1 /* $FreeBSD$ */ 2 /*- 3 * Copyright (c) 1997-2009 by Matthew Jacob 4 * All rights reserved. 5 * 6 * Redistribution and use in source and binary forms, with or without 7 * modification, are permitted provided that the following conditions 8 * are met: 9 * 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 16 * THIS SOFTWARE IS PROVIDED BY AUTHOR AND CONTRIBUTORS ``AS IS'' AND 17 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 18 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 19 * ARE DISCLAIMED. IN NO EVENT SHALL AUTHOR OR CONTRIBUTORS BE LIABLE 20 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 21 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 22 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 23 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 24 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 25 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 26 * SUCH DAMAGE. 27 * 28 */ 29 30 /* 31 * Mailbox and Queue Entry Definitions for for Qlogic ISP SCSI adapters. 32 */ 33 #ifndef _ISPMBOX_H 34 #define _ISPMBOX_H 35 36 /* 37 * Mailbox Command Opcodes 38 */ 39 #define MBOX_NO_OP 0x0000 40 #define MBOX_LOAD_RAM 0x0001 41 #define MBOX_EXEC_FIRMWARE 0x0002 42 #define MBOX_DUMP_RAM 0x0003 43 #define MBOX_WRITE_RAM_WORD 0x0004 44 #define MBOX_READ_RAM_WORD 0x0005 45 #define MBOX_MAILBOX_REG_TEST 0x0006 46 #define MBOX_VERIFY_CHECKSUM 0x0007 47 #define MBOX_ABOUT_FIRMWARE 0x0008 48 #define MBOX_LOAD_RISC_RAM_2100 0x0009 49 /* a */ 50 #define MBOX_LOAD_RISC_RAM 0x000b 51 #define MBOX_DUMP_RISC_RAM 0x000c 52 #define MBOX_WRITE_RAM_WORD_EXTENDED 0x000d 53 #define MBOX_CHECK_FIRMWARE 0x000e 54 #define MBOX_READ_RAM_WORD_EXTENDED 0x000f 55 #define MBOX_INIT_REQ_QUEUE 0x0010 56 #define MBOX_INIT_RES_QUEUE 0x0011 57 #define MBOX_EXECUTE_IOCB 0x0012 58 #define MBOX_WAKE_UP 0x0013 59 #define MBOX_STOP_FIRMWARE 0x0014 60 #define MBOX_ABORT 0x0015 61 #define MBOX_ABORT_DEVICE 0x0016 62 #define MBOX_ABORT_TARGET 0x0017 63 #define MBOX_BUS_RESET 0x0018 64 #define MBOX_STOP_QUEUE 0x0019 65 #define MBOX_START_QUEUE 0x001a 66 #define MBOX_SINGLE_STEP_QUEUE 0x001b 67 #define MBOX_ABORT_QUEUE 0x001c 68 #define MBOX_GET_DEV_QUEUE_STATUS 0x001d 69 /* 1e */ 70 #define MBOX_GET_FIRMWARE_STATUS 0x001f 71 #define MBOX_GET_INIT_SCSI_ID 0x0020 72 #define MBOX_GET_SELECT_TIMEOUT 0x0021 73 #define MBOX_GET_RETRY_COUNT 0x0022 74 #define MBOX_GET_TAG_AGE_LIMIT 0x0023 75 #define MBOX_GET_CLOCK_RATE 0x0024 76 #define MBOX_GET_ACT_NEG_STATE 0x0025 77 #define MBOX_GET_ASYNC_DATA_SETUP_TIME 0x0026 78 #define MBOX_GET_SBUS_PARAMS 0x0027 79 #define MBOX_GET_PCI_PARAMS MBOX_GET_SBUS_PARAMS 80 #define MBOX_GET_TARGET_PARAMS 0x0028 81 #define MBOX_GET_DEV_QUEUE_PARAMS 0x0029 82 #define MBOX_GET_RESET_DELAY_PARAMS 0x002a 83 /* 2b */ 84 /* 2c */ 85 /* 2d */ 86 /* 2e */ 87 /* 2f */ 88 #define MBOX_SET_INIT_SCSI_ID 0x0030 89 #define MBOX_SET_SELECT_TIMEOUT 0x0031 90 #define MBOX_SET_RETRY_COUNT 0x0032 91 #define MBOX_SET_TAG_AGE_LIMIT 0x0033 92 #define MBOX_SET_CLOCK_RATE 0x0034 93 #define MBOX_SET_ACT_NEG_STATE 0x0035 94 #define MBOX_SET_ASYNC_DATA_SETUP_TIME 0x0036 95 #define MBOX_SET_SBUS_CONTROL_PARAMS 0x0037 96 #define MBOX_SET_PCI_PARAMETERS 0x0037 97 #define MBOX_SET_TARGET_PARAMS 0x0038 98 #define MBOX_SET_DEV_QUEUE_PARAMS 0x0039 99 #define MBOX_SET_RESET_DELAY_PARAMS 0x003a 100 /* 3b */ 101 /* 3c */ 102 /* 3d */ 103 /* 3e */ 104 /* 3f */ 105 #define MBOX_RETURN_BIOS_BLOCK_ADDR 0x0040 106 #define MBOX_WRITE_FOUR_RAM_WORDS 0x0041 107 #define MBOX_EXEC_BIOS_IOCB 0x0042 108 #define MBOX_SET_FW_FEATURES 0x004a 109 #define MBOX_GET_FW_FEATURES 0x004b 110 #define FW_FEATURE_FAST_POST 0x1 111 #define FW_FEATURE_LVD_NOTIFY 0x2 112 #define FW_FEATURE_RIO_32BIT 0x4 113 #define FW_FEATURE_RIO_16BIT 0x8 114 115 #define MBOX_INIT_REQ_QUEUE_A64 0x0052 116 #define MBOX_INIT_RES_QUEUE_A64 0x0053 117 118 #define MBOX_ENABLE_TARGET_MODE 0x0055 119 #define ENABLE_TARGET_FLAG 0x8000 120 #define ENABLE_TQING_FLAG 0x0004 121 #define ENABLE_MANDATORY_DISC 0x0002 122 #define MBOX_GET_TARGET_STATUS 0x0056 123 124 /* These are for the ISP2X00 FC cards */ 125 #define MBOX_LOAD_FLASH_FIRMWARE 0x0003 126 #define MBOX_WRITE_FC_SERDES_REG 0x0003 /* FC only */ 127 #define MBOX_READ_FC_SERDES_REG 0x0004 /* FC only */ 128 #define MBOX_GET_IO_STATUS 0x0012 129 #define MBOX_SET_TRANSMIT_PARAMS 0x0019 130 #define MBOX_SET_PORT_PARAMS 0x001a 131 #define MBOX_LOAD_OP_FW_PARAMS 0x001b 132 #define MBOX_INIT_MULTIPLE_QUEUE 0x001f 133 #define MBOX_GET_LOOP_ID 0x0020 134 /* for 24XX cards, outgoing mailbox 7 has these values for F or FL topologies */ 135 #define ISP24XX_INORDER 0x0100 136 #define ISP24XX_NPIV_SAN 0x0400 137 #define ISP24XX_VSAN_SAN 0x1000 138 #define ISP24XX_FC_SP_SAN 0x2000 139 #define MBOX_GET_TIMEOUT_PARAMS 0x0022 140 #define MBOX_GET_FIRMWARE_OPTIONS 0x0028 141 #define MBOX_GENERATE_SYSTEM_ERROR 0x002a 142 #define MBOX_WRITE_SFP 0x0030 143 #define MBOX_READ_SFP 0x0031 144 #define MBOX_SET_TIMEOUT_PARAMS 0x0032 145 #define MBOX_SET_FIRMWARE_OPTIONS 0x0038 146 #define MBOX_GET_SET_FC_LED_CONF 0x003b 147 #define MBOX_RESTART_NIC_FIRMWARE 0x003d /* FCoE only */ 148 #define MBOX_ACCESS_CONTROL 0x003e 149 #define MBOX_LOOP_PORT_BYPASS 0x0040 /* FC only */ 150 #define MBOX_LOOP_PORT_ENABLE 0x0041 /* FC only */ 151 #define MBOX_GET_RESOURCE_COUNT 0x0042 152 #define MBOX_REQUEST_OFFLINE_MODE 0x0043 153 #define MBOX_DIAGNOSTIC_ECHO_TEST 0x0044 154 #define MBOX_DIAGNOSTIC_LOOPBACK 0x0045 155 #define MBOX_ENHANCED_GET_PDB 0x0047 156 #define MBOX_INIT_FIRMWARE_MULTI_ID 0x0048 /* 2400 only */ 157 #define MBOX_GET_VP_DATABASE 0x0049 /* 2400 only */ 158 #define MBOX_GET_VP_DATABASE_ENTRY 0x004a /* 2400 only */ 159 #define MBOX_GET_FCF_LIST 0x0050 /* FCoE only */ 160 #define MBOX_GET_DCBX_PARAMETERS 0x0051 /* FCoE only */ 161 #define MBOX_HOST_MEMORY_COPY 0x0053 162 #define MBOX_EXEC_COMMAND_IOCB_A64 0x0054 163 #define MBOX_SEND_RNID 0x0057 164 #define MBOX_SET_PARAMETERS 0x0059 165 #define MBOX_GET_PARAMETERS 0x005a 166 #define MBOX_DRIVER_HEARTBEAT 0x005B /* FC only */ 167 #define MBOX_FW_HEARTBEAT 0x005C 168 #define MBOX_GET_SET_DATA_RATE 0x005D /* >=23XX only */ 169 #define MBGSD_GET_RATE 0 170 #define MBGSD_SET_RATE 1 171 #define MBGSD_SET_RATE_NOW 2 /* 24XX only */ 172 #define MBGSD_1GB 0x00 173 #define MBGSD_2GB 0x01 174 #define MBGSD_AUTO 0x02 175 #define MBGSD_4GB 0x03 /* 24XX only */ 176 #define MBGSD_8GB 0x04 /* 25XX only */ 177 #define MBGSD_16GB 0x05 /* 26XX only */ 178 #define MBGSD_10GB 0x13 /* 26XX only */ 179 #define MBOX_SEND_RNFT 0x005e 180 #define MBOX_INIT_FIRMWARE 0x0060 181 #define MBOX_GET_INIT_CONTROL_BLOCK 0x0061 182 #define MBOX_INIT_LIP 0x0062 183 #define MBOX_GET_FC_AL_POSITION_MAP 0x0063 184 #define MBOX_GET_PORT_DB 0x0064 185 #define MBOX_CLEAR_ACA 0x0065 186 #define MBOX_TARGET_RESET 0x0066 187 #define MBOX_CLEAR_TASK_SET 0x0067 188 #define MBOX_ABORT_TASK_SET 0x0068 189 #define MBOX_GET_FW_STATE 0x0069 190 #define MBOX_GET_PORT_NAME 0x006A 191 #define MBOX_GET_LINK_STATUS 0x006B 192 #define MBOX_INIT_LIP_RESET 0x006C 193 #define MBOX_GET_LINK_STAT_PR_DATA_CNT 0x006D 194 #define MBOX_SEND_SNS 0x006E 195 #define MBOX_FABRIC_LOGIN 0x006F 196 #define MBOX_SEND_CHANGE_REQUEST 0x0070 197 #define MBOX_FABRIC_LOGOUT 0x0071 198 #define MBOX_INIT_LIP_LOGIN 0x0072 199 #define MBOX_GET_PORT_NODE_NAME_LIST 0x0075 200 #define MBOX_SET_VENDOR_ID 0x0076 201 #define MBOX_GET_XGMAC_STATS 0x007a 202 #define MBOX_GET_ID_LIST 0x007C 203 #define MBOX_SEND_LFA 0x007d 204 #define MBOX_LUN_RESET 0x007E 205 206 #define ISP2100_SET_PCI_PARAM 0x00ff 207 208 #define MBOX_BUSY 0x04 209 210 /* 211 * Mailbox Command Complete Status Codes 212 */ 213 #define MBOX_COMMAND_COMPLETE 0x4000 214 #define MBOX_INVALID_COMMAND 0x4001 215 #define MBOX_HOST_INTERFACE_ERROR 0x4002 216 #define MBOX_TEST_FAILED 0x4003 217 #define MBOX_COMMAND_ERROR 0x4005 218 #define MBOX_COMMAND_PARAM_ERROR 0x4006 219 #define MBOX_PORT_ID_USED 0x4007 220 #define MBOX_LOOP_ID_USED 0x4008 221 #define MBOX_ALL_IDS_USED 0x4009 222 #define MBOX_NOT_LOGGED_IN 0x400A 223 #define MBOX_LINK_DOWN_ERROR 0x400B 224 #define MBOX_LOOPBACK_ERROR 0x400C 225 #define MBOX_CHECKSUM_ERROR 0x4010 226 #define MBOX_INVALID_PRODUCT_KEY 0x4020 227 /* pseudo mailbox completion codes */ 228 #define MBOX_REGS_BUSY 0x6000 /* registers in use */ 229 #define MBOX_TIMEOUT 0x6001 /* command timed out */ 230 231 #define MBLOGALL 0xffffffff 232 #define MBLOGNONE 0x00000000 233 #define MBLOGMASK(x) (1 << (((x) - 1) & 0x1f)) 234 235 /* 236 * Asynchronous event status codes 237 */ 238 #define ASYNC_BUS_RESET 0x8001 239 #define ASYNC_SYSTEM_ERROR 0x8002 240 #define ASYNC_RQS_XFER_ERR 0x8003 241 #define ASYNC_RSP_XFER_ERR 0x8004 242 #define ASYNC_QWAKEUP 0x8005 243 #define ASYNC_TIMEOUT_RESET 0x8006 244 #define ASYNC_DEVICE_RESET 0x8007 245 #define ASYNC_EXTMSG_UNDERRUN 0x800A 246 #define ASYNC_SCAM_INT 0x800B 247 #define ASYNC_HUNG_SCSI 0x800C 248 #define ASYNC_KILLED_BUS 0x800D 249 #define ASYNC_BUS_TRANSIT 0x800E /* LVD -> HVD, eg. */ 250 #define ASYNC_LIP_OCCURRED 0x8010 /* FC only */ 251 #define ASYNC_LOOP_UP 0x8011 252 #define ASYNC_LOOP_DOWN 0x8012 253 #define ASYNC_LOOP_RESET 0x8013 /* FC only */ 254 #define ASYNC_PDB_CHANGED 0x8014 255 #define ASYNC_CHANGE_NOTIFY 0x8015 256 #define ASYNC_LIP_NOS_OLS_RECV 0x8016 /* FC only */ 257 #define ASYNC_LIP_ERROR 0x8017 /* FC only */ 258 #define ASYNC_AUTO_PLOGI_RJT 0x8018 259 #define ASYNC_SECURITY_UPDATE 0x801B 260 #define ASYNC_CMD_CMPLT 0x8020 261 #define ASYNC_CTIO_DONE 0x8021 262 #define ASYNC_RIO32_1 0x8021 263 #define ASYNC_RIO32_2 0x8022 264 #define ASYNC_IP_XMIT_DONE 0x8022 265 #define ASYNC_IP_RECV_DONE 0x8023 266 #define ASYNC_IP_BROADCAST 0x8024 267 #define ASYNC_IP_RCVQ_LOW 0x8025 268 #define ASYNC_IP_RCVQ_EMPTY 0x8026 269 #define ASYNC_IP_RECV_DONE_ALIGNED 0x8027 270 #define ASYNC_ERR_LOGGING_DISABLED 0x8029 271 #define ASYNC_PTPMODE 0x8030 /* FC only */ 272 #define ASYNC_RIO16_1 0x8031 273 #define ASYNC_RIO16_2 0x8032 274 #define ASYNC_RIO16_3 0x8033 275 #define ASYNC_RIO16_4 0x8034 276 #define ASYNC_RIO16_5 0x8035 277 #define ASYNC_CONNMODE 0x8036 278 #define ISP_CONN_LOOP 1 279 #define ISP_CONN_PTP 2 280 #define ISP_CONN_BADLIP 3 281 #define ISP_CONN_FATAL 4 282 #define ISP_CONN_LOOPBACK 5 283 #define ASYNC_P2P_INIT_ERR 0x8037 284 #define ASYNC_RIOZIO_STALL 0x8040 /* there's a RIO/ZIO entry that hasn't been serviced */ 285 #define ASYNC_RIO32_2_2200 0x8042 /* same as ASYNC_RIO32_2, but for 2100/2200 */ 286 #define ASYNC_RCV_ERR 0x8048 287 /* 288 * 2.01.31 2200 Only. Need Bit 13 in Mailbox 1 for Set Firmware Options 289 * mailbox command to enable this. 290 */ 291 #define ASYNC_QFULL_SENT 0x8049 292 #define ASYNC_RJT_SENT 0x8049 /* 24XX only */ 293 #define ASYNC_SEL_CLASS2_P_RJT_SENT 0x804f 294 #define ASYNC_FW_RESTART_COMPLETE 0x8060 295 #define ASYNC_TEMPERATURE_ALERT 0x8070 296 #define ASYNC_INTER_DRIVER_COMP 0x8100 /* FCoE only */ 297 #define ASYNC_INTER_DRIVER_NOTIFY 0x8101 /* FCoE only */ 298 #define ASYNC_INTER_DRIVER_TIME_EXT 0x8102 /* FCoE only */ 299 #define ASYNC_NIC_FW_STATE_CHANGE 0x8200 /* FCoE only */ 300 #define ASYNC_AUTOLOAD_FW_COMPLETE 0x8400 301 #define ASYNC_AUTOLOAD_FW_FAILURE 0x8401 302 303 /* 304 * Firmware Options. There are a lot of them. 305 * 306 * IFCOPTN - ISP Fibre Channel Option Word N 307 */ 308 #define IFCOPT1_EQFQASYNC (1 << 13) /* enable QFULL notification */ 309 #define IFCOPT1_EAABSRCVD (1 << 12) 310 #define IFCOPT1_RJTASYNC (1 << 11) /* enable 8018 notification */ 311 #define IFCOPT1_ENAPURE (1 << 10) 312 #define IFCOPT1_ENA8017 (1 << 7) 313 #define IFCOPT1_DISGPIO67 (1 << 6) 314 #define IFCOPT1_LIPLOSSIMM (1 << 5) 315 #define IFCOPT1_DISF7SWTCH (1 << 4) 316 #define IFCOPT1_CTIO_RETRY (1 << 3) 317 #define IFCOPT1_LIPASYNC (1 << 1) 318 #define IFCOPT1_LIPF8 (1 << 0) 319 320 #define IFCOPT2_LOOPBACK (1 << 1) 321 #define IFCOPT2_ATIO3_ONLY (1 << 0) 322 323 #define IFCOPT3_NOPRLI (1 << 4) /* disable automatic sending of PRLI on local loops */ 324 #define IFCOPT3_RNDASYNC (1 << 1) 325 326 /* 327 * All IOCB Queue entries are this size 328 */ 329 #define QENTRY_LEN 64 330 331 /* 332 * Command Structure Definitions 333 */ 334 335 typedef struct { 336 uint32_t ds_base; 337 uint32_t ds_count; 338 } ispds_t; 339 340 typedef struct { 341 uint32_t ds_base; 342 uint32_t ds_basehi; 343 uint32_t ds_count; 344 } ispds64_t; 345 346 #define DSTYPE_32BIT 0 347 #define DSTYPE_64BIT 1 348 typedef struct { 349 uint16_t ds_type; /* 0-> ispds_t, 1-> ispds64_t */ 350 uint32_t ds_segment; /* unused */ 351 uint32_t ds_base; /* 32 bit address of DSD list */ 352 } ispdslist_t; 353 354 355 typedef struct { 356 uint8_t rqs_entry_type; 357 uint8_t rqs_entry_count; 358 uint8_t rqs_seqno; 359 uint8_t rqs_flags; 360 } isphdr_t; 361 362 /* RQS Flag definitions */ 363 #define RQSFLAG_CONTINUATION 0x01 364 #define RQSFLAG_FULL 0x02 365 #define RQSFLAG_BADHEADER 0x04 366 #define RQSFLAG_BADPACKET 0x08 367 #define RQSFLAG_BADCOUNT 0x10 368 #define RQSFLAG_BADORDER 0x20 369 #define RQSFLAG_MASK 0x3f 370 371 /* RQS entry_type definitions */ 372 #define RQSTYPE_REQUEST 0x01 373 #define RQSTYPE_DATASEG 0x02 374 #define RQSTYPE_RESPONSE 0x03 375 #define RQSTYPE_MARKER 0x04 376 #define RQSTYPE_CMDONLY 0x05 377 #define RQSTYPE_ATIO 0x06 /* Target Mode */ 378 #define RQSTYPE_CTIO 0x07 /* Target Mode */ 379 #define RQSTYPE_SCAM 0x08 380 #define RQSTYPE_A64 0x09 381 #define RQSTYPE_A64_CONT 0x0a 382 #define RQSTYPE_ENABLE_LUN 0x0b /* Target Mode */ 383 #define RQSTYPE_MODIFY_LUN 0x0c /* Target Mode */ 384 #define RQSTYPE_NOTIFY 0x0d /* Target Mode */ 385 #define RQSTYPE_NOTIFY_ACK 0x0e /* Target Mode */ 386 #define RQSTYPE_CTIO1 0x0f /* Target Mode */ 387 #define RQSTYPE_STATUS_CONT 0x10 388 #define RQSTYPE_T2RQS 0x11 389 #define RQSTYPE_CTIO7 0x12 390 #define RQSTYPE_IP_XMIT 0x13 391 #define RQSTYPE_TSK_MGMT 0x14 392 #define RQSTYPE_T4RQS 0x15 393 #define RQSTYPE_ATIO2 0x16 /* Target Mode */ 394 #define RQSTYPE_CTIO2 0x17 /* Target Mode */ 395 #define RQSTYPE_T7RQS 0x18 396 #define RQSTYPE_T3RQS 0x19 397 #define RQSTYPE_IP_XMIT_64 0x1b 398 #define RQSTYPE_CTIO4 0x1e /* Target Mode */ 399 #define RQSTYPE_CTIO3 0x1f /* Target Mode */ 400 #define RQSTYPE_RIO1 0x21 401 #define RQSTYPE_RIO2 0x22 402 #define RQSTYPE_IP_RECV 0x23 403 #define RQSTYPE_IP_RECV_CONT 0x24 404 #define RQSTYPE_CT_PASSTHRU 0x29 405 #define RQSTYPE_MS_PASSTHRU 0x29 406 #define RQSTYPE_VP_CTRL 0x30 /* 24XX only */ 407 #define RQSTYPE_VP_MODIFY 0x31 /* 24XX only */ 408 #define RQSTYPE_RPT_ID_ACQ 0x32 /* 24XX only */ 409 #define RQSTYPE_ABORT_IO 0x33 410 #define RQSTYPE_T6RQS 0x48 411 #define RQSTYPE_LOGIN 0x52 412 #define RQSTYPE_ABTS_RCVD 0x54 /* 24XX only */ 413 #define RQSTYPE_ABTS_RSP 0x55 /* 24XX only */ 414 415 416 #define ISP_RQDSEG 4 417 typedef struct { 418 isphdr_t req_header; 419 uint32_t req_handle; 420 uint8_t req_lun_trn; 421 uint8_t req_target; 422 uint16_t req_cdblen; 423 uint16_t req_flags; 424 uint16_t req_reserved; 425 uint16_t req_time; 426 uint16_t req_seg_count; 427 uint8_t req_cdb[12]; 428 ispds_t req_dataseg[ISP_RQDSEG]; 429 } ispreq_t; 430 #define ISP_RQDSEG_A64 2 431 432 typedef struct { 433 isphdr_t mrk_header; 434 uint32_t mrk_handle; 435 uint8_t mrk_reserved0; 436 uint8_t mrk_target; 437 uint16_t mrk_modifier; 438 uint16_t mrk_flags; 439 uint16_t mrk_lun; 440 uint8_t mrk_reserved1[48]; 441 } isp_marker_t; 442 443 typedef struct { 444 isphdr_t mrk_header; 445 uint32_t mrk_handle; 446 uint16_t mrk_nphdl; 447 uint8_t mrk_modifier; 448 uint8_t mrk_reserved0; 449 uint8_t mrk_reserved1; 450 uint8_t mrk_vphdl; 451 uint16_t mrk_reserved2; 452 uint8_t mrk_lun[8]; 453 uint8_t mrk_reserved3[40]; 454 } isp_marker_24xx_t; 455 456 457 #define SYNC_DEVICE 0 458 #define SYNC_TARGET 1 459 #define SYNC_ALL 2 460 #define SYNC_LIP 3 461 462 #define ISP_RQDSEG_T2 3 463 typedef struct { 464 isphdr_t req_header; 465 uint32_t req_handle; 466 uint8_t req_lun_trn; 467 uint8_t req_target; 468 uint16_t req_scclun; 469 uint16_t req_flags; 470 uint8_t req_crn; 471 uint8_t req_reserved; 472 uint16_t req_time; 473 uint16_t req_seg_count; 474 uint8_t req_cdb[16]; 475 uint32_t req_totalcnt; 476 ispds_t req_dataseg[ISP_RQDSEG_T2]; 477 } ispreqt2_t; 478 479 typedef struct { 480 isphdr_t req_header; 481 uint32_t req_handle; 482 uint16_t req_target; 483 uint16_t req_scclun; 484 uint16_t req_flags; 485 uint8_t req_crn; 486 uint8_t req_reserved; 487 uint16_t req_time; 488 uint16_t req_seg_count; 489 uint8_t req_cdb[16]; 490 uint32_t req_totalcnt; 491 ispds_t req_dataseg[ISP_RQDSEG_T2]; 492 } ispreqt2e_t; 493 494 #define ISP_RQDSEG_T3 2 495 typedef struct { 496 isphdr_t req_header; 497 uint32_t req_handle; 498 uint8_t req_lun_trn; 499 uint8_t req_target; 500 uint16_t req_scclun; 501 uint16_t req_flags; 502 uint8_t req_crn; 503 uint8_t req_reserved; 504 uint16_t req_time; 505 uint16_t req_seg_count; 506 uint8_t req_cdb[16]; 507 uint32_t req_totalcnt; 508 ispds64_t req_dataseg[ISP_RQDSEG_T3]; 509 } ispreqt3_t; 510 #define ispreq64_t ispreqt3_t /* same as.... */ 511 512 typedef struct { 513 isphdr_t req_header; 514 uint32_t req_handle; 515 uint16_t req_target; 516 uint16_t req_scclun; 517 uint16_t req_flags; 518 uint8_t req_crn; 519 uint8_t req_reserved; 520 uint16_t req_time; 521 uint16_t req_seg_count; 522 uint8_t req_cdb[16]; 523 uint32_t req_totalcnt; 524 ispds64_t req_dataseg[ISP_RQDSEG_T3]; 525 } ispreqt3e_t; 526 527 /* req_flag values */ 528 #define REQFLAG_NODISCON 0x0001 529 #define REQFLAG_HTAG 0x0002 530 #define REQFLAG_OTAG 0x0004 531 #define REQFLAG_STAG 0x0008 532 #define REQFLAG_TARGET_RTN 0x0010 533 534 #define REQFLAG_NODATA 0x0000 535 #define REQFLAG_DATA_IN 0x0020 536 #define REQFLAG_DATA_OUT 0x0040 537 #define REQFLAG_DATA_UNKNOWN 0x0060 538 539 #define REQFLAG_DISARQ 0x0100 540 #define REQFLAG_FRC_ASYNC 0x0200 541 #define REQFLAG_FRC_SYNC 0x0400 542 #define REQFLAG_FRC_WIDE 0x0800 543 #define REQFLAG_NOPARITY 0x1000 544 #define REQFLAG_STOPQ 0x2000 545 #define REQFLAG_XTRASNS 0x4000 546 #define REQFLAG_PRIORITY 0x8000 547 548 typedef struct { 549 isphdr_t req_header; 550 uint32_t req_handle; 551 uint8_t req_lun_trn; 552 uint8_t req_target; 553 uint16_t req_cdblen; 554 uint16_t req_flags; 555 uint16_t req_reserved; 556 uint16_t req_time; 557 uint16_t req_seg_count; 558 uint8_t req_cdb[44]; 559 } ispextreq_t; 560 561 562 /* 563 * ISP24XX structures 564 */ 565 typedef struct { 566 isphdr_t req_header; 567 uint32_t req_handle; 568 uint16_t req_nphdl; 569 uint16_t req_time; 570 uint16_t req_seg_count; 571 uint16_t req_reserved; 572 uint8_t req_lun[8]; 573 uint8_t req_alen_datadir; 574 uint8_t req_task_management; 575 uint8_t req_task_attribute; 576 uint8_t req_crn; 577 uint8_t req_cdb[16]; 578 uint32_t req_dl; 579 uint16_t req_tidlo; 580 uint8_t req_tidhi; 581 uint8_t req_vpidx; 582 ispds64_t req_dataseg; 583 } ispreqt7_t; 584 585 /* Task Management Request Function */ 586 typedef struct { 587 isphdr_t tmf_header; 588 uint32_t tmf_handle; 589 uint16_t tmf_nphdl; 590 uint8_t tmf_reserved0[2]; 591 uint16_t tmf_delay; 592 uint16_t tmf_timeout; 593 uint8_t tmf_lun[8]; 594 uint32_t tmf_flags; 595 uint8_t tmf_reserved1[20]; 596 uint16_t tmf_tidlo; 597 uint8_t tmf_tidhi; 598 uint8_t tmf_vpidx; 599 uint8_t tmf_reserved2[12]; 600 } isp24xx_tmf_t; 601 602 #define ISP24XX_TMF_NOSEND 0x80000000 603 604 #define ISP24XX_TMF_LUN_RESET 0x00000010 605 #define ISP24XX_TMF_ABORT_TASK_SET 0x00000008 606 #define ISP24XX_TMF_CLEAR_TASK_SET 0x00000004 607 #define ISP24XX_TMF_TARGET_RESET 0x00000002 608 #define ISP24XX_TMF_CLEAR_ACA 0x00000001 609 610 /* I/O Abort Structure */ 611 typedef struct { 612 isphdr_t abrt_header; 613 uint32_t abrt_handle; 614 uint16_t abrt_nphdl; 615 uint16_t abrt_options; 616 uint32_t abrt_cmd_handle; 617 uint16_t abrt_queue_number; 618 uint8_t abrt_reserved[30]; 619 uint16_t abrt_tidlo; 620 uint8_t abrt_tidhi; 621 uint8_t abrt_vpidx; 622 uint8_t abrt_reserved1[12]; 623 } isp24xx_abrt_t; 624 625 #define ISP24XX_ABRT_NOSEND 0x01 /* don't actually send ABTS */ 626 #define ISP24XX_ABRT_OKAY 0x00 /* in nphdl on return */ 627 #define ISP24XX_ABRT_ENXIO 0x31 /* in nphdl on return */ 628 629 #define ISP_CDSEG 7 630 typedef struct { 631 isphdr_t req_header; 632 uint32_t req_reserved; 633 ispds_t req_dataseg[ISP_CDSEG]; 634 } ispcontreq_t; 635 636 #define ISP_CDSEG64 5 637 typedef struct { 638 isphdr_t req_header; 639 ispds64_t req_dataseg[ISP_CDSEG64]; 640 } ispcontreq64_t; 641 642 typedef struct { 643 isphdr_t req_header; 644 uint32_t req_handle; 645 uint16_t req_scsi_status; 646 uint16_t req_completion_status; 647 uint16_t req_state_flags; 648 uint16_t req_status_flags; 649 uint16_t req_time; 650 #define req_response_len req_time /* FC only */ 651 uint16_t req_sense_len; 652 uint32_t req_resid; 653 uint8_t req_response[8]; /* FC only */ 654 uint8_t req_sense_data[32]; 655 } ispstatusreq_t; 656 657 /* 658 * Status Continuation 659 */ 660 typedef struct { 661 isphdr_t req_header; 662 uint8_t req_sense_data[60]; 663 } ispstatus_cont_t; 664 665 /* 666 * 24XX Type 0 status 667 */ 668 typedef struct { 669 isphdr_t req_header; 670 uint32_t req_handle; 671 uint16_t req_completion_status; 672 uint16_t req_oxid; 673 uint32_t req_resid; 674 uint16_t req_reserved0; 675 uint16_t req_state_flags; 676 uint16_t req_retry_delay; /* aka Status Qualifier */ 677 uint16_t req_scsi_status; 678 uint32_t req_fcp_residual; 679 uint32_t req_sense_len; 680 uint32_t req_response_len; 681 uint8_t req_rsp_sense[28]; 682 } isp24xx_statusreq_t; 683 684 /* 685 * For Qlogic 2X00, the high order byte of SCSI status has 686 * additional meaning. 687 */ 688 #define RQCS_CR 0x1000 /* Confirmation Request */ 689 #define RQCS_RU 0x0800 /* Residual Under */ 690 #define RQCS_RO 0x0400 /* Residual Over */ 691 #define RQCS_RESID (RQCS_RU|RQCS_RO) 692 #define RQCS_SV 0x0200 /* Sense Length Valid */ 693 #define RQCS_RV 0x0100 /* FCP Response Length Valid */ 694 695 /* 696 * CT Passthru IOCB 697 */ 698 typedef struct { 699 isphdr_t ctp_header; 700 uint32_t ctp_handle; 701 uint16_t ctp_status; 702 uint16_t ctp_nphdl; /* n-port handle */ 703 uint16_t ctp_cmd_cnt; /* Command DSD count */ 704 uint8_t ctp_vpidx; 705 uint8_t ctp_reserved0; 706 uint16_t ctp_time; 707 uint16_t ctp_reserved1; 708 uint16_t ctp_rsp_cnt; /* Response DSD count */ 709 uint16_t ctp_reserved2[5]; 710 uint32_t ctp_rsp_bcnt; /* Response byte count */ 711 uint32_t ctp_cmd_bcnt; /* Command byte count */ 712 ispds64_t ctp_dataseg[2]; 713 } isp_ct_pt_t; 714 715 /* 716 * MS Passthru IOCB 717 */ 718 typedef struct { 719 isphdr_t ms_header; 720 uint32_t ms_handle; 721 uint16_t ms_nphdl; /* handle in high byte for !2k f/w */ 722 uint16_t ms_status; 723 uint16_t ms_flags; 724 uint16_t ms_reserved1; /* low 8 bits */ 725 uint16_t ms_time; 726 uint16_t ms_cmd_cnt; /* Command DSD count */ 727 uint16_t ms_tot_cnt; /* Total DSD Count */ 728 uint8_t ms_type; /* MS type */ 729 uint8_t ms_r_ctl; /* R_CTL */ 730 uint16_t ms_rxid; /* RX_ID */ 731 uint16_t ms_reserved2; 732 uint32_t ms_handle2; 733 uint32_t ms_rsp_bcnt; /* Response byte count */ 734 uint32_t ms_cmd_bcnt; /* Command byte count */ 735 ispds64_t ms_dataseg[2]; 736 } isp_ms_t; 737 738 /* 739 * Completion Status Codes. 740 */ 741 #define RQCS_COMPLETE 0x0000 742 #define RQCS_DMA_ERROR 0x0002 743 #define RQCS_RESET_OCCURRED 0x0004 744 #define RQCS_ABORTED 0x0005 745 #define RQCS_TIMEOUT 0x0006 746 #define RQCS_DATA_OVERRUN 0x0007 747 #define RQCS_DATA_UNDERRUN 0x0015 748 #define RQCS_QUEUE_FULL 0x001C 749 750 /* 1X00 Only Completion Codes */ 751 #define RQCS_INCOMPLETE 0x0001 752 #define RQCS_TRANSPORT_ERROR 0x0003 753 #define RQCS_COMMAND_OVERRUN 0x0008 754 #define RQCS_STATUS_OVERRUN 0x0009 755 #define RQCS_BAD_MESSAGE 0x000a 756 #define RQCS_NO_MESSAGE_OUT 0x000b 757 #define RQCS_EXT_ID_FAILED 0x000c 758 #define RQCS_IDE_MSG_FAILED 0x000d 759 #define RQCS_ABORT_MSG_FAILED 0x000e 760 #define RQCS_REJECT_MSG_FAILED 0x000f 761 #define RQCS_NOP_MSG_FAILED 0x0010 762 #define RQCS_PARITY_ERROR_MSG_FAILED 0x0011 763 #define RQCS_DEVICE_RESET_MSG_FAILED 0x0012 764 #define RQCS_ID_MSG_FAILED 0x0013 765 #define RQCS_UNEXP_BUS_FREE 0x0014 766 #define RQCS_XACT_ERR1 0x0018 767 #define RQCS_XACT_ERR2 0x0019 768 #define RQCS_XACT_ERR3 0x001A 769 #define RQCS_BAD_ENTRY 0x001B 770 #define RQCS_PHASE_SKIPPED 0x001D 771 #define RQCS_ARQS_FAILED 0x001E 772 #define RQCS_WIDE_FAILED 0x001F 773 #define RQCS_SYNCXFER_FAILED 0x0020 774 #define RQCS_LVD_BUSERR 0x0021 775 776 /* 2X00 Only Completion Codes */ 777 #define RQCS_PORT_UNAVAILABLE 0x0028 778 #define RQCS_PORT_LOGGED_OUT 0x0029 779 #define RQCS_PORT_CHANGED 0x002A 780 #define RQCS_PORT_BUSY 0x002B 781 782 /* 24XX Only Completion Codes */ 783 #define RQCS_24XX_DRE 0x0011 /* data reassembly error */ 784 #define RQCS_24XX_TABORT 0x0013 /* aborted by target */ 785 #define RQCS_24XX_ENOMEM 0x002C /* f/w resource unavailable */ 786 #define RQCS_24XX_TMO 0x0030 /* task management overrun */ 787 788 789 /* 790 * 1X00 specific State Flags 791 */ 792 #define RQSF_GOT_BUS 0x0100 793 #define RQSF_GOT_TARGET 0x0200 794 #define RQSF_SENT_CDB 0x0400 795 #define RQSF_XFRD_DATA 0x0800 796 #define RQSF_GOT_STATUS 0x1000 797 #define RQSF_GOT_SENSE 0x2000 798 #define RQSF_XFER_COMPLETE 0x4000 799 800 /* 801 * 2X00 specific State Flags 802 * (same as 1X00 except RQSF_GOT_BUS/RQSF_GOT_TARGET are not available) 803 */ 804 #define RQSF_DATA_IN 0x0020 805 #define RQSF_DATA_OUT 0x0040 806 #define RQSF_STAG 0x0008 807 #define RQSF_OTAG 0x0004 808 #define RQSF_HTAG 0x0002 809 /* 810 * 1X00 Status Flags 811 */ 812 #define RQSTF_DISCONNECT 0x0001 813 #define RQSTF_SYNCHRONOUS 0x0002 814 #define RQSTF_PARITY_ERROR 0x0004 815 #define RQSTF_BUS_RESET 0x0008 816 #define RQSTF_DEVICE_RESET 0x0010 817 #define RQSTF_ABORTED 0x0020 818 #define RQSTF_TIMEOUT 0x0040 819 #define RQSTF_NEGOTIATION 0x0080 820 821 /* 822 * 2X00 specific state flags 823 */ 824 /* RQSF_SENT_CDB */ 825 /* RQSF_XFRD_DATA */ 826 /* RQSF_GOT_STATUS */ 827 /* RQSF_XFER_COMPLETE */ 828 829 /* 830 * 2X00 specific status flags 831 */ 832 /* RQSTF_ABORTED */ 833 /* RQSTF_TIMEOUT */ 834 #define RQSTF_DMA_ERROR 0x0080 835 #define RQSTF_LOGOUT 0x2000 836 837 /* 838 * Miscellaneous 839 */ 840 #ifndef ISP_EXEC_THROTTLE 841 #define ISP_EXEC_THROTTLE 16 842 #endif 843 844 /* 845 * About Firmware returns an 'attribute' word in mailbox 6. 846 * These attributes are for 2200 and 2300. 847 */ 848 #define ISP_FW_ATTR_TMODE 0x0001 849 #define ISP_FW_ATTR_SCCLUN 0x0002 850 #define ISP_FW_ATTR_FABRIC 0x0004 851 #define ISP_FW_ATTR_CLASS2 0x0008 852 #define ISP_FW_ATTR_FCTAPE 0x0010 853 #define ISP_FW_ATTR_IP 0x0020 854 #define ISP_FW_ATTR_VI 0x0040 855 #define ISP_FW_ATTR_VI_SOLARIS 0x0080 856 #define ISP_FW_ATTR_2KLOGINS 0x0100 /* just a guess... */ 857 858 /* and these are for the 2400 */ 859 #define ISP2400_FW_ATTR_CLASS2 0x0001 860 #define ISP2400_FW_ATTR_IP 0x0002 861 #define ISP2400_FW_ATTR_MULTIID 0x0004 862 #define ISP2400_FW_ATTR_SB2 0x0008 863 #define ISP2400_FW_ATTR_T10CRC 0x0010 864 #define ISP2400_FW_ATTR_VI 0x0020 865 #define ISP2400_FW_ATTR_MQ 0x0040 866 #define ISP2400_FW_ATTR_MSIX 0x0080 867 #define ISP2400_FW_ATTR_FCOE 0x0800 868 #define ISP2400_FW_ATTR_VP0 0x1000 869 #define ISP2400_FW_ATTR_EXPFW 0x2000 870 #define ISP2400_FW_ATTR_HOTFW 0x4000 871 #define ISP2400_FW_ATTR_EXTNDED 0x8000 872 #define ISP2400_FW_ATTR_EXTVP 0x00010000 873 #define ISP2400_FW_ATTR_VN2VN 0x00040000 874 #define ISP2400_FW_ATTR_EXMOFF 0x00080000 875 #define ISP2400_FW_ATTR_NPMOFF 0x00100000 876 #define ISP2400_FW_ATTR_DIFCHOP 0x00400000 877 #define ISP2400_FW_ATTR_SRIOV 0x02000000 878 #define ISP2400_FW_ATTR_ASICTMP 0x0200000000 879 #define ISP2400_FW_ATTR_ATIOMQ 0x0400000000 880 881 /* 882 * These are either manifestly true or are dependent on f/w attributes 883 */ 884 #define ISP_CAP_TMODE(isp) \ 885 (IS_24XX(isp)? 1 : (isp->isp_fwattr & ISP_FW_ATTR_TMODE)) 886 #define ISP_CAP_SCCFW(isp) \ 887 (IS_24XX(isp)? 1 : (isp->isp_fwattr & ISP_FW_ATTR_SCCLUN)) 888 #define ISP_CAP_2KLOGIN(isp) \ 889 (IS_24XX(isp)? 1 : (isp->isp_fwattr & ISP_FW_ATTR_2KLOGINS)) 890 891 /* 892 * This is only true for 24XX cards with this f/w attribute 893 */ 894 #define ISP_CAP_MULTI_ID(isp) \ 895 (IS_24XX(isp)? (isp->isp_fwattr & ISP2400_FW_ATTR_MULTIID) : 0) 896 #define ISP_GET_VPIDX(isp, tag) \ 897 (ISP_CAP_MULTI_ID(isp) ? tag : 0) 898 #define ISP_CAP_VP0(isp) \ 899 (IS_24XX(isp)? (isp->isp_fwattr & ISP2400_FW_ATTR_VP0) : 0) 900 901 /* 902 * This is true manifestly or is dependent on a f/w attribute 903 * but may or may not actually be *enabled*. In any case, it 904 * is enabled on a per-channel basis. 905 */ 906 #define ISP_CAP_FCTAPE(isp) \ 907 (IS_24XX(isp)? 1 : (isp->isp_fwattr & ISP_FW_ATTR_FCTAPE)) 908 909 #define ISP_FCTAPE_ENABLED(isp, chan) \ 910 (IS_24XX(isp)? (FCPARAM(isp, chan)->isp_xfwoptions & ICB2400_OPT2_FCTAPE) != 0 : (FCPARAM(isp, chan)->isp_xfwoptions & ICBXOPT_FCTAPE) != 0) 911 912 /* 913 * Reduced Interrupt Operation Response Queue Entries 914 */ 915 916 typedef struct { 917 isphdr_t req_header; 918 uint32_t req_handles[15]; 919 } isp_rio1_t; 920 921 typedef struct { 922 isphdr_t req_header; 923 uint16_t req_handles[30]; 924 } isp_rio2_t; 925 926 /* 927 * FC (ISP2100/ISP2200/ISP2300/ISP2400) specific data structures 928 */ 929 930 /* 931 * Initialization Control Block 932 * 933 * Version One (prime) format. 934 */ 935 typedef struct { 936 uint8_t icb_version; 937 uint8_t icb_reserved0; 938 uint16_t icb_fwoptions; 939 uint16_t icb_maxfrmlen; 940 uint16_t icb_maxalloc; 941 uint16_t icb_execthrottle; 942 uint8_t icb_retry_count; 943 uint8_t icb_retry_delay; 944 uint8_t icb_portname[8]; 945 uint16_t icb_hardaddr; 946 uint8_t icb_iqdevtype; 947 uint8_t icb_logintime; 948 uint8_t icb_nodename[8]; 949 uint16_t icb_rqstout; 950 uint16_t icb_rspnsin; 951 uint16_t icb_rqstqlen; 952 uint16_t icb_rsltqlen; 953 uint16_t icb_rqstaddr[4]; 954 uint16_t icb_respaddr[4]; 955 uint16_t icb_lunenables; 956 uint8_t icb_ccnt; 957 uint8_t icb_icnt; 958 uint16_t icb_lunetimeout; 959 uint16_t icb_reserved1; 960 uint16_t icb_xfwoptions; 961 uint8_t icb_racctimer; 962 uint8_t icb_idelaytimer; 963 uint16_t icb_zfwoptions; 964 uint16_t icb_reserved2[13]; 965 } isp_icb_t; 966 967 #define ICB_VERSION1 1 968 969 #define ICBOPT_EXTENDED 0x8000 970 #define ICBOPT_BOTH_WWNS 0x4000 971 #define ICBOPT_FULL_LOGIN 0x2000 972 #define ICBOPT_STOP_ON_QFULL 0x1000 /* 2200/2100 only */ 973 #define ICBOPT_PREV_ADDRESS 0x0800 974 #define ICBOPT_SRCHDOWN 0x0400 975 #define ICBOPT_NOLIP 0x0200 976 #define ICBOPT_PDBCHANGE_AE 0x0100 977 #define ICBOPT_TGT_TYPE 0x0080 978 #define ICBOPT_INI_ADISC 0x0040 979 #define ICBOPT_INI_DISABLE 0x0020 980 #define ICBOPT_TGT_ENABLE 0x0010 981 #define ICBOPT_FAST_POST 0x0008 982 #define ICBOPT_FULL_DUPLEX 0x0004 983 #define ICBOPT_FAIRNESS 0x0002 984 #define ICBOPT_HARD_ADDRESS 0x0001 985 986 #define ICBXOPT_NO_LOGOUT 0x8000 /* no logout on link failure */ 987 #define ICBXOPT_FCTAPE_CCQ 0x4000 /* FC-Tape Command Queueing */ 988 #define ICBXOPT_FCTAPE_CONFIRM 0x2000 989 #define ICBXOPT_FCTAPE 0x1000 990 #define ICBXOPT_CLASS2_ACK0 0x0200 991 #define ICBXOPT_CLASS2 0x0100 992 #define ICBXOPT_NO_PLAY 0x0080 /* don't play if can't get hard addr */ 993 #define ICBXOPT_TOPO_MASK 0x0070 994 #define ICBXOPT_LOOP_ONLY 0x0000 995 #define ICBXOPT_PTP_ONLY 0x0010 996 #define ICBXOPT_LOOP_2_PTP 0x0020 997 #define ICBXOPT_PTP_2_LOOP 0x0030 998 /* 999 * The lower 4 bits of the xfwoptions field are the OPERATION MODE bits. 1000 * RIO is not defined for the 23XX cards (just 2200) 1001 */ 1002 #define ICBXOPT_RIO_OFF 0 1003 #define ICBXOPT_RIO_16BIT 1 1004 #define ICBXOPT_RIO_32BIT 2 1005 #define ICBXOPT_RIO_16BIT_IOCB 3 1006 #define ICBXOPT_RIO_32BIT_IOCB 4 1007 #define ICBXOPT_ZIO 5 1008 #define ICBXOPT_TIMER_MASK 0x7 1009 1010 #define ICBZOPT_RATE_MASK 0xC000 1011 #define ICBZOPT_RATE_1GB 0x0000 1012 #define ICBZOPT_RATE_AUTO 0x8000 1013 #define ICBZOPT_RATE_2GB 0x4000 1014 #define ICBZOPT_50_OHM 0x2000 1015 #define ICBZOPT_NO_LOCAL_PLOGI 0x0080 1016 #define ICBZOPT_ENA_OOF 0x0040 /* out of order frame handling */ 1017 #define ICBZOPT_RSPSZ_MASK 0x0030 1018 #define ICBZOPT_RSPSZ_24 0x0000 1019 #define ICBZOPT_RSPSZ_12 0x0010 1020 #define ICBZOPT_RSPSZ_24A 0x0020 1021 #define ICBZOPT_RSPSZ_32 0x0030 1022 #define ICBZOPT_SOFTID 0x0002 1023 #define ICBZOPT_ENA_RDXFR_RDY 0x0001 1024 1025 /* 2400 F/W options */ 1026 #define ICB2400_OPT1_BOTH_WWNS 0x00004000 1027 #define ICB2400_OPT1_FULL_LOGIN 0x00002000 1028 #define ICB2400_OPT1_PREV_ADDRESS 0x00000800 1029 #define ICB2400_OPT1_SRCHDOWN 0x00000400 1030 #define ICB2400_OPT1_NOLIP 0x00000200 1031 #define ICB2400_OPT1_INI_DISABLE 0x00000020 1032 #define ICB2400_OPT1_TGT_ENABLE 0x00000010 1033 #define ICB2400_OPT1_FULL_DUPLEX 0x00000004 1034 #define ICB2400_OPT1_FAIRNESS 0x00000002 1035 #define ICB2400_OPT1_HARD_ADDRESS 0x00000001 1036 1037 #define ICB2400_OPT2_ENA_ATIOMQ 0x08000000 1038 #define ICB2400_OPT2_ENA_IHA 0x04000000 1039 #define ICB2400_OPT2_QOS 0x02000000 1040 #define ICB2400_OPT2_IOCBS 0x01000000 1041 #define ICB2400_OPT2_ENA_IHR 0x00400000 1042 #define ICB2400_OPT2_ENA_VMS 0x00200000 1043 #define ICB2400_OPT2_ENA_TA 0x00100000 1044 #define ICB2400_OPT2_TPRLIC 0x00004000 1045 #define ICB2400_OPT2_FCTAPE 0x00001000 1046 #define ICB2400_OPT2_FCSP 0x00000800 1047 #define ICB2400_OPT2_CLASS2_ACK0 0x00000200 1048 #define ICB2400_OPT2_CLASS2 0x00000100 1049 #define ICB2400_OPT2_NO_PLAY 0x00000080 1050 #define ICB2400_OPT2_TOPO_MASK 0x00000070 1051 #define ICB2400_OPT2_LOOP_ONLY 0x00000000 1052 #define ICB2400_OPT2_PTP_ONLY 0x00000010 1053 #define ICB2400_OPT2_LOOP_2_PTP 0x00000020 1054 #define ICB2400_OPT2_TIMER_MASK 0x0000000f 1055 #define ICB2400_OPT2_ZIO 0x00000005 1056 #define ICB2400_OPT2_ZIO1 0x00000006 1057 1058 #define ICB2400_OPT3_NO_CTXDIS 0x40000000 1059 #define ICB2400_OPT3_ENA_ETH_RESP 0x08000000 1060 #define ICB2400_OPT3_ENA_ETH_ATIO 0x04000000 1061 #define ICB2400_OPT3_ENA_MFCF 0x00020000 1062 #define ICB2400_OPT3_SKIP_4GB 0x00010000 1063 #define ICB2400_OPT3_RATE_MASK 0x0000E000 1064 #define ICB2400_OPT3_RATE_1GB 0x00000000 1065 #define ICB2400_OPT3_RATE_2GB 0x00002000 1066 #define ICB2400_OPT3_RATE_AUTO 0x00004000 1067 #define ICB2400_OPT3_RATE_4GB 0x00006000 1068 #define ICB2400_OPT3_RATE_8GB 0x00008000 1069 #define ICB2400_OPT3_RATE_16GB 0x0000A000 1070 #define ICB2400_OPT3_ENA_OOF_XFRDY 0x00000200 1071 #define ICB2400_OPT3_NO_N2N_LOGI 0x00000100 1072 #define ICB2400_OPT3_NO_LOCAL_PLOGI 0x00000080 1073 #define ICB2400_OPT3_ENA_OOF 0x00000040 1074 /* note that a response size flag of zero is reserved! */ 1075 #define ICB2400_OPT3_RSPSZ_MASK 0x00000030 1076 #define ICB2400_OPT3_RSPSZ_12 0x00000010 1077 #define ICB2400_OPT3_RSPSZ_24 0x00000020 1078 #define ICB2400_OPT3_RSPSZ_32 0x00000030 1079 #define ICB2400_OPT3_SOFTID 0x00000002 1080 1081 #define ICB_MIN_FRMLEN 256 1082 #define ICB_MAX_FRMLEN 2112 1083 #define ICB_DFLT_FRMLEN 1024 1084 #define ICB_DFLT_ALLOC 256 1085 #define ICB_DFLT_THROTTLE 16 1086 #define ICB_DFLT_RDELAY 5 1087 #define ICB_DFLT_RCOUNT 3 1088 1089 #define ICB_LOGIN_TOV 10 1090 #define ICB_LUN_ENABLE_TOV 15 1091 1092 1093 /* 1094 * And somebody at QLogic had a great idea that you could just change 1095 * the structure *and* keep the version number the same as the other cards. 1096 */ 1097 typedef struct { 1098 uint16_t icb_version; 1099 uint16_t icb_reserved0; 1100 uint16_t icb_maxfrmlen; 1101 uint16_t icb_execthrottle; 1102 uint16_t icb_xchgcnt; 1103 uint16_t icb_hardaddr; 1104 uint8_t icb_portname[8]; 1105 uint8_t icb_nodename[8]; 1106 uint16_t icb_rspnsin; 1107 uint16_t icb_rqstout; 1108 uint16_t icb_retry_count; 1109 uint16_t icb_priout; 1110 uint16_t icb_rsltqlen; 1111 uint16_t icb_rqstqlen; 1112 uint16_t icb_ldn_nols; 1113 uint16_t icb_prqstqlen; 1114 uint16_t icb_rqstaddr[4]; 1115 uint16_t icb_respaddr[4]; 1116 uint16_t icb_priaddr[4]; 1117 uint16_t icb_msixresp; 1118 uint16_t icb_msixatio; 1119 uint16_t icb_reserved1[2]; 1120 uint16_t icb_atio_in; 1121 uint16_t icb_atioqlen; 1122 uint16_t icb_atioqaddr[4]; 1123 uint16_t icb_idelaytimer; 1124 uint16_t icb_logintime; 1125 uint32_t icb_fwoptions1; 1126 uint32_t icb_fwoptions2; 1127 uint32_t icb_fwoptions3; 1128 uint16_t icb_qos; 1129 uint16_t icb_reserved2[3]; 1130 uint16_t icb_enodemac[3]; 1131 uint16_t icb_disctime; 1132 uint16_t icb_reserved3[4]; 1133 } isp_icb_2400_t; 1134 1135 #define RQRSP_ADDR0015 0 1136 #define RQRSP_ADDR1631 1 1137 #define RQRSP_ADDR3247 2 1138 #define RQRSP_ADDR4863 3 1139 1140 1141 #define ICB_NNM0 7 1142 #define ICB_NNM1 6 1143 #define ICB_NNM2 5 1144 #define ICB_NNM3 4 1145 #define ICB_NNM4 3 1146 #define ICB_NNM5 2 1147 #define ICB_NNM6 1 1148 #define ICB_NNM7 0 1149 1150 #define MAKE_NODE_NAME_FROM_WWN(array, wwn) \ 1151 array[ICB_NNM0] = (uint8_t) ((wwn >> 0) & 0xff), \ 1152 array[ICB_NNM1] = (uint8_t) ((wwn >> 8) & 0xff), \ 1153 array[ICB_NNM2] = (uint8_t) ((wwn >> 16) & 0xff), \ 1154 array[ICB_NNM3] = (uint8_t) ((wwn >> 24) & 0xff), \ 1155 array[ICB_NNM4] = (uint8_t) ((wwn >> 32) & 0xff), \ 1156 array[ICB_NNM5] = (uint8_t) ((wwn >> 40) & 0xff), \ 1157 array[ICB_NNM6] = (uint8_t) ((wwn >> 48) & 0xff), \ 1158 array[ICB_NNM7] = (uint8_t) ((wwn >> 56) & 0xff) 1159 1160 #define MAKE_WWN_FROM_NODE_NAME(wwn, array) \ 1161 wwn = ((uint64_t) array[ICB_NNM0]) | \ 1162 ((uint64_t) array[ICB_NNM1] << 8) | \ 1163 ((uint64_t) array[ICB_NNM2] << 16) | \ 1164 ((uint64_t) array[ICB_NNM3] << 24) | \ 1165 ((uint64_t) array[ICB_NNM4] << 32) | \ 1166 ((uint64_t) array[ICB_NNM5] << 40) | \ 1167 ((uint64_t) array[ICB_NNM6] << 48) | \ 1168 ((uint64_t) array[ICB_NNM7] << 56) 1169 1170 1171 /* 1172 * For MULTI_ID firmware, this describes a 1173 * virtual port entity for getting status. 1174 */ 1175 typedef struct { 1176 uint16_t vp_port_status; 1177 uint8_t vp_port_options; 1178 uint8_t vp_port_loopid; 1179 uint8_t vp_port_portname[8]; 1180 uint8_t vp_port_nodename[8]; 1181 uint16_t vp_port_portid_lo; /* not present when trailing icb */ 1182 uint16_t vp_port_portid_hi; /* not present when trailing icb */ 1183 } vp_port_info_t; 1184 1185 #define ICB2400_VPOPT_ENA_SNSLOGIN 0x00000040 /* Enable SNS Login and SCR for Virtual Ports */ 1186 #define ICB2400_VPOPT_TGT_DISABLE 0x00000020 /* Target Mode Disabled */ 1187 #define ICB2400_VPOPT_INI_ENABLE 0x00000010 /* Initiator Mode Enabled */ 1188 #define ICB2400_VPOPT_ENABLED 0x00000008 /* VP Enabled */ 1189 #define ICB2400_VPOPT_NOPLAY 0x00000004 /* ID Not Acquired */ 1190 #define ICB2400_VPOPT_PREV_ADDRESS 0x00000002 /* Previously Assigned ID */ 1191 #define ICB2400_VPOPT_HARD_ADDRESS 0x00000001 /* Hard Assigned ID */ 1192 1193 #define ICB2400_VPOPT_WRITE_SIZE 20 1194 1195 /* 1196 * For MULTI_ID firmware, we append this structure 1197 * to the isp_icb_2400_t above, followed by a list 1198 * structures that are *most* of the vp_port_info_t. 1199 */ 1200 typedef struct { 1201 uint16_t vp_count; 1202 uint16_t vp_global_options; 1203 } isp_icb_2400_vpinfo_t; 1204 1205 #define ICB2400_VPINFO_OFF 0x80 /* offset from start of ICB */ 1206 #define ICB2400_VPINFO_PORT_OFF(chan) \ 1207 (ICB2400_VPINFO_OFF + \ 1208 sizeof (isp_icb_2400_vpinfo_t) + (chan * ICB2400_VPOPT_WRITE_SIZE)) 1209 1210 #define ICB2400_VPGOPT_FCA 0x01 /* Assume Clean Address bit in FLOGI ACC set (works only in static configurations) */ 1211 #define ICB2400_VPGOPT_MID_DISABLE 0x02 /* when set, connection mode2 will work with NPIV-capable switched */ 1212 #define ICB2400_VPGOPT_VP0_DECOUPLE 0x04 /* Allow VP0 decoupling if firmware supports it */ 1213 #define ICB2400_VPGOPT_SUSP_FDISK 0x10 /* Suspend FDISC for Enabled VPs */ 1214 #define ICB2400_VPGOPT_GEN_RIDA 0x20 /* Generate RIDA if FLOGI Fails */ 1215 1216 typedef struct { 1217 isphdr_t vp_ctrl_hdr; 1218 uint32_t vp_ctrl_handle; 1219 uint16_t vp_ctrl_index_fail; 1220 uint16_t vp_ctrl_status; 1221 uint16_t vp_ctrl_command; 1222 uint16_t vp_ctrl_vp_count; 1223 uint16_t vp_ctrl_idmap[16]; 1224 uint16_t vp_ctrl_reserved[7]; 1225 uint16_t vp_ctrl_fcf_index; 1226 } vp_ctrl_info_t; 1227 1228 #define VP_CTRL_CMD_ENABLE_VP 0x00 1229 #define VP_CTRL_CMD_DISABLE_VP 0x08 1230 #define VP_CTRL_CMD_DISABLE_VP_REINIT_LINK 0x09 1231 #define VP_CTRL_CMD_DISABLE_VP_LOGO 0x0A 1232 #define VP_CTRL_CMD_DISABLE_VP_LOGO_ALL 0x0B 1233 1234 /* 1235 * We can use this structure for modifying either one or two VP ports after initialization 1236 */ 1237 typedef struct { 1238 isphdr_t vp_mod_hdr; 1239 uint32_t vp_mod_hdl; 1240 uint16_t vp_mod_reserved0; 1241 uint16_t vp_mod_status; 1242 uint8_t vp_mod_cmd; 1243 uint8_t vp_mod_cnt; 1244 uint8_t vp_mod_idx0; 1245 uint8_t vp_mod_idx1; 1246 struct { 1247 uint8_t options; 1248 uint8_t loopid; 1249 uint16_t reserved1; 1250 uint8_t wwpn[8]; 1251 uint8_t wwnn[8]; 1252 } vp_mod_ports[2]; 1253 uint8_t vp_mod_reserved2[8]; 1254 } vp_modify_t; 1255 1256 #define VP_STS_OK 0x00 1257 #define VP_STS_ERR 0x01 1258 #define VP_CNT_ERR 0x02 1259 #define VP_GEN_ERR 0x03 1260 #define VP_IDX_ERR 0x04 1261 #define VP_STS_BSY 0x05 1262 1263 #define VP_MODIFY 0x00 1264 #define VP_MODIFY_ENA 0x01 1265 #define VP_MODIFY_OPT 0x02 1266 #define VP_RESUME 0x03 1267 1268 /* 1269 * Port Data Base Element 1270 */ 1271 1272 typedef struct { 1273 uint16_t pdb_options; 1274 uint8_t pdb_mstate; 1275 uint8_t pdb_sstate; 1276 uint8_t pdb_hardaddr_bits[4]; 1277 uint8_t pdb_portid_bits[4]; 1278 uint8_t pdb_nodename[8]; 1279 uint8_t pdb_portname[8]; 1280 uint16_t pdb_execthrottle; 1281 uint16_t pdb_exec_count; 1282 uint8_t pdb_retry_count; 1283 uint8_t pdb_retry_delay; 1284 uint16_t pdb_resalloc; 1285 uint16_t pdb_curalloc; 1286 uint16_t pdb_qhead; 1287 uint16_t pdb_qtail; 1288 uint16_t pdb_tl_next; 1289 uint16_t pdb_tl_last; 1290 uint16_t pdb_features; /* PLOGI, Common Service */ 1291 uint16_t pdb_pconcurrnt; /* PLOGI, Common Service */ 1292 uint16_t pdb_roi; /* PLOGI, Common Service */ 1293 uint8_t pdb_target; 1294 uint8_t pdb_initiator; /* PLOGI, Class 3 Control Flags */ 1295 uint16_t pdb_rdsiz; /* PLOGI, Class 3 */ 1296 uint16_t pdb_ncseq; /* PLOGI, Class 3 */ 1297 uint16_t pdb_noseq; /* PLOGI, Class 3 */ 1298 uint16_t pdb_labrtflg; 1299 uint16_t pdb_lstopflg; 1300 uint16_t pdb_sqhead; 1301 uint16_t pdb_sqtail; 1302 uint16_t pdb_ptimer; 1303 uint16_t pdb_nxt_seqid; 1304 uint16_t pdb_fcount; 1305 uint16_t pdb_prli_len; 1306 uint16_t pdb_prli_svc0; 1307 uint16_t pdb_prli_svc3; 1308 uint16_t pdb_loopid; 1309 uint16_t pdb_il_ptr; 1310 uint16_t pdb_sl_ptr; 1311 } isp_pdb_21xx_t; 1312 1313 #define PDB_OPTIONS_XMITTING (1<<11) 1314 #define PDB_OPTIONS_LNKXMIT (1<<10) 1315 #define PDB_OPTIONS_ABORTED (1<<9) 1316 #define PDB_OPTIONS_ADISC (1<<1) 1317 1318 #define PDB_STATE_DISCOVERY 0 1319 #define PDB_STATE_WDISC_ACK 1 1320 #define PDB_STATE_PLOGI 2 1321 #define PDB_STATE_PLOGI_ACK 3 1322 #define PDB_STATE_PRLI 4 1323 #define PDB_STATE_PRLI_ACK 5 1324 #define PDB_STATE_LOGGED_IN 6 1325 #define PDB_STATE_PORT_UNAVAIL 7 1326 #define PDB_STATE_PRLO 8 1327 #define PDB_STATE_PRLO_ACK 9 1328 #define PDB_STATE_PLOGO 10 1329 #define PDB_STATE_PLOG_ACK 11 1330 1331 #define SVC3_ROLE_MASK 0x30 1332 #define SVC3_ROLE_SHIFT 4 1333 1334 #define BITS2WORD(x) ((x)[0] << 16 | (x)[3] << 8 | (x)[2]) 1335 #define BITS2WORD_24XX(x) ((x)[0] << 16 | (x)[1] << 8 | (x)[2]) 1336 1337 /* 1338 * Port Data Base Element- 24XX cards 1339 */ 1340 typedef struct { 1341 uint16_t pdb_flags; 1342 uint8_t pdb_curstate; 1343 uint8_t pdb_laststate; 1344 uint8_t pdb_hardaddr_bits[4]; 1345 uint8_t pdb_portid_bits[4]; 1346 #define pdb_nxt_seqid_2400 pdb_portid_bits[3] 1347 uint16_t pdb_retry_timer; 1348 uint16_t pdb_handle; 1349 uint16_t pdb_rcv_dsize; 1350 uint16_t pdb_reserved0; 1351 uint16_t pdb_prli_svc0; 1352 uint16_t pdb_prli_svc3; 1353 uint8_t pdb_portname[8]; 1354 uint8_t pdb_nodename[8]; 1355 uint8_t pdb_reserved1[24]; 1356 } isp_pdb_24xx_t; 1357 1358 #define PDB2400_TID_SUPPORTED 0x4000 1359 #define PDB2400_FC_TAPE 0x0080 1360 #define PDB2400_CLASS2_ACK0 0x0040 1361 #define PDB2400_FCP_CONF 0x0020 1362 #define PDB2400_CLASS2 0x0010 1363 #define PDB2400_ADDR_VALID 0x0002 1364 1365 #define PDB2400_STATE_PLOGI_PEND 0x03 1366 #define PDB2400_STATE_PLOGI_DONE 0x04 1367 #define PDB2400_STATE_PRLI_PEND 0x05 1368 #define PDB2400_STATE_LOGGED_IN 0x06 1369 #define PDB2400_STATE_PORT_UNAVAIL 0x07 1370 #define PDB2400_STATE_PRLO_PEND 0x09 1371 #define PDB2400_STATE_LOGO_PEND 0x0B 1372 1373 /* 1374 * Common elements from the above two structures that are actually useful to us. 1375 */ 1376 typedef struct { 1377 uint16_t handle; 1378 uint16_t prli_word3; 1379 uint32_t : 8, 1380 portid : 24; 1381 uint8_t portname[8]; 1382 uint8_t nodename[8]; 1383 } isp_pdb_t; 1384 1385 /* 1386 * Port/Node Name List Element 1387 */ 1388 typedef struct { 1389 uint8_t pnnle_name[8]; 1390 uint16_t pnnle_handle; 1391 uint16_t pnnle_reserved; 1392 } isp_pnnle_t; 1393 1394 #define PNNL_OPTIONS_NODE_NAMES (1<<0) 1395 #define PNNL_OPTIONS_PORT_DATA (1<<2) 1396 #define PNNL_OPTIONS_INITIATORS (1<<3) 1397 1398 /* 1399 * Port and N-Port Handle List Element 1400 */ 1401 typedef struct { 1402 uint16_t pnhle_port_id_lo; 1403 uint16_t pnhle_port_id_hi_handle; 1404 } isp_pnhle_21xx_t; 1405 1406 typedef struct { 1407 uint16_t pnhle_port_id_lo; 1408 uint16_t pnhle_port_id_hi; 1409 uint16_t pnhle_handle; 1410 } isp_pnhle_23xx_t; 1411 1412 typedef struct { 1413 uint16_t pnhle_port_id_lo; 1414 uint16_t pnhle_port_id_hi; 1415 uint16_t pnhle_handle; 1416 uint16_t pnhle_reserved; 1417 } isp_pnhle_24xx_t; 1418 1419 /* 1420 * Port Database Changed Async Event information for 24XX cards 1421 */ 1422 #define PDB24XX_AE_OK 0x00 1423 #define PDB24XX_AE_IMPL_LOGO_1 0x01 1424 #define PDB24XX_AE_IMPL_LOGO_2 0x02 1425 #define PDB24XX_AE_IMPL_LOGO_3 0x03 1426 #define PDB24XX_AE_PLOGI_RCVD 0x04 1427 #define PDB24XX_AE_PLOGI_RJT 0x05 1428 #define PDB24XX_AE_PRLI_RCVD 0x06 1429 #define PDB24XX_AE_PRLI_RJT 0x07 1430 #define PDB24XX_AE_TPRLO 0x08 1431 #define PDB24XX_AE_TPRLO_RJT 0x09 1432 #define PDB24XX_AE_PRLO_RCVD 0x0a 1433 #define PDB24XX_AE_LOGO_RCVD 0x0b 1434 #define PDB24XX_AE_TOPO_CHG 0x0c 1435 #define PDB24XX_AE_NPORT_CHG 0x0d 1436 #define PDB24XX_AE_FLOGI_RJT 0x0e 1437 #define PDB24XX_AE_BAD_FANN 0x0f 1438 #define PDB24XX_AE_FLOGI_TIMO 0x10 1439 #define PDB24XX_AE_ABX_LOGO 0x11 1440 #define PDB24XX_AE_PLOGI_DONE 0x12 1441 #define PDB24XX_AE_PRLI_DONJE 0x13 1442 #define PDB24XX_AE_OPN_1 0x14 1443 #define PDB24XX_AE_OPN_2 0x15 1444 #define PDB24XX_AE_TXERR 0x16 1445 #define PDB24XX_AE_FORCED_LOGO 0x17 1446 #define PDB24XX_AE_DISC_TIMO 0x18 1447 1448 /* 1449 * Genericized Port Login/Logout software structure 1450 */ 1451 typedef struct { 1452 uint16_t handle; 1453 uint16_t channel; 1454 uint32_t 1455 flags : 8, 1456 portid : 24; 1457 } isp_plcmd_t; 1458 /* the flags to use are those for PLOGX_FLG_* below */ 1459 1460 /* 1461 * ISP24XX- Login/Logout Port IOCB 1462 */ 1463 typedef struct { 1464 isphdr_t plogx_header; 1465 uint32_t plogx_handle; 1466 uint16_t plogx_status; 1467 uint16_t plogx_nphdl; 1468 uint16_t plogx_flags; 1469 uint16_t plogx_vphdl; /* low 8 bits */ 1470 uint16_t plogx_portlo; /* low 16 bits */ 1471 uint16_t plogx_rspsz_porthi; 1472 struct { 1473 uint16_t lo16; 1474 uint16_t hi16; 1475 } plogx_ioparm[11]; 1476 } isp_plogx_t; 1477 1478 #define PLOGX_STATUS_OK 0x00 1479 #define PLOGX_STATUS_UNAVAIL 0x28 1480 #define PLOGX_STATUS_LOGOUT 0x29 1481 #define PLOGX_STATUS_IOCBERR 0x31 1482 1483 #define PLOGX_IOCBERR_NOLINK 0x01 1484 #define PLOGX_IOCBERR_NOIOCB 0x02 1485 #define PLOGX_IOCBERR_NOXGHG 0x03 1486 #define PLOGX_IOCBERR_FAILED 0x04 /* further info in IOPARM 1 */ 1487 #define PLOGX_IOCBERR_NOFABRIC 0x05 1488 #define PLOGX_IOCBERR_NOTREADY 0x07 1489 #define PLOGX_IOCBERR_NOLOGIN 0x09 /* further info in IOPARM 1 */ 1490 #define PLOGX_IOCBERR_NOPCB 0x0a 1491 #define PLOGX_IOCBERR_REJECT 0x18 /* further info in IOPARM 1 */ 1492 #define PLOGX_IOCBERR_EINVAL 0x19 /* further info in IOPARM 1 */ 1493 #define PLOGX_IOCBERR_PORTUSED 0x1a /* further info in IOPARM 1 */ 1494 #define PLOGX_IOCBERR_HNDLUSED 0x1b /* further info in IOPARM 1 */ 1495 #define PLOGX_IOCBERR_NOHANDLE 0x1c 1496 #define PLOGX_IOCBERR_NOFLOGI 0x1f /* further info in IOPARM 1 */ 1497 1498 #define PLOGX_FLG_CMD_MASK 0xf 1499 #define PLOGX_FLG_CMD_PLOGI 0 1500 #define PLOGX_FLG_CMD_PRLI 1 1501 #define PLOGX_FLG_CMD_PDISC 2 1502 #define PLOGX_FLG_CMD_LOGO 8 1503 #define PLOGX_FLG_CMD_PRLO 9 1504 #define PLOGX_FLG_CMD_TPRLO 10 1505 1506 #define PLOGX_FLG_COND_PLOGI 0x10 /* if with PLOGI */ 1507 #define PLOGX_FLG_IMPLICIT 0x10 /* if with LOGO, PRLO, TPRLO */ 1508 #define PLOGX_FLG_SKIP_PRLI 0x20 /* if with PLOGI */ 1509 #define PLOGX_FLG_IMPLICIT_LOGO_ALL 0x20 /* if with LOGO */ 1510 #define PLOGX_FLG_EXPLICIT_LOGO 0x40 /* if with LOGO */ 1511 #define PLOGX_FLG_COMMON_FEATURES 0x80 /* if with PLOGI */ 1512 #define PLOGX_FLG_FREE_NPHDL 0x80 /* if with with LOGO */ 1513 1514 #define PLOGX_FLG_CLASS2 0x100 /* if with PLOGI */ 1515 #define PLOGX_FLG_FCP2_OVERRIDE 0x200 /* if with PRLOG, PRLI */ 1516 1517 /* 1518 * Report ID Acquisistion (24XX multi-id firmware) 1519 */ 1520 typedef struct { 1521 isphdr_t ridacq_hdr; 1522 uint32_t ridacq_handle; 1523 uint8_t ridacq_vp_acquired; 1524 uint8_t ridacq_vp_setup; 1525 uint8_t ridacq_vp_index; 1526 uint8_t ridacq_vp_status; 1527 uint16_t ridacq_vp_port_lo; 1528 uint8_t ridacq_vp_port_hi; 1529 uint8_t ridacq_format; /* 0 or 1 */ 1530 uint16_t ridacq_map[8]; 1531 uint8_t ridacq_reserved1[32]; 1532 } isp_ridacq_t; 1533 1534 #define RIDACQ_STS_COMPLETE 0 1535 #define RIDACQ_STS_UNACQUIRED 1 1536 #define RIDACQ_STS_CHANGED 2 1537 #define RIDACQ_STS_SNS_TIMEOUT 3 1538 #define RIDACQ_STS_SNS_REJECTED 4 1539 #define RIDACQ_STS_SCR_TIMEOUT 5 1540 #define RIDACQ_STS_SCR_REJECTED 6 1541 1542 /* 1543 * Simple Name Server Data Structures 1544 */ 1545 #define SNS_GA_NXT 0x100 1546 #define SNS_GPN_ID 0x112 1547 #define SNS_GNN_ID 0x113 1548 #define SNS_GFF_ID 0x11F 1549 #define SNS_GID_FT 0x171 1550 #define SNS_RFT_ID 0x217 1551 #define SNS_RFF_ID 0x21F 1552 typedef struct { 1553 uint16_t snscb_rblen; /* response buffer length (words) */ 1554 uint16_t snscb_reserved0; 1555 uint16_t snscb_addr[4]; /* response buffer address */ 1556 uint16_t snscb_sblen; /* subcommand buffer length (words) */ 1557 uint16_t snscb_reserved1; 1558 uint16_t snscb_data[]; /* variable data */ 1559 } sns_screq_t; /* Subcommand Request Structure */ 1560 1561 typedef struct { 1562 uint16_t snscb_rblen; /* response buffer length (words) */ 1563 uint16_t snscb_reserved0; 1564 uint16_t snscb_addr[4]; /* response buffer address */ 1565 uint16_t snscb_sblen; /* subcommand buffer length (words) */ 1566 uint16_t snscb_reserved1; 1567 uint16_t snscb_cmd; 1568 uint16_t snscb_reserved2; 1569 uint32_t snscb_reserved3; 1570 uint32_t snscb_port; 1571 } sns_ga_nxt_req_t; 1572 #define SNS_GA_NXT_REQ_SIZE (sizeof (sns_ga_nxt_req_t)) 1573 1574 typedef struct { 1575 uint16_t snscb_rblen; /* response buffer length (words) */ 1576 uint16_t snscb_reserved0; 1577 uint16_t snscb_addr[4]; /* response buffer address */ 1578 uint16_t snscb_sblen; /* subcommand buffer length (words) */ 1579 uint16_t snscb_reserved1; 1580 uint16_t snscb_cmd; 1581 uint16_t snscb_reserved2; 1582 uint32_t snscb_reserved3; 1583 uint32_t snscb_portid; 1584 } sns_gxn_id_req_t; 1585 #define SNS_GXN_ID_REQ_SIZE (sizeof (sns_gxn_id_req_t)) 1586 1587 typedef struct { 1588 uint16_t snscb_rblen; /* response buffer length (words) */ 1589 uint16_t snscb_reserved0; 1590 uint16_t snscb_addr[4]; /* response buffer address */ 1591 uint16_t snscb_sblen; /* subcommand buffer length (words) */ 1592 uint16_t snscb_reserved1; 1593 uint16_t snscb_cmd; 1594 uint16_t snscb_mword_div_2; 1595 uint32_t snscb_reserved3; 1596 uint32_t snscb_fc4_type; 1597 } sns_gid_ft_req_t; 1598 #define SNS_GID_FT_REQ_SIZE (sizeof (sns_gid_ft_req_t)) 1599 1600 typedef struct { 1601 uint16_t snscb_rblen; /* response buffer length (words) */ 1602 uint16_t snscb_reserved0; 1603 uint16_t snscb_addr[4]; /* response buffer address */ 1604 uint16_t snscb_sblen; /* subcommand buffer length (words) */ 1605 uint16_t snscb_reserved1; 1606 uint16_t snscb_cmd; 1607 uint16_t snscb_reserved2; 1608 uint32_t snscb_reserved3; 1609 uint32_t snscb_port; 1610 uint32_t snscb_fc4_types[8]; 1611 } sns_rft_id_req_t; 1612 #define SNS_RFT_ID_REQ_SIZE (sizeof (sns_rft_id_req_t)) 1613 1614 typedef struct { 1615 ct_hdr_t snscb_cthdr; 1616 uint8_t snscb_port_type; 1617 uint8_t snscb_port_id[3]; 1618 uint8_t snscb_portname[8]; 1619 uint16_t snscb_data[]; /* variable data */ 1620 } sns_scrsp_t; /* Subcommand Response Structure */ 1621 1622 typedef struct { 1623 ct_hdr_t snscb_cthdr; 1624 uint8_t snscb_port_type; 1625 uint8_t snscb_port_id[3]; 1626 uint8_t snscb_portname[8]; 1627 uint8_t snscb_pnlen; /* symbolic port name length */ 1628 uint8_t snscb_pname[255]; /* symbolic port name */ 1629 uint8_t snscb_nodename[8]; 1630 uint8_t snscb_nnlen; /* symbolic node name length */ 1631 uint8_t snscb_nname[255]; /* symbolic node name */ 1632 uint8_t snscb_ipassoc[8]; 1633 uint8_t snscb_ipaddr[16]; 1634 uint8_t snscb_svc_class[4]; 1635 uint8_t snscb_fc4_types[32]; 1636 uint8_t snscb_fpname[8]; 1637 uint8_t snscb_reserved; 1638 uint8_t snscb_hardaddr[3]; 1639 } sns_ga_nxt_rsp_t; /* Subcommand Response Structure */ 1640 #define SNS_GA_NXT_RESP_SIZE (sizeof (sns_ga_nxt_rsp_t)) 1641 1642 typedef struct { 1643 ct_hdr_t snscb_cthdr; 1644 uint8_t snscb_wwn[8]; 1645 } sns_gxn_id_rsp_t; 1646 #define SNS_GXN_ID_RESP_SIZE (sizeof (sns_gxn_id_rsp_t)) 1647 1648 typedef struct { 1649 ct_hdr_t snscb_cthdr; 1650 uint32_t snscb_fc4_features[32]; 1651 } sns_gff_id_rsp_t; 1652 #define SNS_GFF_ID_RESP_SIZE (sizeof (sns_gff_id_rsp_t)) 1653 1654 typedef struct { 1655 ct_hdr_t snscb_cthdr; 1656 struct { 1657 uint8_t control; 1658 uint8_t portid[3]; 1659 } snscb_ports[1]; 1660 } sns_gid_ft_rsp_t; 1661 #define SNS_GID_FT_RESP_SIZE(x) ((sizeof (sns_gid_ft_rsp_t)) + ((x - 1) << 2)) 1662 #define SNS_RFT_ID_RESP_SIZE (sizeof (ct_hdr_t)) 1663 1664 /* 1665 * Other Misc Structures 1666 */ 1667 1668 /* ELS Pass Through */ 1669 typedef struct { 1670 isphdr_t els_hdr; 1671 uint32_t els_handle; 1672 uint16_t els_status; 1673 uint16_t els_nphdl; 1674 uint16_t els_xmit_dsd_count; /* outgoing only */ 1675 uint8_t els_vphdl; 1676 uint8_t els_sof; 1677 uint32_t els_rxid; 1678 uint16_t els_recv_dsd_count; /* outgoing only */ 1679 uint8_t els_opcode; 1680 uint8_t els_reserved1; 1681 uint8_t els_did_lo; 1682 uint8_t els_did_mid; 1683 uint8_t els_did_hi; 1684 uint8_t els_reserved2; 1685 uint16_t els_reserved3; 1686 uint16_t els_ctl_flags; 1687 union { 1688 struct { 1689 uint32_t _els_bytecnt; 1690 uint32_t _els_subcode1; 1691 uint32_t _els_subcode2; 1692 uint8_t _els_reserved4[20]; 1693 } in; 1694 struct { 1695 uint32_t _els_recv_bytecnt; 1696 uint32_t _els_xmit_bytecnt; 1697 uint32_t _els_xmit_dsd_length; 1698 uint16_t _els_xmit_dsd_a1500; 1699 uint16_t _els_xmit_dsd_a3116; 1700 uint16_t _els_xmit_dsd_a4732; 1701 uint16_t _els_xmit_dsd_a6348; 1702 uint32_t _els_recv_dsd_length; 1703 uint16_t _els_recv_dsd_a1500; 1704 uint16_t _els_recv_dsd_a3116; 1705 uint16_t _els_recv_dsd_a4732; 1706 uint16_t _els_recv_dsd_a6348; 1707 } out; 1708 } inout; 1709 #define els_bytecnt inout.in._els_bytecnt 1710 #define els_subcode1 inout.in._els_subcode1 1711 #define els_subcode2 inout.in._els_subcode2 1712 #define els_reserved4 inout.in._els_reserved4 1713 #define els_recv_bytecnt inout.out._els_recv_bytecnt 1714 #define els_xmit_bytecnt inout.out._els_xmit_bytecnt 1715 #define els_xmit_dsd_length inout.out._els_xmit_dsd_length 1716 #define els_xmit_dsd_a1500 inout.out._els_xmit_dsd_a1500 1717 #define els_xmit_dsd_a3116 inout.out._els_xmit_dsd_a3116 1718 #define els_xmit_dsd_a4732 inout.out._els_xmit_dsd_a4732 1719 #define els_xmit_dsd_a6348 inout.out._els_xmit_dsd_a6348 1720 #define els_recv_dsd_length inout.out._els_recv_dsd_length 1721 #define els_recv_dsd_a1500 inout.out._els_recv_dsd_a1500 1722 #define els_recv_dsd_a3116 inout.out._els_recv_dsd_a3116 1723 #define els_recv_dsd_a4732 inout.out._els_recv_dsd_a4732 1724 #define els_recv_dsd_a6348 inout.out._els_recv_dsd_a6348 1725 } els_t; 1726 1727 /* 1728 * A handy package structure for running FC-SCSI commands internally 1729 */ 1730 typedef struct { 1731 uint16_t handle; 1732 uint16_t lun; 1733 uint32_t 1734 channel : 8, 1735 portid : 24; 1736 uint32_t timeout; 1737 union { 1738 struct { 1739 uint32_t data_length; 1740 uint32_t 1741 no_wait : 1, 1742 do_read : 1; 1743 uint8_t cdb[16]; 1744 void *data_ptr; 1745 } beg; 1746 struct { 1747 uint32_t data_residual; 1748 uint8_t status; 1749 uint8_t pad; 1750 uint16_t sense_length; 1751 uint8_t sense_data[32]; 1752 } end; 1753 } fcd; 1754 } isp_xcmd_t; 1755 1756 /* 1757 * Target Mode related definitions 1758 */ 1759 #define QLTM_SENSELEN 18 /* non-FC cards only */ 1760 #define QLTM_SVALID 0x80 1761 1762 /* 1763 * Structure for Enable Lun and Modify Lun queue entries 1764 */ 1765 typedef struct { 1766 isphdr_t le_header; 1767 uint32_t le_reserved; 1768 uint8_t le_lun; 1769 uint8_t le_rsvd; 1770 uint8_t le_ops; /* Modify LUN only */ 1771 uint8_t le_tgt; /* Not for FC */ 1772 uint32_t le_flags; /* Not for FC */ 1773 uint8_t le_status; 1774 uint8_t le_reserved2; 1775 uint8_t le_cmd_count; 1776 uint8_t le_in_count; 1777 uint8_t le_cdb6len; /* Not for FC */ 1778 uint8_t le_cdb7len; /* Not for FC */ 1779 uint16_t le_timeout; 1780 uint16_t le_reserved3[20]; 1781 } lun_entry_t; 1782 1783 /* 1784 * le_flags values 1785 */ 1786 #define LUN_TQAE 0x00000002 /* bit1 Tagged Queue Action Enable */ 1787 #define LUN_DSSM 0x01000000 /* bit24 Disable Sending SDP Message */ 1788 #define LUN_DISAD 0x02000000 /* bit25 Disable autodisconnect */ 1789 #define LUN_DM 0x40000000 /* bit30 Disconnects Mandatory */ 1790 1791 /* 1792 * le_ops values 1793 */ 1794 #define LUN_CCINCR 0x01 /* increment command count */ 1795 #define LUN_CCDECR 0x02 /* decrement command count */ 1796 #define LUN_ININCR 0x40 /* increment immed. notify count */ 1797 #define LUN_INDECR 0x80 /* decrement immed. notify count */ 1798 1799 /* 1800 * le_status values 1801 */ 1802 #define LUN_OK 0x01 /* we be rockin' */ 1803 #define LUN_ERR 0x04 /* request completed with error */ 1804 #define LUN_INVAL 0x06 /* invalid request */ 1805 #define LUN_NOCAP 0x16 /* can't provide requested capability */ 1806 #define LUN_ENABLED 0x3E /* LUN already enabled */ 1807 1808 /* 1809 * Immediate Notify Entry structure 1810 */ 1811 #define IN_MSGLEN 8 /* 8 bytes */ 1812 #define IN_RSVDLEN 8 /* 8 words */ 1813 typedef struct { 1814 isphdr_t in_header; 1815 uint32_t in_reserved; 1816 uint8_t in_lun; /* lun */ 1817 uint8_t in_iid; /* initiator */ 1818 uint8_t in_reserved2; 1819 uint8_t in_tgt; /* target */ 1820 uint32_t in_flags; 1821 uint8_t in_status; 1822 uint8_t in_rsvd2; 1823 uint8_t in_tag_val; /* tag value */ 1824 uint8_t in_tag_type; /* tag type */ 1825 uint16_t in_seqid; /* sequence id */ 1826 uint8_t in_msg[IN_MSGLEN]; /* SCSI message bytes */ 1827 uint16_t in_reserved3[IN_RSVDLEN]; 1828 uint8_t in_sense[QLTM_SENSELEN];/* suggested sense data */ 1829 } in_entry_t; 1830 1831 typedef struct { 1832 isphdr_t in_header; 1833 uint32_t in_reserved; 1834 uint8_t in_lun; /* lun */ 1835 uint8_t in_iid; /* initiator */ 1836 uint16_t in_scclun; 1837 uint32_t in_reserved2; 1838 uint16_t in_status; 1839 uint16_t in_task_flags; 1840 uint16_t in_seqid; /* sequence id */ 1841 } in_fcentry_t; 1842 1843 typedef struct { 1844 isphdr_t in_header; 1845 uint32_t in_reserved; 1846 uint16_t in_iid; /* initiator */ 1847 uint16_t in_scclun; 1848 uint32_t in_reserved2; 1849 uint16_t in_status; 1850 uint16_t in_task_flags; 1851 uint16_t in_seqid; /* sequence id */ 1852 } in_fcentry_e_t; 1853 1854 /* 1855 * Values for the in_status field 1856 */ 1857 #define IN_REJECT 0x0D /* Message Reject message received */ 1858 #define IN_RESET 0x0E /* Bus Reset occurred */ 1859 #define IN_NO_RCAP 0x16 /* requested capability not available */ 1860 #define IN_IDE_RECEIVED 0x33 /* Initiator Detected Error msg received */ 1861 #define IN_RSRC_UNAVAIL 0x34 /* resource unavailable */ 1862 #define IN_MSG_RECEIVED 0x36 /* SCSI message received */ 1863 #define IN_ABORT_TASK 0x20 /* task named in RX_ID is being aborted (FC) */ 1864 #define IN_PORT_LOGOUT 0x29 /* port has logged out (FC) */ 1865 #define IN_PORT_CHANGED 0x2A /* port changed */ 1866 #define IN_GLOBAL_LOGO 0x2E /* all ports logged out */ 1867 #define IN_NO_NEXUS 0x3B /* Nexus not established */ 1868 #define IN_SRR_RCVD 0x45 /* SRR received */ 1869 1870 /* 1871 * Values for the in_task_flags field- should only get one at a time! 1872 */ 1873 #define TASK_FLAGS_RESERVED_MASK (0xe700) 1874 #define TASK_FLAGS_CLEAR_ACA (1<<14) 1875 #define TASK_FLAGS_TARGET_RESET (1<<13) 1876 #define TASK_FLAGS_LUN_RESET (1<<12) 1877 #define TASK_FLAGS_CLEAR_TASK_SET (1<<10) 1878 #define TASK_FLAGS_ABORT_TASK_SET (1<<9) 1879 1880 /* 1881 * ISP24XX Immediate Notify 1882 */ 1883 typedef struct { 1884 isphdr_t in_header; 1885 uint32_t in_reserved; 1886 uint16_t in_nphdl; 1887 uint16_t in_reserved1; 1888 uint16_t in_flags; 1889 uint16_t in_srr_rxid; 1890 uint16_t in_status; 1891 uint8_t in_status_subcode; 1892 uint8_t in_fwhandle; 1893 uint32_t in_rxid; 1894 uint16_t in_srr_reloff_lo; 1895 uint16_t in_srr_reloff_hi; 1896 uint16_t in_srr_iu; 1897 uint16_t in_srr_oxid; 1898 /* 1899 * If bit 2 is set in in_flags, the N-Port and 1900 * handle tags are valid. If the received ELS is 1901 * a LOGO, then these tags contain the N Port ID 1902 * from the LOGO payload. If the received ELS 1903 * request is TPRLO, these tags contain the 1904 * Third Party Originator N Port ID. 1905 */ 1906 uint16_t in_nport_id_hi; 1907 #define in_prli_options in_nport_id_hi 1908 uint8_t in_nport_id_lo; 1909 uint8_t in_reserved3; 1910 uint16_t in_np_handle; 1911 uint8_t in_reserved4[12]; 1912 uint8_t in_reserved5; 1913 uint8_t in_vpidx; 1914 uint32_t in_reserved6; 1915 uint16_t in_portid_lo; 1916 uint8_t in_portid_hi; 1917 uint8_t in_reserved7; 1918 uint16_t in_reserved8; 1919 uint16_t in_oxid; 1920 } in_fcentry_24xx_t; 1921 1922 #define IN24XX_FLAG_PUREX_IOCB 0x1 1923 #define IN24XX_FLAG_GLOBAL_LOGOUT 0x2 1924 #define IN24XX_FLAG_NPHDL_VALID 0x4 1925 #define IN24XX_FLAG_N2N_PRLI 0x8 1926 #define IN24XX_FLAG_PN_NN_VALID 0x10 1927 1928 #define IN24XX_LIP_RESET 0x0E 1929 #define IN24XX_LINK_RESET 0x0F 1930 #define IN24XX_PORT_LOGOUT 0x29 1931 #define IN24XX_PORT_CHANGED 0x2A 1932 #define IN24XX_LINK_FAILED 0x2E 1933 #define IN24XX_SRR_RCVD 0x45 1934 #define IN24XX_ELS_RCVD 0x46 /* 1935 * login-affectin ELS received- check 1936 * subcode for specific opcode 1937 */ 1938 1939 /* 1940 * For f/w > 4.0.25, these offsets in the Immediate Notify contain 1941 * the WWNN/WWPN if the ELS is PLOGI, PDISC or ADISC. The WWN is in 1942 * Big Endian format. 1943 */ 1944 #define IN24XX_PRLI_WWNN_OFF 0x18 1945 #define IN24XX_PRLI_WWPN_OFF 0x28 1946 #define IN24XX_PLOGI_WWNN_OFF 0x20 1947 #define IN24XX_PLOGI_WWPN_OFF 0x28 1948 1949 /* 1950 * For f/w > 4.0.25, this offset in the Immediate Notify contain 1951 * the WWPN if the ELS is LOGO. The WWN is in Big Endian format. 1952 */ 1953 #define IN24XX_LOGO_WWPN_OFF 0x28 1954 1955 /* 1956 * Immediate Notify Status Subcodes for IN24XX_PORT_LOGOUT 1957 */ 1958 #define IN24XX_PORT_LOGOUT_PDISC_TMO 0x00 1959 #define IN24XX_PORT_LOGOUT_UXPR_DISC 0x01 1960 #define IN24XX_PORT_LOGOUT_OWN_OPN 0x02 1961 #define IN24XX_PORT_LOGOUT_OWN_OPN_SFT 0x03 1962 #define IN24XX_PORT_LOGOUT_ABTS_TMO 0x04 1963 #define IN24XX_PORT_LOGOUT_DISC_RJT 0x05 1964 #define IN24XX_PORT_LOGOUT_LOGIN_NEEDED 0x06 1965 #define IN24XX_PORT_LOGOUT_BAD_DISC 0x07 1966 #define IN24XX_PORT_LOGOUT_LOST_ALPA 0x08 1967 #define IN24XX_PORT_LOGOUT_XMIT_FAILURE 0x09 1968 1969 /* 1970 * Immediate Notify Status Subcodes for IN24XX_PORT_CHANGED 1971 */ 1972 #define IN24XX_PORT_CHANGED_BADFAN 0x00 1973 #define IN24XX_PORT_CHANGED_TOPO_CHANGE 0x01 1974 #define IN24XX_PORT_CHANGED_FLOGI_ACC 0x02 1975 #define IN24XX_PORT_CHANGED_FLOGI_RJT 0x03 1976 #define IN24XX_PORT_CHANGED_TIMEOUT 0x04 1977 #define IN24XX_PORT_CHANGED_PORT_CHANGE 0x05 1978 1979 /* 1980 * Notify Acknowledge Entry structure 1981 */ 1982 #define NA_RSVDLEN 22 1983 typedef struct { 1984 isphdr_t na_header; 1985 uint32_t na_reserved; 1986 uint8_t na_lun; /* lun */ 1987 uint8_t na_iid; /* initiator */ 1988 uint8_t na_reserved2; 1989 uint8_t na_tgt; /* target */ 1990 uint32_t na_flags; 1991 uint8_t na_status; 1992 uint8_t na_event; 1993 uint16_t na_seqid; /* sequence id */ 1994 uint16_t na_reserved3[NA_RSVDLEN]; 1995 } na_entry_t; 1996 1997 /* 1998 * Value for the na_event field 1999 */ 2000 #define NA_RST_CLRD 0x80 /* Clear an async event notification */ 2001 #define NA_OK 0x01 /* Notify Acknowledge Succeeded */ 2002 #define NA_INVALID 0x06 /* Invalid Notify Acknowledge */ 2003 2004 #define NA2_RSVDLEN 21 2005 typedef struct { 2006 isphdr_t na_header; 2007 uint32_t na_reserved; 2008 uint8_t na_reserved1; 2009 uint8_t na_iid; /* initiator loop id */ 2010 uint16_t na_response; 2011 uint16_t na_flags; 2012 uint16_t na_reserved2; 2013 uint16_t na_status; 2014 uint16_t na_task_flags; 2015 uint16_t na_seqid; /* sequence id */ 2016 uint16_t na_reserved3[NA2_RSVDLEN]; 2017 } na_fcentry_t; 2018 2019 typedef struct { 2020 isphdr_t na_header; 2021 uint32_t na_reserved; 2022 uint16_t na_iid; /* initiator loop id */ 2023 uint16_t na_response; /* response code */ 2024 uint16_t na_flags; 2025 uint16_t na_reserved2; 2026 uint16_t na_status; 2027 uint16_t na_task_flags; 2028 uint16_t na_seqid; /* sequence id */ 2029 uint16_t na_reserved3[NA2_RSVDLEN]; 2030 } na_fcentry_e_t; 2031 2032 #define NAFC_RCOUNT 0x80 /* increment resource count */ 2033 #define NAFC_RST_CLRD 0x20 /* Clear LIP Reset */ 2034 #define NAFC_TVALID 0x10 /* task mangement response code is valid */ 2035 2036 /* 2037 * ISP24XX Notify Acknowledge 2038 */ 2039 2040 typedef struct { 2041 isphdr_t na_header; 2042 uint32_t na_handle; 2043 uint16_t na_nphdl; 2044 uint16_t na_reserved1; 2045 uint16_t na_flags; 2046 uint16_t na_srr_rxid; 2047 uint16_t na_status; 2048 uint8_t na_status_subcode; 2049 uint8_t na_fwhandle; 2050 uint32_t na_rxid; 2051 uint16_t na_srr_reloff_lo; 2052 uint16_t na_srr_reloff_hi; 2053 uint16_t na_srr_iu; 2054 uint16_t na_srr_flags; 2055 uint8_t na_reserved3[18]; 2056 uint8_t na_reserved4; 2057 uint8_t na_vpidx; 2058 uint8_t na_srr_reject_vunique; 2059 uint8_t na_srr_reject_explanation; 2060 uint8_t na_srr_reject_code; 2061 uint8_t na_reserved5; 2062 uint8_t na_reserved6[6]; 2063 uint16_t na_oxid; 2064 } na_fcentry_24xx_t; 2065 2066 /* 2067 * Accept Target I/O Entry structure 2068 */ 2069 #define ATIO_CDBLEN 26 2070 2071 typedef struct { 2072 isphdr_t at_header; 2073 uint16_t at_reserved; 2074 uint16_t at_handle; 2075 uint8_t at_lun; /* lun */ 2076 uint8_t at_iid; /* initiator */ 2077 uint8_t at_cdblen; /* cdb length */ 2078 uint8_t at_tgt; /* target */ 2079 uint32_t at_flags; 2080 uint8_t at_status; /* firmware status */ 2081 uint8_t at_scsi_status; /* scsi status */ 2082 uint8_t at_tag_val; /* tag value */ 2083 uint8_t at_tag_type; /* tag type */ 2084 uint8_t at_cdb[ATIO_CDBLEN]; /* received CDB */ 2085 uint8_t at_sense[QLTM_SENSELEN];/* suggested sense data */ 2086 } at_entry_t; 2087 2088 /* 2089 * at_flags values 2090 */ 2091 #define AT_NODISC 0x00008000 /* disconnect disabled */ 2092 #define AT_TQAE 0x00000002 /* Tagged Queue Action enabled */ 2093 2094 /* 2095 * at_status values 2096 */ 2097 #define AT_PATH_INVALID 0x07 /* ATIO sent to firmware for disabled lun */ 2098 #define AT_RESET 0x0E /* SCSI Bus Reset Occurred */ 2099 #define AT_PHASE_ERROR 0x14 /* Bus phase sequence error */ 2100 #define AT_NOCAP 0x16 /* Requested capability not available */ 2101 #define AT_BDR_MSG 0x17 /* Bus Device Reset msg received */ 2102 #define AT_CDB 0x3D /* CDB received */ 2103 /* 2104 * Macros to create and fetch and test concatenated handle and tag value macros 2105 * (SPI only) 2106 */ 2107 #define AT_MAKE_TAGID(tid, aep) \ 2108 tid = aep->at_handle; \ 2109 if (aep->at_flags & AT_TQAE) { \ 2110 tid |= (aep->at_tag_val << 16); \ 2111 tid |= (1 << 24); \ 2112 } 2113 2114 #define CT_MAKE_TAGID(tid, ct) \ 2115 tid = ct->ct_fwhandle; \ 2116 if (ct->ct_flags & CT_TQAE) { \ 2117 tid |= (ct->ct_tag_val << 16); \ 2118 tid |= (1 << 24); \ 2119 } 2120 2121 #define AT_HAS_TAG(val) ((val) & (1 << 24)) 2122 #define AT_GET_TAG(val) (((val) >> 16) & 0xff) 2123 #define AT_GET_HANDLE(val) ((val) & 0xffff) 2124 2125 #define IN_MAKE_TAGID(tid, inp) \ 2126 tid = inp->in_seqid; \ 2127 tid |= (inp->in_tag_val << 16); \ 2128 tid |= (1 << 24) 2129 2130 /* 2131 * Accept Target I/O Entry structure, Type 2 2132 */ 2133 #define ATIO2_CDBLEN 16 2134 2135 typedef struct { 2136 isphdr_t at_header; 2137 uint32_t at_reserved; 2138 uint8_t at_lun; /* lun or reserved */ 2139 uint8_t at_iid; /* initiator */ 2140 uint16_t at_rxid; /* response ID */ 2141 uint16_t at_flags; 2142 uint16_t at_status; /* firmware status */ 2143 uint8_t at_crn; /* command reference number */ 2144 uint8_t at_taskcodes; 2145 uint8_t at_taskflags; 2146 uint8_t at_execodes; 2147 uint8_t at_cdb[ATIO2_CDBLEN]; /* received CDB */ 2148 uint32_t at_datalen; /* allocated data len */ 2149 uint16_t at_scclun; /* SCC Lun or reserved */ 2150 uint16_t at_wwpn[4]; /* WWPN of initiator */ 2151 uint16_t at_reserved2[6]; 2152 uint16_t at_oxid; 2153 } at2_entry_t; 2154 2155 typedef struct { 2156 isphdr_t at_header; 2157 uint32_t at_reserved; 2158 uint16_t at_iid; /* initiator */ 2159 uint16_t at_rxid; /* response ID */ 2160 uint16_t at_flags; 2161 uint16_t at_status; /* firmware status */ 2162 uint8_t at_crn; /* command reference number */ 2163 uint8_t at_taskcodes; 2164 uint8_t at_taskflags; 2165 uint8_t at_execodes; 2166 uint8_t at_cdb[ATIO2_CDBLEN]; /* received CDB */ 2167 uint32_t at_datalen; /* allocated data len */ 2168 uint16_t at_scclun; /* SCC Lun or reserved */ 2169 uint16_t at_wwpn[4]; /* WWPN of initiator */ 2170 uint16_t at_reserved2[6]; 2171 uint16_t at_oxid; 2172 } at2e_entry_t; 2173 2174 #define ATIO2_WWPN_OFFSET 0x2A 2175 #define ATIO2_OXID_OFFSET 0x3E 2176 2177 #define ATIO2_TC_ATTR_MASK 0x7 2178 #define ATIO2_TC_ATTR_SIMPLEQ 0 2179 #define ATIO2_TC_ATTR_HEADOFQ 1 2180 #define ATIO2_TC_ATTR_ORDERED 2 2181 #define ATIO2_TC_ATTR_ACAQ 4 2182 #define ATIO2_TC_ATTR_UNTAGGED 5 2183 2184 #define ATIO2_EX_WRITE 0x1 2185 #define ATIO2_EX_READ 0x2 2186 /* 2187 * Macros to create and fetch and test concatenated handle and tag value macros 2188 */ 2189 #define AT2_MAKE_TAGID(tid, bus, inst, aep) \ 2190 tid = aep->at_rxid; \ 2191 tid |= (((uint64_t)inst) << 32); \ 2192 tid |= (((uint64_t)bus) << 48) 2193 2194 #define CT2_MAKE_TAGID(tid, bus, inst, ct) \ 2195 tid = ct->ct_rxid; \ 2196 tid |= (((uint64_t)inst) << 32); \ 2197 tid |= (((uint64_t)(bus & 0xff)) << 48) 2198 2199 #define AT2_HAS_TAG(val) 1 2200 #define AT2_GET_TAG(val) ((val) & 0xffffffff) 2201 #define AT2_GET_INST(val) (((val) >> 32) & 0xffff) 2202 #define AT2_GET_HANDLE AT2_GET_TAG 2203 #define AT2_GET_BUS(val) (((val) >> 48) & 0xff) 2204 2205 #define FC_HAS_TAG AT2_HAS_TAG 2206 #define FC_GET_TAG AT2_GET_TAG 2207 #define FC_GET_INST AT2_GET_INST 2208 #define FC_GET_HANDLE AT2_GET_HANDLE 2209 2210 #define IN_FC_MAKE_TAGID(tid, bus, inst, seqid) \ 2211 tid = seqid; \ 2212 tid |= (((uint64_t)inst) << 32); \ 2213 tid |= (((uint64_t)(bus & 0xff)) << 48) 2214 2215 #define FC_TAG_INSERT_INST(tid, inst) \ 2216 tid &= ~0x0000ffff00000000ull; \ 2217 tid |= (((uint64_t)inst) << 32) 2218 2219 /* 2220 * 24XX ATIO Definition 2221 * 2222 * This is *quite* different from other entry types. 2223 * First of all, it has its own queue it comes in on. 2224 * 2225 * Secondly, it doesn't have a normal header. 2226 * 2227 * Thirdly, it's just a passthru of the FCP CMND IU 2228 * which is recorded in big endian mode. 2229 */ 2230 typedef struct { 2231 uint8_t at_type; 2232 uint8_t at_count; 2233 /* 2234 * Task attribute in high four bits, 2235 * the rest is the FCP CMND IU Length. 2236 * NB: the command can extend past the 2237 * length for a single queue entry. 2238 */ 2239 uint16_t at_ta_len; 2240 uint32_t at_rxid; 2241 fc_hdr_t at_hdr; 2242 fcp_cmnd_iu_t at_cmnd; 2243 } at7_entry_t; 2244 #define AT7_NORESRC_RXID 0xffffffff 2245 2246 2247 /* 2248 * Continue Target I/O Entry structure 2249 * Request from driver. The response from the 2250 * ISP firmware is the same except that the last 18 2251 * bytes are overwritten by suggested sense data if 2252 * the 'autosense valid' bit is set in the status byte. 2253 */ 2254 typedef struct { 2255 isphdr_t ct_header; 2256 uint16_t ct_syshandle; 2257 uint16_t ct_fwhandle; /* required by f/w */ 2258 uint8_t ct_lun; /* lun */ 2259 uint8_t ct_iid; /* initiator id */ 2260 uint8_t ct_reserved2; 2261 uint8_t ct_tgt; /* our target id */ 2262 uint32_t ct_flags; 2263 uint8_t ct_status; /* isp status */ 2264 uint8_t ct_scsi_status; /* scsi status */ 2265 uint8_t ct_tag_val; /* tag value */ 2266 uint8_t ct_tag_type; /* tag type */ 2267 uint32_t ct_xfrlen; /* transfer length */ 2268 uint32_t ct_resid; /* residual length */ 2269 uint16_t ct_timeout; 2270 uint16_t ct_seg_count; 2271 ispds_t ct_dataseg[ISP_RQDSEG]; 2272 } ct_entry_t; 2273 2274 /* 2275 * For some of the dual port SCSI adapters, port (bus #) is reported 2276 * in the MSbit of ct_iid. Bit fields are a bit too awkward here. 2277 * 2278 * Note that this does not apply to FC adapters at all which can and 2279 * do report IIDs between 0x81 && 0xfe (or 0x7ff) which represent devices 2280 * that have logged in across a SCSI fabric. 2281 */ 2282 #define GET_IID_VAL(x) (x & 0x3f) 2283 #define GET_BUS_VAL(x) ((x >> 7) & 0x1) 2284 #define SET_IID_VAL(y, x) y = ((y & ~0x3f) | (x & 0x3f)) 2285 #define SET_BUS_VAL(y, x) y = ((y & 0x3f) | ((x & 0x1) << 7)) 2286 2287 /* 2288 * ct_flags values 2289 */ 2290 #define CT_TQAE 0x00000002 /* bit 1, Tagged Queue Action enable */ 2291 #define CT_DATA_IN 0x00000040 /* bits 6&7, Data direction - *to* initiator */ 2292 #define CT_DATA_OUT 0x00000080 /* bits 6&7, Data direction - *from* initiator */ 2293 #define CT_NO_DATA 0x000000C0 /* bits 6&7, Data direction */ 2294 #define CT_CCINCR 0x00000100 /* bit 8, autoincrement atio count */ 2295 #define CT_DATAMASK 0x000000C0 /* bits 6&7, Data direction */ 2296 #define CT_INISYNCWIDE 0x00004000 /* bit 14, Do Sync/Wide Negotiation */ 2297 #define CT_NODISC 0x00008000 /* bit 15, Disconnects disabled */ 2298 #define CT_DSDP 0x01000000 /* bit 24, Disable Save Data Pointers */ 2299 #define CT_SENDRDP 0x04000000 /* bit 26, Send Restore Pointers msg */ 2300 #define CT_SENDSTATUS 0x80000000 /* bit 31, Send SCSI status byte */ 2301 2302 /* 2303 * ct_status values 2304 * - set by the firmware when it returns the CTIO 2305 */ 2306 #define CT_OK 0x01 /* completed without error */ 2307 #define CT_ABORTED 0x02 /* aborted by host */ 2308 #define CT_ERR 0x04 /* see sense data for error */ 2309 #define CT_INVAL 0x06 /* request for disabled lun */ 2310 #define CT_NOPATH 0x07 /* invalid ITL nexus */ 2311 #define CT_INVRXID 0x08 /* (FC only) Invalid RX_ID */ 2312 #define CT_DATA_OVER 0x09 /* (FC only) Data Overrun */ 2313 #define CT_RSELTMO 0x0A /* reselection timeout after 2 tries */ 2314 #define CT_TIMEOUT 0x0B /* timed out */ 2315 #define CT_RESET 0x0E /* SCSI Bus Reset occurred */ 2316 #define CT_PARITY 0x0F /* Uncorrectable Parity Error */ 2317 #define CT_BUS_ERROR 0x10 /* (FC Only) DMA PCI Error */ 2318 #define CT_PANIC 0x13 /* Unrecoverable Error */ 2319 #define CT_PHASE_ERROR 0x14 /* Bus phase sequence error */ 2320 #define CT_DATA_UNDER 0x15 /* (FC only) Data Underrun */ 2321 #define CT_BDR_MSG 0x17 /* Bus Device Reset msg received */ 2322 #define CT_TERMINATED 0x19 /* due to Terminate Transfer mbox cmd */ 2323 #define CT_PORTUNAVAIL 0x28 /* port not available */ 2324 #define CT_LOGOUT 0x29 /* port logout */ 2325 #define CT_PORTCHANGED 0x2A /* port changed */ 2326 #define CT_IDE 0x33 /* Initiator Detected Error */ 2327 #define CT_NOACK 0x35 /* Outstanding Immed. Notify. entry */ 2328 #define CT_SRR 0x45 /* SRR Received */ 2329 #define CT_LUN_RESET 0x48 /* Lun Reset Received */ 2330 2331 #define CT_HBA_RESET 0xffff /* pseudo error - command destroyed by HBA reset*/ 2332 2333 /* 2334 * When the firmware returns a CTIO entry, it may overwrite the last 2335 * part of the structure with sense data. This starts at offset 0x2E 2336 * into the entry, which is in the middle of ct_dataseg[1]. Rather 2337 * than define a new struct for this, I'm just using the sense data 2338 * offset. 2339 */ 2340 #define CTIO_SENSE_OFFSET 0x2E 2341 2342 /* 2343 * Entry length in u_longs. All entries are the same size so 2344 * any one will do as the numerator. 2345 */ 2346 #define UINT32_ENTRY_SIZE (sizeof(at_entry_t)/sizeof(uint32_t)) 2347 2348 /* 2349 * QLA2100 CTIO (type 2) entry 2350 */ 2351 #define MAXRESPLEN 26 2352 typedef struct { 2353 isphdr_t ct_header; 2354 uint32_t ct_syshandle; 2355 uint8_t ct_lun; /* lun */ 2356 uint8_t ct_iid; /* initiator id */ 2357 uint16_t ct_rxid; /* response ID */ 2358 uint16_t ct_flags; 2359 uint16_t ct_status; /* isp status */ 2360 uint16_t ct_timeout; 2361 uint16_t ct_seg_count; 2362 uint32_t ct_reloff; /* relative offset */ 2363 uint32_t ct_resid; /* residual length */ 2364 union { 2365 /* 2366 * The three different modes that the target driver 2367 * can set the CTIO{2,3,4} up as. 2368 * 2369 * The first is for sending FCP_DATA_IUs as well as 2370 * (optionally) sending a terminal SCSI status FCP_RSP_IU. 2371 * 2372 * The second is for sending SCSI sense data in an FCP_RSP_IU. 2373 * Note that no FCP_DATA_IUs will be sent. 2374 * 2375 * The third is for sending FCP_RSP_IUs as built specifically 2376 * in system memory as located by the isp_dataseg. 2377 */ 2378 struct { 2379 uint32_t _reserved; 2380 uint16_t _reserved2; 2381 uint16_t ct_scsi_status; 2382 uint32_t ct_xfrlen; 2383 union { 2384 ispds_t ct_dataseg[ISP_RQDSEG_T2]; 2385 ispds64_t ct_dataseg64[ISP_RQDSEG_T3]; 2386 ispdslist_t ct_dslist; 2387 } u; 2388 } m0; 2389 struct { 2390 uint16_t _reserved; 2391 uint16_t _reserved2; 2392 uint16_t ct_senselen; 2393 uint16_t ct_scsi_status; 2394 uint16_t ct_resplen; 2395 uint8_t ct_resp[MAXRESPLEN]; 2396 } m1; 2397 struct { 2398 uint32_t _reserved; 2399 uint16_t _reserved2; 2400 uint16_t _reserved3; 2401 uint32_t ct_datalen; 2402 union { 2403 ispds_t ct_fcp_rsp_iudata_32; 2404 ispds64_t ct_fcp_rsp_iudata_64; 2405 } u; 2406 } m2; 2407 } rsp; 2408 } ct2_entry_t; 2409 2410 typedef struct { 2411 isphdr_t ct_header; 2412 uint32_t ct_syshandle; 2413 uint16_t ct_iid; /* initiator id */ 2414 uint16_t ct_rxid; /* response ID */ 2415 uint16_t ct_flags; 2416 uint16_t ct_status; /* isp status */ 2417 uint16_t ct_timeout; 2418 uint16_t ct_seg_count; 2419 uint32_t ct_reloff; /* relative offset */ 2420 uint32_t ct_resid; /* residual length */ 2421 union { 2422 struct { 2423 uint32_t _reserved; 2424 uint16_t _reserved2; 2425 uint16_t ct_scsi_status; 2426 uint32_t ct_xfrlen; 2427 union { 2428 ispds_t ct_dataseg[ISP_RQDSEG_T2]; 2429 ispds64_t ct_dataseg64[ISP_RQDSEG_T3]; 2430 ispdslist_t ct_dslist; 2431 } u; 2432 } m0; 2433 struct { 2434 uint16_t _reserved; 2435 uint16_t _reserved2; 2436 uint16_t ct_senselen; 2437 uint16_t ct_scsi_status; 2438 uint16_t ct_resplen; 2439 uint8_t ct_resp[MAXRESPLEN]; 2440 } m1; 2441 struct { 2442 uint32_t _reserved; 2443 uint16_t _reserved2; 2444 uint16_t _reserved3; 2445 uint32_t ct_datalen; 2446 union { 2447 ispds_t ct_fcp_rsp_iudata_32; 2448 ispds64_t ct_fcp_rsp_iudata_64; 2449 } u; 2450 } m2; 2451 } rsp; 2452 } ct2e_entry_t; 2453 2454 /* 2455 * ct_flags values for CTIO2 2456 */ 2457 #define CT2_FLAG_MODE0 0x0000 2458 #define CT2_FLAG_MODE1 0x0001 2459 #define CT2_FLAG_MODE2 0x0002 2460 #define CT2_FLAG_MMASK 0x0003 2461 #define CT2_DATA_IN 0x0040 /* *to* initiator */ 2462 #define CT2_DATA_OUT 0x0080 /* *from* initiator */ 2463 #define CT2_NO_DATA 0x00C0 2464 #define CT2_DATAMASK 0x00C0 2465 #define CT2_CCINCR 0x0100 2466 #define CT2_FASTPOST 0x0200 2467 #define CT2_CONFIRM 0x2000 2468 #define CT2_TERMINATE 0x4000 2469 #define CT2_SENDSTATUS 0x8000 2470 2471 /* 2472 * ct_status values are (mostly) the same as that for ct_entry. 2473 */ 2474 2475 /* 2476 * ct_scsi_status values- the low 8 bits are the normal SCSI status 2477 * we know and love. The upper 8 bits are validity markers for FCP_RSP_IU 2478 * fields. 2479 */ 2480 #define CT2_RSPLEN_VALID 0x0100 2481 #define CT2_SNSLEN_VALID 0x0200 2482 #define CT2_DATA_OVER 0x0400 2483 #define CT2_DATA_UNDER 0x0800 2484 2485 /* 2486 * ISP24XX CTIO 2487 */ 2488 #define MAXRESPLEN_24XX 24 2489 typedef struct { 2490 isphdr_t ct_header; 2491 uint32_t ct_syshandle; 2492 uint16_t ct_nphdl; /* status on returned CTIOs */ 2493 uint16_t ct_timeout; 2494 uint16_t ct_seg_count; 2495 uint8_t ct_vpidx; 2496 uint8_t ct_xflags; 2497 uint16_t ct_iid_lo; /* low 16 bits of portid */ 2498 uint8_t ct_iid_hi; /* hi 8 bits of portid */ 2499 uint8_t ct_reserved; 2500 uint32_t ct_rxid; 2501 uint16_t ct_senselen; /* mode 1 only */ 2502 uint16_t ct_flags; 2503 uint32_t ct_resid; /* residual length */ 2504 uint16_t ct_oxid; 2505 uint16_t ct_scsi_status; /* modes 0 && 1 only */ 2506 union { 2507 struct { 2508 uint32_t reloff; 2509 uint32_t reserved0; 2510 uint32_t ct_xfrlen; 2511 uint32_t reserved1; 2512 ispds64_t ds; 2513 } m0; 2514 struct { 2515 uint16_t ct_resplen; 2516 uint16_t reserved; 2517 uint8_t ct_resp[MAXRESPLEN_24XX]; 2518 } m1; 2519 struct { 2520 uint32_t reserved0; 2521 uint32_t reserved1; 2522 uint32_t ct_datalen; 2523 uint32_t reserved2; 2524 ispds64_t ct_fcp_rsp_iudata; 2525 } m2; 2526 } rsp; 2527 } ct7_entry_t; 2528 2529 /* 2530 * ct_flags values for CTIO7 2531 */ 2532 #define CT7_NO_DATA 0x0000 2533 #define CT7_DATA_OUT 0x0001 /* *from* initiator */ 2534 #define CT7_DATA_IN 0x0002 /* *to* initiator */ 2535 #define CT7_DATAMASK 0x3 2536 #define CT7_DSD_ENABLE 0x0004 2537 #define CT7_CONF_STSFD 0x0010 2538 #define CT7_EXPLCT_CONF 0x0020 2539 #define CT7_FLAG_MODE0 0x0000 2540 #define CT7_FLAG_MODE1 0x0040 2541 #define CT7_FLAG_MODE2 0x0080 2542 #define CT7_FLAG_MMASK 0x00C0 2543 #define CT7_NOACK 0x0100 2544 #define CT7_TASK_ATTR_SHIFT 9 2545 #define CT7_CONFIRM 0x2000 2546 #define CT7_TERMINATE 0x4000 2547 #define CT7_SENDSTATUS 0x8000 2548 2549 /* 2550 * Type 7 CTIO status codes 2551 */ 2552 #define CT7_OK 0x01 /* completed without error */ 2553 #define CT7_ABORTED 0x02 /* aborted by host */ 2554 #define CT7_ERR 0x04 /* see sense data for error */ 2555 #define CT7_INVAL 0x06 /* request for disabled lun */ 2556 #define CT7_INVRXID 0x08 /* Invalid RX_ID */ 2557 #define CT7_DATA_OVER 0x09 /* Data Overrun */ 2558 #define CT7_TIMEOUT 0x0B /* timed out */ 2559 #define CT7_RESET 0x0E /* LIP Rset Received */ 2560 #define CT7_BUS_ERROR 0x10 /* DMA PCI Error */ 2561 #define CT7_REASSY_ERR 0x11 /* DMA reassembly error */ 2562 #define CT7_DATA_UNDER 0x15 /* Data Underrun */ 2563 #define CT7_PORTUNAVAIL 0x28 /* port not available */ 2564 #define CT7_LOGOUT 0x29 /* port logout */ 2565 #define CT7_PORTCHANGED 0x2A /* port changed */ 2566 #define CT7_SRR 0x45 /* SRR Received */ 2567 2568 /* 2569 * Other 24XX related target IOCBs 2570 */ 2571 2572 /* 2573 * ABTS Received 2574 */ 2575 typedef struct { 2576 isphdr_t abts_header; 2577 uint8_t abts_reserved0[6]; 2578 uint16_t abts_nphdl; 2579 uint16_t abts_reserved1; 2580 uint16_t abts_sof; 2581 uint32_t abts_rxid_abts; 2582 uint16_t abts_did_lo; 2583 uint8_t abts_did_hi; 2584 uint8_t abts_r_ctl; 2585 uint16_t abts_sid_lo; 2586 uint8_t abts_sid_hi; 2587 uint8_t abts_cs_ctl; 2588 uint16_t abts_fs_ctl; 2589 uint8_t abts_f_ctl; 2590 uint8_t abts_type; 2591 uint16_t abts_seq_cnt; 2592 uint8_t abts_df_ctl; 2593 uint8_t abts_seq_id; 2594 uint16_t abts_rx_id; 2595 uint16_t abts_ox_id; 2596 uint32_t abts_param; 2597 uint8_t abts_reserved2[16]; 2598 uint32_t abts_rxid_task; 2599 } abts_t; 2600 2601 typedef struct { 2602 isphdr_t abts_rsp_header; 2603 uint32_t abts_rsp_handle; 2604 uint16_t abts_rsp_status; 2605 uint16_t abts_rsp_nphdl; 2606 uint16_t abts_rsp_ctl_flags; 2607 uint16_t abts_rsp_sof; 2608 uint32_t abts_rsp_rxid_abts; 2609 uint16_t abts_rsp_did_lo; 2610 uint8_t abts_rsp_did_hi; 2611 uint8_t abts_rsp_r_ctl; 2612 uint16_t abts_rsp_sid_lo; 2613 uint8_t abts_rsp_sid_hi; 2614 uint8_t abts_rsp_cs_ctl; 2615 uint16_t abts_rsp_f_ctl_lo; 2616 uint8_t abts_rsp_f_ctl_hi; 2617 uint8_t abts_rsp_type; 2618 uint16_t abts_rsp_seq_cnt; 2619 uint8_t abts_rsp_df_ctl; 2620 uint8_t abts_rsp_seq_id; 2621 uint16_t abts_rsp_rx_id; 2622 uint16_t abts_rsp_ox_id; 2623 uint32_t abts_rsp_param; 2624 union { 2625 struct { 2626 uint16_t reserved; 2627 uint8_t last_seq_id; 2628 uint8_t seq_id_valid; 2629 uint16_t aborted_rx_id; 2630 uint16_t aborted_ox_id; 2631 uint16_t high_seq_cnt; 2632 uint16_t low_seq_cnt; 2633 uint8_t reserved2[4]; 2634 } ba_acc; 2635 struct { 2636 uint8_t vendor_unique; 2637 uint8_t explanation; 2638 uint8_t reason; 2639 uint8_t reserved; 2640 uint8_t reserved2[12]; 2641 } ba_rjt; 2642 struct { 2643 uint8_t reserved[8]; 2644 uint32_t subcode1; 2645 uint32_t subcode2; 2646 } rsp; 2647 uint8_t reserved[16]; 2648 } abts_rsp_payload; 2649 uint32_t abts_rsp_rxid_task; 2650 } abts_rsp_t; 2651 2652 /* terminate this ABTS exchange */ 2653 #define ISP24XX_ABTS_RSP_TERMINATE 0x01 2654 2655 #define ISP24XX_ABTS_RSP_COMPLETE 0x00 2656 #define ISP24XX_ABTS_RSP_RESET 0x04 2657 #define ISP24XX_ABTS_RSP_ABORTED 0x05 2658 #define ISP24XX_ABTS_RSP_TIMEOUT 0x06 2659 #define ISP24XX_ABTS_RSP_INVXID 0x08 2660 #define ISP24XX_ABTS_RSP_LOGOUT 0x29 2661 #define ISP24XX_ABTS_RSP_SUBCODE 0x31 2662 2663 #define ISP24XX_NO_TASK 0xffffffff 2664 2665 /* 2666 * Miscellaneous 2667 * 2668 * These are the limits of the number of dma segments we 2669 * can deal with based not on the size of the segment counter 2670 * (which is 16 bits), but on the size of the number of 2671 * queue entries field (which is 8 bits). We assume no 2672 * segments in the first queue entry, so we can either 2673 * have 7 dma segments per continuation entry or 5 2674 * (for 64 bit dma).. multiplying out by 254.... 2675 */ 2676 #define ISP_NSEG_MAX 1778 2677 #define ISP_NSEG64_MAX 1270 2678 2679 #endif /* _ISPMBOX_H */ 2680