)[((b == 0)? 0 : ISP1080_BUS1_OFF) + 26] 911 #define ISP1080_NVRAM_BUS_RETRY_DELAY(c, b) \ 912 (c)[((b == 0)? 0 : ISP1080_BUS1_OFF) + 27] 913 914 #define ISP1080_NVRAM_ASYNC_DATA_SETUP_TIME(c, b) \ 915 ISPBSMX(c, ((b == 0)? 0 : ISP1080_BUS1_OFF) + 28, 0, 0x0f) 916 #define ISP1080_NVRAM_REQ_ACK_ACTIVE_NEGATION(c, b) \ 917 ISPBSMX(c, ((b == 0)? 0 : ISP1080_BUS1_OFF) + 28, 4, 0x01) 918 #define ISP1080_NVRAM_DATA_LINE_ACTIVE_NEGATION(c, b) \ 919 ISPBSMX(c, ((b == 0)? 0 : ISP1080_BUS1_OFF) + 28, 5, 0x01) 920 #define ISP1080_NVRAM_SELECTION_TIMEOUT(c, b) \ 921 (((c)[((b == 0)? 0 : ISP1080_BUS1_OFF) + 30]) | \ 922 ((c)[((b == 0)? 0 : ISP1080_BUS1_OFF) + 31] << 8)) 923 #define ISP1080_NVRAM_MAX_QUEUE_DEPTH(c, b) \ 924 (((c)[((b == 0)? 0 : ISP1080_BUS1_OFF) + 32]) | \ 925 ((c)[((b == 0)? 0 : ISP1080_BUS1_OFF) + 33] << 8)) 926 927 #define ISP1080_NVRAM_TARGOFF(b) \ 928 ((b == 0)? 40: (40 + ISP1080_BUS1_OFF)) 929 #define ISP1080_NVRAM_TARGSIZE 6 930 #define _IxT8(tgt, tidx, b) \ 931 (ISP1080_NVRAM_TARGOFF((b)) + (ISP1080_NVRAM_TARGSIZE * (tgt)) + (tidx)) 932 933 #define ISP1080_NVRAM_TGT_RENEG(c, t, b) \ 934 ISPBSMX(c, _IxT8(t, 0, (b)), 0, 0x01) 935 #define ISP1080_NVRAM_TGT_QFRZ(c, t, b) \ 936 ISPBSMX(c, _IxT8(t, 0, (b)), 1, 0x01) 937 #define ISP1080_NVRAM_TGT_ARQ(c, t, b) \ 938 ISPBSMX(c, _IxT8(t, 0, (b)), 2, 0x01) 939 #define ISP1080_NVRAM_TGT_TQING(c, t, b) \ 940 ISPBSMX(c, _IxT8(t, 0, (b)), 3, 0x01) 941 #define ISP1080_NVRAM_TGT_SYNC(c, t, b) \ 942 ISPBSMX(c, _IxT8(t, 0, (b)), 4, 0x01) 943 #define ISP1080_NVRAM_TGT_WIDE(c, t, b) \ 944 ISPBSMX(c, _IxT8(t, 0, (b)), 5, 0x01) 945 #define ISP1080_NVRAM_TGT_PARITY(c, t, b) \ 946 ISPBSMX(c, _IxT8(t, 0, (b)), 6, 0x01) 947 #define ISP1080_NVRAM_TGT_DISC(c, t, b) \ 948 ISPBSMX(c, _IxT8(t, 0, (b)), 7, 0x01) 949 #define ISP1080_NVRAM_TGT_EXEC_THROTTLE(c, t, b) \ 950 ISPBSMX(c, _IxT8(t, 1, (b)), 0, 0xff) 951 #define ISP1080_NVRAM_TGT_SYNC_PERIOD(c, t, b) \ 952 ISPBSMX(c, _IxT8(t, 2, (b)), 0, 0xff) 953 #define ISP1080_NVRAM_TGT_SYNC_OFFSET(c, t, b) \ 954 ISPBSMX(c, _IxT8(t, 3, (b)), 0, 0x0f) 955 #define ISP1080_NVRAM_TGT_DEVICE_ENABLE(c, t, b) \ 956 ISPBSMX(c, _IxT8(t, 3, (b)), 4, 0x01) 957 #define ISP1080_NVRAM_TGT_LUN_DISABLE(c, t, b) \ 958 ISPBSMX(c, _IxT8(t, 3, (b)), 5, 0x01) 959 960 #define ISP12160_NVRAM_HBA_ENABLE ISP1080_NVRAM_HBA_ENABLE 961 #define ISP12160_NVRAM_BURST_ENABLE ISP1080_NVRAM_BURST_ENABLE 962 #define ISP12160_NVRAM_FIFO_THRESHOLD ISP1080_NVRAM_FIFO_THRESHOLD 963 #define ISP12160_NVRAM_AUTO_TERM_SUPPORT ISP1080_NVRAM_AUTO_TERM_SUPPORT 964 #define ISP12160_NVRAM_BUS0_TERM_MODE ISP1080_NVRAM_BUS0_TERM_MODE 965 #define ISP12160_NVRAM_BUS1_TERM_MODE ISP1080_NVRAM_BUS1_TERM_MODE 966 #define ISP12160_ISP_PARAMETER ISP12160_ISP_PARAMETER 967 #define ISP12160_FAST_POST ISP1080_FAST_POST 968 #define ISP12160_REPORT_LVD_TRANSITION ISP1080_REPORT_LVD_TRANSTION 969 970 #define ISP12160_NVRAM_INITIATOR_ID \ 971 ISP1080_NVRAM_INITIATOR_ID 972 #define ISP12160_NVRAM_BUS_RESET_DELAY \ 973 ISP1080_NVRAM_BUS_RESET_DELAY 974 #define ISP12160_NVRAM_BUS_RETRY_COUNT \ 975 ISP1080_NVRAM_BUS_RETRY_COUNT 976 #define ISP12160_NVRAM_BUS_RETRY_DELAY \ 977 ISP1080_NVRAM_BUS_RETRY_DELAY 978 #define ISP12160_NVRAM_ASYNC_DATA_SETUP_TIME \ 979 ISP1080_NVRAM_ASYNC_DATA_SETUP_TIME 980 #define ISP12160_NVRAM_REQ_ACK_ACTIVE_NEGATION \ 981 ISP1080_NVRAM_REQ_ACK_ACTIVE_NEGATION 982 #define ISP12160_NVRAM_DATA_LINE_ACTIVE_NEGATION \ 983 ISP1080_NVRAM_DATA_LINE_ACTIVE_NEGATION 984 #define ISP12160_NVRAM_SELECTION_TIMEOUT \ 985 ISP1080_NVRAM_SELECTION_TIMEOUT 986 #define ISP12160_NVRAM_MAX_QUEUE_DEPTH \ 987 ISP1080_NVRAM_MAX_QUEUE_DEPTH 988 989 990 #define ISP12160_BUS0_OFF 24 991 #define ISP12160_BUS1_OFF 136 992 993 #define ISP12160_NVRAM_TARGOFF(b) \ 994 (((b == 0)? ISP12160_BUS0_OFF : ISP12160_BUS1_OFF) + 16) 995 996 #define ISP12160_NVRAM_TARGSIZE 6 997 #define _IxT16(tgt, tidx, b) \ 998 (ISP12160_NVRAM_TARGOFF((b))+(ISP12160_NVRAM_TARGSIZE * (tgt))+(tidx)) 999 1000 #define ISP12160_NVRAM_TGT_RENEG(c, t, b) \ 1001 ISPBSMX(c, _IxT16(t, 0, (b)), 0, 0x01) 1002 #define ISP12160_NVRAM_TGT_QFRZ(c, t, b) \ 1003 ISPBSMX(c, _IxT16(t, 0, (b)), 1, 0x01) 1004 #define ISP12160_NVRAM_TGT_ARQ(c, t, b) \ 1005 ISPBSMX(c, _IxT16(t, 0, (b)), 2, 0x01) 1006 #define ISP12160_NVRAM_TGT_TQING(c, t, b) \ 1007 ISPBSMX(c, _IxT16(t, 0, (b)), 3, 0x01) 1008 #define ISP12160_NVRAM_TGT_SYNC(c, t, b) \ 1009 ISPBSMX(c, _IxT16(t, 0, (b)), 4, 0x01) 1010 #define ISP12160_NVRAM_TGT_WIDE(c, t, b) \ 1011 ISPBSMX(c, _IxT16(t, 0, (b)), 5, 0x01) 1012 #define ISP12160_NVRAM_TGT_PARITY(c, t, b) \ 1013 ISPBSMX(c, _IxT16(t, 0, (b)), 6, 0x01) 1014 #define ISP12160_NVRAM_TGT_DISC(c, t, b) \ 1015 ISPBSMX(c, _IxT16(t, 0, (b)), 7, 0x01) 1016 1017 #define ISP12160_NVRAM_TGT_EXEC_THROTTLE(c, t, b) \ 1018 ISPBSMX(c, _IxT16(t, 1, (b)), 0, 0xff) 1019 #define ISP12160_NVRAM_TGT_SYNC_PERIOD(c, t, b) \ 1020 ISPBSMX(c, _IxT16(t, 2, (b)), 0, 0xff) 1021 1022 #define ISP12160_NVRAM_TGT_SYNC_OFFSET(c, t, b) \ 1023 ISPBSMX(c, _IxT16(t, 3, (b)), 0, 0x1f) 1024 #define ISP12160_NVRAM_TGT_DEVICE_ENABLE(c, t, b) \ 1025 ISPBSMX(c, _IxT16(t, 3, (b)), 5, 0x01) 1026 1027 #define ISP12160_NVRAM_PPR_OPTIONS(c, t, b) \ 1028 ISPBSMX(c, _IxT16(t, 4, (b)), 0, 0x0f) 1029 #define ISP12160_NVRAM_PPR_WIDTH(c, t, b) \ 1030 ISPBSMX(c, _IxT16(t, 4, (b)), 4, 0x03) 1031 #define ISP12160_NVRAM_PPR_ENABLE(c, t, b) \ 1032 ISPBSMX(c, _IxT16(t, 4, (b)), 7, 0x01) 1033 1034 /* 1035 * Qlogic 2100 thru 2300 NVRAM is an array of 256 bytes. 1036 * 1037 * Some portion of the front of this is for general RISC engine parameters, 1038 * mostly reflecting the state of the last INITIALIZE FIRMWARE mailbox command. 1039 * 1040 * This is followed by some general host adapter parameters, and ends with 1041 * a checksum xor byte at offset 255. For non-byte entities data is stored 1042 * in Little Endian order. 1043 */ 1044 #define ISP2100_NVRAM_SIZE 256 1045 /* ISP_NVRAM_VERSION is in same overall place */ 1046 #define ISP2100_NVRAM_RISCVER(c) (c)[6] 1047 #define ISP2100_NVRAM_OPTIONS(c) ((c)[8] | ((c)[9] << 8)) 1048 #define ISP2100_NVRAM_MAXFRAMELENGTH(c) (((c)[10]) | ((c)[11] << 8)) 1049 #define ISP2100_NVRAM_MAXIOCBALLOCATION(c) (((c)[12]) | ((c)[13] << 8)) 1050 #define ISP2100_NVRAM_EXECUTION_THROTTLE(c) (((c)[14]) | ((c)[15] << 8)) 1051 #define ISP2100_NVRAM_RETRY_COUNT(c) (c)[16] 1052 #define ISP2100_NVRAM_RETRY_DELAY(c) (c)[17] 1053 1054 #define ISP2100_NVRAM_PORT_NAME(c) (\ 1055 (((uint64_t)(c)[18]) << 56) | \ 1056 (((uint64_t)(c)[19]) << 48) | \ 1057 (((uint64_t)(c)[20]) << 40) | \ 1058 (((uint64_t)(c)[21]) << 32) | \ 1059 (((uint64_t)(c)[22]) << 24) | \ 1060 (((uint64_t)(c)[23]) << 16) | \ 1061 (((uint64_t)(c)[24]) << 8) | \ 1062 (((uint64_t)(c)[25]) << 0)) 1063 1064 #define ISP2100_NVRAM_HARDLOOPID(c) ((c)[26] | ((c)[27] << 8)) 1065 #define ISP2100_NVRAM_TOV(c) ((c)[29]) 1066 1067 #define ISP2100_NVRAM_NODE_NAME(c) (\ 1068 (((uint64_t)(c)[30]) << 56) | \ 1069 (((uint64_t)(c)[31]) << 48) | \ 1070 (((uint64_t)(c)[32]) << 40) | \ 1071 (((uint64_t)(c)[33]) << 32) | \ 1072 (((uint64_t)(c)[34]) << 24) | \ 1073 (((uint64_t)(c)[35]) << 16) | \ 1074 (((uint64_t)(c)[36]) << 8) | \ 1075 (((uint64_t)(c)[37]) << 0)) 1076 1077 #define ISP2100_XFW_OPTIONS(c) ((c)[38] | ((c)[39] << 8)) 1078 1079 #define ISP2100_RACC_TIMER(c) (c)[40] 1080 #define ISP2100_IDELAY_TIMER(c) (c)[41] 1081 1082 #define ISP2100_ZFW_OPTIONS(c) ((c)[42] | ((c)[43] << 8)) 1083 1084 #define ISP2100_SERIAL_LINK(c) ((c)[68] | ((c)[69] << 8)) 1085 1086 #define ISP2100_NVRAM_HBA_OPTIONS(c) ((c)[70] | ((c)[71] << 8)) 1087 #define ISP2100_NVRAM_HBA_DISABLE(c) ISPBSMX(c, 70, 0, 0x01) 1088 #define ISP2100_NVRAM_BIOS_DISABLE(c) ISPBSMX(c, 70, 1, 0x01) 1089 #define ISP2100_NVRAM_LUN_DISABLE(c) ISPBSMX(c, 70, 2, 0x01) 1090 #define ISP2100_NVRAM_ENABLE_SELECT_BOOT(c) ISPBSMX(c, 70, 3, 0x01) 1091 #define ISP2100_NVRAM_DISABLE_CODELOAD(c) ISPBSMX(c, 70, 4, 0x01) 1092 #define ISP2100_NVRAM_SET_CACHELINESZ(c) ISPBSMX(c, 70, 5, 0x01) 1093 1094 #define ISP2100_NVRAM_BOOT_NODE_NAME(c) (\ 1095 (((uint64_t)(c)[72]) << 56) | \ 1096 (((uint64_t)(c)[73]) << 48) | \ 1097 (((uint64_t)(c)[74]) << 40) | \ 1098 (((uint64_t)(c)[75]) << 32) | \ 1099 (((uint64_t)(c)[76]) << 24) | \ 1100 (((uint64_t)(c)[77]) << 16) | \ 1101 (((uint64_t)(c)[78]) << 8) | \ 1102 (((uint64_t)(c)[79]) << 0)) 1103 1104 #define ISP2100_NVRAM_BOOT_LUN(c) (c)[80] 1105 #define ISP2100_RESET_DELAY(c) (c)[81] 1106 1107 #define ISP2100_HBA_FEATURES(c) ((c)[232] | ((c)[233] << 8)) 1108 1109 /* 1110 * Qlogic 2400 NVRAM is an array of 512 bytes with a 32 bit checksum. 1111 */ 1112 #define ISP2400_NVRAM_PORT0_ADDR 0x80 1113 #define ISP2400_NVRAM_PORT1_ADDR 0x180 1114 #define ISP2400_NVRAM_SIZE 512 1115 1116 #define ISP2400_NVRAM_VERSION(c) ((c)[4] | ((c)[5] << 8)) 1117 #define ISP2400_NVRAM_MAXFRAMELENGTH(c) (((c)[12]) | ((c)[13] << 8)) 1118 #define ISP2400_NVRAM_EXECUTION_THROTTLE(c) (((c)[14]) | ((c)[15] << 8)) 1119 #define ISP2400_NVRAM_EXCHANGE_COUNT(c) (((c)[16]) | ((c)[17] << 8)) 1120 #define ISP2400_NVRAM_HARDLOOPID(c) ((c)[18] | ((c)[19] << 8)) 1121 1122 #define ISP2400_NVRAM_PORT_NAME(c) (\ 1123 (((uint64_t)(c)[20]) << 56) | \ 1124 (((uint64_t)(c)[21]) << 48) | \ 1125 (((uint64_t)(c)[22]) << 40) | \ 1126 (((uint64_t)(c)[23]) << 32) | \ 1127 (((uint64_t)(c)[24]) << 24) | \ 1128 (((uint64_t)(c)[25]) << 16) | \ 1129 (((uint64_t)(c)[26]) << 8) | \ 1130 (((uint64_t)(c)[27]) << 0)) 1131 1132 #define ISP2400_NVRAM_NODE_NAME(c) (\ 1133 (((uint64_t)(c)[28]) << 56) | \ 1134 (((uint64_t)(c)[29]) << 48) | \ 1135 (((uint64_t)(c)[30]) << 40) | \ 1136 (((uint64_t)(c)[31]) << 32) | \ 1137 (((uint64_t)(c)[32]) << 24) | \ 1138 (((uint64_t)(c)[33]) << 16) | \ 1139 (((uint64_t)(c)[34]) << 8) | \ 1140 (((uint64_t)(c)[35]) << 0)) 1141 1142 #define ISP2400_NVRAM_LOGIN_RETRY_CNT(c) ((c)[36] | ((c)[37] << 8)) 1143 #define ISP2400_NVRAM_LINK_DOWN_ON_NOS(c) ((c)[38] | ((c)[39] << 8)) 1144 #define ISP2400_NVRAM_INTERRUPT_DELAY(c) ((c)[40] | ((c)[41] << 8)) 1145 #define ISP2400_NVRAM_LOGIN_TIMEOUT(c) ((c)[42] | ((c)[43] << 8)) 1146 1147 #define ISP2400_NVRAM_FIRMWARE_OPTIONS1(c) \ 1148 ((c)[44] | ((c)[45] << 8) | ((c)[46] << 16) | ((c)[47] << 24)) 1149 #define ISP2400_NVRAM_FIRMWARE_OPTIONS2(c) \ 1150 ((c)[48] | ((c)[49] << 8) | ((c)[50] << 16) | ((c)[51] << 24)) 1151 #define ISP2400_NVRAM_FIRMWARE_OPTIONS3(c) \ 1152 ((c)[52] | ((c)[53] << 8) | ((c)[54] << 16) | ((c)[55] << 24)) 1153 1154 /* 1155 * Firmware Crash Dump 1156 * 1157 * QLogic needs specific information format when they look at firmware crashes. 1158 * 1159 * This is incredibly kernel memory consumptive (to say the least), so this 1160 * code is only compiled in when needed. 1161 */ 1162 1163 #define QLA2200_RISC_IMAGE_DUMP_SIZE \ 1164 (1 * sizeof (uint16_t)) + /* 'used' flag (also HBA type) */ \ 1165 (352 * sizeof (uint16_t)) + /* RISC registers */ \ 1166 (61440 * sizeof (uint16_t)) /* RISC SRAM (offset 0x1000..0xffff) */ 1167 #define QLA2300_RISC_IMAGE_DUMP_SIZE \ 1168 (1 * sizeof (uint16_t)) + /* 'used' flag (also HBA type) */ \ 1169 (464 * sizeof (uint16_t)) + /* RISC registers */ \ 1170 (63488 * sizeof (uint16_t)) + /* RISC SRAM (0x0800..0xffff) */ \ 1171 (4096 * sizeof (uint16_t)) + /* RISC SRAM (0x10000..0x10FFF) */ \ 1172 (61440 * sizeof (uint16_t)) /* RISC SRAM (0x11000..0x1FFFF) */ 1173 /* the larger of the two */ 1174 #define ISP_CRASH_IMAGE_SIZE QLA2300_RISC_IMAGE_DUMP_SIZE 1175 #endif /* _ISPREG_H */ 1176