1 /* $FreeBSD$ */ 2 /*- 3 * SPDX-License-Identifier: BSD-2-Clause-FreeBSD 4 * 5 * Copyright (c) 2009-2018 Alexander Motin <mav@FreeBSD.org> 6 * Copyright (c) 1997-2009 by Matthew Jacob 7 * All rights reserved. 8 * 9 * Redistribution and use in source and binary forms, with or without 10 * modification, are permitted provided that the following conditions 11 * are met: 12 * 13 * 1. Redistributions of source code must retain the above copyright 14 * notice, this list of conditions and the following disclaimer. 15 * 2. Redistributions in binary form must reproduce the above copyright 16 * notice, this list of conditions and the following disclaimer in the 17 * documentation and/or other materials provided with the distribution. 18 * 19 * THIS SOFTWARE IS PROVIDED BY AUTHOR AND CONTRIBUTORS ``AS IS'' AND 20 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 21 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 22 * ARE DISCLAIMED. IN NO EVENT SHALL AUTHOR OR CONTRIBUTORS BE LIABLE 23 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 24 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 25 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 26 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 27 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 28 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 29 * SUCH DAMAGE. 30 * 31 */ 32 33 /* 34 * Mailbox and Queue Entry Definitions for for Qlogic ISP SCSI adapters. 35 */ 36 #ifndef _ISPMBOX_H 37 #define _ISPMBOX_H 38 39 /* 40 * Mailbox Command Opcodes 41 */ 42 #define MBOX_NO_OP 0x0000 43 #define MBOX_LOAD_RAM 0x0001 44 #define MBOX_EXEC_FIRMWARE 0x0002 45 #define MBOX_DUMP_RAM 0x0003 46 #define MBOX_WRITE_RAM_WORD 0x0004 47 #define MBOX_READ_RAM_WORD 0x0005 48 #define MBOX_MAILBOX_REG_TEST 0x0006 49 #define MBOX_VERIFY_CHECKSUM 0x0007 50 #define MBOX_ABOUT_FIRMWARE 0x0008 51 #define MBOX_LOAD_RISC_RAM_2100 0x0009 52 /* a */ 53 #define MBOX_LOAD_RISC_RAM 0x000b 54 #define MBOX_DUMP_RISC_RAM 0x000c 55 #define MBOX_WRITE_RAM_WORD_EXTENDED 0x000d 56 #define MBOX_CHECK_FIRMWARE 0x000e 57 #define MBOX_READ_RAM_WORD_EXTENDED 0x000f 58 #define MBOX_INIT_REQ_QUEUE 0x0010 59 #define MBOX_INIT_RES_QUEUE 0x0011 60 #define MBOX_EXECUTE_IOCB 0x0012 61 #define MBOX_WAKE_UP 0x0013 62 #define MBOX_STOP_FIRMWARE 0x0014 63 #define MBOX_ABORT 0x0015 64 #define MBOX_ABORT_DEVICE 0x0016 65 #define MBOX_ABORT_TARGET 0x0017 66 #define MBOX_BUS_RESET 0x0018 67 #define MBOX_STOP_QUEUE 0x0019 68 #define MBOX_START_QUEUE 0x001a 69 #define MBOX_SINGLE_STEP_QUEUE 0x001b 70 #define MBOX_ABORT_QUEUE 0x001c 71 #define MBOX_GET_DEV_QUEUE_STATUS 0x001d 72 /* 1e */ 73 #define MBOX_GET_FIRMWARE_STATUS 0x001f 74 #define MBOX_GET_INIT_SCSI_ID 0x0020 75 #define MBOX_GET_SELECT_TIMEOUT 0x0021 76 #define MBOX_GET_RETRY_COUNT 0x0022 77 #define MBOX_GET_TAG_AGE_LIMIT 0x0023 78 #define MBOX_GET_CLOCK_RATE 0x0024 79 #define MBOX_GET_ACT_NEG_STATE 0x0025 80 #define MBOX_GET_ASYNC_DATA_SETUP_TIME 0x0026 81 #define MBOX_GET_SBUS_PARAMS 0x0027 82 #define MBOX_GET_PCI_PARAMS MBOX_GET_SBUS_PARAMS 83 #define MBOX_GET_TARGET_PARAMS 0x0028 84 #define MBOX_GET_DEV_QUEUE_PARAMS 0x0029 85 #define MBOX_GET_RESET_DELAY_PARAMS 0x002a 86 /* 2b */ 87 /* 2c */ 88 /* 2d */ 89 /* 2e */ 90 /* 2f */ 91 #define MBOX_SET_INIT_SCSI_ID 0x0030 92 #define MBOX_SET_SELECT_TIMEOUT 0x0031 93 #define MBOX_SET_RETRY_COUNT 0x0032 94 #define MBOX_SET_TAG_AGE_LIMIT 0x0033 95 #define MBOX_SET_CLOCK_RATE 0x0034 96 #define MBOX_SET_ACT_NEG_STATE 0x0035 97 #define MBOX_SET_ASYNC_DATA_SETUP_TIME 0x0036 98 #define MBOX_SET_SBUS_CONTROL_PARAMS 0x0037 99 #define MBOX_SET_PCI_PARAMETERS 0x0037 100 #define MBOX_SET_TARGET_PARAMS 0x0038 101 #define MBOX_SET_DEV_QUEUE_PARAMS 0x0039 102 #define MBOX_SET_RESET_DELAY_PARAMS 0x003a 103 /* 3b */ 104 /* 3c */ 105 /* 3d */ 106 /* 3e */ 107 /* 3f */ 108 #define MBOX_RETURN_BIOS_BLOCK_ADDR 0x0040 109 #define MBOX_WRITE_FOUR_RAM_WORDS 0x0041 110 #define MBOX_EXEC_BIOS_IOCB 0x0042 111 #define MBOX_SET_FW_FEATURES 0x004a 112 #define MBOX_GET_FW_FEATURES 0x004b 113 #define FW_FEATURE_FAST_POST 0x1 114 #define FW_FEATURE_LVD_NOTIFY 0x2 115 #define FW_FEATURE_RIO_32BIT 0x4 116 #define FW_FEATURE_RIO_16BIT 0x8 117 118 #define MBOX_INIT_REQ_QUEUE_A64 0x0052 119 #define MBOX_INIT_RES_QUEUE_A64 0x0053 120 121 #define MBOX_ENABLE_TARGET_MODE 0x0055 122 #define ENABLE_TARGET_FLAG 0x8000 123 #define ENABLE_TQING_FLAG 0x0004 124 #define ENABLE_MANDATORY_DISC 0x0002 125 #define MBOX_GET_TARGET_STATUS 0x0056 126 127 /* These are for the ISP2X00 FC cards */ 128 #define MBOX_LOAD_FLASH_FIRMWARE 0x0003 129 #define MBOX_WRITE_FC_SERDES_REG 0x0003 /* FC only */ 130 #define MBOX_READ_FC_SERDES_REG 0x0004 /* FC only */ 131 #define MBOX_GET_IO_STATUS 0x0012 132 #define MBOX_SET_TRANSMIT_PARAMS 0x0019 133 #define MBOX_SET_PORT_PARAMS 0x001a 134 #define MBOX_LOAD_OP_FW_PARAMS 0x001b 135 #define MBOX_INIT_MULTIPLE_QUEUE 0x001f 136 #define MBOX_GET_LOOP_ID 0x0020 137 /* for 24XX cards, outgoing mailbox 7 has these values for F or FL topologies */ 138 #define ISP24XX_INORDER 0x0100 139 #define ISP24XX_NPIV_SAN 0x0400 140 #define ISP24XX_VSAN_SAN 0x1000 141 #define ISP24XX_FC_SP_SAN 0x2000 142 #define MBOX_GET_TIMEOUT_PARAMS 0x0022 143 #define MBOX_GET_FIRMWARE_OPTIONS 0x0028 144 #define MBOX_GENERATE_SYSTEM_ERROR 0x002a 145 #define MBOX_WRITE_SFP 0x0030 146 #define MBOX_READ_SFP 0x0031 147 #define MBOX_SET_TIMEOUT_PARAMS 0x0032 148 #define MBOX_SET_FIRMWARE_OPTIONS 0x0038 149 #define MBOX_GET_SET_FC_LED_CONF 0x003b 150 #define MBOX_RESTART_NIC_FIRMWARE 0x003d /* FCoE only */ 151 #define MBOX_ACCESS_CONTROL 0x003e 152 #define MBOX_LOOP_PORT_BYPASS 0x0040 /* FC only */ 153 #define MBOX_LOOP_PORT_ENABLE 0x0041 /* FC only */ 154 #define MBOX_GET_RESOURCE_COUNT 0x0042 155 #define MBOX_REQUEST_OFFLINE_MODE 0x0043 156 #define MBOX_DIAGNOSTIC_ECHO_TEST 0x0044 157 #define MBOX_DIAGNOSTIC_LOOPBACK 0x0045 158 #define MBOX_ENHANCED_GET_PDB 0x0047 159 #define MBOX_INIT_FIRMWARE_MULTI_ID 0x0048 /* 2400 only */ 160 #define MBOX_GET_VP_DATABASE 0x0049 /* 2400 only */ 161 #define MBOX_GET_VP_DATABASE_ENTRY 0x004a /* 2400 only */ 162 #define MBOX_GET_FCF_LIST 0x0050 /* FCoE only */ 163 #define MBOX_GET_DCBX_PARAMETERS 0x0051 /* FCoE only */ 164 #define MBOX_HOST_MEMORY_COPY 0x0053 165 #define MBOX_EXEC_COMMAND_IOCB_A64 0x0054 166 #define MBOX_SEND_RNID 0x0057 167 #define MBOX_SET_PARAMETERS 0x0059 168 #define MBOX_GET_PARAMETERS 0x005a 169 #define MBOX_DRIVER_HEARTBEAT 0x005B /* FC only */ 170 #define MBOX_FW_HEARTBEAT 0x005C 171 #define MBOX_GET_SET_DATA_RATE 0x005D /* >=23XX only */ 172 #define MBGSD_GET_RATE 0 173 #define MBGSD_SET_RATE 1 174 #define MBGSD_SET_RATE_NOW 2 /* 24XX only */ 175 #define MBGSD_1GB 0x00 176 #define MBGSD_2GB 0x01 177 #define MBGSD_AUTO 0x02 178 #define MBGSD_4GB 0x03 /* 24XX only */ 179 #define MBGSD_8GB 0x04 /* 25XX only */ 180 #define MBGSD_16GB 0x05 /* 26XX only */ 181 #define MBGSD_32GB 0x06 /* 27XX only */ 182 #define MBGSD_10GB 0x13 /* 26XX only */ 183 #define MBOX_SEND_RNFT 0x005e 184 #define MBOX_INIT_FIRMWARE 0x0060 185 #define MBOX_GET_INIT_CONTROL_BLOCK 0x0061 186 #define MBOX_INIT_LIP 0x0062 187 #define MBOX_GET_FC_AL_POSITION_MAP 0x0063 188 #define MBOX_GET_PORT_DB 0x0064 189 #define MBOX_CLEAR_ACA 0x0065 190 #define MBOX_TARGET_RESET 0x0066 191 #define MBOX_CLEAR_TASK_SET 0x0067 192 #define MBOX_ABORT_TASK_SET 0x0068 193 #define MBOX_GET_FW_STATE 0x0069 194 #define MBOX_GET_PORT_NAME 0x006A 195 #define MBOX_GET_LINK_STATUS 0x006B 196 #define MBOX_INIT_LIP_RESET 0x006C 197 #define MBOX_GET_LINK_STAT_PR_DATA_CNT 0x006D 198 #define MBOX_SEND_SNS 0x006E 199 #define MBOX_FABRIC_LOGIN 0x006F 200 #define MBOX_SEND_CHANGE_REQUEST 0x0070 201 #define MBOX_FABRIC_LOGOUT 0x0071 202 #define MBOX_INIT_LIP_LOGIN 0x0072 203 #define MBOX_GET_PORT_NODE_NAME_LIST 0x0075 204 #define MBOX_SET_VENDOR_ID 0x0076 205 #define MBOX_GET_XGMAC_STATS 0x007a 206 #define MBOX_GET_ID_LIST 0x007C 207 #define MBOX_SEND_LFA 0x007d 208 #define MBOX_LUN_RESET 0x007E 209 210 #define ISP2100_SET_PCI_PARAM 0x00ff 211 212 #define MBOX_BUSY 0x04 213 214 /* 215 * Mailbox Command Complete Status Codes 216 */ 217 #define MBOX_COMMAND_COMPLETE 0x4000 218 #define MBOX_INVALID_COMMAND 0x4001 219 #define MBOX_HOST_INTERFACE_ERROR 0x4002 220 #define MBOX_TEST_FAILED 0x4003 221 #define MBOX_COMMAND_ERROR 0x4005 222 #define MBOX_COMMAND_PARAM_ERROR 0x4006 223 #define MBOX_PORT_ID_USED 0x4007 224 #define MBOX_LOOP_ID_USED 0x4008 225 #define MBOX_ALL_IDS_USED 0x4009 226 #define MBOX_NOT_LOGGED_IN 0x400A 227 #define MBOX_LINK_DOWN_ERROR 0x400B 228 #define MBOX_LOOPBACK_ERROR 0x400C 229 #define MBOX_CHECKSUM_ERROR 0x4010 230 #define MBOX_INVALID_PRODUCT_KEY 0x4020 231 /* pseudo mailbox completion codes */ 232 #define MBOX_REGS_BUSY 0x6000 /* registers in use */ 233 #define MBOX_TIMEOUT 0x6001 /* command timed out */ 234 235 #define MBLOGALL 0xffffffff 236 #define MBLOGNONE 0x00000000 237 #define MBLOGMASK(x) (1 << (((x) - 1) & 0x1f)) 238 239 /* 240 * Asynchronous event status codes 241 */ 242 #define ASYNC_BUS_RESET 0x8001 243 #define ASYNC_SYSTEM_ERROR 0x8002 244 #define ASYNC_RQS_XFER_ERR 0x8003 245 #define ASYNC_RSP_XFER_ERR 0x8004 246 #define ASYNC_QWAKEUP 0x8005 247 #define ASYNC_TIMEOUT_RESET 0x8006 248 #define ASYNC_DEVICE_RESET 0x8007 249 #define ASYNC_EXTMSG_UNDERRUN 0x800A 250 #define ASYNC_SCAM_INT 0x800B 251 #define ASYNC_HUNG_SCSI 0x800C 252 #define ASYNC_KILLED_BUS 0x800D 253 #define ASYNC_BUS_TRANSIT 0x800E /* LVD -> HVD, eg. */ 254 #define ASYNC_LIP_OCCURRED 0x8010 /* FC only */ 255 #define ASYNC_LOOP_UP 0x8011 256 #define ASYNC_LOOP_DOWN 0x8012 257 #define ASYNC_LOOP_RESET 0x8013 /* FC only */ 258 #define ASYNC_PDB_CHANGED 0x8014 259 #define ASYNC_CHANGE_NOTIFY 0x8015 260 #define ASYNC_LIP_NOS_OLS_RECV 0x8016 /* FC only */ 261 #define ASYNC_LIP_ERROR 0x8017 /* FC only */ 262 #define ASYNC_AUTO_PLOGI_RJT 0x8018 263 #define ASYNC_SECURITY_UPDATE 0x801B 264 #define ASYNC_CMD_CMPLT 0x8020 265 #define ASYNC_CTIO_DONE 0x8021 266 #define ASYNC_RIO32_1 0x8021 267 #define ASYNC_RIO32_2 0x8022 268 #define ASYNC_IP_XMIT_DONE 0x8022 269 #define ASYNC_IP_RECV_DONE 0x8023 270 #define ASYNC_IP_BROADCAST 0x8024 271 #define ASYNC_IP_RCVQ_LOW 0x8025 272 #define ASYNC_IP_RCVQ_EMPTY 0x8026 273 #define ASYNC_IP_RECV_DONE_ALIGNED 0x8027 274 #define ASYNC_ERR_LOGGING_DISABLED 0x8029 275 #define ASYNC_PTPMODE 0x8030 /* FC only */ 276 #define ASYNC_RIO16_1 0x8031 277 #define ASYNC_RIO16_2 0x8032 278 #define ASYNC_RIO16_3 0x8033 279 #define ASYNC_RIO16_4 0x8034 280 #define ASYNC_RIO16_5 0x8035 281 #define ASYNC_CONNMODE 0x8036 282 #define ISP_CONN_LOOP 1 283 #define ISP_CONN_PTP 2 284 #define ISP_CONN_BADLIP 3 285 #define ISP_CONN_FATAL 4 286 #define ISP_CONN_LOOPBACK 5 287 #define ASYNC_P2P_INIT_ERR 0x8037 288 #define ASYNC_RIOZIO_STALL 0x8040 /* there's a RIO/ZIO entry that hasn't been serviced */ 289 #define ASYNC_RIO32_2_2200 0x8042 /* same as ASYNC_RIO32_2, but for 2100/2200 */ 290 #define ASYNC_RCV_ERR 0x8048 291 /* 292 * 2.01.31 2200 Only. Need Bit 13 in Mailbox 1 for Set Firmware Options 293 * mailbox command to enable this. 294 */ 295 #define ASYNC_QFULL_SENT 0x8049 296 #define ASYNC_RJT_SENT 0x8049 /* 24XX only */ 297 #define ASYNC_SEL_CLASS2_P_RJT_SENT 0x804f 298 #define ASYNC_FW_RESTART_COMPLETE 0x8060 299 #define ASYNC_TEMPERATURE_ALERT 0x8070 300 #define ASYNC_INTER_DRIVER_COMP 0x8100 /* FCoE only */ 301 #define ASYNC_INTER_DRIVER_NOTIFY 0x8101 /* FCoE only */ 302 #define ASYNC_INTER_DRIVER_TIME_EXT 0x8102 /* FCoE only */ 303 #define ASYNC_TRANSCEIVER_INSERTION 0x8130 304 #define ASYNC_TRANSCEIVER_REMOVAL 0x8131 305 #define ASYNC_NIC_FW_STATE_CHANGE 0x8200 /* FCoE only */ 306 #define ASYNC_AUTOLOAD_FW_COMPLETE 0x8400 307 #define ASYNC_AUTOLOAD_FW_FAILURE 0x8401 308 309 /* 310 * Firmware Options. There are a lot of them. 311 * 312 * IFCOPTN - ISP Fibre Channel Option Word N 313 */ 314 #define IFCOPT1_EQFQASYNC (1 << 13) /* enable QFULL notification */ 315 #define IFCOPT1_EAABSRCVD (1 << 12) 316 #define IFCOPT1_RJTASYNC (1 << 11) /* enable 8018 notification */ 317 #define IFCOPT1_ENAPURE (1 << 10) 318 #define IFCOPT1_ENA8017 (1 << 7) 319 #define IFCOPT1_DISGPIO67 (1 << 6) 320 #define IFCOPT1_LIPLOSSIMM (1 << 5) 321 #define IFCOPT1_DISF7SWTCH (1 << 4) 322 #define IFCOPT1_CTIO_RETRY (1 << 3) 323 #define IFCOPT1_LIPASYNC (1 << 1) 324 #define IFCOPT1_LIPF8 (1 << 0) 325 326 #define IFCOPT2_LOOPBACK (1 << 1) 327 #define IFCOPT2_ATIO3_ONLY (1 << 0) 328 329 #define IFCOPT3_NOPRLI (1 << 4) /* disable automatic sending of PRLI on local loops */ 330 #define IFCOPT3_RNDASYNC (1 << 1) 331 332 /* 333 * All IOCB Queue entries are this size 334 */ 335 #define QENTRY_LEN 64 336 337 /* 338 * Command Structure Definitions 339 */ 340 341 typedef struct { 342 uint32_t ds_base; 343 uint32_t ds_count; 344 } ispds_t; 345 346 typedef struct { 347 uint32_t ds_base; 348 uint32_t ds_basehi; 349 uint32_t ds_count; 350 } ispds64_t; 351 352 #define DSTYPE_32BIT 0 353 #define DSTYPE_64BIT 1 354 typedef struct { 355 uint16_t ds_type; /* 0-> ispds_t, 1-> ispds64_t */ 356 uint32_t ds_segment; /* unused */ 357 uint32_t ds_base; /* 32 bit address of DSD list */ 358 } ispdslist_t; 359 360 361 typedef struct { 362 uint8_t rqs_entry_type; 363 uint8_t rqs_entry_count; 364 uint8_t rqs_seqno; 365 uint8_t rqs_flags; 366 } isphdr_t; 367 368 /* RQS Flag definitions */ 369 #define RQSFLAG_CONTINUATION 0x01 370 #define RQSFLAG_FULL 0x02 371 #define RQSFLAG_BADHEADER 0x04 372 #define RQSFLAG_BADPACKET 0x08 373 #define RQSFLAG_BADCOUNT 0x10 374 #define RQSFLAG_BADORDER 0x20 375 #define RQSFLAG_MASK 0x3f 376 377 /* RQS entry_type definitions */ 378 #define RQSTYPE_REQUEST 0x01 379 #define RQSTYPE_DATASEG 0x02 380 #define RQSTYPE_RESPONSE 0x03 381 #define RQSTYPE_MARKER 0x04 382 #define RQSTYPE_CMDONLY 0x05 383 #define RQSTYPE_ATIO 0x06 /* Target Mode */ 384 #define RQSTYPE_CTIO 0x07 /* Target Mode */ 385 #define RQSTYPE_SCAM 0x08 386 #define RQSTYPE_A64 0x09 387 #define RQSTYPE_A64_CONT 0x0a 388 #define RQSTYPE_ENABLE_LUN 0x0b /* Target Mode */ 389 #define RQSTYPE_MODIFY_LUN 0x0c /* Target Mode */ 390 #define RQSTYPE_NOTIFY 0x0d /* Target Mode */ 391 #define RQSTYPE_NOTIFY_ACK 0x0e /* Target Mode */ 392 #define RQSTYPE_CTIO1 0x0f /* Target Mode */ 393 #define RQSTYPE_STATUS_CONT 0x10 394 #define RQSTYPE_T2RQS 0x11 395 #define RQSTYPE_CTIO7 0x12 396 #define RQSTYPE_IP_XMIT 0x13 397 #define RQSTYPE_TSK_MGMT 0x14 398 #define RQSTYPE_T4RQS 0x15 399 #define RQSTYPE_ATIO2 0x16 /* Target Mode */ 400 #define RQSTYPE_CTIO2 0x17 /* Target Mode */ 401 #define RQSTYPE_T7RQS 0x18 402 #define RQSTYPE_T3RQS 0x19 403 #define RQSTYPE_IP_XMIT_64 0x1b 404 #define RQSTYPE_CTIO4 0x1e /* Target Mode */ 405 #define RQSTYPE_CTIO3 0x1f /* Target Mode */ 406 #define RQSTYPE_RIO1 0x21 407 #define RQSTYPE_RIO2 0x22 408 #define RQSTYPE_IP_RECV 0x23 409 #define RQSTYPE_IP_RECV_CONT 0x24 410 #define RQSTYPE_CT_PASSTHRU 0x29 411 #define RQSTYPE_MS_PASSTHRU 0x29 412 #define RQSTYPE_VP_CTRL 0x30 /* 24XX only */ 413 #define RQSTYPE_VP_MODIFY 0x31 /* 24XX only */ 414 #define RQSTYPE_RPT_ID_ACQ 0x32 /* 24XX only */ 415 #define RQSTYPE_ABORT_IO 0x33 416 #define RQSTYPE_T6RQS 0x48 417 #define RQSTYPE_LOGIN 0x52 418 #define RQSTYPE_ABTS_RCVD 0x54 /* 24XX only */ 419 #define RQSTYPE_ABTS_RSP 0x55 /* 24XX only */ 420 421 422 #define ISP_RQDSEG 4 423 typedef struct { 424 isphdr_t req_header; 425 uint32_t req_handle; 426 uint8_t req_lun_trn; 427 uint8_t req_target; 428 uint16_t req_cdblen; 429 uint16_t req_flags; 430 uint16_t req_reserved; 431 uint16_t req_time; 432 uint16_t req_seg_count; 433 uint8_t req_cdb[12]; 434 ispds_t req_dataseg[ISP_RQDSEG]; 435 } ispreq_t; 436 #define ISP_RQDSEG_A64 2 437 438 typedef struct { 439 isphdr_t mrk_header; 440 uint32_t mrk_handle; 441 uint8_t mrk_reserved0; 442 uint8_t mrk_target; 443 uint16_t mrk_modifier; 444 uint16_t mrk_flags; 445 uint16_t mrk_lun; 446 uint8_t mrk_reserved1[48]; 447 } isp_marker_t; 448 449 typedef struct { 450 isphdr_t mrk_header; 451 uint32_t mrk_handle; 452 uint16_t mrk_nphdl; 453 uint8_t mrk_modifier; 454 uint8_t mrk_reserved0; 455 uint8_t mrk_reserved1; 456 uint8_t mrk_vphdl; 457 uint16_t mrk_reserved2; 458 uint8_t mrk_lun[8]; 459 uint8_t mrk_reserved3[40]; 460 } isp_marker_24xx_t; 461 462 463 #define SYNC_DEVICE 0 464 #define SYNC_TARGET 1 465 #define SYNC_ALL 2 466 #define SYNC_LIP 3 467 468 #define ISP_RQDSEG_T2 3 469 typedef struct { 470 isphdr_t req_header; 471 uint32_t req_handle; 472 uint8_t req_lun_trn; 473 uint8_t req_target; 474 uint16_t req_scclun; 475 uint16_t req_flags; 476 uint8_t req_crn; 477 uint8_t req_reserved; 478 uint16_t req_time; 479 uint16_t req_seg_count; 480 uint8_t req_cdb[16]; 481 uint32_t req_totalcnt; 482 ispds_t req_dataseg[ISP_RQDSEG_T2]; 483 } ispreqt2_t; 484 485 typedef struct { 486 isphdr_t req_header; 487 uint32_t req_handle; 488 uint16_t req_target; 489 uint16_t req_scclun; 490 uint16_t req_flags; 491 uint8_t req_crn; 492 uint8_t req_reserved; 493 uint16_t req_time; 494 uint16_t req_seg_count; 495 uint8_t req_cdb[16]; 496 uint32_t req_totalcnt; 497 ispds_t req_dataseg[ISP_RQDSEG_T2]; 498 } ispreqt2e_t; 499 500 #define ISP_RQDSEG_T3 2 501 typedef struct { 502 isphdr_t req_header; 503 uint32_t req_handle; 504 uint8_t req_lun_trn; 505 uint8_t req_target; 506 uint16_t req_scclun; 507 uint16_t req_flags; 508 uint8_t req_crn; 509 uint8_t req_reserved; 510 uint16_t req_time; 511 uint16_t req_seg_count; 512 uint8_t req_cdb[16]; 513 uint32_t req_totalcnt; 514 ispds64_t req_dataseg[ISP_RQDSEG_T3]; 515 } ispreqt3_t; 516 #define ispreq64_t ispreqt3_t /* same as.... */ 517 518 typedef struct { 519 isphdr_t req_header; 520 uint32_t req_handle; 521 uint16_t req_target; 522 uint16_t req_scclun; 523 uint16_t req_flags; 524 uint8_t req_crn; 525 uint8_t req_reserved; 526 uint16_t req_time; 527 uint16_t req_seg_count; 528 uint8_t req_cdb[16]; 529 uint32_t req_totalcnt; 530 ispds64_t req_dataseg[ISP_RQDSEG_T3]; 531 } ispreqt3e_t; 532 533 /* req_flag values */ 534 #define REQFLAG_NODISCON 0x0001 535 #define REQFLAG_HTAG 0x0002 536 #define REQFLAG_OTAG 0x0004 537 #define REQFLAG_STAG 0x0008 538 #define REQFLAG_TARGET_RTN 0x0010 539 540 #define REQFLAG_NODATA 0x0000 541 #define REQFLAG_DATA_IN 0x0020 542 #define REQFLAG_DATA_OUT 0x0040 543 #define REQFLAG_DATA_UNKNOWN 0x0060 544 545 #define REQFLAG_DISARQ 0x0100 546 #define REQFLAG_FRC_ASYNC 0x0200 547 #define REQFLAG_FRC_SYNC 0x0400 548 #define REQFLAG_FRC_WIDE 0x0800 549 #define REQFLAG_NOPARITY 0x1000 550 #define REQFLAG_STOPQ 0x2000 551 #define REQFLAG_XTRASNS 0x4000 552 #define REQFLAG_PRIORITY 0x8000 553 554 typedef struct { 555 isphdr_t req_header; 556 uint32_t req_handle; 557 uint8_t req_lun_trn; 558 uint8_t req_target; 559 uint16_t req_cdblen; 560 uint16_t req_flags; 561 uint16_t req_reserved; 562 uint16_t req_time; 563 uint16_t req_seg_count; 564 uint8_t req_cdb[44]; 565 } ispextreq_t; 566 567 568 /* 569 * ISP24XX structures 570 */ 571 typedef struct { 572 isphdr_t req_header; 573 uint32_t req_handle; 574 uint16_t req_nphdl; 575 uint16_t req_time; 576 uint16_t req_seg_count; 577 uint16_t req_reserved; 578 uint8_t req_lun[8]; 579 uint8_t req_alen_datadir; 580 uint8_t req_task_management; 581 uint8_t req_task_attribute; 582 uint8_t req_crn; 583 uint8_t req_cdb[16]; 584 uint32_t req_dl; 585 uint16_t req_tidlo; 586 uint8_t req_tidhi; 587 uint8_t req_vpidx; 588 ispds64_t req_dataseg; 589 } ispreqt7_t; 590 591 /* Task Management Request Function */ 592 typedef struct { 593 isphdr_t tmf_header; 594 uint32_t tmf_handle; 595 uint16_t tmf_nphdl; 596 uint8_t tmf_reserved0[2]; 597 uint16_t tmf_delay; 598 uint16_t tmf_timeout; 599 uint8_t tmf_lun[8]; 600 uint32_t tmf_flags; 601 uint8_t tmf_reserved1[20]; 602 uint16_t tmf_tidlo; 603 uint8_t tmf_tidhi; 604 uint8_t tmf_vpidx; 605 uint8_t tmf_reserved2[12]; 606 } isp24xx_tmf_t; 607 608 #define ISP24XX_TMF_NOSEND 0x80000000 609 610 #define ISP24XX_TMF_LUN_RESET 0x00000010 611 #define ISP24XX_TMF_ABORT_TASK_SET 0x00000008 612 #define ISP24XX_TMF_CLEAR_TASK_SET 0x00000004 613 #define ISP24XX_TMF_TARGET_RESET 0x00000002 614 #define ISP24XX_TMF_CLEAR_ACA 0x00000001 615 616 /* I/O Abort Structure */ 617 typedef struct { 618 isphdr_t abrt_header; 619 uint32_t abrt_handle; 620 uint16_t abrt_nphdl; 621 uint16_t abrt_options; 622 uint32_t abrt_cmd_handle; 623 uint16_t abrt_queue_number; 624 uint8_t abrt_reserved[30]; 625 uint16_t abrt_tidlo; 626 uint8_t abrt_tidhi; 627 uint8_t abrt_vpidx; 628 uint8_t abrt_reserved1[12]; 629 } isp24xx_abrt_t; 630 631 #define ISP24XX_ABRT_NOSEND 0x01 /* don't actually send ABTS */ 632 #define ISP24XX_ABRT_OKAY 0x00 /* in nphdl on return */ 633 #define ISP24XX_ABRT_ENXIO 0x31 /* in nphdl on return */ 634 635 #define ISP_CDSEG 7 636 typedef struct { 637 isphdr_t req_header; 638 uint32_t req_reserved; 639 ispds_t req_dataseg[ISP_CDSEG]; 640 } ispcontreq_t; 641 642 #define ISP_CDSEG64 5 643 typedef struct { 644 isphdr_t req_header; 645 ispds64_t req_dataseg[ISP_CDSEG64]; 646 } ispcontreq64_t; 647 648 typedef struct { 649 isphdr_t req_header; 650 uint32_t req_handle; 651 uint16_t req_scsi_status; 652 uint16_t req_completion_status; 653 uint16_t req_state_flags; 654 uint16_t req_status_flags; 655 uint16_t req_time; 656 #define req_response_len req_time /* FC only */ 657 uint16_t req_sense_len; 658 uint32_t req_resid; 659 uint8_t req_response[8]; /* FC only */ 660 uint8_t req_sense_data[32]; 661 } ispstatusreq_t; 662 663 /* 664 * Status Continuation 665 */ 666 typedef struct { 667 isphdr_t req_header; 668 uint8_t req_sense_data[60]; 669 } ispstatus_cont_t; 670 671 /* 672 * 24XX Type 0 status 673 */ 674 typedef struct { 675 isphdr_t req_header; 676 uint32_t req_handle; 677 uint16_t req_completion_status; 678 uint16_t req_oxid; 679 uint32_t req_resid; 680 uint16_t req_reserved0; 681 uint16_t req_state_flags; 682 uint16_t req_retry_delay; /* aka Status Qualifier */ 683 uint16_t req_scsi_status; 684 uint32_t req_fcp_residual; 685 uint32_t req_sense_len; 686 uint32_t req_response_len; 687 uint8_t req_rsp_sense[28]; 688 } isp24xx_statusreq_t; 689 690 /* 691 * For Qlogic 2X00, the high order byte of SCSI status has 692 * additional meaning. 693 */ 694 #define RQCS_CR 0x1000 /* Confirmation Request */ 695 #define RQCS_RU 0x0800 /* Residual Under */ 696 #define RQCS_RO 0x0400 /* Residual Over */ 697 #define RQCS_RESID (RQCS_RU|RQCS_RO) 698 #define RQCS_SV 0x0200 /* Sense Length Valid */ 699 #define RQCS_RV 0x0100 /* FCP Response Length Valid */ 700 701 /* 702 * CT Passthru IOCB 703 */ 704 typedef struct { 705 isphdr_t ctp_header; 706 uint32_t ctp_handle; 707 uint16_t ctp_status; 708 uint16_t ctp_nphdl; /* n-port handle */ 709 uint16_t ctp_cmd_cnt; /* Command DSD count */ 710 uint8_t ctp_vpidx; 711 uint8_t ctp_reserved0; 712 uint16_t ctp_time; 713 uint16_t ctp_reserved1; 714 uint16_t ctp_rsp_cnt; /* Response DSD count */ 715 uint16_t ctp_reserved2[5]; 716 uint32_t ctp_rsp_bcnt; /* Response byte count */ 717 uint32_t ctp_cmd_bcnt; /* Command byte count */ 718 ispds64_t ctp_dataseg[2]; 719 } isp_ct_pt_t; 720 721 /* 722 * MS Passthru IOCB 723 */ 724 typedef struct { 725 isphdr_t ms_header; 726 uint32_t ms_handle; 727 uint16_t ms_nphdl; /* handle in high byte for !2k f/w */ 728 uint16_t ms_status; 729 uint16_t ms_flags; 730 uint16_t ms_reserved1; /* low 8 bits */ 731 uint16_t ms_time; 732 uint16_t ms_cmd_cnt; /* Command DSD count */ 733 uint16_t ms_tot_cnt; /* Total DSD Count */ 734 uint8_t ms_type; /* MS type */ 735 uint8_t ms_r_ctl; /* R_CTL */ 736 uint16_t ms_rxid; /* RX_ID */ 737 uint16_t ms_reserved2; 738 uint32_t ms_handle2; 739 uint32_t ms_rsp_bcnt; /* Response byte count */ 740 uint32_t ms_cmd_bcnt; /* Command byte count */ 741 ispds64_t ms_dataseg[2]; 742 } isp_ms_t; 743 744 /* 745 * Completion Status Codes. 746 */ 747 #define RQCS_COMPLETE 0x0000 748 #define RQCS_DMA_ERROR 0x0002 749 #define RQCS_RESET_OCCURRED 0x0004 750 #define RQCS_ABORTED 0x0005 751 #define RQCS_TIMEOUT 0x0006 752 #define RQCS_DATA_OVERRUN 0x0007 753 #define RQCS_DATA_UNDERRUN 0x0015 754 #define RQCS_QUEUE_FULL 0x001C 755 756 /* 1X00 Only Completion Codes */ 757 #define RQCS_INCOMPLETE 0x0001 758 #define RQCS_TRANSPORT_ERROR 0x0003 759 #define RQCS_COMMAND_OVERRUN 0x0008 760 #define RQCS_STATUS_OVERRUN 0x0009 761 #define RQCS_BAD_MESSAGE 0x000a 762 #define RQCS_NO_MESSAGE_OUT 0x000b 763 #define RQCS_EXT_ID_FAILED 0x000c 764 #define RQCS_IDE_MSG_FAILED 0x000d 765 #define RQCS_ABORT_MSG_FAILED 0x000e 766 #define RQCS_REJECT_MSG_FAILED 0x000f 767 #define RQCS_NOP_MSG_FAILED 0x0010 768 #define RQCS_PARITY_ERROR_MSG_FAILED 0x0011 769 #define RQCS_DEVICE_RESET_MSG_FAILED 0x0012 770 #define RQCS_ID_MSG_FAILED 0x0013 771 #define RQCS_UNEXP_BUS_FREE 0x0014 772 #define RQCS_XACT_ERR1 0x0018 773 #define RQCS_XACT_ERR2 0x0019 774 #define RQCS_XACT_ERR3 0x001A 775 #define RQCS_BAD_ENTRY 0x001B 776 #define RQCS_PHASE_SKIPPED 0x001D 777 #define RQCS_ARQS_FAILED 0x001E 778 #define RQCS_WIDE_FAILED 0x001F 779 #define RQCS_SYNCXFER_FAILED 0x0020 780 #define RQCS_LVD_BUSERR 0x0021 781 782 /* 2X00 Only Completion Codes */ 783 #define RQCS_PORT_UNAVAILABLE 0x0028 784 #define RQCS_PORT_LOGGED_OUT 0x0029 785 #define RQCS_PORT_CHANGED 0x002A 786 #define RQCS_PORT_BUSY 0x002B 787 788 /* 24XX Only Completion Codes */ 789 #define RQCS_24XX_DRE 0x0011 /* data reassembly error */ 790 #define RQCS_24XX_TABORT 0x0013 /* aborted by target */ 791 #define RQCS_24XX_ENOMEM 0x002C /* f/w resource unavailable */ 792 #define RQCS_24XX_TMO 0x0030 /* task management overrun */ 793 794 795 /* 796 * 1X00 specific State Flags 797 */ 798 #define RQSF_GOT_BUS 0x0100 799 #define RQSF_GOT_TARGET 0x0200 800 #define RQSF_SENT_CDB 0x0400 801 #define RQSF_XFRD_DATA 0x0800 802 #define RQSF_GOT_STATUS 0x1000 803 #define RQSF_GOT_SENSE 0x2000 804 #define RQSF_XFER_COMPLETE 0x4000 805 806 /* 807 * 2X00 specific State Flags 808 * (same as 1X00 except RQSF_GOT_BUS/RQSF_GOT_TARGET are not available) 809 */ 810 #define RQSF_DATA_IN 0x0020 811 #define RQSF_DATA_OUT 0x0040 812 #define RQSF_STAG 0x0008 813 #define RQSF_OTAG 0x0004 814 #define RQSF_HTAG 0x0002 815 /* 816 * 1X00 Status Flags 817 */ 818 #define RQSTF_DISCONNECT 0x0001 819 #define RQSTF_SYNCHRONOUS 0x0002 820 #define RQSTF_PARITY_ERROR 0x0004 821 #define RQSTF_BUS_RESET 0x0008 822 #define RQSTF_DEVICE_RESET 0x0010 823 #define RQSTF_ABORTED 0x0020 824 #define RQSTF_TIMEOUT 0x0040 825 #define RQSTF_NEGOTIATION 0x0080 826 827 /* 828 * 2X00 specific state flags 829 */ 830 /* RQSF_SENT_CDB */ 831 /* RQSF_XFRD_DATA */ 832 /* RQSF_GOT_STATUS */ 833 /* RQSF_XFER_COMPLETE */ 834 835 /* 836 * 2X00 specific status flags 837 */ 838 /* RQSTF_ABORTED */ 839 /* RQSTF_TIMEOUT */ 840 #define RQSTF_DMA_ERROR 0x0080 841 #define RQSTF_LOGOUT 0x2000 842 843 /* 844 * Miscellaneous 845 */ 846 #ifndef ISP_EXEC_THROTTLE 847 #define ISP_EXEC_THROTTLE 16 848 #endif 849 850 /* 851 * About Firmware returns an 'attribute' word in mailbox 6. 852 * These attributes are for 2200 and 2300. 853 */ 854 #define ISP_FW_ATTR_TMODE 0x0001 855 #define ISP_FW_ATTR_SCCLUN 0x0002 856 #define ISP_FW_ATTR_FABRIC 0x0004 857 #define ISP_FW_ATTR_CLASS2 0x0008 858 #define ISP_FW_ATTR_FCTAPE 0x0010 859 #define ISP_FW_ATTR_IP 0x0020 860 #define ISP_FW_ATTR_VI 0x0040 861 #define ISP_FW_ATTR_VI_SOLARIS 0x0080 862 #define ISP_FW_ATTR_2KLOGINS 0x0100 /* just a guess... */ 863 864 /* and these are for the 2400 */ 865 #define ISP2400_FW_ATTR_CLASS2 0x0001 866 #define ISP2400_FW_ATTR_IP 0x0002 867 #define ISP2400_FW_ATTR_MULTIID 0x0004 868 #define ISP2400_FW_ATTR_SB2 0x0008 869 #define ISP2400_FW_ATTR_T10CRC 0x0010 870 #define ISP2400_FW_ATTR_VI 0x0020 871 #define ISP2400_FW_ATTR_MQ 0x0040 872 #define ISP2400_FW_ATTR_MSIX 0x0080 873 #define ISP2400_FW_ATTR_FCOE 0x0800 874 #define ISP2400_FW_ATTR_VP0 0x1000 875 #define ISP2400_FW_ATTR_EXPFW 0x2000 876 #define ISP2400_FW_ATTR_HOTFW 0x4000 877 #define ISP2400_FW_ATTR_EXTNDED 0x8000 878 #define ISP2400_FW_ATTR_EXTVP 0x00010000 879 #define ISP2400_FW_ATTR_VN2VN 0x00040000 880 #define ISP2400_FW_ATTR_EXMOFF 0x00080000 881 #define ISP2400_FW_ATTR_NPMOFF 0x00100000 882 #define ISP2400_FW_ATTR_DIFCHOP 0x00400000 883 #define ISP2400_FW_ATTR_SRIOV 0x02000000 884 #define ISP2400_FW_ATTR_ASICTMP 0x0200000000 885 #define ISP2400_FW_ATTR_ATIOMQ 0x0400000000 886 887 /* 888 * These are either manifestly true or are dependent on f/w attributes 889 */ 890 #define ISP_CAP_TMODE(isp) \ 891 (IS_24XX(isp)? 1 : (isp->isp_fwattr & ISP_FW_ATTR_TMODE)) 892 #define ISP_CAP_SCCFW(isp) \ 893 (IS_24XX(isp)? 1 : (isp->isp_fwattr & ISP_FW_ATTR_SCCLUN)) 894 #define ISP_CAP_2KLOGIN(isp) \ 895 (IS_24XX(isp)? 1 : (isp->isp_fwattr & ISP_FW_ATTR_2KLOGINS)) 896 897 /* 898 * This is only true for 24XX cards with this f/w attribute 899 */ 900 #define ISP_CAP_MULTI_ID(isp) \ 901 (IS_24XX(isp)? (isp->isp_fwattr & ISP2400_FW_ATTR_MULTIID) : 0) 902 #define ISP_GET_VPIDX(isp, tag) \ 903 (ISP_CAP_MULTI_ID(isp) ? tag : 0) 904 #define ISP_CAP_MSIX(isp) \ 905 (IS_24XX(isp)? (isp->isp_fwattr & ISP2400_FW_ATTR_MSIX) : 0) 906 #define ISP_CAP_VP0(isp) \ 907 (IS_24XX(isp)? (isp->isp_fwattr & ISP2400_FW_ATTR_VP0) : 0) 908 909 /* 910 * This is true manifestly or is dependent on a f/w attribute 911 * but may or may not actually be *enabled*. In any case, it 912 * is enabled on a per-channel basis. 913 */ 914 #define ISP_CAP_FCTAPE(isp) \ 915 (IS_24XX(isp)? 1 : (isp->isp_fwattr & ISP_FW_ATTR_FCTAPE)) 916 917 #define ISP_FCTAPE_ENABLED(isp, chan) \ 918 (IS_24XX(isp)? (FCPARAM(isp, chan)->isp_xfwoptions & ICB2400_OPT2_FCTAPE) != 0 : (FCPARAM(isp, chan)->isp_xfwoptions & ICBXOPT_FCTAPE) != 0) 919 920 /* 921 * Reduced Interrupt Operation Response Queue Entries 922 */ 923 924 typedef struct { 925 isphdr_t req_header; 926 uint32_t req_handles[15]; 927 } isp_rio1_t; 928 929 typedef struct { 930 isphdr_t req_header; 931 uint16_t req_handles[30]; 932 } isp_rio2_t; 933 934 /* 935 * FC (ISP2100/ISP2200/ISP2300/ISP2400) specific data structures 936 */ 937 938 /* 939 * Initialization Control Block 940 * 941 * Version One (prime) format. 942 */ 943 typedef struct { 944 uint8_t icb_version; 945 uint8_t icb_reserved0; 946 uint16_t icb_fwoptions; 947 uint16_t icb_maxfrmlen; 948 uint16_t icb_maxalloc; 949 uint16_t icb_execthrottle; 950 uint8_t icb_retry_count; 951 uint8_t icb_retry_delay; 952 uint8_t icb_portname[8]; 953 uint16_t icb_hardaddr; 954 uint8_t icb_iqdevtype; 955 uint8_t icb_logintime; 956 uint8_t icb_nodename[8]; 957 uint16_t icb_rqstout; 958 uint16_t icb_rspnsin; 959 uint16_t icb_rqstqlen; 960 uint16_t icb_rsltqlen; 961 uint16_t icb_rqstaddr[4]; 962 uint16_t icb_respaddr[4]; 963 uint16_t icb_lunenables; 964 uint8_t icb_ccnt; 965 uint8_t icb_icnt; 966 uint16_t icb_lunetimeout; 967 uint16_t icb_reserved1; 968 uint16_t icb_xfwoptions; 969 uint8_t icb_racctimer; 970 uint8_t icb_idelaytimer; 971 uint16_t icb_zfwoptions; 972 uint16_t icb_reserved2[13]; 973 } isp_icb_t; 974 975 #define ICB_VERSION1 1 976 977 #define ICBOPT_EXTENDED 0x8000 978 #define ICBOPT_BOTH_WWNS 0x4000 979 #define ICBOPT_FULL_LOGIN 0x2000 980 #define ICBOPT_STOP_ON_QFULL 0x1000 /* 2200/2100 only */ 981 #define ICBOPT_PREV_ADDRESS 0x0800 982 #define ICBOPT_SRCHDOWN 0x0400 983 #define ICBOPT_NOLIP 0x0200 984 #define ICBOPT_PDBCHANGE_AE 0x0100 985 #define ICBOPT_TGT_TYPE 0x0080 986 #define ICBOPT_INI_ADISC 0x0040 987 #define ICBOPT_INI_DISABLE 0x0020 988 #define ICBOPT_TGT_ENABLE 0x0010 989 #define ICBOPT_FAST_POST 0x0008 990 #define ICBOPT_FULL_DUPLEX 0x0004 991 #define ICBOPT_FAIRNESS 0x0002 992 #define ICBOPT_HARD_ADDRESS 0x0001 993 994 #define ICBXOPT_NO_LOGOUT 0x8000 /* no logout on link failure */ 995 #define ICBXOPT_FCTAPE_CCQ 0x4000 /* FC-Tape Command Queueing */ 996 #define ICBXOPT_FCTAPE_CONFIRM 0x2000 997 #define ICBXOPT_FCTAPE 0x1000 998 #define ICBXOPT_CLASS2_ACK0 0x0200 999 #define ICBXOPT_CLASS2 0x0100 1000 #define ICBXOPT_NO_PLAY 0x0080 /* don't play if can't get hard addr */ 1001 #define ICBXOPT_TOPO_MASK 0x0070 1002 #define ICBXOPT_LOOP_ONLY 0x0000 1003 #define ICBXOPT_PTP_ONLY 0x0010 1004 #define ICBXOPT_LOOP_2_PTP 0x0020 1005 #define ICBXOPT_PTP_2_LOOP 0x0030 1006 /* 1007 * The lower 4 bits of the xfwoptions field are the OPERATION MODE bits. 1008 * RIO is not defined for the 23XX cards (just 2200) 1009 */ 1010 #define ICBXOPT_RIO_OFF 0 1011 #define ICBXOPT_RIO_16BIT 1 1012 #define ICBXOPT_RIO_32BIT 2 1013 #define ICBXOPT_RIO_16BIT_IOCB 3 1014 #define ICBXOPT_RIO_32BIT_IOCB 4 1015 #define ICBXOPT_ZIO 5 1016 #define ICBXOPT_TIMER_MASK 0x7 1017 1018 #define ICBZOPT_RATE_MASK 0xC000 1019 #define ICBZOPT_RATE_1GB 0x0000 1020 #define ICBZOPT_RATE_AUTO 0x8000 1021 #define ICBZOPT_RATE_2GB 0x4000 1022 #define ICBZOPT_50_OHM 0x2000 1023 #define ICBZOPT_NO_LOCAL_PLOGI 0x0080 1024 #define ICBZOPT_ENA_OOF 0x0040 /* out of order frame handling */ 1025 #define ICBZOPT_RSPSZ_MASK 0x0030 1026 #define ICBZOPT_RSPSZ_24 0x0000 1027 #define ICBZOPT_RSPSZ_12 0x0010 1028 #define ICBZOPT_RSPSZ_24A 0x0020 1029 #define ICBZOPT_RSPSZ_32 0x0030 1030 #define ICBZOPT_SOFTID 0x0002 1031 #define ICBZOPT_ENA_RDXFR_RDY 0x0001 1032 1033 /* 2400 F/W options */ 1034 #define ICB2400_OPT1_BOTH_WWNS 0x00004000 1035 #define ICB2400_OPT1_FULL_LOGIN 0x00002000 1036 #define ICB2400_OPT1_PREV_ADDRESS 0x00000800 1037 #define ICB2400_OPT1_SRCHDOWN 0x00000400 1038 #define ICB2400_OPT1_NOLIP 0x00000200 1039 #define ICB2400_OPT1_INI_DISABLE 0x00000020 1040 #define ICB2400_OPT1_TGT_ENABLE 0x00000010 1041 #define ICB2400_OPT1_FULL_DUPLEX 0x00000004 1042 #define ICB2400_OPT1_FAIRNESS 0x00000002 1043 #define ICB2400_OPT1_HARD_ADDRESS 0x00000001 1044 1045 #define ICB2400_OPT2_ENA_ATIOMQ 0x08000000 1046 #define ICB2400_OPT2_ENA_IHA 0x04000000 1047 #define ICB2400_OPT2_QOS 0x02000000 1048 #define ICB2400_OPT2_IOCBS 0x01000000 1049 #define ICB2400_OPT2_ENA_IHR 0x00400000 1050 #define ICB2400_OPT2_ENA_VMS 0x00200000 1051 #define ICB2400_OPT2_ENA_TA 0x00100000 1052 #define ICB2400_OPT2_TPRLIC 0x00004000 1053 #define ICB2400_OPT2_FCTAPE 0x00001000 1054 #define ICB2400_OPT2_FCSP 0x00000800 1055 #define ICB2400_OPT2_CLASS2_ACK0 0x00000200 1056 #define ICB2400_OPT2_CLASS2 0x00000100 1057 #define ICB2400_OPT2_NO_PLAY 0x00000080 1058 #define ICB2400_OPT2_TOPO_MASK 0x00000070 1059 #define ICB2400_OPT2_LOOP_ONLY 0x00000000 1060 #define ICB2400_OPT2_PTP_ONLY 0x00000010 1061 #define ICB2400_OPT2_LOOP_2_PTP 0x00000020 1062 #define ICB2400_OPT2_TIMER_MASK 0x0000000f 1063 #define ICB2400_OPT2_ZIO 0x00000005 1064 #define ICB2400_OPT2_ZIO1 0x00000006 1065 1066 #define ICB2400_OPT3_NO_CTXDIS 0x40000000 1067 #define ICB2400_OPT3_ENA_ETH_RESP 0x08000000 1068 #define ICB2400_OPT3_ENA_ETH_ATIO 0x04000000 1069 #define ICB2400_OPT3_ENA_MFCF 0x00020000 1070 #define ICB2400_OPT3_SKIP_4GB 0x00010000 1071 #define ICB2400_OPT3_RATE_MASK 0x0000E000 1072 #define ICB2400_OPT3_RATE_1GB 0x00000000 1073 #define ICB2400_OPT3_RATE_2GB 0x00002000 1074 #define ICB2400_OPT3_RATE_AUTO 0x00004000 1075 #define ICB2400_OPT3_RATE_4GB 0x00006000 1076 #define ICB2400_OPT3_RATE_8GB 0x00008000 1077 #define ICB2400_OPT3_RATE_16GB 0x0000A000 1078 #define ICB2400_OPT3_RATE_32GB 0x0000C000 1079 #define ICB2400_OPT3_ENA_OOF_XFRDY 0x00000200 1080 #define ICB2400_OPT3_NO_N2N_LOGI 0x00000100 1081 #define ICB2400_OPT3_NO_LOCAL_PLOGI 0x00000080 1082 #define ICB2400_OPT3_ENA_OOF 0x00000040 1083 /* note that a response size flag of zero is reserved! */ 1084 #define ICB2400_OPT3_RSPSZ_MASK 0x00000030 1085 #define ICB2400_OPT3_RSPSZ_12 0x00000010 1086 #define ICB2400_OPT3_RSPSZ_24 0x00000020 1087 #define ICB2400_OPT3_RSPSZ_32 0x00000030 1088 #define ICB2400_OPT3_SOFTID 0x00000002 1089 1090 #define ICB_MIN_FRMLEN 256 1091 #define ICB_MAX_FRMLEN 2112 1092 #define ICB_DFLT_FRMLEN 1024 1093 #define ICB_DFLT_ALLOC 256 1094 #define ICB_DFLT_THROTTLE 16 1095 #define ICB_DFLT_RDELAY 5 1096 #define ICB_DFLT_RCOUNT 3 1097 1098 #define ICB_LOGIN_TOV 10 1099 #define ICB_LUN_ENABLE_TOV 15 1100 1101 1102 /* 1103 * And somebody at QLogic had a great idea that you could just change 1104 * the structure *and* keep the version number the same as the other cards. 1105 */ 1106 typedef struct { 1107 uint16_t icb_version; 1108 uint16_t icb_reserved0; 1109 uint16_t icb_maxfrmlen; 1110 uint16_t icb_execthrottle; 1111 uint16_t icb_xchgcnt; 1112 uint16_t icb_hardaddr; 1113 uint8_t icb_portname[8]; 1114 uint8_t icb_nodename[8]; 1115 uint16_t icb_rspnsin; 1116 uint16_t icb_rqstout; 1117 uint16_t icb_retry_count; 1118 uint16_t icb_priout; 1119 uint16_t icb_rsltqlen; 1120 uint16_t icb_rqstqlen; 1121 uint16_t icb_ldn_nols; 1122 uint16_t icb_prqstqlen; 1123 uint16_t icb_rqstaddr[4]; 1124 uint16_t icb_respaddr[4]; 1125 uint16_t icb_priaddr[4]; 1126 uint16_t icb_msixresp; 1127 uint16_t icb_msixatio; 1128 uint16_t icb_reserved1[2]; 1129 uint16_t icb_atio_in; 1130 uint16_t icb_atioqlen; 1131 uint16_t icb_atioqaddr[4]; 1132 uint16_t icb_idelaytimer; 1133 uint16_t icb_logintime; 1134 uint32_t icb_fwoptions1; 1135 uint32_t icb_fwoptions2; 1136 uint32_t icb_fwoptions3; 1137 uint16_t icb_qos; 1138 uint16_t icb_reserved2[3]; 1139 uint16_t icb_enodemac[3]; 1140 uint16_t icb_disctime; 1141 uint16_t icb_reserved3[4]; 1142 } isp_icb_2400_t; 1143 1144 #define RQRSP_ADDR0015 0 1145 #define RQRSP_ADDR1631 1 1146 #define RQRSP_ADDR3247 2 1147 #define RQRSP_ADDR4863 3 1148 1149 1150 #define ICB_NNM0 7 1151 #define ICB_NNM1 6 1152 #define ICB_NNM2 5 1153 #define ICB_NNM3 4 1154 #define ICB_NNM4 3 1155 #define ICB_NNM5 2 1156 #define ICB_NNM6 1 1157 #define ICB_NNM7 0 1158 1159 #define MAKE_NODE_NAME_FROM_WWN(array, wwn) \ 1160 array[ICB_NNM0] = (uint8_t) ((wwn >> 0) & 0xff), \ 1161 array[ICB_NNM1] = (uint8_t) ((wwn >> 8) & 0xff), \ 1162 array[ICB_NNM2] = (uint8_t) ((wwn >> 16) & 0xff), \ 1163 array[ICB_NNM3] = (uint8_t) ((wwn >> 24) & 0xff), \ 1164 array[ICB_NNM4] = (uint8_t) ((wwn >> 32) & 0xff), \ 1165 array[ICB_NNM5] = (uint8_t) ((wwn >> 40) & 0xff), \ 1166 array[ICB_NNM6] = (uint8_t) ((wwn >> 48) & 0xff), \ 1167 array[ICB_NNM7] = (uint8_t) ((wwn >> 56) & 0xff) 1168 1169 #define MAKE_WWN_FROM_NODE_NAME(wwn, array) \ 1170 wwn = ((uint64_t) array[ICB_NNM0]) | \ 1171 ((uint64_t) array[ICB_NNM1] << 8) | \ 1172 ((uint64_t) array[ICB_NNM2] << 16) | \ 1173 ((uint64_t) array[ICB_NNM3] << 24) | \ 1174 ((uint64_t) array[ICB_NNM4] << 32) | \ 1175 ((uint64_t) array[ICB_NNM5] << 40) | \ 1176 ((uint64_t) array[ICB_NNM6] << 48) | \ 1177 ((uint64_t) array[ICB_NNM7] << 56) 1178 1179 1180 /* 1181 * For MULTI_ID firmware, this describes a 1182 * virtual port entity for getting status. 1183 */ 1184 typedef struct { 1185 uint16_t vp_port_status; 1186 uint8_t vp_port_options; 1187 uint8_t vp_port_loopid; 1188 uint8_t vp_port_portname[8]; 1189 uint8_t vp_port_nodename[8]; 1190 uint16_t vp_port_portid_lo; /* not present when trailing icb */ 1191 uint16_t vp_port_portid_hi; /* not present when trailing icb */ 1192 } vp_port_info_t; 1193 1194 #define ICB2400_VPOPT_ENA_SNSLOGIN 0x00000040 /* Enable SNS Login and SCR for Virtual Ports */ 1195 #define ICB2400_VPOPT_TGT_DISABLE 0x00000020 /* Target Mode Disabled */ 1196 #define ICB2400_VPOPT_INI_ENABLE 0x00000010 /* Initiator Mode Enabled */ 1197 #define ICB2400_VPOPT_ENABLED 0x00000008 /* VP Enabled */ 1198 #define ICB2400_VPOPT_NOPLAY 0x00000004 /* ID Not Acquired */ 1199 #define ICB2400_VPOPT_PREV_ADDRESS 0x00000002 /* Previously Assigned ID */ 1200 #define ICB2400_VPOPT_HARD_ADDRESS 0x00000001 /* Hard Assigned ID */ 1201 1202 #define ICB2400_VPOPT_WRITE_SIZE 20 1203 1204 /* 1205 * For MULTI_ID firmware, we append this structure 1206 * to the isp_icb_2400_t above, followed by a list 1207 * structures that are *most* of the vp_port_info_t. 1208 */ 1209 typedef struct { 1210 uint16_t vp_count; 1211 uint16_t vp_global_options; 1212 } isp_icb_2400_vpinfo_t; 1213 1214 #define ICB2400_VPINFO_OFF 0x80 /* offset from start of ICB */ 1215 #define ICB2400_VPINFO_PORT_OFF(chan) \ 1216 (ICB2400_VPINFO_OFF + \ 1217 sizeof (isp_icb_2400_vpinfo_t) + ((chan) * ICB2400_VPOPT_WRITE_SIZE)) 1218 1219 #define ICB2400_VPGOPT_FCA 0x01 /* Assume Clean Address bit in FLOGI ACC set (works only in static configurations) */ 1220 #define ICB2400_VPGOPT_MID_DISABLE 0x02 /* when set, connection mode2 will work with NPIV-capable switched */ 1221 #define ICB2400_VPGOPT_VP0_DECOUPLE 0x04 /* Allow VP0 decoupling if firmware supports it */ 1222 #define ICB2400_VPGOPT_SUSP_FDISK 0x10 /* Suspend FDISC for Enabled VPs */ 1223 #define ICB2400_VPGOPT_GEN_RIDA 0x20 /* Generate RIDA if FLOGI Fails */ 1224 1225 typedef struct { 1226 isphdr_t vp_ctrl_hdr; 1227 uint32_t vp_ctrl_handle; 1228 uint16_t vp_ctrl_index_fail; 1229 uint16_t vp_ctrl_status; 1230 uint16_t vp_ctrl_command; 1231 uint16_t vp_ctrl_vp_count; 1232 uint16_t vp_ctrl_idmap[16]; 1233 uint16_t vp_ctrl_reserved[7]; 1234 uint16_t vp_ctrl_fcf_index; 1235 } vp_ctrl_info_t; 1236 1237 #define VP_CTRL_CMD_ENABLE_VP 0x00 1238 #define VP_CTRL_CMD_DISABLE_VP 0x08 1239 #define VP_CTRL_CMD_DISABLE_VP_REINIT_LINK 0x09 1240 #define VP_CTRL_CMD_DISABLE_VP_LOGO 0x0A 1241 #define VP_CTRL_CMD_DISABLE_VP_LOGO_ALL 0x0B 1242 1243 /* 1244 * We can use this structure for modifying either one or two VP ports after initialization 1245 */ 1246 typedef struct { 1247 isphdr_t vp_mod_hdr; 1248 uint32_t vp_mod_hdl; 1249 uint16_t vp_mod_reserved0; 1250 uint16_t vp_mod_status; 1251 uint8_t vp_mod_cmd; 1252 uint8_t vp_mod_cnt; 1253 uint8_t vp_mod_idx0; 1254 uint8_t vp_mod_idx1; 1255 struct { 1256 uint8_t options; 1257 uint8_t loopid; 1258 uint16_t reserved1; 1259 uint8_t wwpn[8]; 1260 uint8_t wwnn[8]; 1261 } vp_mod_ports[2]; 1262 uint8_t vp_mod_reserved2[8]; 1263 } vp_modify_t; 1264 1265 #define VP_STS_OK 0x00 1266 #define VP_STS_ERR 0x01 1267 #define VP_CNT_ERR 0x02 1268 #define VP_GEN_ERR 0x03 1269 #define VP_IDX_ERR 0x04 1270 #define VP_STS_BSY 0x05 1271 1272 #define VP_MODIFY 0x00 1273 #define VP_MODIFY_ENA 0x01 1274 #define VP_MODIFY_OPT 0x02 1275 #define VP_RESUME 0x03 1276 1277 /* 1278 * Port Data Base Element 1279 */ 1280 1281 typedef struct { 1282 uint16_t pdb_options; 1283 uint8_t pdb_mstate; 1284 uint8_t pdb_sstate; 1285 uint8_t pdb_hardaddr_bits[4]; 1286 uint8_t pdb_portid_bits[4]; 1287 uint8_t pdb_nodename[8]; 1288 uint8_t pdb_portname[8]; 1289 uint16_t pdb_execthrottle; 1290 uint16_t pdb_exec_count; 1291 uint8_t pdb_retry_count; 1292 uint8_t pdb_retry_delay; 1293 uint16_t pdb_resalloc; 1294 uint16_t pdb_curalloc; 1295 uint16_t pdb_qhead; 1296 uint16_t pdb_qtail; 1297 uint16_t pdb_tl_next; 1298 uint16_t pdb_tl_last; 1299 uint16_t pdb_features; /* PLOGI, Common Service */ 1300 uint16_t pdb_pconcurrnt; /* PLOGI, Common Service */ 1301 uint16_t pdb_roi; /* PLOGI, Common Service */ 1302 uint8_t pdb_target; 1303 uint8_t pdb_initiator; /* PLOGI, Class 3 Control Flags */ 1304 uint16_t pdb_rdsiz; /* PLOGI, Class 3 */ 1305 uint16_t pdb_ncseq; /* PLOGI, Class 3 */ 1306 uint16_t pdb_noseq; /* PLOGI, Class 3 */ 1307 uint16_t pdb_labrtflg; 1308 uint16_t pdb_lstopflg; 1309 uint16_t pdb_sqhead; 1310 uint16_t pdb_sqtail; 1311 uint16_t pdb_ptimer; 1312 uint16_t pdb_nxt_seqid; 1313 uint16_t pdb_fcount; 1314 uint16_t pdb_prli_len; 1315 uint16_t pdb_prli_svc0; 1316 uint16_t pdb_prli_svc3; 1317 uint16_t pdb_loopid; 1318 uint16_t pdb_il_ptr; 1319 uint16_t pdb_sl_ptr; 1320 } isp_pdb_21xx_t; 1321 1322 #define PDB_OPTIONS_XMITTING (1<<11) 1323 #define PDB_OPTIONS_LNKXMIT (1<<10) 1324 #define PDB_OPTIONS_ABORTED (1<<9) 1325 #define PDB_OPTIONS_ADISC (1<<1) 1326 1327 #define PDB_STATE_DISCOVERY 0 1328 #define PDB_STATE_WDISC_ACK 1 1329 #define PDB_STATE_PLOGI 2 1330 #define PDB_STATE_PLOGI_ACK 3 1331 #define PDB_STATE_PRLI 4 1332 #define PDB_STATE_PRLI_ACK 5 1333 #define PDB_STATE_LOGGED_IN 6 1334 #define PDB_STATE_PORT_UNAVAIL 7 1335 #define PDB_STATE_PRLO 8 1336 #define PDB_STATE_PRLO_ACK 9 1337 #define PDB_STATE_PLOGO 10 1338 #define PDB_STATE_PLOG_ACK 11 1339 1340 #define SVC3_ROLE_MASK 0x30 1341 #define SVC3_ROLE_SHIFT 4 1342 1343 #define BITS2WORD(x) ((x)[0] << 16 | (x)[3] << 8 | (x)[2]) 1344 #define BITS2WORD_24XX(x) ((x)[0] << 16 | (x)[1] << 8 | (x)[2]) 1345 1346 /* 1347 * Port Data Base Element- 24XX cards 1348 */ 1349 typedef struct { 1350 uint16_t pdb_flags; 1351 uint8_t pdb_curstate; 1352 uint8_t pdb_laststate; 1353 uint8_t pdb_hardaddr_bits[4]; 1354 uint8_t pdb_portid_bits[4]; 1355 #define pdb_nxt_seqid_2400 pdb_portid_bits[3] 1356 uint16_t pdb_retry_timer; 1357 uint16_t pdb_handle; 1358 uint16_t pdb_rcv_dsize; 1359 uint16_t pdb_reserved0; 1360 uint16_t pdb_prli_svc0; 1361 uint16_t pdb_prli_svc3; 1362 uint8_t pdb_portname[8]; 1363 uint8_t pdb_nodename[8]; 1364 uint8_t pdb_reserved1[24]; 1365 } isp_pdb_24xx_t; 1366 1367 #define PDB2400_TID_SUPPORTED 0x4000 1368 #define PDB2400_FC_TAPE 0x0080 1369 #define PDB2400_CLASS2_ACK0 0x0040 1370 #define PDB2400_FCP_CONF 0x0020 1371 #define PDB2400_CLASS2 0x0010 1372 #define PDB2400_ADDR_VALID 0x0002 1373 1374 #define PDB2400_STATE_PLOGI_PEND 0x03 1375 #define PDB2400_STATE_PLOGI_DONE 0x04 1376 #define PDB2400_STATE_PRLI_PEND 0x05 1377 #define PDB2400_STATE_LOGGED_IN 0x06 1378 #define PDB2400_STATE_PORT_UNAVAIL 0x07 1379 #define PDB2400_STATE_PRLO_PEND 0x09 1380 #define PDB2400_STATE_LOGO_PEND 0x0B 1381 1382 /* 1383 * Common elements from the above two structures that are actually useful to us. 1384 */ 1385 typedef struct { 1386 uint16_t handle; 1387 uint16_t prli_word3; 1388 uint32_t : 8, 1389 portid : 24; 1390 uint8_t portname[8]; 1391 uint8_t nodename[8]; 1392 } isp_pdb_t; 1393 1394 /* 1395 * Port/Node Name List Element 1396 */ 1397 typedef struct { 1398 uint8_t pnnle_name[8]; 1399 uint16_t pnnle_handle; 1400 uint16_t pnnle_reserved; 1401 } isp_pnnle_t; 1402 1403 #define PNNL_OPTIONS_NODE_NAMES (1<<0) 1404 #define PNNL_OPTIONS_PORT_DATA (1<<2) 1405 #define PNNL_OPTIONS_INITIATORS (1<<3) 1406 1407 /* 1408 * Port and N-Port Handle List Element 1409 */ 1410 typedef struct { 1411 uint16_t pnhle_port_id_lo; 1412 uint16_t pnhle_port_id_hi_handle; 1413 } isp_pnhle_21xx_t; 1414 1415 typedef struct { 1416 uint16_t pnhle_port_id_lo; 1417 uint16_t pnhle_port_id_hi; 1418 uint16_t pnhle_handle; 1419 } isp_pnhle_23xx_t; 1420 1421 typedef struct { 1422 uint16_t pnhle_port_id_lo; 1423 uint16_t pnhle_port_id_hi; 1424 uint16_t pnhle_handle; 1425 uint16_t pnhle_reserved; 1426 } isp_pnhle_24xx_t; 1427 1428 /* 1429 * Port Database Changed Async Event information for 24XX cards 1430 */ 1431 /* N-Port Handle */ 1432 #define PDB24XX_AE_GLOBAL 0xFFFF 1433 1434 /* Reason Codes */ 1435 #define PDB24XX_AE_OK 0x00 1436 #define PDB24XX_AE_IMPL_LOGO_1 0x01 1437 #define PDB24XX_AE_IMPL_LOGO_2 0x02 1438 #define PDB24XX_AE_IMPL_LOGO_3 0x03 1439 #define PDB24XX_AE_PLOGI_RCVD 0x04 1440 #define PDB24XX_AE_PLOGI_RJT 0x05 1441 #define PDB24XX_AE_PRLI_RCVD 0x06 1442 #define PDB24XX_AE_PRLI_RJT 0x07 1443 #define PDB24XX_AE_TPRLO 0x08 1444 #define PDB24XX_AE_TPRLO_RJT 0x09 1445 #define PDB24XX_AE_PRLO_RCVD 0x0a 1446 #define PDB24XX_AE_LOGO_RCVD 0x0b 1447 #define PDB24XX_AE_TOPO_CHG 0x0c 1448 #define PDB24XX_AE_NPORT_CHG 0x0d 1449 #define PDB24XX_AE_FLOGI_RJT 0x0e 1450 #define PDB24XX_AE_BAD_FANN 0x0f 1451 #define PDB24XX_AE_FLOGI_TIMO 0x10 1452 #define PDB24XX_AE_ABX_LOGO 0x11 1453 #define PDB24XX_AE_PLOGI_DONE 0x12 1454 #define PDB24XX_AE_PRLI_DONE 0x13 1455 #define PDB24XX_AE_OPN_1 0x14 1456 #define PDB24XX_AE_OPN_2 0x15 1457 #define PDB24XX_AE_TXERR 0x16 1458 #define PDB24XX_AE_FORCED_LOGO 0x17 1459 #define PDB24XX_AE_DISC_TIMO 0x18 1460 1461 /* 1462 * Genericized Port Login/Logout software structure 1463 */ 1464 typedef struct { 1465 uint16_t handle; 1466 uint16_t channel; 1467 uint32_t 1468 flags : 8, 1469 portid : 24; 1470 } isp_plcmd_t; 1471 /* the flags to use are those for PLOGX_FLG_* below */ 1472 1473 /* 1474 * ISP24XX- Login/Logout Port IOCB 1475 */ 1476 typedef struct { 1477 isphdr_t plogx_header; 1478 uint32_t plogx_handle; 1479 uint16_t plogx_status; 1480 uint16_t plogx_nphdl; 1481 uint16_t plogx_flags; 1482 uint16_t plogx_vphdl; /* low 8 bits */ 1483 uint16_t plogx_portlo; /* low 16 bits */ 1484 uint16_t plogx_rspsz_porthi; 1485 struct { 1486 uint16_t lo16; 1487 uint16_t hi16; 1488 } plogx_ioparm[11]; 1489 } isp_plogx_t; 1490 1491 #define PLOGX_STATUS_OK 0x00 1492 #define PLOGX_STATUS_UNAVAIL 0x28 1493 #define PLOGX_STATUS_LOGOUT 0x29 1494 #define PLOGX_STATUS_IOCBERR 0x31 1495 1496 #define PLOGX_IOCBERR_NOLINK 0x01 1497 #define PLOGX_IOCBERR_NOIOCB 0x02 1498 #define PLOGX_IOCBERR_NOXGHG 0x03 1499 #define PLOGX_IOCBERR_FAILED 0x04 /* further info in IOPARM 1 */ 1500 #define PLOGX_IOCBERR_NOFABRIC 0x05 1501 #define PLOGX_IOCBERR_NOTREADY 0x07 1502 #define PLOGX_IOCBERR_NOLOGIN 0x09 /* further info in IOPARM 1 */ 1503 #define PLOGX_IOCBERR_NOPCB 0x0a 1504 #define PLOGX_IOCBERR_REJECT 0x18 /* further info in IOPARM 1 */ 1505 #define PLOGX_IOCBERR_EINVAL 0x19 /* further info in IOPARM 1 */ 1506 #define PLOGX_IOCBERR_PORTUSED 0x1a /* further info in IOPARM 1 */ 1507 #define PLOGX_IOCBERR_HNDLUSED 0x1b /* further info in IOPARM 1 */ 1508 #define PLOGX_IOCBERR_NOHANDLE 0x1c 1509 #define PLOGX_IOCBERR_NOFLOGI 0x1f /* further info in IOPARM 1 */ 1510 1511 #define PLOGX_FLG_CMD_MASK 0xf 1512 #define PLOGX_FLG_CMD_PLOGI 0 1513 #define PLOGX_FLG_CMD_PRLI 1 1514 #define PLOGX_FLG_CMD_PDISC 2 1515 #define PLOGX_FLG_CMD_LOGO 8 1516 #define PLOGX_FLG_CMD_PRLO 9 1517 #define PLOGX_FLG_CMD_TPRLO 10 1518 1519 #define PLOGX_FLG_COND_PLOGI 0x10 /* if with PLOGI */ 1520 #define PLOGX_FLG_IMPLICIT 0x10 /* if with LOGO, PRLO, TPRLO */ 1521 #define PLOGX_FLG_SKIP_PRLI 0x20 /* if with PLOGI */ 1522 #define PLOGX_FLG_IMPLICIT_LOGO_ALL 0x20 /* if with LOGO */ 1523 #define PLOGX_FLG_EXPLICIT_LOGO 0x40 /* if with LOGO */ 1524 #define PLOGX_FLG_COMMON_FEATURES 0x80 /* if with PLOGI */ 1525 #define PLOGX_FLG_FREE_NPHDL 0x80 /* if with with LOGO */ 1526 1527 #define PLOGX_FLG_CLASS2 0x100 /* if with PLOGI */ 1528 #define PLOGX_FLG_FCP2_OVERRIDE 0x200 /* if with PRLOG, PRLI */ 1529 1530 /* 1531 * Report ID Acquisistion (24XX multi-id firmware) 1532 */ 1533 typedef struct { 1534 isphdr_t ridacq_hdr; 1535 uint32_t ridacq_handle; 1536 uint8_t ridacq_vp_acquired; 1537 uint8_t ridacq_vp_setup; 1538 uint8_t ridacq_vp_index; 1539 uint8_t ridacq_vp_status; 1540 uint16_t ridacq_vp_port_lo; 1541 uint8_t ridacq_vp_port_hi; 1542 uint8_t ridacq_format; /* 0 or 1 */ 1543 uint16_t ridacq_map[8]; 1544 uint8_t ridacq_reserved1[32]; 1545 } isp_ridacq_t; 1546 1547 #define RIDACQ_STS_COMPLETE 0 1548 #define RIDACQ_STS_UNACQUIRED 1 1549 #define RIDACQ_STS_CHANGED 2 1550 #define RIDACQ_STS_SNS_TIMEOUT 3 1551 #define RIDACQ_STS_SNS_REJECTED 4 1552 #define RIDACQ_STS_SCR_TIMEOUT 5 1553 #define RIDACQ_STS_SCR_REJECTED 6 1554 1555 /* 1556 * Simple Name Server Data Structures 1557 */ 1558 #define SNS_GA_NXT 0x100 1559 #define SNS_GPN_ID 0x112 1560 #define SNS_GNN_ID 0x113 1561 #define SNS_GFT_ID 0x117 1562 #define SNS_GFF_ID 0x11F 1563 #define SNS_GID_FT 0x171 1564 #define SNS_GID_PT 0x1A1 1565 #define SNS_RFT_ID 0x217 1566 #define SNS_RSPN_ID 0x218 1567 #define SNS_RFF_ID 0x21F 1568 #define SNS_RSNN_NN 0x239 1569 typedef struct { 1570 uint16_t snscb_rblen; /* response buffer length (words) */ 1571 uint16_t snscb_reserved0; 1572 uint16_t snscb_addr[4]; /* response buffer address */ 1573 uint16_t snscb_sblen; /* subcommand buffer length (words) */ 1574 uint16_t snscb_reserved1; 1575 uint16_t snscb_data[]; /* variable data */ 1576 } sns_screq_t; /* Subcommand Request Structure */ 1577 1578 typedef struct { 1579 uint16_t snscb_rblen; /* response buffer length (words) */ 1580 uint16_t snscb_reserved0; 1581 uint16_t snscb_addr[4]; /* response buffer address */ 1582 uint16_t snscb_sblen; /* subcommand buffer length (words) */ 1583 uint16_t snscb_reserved1; 1584 uint16_t snscb_cmd; 1585 uint16_t snscb_reserved2; 1586 uint32_t snscb_reserved3; 1587 uint32_t snscb_port; 1588 } sns_ga_nxt_req_t; 1589 #define SNS_GA_NXT_REQ_SIZE (sizeof (sns_ga_nxt_req_t)) 1590 1591 typedef struct { /* Used for GFT_ID, GFF_ID, etc. */ 1592 uint16_t snscb_rblen; /* response buffer length (words) */ 1593 uint16_t snscb_reserved0; 1594 uint16_t snscb_addr[4]; /* response buffer address */ 1595 uint16_t snscb_sblen; /* subcommand buffer length (words) */ 1596 uint16_t snscb_reserved1; 1597 uint16_t snscb_cmd; 1598 uint16_t snscb_mword_div_2; 1599 uint32_t snscb_reserved3; 1600 uint32_t snscb_portid; 1601 } sns_gxx_id_req_t; 1602 #define SNS_GXX_ID_REQ_SIZE (sizeof (sns_gxx_id_req_t)) 1603 1604 typedef struct { 1605 uint16_t snscb_rblen; /* response buffer length (words) */ 1606 uint16_t snscb_reserved0; 1607 uint16_t snscb_addr[4]; /* response buffer address */ 1608 uint16_t snscb_sblen; /* subcommand buffer length (words) */ 1609 uint16_t snscb_reserved1; 1610 uint16_t snscb_cmd; 1611 uint16_t snscb_mword_div_2; 1612 uint32_t snscb_reserved3; 1613 uint32_t snscb_fc4_type; 1614 } sns_gid_ft_req_t; 1615 #define SNS_GID_FT_REQ_SIZE (sizeof (sns_gid_ft_req_t)) 1616 1617 typedef struct { 1618 uint16_t snscb_rblen; /* response buffer length (words) */ 1619 uint16_t snscb_reserved0; 1620 uint16_t snscb_addr[4]; /* response buffer address */ 1621 uint16_t snscb_sblen; /* subcommand buffer length (words) */ 1622 uint16_t snscb_reserved1; 1623 uint16_t snscb_cmd; 1624 uint16_t snscb_mword_div_2; 1625 uint32_t snscb_reserved3; 1626 uint8_t snscb_port_type; 1627 uint8_t snscb_domain; 1628 uint8_t snscb_area; 1629 uint8_t snscb_flags; 1630 } sns_gid_pt_req_t; 1631 #define SNS_GID_PT_REQ_SIZE (sizeof (sns_gid_pt_req_t)) 1632 1633 typedef struct { 1634 uint16_t snscb_rblen; /* response buffer length (words) */ 1635 uint16_t snscb_reserved0; 1636 uint16_t snscb_addr[4]; /* response buffer address */ 1637 uint16_t snscb_sblen; /* subcommand buffer length (words) */ 1638 uint16_t snscb_reserved1; 1639 uint16_t snscb_cmd; 1640 uint16_t snscb_reserved2; 1641 uint32_t snscb_reserved3; 1642 uint32_t snscb_port; 1643 uint32_t snscb_fc4_types[8]; 1644 } sns_rft_id_req_t; 1645 #define SNS_RFT_ID_REQ_SIZE (sizeof (sns_rft_id_req_t)) 1646 1647 typedef struct { 1648 ct_hdr_t snscb_cthdr; 1649 uint8_t snscb_port_type; 1650 uint8_t snscb_port_id[3]; 1651 uint8_t snscb_portname[8]; 1652 uint16_t snscb_data[]; /* variable data */ 1653 } sns_scrsp_t; /* Subcommand Response Structure */ 1654 1655 typedef struct { 1656 ct_hdr_t snscb_cthdr; 1657 uint8_t snscb_port_type; 1658 uint8_t snscb_port_id[3]; 1659 uint8_t snscb_portname[8]; 1660 uint8_t snscb_pnlen; /* symbolic port name length */ 1661 uint8_t snscb_pname[255]; /* symbolic port name */ 1662 uint8_t snscb_nodename[8]; 1663 uint8_t snscb_nnlen; /* symbolic node name length */ 1664 uint8_t snscb_nname[255]; /* symbolic node name */ 1665 uint8_t snscb_ipassoc[8]; 1666 uint8_t snscb_ipaddr[16]; 1667 uint8_t snscb_svc_class[4]; 1668 uint8_t snscb_fc4_types[32]; 1669 uint8_t snscb_fpname[8]; 1670 uint8_t snscb_reserved; 1671 uint8_t snscb_hardaddr[3]; 1672 } sns_ga_nxt_rsp_t; /* Subcommand Response Structure */ 1673 #define SNS_GA_NXT_RESP_SIZE (sizeof (sns_ga_nxt_rsp_t)) 1674 1675 typedef struct { 1676 ct_hdr_t snscb_cthdr; 1677 uint8_t snscb_wwn[8]; 1678 } sns_gxn_id_rsp_t; 1679 #define SNS_GXN_ID_RESP_SIZE (sizeof (sns_gxn_id_rsp_t)) 1680 1681 typedef struct { 1682 ct_hdr_t snscb_cthdr; 1683 uint32_t snscb_fc4_types[8]; 1684 } sns_gft_id_rsp_t; 1685 #define SNS_GFT_ID_RESP_SIZE (sizeof (sns_gft_id_rsp_t)) 1686 1687 typedef struct { 1688 ct_hdr_t snscb_cthdr; 1689 uint32_t snscb_fc4_features[32]; 1690 } sns_gff_id_rsp_t; 1691 #define SNS_GFF_ID_RESP_SIZE (sizeof (sns_gff_id_rsp_t)) 1692 1693 typedef struct { /* Used for GID_FT, GID_PT, etc. */ 1694 ct_hdr_t snscb_cthdr; 1695 struct { 1696 uint8_t control; 1697 uint8_t portid[3]; 1698 } snscb_ports[1]; 1699 } sns_gid_xx_rsp_t; 1700 #define SNS_GID_XX_RESP_SIZE(x) ((sizeof (sns_gid_xx_rsp_t)) + ((x - 1) << 2)) 1701 1702 /* 1703 * Other Misc Structures 1704 */ 1705 1706 /* ELS Pass Through */ 1707 typedef struct { 1708 isphdr_t els_hdr; 1709 uint32_t els_handle; 1710 uint16_t els_status; 1711 uint16_t els_nphdl; 1712 uint16_t els_xmit_dsd_count; /* outgoing only */ 1713 uint8_t els_vphdl; 1714 uint8_t els_sof; 1715 uint32_t els_rxid; 1716 uint16_t els_recv_dsd_count; /* outgoing only */ 1717 uint8_t els_opcode; 1718 uint8_t els_reserved1; 1719 uint8_t els_did_lo; 1720 uint8_t els_did_mid; 1721 uint8_t els_did_hi; 1722 uint8_t els_reserved2; 1723 uint16_t els_reserved3; 1724 uint16_t els_ctl_flags; 1725 union { 1726 struct { 1727 uint32_t _els_bytecnt; 1728 uint32_t _els_subcode1; 1729 uint32_t _els_subcode2; 1730 uint8_t _els_reserved4[20]; 1731 } in; 1732 struct { 1733 uint32_t _els_recv_bytecnt; 1734 uint32_t _els_xmit_bytecnt; 1735 uint32_t _els_xmit_dsd_length; 1736 uint16_t _els_xmit_dsd_a1500; 1737 uint16_t _els_xmit_dsd_a3116; 1738 uint16_t _els_xmit_dsd_a4732; 1739 uint16_t _els_xmit_dsd_a6348; 1740 uint32_t _els_recv_dsd_length; 1741 uint16_t _els_recv_dsd_a1500; 1742 uint16_t _els_recv_dsd_a3116; 1743 uint16_t _els_recv_dsd_a4732; 1744 uint16_t _els_recv_dsd_a6348; 1745 } out; 1746 } inout; 1747 #define els_bytecnt inout.in._els_bytecnt 1748 #define els_subcode1 inout.in._els_subcode1 1749 #define els_subcode2 inout.in._els_subcode2 1750 #define els_reserved4 inout.in._els_reserved4 1751 #define els_recv_bytecnt inout.out._els_recv_bytecnt 1752 #define els_xmit_bytecnt inout.out._els_xmit_bytecnt 1753 #define els_xmit_dsd_length inout.out._els_xmit_dsd_length 1754 #define els_xmit_dsd_a1500 inout.out._els_xmit_dsd_a1500 1755 #define els_xmit_dsd_a3116 inout.out._els_xmit_dsd_a3116 1756 #define els_xmit_dsd_a4732 inout.out._els_xmit_dsd_a4732 1757 #define els_xmit_dsd_a6348 inout.out._els_xmit_dsd_a6348 1758 #define els_recv_dsd_length inout.out._els_recv_dsd_length 1759 #define els_recv_dsd_a1500 inout.out._els_recv_dsd_a1500 1760 #define els_recv_dsd_a3116 inout.out._els_recv_dsd_a3116 1761 #define els_recv_dsd_a4732 inout.out._els_recv_dsd_a4732 1762 #define els_recv_dsd_a6348 inout.out._els_recv_dsd_a6348 1763 } els_t; 1764 1765 /* 1766 * A handy package structure for running FC-SCSI commands internally 1767 */ 1768 typedef struct { 1769 uint16_t handle; 1770 uint16_t lun; 1771 uint32_t 1772 channel : 8, 1773 portid : 24; 1774 uint32_t timeout; 1775 union { 1776 struct { 1777 uint32_t data_length; 1778 uint32_t 1779 no_wait : 1, 1780 do_read : 1; 1781 uint8_t cdb[16]; 1782 void *data_ptr; 1783 } beg; 1784 struct { 1785 uint32_t data_residual; 1786 uint8_t status; 1787 uint8_t pad; 1788 uint16_t sense_length; 1789 uint8_t sense_data[32]; 1790 } end; 1791 } fcd; 1792 } isp_xcmd_t; 1793 1794 /* 1795 * Target Mode related definitions 1796 */ 1797 #define QLTM_SENSELEN 18 /* non-FC cards only */ 1798 #define QLTM_SVALID 0x80 1799 1800 /* 1801 * Structure for Enable Lun and Modify Lun queue entries 1802 */ 1803 typedef struct { 1804 isphdr_t le_header; 1805 uint32_t le_reserved; 1806 uint8_t le_lun; 1807 uint8_t le_rsvd; 1808 uint8_t le_ops; /* Modify LUN only */ 1809 uint8_t le_tgt; /* Not for FC */ 1810 uint32_t le_flags; /* Not for FC */ 1811 uint8_t le_status; 1812 uint8_t le_reserved2; 1813 uint8_t le_cmd_count; 1814 uint8_t le_in_count; 1815 uint8_t le_cdb6len; /* Not for FC */ 1816 uint8_t le_cdb7len; /* Not for FC */ 1817 uint16_t le_timeout; 1818 uint16_t le_reserved3[20]; 1819 } lun_entry_t; 1820 1821 /* 1822 * le_flags values 1823 */ 1824 #define LUN_TQAE 0x00000002 /* bit1 Tagged Queue Action Enable */ 1825 #define LUN_DSSM 0x01000000 /* bit24 Disable Sending SDP Message */ 1826 #define LUN_DISAD 0x02000000 /* bit25 Disable autodisconnect */ 1827 #define LUN_DM 0x40000000 /* bit30 Disconnects Mandatory */ 1828 1829 /* 1830 * le_ops values 1831 */ 1832 #define LUN_CCINCR 0x01 /* increment command count */ 1833 #define LUN_CCDECR 0x02 /* decrement command count */ 1834 #define LUN_ININCR 0x40 /* increment immed. notify count */ 1835 #define LUN_INDECR 0x80 /* decrement immed. notify count */ 1836 1837 /* 1838 * le_status values 1839 */ 1840 #define LUN_OK 0x01 /* we be rockin' */ 1841 #define LUN_ERR 0x04 /* request completed with error */ 1842 #define LUN_INVAL 0x06 /* invalid request */ 1843 #define LUN_NOCAP 0x16 /* can't provide requested capability */ 1844 #define LUN_ENABLED 0x3E /* LUN already enabled */ 1845 1846 /* 1847 * Immediate Notify Entry structure 1848 */ 1849 #define IN_MSGLEN 8 /* 8 bytes */ 1850 #define IN_RSVDLEN 8 /* 8 words */ 1851 typedef struct { 1852 isphdr_t in_header; 1853 uint32_t in_reserved; 1854 uint8_t in_lun; /* lun */ 1855 uint8_t in_iid; /* initiator */ 1856 uint8_t in_reserved2; 1857 uint8_t in_tgt; /* target */ 1858 uint32_t in_flags; 1859 uint8_t in_status; 1860 uint8_t in_rsvd2; 1861 uint8_t in_tag_val; /* tag value */ 1862 uint8_t in_tag_type; /* tag type */ 1863 uint16_t in_seqid; /* sequence id */ 1864 uint8_t in_msg[IN_MSGLEN]; /* SCSI message bytes */ 1865 uint16_t in_reserved3[IN_RSVDLEN]; 1866 uint8_t in_sense[QLTM_SENSELEN];/* suggested sense data */ 1867 } in_entry_t; 1868 1869 typedef struct { 1870 isphdr_t in_header; 1871 uint32_t in_reserved; 1872 uint8_t in_lun; /* lun */ 1873 uint8_t in_iid; /* initiator */ 1874 uint16_t in_scclun; 1875 uint32_t in_reserved2; 1876 uint16_t in_status; 1877 uint16_t in_task_flags; 1878 uint16_t in_seqid; /* sequence id */ 1879 } in_fcentry_t; 1880 1881 typedef struct { 1882 isphdr_t in_header; 1883 uint32_t in_reserved; 1884 uint16_t in_iid; /* initiator */ 1885 uint16_t in_scclun; 1886 uint32_t in_reserved2; 1887 uint16_t in_status; 1888 uint16_t in_task_flags; 1889 uint16_t in_seqid; /* sequence id */ 1890 } in_fcentry_e_t; 1891 1892 /* 1893 * Values for the in_status field 1894 */ 1895 #define IN_REJECT 0x0D /* Message Reject message received */ 1896 #define IN_RESET 0x0E /* Bus Reset occurred */ 1897 #define IN_NO_RCAP 0x16 /* requested capability not available */ 1898 #define IN_IDE_RECEIVED 0x33 /* Initiator Detected Error msg received */ 1899 #define IN_RSRC_UNAVAIL 0x34 /* resource unavailable */ 1900 #define IN_MSG_RECEIVED 0x36 /* SCSI message received */ 1901 #define IN_ABORT_TASK 0x20 /* task named in RX_ID is being aborted (FC) */ 1902 #define IN_PORT_LOGOUT 0x29 /* port has logged out (FC) */ 1903 #define IN_PORT_CHANGED 0x2A /* port changed */ 1904 #define IN_GLOBAL_LOGO 0x2E /* all ports logged out */ 1905 #define IN_NO_NEXUS 0x3B /* Nexus not established */ 1906 #define IN_SRR_RCVD 0x45 /* SRR received */ 1907 1908 /* 1909 * Values for the in_task_flags field- should only get one at a time! 1910 */ 1911 #define TASK_FLAGS_RESERVED_MASK (0xe700) 1912 #define TASK_FLAGS_CLEAR_ACA (1<<14) 1913 #define TASK_FLAGS_TARGET_RESET (1<<13) 1914 #define TASK_FLAGS_LUN_RESET (1<<12) 1915 #define TASK_FLAGS_CLEAR_TASK_SET (1<<10) 1916 #define TASK_FLAGS_ABORT_TASK_SET (1<<9) 1917 1918 /* 1919 * ISP24XX Immediate Notify 1920 */ 1921 typedef struct { 1922 isphdr_t in_header; 1923 uint32_t in_reserved; 1924 uint16_t in_nphdl; 1925 uint16_t in_reserved1; 1926 uint16_t in_flags; 1927 uint16_t in_srr_rxid; 1928 uint16_t in_status; 1929 uint8_t in_status_subcode; 1930 uint8_t in_fwhandle; 1931 uint32_t in_rxid; 1932 uint16_t in_srr_reloff_lo; 1933 uint16_t in_srr_reloff_hi; 1934 uint16_t in_srr_iu; 1935 uint16_t in_srr_oxid; 1936 /* 1937 * If bit 2 is set in in_flags, the N-Port and 1938 * handle tags are valid. If the received ELS is 1939 * a LOGO, then these tags contain the N Port ID 1940 * from the LOGO payload. If the received ELS 1941 * request is TPRLO, these tags contain the 1942 * Third Party Originator N Port ID. 1943 */ 1944 uint16_t in_nport_id_hi; 1945 #define in_prli_options in_nport_id_hi 1946 uint8_t in_nport_id_lo; 1947 uint8_t in_reserved3; 1948 uint16_t in_np_handle; 1949 uint8_t in_reserved4[12]; 1950 uint8_t in_reserved5; 1951 uint8_t in_vpidx; 1952 uint32_t in_reserved6; 1953 uint16_t in_portid_lo; 1954 uint8_t in_portid_hi; 1955 uint8_t in_reserved7; 1956 uint16_t in_reserved8; 1957 uint16_t in_oxid; 1958 } in_fcentry_24xx_t; 1959 1960 #define IN24XX_FLAG_PUREX_IOCB 0x1 1961 #define IN24XX_FLAG_GLOBAL_LOGOUT 0x2 1962 #define IN24XX_FLAG_NPHDL_VALID 0x4 1963 #define IN24XX_FLAG_N2N_PRLI 0x8 1964 #define IN24XX_FLAG_PN_NN_VALID 0x10 1965 1966 #define IN24XX_LIP_RESET 0x0E 1967 #define IN24XX_LINK_RESET 0x0F 1968 #define IN24XX_PORT_LOGOUT 0x29 1969 #define IN24XX_PORT_CHANGED 0x2A 1970 #define IN24XX_LINK_FAILED 0x2E 1971 #define IN24XX_SRR_RCVD 0x45 1972 #define IN24XX_ELS_RCVD 0x46 /* 1973 * login-affectin ELS received- check 1974 * subcode for specific opcode 1975 */ 1976 1977 /* 1978 * For f/w > 4.0.25, these offsets in the Immediate Notify contain 1979 * the WWNN/WWPN if the ELS is PLOGI, PDISC or ADISC. The WWN is in 1980 * Big Endian format. 1981 */ 1982 #define IN24XX_PRLI_WWNN_OFF 0x18 1983 #define IN24XX_PRLI_WWPN_OFF 0x28 1984 #define IN24XX_PLOGI_WWNN_OFF 0x20 1985 #define IN24XX_PLOGI_WWPN_OFF 0x28 1986 1987 /* 1988 * For f/w > 4.0.25, this offset in the Immediate Notify contain 1989 * the WWPN if the ELS is LOGO. The WWN is in Big Endian format. 1990 */ 1991 #define IN24XX_LOGO_WWPN_OFF 0x28 1992 1993 /* 1994 * Immediate Notify Status Subcodes for IN24XX_PORT_LOGOUT 1995 */ 1996 #define IN24XX_PORT_LOGOUT_PDISC_TMO 0x00 1997 #define IN24XX_PORT_LOGOUT_UXPR_DISC 0x01 1998 #define IN24XX_PORT_LOGOUT_OWN_OPN 0x02 1999 #define IN24XX_PORT_LOGOUT_OWN_OPN_SFT 0x03 2000 #define IN24XX_PORT_LOGOUT_ABTS_TMO 0x04 2001 #define IN24XX_PORT_LOGOUT_DISC_RJT 0x05 2002 #define IN24XX_PORT_LOGOUT_LOGIN_NEEDED 0x06 2003 #define IN24XX_PORT_LOGOUT_BAD_DISC 0x07 2004 #define IN24XX_PORT_LOGOUT_LOST_ALPA 0x08 2005 #define IN24XX_PORT_LOGOUT_XMIT_FAILURE 0x09 2006 2007 /* 2008 * Immediate Notify Status Subcodes for IN24XX_PORT_CHANGED 2009 */ 2010 #define IN24XX_PORT_CHANGED_BADFAN 0x00 2011 #define IN24XX_PORT_CHANGED_TOPO_CHANGE 0x01 2012 #define IN24XX_PORT_CHANGED_FLOGI_ACC 0x02 2013 #define IN24XX_PORT_CHANGED_FLOGI_RJT 0x03 2014 #define IN24XX_PORT_CHANGED_TIMEOUT 0x04 2015 #define IN24XX_PORT_CHANGED_PORT_CHANGE 0x05 2016 2017 /* 2018 * Notify Acknowledge Entry structure 2019 */ 2020 #define NA_RSVDLEN 22 2021 typedef struct { 2022 isphdr_t na_header; 2023 uint32_t na_reserved; 2024 uint8_t na_lun; /* lun */ 2025 uint8_t na_iid; /* initiator */ 2026 uint8_t na_reserved2; 2027 uint8_t na_tgt; /* target */ 2028 uint32_t na_flags; 2029 uint8_t na_status; 2030 uint8_t na_event; 2031 uint16_t na_seqid; /* sequence id */ 2032 uint16_t na_reserved3[NA_RSVDLEN]; 2033 } na_entry_t; 2034 2035 /* 2036 * Value for the na_event field 2037 */ 2038 #define NA_RST_CLRD 0x80 /* Clear an async event notification */ 2039 #define NA_OK 0x01 /* Notify Acknowledge Succeeded */ 2040 #define NA_INVALID 0x06 /* Invalid Notify Acknowledge */ 2041 2042 #define NA2_RSVDLEN 21 2043 typedef struct { 2044 isphdr_t na_header; 2045 uint32_t na_reserved; 2046 uint8_t na_reserved1; 2047 uint8_t na_iid; /* initiator loop id */ 2048 uint16_t na_response; 2049 uint16_t na_flags; 2050 uint16_t na_reserved2; 2051 uint16_t na_status; 2052 uint16_t na_task_flags; 2053 uint16_t na_seqid; /* sequence id */ 2054 uint16_t na_reserved3[NA2_RSVDLEN]; 2055 } na_fcentry_t; 2056 2057 typedef struct { 2058 isphdr_t na_header; 2059 uint32_t na_reserved; 2060 uint16_t na_iid; /* initiator loop id */ 2061 uint16_t na_response; /* response code */ 2062 uint16_t na_flags; 2063 uint16_t na_reserved2; 2064 uint16_t na_status; 2065 uint16_t na_task_flags; 2066 uint16_t na_seqid; /* sequence id */ 2067 uint16_t na_reserved3[NA2_RSVDLEN]; 2068 } na_fcentry_e_t; 2069 2070 #define NAFC_RCOUNT 0x80 /* increment resource count */ 2071 #define NAFC_RST_CLRD 0x20 /* Clear LIP Reset */ 2072 #define NAFC_TVALID 0x10 /* task mangement response code is valid */ 2073 2074 /* 2075 * ISP24XX Notify Acknowledge 2076 */ 2077 2078 typedef struct { 2079 isphdr_t na_header; 2080 uint32_t na_handle; 2081 uint16_t na_nphdl; 2082 uint16_t na_reserved1; 2083 uint16_t na_flags; 2084 uint16_t na_srr_rxid; 2085 uint16_t na_status; 2086 uint8_t na_status_subcode; 2087 uint8_t na_fwhandle; 2088 uint32_t na_rxid; 2089 uint16_t na_srr_reloff_lo; 2090 uint16_t na_srr_reloff_hi; 2091 uint16_t na_srr_iu; 2092 uint16_t na_srr_flags; 2093 uint8_t na_reserved3[18]; 2094 uint8_t na_reserved4; 2095 uint8_t na_vpidx; 2096 uint8_t na_srr_reject_vunique; 2097 uint8_t na_srr_reject_explanation; 2098 uint8_t na_srr_reject_code; 2099 uint8_t na_reserved5; 2100 uint8_t na_reserved6[6]; 2101 uint16_t na_oxid; 2102 } na_fcentry_24xx_t; 2103 2104 /* 2105 * Accept Target I/O Entry structure 2106 */ 2107 #define ATIO_CDBLEN 26 2108 2109 typedef struct { 2110 isphdr_t at_header; 2111 uint16_t at_reserved; 2112 uint16_t at_handle; 2113 uint8_t at_lun; /* lun */ 2114 uint8_t at_iid; /* initiator */ 2115 uint8_t at_cdblen; /* cdb length */ 2116 uint8_t at_tgt; /* target */ 2117 uint32_t at_flags; 2118 uint8_t at_status; /* firmware status */ 2119 uint8_t at_scsi_status; /* scsi status */ 2120 uint8_t at_tag_val; /* tag value */ 2121 uint8_t at_tag_type; /* tag type */ 2122 uint8_t at_cdb[ATIO_CDBLEN]; /* received CDB */ 2123 uint8_t at_sense[QLTM_SENSELEN];/* suggested sense data */ 2124 } at_entry_t; 2125 2126 /* 2127 * at_flags values 2128 */ 2129 #define AT_NODISC 0x00008000 /* disconnect disabled */ 2130 #define AT_TQAE 0x00000002 /* Tagged Queue Action enabled */ 2131 2132 /* 2133 * at_status values 2134 */ 2135 #define AT_PATH_INVALID 0x07 /* ATIO sent to firmware for disabled lun */ 2136 #define AT_RESET 0x0E /* SCSI Bus Reset Occurred */ 2137 #define AT_PHASE_ERROR 0x14 /* Bus phase sequence error */ 2138 #define AT_NOCAP 0x16 /* Requested capability not available */ 2139 #define AT_BDR_MSG 0x17 /* Bus Device Reset msg received */ 2140 #define AT_CDB 0x3D /* CDB received */ 2141 /* 2142 * Macros to create and fetch and test concatenated handle and tag value macros 2143 * (SPI only) 2144 */ 2145 #define AT_MAKE_TAGID(tid, aep) \ 2146 tid = aep->at_handle; \ 2147 if (aep->at_flags & AT_TQAE) { \ 2148 tid |= (aep->at_tag_val << 16); \ 2149 tid |= (1 << 24); \ 2150 } 2151 2152 #define CT_MAKE_TAGID(tid, ct) \ 2153 tid = ct->ct_fwhandle; \ 2154 if (ct->ct_flags & CT_TQAE) { \ 2155 tid |= (ct->ct_tag_val << 16); \ 2156 tid |= (1 << 24); \ 2157 } 2158 2159 #define AT_HAS_TAG(val) ((val) & (1 << 24)) 2160 #define AT_GET_TAG(val) (((val) >> 16) & 0xff) 2161 #define AT_GET_HANDLE(val) ((val) & 0xffff) 2162 2163 #define IN_MAKE_TAGID(tid, inp) \ 2164 tid = inp->in_seqid; \ 2165 tid |= (inp->in_tag_val << 16); \ 2166 tid |= (1 << 24) 2167 2168 /* 2169 * Accept Target I/O Entry structure, Type 2 2170 */ 2171 #define ATIO2_CDBLEN 16 2172 2173 typedef struct { 2174 isphdr_t at_header; 2175 uint32_t at_reserved; 2176 uint8_t at_lun; /* lun or reserved */ 2177 uint8_t at_iid; /* initiator */ 2178 uint16_t at_rxid; /* response ID */ 2179 uint16_t at_flags; 2180 uint16_t at_status; /* firmware status */ 2181 uint8_t at_crn; /* command reference number */ 2182 uint8_t at_taskcodes; 2183 uint8_t at_taskflags; 2184 uint8_t at_execodes; 2185 uint8_t at_cdb[ATIO2_CDBLEN]; /* received CDB */ 2186 uint32_t at_datalen; /* allocated data len */ 2187 uint16_t at_scclun; /* SCC Lun or reserved */ 2188 uint16_t at_wwpn[4]; /* WWPN of initiator */ 2189 uint16_t at_reserved2[6]; 2190 uint16_t at_oxid; 2191 } at2_entry_t; 2192 2193 typedef struct { 2194 isphdr_t at_header; 2195 uint32_t at_reserved; 2196 uint16_t at_iid; /* initiator */ 2197 uint16_t at_rxid; /* response ID */ 2198 uint16_t at_flags; 2199 uint16_t at_status; /* firmware status */ 2200 uint8_t at_crn; /* command reference number */ 2201 uint8_t at_taskcodes; 2202 uint8_t at_taskflags; 2203 uint8_t at_execodes; 2204 uint8_t at_cdb[ATIO2_CDBLEN]; /* received CDB */ 2205 uint32_t at_datalen; /* allocated data len */ 2206 uint16_t at_scclun; /* SCC Lun or reserved */ 2207 uint16_t at_wwpn[4]; /* WWPN of initiator */ 2208 uint16_t at_reserved2[6]; 2209 uint16_t at_oxid; 2210 } at2e_entry_t; 2211 2212 #define ATIO2_WWPN_OFFSET 0x2A 2213 #define ATIO2_OXID_OFFSET 0x3E 2214 2215 #define ATIO2_TC_ATTR_MASK 0x7 2216 #define ATIO2_TC_ATTR_SIMPLEQ 0 2217 #define ATIO2_TC_ATTR_HEADOFQ 1 2218 #define ATIO2_TC_ATTR_ORDERED 2 2219 #define ATIO2_TC_ATTR_ACAQ 4 2220 #define ATIO2_TC_ATTR_UNTAGGED 5 2221 2222 #define ATIO2_EX_WRITE 0x1 2223 #define ATIO2_EX_READ 0x2 2224 /* 2225 * Macros to create and fetch and test concatenated handle and tag value macros 2226 */ 2227 #define AT2_MAKE_TAGID(tid, bus, inst, aep) \ 2228 tid = aep->at_rxid; \ 2229 tid |= (((uint64_t)inst) << 32); \ 2230 tid |= (((uint64_t)bus) << 48) 2231 2232 #define CT2_MAKE_TAGID(tid, bus, inst, ct) \ 2233 tid = ct->ct_rxid; \ 2234 tid |= (((uint64_t)inst) << 32); \ 2235 tid |= (((uint64_t)(bus & 0xff)) << 48) 2236 2237 #define AT2_HAS_TAG(val) 1 2238 #define AT2_GET_TAG(val) ((val) & 0xffffffff) 2239 #define AT2_GET_INST(val) (((val) >> 32) & 0xffff) 2240 #define AT2_GET_HANDLE AT2_GET_TAG 2241 #define AT2_GET_BUS(val) (((val) >> 48) & 0xff) 2242 2243 #define FC_HAS_TAG AT2_HAS_TAG 2244 #define FC_GET_TAG AT2_GET_TAG 2245 #define FC_GET_INST AT2_GET_INST 2246 #define FC_GET_HANDLE AT2_GET_HANDLE 2247 2248 #define IN_FC_MAKE_TAGID(tid, bus, inst, seqid) \ 2249 tid = seqid; \ 2250 tid |= (((uint64_t)inst) << 32); \ 2251 tid |= (((uint64_t)(bus & 0xff)) << 48) 2252 2253 #define FC_TAG_INSERT_INST(tid, inst) \ 2254 tid &= ~0x0000ffff00000000ull; \ 2255 tid |= (((uint64_t)inst) << 32) 2256 2257 /* 2258 * 24XX ATIO Definition 2259 * 2260 * This is *quite* different from other entry types. 2261 * First of all, it has its own queue it comes in on. 2262 * 2263 * Secondly, it doesn't have a normal header. 2264 * 2265 * Thirdly, it's just a passthru of the FCP CMND IU 2266 * which is recorded in big endian mode. 2267 */ 2268 typedef struct { 2269 uint8_t at_type; 2270 uint8_t at_count; 2271 /* 2272 * Task attribute in high four bits, 2273 * the rest is the FCP CMND IU Length. 2274 * NB: the command can extend past the 2275 * length for a single queue entry. 2276 */ 2277 uint16_t at_ta_len; 2278 uint32_t at_rxid; 2279 fc_hdr_t at_hdr; 2280 fcp_cmnd_iu_t at_cmnd; 2281 } at7_entry_t; 2282 #define AT7_NORESRC_RXID 0xffffffff 2283 2284 2285 /* 2286 * Continue Target I/O Entry structure 2287 * Request from driver. The response from the 2288 * ISP firmware is the same except that the last 18 2289 * bytes are overwritten by suggested sense data if 2290 * the 'autosense valid' bit is set in the status byte. 2291 */ 2292 typedef struct { 2293 isphdr_t ct_header; 2294 uint16_t ct_syshandle; 2295 uint16_t ct_fwhandle; /* required by f/w */ 2296 uint8_t ct_lun; /* lun */ 2297 uint8_t ct_iid; /* initiator id */ 2298 uint8_t ct_reserved2; 2299 uint8_t ct_tgt; /* our target id */ 2300 uint32_t ct_flags; 2301 uint8_t ct_status; /* isp status */ 2302 uint8_t ct_scsi_status; /* scsi status */ 2303 uint8_t ct_tag_val; /* tag value */ 2304 uint8_t ct_tag_type; /* tag type */ 2305 uint32_t ct_xfrlen; /* transfer length */ 2306 uint32_t ct_resid; /* residual length */ 2307 uint16_t ct_timeout; 2308 uint16_t ct_seg_count; 2309 ispds_t ct_dataseg[ISP_RQDSEG]; 2310 } ct_entry_t; 2311 2312 /* 2313 * For some of the dual port SCSI adapters, port (bus #) is reported 2314 * in the MSbit of ct_iid. Bit fields are a bit too awkward here. 2315 * 2316 * Note that this does not apply to FC adapters at all which can and 2317 * do report IIDs between 0x81 && 0xfe (or 0x7ff) which represent devices 2318 * that have logged in across a SCSI fabric. 2319 */ 2320 #define GET_IID_VAL(x) (x & 0x3f) 2321 #define GET_BUS_VAL(x) ((x >> 7) & 0x1) 2322 #define SET_IID_VAL(y, x) y = ((y & ~0x3f) | (x & 0x3f)) 2323 #define SET_BUS_VAL(y, x) y = ((y & 0x3f) | ((x & 0x1) << 7)) 2324 2325 /* 2326 * ct_flags values 2327 */ 2328 #define CT_TQAE 0x00000002 /* bit 1, Tagged Queue Action enable */ 2329 #define CT_DATA_IN 0x00000040 /* bits 6&7, Data direction - *to* initiator */ 2330 #define CT_DATA_OUT 0x00000080 /* bits 6&7, Data direction - *from* initiator */ 2331 #define CT_NO_DATA 0x000000C0 /* bits 6&7, Data direction */ 2332 #define CT_CCINCR 0x00000100 /* bit 8, autoincrement atio count */ 2333 #define CT_DATAMASK 0x000000C0 /* bits 6&7, Data direction */ 2334 #define CT_INISYNCWIDE 0x00004000 /* bit 14, Do Sync/Wide Negotiation */ 2335 #define CT_NODISC 0x00008000 /* bit 15, Disconnects disabled */ 2336 #define CT_DSDP 0x01000000 /* bit 24, Disable Save Data Pointers */ 2337 #define CT_SENDRDP 0x04000000 /* bit 26, Send Restore Pointers msg */ 2338 #define CT_SENDSTATUS 0x80000000 /* bit 31, Send SCSI status byte */ 2339 2340 /* 2341 * ct_status values 2342 * - set by the firmware when it returns the CTIO 2343 */ 2344 #define CT_OK 0x01 /* completed without error */ 2345 #define CT_ABORTED 0x02 /* aborted by host */ 2346 #define CT_ERR 0x04 /* see sense data for error */ 2347 #define CT_INVAL 0x06 /* request for disabled lun */ 2348 #define CT_NOPATH 0x07 /* invalid ITL nexus */ 2349 #define CT_INVRXID 0x08 /* (FC only) Invalid RX_ID */ 2350 #define CT_DATA_OVER 0x09 /* (FC only) Data Overrun */ 2351 #define CT_RSELTMO 0x0A /* reselection timeout after 2 tries */ 2352 #define CT_TIMEOUT 0x0B /* timed out */ 2353 #define CT_RESET 0x0E /* SCSI Bus Reset occurred */ 2354 #define CT_PARITY 0x0F /* Uncorrectable Parity Error */ 2355 #define CT_BUS_ERROR 0x10 /* (FC Only) DMA PCI Error */ 2356 #define CT_PANIC 0x13 /* Unrecoverable Error */ 2357 #define CT_PHASE_ERROR 0x14 /* Bus phase sequence error */ 2358 #define CT_DATA_UNDER 0x15 /* (FC only) Data Underrun */ 2359 #define CT_BDR_MSG 0x17 /* Bus Device Reset msg received */ 2360 #define CT_TERMINATED 0x19 /* due to Terminate Transfer mbox cmd */ 2361 #define CT_PORTUNAVAIL 0x28 /* port not available */ 2362 #define CT_LOGOUT 0x29 /* port logout */ 2363 #define CT_PORTCHANGED 0x2A /* port changed */ 2364 #define CT_IDE 0x33 /* Initiator Detected Error */ 2365 #define CT_NOACK 0x35 /* Outstanding Immed. Notify. entry */ 2366 #define CT_SRR 0x45 /* SRR Received */ 2367 #define CT_LUN_RESET 0x48 /* Lun Reset Received */ 2368 2369 #define CT_HBA_RESET 0xffff /* pseudo error - command destroyed by HBA reset*/ 2370 2371 /* 2372 * When the firmware returns a CTIO entry, it may overwrite the last 2373 * part of the structure with sense data. This starts at offset 0x2E 2374 * into the entry, which is in the middle of ct_dataseg[1]. Rather 2375 * than define a new struct for this, I'm just using the sense data 2376 * offset. 2377 */ 2378 #define CTIO_SENSE_OFFSET 0x2E 2379 2380 /* 2381 * Entry length in u_longs. All entries are the same size so 2382 * any one will do as the numerator. 2383 */ 2384 #define UINT32_ENTRY_SIZE (sizeof(at_entry_t)/sizeof(uint32_t)) 2385 2386 /* 2387 * QLA2100 CTIO (type 2) entry 2388 */ 2389 #define MAXRESPLEN 26 2390 typedef struct { 2391 isphdr_t ct_header; 2392 uint32_t ct_syshandle; 2393 uint8_t ct_lun; /* lun */ 2394 uint8_t ct_iid; /* initiator id */ 2395 uint16_t ct_rxid; /* response ID */ 2396 uint16_t ct_flags; 2397 uint16_t ct_status; /* isp status */ 2398 uint16_t ct_timeout; 2399 uint16_t ct_seg_count; 2400 uint32_t ct_reloff; /* relative offset */ 2401 uint32_t ct_resid; /* residual length */ 2402 union { 2403 /* 2404 * The three different modes that the target driver 2405 * can set the CTIO{2,3,4} up as. 2406 * 2407 * The first is for sending FCP_DATA_IUs as well as 2408 * (optionally) sending a terminal SCSI status FCP_RSP_IU. 2409 * 2410 * The second is for sending SCSI sense data in an FCP_RSP_IU. 2411 * Note that no FCP_DATA_IUs will be sent. 2412 * 2413 * The third is for sending FCP_RSP_IUs as built specifically 2414 * in system memory as located by the isp_dataseg. 2415 */ 2416 struct { 2417 uint32_t _reserved; 2418 uint16_t _reserved2; 2419 uint16_t ct_scsi_status; 2420 uint32_t ct_xfrlen; 2421 union { 2422 ispds_t ct_dataseg[ISP_RQDSEG_T2]; 2423 ispds64_t ct_dataseg64[ISP_RQDSEG_T3]; 2424 ispdslist_t ct_dslist; 2425 } u; 2426 } m0; 2427 struct { 2428 uint16_t _reserved; 2429 uint16_t _reserved2; 2430 uint16_t ct_senselen; 2431 uint16_t ct_scsi_status; 2432 uint16_t ct_resplen; 2433 uint8_t ct_resp[MAXRESPLEN]; 2434 } m1; 2435 struct { 2436 uint32_t _reserved; 2437 uint16_t _reserved2; 2438 uint16_t _reserved3; 2439 uint32_t ct_datalen; 2440 union { 2441 ispds_t ct_fcp_rsp_iudata_32; 2442 ispds64_t ct_fcp_rsp_iudata_64; 2443 } u; 2444 } m2; 2445 } rsp; 2446 } ct2_entry_t; 2447 2448 typedef struct { 2449 isphdr_t ct_header; 2450 uint32_t ct_syshandle; 2451 uint16_t ct_iid; /* initiator id */ 2452 uint16_t ct_rxid; /* response ID */ 2453 uint16_t ct_flags; 2454 uint16_t ct_status; /* isp status */ 2455 uint16_t ct_timeout; 2456 uint16_t ct_seg_count; 2457 uint32_t ct_reloff; /* relative offset */ 2458 uint32_t ct_resid; /* residual length */ 2459 union { 2460 struct { 2461 uint32_t _reserved; 2462 uint16_t _reserved2; 2463 uint16_t ct_scsi_status; 2464 uint32_t ct_xfrlen; 2465 union { 2466 ispds_t ct_dataseg[ISP_RQDSEG_T2]; 2467 ispds64_t ct_dataseg64[ISP_RQDSEG_T3]; 2468 ispdslist_t ct_dslist; 2469 } u; 2470 } m0; 2471 struct { 2472 uint16_t _reserved; 2473 uint16_t _reserved2; 2474 uint16_t ct_senselen; 2475 uint16_t ct_scsi_status; 2476 uint16_t ct_resplen; 2477 uint8_t ct_resp[MAXRESPLEN]; 2478 } m1; 2479 struct { 2480 uint32_t _reserved; 2481 uint16_t _reserved2; 2482 uint16_t _reserved3; 2483 uint32_t ct_datalen; 2484 union { 2485 ispds_t ct_fcp_rsp_iudata_32; 2486 ispds64_t ct_fcp_rsp_iudata_64; 2487 } u; 2488 } m2; 2489 } rsp; 2490 } ct2e_entry_t; 2491 2492 /* 2493 * ct_flags values for CTIO2 2494 */ 2495 #define CT2_FLAG_MODE0 0x0000 2496 #define CT2_FLAG_MODE1 0x0001 2497 #define CT2_FLAG_MODE2 0x0002 2498 #define CT2_FLAG_MMASK 0x0003 2499 #define CT2_DATA_IN 0x0040 /* *to* initiator */ 2500 #define CT2_DATA_OUT 0x0080 /* *from* initiator */ 2501 #define CT2_NO_DATA 0x00C0 2502 #define CT2_DATAMASK 0x00C0 2503 #define CT2_CCINCR 0x0100 2504 #define CT2_FASTPOST 0x0200 2505 #define CT2_CONFIRM 0x2000 2506 #define CT2_TERMINATE 0x4000 2507 #define CT2_SENDSTATUS 0x8000 2508 2509 /* 2510 * ct_status values are (mostly) the same as that for ct_entry. 2511 */ 2512 2513 /* 2514 * ct_scsi_status values- the low 8 bits are the normal SCSI status 2515 * we know and love. The upper 8 bits are validity markers for FCP_RSP_IU 2516 * fields. 2517 */ 2518 #define CT2_RSPLEN_VALID 0x0100 2519 #define CT2_SNSLEN_VALID 0x0200 2520 #define CT2_DATA_OVER 0x0400 2521 #define CT2_DATA_UNDER 0x0800 2522 2523 /* 2524 * ISP24XX CTIO 2525 */ 2526 #define MAXRESPLEN_24XX 24 2527 typedef struct { 2528 isphdr_t ct_header; 2529 uint32_t ct_syshandle; 2530 uint16_t ct_nphdl; /* status on returned CTIOs */ 2531 uint16_t ct_timeout; 2532 uint16_t ct_seg_count; 2533 uint8_t ct_vpidx; 2534 uint8_t ct_xflags; 2535 uint16_t ct_iid_lo; /* low 16 bits of portid */ 2536 uint8_t ct_iid_hi; /* hi 8 bits of portid */ 2537 uint8_t ct_reserved; 2538 uint32_t ct_rxid; 2539 uint16_t ct_senselen; /* mode 1 only */ 2540 uint16_t ct_flags; 2541 uint32_t ct_resid; /* residual length */ 2542 uint16_t ct_oxid; 2543 uint16_t ct_scsi_status; /* modes 0 && 1 only */ 2544 union { 2545 struct { 2546 uint32_t reloff; 2547 uint32_t reserved0; 2548 uint32_t ct_xfrlen; 2549 uint32_t reserved1; 2550 ispds64_t ds; 2551 } m0; 2552 struct { 2553 uint16_t ct_resplen; 2554 uint16_t reserved; 2555 uint8_t ct_resp[MAXRESPLEN_24XX]; 2556 } m1; 2557 struct { 2558 uint32_t reserved0; 2559 uint32_t reserved1; 2560 uint32_t ct_datalen; 2561 uint32_t reserved2; 2562 ispds64_t ct_fcp_rsp_iudata; 2563 } m2; 2564 } rsp; 2565 } ct7_entry_t; 2566 2567 /* 2568 * ct_flags values for CTIO7 2569 */ 2570 #define CT7_NO_DATA 0x0000 2571 #define CT7_DATA_OUT 0x0001 /* *from* initiator */ 2572 #define CT7_DATA_IN 0x0002 /* *to* initiator */ 2573 #define CT7_DATAMASK 0x3 2574 #define CT7_DSD_ENABLE 0x0004 2575 #define CT7_CONF_STSFD 0x0010 2576 #define CT7_EXPLCT_CONF 0x0020 2577 #define CT7_FLAG_MODE0 0x0000 2578 #define CT7_FLAG_MODE1 0x0040 2579 #define CT7_FLAG_MODE2 0x0080 2580 #define CT7_FLAG_MMASK 0x00C0 2581 #define CT7_NOACK 0x0100 2582 #define CT7_TASK_ATTR_SHIFT 9 2583 #define CT7_CONFIRM 0x2000 2584 #define CT7_TERMINATE 0x4000 2585 #define CT7_SENDSTATUS 0x8000 2586 2587 /* 2588 * Type 7 CTIO status codes 2589 */ 2590 #define CT7_OK 0x01 /* completed without error */ 2591 #define CT7_ABORTED 0x02 /* aborted by host */ 2592 #define CT7_ERR 0x04 /* see sense data for error */ 2593 #define CT7_INVAL 0x06 /* request for disabled lun */ 2594 #define CT7_INVRXID 0x08 /* Invalid RX_ID */ 2595 #define CT7_DATA_OVER 0x09 /* Data Overrun */ 2596 #define CT7_TIMEOUT 0x0B /* timed out */ 2597 #define CT7_RESET 0x0E /* LIP Rset Received */ 2598 #define CT7_BUS_ERROR 0x10 /* DMA PCI Error */ 2599 #define CT7_REASSY_ERR 0x11 /* DMA reassembly error */ 2600 #define CT7_DATA_UNDER 0x15 /* Data Underrun */ 2601 #define CT7_PORTUNAVAIL 0x28 /* port not available */ 2602 #define CT7_LOGOUT 0x29 /* port logout */ 2603 #define CT7_PORTCHANGED 0x2A /* port changed */ 2604 #define CT7_SRR 0x45 /* SRR Received */ 2605 2606 /* 2607 * Other 24XX related target IOCBs 2608 */ 2609 2610 /* 2611 * ABTS Received 2612 */ 2613 typedef struct { 2614 isphdr_t abts_header; 2615 uint8_t abts_reserved0[6]; 2616 uint16_t abts_nphdl; 2617 uint16_t abts_reserved1; 2618 uint16_t abts_sof; 2619 uint32_t abts_rxid_abts; 2620 uint16_t abts_did_lo; 2621 uint8_t abts_did_hi; 2622 uint8_t abts_r_ctl; 2623 uint16_t abts_sid_lo; 2624 uint8_t abts_sid_hi; 2625 uint8_t abts_cs_ctl; 2626 uint16_t abts_fs_ctl; 2627 uint8_t abts_f_ctl; 2628 uint8_t abts_type; 2629 uint16_t abts_seq_cnt; 2630 uint8_t abts_df_ctl; 2631 uint8_t abts_seq_id; 2632 uint16_t abts_rx_id; 2633 uint16_t abts_ox_id; 2634 uint32_t abts_param; 2635 uint8_t abts_reserved2[16]; 2636 uint32_t abts_rxid_task; 2637 } abts_t; 2638 2639 typedef struct { 2640 isphdr_t abts_rsp_header; 2641 uint32_t abts_rsp_handle; 2642 uint16_t abts_rsp_status; 2643 uint16_t abts_rsp_nphdl; 2644 uint16_t abts_rsp_ctl_flags; 2645 uint16_t abts_rsp_sof; 2646 uint32_t abts_rsp_rxid_abts; 2647 uint16_t abts_rsp_did_lo; 2648 uint8_t abts_rsp_did_hi; 2649 uint8_t abts_rsp_r_ctl; 2650 uint16_t abts_rsp_sid_lo; 2651 uint8_t abts_rsp_sid_hi; 2652 uint8_t abts_rsp_cs_ctl; 2653 uint16_t abts_rsp_f_ctl_lo; 2654 uint8_t abts_rsp_f_ctl_hi; 2655 uint8_t abts_rsp_type; 2656 uint16_t abts_rsp_seq_cnt; 2657 uint8_t abts_rsp_df_ctl; 2658 uint8_t abts_rsp_seq_id; 2659 uint16_t abts_rsp_rx_id; 2660 uint16_t abts_rsp_ox_id; 2661 uint32_t abts_rsp_param; 2662 union { 2663 struct { 2664 uint16_t reserved; 2665 uint8_t last_seq_id; 2666 uint8_t seq_id_valid; 2667 uint16_t aborted_rx_id; 2668 uint16_t aborted_ox_id; 2669 uint16_t high_seq_cnt; 2670 uint16_t low_seq_cnt; 2671 uint8_t reserved2[4]; 2672 } ba_acc; 2673 struct { 2674 uint8_t vendor_unique; 2675 uint8_t explanation; 2676 uint8_t reason; 2677 uint8_t reserved; 2678 uint8_t reserved2[12]; 2679 } ba_rjt; 2680 struct { 2681 uint8_t reserved[8]; 2682 uint32_t subcode1; 2683 uint32_t subcode2; 2684 } rsp; 2685 uint8_t reserved[16]; 2686 } abts_rsp_payload; 2687 uint32_t abts_rsp_rxid_task; 2688 } abts_rsp_t; 2689 2690 /* terminate this ABTS exchange */ 2691 #define ISP24XX_ABTS_RSP_TERMINATE 0x01 2692 2693 #define ISP24XX_ABTS_RSP_COMPLETE 0x00 2694 #define ISP24XX_ABTS_RSP_RESET 0x04 2695 #define ISP24XX_ABTS_RSP_ABORTED 0x05 2696 #define ISP24XX_ABTS_RSP_TIMEOUT 0x06 2697 #define ISP24XX_ABTS_RSP_INVXID 0x08 2698 #define ISP24XX_ABTS_RSP_LOGOUT 0x29 2699 #define ISP24XX_ABTS_RSP_SUBCODE 0x31 2700 2701 #define ISP24XX_NO_TASK 0xffffffff 2702 2703 /* 2704 * Miscellaneous 2705 * 2706 * These are the limits of the number of dma segments we 2707 * can deal with based not on the size of the segment counter 2708 * (which is 16 bits), but on the size of the number of 2709 * queue entries field (which is 8 bits). We assume no 2710 * segments in the first queue entry, so we can either 2711 * have 7 dma segments per continuation entry or 5 2712 * (for 64 bit dma).. multiplying out by 254.... 2713 */ 2714 #define ISP_NSEG_MAX 1778 2715 #define ISP_NSEG64_MAX 1270 2716 2717 #endif /* _ISPMBOX_H */ 2718