1 /*- 2 * SPDX-License-Identifier: BSD-2-Clause-FreeBSD 3 * 4 * Copyright (c) 1998, 2001 Nicolas Souchu 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions and the following disclaimer. 12 * 2. Redistributions in binary form must reproduce the above copyright 13 * notice, this list of conditions and the following disclaimer in the 14 * documentation and/or other materials provided with the distribution. 15 * 16 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 17 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 18 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 19 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 20 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 21 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 22 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 23 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 24 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 25 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 26 * SUCH DAMAGE. 27 */ 28 29 #include <sys/cdefs.h> 30 __FBSDID("$FreeBSD$"); 31 32 /* 33 * Generic I2C bit-banging code 34 * 35 * Example: 36 * 37 * iicbus 38 * / \ 39 * iicbb pcf 40 * | \ 41 * bti2c lpbb 42 * 43 * From Linux I2C generic interface 44 * (c) 1998 Gerd Knorr <kraxel@cs.tu-berlin.de> 45 * 46 */ 47 48 #include "opt_platform.h" 49 50 #include <sys/param.h> 51 #include <sys/kernel.h> 52 #include <sys/systm.h> 53 #include <sys/module.h> 54 #include <sys/bus.h> 55 #include <sys/sysctl.h> 56 #include <sys/uio.h> 57 58 #ifdef FDT 59 #include <dev/ofw/ofw_bus.h> 60 #include <dev/ofw/ofw_bus_subr.h> 61 #include <dev/fdt/fdt_common.h> 62 #endif 63 64 #include <dev/iicbus/iiconf.h> 65 #include <dev/iicbus/iicbus.h> 66 67 #include <dev/smbus/smbconf.h> 68 69 #include "iicbus_if.h" 70 #include "iicbb_if.h" 71 72 /* Based on the SMBus specification. */ 73 #define DEFAULT_SCL_LOW_TIMEOUT (25 * 1000) 74 75 struct iicbb_softc { 76 device_t iicbus; 77 u_int udelay; /* signal toggle delay in usec */ 78 u_int io_latency; /* approximate pin toggling latency */ 79 u_int scl_low_timeout; 80 }; 81 82 static int iicbb_attach(device_t); 83 static void iicbb_child_detached(device_t, device_t); 84 static int iicbb_detach(device_t); 85 static int iicbb_print_child(device_t, device_t); 86 static int iicbb_probe(device_t); 87 88 static int iicbb_callback(device_t, int, caddr_t); 89 static int iicbb_start(device_t, u_char, int); 90 static int iicbb_repstart(device_t, u_char, int); 91 static int iicbb_stop(device_t); 92 static int iicbb_write(device_t, const char *, int, int *, int); 93 static int iicbb_read(device_t, char *, int, int *, int, int); 94 static int iicbb_reset(device_t, u_char, u_char, u_char *); 95 static int iicbb_transfer(device_t dev, struct iic_msg *msgs, uint32_t nmsgs); 96 static void iicbb_set_speed(struct iicbb_softc *sc, u_char); 97 #ifdef FDT 98 static phandle_t iicbb_get_node(device_t, device_t); 99 #endif 100 101 static device_method_t iicbb_methods[] = { 102 /* device interface */ 103 DEVMETHOD(device_probe, iicbb_probe), 104 DEVMETHOD(device_attach, iicbb_attach), 105 DEVMETHOD(device_detach, iicbb_detach), 106 107 /* bus interface */ 108 DEVMETHOD(bus_child_detached, iicbb_child_detached), 109 DEVMETHOD(bus_print_child, iicbb_print_child), 110 111 /* iicbus interface */ 112 DEVMETHOD(iicbus_callback, iicbb_callback), 113 DEVMETHOD(iicbus_start, iicbb_start), 114 DEVMETHOD(iicbus_repeated_start, iicbb_repstart), 115 DEVMETHOD(iicbus_stop, iicbb_stop), 116 DEVMETHOD(iicbus_write, iicbb_write), 117 DEVMETHOD(iicbus_read, iicbb_read), 118 DEVMETHOD(iicbus_reset, iicbb_reset), 119 DEVMETHOD(iicbus_transfer, iicbb_transfer), 120 121 #ifdef FDT 122 /* ofw_bus interface */ 123 DEVMETHOD(ofw_bus_get_node, iicbb_get_node), 124 #endif 125 126 { 0, 0 } 127 }; 128 129 driver_t iicbb_driver = { 130 "iicbb", 131 iicbb_methods, 132 sizeof(struct iicbb_softc), 133 }; 134 135 static int 136 iicbb_probe(device_t dev) 137 { 138 device_set_desc(dev, "I2C bit-banging driver"); 139 140 return (0); 141 } 142 143 static int 144 iicbb_attach(device_t dev) 145 { 146 struct iicbb_softc *sc = (struct iicbb_softc *)device_get_softc(dev); 147 148 sc->iicbus = device_add_child(dev, "iicbus", -1); 149 if (!sc->iicbus) 150 return (ENXIO); 151 152 sc->scl_low_timeout = DEFAULT_SCL_LOW_TIMEOUT; 153 154 SYSCTL_ADD_UINT(device_get_sysctl_ctx(dev), 155 SYSCTL_CHILDREN(device_get_sysctl_tree(dev)), OID_AUTO, 156 "delay", CTLFLAG_RD, &sc->udelay, 157 0, "Signal change delay controlled by bus frequency, microseconds"); 158 159 SYSCTL_ADD_UINT(device_get_sysctl_ctx(dev), 160 SYSCTL_CHILDREN(device_get_sysctl_tree(dev)), OID_AUTO, 161 "scl_low_timeout", CTLFLAG_RWTUN, &sc->scl_low_timeout, 162 0, "SCL low timeout, microseconds"); 163 SYSCTL_ADD_UINT(device_get_sysctl_ctx(dev), 164 SYSCTL_CHILDREN(device_get_sysctl_tree(dev)), OID_AUTO, 165 "io_latency", CTLFLAG_RWTUN, &sc->io_latency, 166 0, "Estimate of pin toggling latency, microseconds"); 167 168 bus_generic_attach(dev); 169 return (0); 170 } 171 172 static int 173 iicbb_detach(device_t dev) 174 { 175 176 bus_generic_detach(dev); 177 device_delete_children(dev); 178 179 return (0); 180 } 181 182 #ifdef FDT 183 static phandle_t 184 iicbb_get_node(device_t bus, device_t dev) 185 { 186 187 /* We only have one child, the I2C bus, which needs our own node. */ 188 return (ofw_bus_get_node(bus)); 189 } 190 #endif 191 192 static void 193 iicbb_child_detached( device_t dev, device_t child ) 194 { 195 struct iicbb_softc *sc = (struct iicbb_softc *)device_get_softc(dev); 196 197 if (child == sc->iicbus) 198 sc->iicbus = NULL; 199 } 200 201 static int 202 iicbb_print_child(device_t bus, device_t dev) 203 { 204 int error; 205 int retval = 0; 206 u_char oldaddr; 207 208 retval += bus_print_child_header(bus, dev); 209 /* retrieve the interface I2C address */ 210 error = IICBB_RESET(device_get_parent(bus), IIC_FASTEST, 0, &oldaddr); 211 if (error == IIC_ENOADDR) { 212 retval += printf(" on %s master-only\n", 213 device_get_nameunit(bus)); 214 } else { 215 /* restore the address */ 216 IICBB_RESET(device_get_parent(bus), IIC_FASTEST, oldaddr, NULL); 217 218 retval += printf(" on %s addr 0x%x\n", 219 device_get_nameunit(bus), oldaddr & 0xff); 220 } 221 222 return (retval); 223 } 224 225 #define IICBB_DEBUG 226 #ifdef IICBB_DEBUG 227 static int i2c_debug = 0; 228 229 SYSCTL_DECL(_hw_i2c); 230 SYSCTL_INT(_hw_i2c, OID_AUTO, iicbb_debug, CTLFLAG_RWTUN, 231 &i2c_debug, 0, "Enable i2c bit-banging driver debug"); 232 233 #define I2C_DEBUG(x) do { \ 234 if (i2c_debug) (x); \ 235 } while (0) 236 #else 237 #define I2C_DEBUG(x) 238 #endif 239 240 #define I2C_GETSDA(dev) (IICBB_GETSDA(device_get_parent(dev))) 241 #define I2C_SETSDA(dev, x) (IICBB_SETSDA(device_get_parent(dev), x)) 242 #define I2C_GETSCL(dev) (IICBB_GETSCL(device_get_parent(dev))) 243 #define I2C_SETSCL(dev, x) (IICBB_SETSCL(device_get_parent(dev), x)) 244 245 static int 246 iicbb_waitforscl(device_t dev) 247 { 248 struct iicbb_softc *sc = device_get_softc(dev); 249 sbintime_t fast_timeout; 250 sbintime_t now, timeout; 251 252 /* Spin for up to 1 ms, then switch to pause. */ 253 now = sbinuptime(); 254 fast_timeout = now + SBT_1MS; 255 timeout = now + sc->scl_low_timeout * SBT_1US; 256 do { 257 if (I2C_GETSCL(dev)) 258 return (0); 259 now = sbinuptime(); 260 } while (now < fast_timeout); 261 do { 262 I2C_DEBUG(printf(".")); 263 pause_sbt("iicbb-scl-low", SBT_1MS, C_PREL(8), 0); 264 if (I2C_GETSCL(dev)) 265 return (0); 266 now = sbinuptime(); 267 } while (now < timeout); 268 269 I2C_DEBUG(printf("*")); 270 return (IIC_ETIMEOUT); 271 } 272 273 /* Start the high phase of the clock. */ 274 static int 275 iicbb_clockin(device_t dev, int sda) 276 { 277 278 /* 279 * Precondition: SCL is low. 280 * Action: 281 * - set SDA to the value; 282 * - release SCL and wait until it's high. 283 * The caller is responsible for keeping SCL high for udelay. 284 * 285 * There should be a data set-up time, 250 ns minimum, between setting 286 * SDA and raising SCL. It's expected that the I/O access latency will 287 * naturally provide that delay. 288 */ 289 I2C_SETSDA(dev, sda); 290 I2C_SETSCL(dev, 1); 291 return (iicbb_waitforscl(dev)); 292 } 293 294 /* 295 * End the high phase of the clock and wait out the low phase 296 * as nothing interesting happens during it anyway. 297 */ 298 static void 299 iicbb_clockout(device_t dev) 300 { 301 struct iicbb_softc *sc = device_get_softc(dev); 302 303 /* 304 * Precondition: SCL is high. 305 * Action: 306 * - pull SCL low and hold for udelay. 307 */ 308 I2C_SETSCL(dev, 0); 309 DELAY(sc->udelay); 310 } 311 312 static int 313 iicbb_sendbit(device_t dev, int bit) 314 { 315 struct iicbb_softc *sc = device_get_softc(dev); 316 int err; 317 318 err = iicbb_clockin(dev, bit); 319 if (err != 0) 320 return (err); 321 DELAY(sc->udelay); 322 iicbb_clockout(dev); 323 return (0); 324 } 325 326 /* 327 * Waiting for ACKNOWLEDGE. 328 * 329 * When a chip is being addressed or has received data it will issue an 330 * ACKNOWLEDGE pulse. Therefore the MASTER must release the DATA line 331 * (set it to high level) and then release the CLOCK line. 332 * Now it must wait for the SLAVE to pull the DATA line low. 333 * Actually on the bus this looks like a START condition so nothing happens 334 * because of the fact that the IC's that have not been addressed are doing 335 * nothing. 336 * 337 * When the SLAVE has pulled this line low the MASTER will take the CLOCK 338 * line low and then the SLAVE will release the SDA (data) line. 339 */ 340 static int 341 iicbb_getack(device_t dev) 342 { 343 struct iicbb_softc *sc = device_get_softc(dev); 344 int noack, err; 345 int t; 346 347 /* Release SDA so that the slave can drive it. */ 348 err = iicbb_clockin(dev, 1); 349 if (err != 0) { 350 I2C_DEBUG(printf("! ")); 351 return (err); 352 } 353 354 /* Sample SDA until ACK (low) or udelay runs out. */ 355 for (t = 0; t < sc->udelay; t++) { 356 noack = I2C_GETSDA(dev); 357 if (!noack) 358 break; 359 DELAY(1); 360 } 361 362 DELAY(sc->udelay - t); 363 iicbb_clockout(dev); 364 365 I2C_DEBUG(printf("%c ", noack ? '-' : '+')); 366 return (noack ? IIC_ENOACK : 0); 367 } 368 369 static int 370 iicbb_sendbyte(device_t dev, uint8_t data) 371 { 372 int err, i; 373 374 for (i = 7; i >= 0; i--) { 375 err = iicbb_sendbit(dev, (data & (1 << i)) != 0); 376 if (err != 0) { 377 I2C_DEBUG(printf("w!")); 378 return (err); 379 } 380 } 381 I2C_DEBUG(printf("w%02x", data)); 382 return (0); 383 } 384 385 static int 386 iicbb_readbyte(device_t dev, bool last, uint8_t *data) 387 { 388 struct iicbb_softc *sc = device_get_softc(dev); 389 int i, err; 390 391 /* 392 * Release SDA so that the slave can drive it. 393 * We do not use iicbb_clockin() here because we need to release SDA 394 * only once and then we just pulse the SCL. 395 */ 396 *data = 0; 397 I2C_SETSDA(dev, 1); 398 for (i = 7; i >= 0; i--) { 399 I2C_SETSCL(dev, 1); 400 err = iicbb_waitforscl(dev); 401 if (err != 0) { 402 I2C_DEBUG(printf("r! ")); 403 return (err); 404 } 405 DELAY((sc->udelay + 1) / 2); 406 if (I2C_GETSDA(dev)) 407 *data |= 1 << i; 408 DELAY((sc->udelay + 1) / 2); 409 iicbb_clockout(dev); 410 } 411 412 /* 413 * Send master->slave ACK (low) for more data, 414 * NoACK (high) otherwise. 415 */ 416 iicbb_sendbit(dev, last); 417 I2C_DEBUG(printf("r%02x%c ", *data, last ? '-' : '+')); 418 return (0); 419 } 420 421 static int 422 iicbb_callback(device_t dev, int index, caddr_t data) 423 { 424 return (IICBB_CALLBACK(device_get_parent(dev), index, data)); 425 } 426 427 static int 428 iicbb_reset(device_t dev, u_char speed, u_char addr, u_char *oldaddr) 429 { 430 iicbb_set_speed(device_get_softc(dev), speed); 431 return (IICBB_RESET(device_get_parent(dev), speed, addr, oldaddr)); 432 } 433 434 static int 435 iicbb_start_impl(device_t dev, u_char slave, bool repstart) 436 { 437 struct iicbb_softc *sc = device_get_softc(dev); 438 int error; 439 440 if (!repstart) { 441 I2C_DEBUG(printf("<<")); 442 443 /* SCL must be high on the idle bus. */ 444 if (iicbb_waitforscl(dev) != 0) { 445 I2C_DEBUG(printf("C!\n")); 446 return (IIC_EBUSERR); 447 } 448 } else { 449 I2C_DEBUG(printf("<")); 450 error = iicbb_clockin(dev, 1); 451 if (error != 0) 452 return (error); 453 454 /* SDA will go low in the middle of the SCL high phase. */ 455 DELAY((sc->udelay + 1) / 2); 456 } 457 458 /* 459 * SDA must be high after the earlier stop condition or the end 460 * of Ack/NoAck pulse. 461 */ 462 if (!I2C_GETSDA(dev)) { 463 I2C_DEBUG(printf("D!\n")); 464 return (IIC_EBUSERR); 465 } 466 467 /* Start: SDA high->low. */ 468 I2C_SETSDA(dev, 0); 469 470 /* Wait the second half of the SCL high phase. */ 471 DELAY((sc->udelay + 1) / 2); 472 473 /* Pull SCL low to keep the bus reserved. */ 474 iicbb_clockout(dev); 475 476 /* send address */ 477 error = iicbb_sendbyte(dev, slave); 478 479 /* check for ack */ 480 if (error == 0) 481 error = iicbb_getack(dev); 482 if (error != 0) 483 (void)iicbb_stop(dev); 484 return (error); 485 } 486 487 /* NB: the timeout is ignored. */ 488 static int 489 iicbb_start(device_t dev, u_char slave, int timeout) 490 { 491 return (iicbb_start_impl(dev, slave, false)); 492 } 493 494 /* NB: the timeout is ignored. */ 495 static int 496 iicbb_repstart(device_t dev, u_char slave, int timeout) 497 { 498 return (iicbb_start_impl(dev, slave, true)); 499 } 500 501 static int 502 iicbb_stop(device_t dev) 503 { 504 struct iicbb_softc *sc = device_get_softc(dev); 505 int err = 0; 506 507 /* 508 * Stop: SDA goes from low to high in the middle of the SCL high phase. 509 */ 510 err = iicbb_clockin(dev, 0); 511 if (err != 0) 512 return (err); 513 DELAY((sc->udelay + 1) / 2); 514 I2C_SETSDA(dev, 1); 515 DELAY((sc->udelay + 1) / 2); 516 517 I2C_DEBUG(printf("%s>>", err != 0 ? "!" : "")); 518 I2C_DEBUG(printf("\n")); 519 return (err); 520 } 521 522 /* NB: the timeout is ignored. */ 523 static int 524 iicbb_write(device_t dev, const char *buf, int len, int *sent, int timeout) 525 { 526 int bytes, error = 0; 527 528 bytes = 0; 529 while (len > 0) { 530 /* send byte */ 531 iicbb_sendbyte(dev, (uint8_t)*buf++); 532 533 /* check for ack */ 534 error = iicbb_getack(dev); 535 if (error != 0) 536 break; 537 bytes++; 538 len--; 539 } 540 541 *sent = bytes; 542 return (error); 543 } 544 545 /* NB: whatever delay is, it's ignored. */ 546 static int 547 iicbb_read(device_t dev, char *buf, int len, int *read, int last, int delay) 548 { 549 int bytes = 0; 550 int err = 0; 551 552 while (len > 0) { 553 err = iicbb_readbyte(dev, (len == 1) ? last : 0, 554 (uint8_t *)buf); 555 if (err != 0) 556 break; 557 buf++; 558 bytes++; 559 len--; 560 } 561 562 *read = bytes; 563 return (err); 564 } 565 566 static int 567 iicbb_transfer(device_t dev, struct iic_msg *msgs, uint32_t nmsgs) 568 { 569 int error; 570 571 error = IICBB_PRE_XFER(device_get_parent(dev)); 572 if (error) 573 return (error); 574 575 error = iicbus_transfer_gen(dev, msgs, nmsgs); 576 577 IICBB_POST_XFER(device_get_parent(dev)); 578 return (error); 579 } 580 581 static void 582 iicbb_set_speed(struct iicbb_softc *sc, u_char speed) 583 { 584 u_int busfreq; 585 int period; 586 587 /* 588 * udelay is half a period, the clock is held high or low for this long. 589 */ 590 busfreq = IICBUS_GET_FREQUENCY(sc->iicbus, speed); 591 period = 1000000 / 2 / busfreq; /* Hz -> uS */ 592 period -= sc->io_latency; 593 sc->udelay = MAX(period, 1); 594 } 595 596 DRIVER_MODULE(iicbus, iicbb, iicbus_driver, 0, 0); 597 598 MODULE_DEPEND(iicbb, iicbus, IICBUS_MINVER, IICBUS_PREFVER, IICBUS_MAXVER); 599 MODULE_VERSION(iicbb, IICBB_MODVER); 600