1 /****************************************************************************** 2 3 Copyright (c) 2001-2014, Intel Corporation 4 All rights reserved. 5 6 Redistribution and use in source and binary forms, with or without 7 modification, are permitted provided that the following conditions are met: 8 9 1. Redistributions of source code must retain the above copyright notice, 10 this list of conditions and the following disclaimer. 11 12 2. Redistributions in binary form must reproduce the above copyright 13 notice, this list of conditions and the following disclaimer in the 14 documentation and/or other materials provided with the distribution. 15 16 3. Neither the name of the Intel Corporation nor the names of its 17 contributors may be used to endorse or promote products derived from 18 this software without specific prior written permission. 19 20 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 21 AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE 24 LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 30 POSSIBILITY OF SUCH DAMAGE. 31 32 ******************************************************************************/ 33 /*$FreeBSD$*/ 34 35 /* 36 * 82575EB Gigabit Network Connection 37 * 82575EB Gigabit Backplane Connection 38 * 82575GB Gigabit Network Connection 39 * 82576 Gigabit Network Connection 40 * 82576 Quad Port Gigabit Mezzanine Adapter 41 * 82580 Gigabit Network Connection 42 * I350 Gigabit Network Connection 43 */ 44 45 #include "e1000_api.h" 46 #include "e1000_i210.h" 47 48 static s32 e1000_init_phy_params_82575(struct e1000_hw *hw); 49 static s32 e1000_init_mac_params_82575(struct e1000_hw *hw); 50 static s32 e1000_acquire_phy_82575(struct e1000_hw *hw); 51 static void e1000_release_phy_82575(struct e1000_hw *hw); 52 static s32 e1000_acquire_nvm_82575(struct e1000_hw *hw); 53 static void e1000_release_nvm_82575(struct e1000_hw *hw); 54 static s32 e1000_check_for_link_82575(struct e1000_hw *hw); 55 static s32 e1000_check_for_link_media_swap(struct e1000_hw *hw); 56 static s32 e1000_get_cfg_done_82575(struct e1000_hw *hw); 57 static s32 e1000_get_link_up_info_82575(struct e1000_hw *hw, u16 *speed, 58 u16 *duplex); 59 static s32 e1000_phy_hw_reset_sgmii_82575(struct e1000_hw *hw); 60 static s32 e1000_read_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset, 61 u16 *data); 62 static s32 e1000_reset_hw_82575(struct e1000_hw *hw); 63 static s32 e1000_reset_hw_82580(struct e1000_hw *hw); 64 static s32 e1000_read_phy_reg_82580(struct e1000_hw *hw, 65 u32 offset, u16 *data); 66 static s32 e1000_write_phy_reg_82580(struct e1000_hw *hw, 67 u32 offset, u16 data); 68 static s32 e1000_set_d0_lplu_state_82580(struct e1000_hw *hw, 69 bool active); 70 static s32 e1000_set_d3_lplu_state_82580(struct e1000_hw *hw, 71 bool active); 72 static s32 e1000_set_d0_lplu_state_82575(struct e1000_hw *hw, 73 bool active); 74 static s32 e1000_setup_copper_link_82575(struct e1000_hw *hw); 75 static s32 e1000_setup_serdes_link_82575(struct e1000_hw *hw); 76 static s32 e1000_get_media_type_82575(struct e1000_hw *hw); 77 static s32 e1000_set_sfp_media_type_82575(struct e1000_hw *hw); 78 static s32 e1000_valid_led_default_82575(struct e1000_hw *hw, u16 *data); 79 static s32 e1000_write_phy_reg_sgmii_82575(struct e1000_hw *hw, 80 u32 offset, u16 data); 81 static void e1000_clear_hw_cntrs_82575(struct e1000_hw *hw); 82 static s32 e1000_acquire_swfw_sync_82575(struct e1000_hw *hw, u16 mask); 83 static s32 e1000_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw, 84 u16 *speed, u16 *duplex); 85 static s32 e1000_get_phy_id_82575(struct e1000_hw *hw); 86 static void e1000_release_swfw_sync_82575(struct e1000_hw *hw, u16 mask); 87 static bool e1000_sgmii_active_82575(struct e1000_hw *hw); 88 static s32 e1000_reset_init_script_82575(struct e1000_hw *hw); 89 static s32 e1000_read_mac_addr_82575(struct e1000_hw *hw); 90 static void e1000_config_collision_dist_82575(struct e1000_hw *hw); 91 static void e1000_power_down_phy_copper_82575(struct e1000_hw *hw); 92 static void e1000_shutdown_serdes_link_82575(struct e1000_hw *hw); 93 static void e1000_power_up_serdes_link_82575(struct e1000_hw *hw); 94 static s32 e1000_set_pcie_completion_timeout(struct e1000_hw *hw); 95 static s32 e1000_reset_mdicnfg_82580(struct e1000_hw *hw); 96 static s32 e1000_validate_nvm_checksum_82580(struct e1000_hw *hw); 97 static s32 e1000_update_nvm_checksum_82580(struct e1000_hw *hw); 98 static s32 e1000_update_nvm_checksum_with_offset(struct e1000_hw *hw, 99 u16 offset); 100 static s32 e1000_validate_nvm_checksum_with_offset(struct e1000_hw *hw, 101 u16 offset); 102 static s32 e1000_validate_nvm_checksum_i350(struct e1000_hw *hw); 103 static s32 e1000_update_nvm_checksum_i350(struct e1000_hw *hw); 104 static void e1000_write_vfta_i350(struct e1000_hw *hw, u32 offset, u32 value); 105 static void e1000_clear_vfta_i350(struct e1000_hw *hw); 106 107 static void e1000_i2c_start(struct e1000_hw *hw); 108 static void e1000_i2c_stop(struct e1000_hw *hw); 109 static s32 e1000_clock_in_i2c_byte(struct e1000_hw *hw, u8 *data); 110 static s32 e1000_clock_out_i2c_byte(struct e1000_hw *hw, u8 data); 111 static s32 e1000_get_i2c_ack(struct e1000_hw *hw); 112 static s32 e1000_clock_in_i2c_bit(struct e1000_hw *hw, bool *data); 113 static s32 e1000_clock_out_i2c_bit(struct e1000_hw *hw, bool data); 114 static void e1000_raise_i2c_clk(struct e1000_hw *hw, u32 *i2cctl); 115 static void e1000_lower_i2c_clk(struct e1000_hw *hw, u32 *i2cctl); 116 static s32 e1000_set_i2c_data(struct e1000_hw *hw, u32 *i2cctl, bool data); 117 static bool e1000_get_i2c_data(u32 *i2cctl); 118 119 static const u16 e1000_82580_rxpbs_table[] = { 120 36, 72, 144, 1, 2, 4, 8, 16, 35, 70, 140 }; 121 #define E1000_82580_RXPBS_TABLE_SIZE \ 122 (sizeof(e1000_82580_rxpbs_table) / \ 123 sizeof(e1000_82580_rxpbs_table[0])) 124 125 126 /** 127 * e1000_sgmii_uses_mdio_82575 - Determine if I2C pins are for external MDIO 128 * @hw: pointer to the HW structure 129 * 130 * Called to determine if the I2C pins are being used for I2C or as an 131 * external MDIO interface since the two options are mutually exclusive. 132 **/ 133 static bool e1000_sgmii_uses_mdio_82575(struct e1000_hw *hw) 134 { 135 u32 reg = 0; 136 bool ext_mdio = FALSE; 137 138 DEBUGFUNC("e1000_sgmii_uses_mdio_82575"); 139 140 switch (hw->mac.type) { 141 case e1000_82575: 142 case e1000_82576: 143 reg = E1000_READ_REG(hw, E1000_MDIC); 144 ext_mdio = !!(reg & E1000_MDIC_DEST); 145 break; 146 case e1000_82580: 147 case e1000_i350: 148 case e1000_i354: 149 case e1000_i210: 150 case e1000_i211: 151 reg = E1000_READ_REG(hw, E1000_MDICNFG); 152 ext_mdio = !!(reg & E1000_MDICNFG_EXT_MDIO); 153 break; 154 default: 155 break; 156 } 157 return ext_mdio; 158 } 159 160 /** 161 * e1000_init_phy_params_82575 - Init PHY func ptrs. 162 * @hw: pointer to the HW structure 163 **/ 164 static s32 e1000_init_phy_params_82575(struct e1000_hw *hw) 165 { 166 struct e1000_phy_info *phy = &hw->phy; 167 s32 ret_val = E1000_SUCCESS; 168 u32 ctrl_ext; 169 170 DEBUGFUNC("e1000_init_phy_params_82575"); 171 172 phy->ops.read_i2c_byte = e1000_read_i2c_byte_generic; 173 phy->ops.write_i2c_byte = e1000_write_i2c_byte_generic; 174 175 if (hw->phy.media_type != e1000_media_type_copper) { 176 phy->type = e1000_phy_none; 177 goto out; 178 } 179 180 phy->ops.power_up = e1000_power_up_phy_copper; 181 phy->ops.power_down = e1000_power_down_phy_copper_82575; 182 183 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; 184 phy->reset_delay_us = 100; 185 186 phy->ops.acquire = e1000_acquire_phy_82575; 187 phy->ops.check_reset_block = e1000_check_reset_block_generic; 188 phy->ops.commit = e1000_phy_sw_reset_generic; 189 phy->ops.get_cfg_done = e1000_get_cfg_done_82575; 190 phy->ops.release = e1000_release_phy_82575; 191 192 ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); 193 194 if (e1000_sgmii_active_82575(hw)) { 195 phy->ops.reset = e1000_phy_hw_reset_sgmii_82575; 196 ctrl_ext |= E1000_CTRL_I2C_ENA; 197 } else { 198 phy->ops.reset = e1000_phy_hw_reset_generic; 199 ctrl_ext &= ~E1000_CTRL_I2C_ENA; 200 } 201 202 E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); 203 e1000_reset_mdicnfg_82580(hw); 204 205 if (e1000_sgmii_active_82575(hw) && !e1000_sgmii_uses_mdio_82575(hw)) { 206 phy->ops.read_reg = e1000_read_phy_reg_sgmii_82575; 207 phy->ops.write_reg = e1000_write_phy_reg_sgmii_82575; 208 } else { 209 switch (hw->mac.type) { 210 case e1000_82580: 211 case e1000_i350: 212 case e1000_i354: 213 phy->ops.read_reg = e1000_read_phy_reg_82580; 214 phy->ops.write_reg = e1000_write_phy_reg_82580; 215 break; 216 case e1000_i210: 217 case e1000_i211: 218 phy->ops.read_reg = e1000_read_phy_reg_gs40g; 219 phy->ops.write_reg = e1000_write_phy_reg_gs40g; 220 break; 221 default: 222 phy->ops.read_reg = e1000_read_phy_reg_igp; 223 phy->ops.write_reg = e1000_write_phy_reg_igp; 224 } 225 } 226 227 /* Set phy->phy_addr and phy->id. */ 228 ret_val = e1000_get_phy_id_82575(hw); 229 230 /* Verify phy id and set remaining function pointers */ 231 switch (phy->id) { 232 case M88E1543_E_PHY_ID: 233 case M88E1512_E_PHY_ID: 234 case I347AT4_E_PHY_ID: 235 case M88E1112_E_PHY_ID: 236 case M88E1340M_E_PHY_ID: 237 case M88E1111_I_PHY_ID: 238 phy->type = e1000_phy_m88; 239 phy->ops.check_polarity = e1000_check_polarity_m88; 240 phy->ops.get_info = e1000_get_phy_info_m88; 241 if (phy->id == I347AT4_E_PHY_ID || 242 phy->id == M88E1112_E_PHY_ID || 243 phy->id == M88E1340M_E_PHY_ID) 244 phy->ops.get_cable_length = 245 e1000_get_cable_length_m88_gen2; 246 else if (phy->id == M88E1543_E_PHY_ID || 247 phy->id == M88E1512_E_PHY_ID) 248 phy->ops.get_cable_length = 249 e1000_get_cable_length_m88_gen2; 250 else 251 phy->ops.get_cable_length = e1000_get_cable_length_m88; 252 phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_m88; 253 /* Check if this PHY is confgured for media swap. */ 254 if (phy->id == M88E1112_E_PHY_ID) { 255 u16 data; 256 257 ret_val = phy->ops.write_reg(hw, 258 E1000_M88E1112_PAGE_ADDR, 259 2); 260 if (ret_val) 261 goto out; 262 263 ret_val = phy->ops.read_reg(hw, 264 E1000_M88E1112_MAC_CTRL_1, 265 &data); 266 if (ret_val) 267 goto out; 268 269 data = (data & E1000_M88E1112_MAC_CTRL_1_MODE_MASK) >> 270 E1000_M88E1112_MAC_CTRL_1_MODE_SHIFT; 271 if (data == E1000_M88E1112_AUTO_COPPER_SGMII || 272 data == E1000_M88E1112_AUTO_COPPER_BASEX) 273 hw->mac.ops.check_for_link = 274 e1000_check_for_link_media_swap; 275 } 276 if (phy->id == M88E1512_E_PHY_ID) { 277 ret_val = e1000_initialize_M88E1512_phy(hw); 278 if (ret_val) 279 goto out; 280 } 281 break; 282 case IGP03E1000_E_PHY_ID: 283 case IGP04E1000_E_PHY_ID: 284 phy->type = e1000_phy_igp_3; 285 phy->ops.check_polarity = e1000_check_polarity_igp; 286 phy->ops.get_info = e1000_get_phy_info_igp; 287 phy->ops.get_cable_length = e1000_get_cable_length_igp_2; 288 phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_igp; 289 phy->ops.set_d0_lplu_state = e1000_set_d0_lplu_state_82575; 290 phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_generic; 291 break; 292 case I82580_I_PHY_ID: 293 case I350_I_PHY_ID: 294 phy->type = e1000_phy_82580; 295 phy->ops.check_polarity = e1000_check_polarity_82577; 296 phy->ops.force_speed_duplex = 297 e1000_phy_force_speed_duplex_82577; 298 phy->ops.get_cable_length = e1000_get_cable_length_82577; 299 phy->ops.get_info = e1000_get_phy_info_82577; 300 phy->ops.set_d0_lplu_state = e1000_set_d0_lplu_state_82580; 301 phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_82580; 302 break; 303 case I210_I_PHY_ID: 304 phy->type = e1000_phy_i210; 305 phy->ops.check_polarity = e1000_check_polarity_m88; 306 phy->ops.get_info = e1000_get_phy_info_m88; 307 phy->ops.get_cable_length = e1000_get_cable_length_m88_gen2; 308 phy->ops.set_d0_lplu_state = e1000_set_d0_lplu_state_82580; 309 phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_82580; 310 phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_m88; 311 break; 312 default: 313 ret_val = -E1000_ERR_PHY; 314 goto out; 315 } 316 317 out: 318 return ret_val; 319 } 320 321 /** 322 * e1000_init_nvm_params_82575 - Init NVM func ptrs. 323 * @hw: pointer to the HW structure 324 **/ 325 s32 e1000_init_nvm_params_82575(struct e1000_hw *hw) 326 { 327 struct e1000_nvm_info *nvm = &hw->nvm; 328 u32 eecd = E1000_READ_REG(hw, E1000_EECD); 329 u16 size; 330 331 DEBUGFUNC("e1000_init_nvm_params_82575"); 332 333 size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >> 334 E1000_EECD_SIZE_EX_SHIFT); 335 /* 336 * Added to a constant, "size" becomes the left-shift value 337 * for setting word_size. 338 */ 339 size += NVM_WORD_SIZE_BASE_SHIFT; 340 341 /* Just in case size is out of range, cap it to the largest 342 * EEPROM size supported 343 */ 344 if (size > 15) 345 size = 15; 346 347 nvm->word_size = 1 << size; 348 if (hw->mac.type < e1000_i210) { 349 nvm->opcode_bits = 8; 350 nvm->delay_usec = 1; 351 352 switch (nvm->override) { 353 case e1000_nvm_override_spi_large: 354 nvm->page_size = 32; 355 nvm->address_bits = 16; 356 break; 357 case e1000_nvm_override_spi_small: 358 nvm->page_size = 8; 359 nvm->address_bits = 8; 360 break; 361 default: 362 nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8; 363 nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 364 16 : 8; 365 break; 366 } 367 if (nvm->word_size == (1 << 15)) 368 nvm->page_size = 128; 369 370 nvm->type = e1000_nvm_eeprom_spi; 371 } else { 372 nvm->type = e1000_nvm_flash_hw; 373 } 374 375 /* Function Pointers */ 376 nvm->ops.acquire = e1000_acquire_nvm_82575; 377 nvm->ops.release = e1000_release_nvm_82575; 378 if (nvm->word_size < (1 << 15)) 379 nvm->ops.read = e1000_read_nvm_eerd; 380 else 381 nvm->ops.read = e1000_read_nvm_spi; 382 383 nvm->ops.write = e1000_write_nvm_spi; 384 nvm->ops.validate = e1000_validate_nvm_checksum_generic; 385 nvm->ops.update = e1000_update_nvm_checksum_generic; 386 nvm->ops.valid_led_default = e1000_valid_led_default_82575; 387 388 /* override generic family function pointers for specific descendants */ 389 switch (hw->mac.type) { 390 case e1000_82580: 391 nvm->ops.validate = e1000_validate_nvm_checksum_82580; 392 nvm->ops.update = e1000_update_nvm_checksum_82580; 393 break; 394 case e1000_i350: 395 case e1000_i354: 396 nvm->ops.validate = e1000_validate_nvm_checksum_i350; 397 nvm->ops.update = e1000_update_nvm_checksum_i350; 398 break; 399 default: 400 break; 401 } 402 403 return E1000_SUCCESS; 404 } 405 406 /** 407 * e1000_init_mac_params_82575 - Init MAC func ptrs. 408 * @hw: pointer to the HW structure 409 **/ 410 static s32 e1000_init_mac_params_82575(struct e1000_hw *hw) 411 { 412 struct e1000_mac_info *mac = &hw->mac; 413 struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575; 414 415 DEBUGFUNC("e1000_init_mac_params_82575"); 416 417 /* Derives media type */ 418 e1000_get_media_type_82575(hw); 419 /* Set mta register count */ 420 mac->mta_reg_count = 128; 421 /* Set uta register count */ 422 mac->uta_reg_count = (hw->mac.type == e1000_82575) ? 0 : 128; 423 /* Set rar entry count */ 424 mac->rar_entry_count = E1000_RAR_ENTRIES_82575; 425 if (mac->type == e1000_82576) 426 mac->rar_entry_count = E1000_RAR_ENTRIES_82576; 427 if (mac->type == e1000_82580) 428 mac->rar_entry_count = E1000_RAR_ENTRIES_82580; 429 if (mac->type == e1000_i350 || mac->type == e1000_i354) 430 mac->rar_entry_count = E1000_RAR_ENTRIES_I350; 431 432 /* Enable EEE default settings for EEE supported devices */ 433 if (mac->type >= e1000_i350) 434 dev_spec->eee_disable = FALSE; 435 436 /* Allow a single clear of the SW semaphore on I210 and newer */ 437 if (mac->type >= e1000_i210) 438 dev_spec->clear_semaphore_once = TRUE; 439 440 /* Set if part includes ASF firmware */ 441 mac->asf_firmware_present = TRUE; 442 /* FWSM register */ 443 mac->has_fwsm = TRUE; 444 /* ARC supported; valid only if manageability features are enabled. */ 445 mac->arc_subsystem_valid = 446 !!(E1000_READ_REG(hw, E1000_FWSM) & E1000_FWSM_MODE_MASK); 447 448 /* Function pointers */ 449 450 /* bus type/speed/width */ 451 mac->ops.get_bus_info = e1000_get_bus_info_pcie_generic; 452 /* reset */ 453 if (mac->type >= e1000_82580) 454 mac->ops.reset_hw = e1000_reset_hw_82580; 455 else 456 mac->ops.reset_hw = e1000_reset_hw_82575; 457 /* hw initialization */ 458 if ((mac->type == e1000_i210) || (mac->type == e1000_i211)) 459 mac->ops.init_hw = e1000_init_hw_i210; 460 else 461 mac->ops.init_hw = e1000_init_hw_82575; 462 /* link setup */ 463 mac->ops.setup_link = e1000_setup_link_generic; 464 /* physical interface link setup */ 465 mac->ops.setup_physical_interface = 466 (hw->phy.media_type == e1000_media_type_copper) 467 ? e1000_setup_copper_link_82575 : e1000_setup_serdes_link_82575; 468 /* physical interface shutdown */ 469 mac->ops.shutdown_serdes = e1000_shutdown_serdes_link_82575; 470 /* physical interface power up */ 471 mac->ops.power_up_serdes = e1000_power_up_serdes_link_82575; 472 /* check for link */ 473 mac->ops.check_for_link = e1000_check_for_link_82575; 474 /* read mac address */ 475 mac->ops.read_mac_addr = e1000_read_mac_addr_82575; 476 /* configure collision distance */ 477 mac->ops.config_collision_dist = e1000_config_collision_dist_82575; 478 /* multicast address update */ 479 mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic; 480 if (hw->mac.type == e1000_i350 || mac->type == e1000_i354) { 481 /* writing VFTA */ 482 mac->ops.write_vfta = e1000_write_vfta_i350; 483 /* clearing VFTA */ 484 mac->ops.clear_vfta = e1000_clear_vfta_i350; 485 } else { 486 /* writing VFTA */ 487 mac->ops.write_vfta = e1000_write_vfta_generic; 488 /* clearing VFTA */ 489 mac->ops.clear_vfta = e1000_clear_vfta_generic; 490 } 491 if (hw->mac.type >= e1000_82580) 492 mac->ops.validate_mdi_setting = 493 e1000_validate_mdi_setting_crossover_generic; 494 /* ID LED init */ 495 mac->ops.id_led_init = e1000_id_led_init_generic; 496 /* blink LED */ 497 mac->ops.blink_led = e1000_blink_led_generic; 498 /* setup LED */ 499 mac->ops.setup_led = e1000_setup_led_generic; 500 /* cleanup LED */ 501 mac->ops.cleanup_led = e1000_cleanup_led_generic; 502 /* turn on/off LED */ 503 mac->ops.led_on = e1000_led_on_generic; 504 mac->ops.led_off = e1000_led_off_generic; 505 /* clear hardware counters */ 506 mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_82575; 507 /* link info */ 508 mac->ops.get_link_up_info = e1000_get_link_up_info_82575; 509 /* acquire SW_FW sync */ 510 mac->ops.acquire_swfw_sync = e1000_acquire_swfw_sync_82575; 511 mac->ops.release_swfw_sync = e1000_release_swfw_sync_82575; 512 if (mac->type >= e1000_i210) { 513 mac->ops.acquire_swfw_sync = e1000_acquire_swfw_sync_i210; 514 mac->ops.release_swfw_sync = e1000_release_swfw_sync_i210; 515 } 516 517 /* set lan id for port to determine which phy lock to use */ 518 hw->mac.ops.set_lan_id(hw); 519 520 return E1000_SUCCESS; 521 } 522 523 /** 524 * e1000_init_function_pointers_82575 - Init func ptrs. 525 * @hw: pointer to the HW structure 526 * 527 * Called to initialize all function pointers and parameters. 528 **/ 529 void e1000_init_function_pointers_82575(struct e1000_hw *hw) 530 { 531 DEBUGFUNC("e1000_init_function_pointers_82575"); 532 533 hw->mac.ops.init_params = e1000_init_mac_params_82575; 534 hw->nvm.ops.init_params = e1000_init_nvm_params_82575; 535 hw->phy.ops.init_params = e1000_init_phy_params_82575; 536 hw->mbx.ops.init_params = e1000_init_mbx_params_pf; 537 } 538 539 /** 540 * e1000_acquire_phy_82575 - Acquire rights to access PHY 541 * @hw: pointer to the HW structure 542 * 543 * Acquire access rights to the correct PHY. 544 **/ 545 static s32 e1000_acquire_phy_82575(struct e1000_hw *hw) 546 { 547 u16 mask = E1000_SWFW_PHY0_SM; 548 549 DEBUGFUNC("e1000_acquire_phy_82575"); 550 551 if (hw->bus.func == E1000_FUNC_1) 552 mask = E1000_SWFW_PHY1_SM; 553 else if (hw->bus.func == E1000_FUNC_2) 554 mask = E1000_SWFW_PHY2_SM; 555 else if (hw->bus.func == E1000_FUNC_3) 556 mask = E1000_SWFW_PHY3_SM; 557 558 return hw->mac.ops.acquire_swfw_sync(hw, mask); 559 } 560 561 /** 562 * e1000_release_phy_82575 - Release rights to access PHY 563 * @hw: pointer to the HW structure 564 * 565 * A wrapper to release access rights to the correct PHY. 566 **/ 567 static void e1000_release_phy_82575(struct e1000_hw *hw) 568 { 569 u16 mask = E1000_SWFW_PHY0_SM; 570 571 DEBUGFUNC("e1000_release_phy_82575"); 572 573 if (hw->bus.func == E1000_FUNC_1) 574 mask = E1000_SWFW_PHY1_SM; 575 else if (hw->bus.func == E1000_FUNC_2) 576 mask = E1000_SWFW_PHY2_SM; 577 else if (hw->bus.func == E1000_FUNC_3) 578 mask = E1000_SWFW_PHY3_SM; 579 580 hw->mac.ops.release_swfw_sync(hw, mask); 581 } 582 583 /** 584 * e1000_read_phy_reg_sgmii_82575 - Read PHY register using sgmii 585 * @hw: pointer to the HW structure 586 * @offset: register offset to be read 587 * @data: pointer to the read data 588 * 589 * Reads the PHY register at offset using the serial gigabit media independent 590 * interface and stores the retrieved information in data. 591 **/ 592 static s32 e1000_read_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset, 593 u16 *data) 594 { 595 s32 ret_val = -E1000_ERR_PARAM; 596 597 DEBUGFUNC("e1000_read_phy_reg_sgmii_82575"); 598 599 if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) { 600 DEBUGOUT1("PHY Address %u is out of range\n", offset); 601 goto out; 602 } 603 604 ret_val = hw->phy.ops.acquire(hw); 605 if (ret_val) 606 goto out; 607 608 ret_val = e1000_read_phy_reg_i2c(hw, offset, data); 609 610 hw->phy.ops.release(hw); 611 612 out: 613 return ret_val; 614 } 615 616 /** 617 * e1000_write_phy_reg_sgmii_82575 - Write PHY register using sgmii 618 * @hw: pointer to the HW structure 619 * @offset: register offset to write to 620 * @data: data to write at register offset 621 * 622 * Writes the data to PHY register at the offset using the serial gigabit 623 * media independent interface. 624 **/ 625 static s32 e1000_write_phy_reg_sgmii_82575(struct e1000_hw *hw, u32 offset, 626 u16 data) 627 { 628 s32 ret_val = -E1000_ERR_PARAM; 629 630 DEBUGFUNC("e1000_write_phy_reg_sgmii_82575"); 631 632 if (offset > E1000_MAX_SGMII_PHY_REG_ADDR) { 633 DEBUGOUT1("PHY Address %d is out of range\n", offset); 634 goto out; 635 } 636 637 ret_val = hw->phy.ops.acquire(hw); 638 if (ret_val) 639 goto out; 640 641 ret_val = e1000_write_phy_reg_i2c(hw, offset, data); 642 643 hw->phy.ops.release(hw); 644 645 out: 646 return ret_val; 647 } 648 649 /** 650 * e1000_get_phy_id_82575 - Retrieve PHY addr and id 651 * @hw: pointer to the HW structure 652 * 653 * Retrieves the PHY address and ID for both PHY's which do and do not use 654 * sgmi interface. 655 **/ 656 static s32 e1000_get_phy_id_82575(struct e1000_hw *hw) 657 { 658 struct e1000_phy_info *phy = &hw->phy; 659 s32 ret_val = E1000_SUCCESS; 660 u16 phy_id; 661 u32 ctrl_ext; 662 u32 mdic; 663 664 DEBUGFUNC("e1000_get_phy_id_82575"); 665 666 /* some i354 devices need an extra read for phy id */ 667 if (hw->mac.type == e1000_i354) 668 e1000_get_phy_id(hw); 669 670 /* 671 * For SGMII PHYs, we try the list of possible addresses until 672 * we find one that works. For non-SGMII PHYs 673 * (e.g. integrated copper PHYs), an address of 1 should 674 * work. The result of this function should mean phy->phy_addr 675 * and phy->id are set correctly. 676 */ 677 if (!e1000_sgmii_active_82575(hw)) { 678 phy->addr = 1; 679 ret_val = e1000_get_phy_id(hw); 680 goto out; 681 } 682 683 if (e1000_sgmii_uses_mdio_82575(hw)) { 684 switch (hw->mac.type) { 685 case e1000_82575: 686 case e1000_82576: 687 mdic = E1000_READ_REG(hw, E1000_MDIC); 688 mdic &= E1000_MDIC_PHY_MASK; 689 phy->addr = mdic >> E1000_MDIC_PHY_SHIFT; 690 break; 691 case e1000_82580: 692 case e1000_i350: 693 case e1000_i354: 694 case e1000_i210: 695 case e1000_i211: 696 mdic = E1000_READ_REG(hw, E1000_MDICNFG); 697 mdic &= E1000_MDICNFG_PHY_MASK; 698 phy->addr = mdic >> E1000_MDICNFG_PHY_SHIFT; 699 break; 700 default: 701 ret_val = -E1000_ERR_PHY; 702 goto out; 703 break; 704 } 705 ret_val = e1000_get_phy_id(hw); 706 goto out; 707 } 708 709 /* Power on sgmii phy if it is disabled */ 710 ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); 711 E1000_WRITE_REG(hw, E1000_CTRL_EXT, 712 ctrl_ext & ~E1000_CTRL_EXT_SDP3_DATA); 713 E1000_WRITE_FLUSH(hw); 714 msec_delay(300); 715 716 /* 717 * The address field in the I2CCMD register is 3 bits and 0 is invalid. 718 * Therefore, we need to test 1-7 719 */ 720 for (phy->addr = 1; phy->addr < 8; phy->addr++) { 721 ret_val = e1000_read_phy_reg_sgmii_82575(hw, PHY_ID1, &phy_id); 722 if (ret_val == E1000_SUCCESS) { 723 DEBUGOUT2("Vendor ID 0x%08X read at address %u\n", 724 phy_id, phy->addr); 725 /* 726 * At the time of this writing, The M88 part is 727 * the only supported SGMII PHY product. 728 */ 729 if (phy_id == M88_VENDOR) 730 break; 731 } else { 732 DEBUGOUT1("PHY address %u was unreadable\n", 733 phy->addr); 734 } 735 } 736 737 /* A valid PHY type couldn't be found. */ 738 if (phy->addr == 8) { 739 phy->addr = 0; 740 ret_val = -E1000_ERR_PHY; 741 } else { 742 ret_val = e1000_get_phy_id(hw); 743 } 744 745 /* restore previous sfp cage power state */ 746 E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); 747 748 out: 749 return ret_val; 750 } 751 752 /** 753 * e1000_phy_hw_reset_sgmii_82575 - Performs a PHY reset 754 * @hw: pointer to the HW structure 755 * 756 * Resets the PHY using the serial gigabit media independent interface. 757 **/ 758 static s32 e1000_phy_hw_reset_sgmii_82575(struct e1000_hw *hw) 759 { 760 s32 ret_val = E1000_SUCCESS; 761 struct e1000_phy_info *phy = &hw->phy; 762 763 DEBUGFUNC("e1000_phy_hw_reset_sgmii_82575"); 764 765 /* 766 * This isn't a TRUE "hard" reset, but is the only reset 767 * available to us at this time. 768 */ 769 770 DEBUGOUT("Soft resetting SGMII attached PHY...\n"); 771 772 if (!(hw->phy.ops.write_reg)) 773 goto out; 774 775 /* 776 * SFP documentation requires the following to configure the SPF module 777 * to work on SGMII. No further documentation is given. 778 */ 779 ret_val = hw->phy.ops.write_reg(hw, 0x1B, 0x8084); 780 if (ret_val) 781 goto out; 782 783 ret_val = hw->phy.ops.commit(hw); 784 if (ret_val) 785 goto out; 786 787 if (phy->id == M88E1512_E_PHY_ID) 788 ret_val = e1000_initialize_M88E1512_phy(hw); 789 out: 790 return ret_val; 791 } 792 793 /** 794 * e1000_set_d0_lplu_state_82575 - Set Low Power Linkup D0 state 795 * @hw: pointer to the HW structure 796 * @active: TRUE to enable LPLU, FALSE to disable 797 * 798 * Sets the LPLU D0 state according to the active flag. When 799 * activating LPLU this function also disables smart speed 800 * and vice versa. LPLU will not be activated unless the 801 * device autonegotiation advertisement meets standards of 802 * either 10 or 10/100 or 10/100/1000 at all duplexes. 803 * This is a function pointer entry point only called by 804 * PHY setup routines. 805 **/ 806 static s32 e1000_set_d0_lplu_state_82575(struct e1000_hw *hw, bool active) 807 { 808 struct e1000_phy_info *phy = &hw->phy; 809 s32 ret_val = E1000_SUCCESS; 810 u16 data; 811 812 DEBUGFUNC("e1000_set_d0_lplu_state_82575"); 813 814 if (!(hw->phy.ops.read_reg)) 815 goto out; 816 817 ret_val = phy->ops.read_reg(hw, IGP02E1000_PHY_POWER_MGMT, &data); 818 if (ret_val) 819 goto out; 820 821 if (active) { 822 data |= IGP02E1000_PM_D0_LPLU; 823 ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, 824 data); 825 if (ret_val) 826 goto out; 827 828 /* When LPLU is enabled, we should disable SmartSpeed */ 829 ret_val = phy->ops.read_reg(hw, IGP01E1000_PHY_PORT_CONFIG, 830 &data); 831 data &= ~IGP01E1000_PSCFR_SMART_SPEED; 832 ret_val = phy->ops.write_reg(hw, IGP01E1000_PHY_PORT_CONFIG, 833 data); 834 if (ret_val) 835 goto out; 836 } else { 837 data &= ~IGP02E1000_PM_D0_LPLU; 838 ret_val = phy->ops.write_reg(hw, IGP02E1000_PHY_POWER_MGMT, 839 data); 840 /* 841 * LPLU and SmartSpeed are mutually exclusive. LPLU is used 842 * during Dx states where the power conservation is most 843 * important. During driver activity we should enable 844 * SmartSpeed, so performance is maintained. 845 */ 846 if (phy->smart_speed == e1000_smart_speed_on) { 847 ret_val = phy->ops.read_reg(hw, 848 IGP01E1000_PHY_PORT_CONFIG, 849 &data); 850 if (ret_val) 851 goto out; 852 853 data |= IGP01E1000_PSCFR_SMART_SPEED; 854 ret_val = phy->ops.write_reg(hw, 855 IGP01E1000_PHY_PORT_CONFIG, 856 data); 857 if (ret_val) 858 goto out; 859 } else if (phy->smart_speed == e1000_smart_speed_off) { 860 ret_val = phy->ops.read_reg(hw, 861 IGP01E1000_PHY_PORT_CONFIG, 862 &data); 863 if (ret_val) 864 goto out; 865 866 data &= ~IGP01E1000_PSCFR_SMART_SPEED; 867 ret_val = phy->ops.write_reg(hw, 868 IGP01E1000_PHY_PORT_CONFIG, 869 data); 870 if (ret_val) 871 goto out; 872 } 873 } 874 875 out: 876 return ret_val; 877 } 878 879 /** 880 * e1000_set_d0_lplu_state_82580 - Set Low Power Linkup D0 state 881 * @hw: pointer to the HW structure 882 * @active: TRUE to enable LPLU, FALSE to disable 883 * 884 * Sets the LPLU D0 state according to the active flag. When 885 * activating LPLU this function also disables smart speed 886 * and vice versa. LPLU will not be activated unless the 887 * device autonegotiation advertisement meets standards of 888 * either 10 or 10/100 or 10/100/1000 at all duplexes. 889 * This is a function pointer entry point only called by 890 * PHY setup routines. 891 **/ 892 static s32 e1000_set_d0_lplu_state_82580(struct e1000_hw *hw, bool active) 893 { 894 struct e1000_phy_info *phy = &hw->phy; 895 u32 data; 896 897 DEBUGFUNC("e1000_set_d0_lplu_state_82580"); 898 899 data = E1000_READ_REG(hw, E1000_82580_PHY_POWER_MGMT); 900 901 if (active) { 902 data |= E1000_82580_PM_D0_LPLU; 903 904 /* When LPLU is enabled, we should disable SmartSpeed */ 905 data &= ~E1000_82580_PM_SPD; 906 } else { 907 data &= ~E1000_82580_PM_D0_LPLU; 908 909 /* 910 * LPLU and SmartSpeed are mutually exclusive. LPLU is used 911 * during Dx states where the power conservation is most 912 * important. During driver activity we should enable 913 * SmartSpeed, so performance is maintained. 914 */ 915 if (phy->smart_speed == e1000_smart_speed_on) 916 data |= E1000_82580_PM_SPD; 917 else if (phy->smart_speed == e1000_smart_speed_off) 918 data &= ~E1000_82580_PM_SPD; 919 } 920 921 E1000_WRITE_REG(hw, E1000_82580_PHY_POWER_MGMT, data); 922 return E1000_SUCCESS; 923 } 924 925 /** 926 * e1000_set_d3_lplu_state_82580 - Sets low power link up state for D3 927 * @hw: pointer to the HW structure 928 * @active: boolean used to enable/disable lplu 929 * 930 * Success returns 0, Failure returns 1 931 * 932 * The low power link up (lplu) state is set to the power management level D3 933 * and SmartSpeed is disabled when active is TRUE, else clear lplu for D3 934 * and enable Smartspeed. LPLU and Smartspeed are mutually exclusive. LPLU 935 * is used during Dx states where the power conservation is most important. 936 * During driver activity, SmartSpeed should be enabled so performance is 937 * maintained. 938 **/ 939 s32 e1000_set_d3_lplu_state_82580(struct e1000_hw *hw, bool active) 940 { 941 struct e1000_phy_info *phy = &hw->phy; 942 u32 data; 943 944 DEBUGFUNC("e1000_set_d3_lplu_state_82580"); 945 946 data = E1000_READ_REG(hw, E1000_82580_PHY_POWER_MGMT); 947 948 if (!active) { 949 data &= ~E1000_82580_PM_D3_LPLU; 950 /* 951 * LPLU and SmartSpeed are mutually exclusive. LPLU is used 952 * during Dx states where the power conservation is most 953 * important. During driver activity we should enable 954 * SmartSpeed, so performance is maintained. 955 */ 956 if (phy->smart_speed == e1000_smart_speed_on) 957 data |= E1000_82580_PM_SPD; 958 else if (phy->smart_speed == e1000_smart_speed_off) 959 data &= ~E1000_82580_PM_SPD; 960 } else if ((phy->autoneg_advertised == E1000_ALL_SPEED_DUPLEX) || 961 (phy->autoneg_advertised == E1000_ALL_NOT_GIG) || 962 (phy->autoneg_advertised == E1000_ALL_10_SPEED)) { 963 data |= E1000_82580_PM_D3_LPLU; 964 /* When LPLU is enabled, we should disable SmartSpeed */ 965 data &= ~E1000_82580_PM_SPD; 966 } 967 968 E1000_WRITE_REG(hw, E1000_82580_PHY_POWER_MGMT, data); 969 return E1000_SUCCESS; 970 } 971 972 /** 973 * e1000_acquire_nvm_82575 - Request for access to EEPROM 974 * @hw: pointer to the HW structure 975 * 976 * Acquire the necessary semaphores for exclusive access to the EEPROM. 977 * Set the EEPROM access request bit and wait for EEPROM access grant bit. 978 * Return successful if access grant bit set, else clear the request for 979 * EEPROM access and return -E1000_ERR_NVM (-1). 980 **/ 981 static s32 e1000_acquire_nvm_82575(struct e1000_hw *hw) 982 { 983 s32 ret_val = E1000_SUCCESS; 984 985 DEBUGFUNC("e1000_acquire_nvm_82575"); 986 987 ret_val = e1000_acquire_swfw_sync_82575(hw, E1000_SWFW_EEP_SM); 988 if (ret_val) 989 goto out; 990 991 /* 992 * Check if there is some access 993 * error this access may hook on 994 */ 995 if (hw->mac.type == e1000_i350) { 996 u32 eecd = E1000_READ_REG(hw, E1000_EECD); 997 if (eecd & (E1000_EECD_BLOCKED | E1000_EECD_ABORT | 998 E1000_EECD_TIMEOUT)) { 999 /* Clear all access error flags */ 1000 E1000_WRITE_REG(hw, E1000_EECD, eecd | 1001 E1000_EECD_ERROR_CLR); 1002 DEBUGOUT("Nvm bit banging access error detected and cleared.\n"); 1003 } 1004 } 1005 1006 if (hw->mac.type == e1000_82580) { 1007 u32 eecd = E1000_READ_REG(hw, E1000_EECD); 1008 if (eecd & E1000_EECD_BLOCKED) { 1009 /* Clear access error flag */ 1010 E1000_WRITE_REG(hw, E1000_EECD, eecd | 1011 E1000_EECD_BLOCKED); 1012 DEBUGOUT("Nvm bit banging access error detected and cleared.\n"); 1013 } 1014 } 1015 1016 ret_val = e1000_acquire_nvm_generic(hw); 1017 if (ret_val) 1018 e1000_release_swfw_sync_82575(hw, E1000_SWFW_EEP_SM); 1019 1020 out: 1021 return ret_val; 1022 } 1023 1024 /** 1025 * e1000_release_nvm_82575 - Release exclusive access to EEPROM 1026 * @hw: pointer to the HW structure 1027 * 1028 * Stop any current commands to the EEPROM and clear the EEPROM request bit, 1029 * then release the semaphores acquired. 1030 **/ 1031 static void e1000_release_nvm_82575(struct e1000_hw *hw) 1032 { 1033 DEBUGFUNC("e1000_release_nvm_82575"); 1034 1035 e1000_release_nvm_generic(hw); 1036 1037 e1000_release_swfw_sync_82575(hw, E1000_SWFW_EEP_SM); 1038 } 1039 1040 /** 1041 * e1000_acquire_swfw_sync_82575 - Acquire SW/FW semaphore 1042 * @hw: pointer to the HW structure 1043 * @mask: specifies which semaphore to acquire 1044 * 1045 * Acquire the SW/FW semaphore to access the PHY or NVM. The mask 1046 * will also specify which port we're acquiring the lock for. 1047 **/ 1048 static s32 e1000_acquire_swfw_sync_82575(struct e1000_hw *hw, u16 mask) 1049 { 1050 u32 swfw_sync; 1051 u32 swmask = mask; 1052 u32 fwmask = mask << 16; 1053 s32 ret_val = E1000_SUCCESS; 1054 s32 i = 0, timeout = 200; /* FIXME: find real value to use here */ 1055 1056 DEBUGFUNC("e1000_acquire_swfw_sync_82575"); 1057 1058 while (i < timeout) { 1059 if (e1000_get_hw_semaphore_generic(hw)) { 1060 ret_val = -E1000_ERR_SWFW_SYNC; 1061 goto out; 1062 } 1063 1064 swfw_sync = E1000_READ_REG(hw, E1000_SW_FW_SYNC); 1065 if (!(swfw_sync & (fwmask | swmask))) 1066 break; 1067 1068 /* 1069 * Firmware currently using resource (fwmask) 1070 * or other software thread using resource (swmask) 1071 */ 1072 e1000_put_hw_semaphore_generic(hw); 1073 msec_delay_irq(5); 1074 i++; 1075 } 1076 1077 if (i == timeout) { 1078 DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n"); 1079 ret_val = -E1000_ERR_SWFW_SYNC; 1080 goto out; 1081 } 1082 1083 swfw_sync |= swmask; 1084 E1000_WRITE_REG(hw, E1000_SW_FW_SYNC, swfw_sync); 1085 1086 e1000_put_hw_semaphore_generic(hw); 1087 1088 out: 1089 return ret_val; 1090 } 1091 1092 /** 1093 * e1000_release_swfw_sync_82575 - Release SW/FW semaphore 1094 * @hw: pointer to the HW structure 1095 * @mask: specifies which semaphore to acquire 1096 * 1097 * Release the SW/FW semaphore used to access the PHY or NVM. The mask 1098 * will also specify which port we're releasing the lock for. 1099 **/ 1100 static void e1000_release_swfw_sync_82575(struct e1000_hw *hw, u16 mask) 1101 { 1102 u32 swfw_sync; 1103 1104 DEBUGFUNC("e1000_release_swfw_sync_82575"); 1105 1106 while (e1000_get_hw_semaphore_generic(hw) != E1000_SUCCESS) 1107 ; /* Empty */ 1108 1109 swfw_sync = E1000_READ_REG(hw, E1000_SW_FW_SYNC); 1110 swfw_sync &= ~mask; 1111 E1000_WRITE_REG(hw, E1000_SW_FW_SYNC, swfw_sync); 1112 1113 e1000_put_hw_semaphore_generic(hw); 1114 } 1115 1116 /** 1117 * e1000_get_cfg_done_82575 - Read config done bit 1118 * @hw: pointer to the HW structure 1119 * 1120 * Read the management control register for the config done bit for 1121 * completion status. NOTE: silicon which is EEPROM-less will fail trying 1122 * to read the config done bit, so an error is *ONLY* logged and returns 1123 * E1000_SUCCESS. If we were to return with error, EEPROM-less silicon 1124 * would not be able to be reset or change link. 1125 **/ 1126 static s32 e1000_get_cfg_done_82575(struct e1000_hw *hw) 1127 { 1128 s32 timeout = PHY_CFG_TIMEOUT; 1129 u32 mask = E1000_NVM_CFG_DONE_PORT_0; 1130 1131 DEBUGFUNC("e1000_get_cfg_done_82575"); 1132 1133 if (hw->bus.func == E1000_FUNC_1) 1134 mask = E1000_NVM_CFG_DONE_PORT_1; 1135 else if (hw->bus.func == E1000_FUNC_2) 1136 mask = E1000_NVM_CFG_DONE_PORT_2; 1137 else if (hw->bus.func == E1000_FUNC_3) 1138 mask = E1000_NVM_CFG_DONE_PORT_3; 1139 while (timeout) { 1140 if (E1000_READ_REG(hw, E1000_EEMNGCTL) & mask) 1141 break; 1142 msec_delay(1); 1143 timeout--; 1144 } 1145 if (!timeout) 1146 DEBUGOUT("MNG configuration cycle has not completed.\n"); 1147 1148 /* If EEPROM is not marked present, init the PHY manually */ 1149 if (!(E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_PRES) && 1150 (hw->phy.type == e1000_phy_igp_3)) 1151 e1000_phy_init_script_igp3(hw); 1152 1153 return E1000_SUCCESS; 1154 } 1155 1156 /** 1157 * e1000_get_link_up_info_82575 - Get link speed/duplex info 1158 * @hw: pointer to the HW structure 1159 * @speed: stores the current speed 1160 * @duplex: stores the current duplex 1161 * 1162 * This is a wrapper function, if using the serial gigabit media independent 1163 * interface, use PCS to retrieve the link speed and duplex information. 1164 * Otherwise, use the generic function to get the link speed and duplex info. 1165 **/ 1166 static s32 e1000_get_link_up_info_82575(struct e1000_hw *hw, u16 *speed, 1167 u16 *duplex) 1168 { 1169 s32 ret_val; 1170 1171 DEBUGFUNC("e1000_get_link_up_info_82575"); 1172 1173 if (hw->phy.media_type != e1000_media_type_copper) 1174 ret_val = e1000_get_pcs_speed_and_duplex_82575(hw, speed, 1175 duplex); 1176 else 1177 ret_val = e1000_get_speed_and_duplex_copper_generic(hw, speed, 1178 duplex); 1179 1180 return ret_val; 1181 } 1182 1183 /** 1184 * e1000_check_for_link_82575 - Check for link 1185 * @hw: pointer to the HW structure 1186 * 1187 * If sgmii is enabled, then use the pcs register to determine link, otherwise 1188 * use the generic interface for determining link. 1189 **/ 1190 static s32 e1000_check_for_link_82575(struct e1000_hw *hw) 1191 { 1192 s32 ret_val; 1193 u16 speed, duplex; 1194 1195 DEBUGFUNC("e1000_check_for_link_82575"); 1196 1197 if (hw->phy.media_type != e1000_media_type_copper) { 1198 ret_val = e1000_get_pcs_speed_and_duplex_82575(hw, &speed, 1199 &duplex); 1200 /* 1201 * Use this flag to determine if link needs to be checked or 1202 * not. If we have link clear the flag so that we do not 1203 * continue to check for link. 1204 */ 1205 hw->mac.get_link_status = !hw->mac.serdes_has_link; 1206 1207 /* 1208 * Configure Flow Control now that Auto-Neg has completed. 1209 * First, we need to restore the desired flow control 1210 * settings because we may have had to re-autoneg with a 1211 * different link partner. 1212 */ 1213 ret_val = e1000_config_fc_after_link_up_generic(hw); 1214 if (ret_val) 1215 DEBUGOUT("Error configuring flow control\n"); 1216 } else { 1217 ret_val = e1000_check_for_copper_link_generic(hw); 1218 } 1219 1220 return ret_val; 1221 } 1222 1223 /** 1224 * e1000_check_for_link_media_swap - Check which M88E1112 interface linked 1225 * @hw: pointer to the HW structure 1226 * 1227 * Poll the M88E1112 interfaces to see which interface achieved link. 1228 */ 1229 static s32 e1000_check_for_link_media_swap(struct e1000_hw *hw) 1230 { 1231 struct e1000_phy_info *phy = &hw->phy; 1232 s32 ret_val; 1233 u16 data; 1234 u8 port = 0; 1235 1236 DEBUGFUNC("e1000_check_for_link_media_swap"); 1237 1238 /* Check the copper medium. */ 1239 ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 0); 1240 if (ret_val) 1241 return ret_val; 1242 1243 ret_val = phy->ops.read_reg(hw, E1000_M88E1112_STATUS, &data); 1244 if (ret_val) 1245 return ret_val; 1246 1247 if (data & E1000_M88E1112_STATUS_LINK) 1248 port = E1000_MEDIA_PORT_COPPER; 1249 1250 /* Check the other medium. */ 1251 ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 1); 1252 if (ret_val) 1253 return ret_val; 1254 1255 ret_val = phy->ops.read_reg(hw, E1000_M88E1112_STATUS, &data); 1256 if (ret_val) 1257 return ret_val; 1258 1259 /* reset page to 0 */ 1260 ret_val = phy->ops.write_reg(hw, E1000_M88E1112_PAGE_ADDR, 0); 1261 if (ret_val) 1262 return ret_val; 1263 1264 if (data & E1000_M88E1112_STATUS_LINK) 1265 port = E1000_MEDIA_PORT_OTHER; 1266 1267 /* Determine if a swap needs to happen. */ 1268 if (port && (hw->dev_spec._82575.media_port != port)) { 1269 hw->dev_spec._82575.media_port = port; 1270 hw->dev_spec._82575.media_changed = TRUE; 1271 } else { 1272 ret_val = e1000_check_for_link_82575(hw); 1273 } 1274 1275 return E1000_SUCCESS; 1276 } 1277 1278 /** 1279 * e1000_power_up_serdes_link_82575 - Power up the serdes link after shutdown 1280 * @hw: pointer to the HW structure 1281 **/ 1282 static void e1000_power_up_serdes_link_82575(struct e1000_hw *hw) 1283 { 1284 u32 reg; 1285 1286 DEBUGFUNC("e1000_power_up_serdes_link_82575"); 1287 1288 if ((hw->phy.media_type != e1000_media_type_internal_serdes) && 1289 !e1000_sgmii_active_82575(hw)) 1290 return; 1291 1292 /* Enable PCS to turn on link */ 1293 reg = E1000_READ_REG(hw, E1000_PCS_CFG0); 1294 reg |= E1000_PCS_CFG_PCS_EN; 1295 E1000_WRITE_REG(hw, E1000_PCS_CFG0, reg); 1296 1297 /* Power up the laser */ 1298 reg = E1000_READ_REG(hw, E1000_CTRL_EXT); 1299 reg &= ~E1000_CTRL_EXT_SDP3_DATA; 1300 E1000_WRITE_REG(hw, E1000_CTRL_EXT, reg); 1301 1302 /* flush the write to verify completion */ 1303 E1000_WRITE_FLUSH(hw); 1304 msec_delay(1); 1305 } 1306 1307 /** 1308 * e1000_get_pcs_speed_and_duplex_82575 - Retrieve current speed/duplex 1309 * @hw: pointer to the HW structure 1310 * @speed: stores the current speed 1311 * @duplex: stores the current duplex 1312 * 1313 * Using the physical coding sub-layer (PCS), retrieve the current speed and 1314 * duplex, then store the values in the pointers provided. 1315 **/ 1316 static s32 e1000_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw, 1317 u16 *speed, u16 *duplex) 1318 { 1319 struct e1000_mac_info *mac = &hw->mac; 1320 u32 pcs; 1321 u32 status; 1322 1323 DEBUGFUNC("e1000_get_pcs_speed_and_duplex_82575"); 1324 1325 /* 1326 * Read the PCS Status register for link state. For non-copper mode, 1327 * the status register is not accurate. The PCS status register is 1328 * used instead. 1329 */ 1330 pcs = E1000_READ_REG(hw, E1000_PCS_LSTAT); 1331 1332 /* 1333 * The link up bit determines when link is up on autoneg. 1334 */ 1335 if (pcs & E1000_PCS_LSTS_LINK_OK) { 1336 mac->serdes_has_link = TRUE; 1337 1338 /* Detect and store PCS speed */ 1339 if (pcs & E1000_PCS_LSTS_SPEED_1000) 1340 *speed = SPEED_1000; 1341 else if (pcs & E1000_PCS_LSTS_SPEED_100) 1342 *speed = SPEED_100; 1343 else 1344 *speed = SPEED_10; 1345 1346 /* Detect and store PCS duplex */ 1347 if (pcs & E1000_PCS_LSTS_DUPLEX_FULL) 1348 *duplex = FULL_DUPLEX; 1349 else 1350 *duplex = HALF_DUPLEX; 1351 1352 /* Check if it is an I354 2.5Gb backplane connection. */ 1353 if (mac->type == e1000_i354) { 1354 status = E1000_READ_REG(hw, E1000_STATUS); 1355 if ((status & E1000_STATUS_2P5_SKU) && 1356 !(status & E1000_STATUS_2P5_SKU_OVER)) { 1357 *speed = SPEED_2500; 1358 *duplex = FULL_DUPLEX; 1359 DEBUGOUT("2500 Mbs, "); 1360 DEBUGOUT("Full Duplex\n"); 1361 } 1362 } 1363 1364 } else { 1365 mac->serdes_has_link = FALSE; 1366 *speed = 0; 1367 *duplex = 0; 1368 } 1369 1370 return E1000_SUCCESS; 1371 } 1372 1373 /** 1374 * e1000_shutdown_serdes_link_82575 - Remove link during power down 1375 * @hw: pointer to the HW structure 1376 * 1377 * In the case of serdes shut down sfp and PCS on driver unload 1378 * when management pass thru is not enabled. 1379 **/ 1380 void e1000_shutdown_serdes_link_82575(struct e1000_hw *hw) 1381 { 1382 u32 reg; 1383 1384 DEBUGFUNC("e1000_shutdown_serdes_link_82575"); 1385 1386 if ((hw->phy.media_type != e1000_media_type_internal_serdes) && 1387 !e1000_sgmii_active_82575(hw)) 1388 return; 1389 1390 if (!e1000_enable_mng_pass_thru(hw)) { 1391 /* Disable PCS to turn off link */ 1392 reg = E1000_READ_REG(hw, E1000_PCS_CFG0); 1393 reg &= ~E1000_PCS_CFG_PCS_EN; 1394 E1000_WRITE_REG(hw, E1000_PCS_CFG0, reg); 1395 1396 /* shutdown the laser */ 1397 reg = E1000_READ_REG(hw, E1000_CTRL_EXT); 1398 reg |= E1000_CTRL_EXT_SDP3_DATA; 1399 E1000_WRITE_REG(hw, E1000_CTRL_EXT, reg); 1400 1401 /* flush the write to verify completion */ 1402 E1000_WRITE_FLUSH(hw); 1403 msec_delay(1); 1404 } 1405 1406 return; 1407 } 1408 1409 /** 1410 * e1000_reset_hw_82575 - Reset hardware 1411 * @hw: pointer to the HW structure 1412 * 1413 * This resets the hardware into a known state. 1414 **/ 1415 static s32 e1000_reset_hw_82575(struct e1000_hw *hw) 1416 { 1417 u32 ctrl; 1418 s32 ret_val; 1419 1420 DEBUGFUNC("e1000_reset_hw_82575"); 1421 1422 /* 1423 * Prevent the PCI-E bus from sticking if there is no TLP connection 1424 * on the last TLP read/write transaction when MAC is reset. 1425 */ 1426 ret_val = e1000_disable_pcie_master_generic(hw); 1427 if (ret_val) 1428 DEBUGOUT("PCI-E Master disable polling has failed.\n"); 1429 1430 /* set the completion timeout for interface */ 1431 ret_val = e1000_set_pcie_completion_timeout(hw); 1432 if (ret_val) 1433 DEBUGOUT("PCI-E Set completion timeout has failed.\n"); 1434 1435 DEBUGOUT("Masking off all interrupts\n"); 1436 E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); 1437 1438 E1000_WRITE_REG(hw, E1000_RCTL, 0); 1439 E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); 1440 E1000_WRITE_FLUSH(hw); 1441 1442 msec_delay(10); 1443 1444 ctrl = E1000_READ_REG(hw, E1000_CTRL); 1445 1446 DEBUGOUT("Issuing a global reset to MAC\n"); 1447 E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); 1448 1449 ret_val = e1000_get_auto_rd_done_generic(hw); 1450 if (ret_val) { 1451 /* 1452 * When auto config read does not complete, do not 1453 * return with an error. This can happen in situations 1454 * where there is no eeprom and prevents getting link. 1455 */ 1456 DEBUGOUT("Auto Read Done did not complete\n"); 1457 } 1458 1459 /* If EEPROM is not present, run manual init scripts */ 1460 if (!(E1000_READ_REG(hw, E1000_EECD) & E1000_EECD_PRES)) 1461 e1000_reset_init_script_82575(hw); 1462 1463 /* Clear any pending interrupt events. */ 1464 E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); 1465 E1000_READ_REG(hw, E1000_ICR); 1466 1467 /* Install any alternate MAC address into RAR0 */ 1468 ret_val = e1000_check_alt_mac_addr_generic(hw); 1469 1470 return ret_val; 1471 } 1472 1473 /** 1474 * e1000_init_hw_82575 - Initialize hardware 1475 * @hw: pointer to the HW structure 1476 * 1477 * This inits the hardware readying it for operation. 1478 **/ 1479 s32 e1000_init_hw_82575(struct e1000_hw *hw) 1480 { 1481 struct e1000_mac_info *mac = &hw->mac; 1482 s32 ret_val; 1483 u16 i, rar_count = mac->rar_entry_count; 1484 1485 DEBUGFUNC("e1000_init_hw_82575"); 1486 1487 /* Initialize identification LED */ 1488 ret_val = mac->ops.id_led_init(hw); 1489 if (ret_val) { 1490 DEBUGOUT("Error initializing identification LED\n"); 1491 /* This is not fatal and we should not stop init due to this */ 1492 } 1493 1494 /* Disabling VLAN filtering */ 1495 DEBUGOUT("Initializing the IEEE VLAN\n"); 1496 mac->ops.clear_vfta(hw); 1497 1498 /* Setup the receive address */ 1499 e1000_init_rx_addrs_generic(hw, rar_count); 1500 1501 /* Zero out the Multicast HASH table */ 1502 DEBUGOUT("Zeroing the MTA\n"); 1503 for (i = 0; i < mac->mta_reg_count; i++) 1504 E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); 1505 1506 /* Zero out the Unicast HASH table */ 1507 DEBUGOUT("Zeroing the UTA\n"); 1508 for (i = 0; i < mac->uta_reg_count; i++) 1509 E1000_WRITE_REG_ARRAY(hw, E1000_UTA, i, 0); 1510 1511 /* Setup link and flow control */ 1512 ret_val = mac->ops.setup_link(hw); 1513 1514 /* Set the default MTU size */ 1515 hw->dev_spec._82575.mtu = 1500; 1516 1517 /* 1518 * Clear all of the statistics registers (clear on read). It is 1519 * important that we do this after we have tried to establish link 1520 * because the symbol error count will increment wildly if there 1521 * is no link. 1522 */ 1523 e1000_clear_hw_cntrs_82575(hw); 1524 1525 return ret_val; 1526 } 1527 1528 /** 1529 * e1000_setup_copper_link_82575 - Configure copper link settings 1530 * @hw: pointer to the HW structure 1531 * 1532 * Configures the link for auto-neg or forced speed and duplex. Then we check 1533 * for link, once link is established calls to configure collision distance 1534 * and flow control are called. 1535 **/ 1536 static s32 e1000_setup_copper_link_82575(struct e1000_hw *hw) 1537 { 1538 u32 ctrl; 1539 s32 ret_val; 1540 u32 phpm_reg; 1541 1542 DEBUGFUNC("e1000_setup_copper_link_82575"); 1543 1544 ctrl = E1000_READ_REG(hw, E1000_CTRL); 1545 ctrl |= E1000_CTRL_SLU; 1546 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 1547 E1000_WRITE_REG(hw, E1000_CTRL, ctrl); 1548 1549 /* Clear Go Link Disconnect bit on supported devices */ 1550 switch (hw->mac.type) { 1551 case e1000_82580: 1552 case e1000_i350: 1553 case e1000_i210: 1554 case e1000_i211: 1555 phpm_reg = E1000_READ_REG(hw, E1000_82580_PHY_POWER_MGMT); 1556 phpm_reg &= ~E1000_82580_PM_GO_LINKD; 1557 E1000_WRITE_REG(hw, E1000_82580_PHY_POWER_MGMT, phpm_reg); 1558 break; 1559 default: 1560 break; 1561 } 1562 1563 ret_val = e1000_setup_serdes_link_82575(hw); 1564 if (ret_val) 1565 goto out; 1566 1567 if (e1000_sgmii_active_82575(hw)) { 1568 /* allow time for SFP cage time to power up phy */ 1569 msec_delay(300); 1570 1571 ret_val = hw->phy.ops.reset(hw); 1572 if (ret_val) { 1573 DEBUGOUT("Error resetting the PHY.\n"); 1574 goto out; 1575 } 1576 } 1577 switch (hw->phy.type) { 1578 case e1000_phy_i210: 1579 case e1000_phy_m88: 1580 switch (hw->phy.id) { 1581 case I347AT4_E_PHY_ID: 1582 case M88E1112_E_PHY_ID: 1583 case M88E1340M_E_PHY_ID: 1584 case M88E1543_E_PHY_ID: 1585 case M88E1512_E_PHY_ID: 1586 case I210_I_PHY_ID: 1587 ret_val = e1000_copper_link_setup_m88_gen2(hw); 1588 break; 1589 default: 1590 ret_val = e1000_copper_link_setup_m88(hw); 1591 break; 1592 } 1593 break; 1594 case e1000_phy_igp_3: 1595 ret_val = e1000_copper_link_setup_igp(hw); 1596 break; 1597 case e1000_phy_82580: 1598 ret_val = e1000_copper_link_setup_82577(hw); 1599 break; 1600 default: 1601 ret_val = -E1000_ERR_PHY; 1602 break; 1603 } 1604 1605 if (ret_val) 1606 goto out; 1607 1608 ret_val = e1000_setup_copper_link_generic(hw); 1609 out: 1610 return ret_val; 1611 } 1612 1613 /** 1614 * e1000_setup_serdes_link_82575 - Setup link for serdes 1615 * @hw: pointer to the HW structure 1616 * 1617 * Configure the physical coding sub-layer (PCS) link. The PCS link is 1618 * used on copper connections where the serialized gigabit media independent 1619 * interface (sgmii), or serdes fiber is being used. Configures the link 1620 * for auto-negotiation or forces speed/duplex. 1621 **/ 1622 static s32 e1000_setup_serdes_link_82575(struct e1000_hw *hw) 1623 { 1624 u32 ctrl_ext, ctrl_reg, reg, anadv_reg; 1625 bool pcs_autoneg; 1626 s32 ret_val = E1000_SUCCESS; 1627 u16 data; 1628 1629 DEBUGFUNC("e1000_setup_serdes_link_82575"); 1630 1631 if ((hw->phy.media_type != e1000_media_type_internal_serdes) && 1632 !e1000_sgmii_active_82575(hw)) 1633 return ret_val; 1634 1635 /* 1636 * On the 82575, SerDes loopback mode persists until it is 1637 * explicitly turned off or a power cycle is performed. A read to 1638 * the register does not indicate its status. Therefore, we ensure 1639 * loopback mode is disabled during initialization. 1640 */ 1641 E1000_WRITE_REG(hw, E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK); 1642 1643 /* power on the sfp cage if present */ 1644 ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); 1645 ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA; 1646 E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); 1647 1648 ctrl_reg = E1000_READ_REG(hw, E1000_CTRL); 1649 ctrl_reg |= E1000_CTRL_SLU; 1650 1651 /* set both sw defined pins on 82575/82576*/ 1652 if (hw->mac.type == e1000_82575 || hw->mac.type == e1000_82576) 1653 ctrl_reg |= E1000_CTRL_SWDPIN0 | E1000_CTRL_SWDPIN1; 1654 1655 reg = E1000_READ_REG(hw, E1000_PCS_LCTL); 1656 1657 /* default pcs_autoneg to the same setting as mac autoneg */ 1658 pcs_autoneg = hw->mac.autoneg; 1659 1660 switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) { 1661 case E1000_CTRL_EXT_LINK_MODE_SGMII: 1662 /* sgmii mode lets the phy handle forcing speed/duplex */ 1663 pcs_autoneg = TRUE; 1664 /* autoneg time out should be disabled for SGMII mode */ 1665 reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT); 1666 break; 1667 case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX: 1668 /* disable PCS autoneg and support parallel detect only */ 1669 pcs_autoneg = FALSE; 1670 /* fall through to default case */ 1671 default: 1672 if (hw->mac.type == e1000_82575 || 1673 hw->mac.type == e1000_82576) { 1674 ret_val = hw->nvm.ops.read(hw, NVM_COMPAT, 1, &data); 1675 if (ret_val) { 1676 DEBUGOUT("NVM Read Error\n"); 1677 return ret_val; 1678 } 1679 1680 if (data & E1000_EEPROM_PCS_AUTONEG_DISABLE_BIT) 1681 pcs_autoneg = FALSE; 1682 } 1683 1684 /* 1685 * non-SGMII modes only supports a speed of 1000/Full for the 1686 * link so it is best to just force the MAC and let the pcs 1687 * link either autoneg or be forced to 1000/Full 1688 */ 1689 ctrl_reg |= E1000_CTRL_SPD_1000 | E1000_CTRL_FRCSPD | 1690 E1000_CTRL_FD | E1000_CTRL_FRCDPX; 1691 1692 /* set speed of 1000/Full if speed/duplex is forced */ 1693 reg |= E1000_PCS_LCTL_FSV_1000 | E1000_PCS_LCTL_FDV_FULL; 1694 break; 1695 } 1696 1697 E1000_WRITE_REG(hw, E1000_CTRL, ctrl_reg); 1698 1699 /* 1700 * New SerDes mode allows for forcing speed or autonegotiating speed 1701 * at 1gb. Autoneg should be default set by most drivers. This is the 1702 * mode that will be compatible with older link partners and switches. 1703 * However, both are supported by the hardware and some drivers/tools. 1704 */ 1705 reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP | 1706 E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK); 1707 1708 if (pcs_autoneg) { 1709 /* Set PCS register for autoneg */ 1710 reg |= E1000_PCS_LCTL_AN_ENABLE | /* Enable Autoneg */ 1711 E1000_PCS_LCTL_AN_RESTART; /* Restart autoneg */ 1712 1713 /* Disable force flow control for autoneg */ 1714 reg &= ~E1000_PCS_LCTL_FORCE_FCTRL; 1715 1716 /* Configure flow control advertisement for autoneg */ 1717 anadv_reg = E1000_READ_REG(hw, E1000_PCS_ANADV); 1718 anadv_reg &= ~(E1000_TXCW_ASM_DIR | E1000_TXCW_PAUSE); 1719 1720 switch (hw->fc.requested_mode) { 1721 case e1000_fc_full: 1722 case e1000_fc_rx_pause: 1723 anadv_reg |= E1000_TXCW_ASM_DIR; 1724 anadv_reg |= E1000_TXCW_PAUSE; 1725 break; 1726 case e1000_fc_tx_pause: 1727 anadv_reg |= E1000_TXCW_ASM_DIR; 1728 break; 1729 default: 1730 break; 1731 } 1732 1733 E1000_WRITE_REG(hw, E1000_PCS_ANADV, anadv_reg); 1734 1735 DEBUGOUT1("Configuring Autoneg:PCS_LCTL=0x%08X\n", reg); 1736 } else { 1737 /* Set PCS register for forced link */ 1738 reg |= E1000_PCS_LCTL_FSD; /* Force Speed */ 1739 1740 /* Force flow control for forced link */ 1741 reg |= E1000_PCS_LCTL_FORCE_FCTRL; 1742 1743 DEBUGOUT1("Configuring Forced Link:PCS_LCTL=0x%08X\n", reg); 1744 } 1745 1746 E1000_WRITE_REG(hw, E1000_PCS_LCTL, reg); 1747 1748 if (!pcs_autoneg && !e1000_sgmii_active_82575(hw)) 1749 e1000_force_mac_fc_generic(hw); 1750 1751 return ret_val; 1752 } 1753 1754 /** 1755 * e1000_get_media_type_82575 - derives current media type. 1756 * @hw: pointer to the HW structure 1757 * 1758 * The media type is chosen reflecting few settings. 1759 * The following are taken into account: 1760 * - link mode set in the current port Init Control Word #3 1761 * - current link mode settings in CSR register 1762 * - MDIO vs. I2C PHY control interface chosen 1763 * - SFP module media type 1764 **/ 1765 static s32 e1000_get_media_type_82575(struct e1000_hw *hw) 1766 { 1767 struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575; 1768 s32 ret_val = E1000_SUCCESS; 1769 u32 ctrl_ext = 0; 1770 u32 link_mode = 0; 1771 1772 /* Set internal phy as default */ 1773 dev_spec->sgmii_active = FALSE; 1774 dev_spec->module_plugged = FALSE; 1775 1776 /* Get CSR setting */ 1777 ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); 1778 1779 /* extract link mode setting */ 1780 link_mode = ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK; 1781 1782 switch (link_mode) { 1783 case E1000_CTRL_EXT_LINK_MODE_1000BASE_KX: 1784 hw->phy.media_type = e1000_media_type_internal_serdes; 1785 break; 1786 case E1000_CTRL_EXT_LINK_MODE_GMII: 1787 hw->phy.media_type = e1000_media_type_copper; 1788 break; 1789 case E1000_CTRL_EXT_LINK_MODE_SGMII: 1790 /* Get phy control interface type set (MDIO vs. I2C)*/ 1791 if (e1000_sgmii_uses_mdio_82575(hw)) { 1792 hw->phy.media_type = e1000_media_type_copper; 1793 dev_spec->sgmii_active = TRUE; 1794 break; 1795 } 1796 /* fall through for I2C based SGMII */ 1797 case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES: 1798 /* read media type from SFP EEPROM */ 1799 ret_val = e1000_set_sfp_media_type_82575(hw); 1800 if ((ret_val != E1000_SUCCESS) || 1801 (hw->phy.media_type == e1000_media_type_unknown)) { 1802 /* 1803 * If media type was not identified then return media 1804 * type defined by the CTRL_EXT settings. 1805 */ 1806 hw->phy.media_type = e1000_media_type_internal_serdes; 1807 1808 if (link_mode == E1000_CTRL_EXT_LINK_MODE_SGMII) { 1809 hw->phy.media_type = e1000_media_type_copper; 1810 dev_spec->sgmii_active = TRUE; 1811 } 1812 1813 break; 1814 } 1815 1816 /* do not change link mode for 100BaseFX */ 1817 if (dev_spec->eth_flags.e100_base_fx) 1818 break; 1819 1820 /* change current link mode setting */ 1821 ctrl_ext &= ~E1000_CTRL_EXT_LINK_MODE_MASK; 1822 1823 if (hw->phy.media_type == e1000_media_type_copper) 1824 ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_SGMII; 1825 else 1826 ctrl_ext |= E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES; 1827 1828 E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); 1829 1830 break; 1831 } 1832 1833 return ret_val; 1834 } 1835 1836 /** 1837 * e1000_set_sfp_media_type_82575 - derives SFP module media type. 1838 * @hw: pointer to the HW structure 1839 * 1840 * The media type is chosen based on SFP module. 1841 * compatibility flags retrieved from SFP ID EEPROM. 1842 **/ 1843 static s32 e1000_set_sfp_media_type_82575(struct e1000_hw *hw) 1844 { 1845 s32 ret_val = E1000_ERR_CONFIG; 1846 u32 ctrl_ext = 0; 1847 struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575; 1848 struct sfp_e1000_flags *eth_flags = &dev_spec->eth_flags; 1849 u8 tranceiver_type = 0; 1850 s32 timeout = 3; 1851 1852 /* Turn I2C interface ON and power on sfp cage */ 1853 ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); 1854 ctrl_ext &= ~E1000_CTRL_EXT_SDP3_DATA; 1855 E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext | E1000_CTRL_I2C_ENA); 1856 1857 E1000_WRITE_FLUSH(hw); 1858 1859 /* Read SFP module data */ 1860 while (timeout) { 1861 ret_val = e1000_read_sfp_data_byte(hw, 1862 E1000_I2CCMD_SFP_DATA_ADDR(E1000_SFF_IDENTIFIER_OFFSET), 1863 &tranceiver_type); 1864 if (ret_val == E1000_SUCCESS) 1865 break; 1866 msec_delay(100); 1867 timeout--; 1868 } 1869 if (ret_val != E1000_SUCCESS) 1870 goto out; 1871 1872 ret_val = e1000_read_sfp_data_byte(hw, 1873 E1000_I2CCMD_SFP_DATA_ADDR(E1000_SFF_ETH_FLAGS_OFFSET), 1874 (u8 *)eth_flags); 1875 if (ret_val != E1000_SUCCESS) 1876 goto out; 1877 1878 /* Check if there is some SFP module plugged and powered */ 1879 if ((tranceiver_type == E1000_SFF_IDENTIFIER_SFP) || 1880 (tranceiver_type == E1000_SFF_IDENTIFIER_SFF)) { 1881 dev_spec->module_plugged = TRUE; 1882 if (eth_flags->e1000_base_lx || eth_flags->e1000_base_sx) { 1883 hw->phy.media_type = e1000_media_type_internal_serdes; 1884 } else if (eth_flags->e100_base_fx) { 1885 dev_spec->sgmii_active = TRUE; 1886 hw->phy.media_type = e1000_media_type_internal_serdes; 1887 } else if (eth_flags->e1000_base_t) { 1888 dev_spec->sgmii_active = TRUE; 1889 hw->phy.media_type = e1000_media_type_copper; 1890 } else { 1891 hw->phy.media_type = e1000_media_type_unknown; 1892 DEBUGOUT("PHY module has not been recognized\n"); 1893 goto out; 1894 } 1895 } else { 1896 hw->phy.media_type = e1000_media_type_unknown; 1897 } 1898 ret_val = E1000_SUCCESS; 1899 out: 1900 /* Restore I2C interface setting */ 1901 E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); 1902 return ret_val; 1903 } 1904 1905 /** 1906 * e1000_valid_led_default_82575 - Verify a valid default LED config 1907 * @hw: pointer to the HW structure 1908 * @data: pointer to the NVM (EEPROM) 1909 * 1910 * Read the EEPROM for the current default LED configuration. If the 1911 * LED configuration is not valid, set to a valid LED configuration. 1912 **/ 1913 static s32 e1000_valid_led_default_82575(struct e1000_hw *hw, u16 *data) 1914 { 1915 s32 ret_val; 1916 1917 DEBUGFUNC("e1000_valid_led_default_82575"); 1918 1919 ret_val = hw->nvm.ops.read(hw, NVM_ID_LED_SETTINGS, 1, data); 1920 if (ret_val) { 1921 DEBUGOUT("NVM Read Error\n"); 1922 goto out; 1923 } 1924 1925 if (*data == ID_LED_RESERVED_0000 || *data == ID_LED_RESERVED_FFFF) { 1926 switch (hw->phy.media_type) { 1927 case e1000_media_type_internal_serdes: 1928 *data = ID_LED_DEFAULT_82575_SERDES; 1929 break; 1930 case e1000_media_type_copper: 1931 default: 1932 *data = ID_LED_DEFAULT; 1933 break; 1934 } 1935 } 1936 out: 1937 return ret_val; 1938 } 1939 1940 /** 1941 * e1000_sgmii_active_82575 - Return sgmii state 1942 * @hw: pointer to the HW structure 1943 * 1944 * 82575 silicon has a serialized gigabit media independent interface (sgmii) 1945 * which can be enabled for use in the embedded applications. Simply 1946 * return the current state of the sgmii interface. 1947 **/ 1948 static bool e1000_sgmii_active_82575(struct e1000_hw *hw) 1949 { 1950 struct e1000_dev_spec_82575 *dev_spec = &hw->dev_spec._82575; 1951 return dev_spec->sgmii_active; 1952 } 1953 1954 /** 1955 * e1000_reset_init_script_82575 - Inits HW defaults after reset 1956 * @hw: pointer to the HW structure 1957 * 1958 * Inits recommended HW defaults after a reset when there is no EEPROM 1959 * detected. This is only for the 82575. 1960 **/ 1961 static s32 e1000_reset_init_script_82575(struct e1000_hw *hw) 1962 { 1963 DEBUGFUNC("e1000_reset_init_script_82575"); 1964 1965 if (hw->mac.type == e1000_82575) { 1966 DEBUGOUT("Running reset init script for 82575\n"); 1967 /* SerDes configuration via SERDESCTRL */ 1968 e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCTL, 0x00, 0x0C); 1969 e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCTL, 0x01, 0x78); 1970 e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCTL, 0x1B, 0x23); 1971 e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCTL, 0x23, 0x15); 1972 1973 /* CCM configuration via CCMCTL register */ 1974 e1000_write_8bit_ctrl_reg_generic(hw, E1000_CCMCTL, 0x14, 0x00); 1975 e1000_write_8bit_ctrl_reg_generic(hw, E1000_CCMCTL, 0x10, 0x00); 1976 1977 /* PCIe lanes configuration */ 1978 e1000_write_8bit_ctrl_reg_generic(hw, E1000_GIOCTL, 0x00, 0xEC); 1979 e1000_write_8bit_ctrl_reg_generic(hw, E1000_GIOCTL, 0x61, 0xDF); 1980 e1000_write_8bit_ctrl_reg_generic(hw, E1000_GIOCTL, 0x34, 0x05); 1981 e1000_write_8bit_ctrl_reg_generic(hw, E1000_GIOCTL, 0x2F, 0x81); 1982 1983 /* PCIe PLL Configuration */ 1984 e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCCTL, 0x02, 0x47); 1985 e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCCTL, 0x14, 0x00); 1986 e1000_write_8bit_ctrl_reg_generic(hw, E1000_SCCTL, 0x10, 0x00); 1987 } 1988 1989 return E1000_SUCCESS; 1990 } 1991 1992 /** 1993 * e1000_read_mac_addr_82575 - Read device MAC address 1994 * @hw: pointer to the HW structure 1995 **/ 1996 static s32 e1000_read_mac_addr_82575(struct e1000_hw *hw) 1997 { 1998 s32 ret_val; 1999 2000 DEBUGFUNC("e1000_read_mac_addr_82575"); 2001 2002 /* 2003 * If there's an alternate MAC address place it in RAR0 2004 * so that it will override the Si installed default perm 2005 * address. 2006 */ 2007 ret_val = e1000_check_alt_mac_addr_generic(hw); 2008 if (ret_val) 2009 goto out; 2010 2011 ret_val = e1000_read_mac_addr_generic(hw); 2012 2013 out: 2014 return ret_val; 2015 } 2016 2017 /** 2018 * e1000_config_collision_dist_82575 - Configure collision distance 2019 * @hw: pointer to the HW structure 2020 * 2021 * Configures the collision distance to the default value and is used 2022 * during link setup. 2023 **/ 2024 static void e1000_config_collision_dist_82575(struct e1000_hw *hw) 2025 { 2026 u32 tctl_ext; 2027 2028 DEBUGFUNC("e1000_config_collision_dist_82575"); 2029 2030 tctl_ext = E1000_READ_REG(hw, E1000_TCTL_EXT); 2031 2032 tctl_ext &= ~E1000_TCTL_EXT_COLD; 2033 tctl_ext |= E1000_COLLISION_DISTANCE << E1000_TCTL_EXT_COLD_SHIFT; 2034 2035 E1000_WRITE_REG(hw, E1000_TCTL_EXT, tctl_ext); 2036 E1000_WRITE_FLUSH(hw); 2037 } 2038 2039 /** 2040 * e1000_power_down_phy_copper_82575 - Remove link during PHY power down 2041 * @hw: pointer to the HW structure 2042 * 2043 * In the case of a PHY power down to save power, or to turn off link during a 2044 * driver unload, or wake on lan is not enabled, remove the link. 2045 **/ 2046 static void e1000_power_down_phy_copper_82575(struct e1000_hw *hw) 2047 { 2048 struct e1000_phy_info *phy = &hw->phy; 2049 2050 if (!(phy->ops.check_reset_block)) 2051 return; 2052 2053 /* If the management interface is not enabled, then power down */ 2054 if (!(e1000_enable_mng_pass_thru(hw) || phy->ops.check_reset_block(hw))) 2055 e1000_power_down_phy_copper(hw); 2056 2057 return; 2058 } 2059 2060 /** 2061 * e1000_clear_hw_cntrs_82575 - Clear device specific hardware counters 2062 * @hw: pointer to the HW structure 2063 * 2064 * Clears the hardware counters by reading the counter registers. 2065 **/ 2066 static void e1000_clear_hw_cntrs_82575(struct e1000_hw *hw) 2067 { 2068 DEBUGFUNC("e1000_clear_hw_cntrs_82575"); 2069 2070 e1000_clear_hw_cntrs_base_generic(hw); 2071 2072 E1000_READ_REG(hw, E1000_PRC64); 2073 E1000_READ_REG(hw, E1000_PRC127); 2074 E1000_READ_REG(hw, E1000_PRC255); 2075 E1000_READ_REG(hw, E1000_PRC511); 2076 E1000_READ_REG(hw, E1000_PRC1023); 2077 E1000_READ_REG(hw, E1000_PRC1522); 2078 E1000_READ_REG(hw, E1000_PTC64); 2079 E1000_READ_REG(hw, E1000_PTC127); 2080 E1000_READ_REG(hw, E1000_PTC255); 2081 E1000_READ_REG(hw, E1000_PTC511); 2082 E1000_READ_REG(hw, E1000_PTC1023); 2083 E1000_READ_REG(hw, E1000_PTC1522); 2084 2085 E1000_READ_REG(hw, E1000_ALGNERRC); 2086 E1000_READ_REG(hw, E1000_RXERRC); 2087 E1000_READ_REG(hw, E1000_TNCRS); 2088 E1000_READ_REG(hw, E1000_CEXTERR); 2089 E1000_READ_REG(hw, E1000_TSCTC); 2090 E1000_READ_REG(hw, E1000_TSCTFC); 2091 2092 E1000_READ_REG(hw, E1000_MGTPRC); 2093 E1000_READ_REG(hw, E1000_MGTPDC); 2094 E1000_READ_REG(hw, E1000_MGTPTC); 2095 2096 E1000_READ_REG(hw, E1000_IAC); 2097 E1000_READ_REG(hw, E1000_ICRXOC); 2098 2099 E1000_READ_REG(hw, E1000_ICRXPTC); 2100 E1000_READ_REG(hw, E1000_ICRXATC); 2101 E1000_READ_REG(hw, E1000_ICTXPTC); 2102 E1000_READ_REG(hw, E1000_ICTXATC); 2103 E1000_READ_REG(hw, E1000_ICTXQEC); 2104 E1000_READ_REG(hw, E1000_ICTXQMTC); 2105 E1000_READ_REG(hw, E1000_ICRXDMTC); 2106 2107 E1000_READ_REG(hw, E1000_CBTMPC); 2108 E1000_READ_REG(hw, E1000_HTDPMC); 2109 E1000_READ_REG(hw, E1000_CBRMPC); 2110 E1000_READ_REG(hw, E1000_RPTHC); 2111 E1000_READ_REG(hw, E1000_HGPTC); 2112 E1000_READ_REG(hw, E1000_HTCBDPC); 2113 E1000_READ_REG(hw, E1000_HGORCL); 2114 E1000_READ_REG(hw, E1000_HGORCH); 2115 E1000_READ_REG(hw, E1000_HGOTCL); 2116 E1000_READ_REG(hw, E1000_HGOTCH); 2117 E1000_READ_REG(hw, E1000_LENERRS); 2118 2119 /* This register should not be read in copper configurations */ 2120 if ((hw->phy.media_type == e1000_media_type_internal_serdes) || 2121 e1000_sgmii_active_82575(hw)) 2122 E1000_READ_REG(hw, E1000_SCVPC); 2123 } 2124 2125 /** 2126 * e1000_rx_fifo_flush_82575 - Clean rx fifo after Rx enable 2127 * @hw: pointer to the HW structure 2128 * 2129 * After rx enable if managability is enabled then there is likely some 2130 * bad data at the start of the fifo and possibly in the DMA fifo. This 2131 * function clears the fifos and flushes any packets that came in as rx was 2132 * being enabled. 2133 **/ 2134 void e1000_rx_fifo_flush_82575(struct e1000_hw *hw) 2135 { 2136 u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled; 2137 int i, ms_wait; 2138 2139 DEBUGFUNC("e1000_rx_fifo_workaround_82575"); 2140 if (hw->mac.type != e1000_82575 || 2141 !(E1000_READ_REG(hw, E1000_MANC) & E1000_MANC_RCV_TCO_EN)) 2142 return; 2143 2144 /* Disable all Rx queues */ 2145 for (i = 0; i < 4; i++) { 2146 rxdctl[i] = E1000_READ_REG(hw, E1000_RXDCTL(i)); 2147 E1000_WRITE_REG(hw, E1000_RXDCTL(i), 2148 rxdctl[i] & ~E1000_RXDCTL_QUEUE_ENABLE); 2149 } 2150 /* Poll all queues to verify they have shut down */ 2151 for (ms_wait = 0; ms_wait < 10; ms_wait++) { 2152 msec_delay(1); 2153 rx_enabled = 0; 2154 for (i = 0; i < 4; i++) 2155 rx_enabled |= E1000_READ_REG(hw, E1000_RXDCTL(i)); 2156 if (!(rx_enabled & E1000_RXDCTL_QUEUE_ENABLE)) 2157 break; 2158 } 2159 2160 if (ms_wait == 10) 2161 DEBUGOUT("Queue disable timed out after 10ms\n"); 2162 2163 /* Clear RLPML, RCTL.SBP, RFCTL.LEF, and set RCTL.LPE so that all 2164 * incoming packets are rejected. Set enable and wait 2ms so that 2165 * any packet that was coming in as RCTL.EN was set is flushed 2166 */ 2167 rfctl = E1000_READ_REG(hw, E1000_RFCTL); 2168 E1000_WRITE_REG(hw, E1000_RFCTL, rfctl & ~E1000_RFCTL_LEF); 2169 2170 rlpml = E1000_READ_REG(hw, E1000_RLPML); 2171 E1000_WRITE_REG(hw, E1000_RLPML, 0); 2172 2173 rctl = E1000_READ_REG(hw, E1000_RCTL); 2174 temp_rctl = rctl & ~(E1000_RCTL_EN | E1000_RCTL_SBP); 2175 temp_rctl |= E1000_RCTL_LPE; 2176 2177 E1000_WRITE_REG(hw, E1000_RCTL, temp_rctl); 2178 E1000_WRITE_REG(hw, E1000_RCTL, temp_rctl | E1000_RCTL_EN); 2179 E1000_WRITE_FLUSH(hw); 2180 msec_delay(2); 2181 2182 /* Enable Rx queues that were previously enabled and restore our 2183 * previous state 2184 */ 2185 for (i = 0; i < 4; i++) 2186 E1000_WRITE_REG(hw, E1000_RXDCTL(i), rxdctl[i]); 2187 E1000_WRITE_REG(hw, E1000_RCTL, rctl); 2188 E1000_WRITE_FLUSH(hw); 2189 2190 E1000_WRITE_REG(hw, E1000_RLPML, rlpml); 2191 E1000_WRITE_REG(hw, E1000_RFCTL, rfctl); 2192 2193 /* Flush receive errors generated by workaround */ 2194 E1000_READ_REG(hw, E1000_ROC); 2195 E1000_READ_REG(hw, E1000_RNBC); 2196 E1000_READ_REG(hw, E1000_MPC); 2197 } 2198 2199 /** 2200 * e1000_set_pcie_completion_timeout - set pci-e completion timeout 2201 * @hw: pointer to the HW structure 2202 * 2203 * The defaults for 82575 and 82576 should be in the range of 50us to 50ms, 2204 * however the hardware default for these parts is 500us to 1ms which is less 2205 * than the 10ms recommended by the pci-e spec. To address this we need to 2206 * increase the value to either 10ms to 200ms for capability version 1 config, 2207 * or 16ms to 55ms for version 2. 2208 **/ 2209 static s32 e1000_set_pcie_completion_timeout(struct e1000_hw *hw) 2210 { 2211 u32 gcr = E1000_READ_REG(hw, E1000_GCR); 2212 s32 ret_val = E1000_SUCCESS; 2213 u16 pcie_devctl2; 2214 2215 /* only take action if timeout value is defaulted to 0 */ 2216 if (gcr & E1000_GCR_CMPL_TMOUT_MASK) 2217 goto out; 2218 2219 /* 2220 * if capababilities version is type 1 we can write the 2221 * timeout of 10ms to 200ms through the GCR register 2222 */ 2223 if (!(gcr & E1000_GCR_CAP_VER2)) { 2224 gcr |= E1000_GCR_CMPL_TMOUT_10ms; 2225 goto out; 2226 } 2227 2228 /* 2229 * for version 2 capabilities we need to write the config space 2230 * directly in order to set the completion timeout value for 2231 * 16ms to 55ms 2232 */ 2233 ret_val = e1000_read_pcie_cap_reg(hw, PCIE_DEVICE_CONTROL2, 2234 &pcie_devctl2); 2235 if (ret_val) 2236 goto out; 2237 2238 pcie_devctl2 |= PCIE_DEVICE_CONTROL2_16ms; 2239 2240 ret_val = e1000_write_pcie_cap_reg(hw, PCIE_DEVICE_CONTROL2, 2241 &pcie_devctl2); 2242 out: 2243 /* disable completion timeout resend */ 2244 gcr &= ~E1000_GCR_CMPL_TMOUT_RESEND; 2245 2246 E1000_WRITE_REG(hw, E1000_GCR, gcr); 2247 return ret_val; 2248 } 2249 2250 /** 2251 * e1000_vmdq_set_anti_spoofing_pf - enable or disable anti-spoofing 2252 * @hw: pointer to the hardware struct 2253 * @enable: state to enter, either enabled or disabled 2254 * @pf: Physical Function pool - do not set anti-spoofing for the PF 2255 * 2256 * enables/disables L2 switch anti-spoofing functionality. 2257 **/ 2258 void e1000_vmdq_set_anti_spoofing_pf(struct e1000_hw *hw, bool enable, int pf) 2259 { 2260 u32 reg_val, reg_offset; 2261 2262 switch (hw->mac.type) { 2263 case e1000_82576: 2264 reg_offset = E1000_DTXSWC; 2265 break; 2266 case e1000_i350: 2267 case e1000_i354: 2268 reg_offset = E1000_TXSWC; 2269 break; 2270 default: 2271 return; 2272 } 2273 2274 reg_val = E1000_READ_REG(hw, reg_offset); 2275 if (enable) { 2276 reg_val |= (E1000_DTXSWC_MAC_SPOOF_MASK | 2277 E1000_DTXSWC_VLAN_SPOOF_MASK); 2278 /* The PF can spoof - it has to in order to 2279 * support emulation mode NICs 2280 */ 2281 reg_val ^= (1 << pf | 1 << (pf + MAX_NUM_VFS)); 2282 } else { 2283 reg_val &= ~(E1000_DTXSWC_MAC_SPOOF_MASK | 2284 E1000_DTXSWC_VLAN_SPOOF_MASK); 2285 } 2286 E1000_WRITE_REG(hw, reg_offset, reg_val); 2287 } 2288 2289 /** 2290 * e1000_vmdq_set_loopback_pf - enable or disable vmdq loopback 2291 * @hw: pointer to the hardware struct 2292 * @enable: state to enter, either enabled or disabled 2293 * 2294 * enables/disables L2 switch loopback functionality. 2295 **/ 2296 void e1000_vmdq_set_loopback_pf(struct e1000_hw *hw, bool enable) 2297 { 2298 u32 dtxswc; 2299 2300 switch (hw->mac.type) { 2301 case e1000_82576: 2302 dtxswc = E1000_READ_REG(hw, E1000_DTXSWC); 2303 if (enable) 2304 dtxswc |= E1000_DTXSWC_VMDQ_LOOPBACK_EN; 2305 else 2306 dtxswc &= ~E1000_DTXSWC_VMDQ_LOOPBACK_EN; 2307 E1000_WRITE_REG(hw, E1000_DTXSWC, dtxswc); 2308 break; 2309 case e1000_i350: 2310 case e1000_i354: 2311 dtxswc = E1000_READ_REG(hw, E1000_TXSWC); 2312 if (enable) 2313 dtxswc |= E1000_DTXSWC_VMDQ_LOOPBACK_EN; 2314 else 2315 dtxswc &= ~E1000_DTXSWC_VMDQ_LOOPBACK_EN; 2316 E1000_WRITE_REG(hw, E1000_TXSWC, dtxswc); 2317 break; 2318 default: 2319 /* Currently no other hardware supports loopback */ 2320 break; 2321 } 2322 2323 2324 } 2325 2326 /** 2327 * e1000_vmdq_set_replication_pf - enable or disable vmdq replication 2328 * @hw: pointer to the hardware struct 2329 * @enable: state to enter, either enabled or disabled 2330 * 2331 * enables/disables replication of packets across multiple pools. 2332 **/ 2333 void e1000_vmdq_set_replication_pf(struct e1000_hw *hw, bool enable) 2334 { 2335 u32 vt_ctl = E1000_READ_REG(hw, E1000_VT_CTL); 2336 2337 if (enable) 2338 vt_ctl |= E1000_VT_CTL_VM_REPL_EN; 2339 else 2340 vt_ctl &= ~E1000_VT_CTL_VM_REPL_EN; 2341 2342 E1000_WRITE_REG(hw, E1000_VT_CTL, vt_ctl); 2343 } 2344 2345 /** 2346 * e1000_read_phy_reg_82580 - Read 82580 MDI control register 2347 * @hw: pointer to the HW structure 2348 * @offset: register offset to be read 2349 * @data: pointer to the read data 2350 * 2351 * Reads the MDI control register in the PHY at offset and stores the 2352 * information read to data. 2353 **/ 2354 static s32 e1000_read_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 *data) 2355 { 2356 s32 ret_val; 2357 2358 DEBUGFUNC("e1000_read_phy_reg_82580"); 2359 2360 ret_val = hw->phy.ops.acquire(hw); 2361 if (ret_val) 2362 goto out; 2363 2364 ret_val = e1000_read_phy_reg_mdic(hw, offset, data); 2365 2366 hw->phy.ops.release(hw); 2367 2368 out: 2369 return ret_val; 2370 } 2371 2372 /** 2373 * e1000_write_phy_reg_82580 - Write 82580 MDI control register 2374 * @hw: pointer to the HW structure 2375 * @offset: register offset to write to 2376 * @data: data to write to register at offset 2377 * 2378 * Writes data to MDI control register in the PHY at offset. 2379 **/ 2380 static s32 e1000_write_phy_reg_82580(struct e1000_hw *hw, u32 offset, u16 data) 2381 { 2382 s32 ret_val; 2383 2384 DEBUGFUNC("e1000_write_phy_reg_82580"); 2385 2386 ret_val = hw->phy.ops.acquire(hw); 2387 if (ret_val) 2388 goto out; 2389 2390 ret_val = e1000_write_phy_reg_mdic(hw, offset, data); 2391 2392 hw->phy.ops.release(hw); 2393 2394 out: 2395 return ret_val; 2396 } 2397 2398 /** 2399 * e1000_reset_mdicnfg_82580 - Reset MDICNFG destination and com_mdio bits 2400 * @hw: pointer to the HW structure 2401 * 2402 * This resets the the MDICNFG.Destination and MDICNFG.Com_MDIO bits based on 2403 * the values found in the EEPROM. This addresses an issue in which these 2404 * bits are not restored from EEPROM after reset. 2405 **/ 2406 static s32 e1000_reset_mdicnfg_82580(struct e1000_hw *hw) 2407 { 2408 s32 ret_val = E1000_SUCCESS; 2409 u32 mdicnfg; 2410 u16 nvm_data = 0; 2411 2412 DEBUGFUNC("e1000_reset_mdicnfg_82580"); 2413 2414 if (hw->mac.type != e1000_82580) 2415 goto out; 2416 if (!e1000_sgmii_active_82575(hw)) 2417 goto out; 2418 2419 ret_val = hw->nvm.ops.read(hw, NVM_INIT_CONTROL3_PORT_A + 2420 NVM_82580_LAN_FUNC_OFFSET(hw->bus.func), 1, 2421 &nvm_data); 2422 if (ret_val) { 2423 DEBUGOUT("NVM Read Error\n"); 2424 goto out; 2425 } 2426 2427 mdicnfg = E1000_READ_REG(hw, E1000_MDICNFG); 2428 if (nvm_data & NVM_WORD24_EXT_MDIO) 2429 mdicnfg |= E1000_MDICNFG_EXT_MDIO; 2430 if (nvm_data & NVM_WORD24_COM_MDIO) 2431 mdicnfg |= E1000_MDICNFG_COM_MDIO; 2432 E1000_WRITE_REG(hw, E1000_MDICNFG, mdicnfg); 2433 out: 2434 return ret_val; 2435 } 2436 2437 /** 2438 * e1000_reset_hw_82580 - Reset hardware 2439 * @hw: pointer to the HW structure 2440 * 2441 * This resets function or entire device (all ports, etc.) 2442 * to a known state. 2443 **/ 2444 static s32 e1000_reset_hw_82580(struct e1000_hw *hw) 2445 { 2446 s32 ret_val = E1000_SUCCESS; 2447 /* BH SW mailbox bit in SW_FW_SYNC */ 2448 u16 swmbsw_mask = E1000_SW_SYNCH_MB; 2449 u32 ctrl; 2450 bool global_device_reset = hw->dev_spec._82575.global_device_reset; 2451 2452 DEBUGFUNC("e1000_reset_hw_82580"); 2453 2454 hw->dev_spec._82575.global_device_reset = FALSE; 2455 2456 /* 82580 does not reliably do global_device_reset due to hw errata */ 2457 if (hw->mac.type == e1000_82580) 2458 global_device_reset = FALSE; 2459 2460 /* Get current control state. */ 2461 ctrl = E1000_READ_REG(hw, E1000_CTRL); 2462 2463 /* 2464 * Prevent the PCI-E bus from sticking if there is no TLP connection 2465 * on the last TLP read/write transaction when MAC is reset. 2466 */ 2467 ret_val = e1000_disable_pcie_master_generic(hw); 2468 if (ret_val) 2469 DEBUGOUT("PCI-E Master disable polling has failed.\n"); 2470 2471 DEBUGOUT("Masking off all interrupts\n"); 2472 E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); 2473 E1000_WRITE_REG(hw, E1000_RCTL, 0); 2474 E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); 2475 E1000_WRITE_FLUSH(hw); 2476 2477 msec_delay(10); 2478 2479 /* Determine whether or not a global dev reset is requested */ 2480 if (global_device_reset && hw->mac.ops.acquire_swfw_sync(hw, 2481 swmbsw_mask)) 2482 global_device_reset = FALSE; 2483 2484 if (global_device_reset && !(E1000_READ_REG(hw, E1000_STATUS) & 2485 E1000_STAT_DEV_RST_SET)) 2486 ctrl |= E1000_CTRL_DEV_RST; 2487 else 2488 ctrl |= E1000_CTRL_RST; 2489 2490 E1000_WRITE_REG(hw, E1000_CTRL, ctrl); 2491 2492 switch (hw->device_id) { 2493 case E1000_DEV_ID_DH89XXCC_SGMII: 2494 break; 2495 default: 2496 E1000_WRITE_FLUSH(hw); 2497 break; 2498 } 2499 2500 /* Add delay to insure DEV_RST or RST has time to complete */ 2501 msec_delay(5); 2502 2503 ret_val = e1000_get_auto_rd_done_generic(hw); 2504 if (ret_val) { 2505 /* 2506 * When auto config read does not complete, do not 2507 * return with an error. This can happen in situations 2508 * where there is no eeprom and prevents getting link. 2509 */ 2510 DEBUGOUT("Auto Read Done did not complete\n"); 2511 } 2512 2513 /* clear global device reset status bit */ 2514 E1000_WRITE_REG(hw, E1000_STATUS, E1000_STAT_DEV_RST_SET); 2515 2516 /* Clear any pending interrupt events. */ 2517 E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); 2518 E1000_READ_REG(hw, E1000_ICR); 2519 2520 ret_val = e1000_reset_mdicnfg_82580(hw); 2521 if (ret_val) 2522 DEBUGOUT("Could not reset MDICNFG based on EEPROM\n"); 2523 2524 /* Install any alternate MAC address into RAR0 */ 2525 ret_val = e1000_check_alt_mac_addr_generic(hw); 2526 2527 /* Release semaphore */ 2528 if (global_device_reset) 2529 hw->mac.ops.release_swfw_sync(hw, swmbsw_mask); 2530 2531 return ret_val; 2532 } 2533 2534 /** 2535 * e1000_rxpbs_adjust_82580 - adjust RXPBS value to reflect actual Rx PBA size 2536 * @data: data received by reading RXPBS register 2537 * 2538 * The 82580 uses a table based approach for packet buffer allocation sizes. 2539 * This function converts the retrieved value into the correct table value 2540 * 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 2541 * 0x0 36 72 144 1 2 4 8 16 2542 * 0x8 35 70 140 rsv rsv rsv rsv rsv 2543 */ 2544 u16 e1000_rxpbs_adjust_82580(u32 data) 2545 { 2546 u16 ret_val = 0; 2547 2548 if (data < E1000_82580_RXPBS_TABLE_SIZE) 2549 ret_val = e1000_82580_rxpbs_table[data]; 2550 2551 return ret_val; 2552 } 2553 2554 /** 2555 * e1000_validate_nvm_checksum_with_offset - Validate EEPROM 2556 * checksum 2557 * @hw: pointer to the HW structure 2558 * @offset: offset in words of the checksum protected region 2559 * 2560 * Calculates the EEPROM checksum by reading/adding each word of the EEPROM 2561 * and then verifies that the sum of the EEPROM is equal to 0xBABA. 2562 **/ 2563 s32 e1000_validate_nvm_checksum_with_offset(struct e1000_hw *hw, u16 offset) 2564 { 2565 s32 ret_val = E1000_SUCCESS; 2566 u16 checksum = 0; 2567 u16 i, nvm_data; 2568 2569 DEBUGFUNC("e1000_validate_nvm_checksum_with_offset"); 2570 2571 for (i = offset; i < ((NVM_CHECKSUM_REG + offset) + 1); i++) { 2572 ret_val = hw->nvm.ops.read(hw, i, 1, &nvm_data); 2573 if (ret_val) { 2574 DEBUGOUT("NVM Read Error\n"); 2575 goto out; 2576 } 2577 checksum += nvm_data; 2578 } 2579 2580 if (checksum != (u16) NVM_SUM) { 2581 DEBUGOUT("NVM Checksum Invalid\n"); 2582 ret_val = -E1000_ERR_NVM; 2583 goto out; 2584 } 2585 2586 out: 2587 return ret_val; 2588 } 2589 2590 /** 2591 * e1000_update_nvm_checksum_with_offset - Update EEPROM 2592 * checksum 2593 * @hw: pointer to the HW structure 2594 * @offset: offset in words of the checksum protected region 2595 * 2596 * Updates the EEPROM checksum by reading/adding each word of the EEPROM 2597 * up to the checksum. Then calculates the EEPROM checksum and writes the 2598 * value to the EEPROM. 2599 **/ 2600 s32 e1000_update_nvm_checksum_with_offset(struct e1000_hw *hw, u16 offset) 2601 { 2602 s32 ret_val; 2603 u16 checksum = 0; 2604 u16 i, nvm_data; 2605 2606 DEBUGFUNC("e1000_update_nvm_checksum_with_offset"); 2607 2608 for (i = offset; i < (NVM_CHECKSUM_REG + offset); i++) { 2609 ret_val = hw->nvm.ops.read(hw, i, 1, &nvm_data); 2610 if (ret_val) { 2611 DEBUGOUT("NVM Read Error while updating checksum.\n"); 2612 goto out; 2613 } 2614 checksum += nvm_data; 2615 } 2616 checksum = (u16) NVM_SUM - checksum; 2617 ret_val = hw->nvm.ops.write(hw, (NVM_CHECKSUM_REG + offset), 1, 2618 &checksum); 2619 if (ret_val) 2620 DEBUGOUT("NVM Write Error while updating checksum.\n"); 2621 2622 out: 2623 return ret_val; 2624 } 2625 2626 /** 2627 * e1000_validate_nvm_checksum_82580 - Validate EEPROM checksum 2628 * @hw: pointer to the HW structure 2629 * 2630 * Calculates the EEPROM section checksum by reading/adding each word of 2631 * the EEPROM and then verifies that the sum of the EEPROM is 2632 * equal to 0xBABA. 2633 **/ 2634 static s32 e1000_validate_nvm_checksum_82580(struct e1000_hw *hw) 2635 { 2636 s32 ret_val; 2637 u16 eeprom_regions_count = 1; 2638 u16 j, nvm_data; 2639 u16 nvm_offset; 2640 2641 DEBUGFUNC("e1000_validate_nvm_checksum_82580"); 2642 2643 ret_val = hw->nvm.ops.read(hw, NVM_COMPATIBILITY_REG_3, 1, &nvm_data); 2644 if (ret_val) { 2645 DEBUGOUT("NVM Read Error\n"); 2646 goto out; 2647 } 2648 2649 if (nvm_data & NVM_COMPATIBILITY_BIT_MASK) { 2650 /* if chekcsums compatibility bit is set validate checksums 2651 * for all 4 ports. */ 2652 eeprom_regions_count = 4; 2653 } 2654 2655 for (j = 0; j < eeprom_regions_count; j++) { 2656 nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j); 2657 ret_val = e1000_validate_nvm_checksum_with_offset(hw, 2658 nvm_offset); 2659 if (ret_val != E1000_SUCCESS) 2660 goto out; 2661 } 2662 2663 out: 2664 return ret_val; 2665 } 2666 2667 /** 2668 * e1000_update_nvm_checksum_82580 - Update EEPROM checksum 2669 * @hw: pointer to the HW structure 2670 * 2671 * Updates the EEPROM section checksums for all 4 ports by reading/adding 2672 * each word of the EEPROM up to the checksum. Then calculates the EEPROM 2673 * checksum and writes the value to the EEPROM. 2674 **/ 2675 static s32 e1000_update_nvm_checksum_82580(struct e1000_hw *hw) 2676 { 2677 s32 ret_val; 2678 u16 j, nvm_data; 2679 u16 nvm_offset; 2680 2681 DEBUGFUNC("e1000_update_nvm_checksum_82580"); 2682 2683 ret_val = hw->nvm.ops.read(hw, NVM_COMPATIBILITY_REG_3, 1, &nvm_data); 2684 if (ret_val) { 2685 DEBUGOUT("NVM Read Error while updating checksum compatibility bit.\n"); 2686 goto out; 2687 } 2688 2689 if (!(nvm_data & NVM_COMPATIBILITY_BIT_MASK)) { 2690 /* set compatibility bit to validate checksums appropriately */ 2691 nvm_data = nvm_data | NVM_COMPATIBILITY_BIT_MASK; 2692 ret_val = hw->nvm.ops.write(hw, NVM_COMPATIBILITY_REG_3, 1, 2693 &nvm_data); 2694 if (ret_val) { 2695 DEBUGOUT("NVM Write Error while updating checksum compatibility bit.\n"); 2696 goto out; 2697 } 2698 } 2699 2700 for (j = 0; j < 4; j++) { 2701 nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j); 2702 ret_val = e1000_update_nvm_checksum_with_offset(hw, nvm_offset); 2703 if (ret_val) 2704 goto out; 2705 } 2706 2707 out: 2708 return ret_val; 2709 } 2710 2711 /** 2712 * e1000_validate_nvm_checksum_i350 - Validate EEPROM checksum 2713 * @hw: pointer to the HW structure 2714 * 2715 * Calculates the EEPROM section checksum by reading/adding each word of 2716 * the EEPROM and then verifies that the sum of the EEPROM is 2717 * equal to 0xBABA. 2718 **/ 2719 static s32 e1000_validate_nvm_checksum_i350(struct e1000_hw *hw) 2720 { 2721 s32 ret_val = E1000_SUCCESS; 2722 u16 j; 2723 u16 nvm_offset; 2724 2725 DEBUGFUNC("e1000_validate_nvm_checksum_i350"); 2726 2727 for (j = 0; j < 4; j++) { 2728 nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j); 2729 ret_val = e1000_validate_nvm_checksum_with_offset(hw, 2730 nvm_offset); 2731 if (ret_val != E1000_SUCCESS) 2732 goto out; 2733 } 2734 2735 out: 2736 return ret_val; 2737 } 2738 2739 /** 2740 * e1000_update_nvm_checksum_i350 - Update EEPROM checksum 2741 * @hw: pointer to the HW structure 2742 * 2743 * Updates the EEPROM section checksums for all 4 ports by reading/adding 2744 * each word of the EEPROM up to the checksum. Then calculates the EEPROM 2745 * checksum and writes the value to the EEPROM. 2746 **/ 2747 static s32 e1000_update_nvm_checksum_i350(struct e1000_hw *hw) 2748 { 2749 s32 ret_val = E1000_SUCCESS; 2750 u16 j; 2751 u16 nvm_offset; 2752 2753 DEBUGFUNC("e1000_update_nvm_checksum_i350"); 2754 2755 for (j = 0; j < 4; j++) { 2756 nvm_offset = NVM_82580_LAN_FUNC_OFFSET(j); 2757 ret_val = e1000_update_nvm_checksum_with_offset(hw, nvm_offset); 2758 if (ret_val != E1000_SUCCESS) 2759 goto out; 2760 } 2761 2762 out: 2763 return ret_val; 2764 } 2765 2766 /** 2767 * __e1000_access_emi_reg - Read/write EMI register 2768 * @hw: pointer to the HW structure 2769 * @addr: EMI address to program 2770 * @data: pointer to value to read/write from/to the EMI address 2771 * @read: boolean flag to indicate read or write 2772 **/ 2773 static s32 __e1000_access_emi_reg(struct e1000_hw *hw, u16 address, 2774 u16 *data, bool read) 2775 { 2776 s32 ret_val; 2777 2778 DEBUGFUNC("__e1000_access_emi_reg"); 2779 2780 ret_val = hw->phy.ops.write_reg(hw, E1000_EMIADD, address); 2781 if (ret_val) 2782 return ret_val; 2783 2784 if (read) 2785 ret_val = hw->phy.ops.read_reg(hw, E1000_EMIDATA, data); 2786 else 2787 ret_val = hw->phy.ops.write_reg(hw, E1000_EMIDATA, *data); 2788 2789 return ret_val; 2790 } 2791 2792 /** 2793 * e1000_read_emi_reg - Read Extended Management Interface register 2794 * @hw: pointer to the HW structure 2795 * @addr: EMI address to program 2796 * @data: value to be read from the EMI address 2797 **/ 2798 s32 e1000_read_emi_reg(struct e1000_hw *hw, u16 addr, u16 *data) 2799 { 2800 DEBUGFUNC("e1000_read_emi_reg"); 2801 2802 return __e1000_access_emi_reg(hw, addr, data, TRUE); 2803 } 2804 2805 /** 2806 * e1000_initialize_M88E1512_phy - Initialize M88E1512 PHY 2807 * @hw: pointer to the HW structure 2808 * 2809 * Initialize Marverl 1512 to work correctly with Avoton. 2810 **/ 2811 s32 e1000_initialize_M88E1512_phy(struct e1000_hw *hw) 2812 { 2813 struct e1000_phy_info *phy = &hw->phy; 2814 s32 ret_val = E1000_SUCCESS; 2815 2816 DEBUGFUNC("e1000_initialize_M88E1512_phy"); 2817 2818 /* Check if this is correct PHY. */ 2819 if (phy->id != M88E1512_E_PHY_ID) 2820 goto out; 2821 2822 /* Switch to PHY page 0xFF. */ 2823 ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 0x00FF); 2824 if (ret_val) 2825 goto out; 2826 2827 ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_2, 0x214B); 2828 if (ret_val) 2829 goto out; 2830 2831 ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_1, 0x2144); 2832 if (ret_val) 2833 goto out; 2834 2835 ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_2, 0x0C28); 2836 if (ret_val) 2837 goto out; 2838 2839 ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_1, 0x2146); 2840 if (ret_val) 2841 goto out; 2842 2843 ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_2, 0xB233); 2844 if (ret_val) 2845 goto out; 2846 2847 ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_1, 0x214D); 2848 if (ret_val) 2849 goto out; 2850 2851 ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_2, 0xCC0C); 2852 if (ret_val) 2853 goto out; 2854 2855 ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_1, 0x2159); 2856 if (ret_val) 2857 goto out; 2858 2859 /* Switch to PHY page 0xFB. */ 2860 ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 0x00FB); 2861 if (ret_val) 2862 goto out; 2863 2864 ret_val = phy->ops.write_reg(hw, E1000_M88E1512_CFG_REG_3, 0x000D); 2865 if (ret_val) 2866 goto out; 2867 2868 /* Switch to PHY page 0x12. */ 2869 ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 0x12); 2870 if (ret_val) 2871 goto out; 2872 2873 /* Change mode to SGMII-to-Copper */ 2874 ret_val = phy->ops.write_reg(hw, E1000_M88E1512_MODE, 0x8001); 2875 if (ret_val) 2876 goto out; 2877 2878 /* Return the PHY to page 0. */ 2879 ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 0); 2880 if (ret_val) 2881 goto out; 2882 2883 ret_val = phy->ops.commit(hw); 2884 if (ret_val) { 2885 DEBUGOUT("Error committing the PHY changes\n"); 2886 return ret_val; 2887 } 2888 2889 msec_delay(1000); 2890 out: 2891 return ret_val; 2892 } 2893 2894 /** 2895 * e1000_set_eee_i350 - Enable/disable EEE support 2896 * @hw: pointer to the HW structure 2897 * 2898 * Enable/disable EEE based on setting in dev_spec structure. 2899 * 2900 **/ 2901 s32 e1000_set_eee_i350(struct e1000_hw *hw) 2902 { 2903 u32 ipcnfg, eeer; 2904 2905 DEBUGFUNC("e1000_set_eee_i350"); 2906 2907 if ((hw->mac.type < e1000_i350) || 2908 (hw->phy.media_type != e1000_media_type_copper)) 2909 goto out; 2910 ipcnfg = E1000_READ_REG(hw, E1000_IPCNFG); 2911 eeer = E1000_READ_REG(hw, E1000_EEER); 2912 2913 /* enable or disable per user setting */ 2914 if (!(hw->dev_spec._82575.eee_disable)) { 2915 u32 eee_su = E1000_READ_REG(hw, E1000_EEE_SU); 2916 2917 ipcnfg |= (E1000_IPCNFG_EEE_1G_AN | E1000_IPCNFG_EEE_100M_AN); 2918 eeer |= (E1000_EEER_TX_LPI_EN | E1000_EEER_RX_LPI_EN | 2919 E1000_EEER_LPI_FC); 2920 2921 /* This bit should not be set in normal operation. */ 2922 if (eee_su & E1000_EEE_SU_LPI_CLK_STP) 2923 DEBUGOUT("LPI Clock Stop Bit should not be set!\n"); 2924 } else { 2925 ipcnfg &= ~(E1000_IPCNFG_EEE_1G_AN | E1000_IPCNFG_EEE_100M_AN); 2926 eeer &= ~(E1000_EEER_TX_LPI_EN | E1000_EEER_RX_LPI_EN | 2927 E1000_EEER_LPI_FC); 2928 } 2929 E1000_WRITE_REG(hw, E1000_IPCNFG, ipcnfg); 2930 E1000_WRITE_REG(hw, E1000_EEER, eeer); 2931 E1000_READ_REG(hw, E1000_IPCNFG); 2932 E1000_READ_REG(hw, E1000_EEER); 2933 out: 2934 2935 return E1000_SUCCESS; 2936 } 2937 2938 /** 2939 * e1000_set_eee_i354 - Enable/disable EEE support 2940 * @hw: pointer to the HW structure 2941 * 2942 * Enable/disable EEE legacy mode based on setting in dev_spec structure. 2943 * 2944 **/ 2945 s32 e1000_set_eee_i354(struct e1000_hw *hw) 2946 { 2947 struct e1000_phy_info *phy = &hw->phy; 2948 s32 ret_val = E1000_SUCCESS; 2949 u16 phy_data; 2950 2951 DEBUGFUNC("e1000_set_eee_i354"); 2952 2953 if ((hw->phy.media_type != e1000_media_type_copper) || 2954 ((phy->id != M88E1543_E_PHY_ID) && 2955 (phy->id != M88E1512_E_PHY_ID))) 2956 goto out; 2957 2958 if (!hw->dev_spec._82575.eee_disable) { 2959 /* Switch to PHY page 18. */ 2960 ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 18); 2961 if (ret_val) 2962 goto out; 2963 2964 ret_val = phy->ops.read_reg(hw, E1000_M88E1543_EEE_CTRL_1, 2965 &phy_data); 2966 if (ret_val) 2967 goto out; 2968 2969 phy_data |= E1000_M88E1543_EEE_CTRL_1_MS; 2970 ret_val = phy->ops.write_reg(hw, E1000_M88E1543_EEE_CTRL_1, 2971 phy_data); 2972 if (ret_val) 2973 goto out; 2974 2975 /* Return the PHY to page 0. */ 2976 ret_val = phy->ops.write_reg(hw, E1000_M88E1543_PAGE_ADDR, 0); 2977 if (ret_val) 2978 goto out; 2979 2980 /* Turn on EEE advertisement. */ 2981 ret_val = e1000_read_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354, 2982 E1000_EEE_ADV_DEV_I354, 2983 &phy_data); 2984 if (ret_val) 2985 goto out; 2986 2987 phy_data |= E1000_EEE_ADV_100_SUPPORTED | 2988 E1000_EEE_ADV_1000_SUPPORTED; 2989 ret_val = e1000_write_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354, 2990 E1000_EEE_ADV_DEV_I354, 2991 phy_data); 2992 } else { 2993 /* Turn off EEE advertisement. */ 2994 ret_val = e1000_read_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354, 2995 E1000_EEE_ADV_DEV_I354, 2996 &phy_data); 2997 if (ret_val) 2998 goto out; 2999 3000 phy_data &= ~(E1000_EEE_ADV_100_SUPPORTED | 3001 E1000_EEE_ADV_1000_SUPPORTED); 3002 ret_val = e1000_write_xmdio_reg(hw, E1000_EEE_ADV_ADDR_I354, 3003 E1000_EEE_ADV_DEV_I354, 3004 phy_data); 3005 } 3006 3007 out: 3008 return ret_val; 3009 } 3010 3011 /** 3012 * e1000_get_eee_status_i354 - Get EEE status 3013 * @hw: pointer to the HW structure 3014 * @status: EEE status 3015 * 3016 * Get EEE status by guessing based on whether Tx or Rx LPI indications have 3017 * been received. 3018 **/ 3019 s32 e1000_get_eee_status_i354(struct e1000_hw *hw, bool *status) 3020 { 3021 struct e1000_phy_info *phy = &hw->phy; 3022 s32 ret_val = E1000_SUCCESS; 3023 u16 phy_data; 3024 3025 DEBUGFUNC("e1000_get_eee_status_i354"); 3026 3027 /* Check if EEE is supported on this device. */ 3028 if ((hw->phy.media_type != e1000_media_type_copper) || 3029 ((phy->id != M88E1543_E_PHY_ID) && 3030 (phy->id != M88E1512_E_PHY_ID))) 3031 goto out; 3032 3033 ret_val = e1000_read_xmdio_reg(hw, E1000_PCS_STATUS_ADDR_I354, 3034 E1000_PCS_STATUS_DEV_I354, 3035 &phy_data); 3036 if (ret_val) 3037 goto out; 3038 3039 *status = phy_data & (E1000_PCS_STATUS_TX_LPI_RCVD | 3040 E1000_PCS_STATUS_RX_LPI_RCVD) ? TRUE : FALSE; 3041 3042 out: 3043 return ret_val; 3044 } 3045 3046 /* Due to a hw errata, if the host tries to configure the VFTA register 3047 * while performing queries from the BMC or DMA, then the VFTA in some 3048 * cases won't be written. 3049 */ 3050 3051 /** 3052 * e1000_clear_vfta_i350 - Clear VLAN filter table 3053 * @hw: pointer to the HW structure 3054 * 3055 * Clears the register array which contains the VLAN filter table by 3056 * setting all the values to 0. 3057 **/ 3058 void e1000_clear_vfta_i350(struct e1000_hw *hw) 3059 { 3060 u32 offset; 3061 int i; 3062 3063 DEBUGFUNC("e1000_clear_vfta_350"); 3064 3065 for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { 3066 for (i = 0; i < 10; i++) 3067 E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, 0); 3068 3069 E1000_WRITE_FLUSH(hw); 3070 } 3071 } 3072 3073 /** 3074 * e1000_write_vfta_i350 - Write value to VLAN filter table 3075 * @hw: pointer to the HW structure 3076 * @offset: register offset in VLAN filter table 3077 * @value: register value written to VLAN filter table 3078 * 3079 * Writes value at the given offset in the register array which stores 3080 * the VLAN filter table. 3081 **/ 3082 void e1000_write_vfta_i350(struct e1000_hw *hw, u32 offset, u32 value) 3083 { 3084 int i; 3085 3086 DEBUGFUNC("e1000_write_vfta_350"); 3087 3088 for (i = 0; i < 10; i++) 3089 E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, value); 3090 3091 E1000_WRITE_FLUSH(hw); 3092 } 3093 3094 3095 /** 3096 * e1000_set_i2c_bb - Enable I2C bit-bang 3097 * @hw: pointer to the HW structure 3098 * 3099 * Enable I2C bit-bang interface 3100 * 3101 **/ 3102 s32 e1000_set_i2c_bb(struct e1000_hw *hw) 3103 { 3104 s32 ret_val = E1000_SUCCESS; 3105 u32 ctrl_ext, i2cparams; 3106 3107 DEBUGFUNC("e1000_set_i2c_bb"); 3108 3109 ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); 3110 ctrl_ext |= E1000_CTRL_I2C_ENA; 3111 E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); 3112 E1000_WRITE_FLUSH(hw); 3113 3114 i2cparams = E1000_READ_REG(hw, E1000_I2CPARAMS); 3115 i2cparams |= E1000_I2CBB_EN; 3116 i2cparams |= E1000_I2C_DATA_OE_N; 3117 i2cparams |= E1000_I2C_CLK_OE_N; 3118 E1000_WRITE_REG(hw, E1000_I2CPARAMS, i2cparams); 3119 E1000_WRITE_FLUSH(hw); 3120 3121 return ret_val; 3122 } 3123 3124 /** 3125 * e1000_read_i2c_byte_generic - Reads 8 bit word over I2C 3126 * @hw: pointer to hardware structure 3127 * @byte_offset: byte offset to read 3128 * @dev_addr: device address 3129 * @data: value read 3130 * 3131 * Performs byte read operation over I2C interface at 3132 * a specified device address. 3133 **/ 3134 s32 e1000_read_i2c_byte_generic(struct e1000_hw *hw, u8 byte_offset, 3135 u8 dev_addr, u8 *data) 3136 { 3137 s32 status = E1000_SUCCESS; 3138 u32 max_retry = 10; 3139 u32 retry = 1; 3140 u16 swfw_mask = 0; 3141 3142 bool nack = TRUE; 3143 3144 DEBUGFUNC("e1000_read_i2c_byte_generic"); 3145 3146 swfw_mask = E1000_SWFW_PHY0_SM; 3147 3148 do { 3149 if (hw->mac.ops.acquire_swfw_sync(hw, swfw_mask) 3150 != E1000_SUCCESS) { 3151 status = E1000_ERR_SWFW_SYNC; 3152 goto read_byte_out; 3153 } 3154 3155 e1000_i2c_start(hw); 3156 3157 /* Device Address and write indication */ 3158 status = e1000_clock_out_i2c_byte(hw, dev_addr); 3159 if (status != E1000_SUCCESS) 3160 goto fail; 3161 3162 status = e1000_get_i2c_ack(hw); 3163 if (status != E1000_SUCCESS) 3164 goto fail; 3165 3166 status = e1000_clock_out_i2c_byte(hw, byte_offset); 3167 if (status != E1000_SUCCESS) 3168 goto fail; 3169 3170 status = e1000_get_i2c_ack(hw); 3171 if (status != E1000_SUCCESS) 3172 goto fail; 3173 3174 e1000_i2c_start(hw); 3175 3176 /* Device Address and read indication */ 3177 status = e1000_clock_out_i2c_byte(hw, (dev_addr | 0x1)); 3178 if (status != E1000_SUCCESS) 3179 goto fail; 3180 3181 status = e1000_get_i2c_ack(hw); 3182 if (status != E1000_SUCCESS) 3183 goto fail; 3184 3185 status = e1000_clock_in_i2c_byte(hw, data); 3186 if (status != E1000_SUCCESS) 3187 goto fail; 3188 3189 status = e1000_clock_out_i2c_bit(hw, nack); 3190 if (status != E1000_SUCCESS) 3191 goto fail; 3192 3193 e1000_i2c_stop(hw); 3194 break; 3195 3196 fail: 3197 hw->mac.ops.release_swfw_sync(hw, swfw_mask); 3198 msec_delay(100); 3199 e1000_i2c_bus_clear(hw); 3200 retry++; 3201 if (retry < max_retry) 3202 DEBUGOUT("I2C byte read error - Retrying.\n"); 3203 else 3204 DEBUGOUT("I2C byte read error.\n"); 3205 3206 } while (retry < max_retry); 3207 3208 hw->mac.ops.release_swfw_sync(hw, swfw_mask); 3209 3210 read_byte_out: 3211 3212 return status; 3213 } 3214 3215 /** 3216 * e1000_write_i2c_byte_generic - Writes 8 bit word over I2C 3217 * @hw: pointer to hardware structure 3218 * @byte_offset: byte offset to write 3219 * @dev_addr: device address 3220 * @data: value to write 3221 * 3222 * Performs byte write operation over I2C interface at 3223 * a specified device address. 3224 **/ 3225 s32 e1000_write_i2c_byte_generic(struct e1000_hw *hw, u8 byte_offset, 3226 u8 dev_addr, u8 data) 3227 { 3228 s32 status = E1000_SUCCESS; 3229 u32 max_retry = 1; 3230 u32 retry = 0; 3231 u16 swfw_mask = 0; 3232 3233 DEBUGFUNC("e1000_write_i2c_byte_generic"); 3234 3235 swfw_mask = E1000_SWFW_PHY0_SM; 3236 3237 if (hw->mac.ops.acquire_swfw_sync(hw, swfw_mask) != E1000_SUCCESS) { 3238 status = E1000_ERR_SWFW_SYNC; 3239 goto write_byte_out; 3240 } 3241 3242 do { 3243 e1000_i2c_start(hw); 3244 3245 status = e1000_clock_out_i2c_byte(hw, dev_addr); 3246 if (status != E1000_SUCCESS) 3247 goto fail; 3248 3249 status = e1000_get_i2c_ack(hw); 3250 if (status != E1000_SUCCESS) 3251 goto fail; 3252 3253 status = e1000_clock_out_i2c_byte(hw, byte_offset); 3254 if (status != E1000_SUCCESS) 3255 goto fail; 3256 3257 status = e1000_get_i2c_ack(hw); 3258 if (status != E1000_SUCCESS) 3259 goto fail; 3260 3261 status = e1000_clock_out_i2c_byte(hw, data); 3262 if (status != E1000_SUCCESS) 3263 goto fail; 3264 3265 status = e1000_get_i2c_ack(hw); 3266 if (status != E1000_SUCCESS) 3267 goto fail; 3268 3269 e1000_i2c_stop(hw); 3270 break; 3271 3272 fail: 3273 e1000_i2c_bus_clear(hw); 3274 retry++; 3275 if (retry < max_retry) 3276 DEBUGOUT("I2C byte write error - Retrying.\n"); 3277 else 3278 DEBUGOUT("I2C byte write error.\n"); 3279 } while (retry < max_retry); 3280 3281 hw->mac.ops.release_swfw_sync(hw, swfw_mask); 3282 3283 write_byte_out: 3284 3285 return status; 3286 } 3287 3288 /** 3289 * e1000_i2c_start - Sets I2C start condition 3290 * @hw: pointer to hardware structure 3291 * 3292 * Sets I2C start condition (High -> Low on SDA while SCL is High) 3293 **/ 3294 static void e1000_i2c_start(struct e1000_hw *hw) 3295 { 3296 u32 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS); 3297 3298 DEBUGFUNC("e1000_i2c_start"); 3299 3300 /* Start condition must begin with data and clock high */ 3301 e1000_set_i2c_data(hw, &i2cctl, 1); 3302 e1000_raise_i2c_clk(hw, &i2cctl); 3303 3304 /* Setup time for start condition (4.7us) */ 3305 usec_delay(E1000_I2C_T_SU_STA); 3306 3307 e1000_set_i2c_data(hw, &i2cctl, 0); 3308 3309 /* Hold time for start condition (4us) */ 3310 usec_delay(E1000_I2C_T_HD_STA); 3311 3312 e1000_lower_i2c_clk(hw, &i2cctl); 3313 3314 /* Minimum low period of clock is 4.7 us */ 3315 usec_delay(E1000_I2C_T_LOW); 3316 3317 } 3318 3319 /** 3320 * e1000_i2c_stop - Sets I2C stop condition 3321 * @hw: pointer to hardware structure 3322 * 3323 * Sets I2C stop condition (Low -> High on SDA while SCL is High) 3324 **/ 3325 static void e1000_i2c_stop(struct e1000_hw *hw) 3326 { 3327 u32 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS); 3328 3329 DEBUGFUNC("e1000_i2c_stop"); 3330 3331 /* Stop condition must begin with data low and clock high */ 3332 e1000_set_i2c_data(hw, &i2cctl, 0); 3333 e1000_raise_i2c_clk(hw, &i2cctl); 3334 3335 /* Setup time for stop condition (4us) */ 3336 usec_delay(E1000_I2C_T_SU_STO); 3337 3338 e1000_set_i2c_data(hw, &i2cctl, 1); 3339 3340 /* bus free time between stop and start (4.7us)*/ 3341 usec_delay(E1000_I2C_T_BUF); 3342 } 3343 3344 /** 3345 * e1000_clock_in_i2c_byte - Clocks in one byte via I2C 3346 * @hw: pointer to hardware structure 3347 * @data: data byte to clock in 3348 * 3349 * Clocks in one byte data via I2C data/clock 3350 **/ 3351 static s32 e1000_clock_in_i2c_byte(struct e1000_hw *hw, u8 *data) 3352 { 3353 s32 i; 3354 bool bit = 0; 3355 3356 DEBUGFUNC("e1000_clock_in_i2c_byte"); 3357 3358 *data = 0; 3359 for (i = 7; i >= 0; i--) { 3360 e1000_clock_in_i2c_bit(hw, &bit); 3361 *data |= bit << i; 3362 } 3363 3364 return E1000_SUCCESS; 3365 } 3366 3367 /** 3368 * e1000_clock_out_i2c_byte - Clocks out one byte via I2C 3369 * @hw: pointer to hardware structure 3370 * @data: data byte clocked out 3371 * 3372 * Clocks out one byte data via I2C data/clock 3373 **/ 3374 static s32 e1000_clock_out_i2c_byte(struct e1000_hw *hw, u8 data) 3375 { 3376 s32 status = E1000_SUCCESS; 3377 s32 i; 3378 u32 i2cctl; 3379 bool bit = 0; 3380 3381 DEBUGFUNC("e1000_clock_out_i2c_byte"); 3382 3383 for (i = 7; i >= 0; i--) { 3384 bit = (data >> i) & 0x1; 3385 status = e1000_clock_out_i2c_bit(hw, bit); 3386 3387 if (status != E1000_SUCCESS) 3388 break; 3389 } 3390 3391 /* Release SDA line (set high) */ 3392 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS); 3393 3394 i2cctl |= E1000_I2C_DATA_OE_N; 3395 E1000_WRITE_REG(hw, E1000_I2CPARAMS, i2cctl); 3396 E1000_WRITE_FLUSH(hw); 3397 3398 return status; 3399 } 3400 3401 /** 3402 * e1000_get_i2c_ack - Polls for I2C ACK 3403 * @hw: pointer to hardware structure 3404 * 3405 * Clocks in/out one bit via I2C data/clock 3406 **/ 3407 static s32 e1000_get_i2c_ack(struct e1000_hw *hw) 3408 { 3409 s32 status = E1000_SUCCESS; 3410 u32 i = 0; 3411 u32 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS); 3412 u32 timeout = 10; 3413 bool ack = TRUE; 3414 3415 DEBUGFUNC("e1000_get_i2c_ack"); 3416 3417 e1000_raise_i2c_clk(hw, &i2cctl); 3418 3419 /* Minimum high period of clock is 4us */ 3420 usec_delay(E1000_I2C_T_HIGH); 3421 3422 /* Wait until SCL returns high */ 3423 for (i = 0; i < timeout; i++) { 3424 usec_delay(1); 3425 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS); 3426 if (i2cctl & E1000_I2C_CLK_IN) 3427 break; 3428 } 3429 if (!(i2cctl & E1000_I2C_CLK_IN)) 3430 return E1000_ERR_I2C; 3431 3432 ack = e1000_get_i2c_data(&i2cctl); 3433 if (ack) { 3434 DEBUGOUT("I2C ack was not received.\n"); 3435 status = E1000_ERR_I2C; 3436 } 3437 3438 e1000_lower_i2c_clk(hw, &i2cctl); 3439 3440 /* Minimum low period of clock is 4.7 us */ 3441 usec_delay(E1000_I2C_T_LOW); 3442 3443 return status; 3444 } 3445 3446 /** 3447 * e1000_clock_in_i2c_bit - Clocks in one bit via I2C data/clock 3448 * @hw: pointer to hardware structure 3449 * @data: read data value 3450 * 3451 * Clocks in one bit via I2C data/clock 3452 **/ 3453 static s32 e1000_clock_in_i2c_bit(struct e1000_hw *hw, bool *data) 3454 { 3455 u32 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS); 3456 3457 DEBUGFUNC("e1000_clock_in_i2c_bit"); 3458 3459 e1000_raise_i2c_clk(hw, &i2cctl); 3460 3461 /* Minimum high period of clock is 4us */ 3462 usec_delay(E1000_I2C_T_HIGH); 3463 3464 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS); 3465 *data = e1000_get_i2c_data(&i2cctl); 3466 3467 e1000_lower_i2c_clk(hw, &i2cctl); 3468 3469 /* Minimum low period of clock is 4.7 us */ 3470 usec_delay(E1000_I2C_T_LOW); 3471 3472 return E1000_SUCCESS; 3473 } 3474 3475 /** 3476 * e1000_clock_out_i2c_bit - Clocks in/out one bit via I2C data/clock 3477 * @hw: pointer to hardware structure 3478 * @data: data value to write 3479 * 3480 * Clocks out one bit via I2C data/clock 3481 **/ 3482 static s32 e1000_clock_out_i2c_bit(struct e1000_hw *hw, bool data) 3483 { 3484 s32 status; 3485 u32 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS); 3486 3487 DEBUGFUNC("e1000_clock_out_i2c_bit"); 3488 3489 status = e1000_set_i2c_data(hw, &i2cctl, data); 3490 if (status == E1000_SUCCESS) { 3491 e1000_raise_i2c_clk(hw, &i2cctl); 3492 3493 /* Minimum high period of clock is 4us */ 3494 usec_delay(E1000_I2C_T_HIGH); 3495 3496 e1000_lower_i2c_clk(hw, &i2cctl); 3497 3498 /* Minimum low period of clock is 4.7 us. 3499 * This also takes care of the data hold time. 3500 */ 3501 usec_delay(E1000_I2C_T_LOW); 3502 } else { 3503 status = E1000_ERR_I2C; 3504 DEBUGOUT1("I2C data was not set to %X\n", data); 3505 } 3506 3507 return status; 3508 } 3509 /** 3510 * e1000_raise_i2c_clk - Raises the I2C SCL clock 3511 * @hw: pointer to hardware structure 3512 * @i2cctl: Current value of I2CCTL register 3513 * 3514 * Raises the I2C clock line '0'->'1' 3515 **/ 3516 static void e1000_raise_i2c_clk(struct e1000_hw *hw, u32 *i2cctl) 3517 { 3518 DEBUGFUNC("e1000_raise_i2c_clk"); 3519 3520 *i2cctl |= E1000_I2C_CLK_OUT; 3521 *i2cctl &= ~E1000_I2C_CLK_OE_N; 3522 E1000_WRITE_REG(hw, E1000_I2CPARAMS, *i2cctl); 3523 E1000_WRITE_FLUSH(hw); 3524 3525 /* SCL rise time (1000ns) */ 3526 usec_delay(E1000_I2C_T_RISE); 3527 } 3528 3529 /** 3530 * e1000_lower_i2c_clk - Lowers the I2C SCL clock 3531 * @hw: pointer to hardware structure 3532 * @i2cctl: Current value of I2CCTL register 3533 * 3534 * Lowers the I2C clock line '1'->'0' 3535 **/ 3536 static void e1000_lower_i2c_clk(struct e1000_hw *hw, u32 *i2cctl) 3537 { 3538 3539 DEBUGFUNC("e1000_lower_i2c_clk"); 3540 3541 *i2cctl &= ~E1000_I2C_CLK_OUT; 3542 *i2cctl &= ~E1000_I2C_CLK_OE_N; 3543 E1000_WRITE_REG(hw, E1000_I2CPARAMS, *i2cctl); 3544 E1000_WRITE_FLUSH(hw); 3545 3546 /* SCL fall time (300ns) */ 3547 usec_delay(E1000_I2C_T_FALL); 3548 } 3549 3550 /** 3551 * e1000_set_i2c_data - Sets the I2C data bit 3552 * @hw: pointer to hardware structure 3553 * @i2cctl: Current value of I2CCTL register 3554 * @data: I2C data value (0 or 1) to set 3555 * 3556 * Sets the I2C data bit 3557 **/ 3558 static s32 e1000_set_i2c_data(struct e1000_hw *hw, u32 *i2cctl, bool data) 3559 { 3560 s32 status = E1000_SUCCESS; 3561 3562 DEBUGFUNC("e1000_set_i2c_data"); 3563 3564 if (data) 3565 *i2cctl |= E1000_I2C_DATA_OUT; 3566 else 3567 *i2cctl &= ~E1000_I2C_DATA_OUT; 3568 3569 *i2cctl &= ~E1000_I2C_DATA_OE_N; 3570 *i2cctl |= E1000_I2C_CLK_OE_N; 3571 E1000_WRITE_REG(hw, E1000_I2CPARAMS, *i2cctl); 3572 E1000_WRITE_FLUSH(hw); 3573 3574 /* Data rise/fall (1000ns/300ns) and set-up time (250ns) */ 3575 usec_delay(E1000_I2C_T_RISE + E1000_I2C_T_FALL + E1000_I2C_T_SU_DATA); 3576 3577 *i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS); 3578 if (data != e1000_get_i2c_data(i2cctl)) { 3579 status = E1000_ERR_I2C; 3580 DEBUGOUT1("Error - I2C data was not set to %X.\n", data); 3581 } 3582 3583 return status; 3584 } 3585 3586 /** 3587 * e1000_get_i2c_data - Reads the I2C SDA data bit 3588 * @hw: pointer to hardware structure 3589 * @i2cctl: Current value of I2CCTL register 3590 * 3591 * Returns the I2C data bit value 3592 **/ 3593 static bool e1000_get_i2c_data(u32 *i2cctl) 3594 { 3595 bool data; 3596 3597 DEBUGFUNC("e1000_get_i2c_data"); 3598 3599 if (*i2cctl & E1000_I2C_DATA_IN) 3600 data = 1; 3601 else 3602 data = 0; 3603 3604 return data; 3605 } 3606 3607 /** 3608 * e1000_i2c_bus_clear - Clears the I2C bus 3609 * @hw: pointer to hardware structure 3610 * 3611 * Clears the I2C bus by sending nine clock pulses. 3612 * Used when data line is stuck low. 3613 **/ 3614 void e1000_i2c_bus_clear(struct e1000_hw *hw) 3615 { 3616 u32 i2cctl = E1000_READ_REG(hw, E1000_I2CPARAMS); 3617 u32 i; 3618 3619 DEBUGFUNC("e1000_i2c_bus_clear"); 3620 3621 e1000_i2c_start(hw); 3622 3623 e1000_set_i2c_data(hw, &i2cctl, 1); 3624 3625 for (i = 0; i < 9; i++) { 3626 e1000_raise_i2c_clk(hw, &i2cctl); 3627 3628 /* Min high period of clock is 4us */ 3629 usec_delay(E1000_I2C_T_HIGH); 3630 3631 e1000_lower_i2c_clk(hw, &i2cctl); 3632 3633 /* Min low period of clock is 4.7us*/ 3634 usec_delay(E1000_I2C_T_LOW); 3635 } 3636 3637 e1000_i2c_start(hw); 3638 3639 /* Put the i2c bus back to default state */ 3640 e1000_i2c_stop(hw); 3641 } 3642 3643