1 /* $FreeBSD$ */ 2 /* 3 * Qlogic Target Mode Structure and Flag Definitions 4 * 5 * Copyright (c) 1997, 1998 6 * Patrick Stirling 7 * pms@psconsult.com 8 * All rights reserved. 9 * 10 * Additional Copyright (c) 1999, 2000, 2001 11 * Matthew Jacob 12 * mjacob@feral.com 13 * All rights reserved. 14 * 15 * 16 * Redistribution and use in source and binary forms, with or without 17 * modification, are permitted provided that the following conditions 18 * are met: 19 * 1. Redistributions of source code must retain the above copyright 20 * notice immediately at the beginning of the file, without modification, 21 * this list of conditions, and the following disclaimer. 22 * 2. The name of the author may not be used to endorse or promote products 23 * derived from this software without specific prior written permission. 24 * 25 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 26 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 27 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 28 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR 29 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 30 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 31 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 32 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 33 * SUCH DAMAGE. 34 * 35 */ 36 #ifndef _ISP_TARGET_H 37 #define _ISP_TARGET_H 38 39 #define QLTM_SENSELEN 18 /* non-FC cards only */ 40 #define QLTM_SVALID 0x80 41 42 /* 43 * Structure for Enable Lun and Modify Lun queue entries 44 */ 45 typedef struct { 46 isphdr_t le_header; 47 u_int32_t le_reserved; 48 u_int8_t le_lun; 49 u_int8_t le_rsvd; 50 u_int8_t le_ops; /* Modify LUN only */ 51 u_int8_t le_tgt; /* Not for FC */ 52 u_int32_t le_flags; /* Not for FC */ 53 u_int8_t le_status; 54 u_int8_t le_reserved2; 55 u_int8_t le_cmd_count; 56 u_int8_t le_in_count; 57 u_int8_t le_cdb6len; /* Not for FC */ 58 u_int8_t le_cdb7len; /* Not for FC */ 59 u_int16_t le_timeout; 60 u_int16_t le_reserved3[20]; 61 } lun_entry_t; 62 63 /* 64 * le_flags values 65 */ 66 #define LUN_TQAE 0x00000002 /* bit1 Tagged Queue Action Enable */ 67 #define LUN_DSSM 0x01000000 /* bit24 Disable Sending SDP Message */ 68 #define LUN_DISAD 0x02000000 /* bit25 Disable autodisconnect */ 69 #define LUN_DM 0x40000000 /* bit30 Disconnects Mandatory */ 70 71 /* 72 * le_ops values 73 */ 74 #define LUN_CCINCR 0x01 /* increment command count */ 75 #define LUN_CCDECR 0x02 /* decrement command count */ 76 #define LUN_ININCR 0x40 /* increment immed. notify count */ 77 #define LUN_INDECR 0x80 /* decrement immed. notify count */ 78 79 /* 80 * le_status values 81 */ 82 #define LUN_OK 0x01 /* we be rockin' */ 83 #define LUN_ERR 0x04 /* request completed with error */ 84 #define LUN_INVAL 0x06 /* invalid request */ 85 #define LUN_NOCAP 0x16 /* can't provide requested capability */ 86 #define LUN_ENABLED 0x3E /* LUN already enabled */ 87 88 /* 89 * Immediate Notify Entry structure 90 */ 91 #define IN_MSGLEN 8 /* 8 bytes */ 92 #define IN_RSVDLEN 8 /* 8 words */ 93 typedef struct { 94 isphdr_t in_header; 95 u_int32_t in_reserved; 96 u_int8_t in_lun; /* lun */ 97 u_int8_t in_iid; /* initiator */ 98 u_int8_t in_reserved2; 99 u_int8_t in_tgt; /* target */ 100 u_int32_t in_flags; 101 u_int8_t in_status; 102 u_int8_t in_rsvd2; 103 u_int8_t in_tag_val; /* tag value */ 104 u_int8_t in_tag_type; /* tag type */ 105 u_int16_t in_seqid; /* sequence id */ 106 u_int8_t in_msg[IN_MSGLEN]; /* SCSI message bytes */ 107 u_int16_t in_reserved3[IN_RSVDLEN]; 108 u_int8_t in_sense[QLTM_SENSELEN];/* suggested sense data */ 109 } in_entry_t; 110 111 typedef struct { 112 isphdr_t in_header; 113 u_int32_t in_reserved; 114 u_int8_t in_lun; /* lun */ 115 u_int8_t in_iid; /* initiator */ 116 u_int16_t in_scclun; 117 u_int32_t in_reserved2; 118 u_int16_t in_status; 119 u_int16_t in_task_flags; 120 u_int16_t in_seqid; /* sequence id */ 121 } in_fcentry_t; 122 123 /* 124 * Values for the in_status field 125 */ 126 #define IN_REJECT 0x0D /* Message Reject message received */ 127 #define IN_RESET 0x0E /* Bus Reset occurred */ 128 #define IN_NO_RCAP 0x16 /* requested capability not available */ 129 #define IN_IDE_RECEIVED 0x33 /* Initiator Detected Error msg received */ 130 #define IN_RSRC_UNAVAIL 0x34 /* resource unavailable */ 131 #define IN_MSG_RECEIVED 0x36 /* SCSI message received */ 132 #define IN_ABORT_TASK 0x20 /* task named in RX_ID is being aborted (FC) */ 133 #define IN_PORT_LOGOUT 0x29 /* port has logged out (FC) */ 134 #define IN_PORT_CHANGED 0x2A /* port changed */ 135 #define IN_GLOBAL_LOGO 0x2E /* all ports logged out */ 136 #define IN_NO_NEXUS 0x3B /* Nexus not established */ 137 138 /* 139 * Values for the in_task_flags field- should only get one at a time! 140 */ 141 #define TASK_FLAGS_CLEAR_ACA (1<<14) 142 #define TASK_FLAGS_TARGET_RESET (1<<13) 143 #define TASK_FLAGS_LUN_RESET (1<<12) 144 #define TASK_FLAGS_CLEAR_TASK_SET (1<<10) 145 #define TASK_FLAGS_ABORT_TASK_SET (1<<9) 146 147 #ifndef MSG_ABORT 148 #define MSG_ABORT 0x06 149 #endif 150 #ifndef MSG_BUS_DEV_RESET 151 #define MSG_BUS_DEV_RESET 0x0c 152 #endif 153 #ifndef MSG_ABORT_TAG 154 #define MSG_ABORT_TAG 0x0d 155 #endif 156 #ifndef MSG_CLEAR_QUEUE 157 #define MSG_CLEAR_QUEUE 0x0e 158 #endif 159 #ifndef MSG_REL_RECOVERY 160 #define MSG_REL_RECOVERY 0x10 161 #endif 162 #ifndef MSG_TERM_IO_PROC 163 #define MSG_TERM_IO_PROC 0x11 164 #endif 165 #ifndef MSG_LUN_RESET 166 #define MSG_LUN_RESET 0x17 167 #endif 168 169 /* 170 * Notify Acknowledge Entry structure 171 */ 172 #define NA_RSVDLEN 22 173 typedef struct { 174 isphdr_t na_header; 175 u_int32_t na_reserved; 176 u_int8_t na_lun; /* lun */ 177 u_int8_t na_iid; /* initiator */ 178 u_int8_t na_reserved2; 179 u_int8_t na_tgt; /* target */ 180 u_int32_t na_flags; 181 u_int8_t na_status; 182 u_int8_t na_event; 183 u_int16_t na_seqid; /* sequence id */ 184 u_int16_t na_reserved3[NA_RSVDLEN]; 185 } na_entry_t; 186 187 /* 188 * Value for the na_event field 189 */ 190 #define NA_RST_CLRD 0x80 /* Clear an async event notification */ 191 #define NA_OK 0x01 /* Notify Acknowledge Succeeded */ 192 #define NA_INVALID 0x06 /* Invalid Notify Acknowledge */ 193 194 #define NA2_RSVDLEN 21 195 typedef struct { 196 isphdr_t na_header; 197 u_int32_t na_reserved; 198 u_int8_t na_lun; /* lun */ 199 u_int8_t na_iid; /* initiator */ 200 u_int16_t na_scclun; 201 u_int16_t na_flags; 202 u_int16_t na_reserved2; 203 u_int16_t na_status; 204 u_int16_t na_task_flags; 205 u_int16_t na_seqid; /* sequence id */ 206 u_int16_t na_reserved3[NA2_RSVDLEN]; 207 } na_fcentry_t; 208 #define NAFC_RCOUNT 0x80 /* increment resource count */ 209 #define NAFC_RST_CLRD 0x20 /* Clear LIP Reset */ 210 /* 211 * Accept Target I/O Entry structure 212 */ 213 #define ATIO_CDBLEN 26 214 215 typedef struct { 216 isphdr_t at_header; 217 u_int16_t at_reserved; 218 u_int16_t at_handle; 219 u_int8_t at_lun; /* lun */ 220 u_int8_t at_iid; /* initiator */ 221 u_int8_t at_cdblen; /* cdb length */ 222 u_int8_t at_tgt; /* target */ 223 u_int32_t at_flags; 224 u_int8_t at_status; /* firmware status */ 225 u_int8_t at_scsi_status; /* scsi status */ 226 u_int8_t at_tag_val; /* tag value */ 227 u_int8_t at_tag_type; /* tag type */ 228 u_int8_t at_cdb[ATIO_CDBLEN]; /* received CDB */ 229 u_int8_t at_sense[QLTM_SENSELEN];/* suggested sense data */ 230 } at_entry_t; 231 232 /* 233 * at_flags values 234 */ 235 #define AT_NODISC 0x00008000 /* disconnect disabled */ 236 #define AT_TQAE 0x00000002 /* Tagged Queue Action enabled */ 237 238 /* 239 * at_status values 240 */ 241 #define AT_PATH_INVALID 0x07 /* ATIO sent to firmware for disabled lun */ 242 #define AT_RESET 0x0E /* SCSI Bus Reset Occurred */ 243 #define AT_PHASE_ERROR 0x14 /* Bus phase sequence error */ 244 #define AT_NOCAP 0x16 /* Requested capability not available */ 245 #define AT_BDR_MSG 0x17 /* Bus Device Reset msg received */ 246 #define AT_CDB 0x3D /* CDB received */ 247 248 /* 249 * Macros to create and fetch and test concatenated handle and tag value macros 250 */ 251 252 #define AT_MAKE_TAGID(tid, aep) \ 253 tid = ((aep)->at_handle << 16); \ 254 if ((aep)->at_flags & AT_TQAE) \ 255 (tid) |= ((aep)->at_tag_val + 1) 256 257 #define CT_MAKE_TAGID(tid, ct) \ 258 tid = ((ct)->ct_fwhandle << 16); \ 259 if ((ct)->ct_flags & CT_TQAE) \ 260 (tid) |= ((ct)->ct_tag_val + 1) 261 262 #define AT_HAS_TAG(val) ((val) & 0xffff) 263 #define AT_GET_TAG(val) AT_HAS_TAG(val) - 1 264 #define AT_GET_HANDLE(val) ((val) >> 16) 265 266 /* 267 * Accept Target I/O Entry structure, Type 2 268 */ 269 #define ATIO2_CDBLEN 16 270 271 typedef struct { 272 isphdr_t at_header; 273 u_int32_t at_reserved; 274 u_int8_t at_lun; /* lun or reserved */ 275 u_int8_t at_iid; /* initiator */ 276 u_int16_t at_rxid; /* response ID */ 277 u_int16_t at_flags; 278 u_int16_t at_status; /* firmware status */ 279 u_int8_t at_crn; /* command reference number */ 280 u_int8_t at_taskcodes; 281 u_int8_t at_taskflags; 282 u_int8_t at_execodes; 283 u_int8_t at_cdb[ATIO2_CDBLEN]; /* received CDB */ 284 u_int32_t at_datalen; /* allocated data len */ 285 u_int16_t at_scclun; /* SCC Lun or reserved */ 286 u_int16_t at_wwpn[4]; /* WWPN of initiator */ 287 u_int16_t at_reserved2[6]; 288 u_int16_t at_oxid; 289 } at2_entry_t; 290 291 #define ATIO2_WWPN_OFFSET 0x2A 292 #define ATIO2_OXID_OFFSET 0x3E 293 294 #define ATIO2_TC_ATTR_MASK 0x7 295 #define ATIO2_TC_ATTR_SIMPLEQ 0 296 #define ATIO2_TC_ATTR_HEADOFQ 1 297 #define ATIO2_TC_ATTR_ORDERED 2 298 #define ATIO2_TC_ATTR_ACAQ 4 299 #define ATIO2_TC_ATTR_UNTAGGED 5 300 301 #define ATIO2_EX_WRITE 0x1 302 #define ATIO2_EX_READ 0x2 303 304 /* 305 * Continue Target I/O Entry structure 306 * Request from driver. The response from the 307 * ISP firmware is the same except that the last 18 308 * bytes are overwritten by suggested sense data if 309 * the 'autosense valid' bit is set in the status byte. 310 */ 311 typedef struct { 312 isphdr_t ct_header; 313 u_int16_t ct_reserved; 314 #define ct_syshandle ct_reserved /* we use this */ 315 u_int16_t ct_fwhandle; /* required by f/w */ 316 u_int8_t ct_lun; /* lun */ 317 u_int8_t ct_iid; /* initiator id */ 318 u_int8_t ct_reserved2; 319 u_int8_t ct_tgt; /* our target id */ 320 u_int32_t ct_flags; 321 u_int8_t ct_status; /* isp status */ 322 u_int8_t ct_scsi_status; /* scsi status */ 323 u_int8_t ct_tag_val; /* tag value */ 324 u_int8_t ct_tag_type; /* tag type */ 325 u_int32_t ct_xfrlen; /* transfer length */ 326 u_int32_t ct_resid; /* residual length */ 327 u_int16_t ct_timeout; 328 u_int16_t ct_seg_count; 329 /* 330 * This is so we can share tag name space with 331 * CTIO{2,3,4} with the minimum of pain. 332 */ 333 union { 334 ispds_t ct_a[ISP_RQDSEG]; 335 } _u; 336 #define ct_dataseg _u.ct_a 337 } ct_entry_t; 338 339 /* 340 * For some of the dual port SCSI adapters, port (bus #) is reported 341 * in the MSbit of ct_iid. Bit fields are a bit too awkward here. 342 * 343 * Note that this does not apply to FC adapters at all which can and 344 * do report IIDs between 129 && 255 (these represent devices that have 345 * logged in across a SCSI fabric). 346 */ 347 #define GET_IID_VAL(x) (x & 0x3f) 348 #define GET_BUS_VAL(x) ((x >> 7) & 0x1) 349 #define SET_IID_VAL(y, x) y = ((y & ~0x3f) | (x & 0x3f)) 350 #define SET_BUS_VAL(y, x) y = ((y & 0x3f) | ((x & 0x1) << 7)) 351 352 /* 353 * ct_flags values 354 */ 355 #define CT_TQAE 0x00000002 /* bit 1, Tagged Queue Action enable */ 356 #define CT_DATA_IN 0x00000040 /* bits 6&7, Data direction */ 357 #define CT_DATA_OUT 0x00000080 /* bits 6&7, Data direction */ 358 #define CT_NO_DATA 0x000000C0 /* bits 6&7, Data direction */ 359 #define CT_CCINCR 0x00000100 /* bit 8, autoincrement atio count */ 360 #define CT_DATAMASK 0x000000C0 /* bits 6&7, Data direction */ 361 #define CT_INISYNCWIDE 0x00004000 /* bit 14, Do Sync/Wide Negotiation */ 362 #define CT_NODISC 0x00008000 /* bit 15, Disconnects disabled */ 363 #define CT_DSDP 0x01000000 /* bit 24, Disable Save Data Pointers */ 364 #define CT_SENDRDP 0x04000000 /* bit 26, Send Restore Pointers msg */ 365 #define CT_SENDSTATUS 0x80000000 /* bit 31, Send SCSI status byte */ 366 367 /* 368 * ct_status values 369 * - set by the firmware when it returns the CTIO 370 */ 371 #define CT_OK 0x01 /* completed without error */ 372 #define CT_ABORTED 0x02 /* aborted by host */ 373 #define CT_ERR 0x04 /* see sense data for error */ 374 #define CT_INVAL 0x06 /* request for disabled lun */ 375 #define CT_NOPATH 0x07 /* invalid ITL nexus */ 376 #define CT_INVRXID 0x08 /* (FC only) Invalid RX_ID */ 377 #define CT_DATA_OVER 0x09 /* (FC only) Data Overrun */ 378 #define CT_RSELTMO 0x0A /* reselection timeout after 2 tries */ 379 #define CT_TIMEOUT 0x0B /* timed out */ 380 #define CT_RESET 0x0E /* SCSI Bus Reset occurred */ 381 #define CT_PARITY 0x0F /* Uncorrectable Parity Error */ 382 #define CT_BUS_ERROR 0x10 /* (FC Only) DMA PCI Error */ 383 #define CT_PANIC 0x13 /* Unrecoverable Error */ 384 #define CT_PHASE_ERROR 0x14 /* Bus phase sequence error */ 385 #define CT_BDR_MSG 0x17 /* Bus Device Reset msg received */ 386 #define CT_DATA_UNDER 0x15 /* (FC only) Data Underrun */ 387 #define CT_TERMINATED 0x19 /* due to Terminate Transfer mbox cmd */ 388 #define CT_PORTNOTAVAIL 0x28 /* port not available */ 389 #define CT_LOGOUT 0x29 /* port logout */ 390 #define CT_PORTCHANGED 0x2A /* port changed */ 391 #define CT_IDE 0x33 /* Initiator Detected Error */ 392 #define CT_NOACK 0x35 /* Outstanding Immed. Notify. entry */ 393 394 /* 395 * When the firmware returns a CTIO entry, it may overwrite the last 396 * part of the structure with sense data. This starts at offset 0x2E 397 * into the entry, which is in the middle of ct_dataseg[1]. Rather 398 * than define a new struct for this, I'm just using the sense data 399 * offset. 400 */ 401 #define CTIO_SENSE_OFFSET 0x2E 402 403 /* 404 * Entry length in u_longs. All entries are the same size so 405 * any one will do as the numerator. 406 */ 407 #define UINT32_ENTRY_SIZE (sizeof(at_entry_t)/sizeof(u_int32_t)) 408 409 /* 410 * QLA2100 CTIO (type 2) entry 411 */ 412 #define MAXRESPLEN 26 413 typedef struct { 414 isphdr_t ct_header; 415 u_int16_t ct_reserved; 416 u_int16_t ct_fwhandle; /* just to match CTIO */ 417 u_int8_t ct_lun; /* lun */ 418 u_int8_t ct_iid; /* initiator id */ 419 u_int16_t ct_rxid; /* response ID */ 420 u_int16_t ct_flags; 421 u_int16_t ct_status; /* isp status */ 422 u_int16_t ct_timeout; 423 u_int16_t ct_seg_count; 424 u_int32_t ct_reloff; /* relative offset */ 425 int32_t ct_resid; /* residual length */ 426 union { 427 /* 428 * The three different modes that the target driver 429 * can set the CTIO{2,3,4} up as. 430 * 431 * The first is for sending FCP_DATA_IUs as well as 432 * (optionally) sending a terminal SCSI status FCP_RSP_IU. 433 * 434 * The second is for sending SCSI sense data in an FCP_RSP_IU. 435 * Note that no FCP_DATA_IUs will be sent. 436 * 437 * The third is for sending FCP_RSP_IUs as built specifically 438 * in system memory as located by the isp_dataseg. 439 */ 440 struct { 441 u_int32_t _reserved; 442 u_int16_t _reserved2; 443 u_int16_t ct_scsi_status; 444 u_int32_t ct_xfrlen; 445 union { 446 ispds_t ct_a[ISP_RQDSEG_T2]; /* CTIO2 */ 447 ispds64_t ct_b[ISP_RQDSEG_T3]; /* CTIO3 */ 448 ispdslist_t ct_c; /* CTIO4 */ 449 } _u; 450 #define ct_dataseg _u.ct_a 451 #define ct_dataseg64 _u.ct_b 452 #define ct_dslist _u.ct_c 453 } m0; 454 struct { 455 u_int16_t _reserved; 456 u_int16_t _reserved2; 457 u_int16_t ct_senselen; 458 u_int16_t ct_scsi_status; 459 u_int16_t ct_resplen; 460 u_int8_t ct_resp[MAXRESPLEN]; 461 } m1; 462 struct { 463 u_int32_t _reserved; 464 u_int16_t _reserved2; 465 u_int16_t _reserved3; 466 u_int32_t ct_datalen; 467 ispds_t ct_fcp_rsp_iudata; 468 } m2; 469 } rsp; 470 } ct2_entry_t; 471 472 /* 473 * ct_flags values for CTIO2 474 */ 475 #define CT2_FLAG_MMASK 0x0003 476 #define CT2_FLAG_MODE0 0x0000 477 #define CT2_FLAG_MODE1 0x0001 478 #define CT2_FLAG_MODE2 0x0002 479 #define CT2_DATA_IN CT_DATA_IN 480 #define CT2_DATA_OUT CT_DATA_OUT 481 #define CT2_NO_DATA CT_NO_DATA 482 #define CT2_DATAMASK CT_DATAMASK 483 #define CT2_CCINCR 0x0100 484 #define CT2_FASTPOST 0x0200 485 #define CT2_TERMINATE 0x4000 486 #define CT2_SENDSTATUS 0x8000 487 488 /* 489 * ct_status values are (mostly) the same as that for ct_entry. 490 */ 491 492 /* 493 * ct_scsi_status values- the low 8 bits are the normal SCSI status 494 * we know and love. The upper 8 bits are validity markers for FCP_RSP_IU 495 * fields. 496 */ 497 #define CT2_RSPLEN_VALID 0x0100 498 #define CT2_SNSLEN_VALID 0x0200 499 #define CT2_DATA_OVER 0x0400 500 #define CT2_DATA_UNDER 0x0800 501 502 /* 503 * Debug macros 504 */ 505 506 #define ISP_TDQE(isp, msg, idx, arg) \ 507 if (isp->isp_dblev & ISP_LOGTDEBUG2) isp_print_qentry(isp, msg, idx, arg) 508 509 #ifdef ISP_TARGET_FUNCTIONS 510 /* 511 * The functions below are for the publicly available 512 * target mode functions that are internal to the Qlogic driver. 513 */ 514 515 /* 516 * This function handles new response queue entry appropriate for target mode. 517 */ 518 int isp_target_notify(struct ispsoftc *, void *, u_int16_t *); 519 520 /* 521 * Enable/Disable/Modify a logical unit. 522 * (softc, cmd, bus, tgt, lun, cmd_cnt, inotify_cnt, opaque) 523 */ 524 #define DFLT_CMND_CNT 0xfe /* unmonitored */ 525 #define DFLT_INOT_CNT 16 526 int isp_lun_cmd(struct ispsoftc *, int, int, int, int, int, int, u_int32_t); 527 528 /* 529 * General request queue 'put' routine for target mode entries. 530 */ 531 int isp_target_put_entry(struct ispsoftc *isp, void *); 532 533 /* 534 * General routine to put back an ATIO entry- 535 * used for replenishing f/w resource counts. 536 * The argument is a pointer to a source ATIO 537 * or ATIO2. 538 */ 539 int isp_target_put_atio(struct ispsoftc *, void *); 540 541 /* 542 * General routine to send a final CTIO for a command- used mostly for 543 * local responses. 544 */ 545 int isp_endcmd(struct ispsoftc *, void *, u_int32_t, u_int16_t); 546 #define ECMD_SVALID 0x100 547 548 /* 549 * Handle an asynchronous event 550 * 551 * Return nonzero if the interrupt that generated this event has been dismissed. 552 */ 553 554 int isp_target_async(struct ispsoftc *, int, int); 555 #endif 556 #endif /* _ISP_TARGET_H */ 557