1 /****************************************************************************** 2 3 Copyright (c) 2001-2015, Intel Corporation 4 All rights reserved. 5 6 Redistribution and use in source and binary forms, with or without 7 modification, are permitted provided that the following conditions are met: 8 9 1. Redistributions of source code must retain the above copyright notice, 10 this list of conditions and the following disclaimer. 11 12 2. Redistributions in binary form must reproduce the above copyright 13 notice, this list of conditions and the following disclaimer in the 14 documentation and/or other materials provided with the distribution. 15 16 3. Neither the name of the Intel Corporation nor the names of its 17 contributors may be used to endorse or promote products derived from 18 this software without specific prior written permission. 19 20 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 21 AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE 24 LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 30 POSSIBILITY OF SUCH DAMAGE. 31 32 ******************************************************************************/ 33 /*$FreeBSD$*/ 34 35 /* 36 * 82543GC Gigabit Ethernet Controller (Fiber) 37 * 82543GC Gigabit Ethernet Controller (Copper) 38 * 82544EI Gigabit Ethernet Controller (Copper) 39 * 82544EI Gigabit Ethernet Controller (Fiber) 40 * 82544GC Gigabit Ethernet Controller (Copper) 41 * 82544GC Gigabit Ethernet Controller (LOM) 42 */ 43 44 #include "e1000_api.h" 45 46 static s32 e1000_init_phy_params_82543(struct e1000_hw *hw); 47 static s32 e1000_init_nvm_params_82543(struct e1000_hw *hw); 48 static s32 e1000_init_mac_params_82543(struct e1000_hw *hw); 49 static s32 e1000_read_phy_reg_82543(struct e1000_hw *hw, u32 offset, 50 u16 *data); 51 static s32 e1000_write_phy_reg_82543(struct e1000_hw *hw, u32 offset, 52 u16 data); 53 static s32 e1000_phy_force_speed_duplex_82543(struct e1000_hw *hw); 54 static s32 e1000_phy_hw_reset_82543(struct e1000_hw *hw); 55 static s32 e1000_reset_hw_82543(struct e1000_hw *hw); 56 static s32 e1000_init_hw_82543(struct e1000_hw *hw); 57 static s32 e1000_setup_link_82543(struct e1000_hw *hw); 58 static s32 e1000_setup_copper_link_82543(struct e1000_hw *hw); 59 static s32 e1000_setup_fiber_link_82543(struct e1000_hw *hw); 60 static s32 e1000_check_for_copper_link_82543(struct e1000_hw *hw); 61 static s32 e1000_check_for_fiber_link_82543(struct e1000_hw *hw); 62 static s32 e1000_led_on_82543(struct e1000_hw *hw); 63 static s32 e1000_led_off_82543(struct e1000_hw *hw); 64 static void e1000_write_vfta_82543(struct e1000_hw *hw, u32 offset, 65 u32 value); 66 static void e1000_clear_hw_cntrs_82543(struct e1000_hw *hw); 67 static s32 e1000_config_mac_to_phy_82543(struct e1000_hw *hw); 68 static bool e1000_init_phy_disabled_82543(struct e1000_hw *hw); 69 static void e1000_lower_mdi_clk_82543(struct e1000_hw *hw, u32 *ctrl); 70 static s32 e1000_polarity_reversal_workaround_82543(struct e1000_hw *hw); 71 static void e1000_raise_mdi_clk_82543(struct e1000_hw *hw, u32 *ctrl); 72 static u16 e1000_shift_in_mdi_bits_82543(struct e1000_hw *hw); 73 static void e1000_shift_out_mdi_bits_82543(struct e1000_hw *hw, u32 data, 74 u16 count); 75 static bool e1000_tbi_compatibility_enabled_82543(struct e1000_hw *hw); 76 static void e1000_set_tbi_sbp_82543(struct e1000_hw *hw, bool state); 77 static s32 e1000_read_mac_addr_82543(struct e1000_hw *hw); 78 79 80 /** 81 * e1000_init_phy_params_82543 - Init PHY func ptrs. 82 * @hw: pointer to the HW structure 83 **/ 84 static s32 e1000_init_phy_params_82543(struct e1000_hw *hw) 85 { 86 struct e1000_phy_info *phy = &hw->phy; 87 s32 ret_val = E1000_SUCCESS; 88 89 DEBUGFUNC("e1000_init_phy_params_82543"); 90 91 if (hw->phy.media_type != e1000_media_type_copper) { 92 phy->type = e1000_phy_none; 93 goto out; 94 } else { 95 phy->ops.power_up = e1000_power_up_phy_copper; 96 phy->ops.power_down = e1000_power_down_phy_copper; 97 } 98 99 phy->addr = 1; 100 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; 101 phy->reset_delay_us = 10000; 102 phy->type = e1000_phy_m88; 103 104 /* Function Pointers */ 105 phy->ops.check_polarity = e1000_check_polarity_m88; 106 phy->ops.commit = e1000_phy_sw_reset_generic; 107 phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_82543; 108 phy->ops.get_cable_length = e1000_get_cable_length_m88; 109 phy->ops.get_cfg_done = e1000_get_cfg_done_generic; 110 phy->ops.read_reg = (hw->mac.type == e1000_82543) 111 ? e1000_read_phy_reg_82543 112 : e1000_read_phy_reg_m88; 113 phy->ops.reset = (hw->mac.type == e1000_82543) 114 ? e1000_phy_hw_reset_82543 115 : e1000_phy_hw_reset_generic; 116 phy->ops.write_reg = (hw->mac.type == e1000_82543) 117 ? e1000_write_phy_reg_82543 118 : e1000_write_phy_reg_m88; 119 phy->ops.get_info = e1000_get_phy_info_m88; 120 121 /* 122 * The external PHY of the 82543 can be in a funky state. 123 * Resetting helps us read the PHY registers for acquiring 124 * the PHY ID. 125 */ 126 if (!e1000_init_phy_disabled_82543(hw)) { 127 ret_val = phy->ops.reset(hw); 128 if (ret_val) { 129 DEBUGOUT("Resetting PHY during init failed.\n"); 130 goto out; 131 } 132 msec_delay(20); 133 } 134 135 ret_val = e1000_get_phy_id(hw); 136 if (ret_val) 137 goto out; 138 139 /* Verify phy id */ 140 switch (hw->mac.type) { 141 case e1000_82543: 142 if (phy->id != M88E1000_E_PHY_ID) { 143 ret_val = -E1000_ERR_PHY; 144 goto out; 145 } 146 break; 147 case e1000_82544: 148 if (phy->id != M88E1000_I_PHY_ID) { 149 ret_val = -E1000_ERR_PHY; 150 goto out; 151 } 152 break; 153 default: 154 ret_val = -E1000_ERR_PHY; 155 goto out; 156 break; 157 } 158 159 out: 160 return ret_val; 161 } 162 163 /** 164 * e1000_init_nvm_params_82543 - Init NVM func ptrs. 165 * @hw: pointer to the HW structure 166 **/ 167 static s32 e1000_init_nvm_params_82543(struct e1000_hw *hw) 168 { 169 struct e1000_nvm_info *nvm = &hw->nvm; 170 171 DEBUGFUNC("e1000_init_nvm_params_82543"); 172 173 nvm->type = e1000_nvm_eeprom_microwire; 174 nvm->word_size = 64; 175 nvm->delay_usec = 50; 176 nvm->address_bits = 6; 177 nvm->opcode_bits = 3; 178 179 /* Function Pointers */ 180 nvm->ops.read = e1000_read_nvm_microwire; 181 nvm->ops.update = e1000_update_nvm_checksum_generic; 182 nvm->ops.valid_led_default = e1000_valid_led_default_generic; 183 nvm->ops.validate = e1000_validate_nvm_checksum_generic; 184 nvm->ops.write = e1000_write_nvm_microwire; 185 186 return E1000_SUCCESS; 187 } 188 189 /** 190 * e1000_init_mac_params_82543 - Init MAC func ptrs. 191 * @hw: pointer to the HW structure 192 **/ 193 static s32 e1000_init_mac_params_82543(struct e1000_hw *hw) 194 { 195 struct e1000_mac_info *mac = &hw->mac; 196 197 DEBUGFUNC("e1000_init_mac_params_82543"); 198 199 /* Set media type */ 200 switch (hw->device_id) { 201 case E1000_DEV_ID_82543GC_FIBER: 202 case E1000_DEV_ID_82544EI_FIBER: 203 hw->phy.media_type = e1000_media_type_fiber; 204 break; 205 default: 206 hw->phy.media_type = e1000_media_type_copper; 207 break; 208 } 209 210 /* Set mta register count */ 211 mac->mta_reg_count = 128; 212 /* Set rar entry count */ 213 mac->rar_entry_count = E1000_RAR_ENTRIES; 214 215 /* Function pointers */ 216 217 /* bus type/speed/width */ 218 mac->ops.get_bus_info = e1000_get_bus_info_pci_generic; 219 /* function id */ 220 mac->ops.set_lan_id = e1000_set_lan_id_multi_port_pci; 221 /* reset */ 222 mac->ops.reset_hw = e1000_reset_hw_82543; 223 /* hw initialization */ 224 mac->ops.init_hw = e1000_init_hw_82543; 225 /* link setup */ 226 mac->ops.setup_link = e1000_setup_link_82543; 227 /* physical interface setup */ 228 mac->ops.setup_physical_interface = 229 (hw->phy.media_type == e1000_media_type_copper) 230 ? e1000_setup_copper_link_82543 : e1000_setup_fiber_link_82543; 231 /* check for link */ 232 mac->ops.check_for_link = 233 (hw->phy.media_type == e1000_media_type_copper) 234 ? e1000_check_for_copper_link_82543 235 : e1000_check_for_fiber_link_82543; 236 /* link info */ 237 mac->ops.get_link_up_info = 238 (hw->phy.media_type == e1000_media_type_copper) 239 ? e1000_get_speed_and_duplex_copper_generic 240 : e1000_get_speed_and_duplex_fiber_serdes_generic; 241 /* multicast address update */ 242 mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic; 243 /* writing VFTA */ 244 mac->ops.write_vfta = e1000_write_vfta_82543; 245 /* clearing VFTA */ 246 mac->ops.clear_vfta = e1000_clear_vfta_generic; 247 /* read mac address */ 248 mac->ops.read_mac_addr = e1000_read_mac_addr_82543; 249 /* turn on/off LED */ 250 mac->ops.led_on = e1000_led_on_82543; 251 mac->ops.led_off = e1000_led_off_82543; 252 /* clear hardware counters */ 253 mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_82543; 254 255 /* Set tbi compatibility */ 256 if ((hw->mac.type != e1000_82543) || 257 (hw->phy.media_type == e1000_media_type_fiber)) 258 e1000_set_tbi_compatibility_82543(hw, FALSE); 259 260 return E1000_SUCCESS; 261 } 262 263 /** 264 * e1000_init_function_pointers_82543 - Init func ptrs. 265 * @hw: pointer to the HW structure 266 * 267 * Called to initialize all function pointers and parameters. 268 **/ 269 void e1000_init_function_pointers_82543(struct e1000_hw *hw) 270 { 271 DEBUGFUNC("e1000_init_function_pointers_82543"); 272 273 hw->mac.ops.init_params = e1000_init_mac_params_82543; 274 hw->nvm.ops.init_params = e1000_init_nvm_params_82543; 275 hw->phy.ops.init_params = e1000_init_phy_params_82543; 276 } 277 278 /** 279 * e1000_tbi_compatibility_enabled_82543 - Returns TBI compat status 280 * @hw: pointer to the HW structure 281 * 282 * Returns the current status of 10-bit Interface (TBI) compatibility 283 * (enabled/disabled). 284 **/ 285 static bool e1000_tbi_compatibility_enabled_82543(struct e1000_hw *hw) 286 { 287 struct e1000_dev_spec_82543 *dev_spec = &hw->dev_spec._82543; 288 bool state = FALSE; 289 290 DEBUGFUNC("e1000_tbi_compatibility_enabled_82543"); 291 292 if (hw->mac.type != e1000_82543) { 293 DEBUGOUT("TBI compatibility workaround for 82543 only.\n"); 294 goto out; 295 } 296 297 state = !!(dev_spec->tbi_compatibility & TBI_COMPAT_ENABLED); 298 299 out: 300 return state; 301 } 302 303 /** 304 * e1000_set_tbi_compatibility_82543 - Set TBI compatibility 305 * @hw: pointer to the HW structure 306 * @state: enable/disable TBI compatibility 307 * 308 * Enables or disabled 10-bit Interface (TBI) compatibility. 309 **/ 310 void e1000_set_tbi_compatibility_82543(struct e1000_hw *hw, bool state) 311 { 312 struct e1000_dev_spec_82543 *dev_spec = &hw->dev_spec._82543; 313 314 DEBUGFUNC("e1000_set_tbi_compatibility_82543"); 315 316 if (hw->mac.type != e1000_82543) { 317 DEBUGOUT("TBI compatibility workaround for 82543 only.\n"); 318 goto out; 319 } 320 321 if (state) 322 dev_spec->tbi_compatibility |= TBI_COMPAT_ENABLED; 323 else 324 dev_spec->tbi_compatibility &= ~TBI_COMPAT_ENABLED; 325 326 out: 327 return; 328 } 329 330 /** 331 * e1000_tbi_sbp_enabled_82543 - Returns TBI SBP status 332 * @hw: pointer to the HW structure 333 * 334 * Returns the current status of 10-bit Interface (TBI) store bad packet (SBP) 335 * (enabled/disabled). 336 **/ 337 bool e1000_tbi_sbp_enabled_82543(struct e1000_hw *hw) 338 { 339 struct e1000_dev_spec_82543 *dev_spec = &hw->dev_spec._82543; 340 bool state = FALSE; 341 342 DEBUGFUNC("e1000_tbi_sbp_enabled_82543"); 343 344 if (hw->mac.type != e1000_82543) { 345 DEBUGOUT("TBI compatibility workaround for 82543 only.\n"); 346 goto out; 347 } 348 349 state = !!(dev_spec->tbi_compatibility & TBI_SBP_ENABLED); 350 351 out: 352 return state; 353 } 354 355 /** 356 * e1000_set_tbi_sbp_82543 - Set TBI SBP 357 * @hw: pointer to the HW structure 358 * @state: enable/disable TBI store bad packet 359 * 360 * Enables or disabled 10-bit Interface (TBI) store bad packet (SBP). 361 **/ 362 static void e1000_set_tbi_sbp_82543(struct e1000_hw *hw, bool state) 363 { 364 struct e1000_dev_spec_82543 *dev_spec = &hw->dev_spec._82543; 365 366 DEBUGFUNC("e1000_set_tbi_sbp_82543"); 367 368 if (state && e1000_tbi_compatibility_enabled_82543(hw)) 369 dev_spec->tbi_compatibility |= TBI_SBP_ENABLED; 370 else 371 dev_spec->tbi_compatibility &= ~TBI_SBP_ENABLED; 372 373 return; 374 } 375 376 /** 377 * e1000_init_phy_disabled_82543 - Returns init PHY status 378 * @hw: pointer to the HW structure 379 * 380 * Returns the current status of whether PHY initialization is disabled. 381 * True if PHY initialization is disabled else FALSE. 382 **/ 383 static bool e1000_init_phy_disabled_82543(struct e1000_hw *hw) 384 { 385 struct e1000_dev_spec_82543 *dev_spec = &hw->dev_spec._82543; 386 bool ret_val; 387 388 DEBUGFUNC("e1000_init_phy_disabled_82543"); 389 390 if (hw->mac.type != e1000_82543) { 391 ret_val = FALSE; 392 goto out; 393 } 394 395 ret_val = dev_spec->init_phy_disabled; 396 397 out: 398 return ret_val; 399 } 400 401 /** 402 * e1000_tbi_adjust_stats_82543 - Adjust stats when TBI enabled 403 * @hw: pointer to the HW structure 404 * @stats: Struct containing statistic register values 405 * @frame_len: The length of the frame in question 406 * @mac_addr: The Ethernet destination address of the frame in question 407 * @max_frame_size: The maximum frame size 408 * 409 * Adjusts the statistic counters when a frame is accepted by TBI_ACCEPT 410 **/ 411 void e1000_tbi_adjust_stats_82543(struct e1000_hw *hw, 412 struct e1000_hw_stats *stats, u32 frame_len, 413 u8 *mac_addr, u32 max_frame_size) 414 { 415 if (!(e1000_tbi_sbp_enabled_82543(hw))) 416 goto out; 417 418 /* First adjust the frame length. */ 419 frame_len--; 420 /* 421 * We need to adjust the statistics counters, since the hardware 422 * counters overcount this packet as a CRC error and undercount 423 * the packet as a good packet 424 */ 425 /* This packet should not be counted as a CRC error. */ 426 stats->crcerrs--; 427 /* This packet does count as a Good Packet Received. */ 428 stats->gprc++; 429 430 /* Adjust the Good Octets received counters */ 431 stats->gorc += frame_len; 432 433 /* 434 * Is this a broadcast or multicast? Check broadcast first, 435 * since the test for a multicast frame will test positive on 436 * a broadcast frame. 437 */ 438 if ((mac_addr[0] == 0xff) && (mac_addr[1] == 0xff)) 439 /* Broadcast packet */ 440 stats->bprc++; 441 else if (*mac_addr & 0x01) 442 /* Multicast packet */ 443 stats->mprc++; 444 445 /* 446 * In this case, the hardware has over counted the number of 447 * oversize frames. 448 */ 449 if ((frame_len == max_frame_size) && (stats->roc > 0)) 450 stats->roc--; 451 452 /* 453 * Adjust the bin counters when the extra byte put the frame in the 454 * wrong bin. Remember that the frame_len was adjusted above. 455 */ 456 if (frame_len == 64) { 457 stats->prc64++; 458 stats->prc127--; 459 } else if (frame_len == 127) { 460 stats->prc127++; 461 stats->prc255--; 462 } else if (frame_len == 255) { 463 stats->prc255++; 464 stats->prc511--; 465 } else if (frame_len == 511) { 466 stats->prc511++; 467 stats->prc1023--; 468 } else if (frame_len == 1023) { 469 stats->prc1023++; 470 stats->prc1522--; 471 } else if (frame_len == 1522) { 472 stats->prc1522++; 473 } 474 475 out: 476 return; 477 } 478 479 /** 480 * e1000_read_phy_reg_82543 - Read PHY register 481 * @hw: pointer to the HW structure 482 * @offset: register offset to be read 483 * @data: pointer to the read data 484 * 485 * Reads the PHY at offset and stores the information read to data. 486 **/ 487 static s32 e1000_read_phy_reg_82543(struct e1000_hw *hw, u32 offset, u16 *data) 488 { 489 u32 mdic; 490 s32 ret_val = E1000_SUCCESS; 491 492 DEBUGFUNC("e1000_read_phy_reg_82543"); 493 494 if (offset > MAX_PHY_REG_ADDRESS) { 495 DEBUGOUT1("PHY Address %d is out of range\n", offset); 496 ret_val = -E1000_ERR_PARAM; 497 goto out; 498 } 499 500 /* 501 * We must first send a preamble through the MDIO pin to signal the 502 * beginning of an MII instruction. This is done by sending 32 503 * consecutive "1" bits. 504 */ 505 e1000_shift_out_mdi_bits_82543(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); 506 507 /* 508 * Now combine the next few fields that are required for a read 509 * operation. We use this method instead of calling the 510 * e1000_shift_out_mdi_bits routine five different times. The format 511 * of an MII read instruction consists of a shift out of 14 bits and 512 * is defined as follows: 513 * <Preamble><SOF><Op Code><Phy Addr><Offset> 514 * followed by a shift in of 18 bits. This first two bits shifted in 515 * are TurnAround bits used to avoid contention on the MDIO pin when a 516 * READ operation is performed. These two bits are thrown away 517 * followed by a shift in of 16 bits which contains the desired data. 518 */ 519 mdic = (offset | (hw->phy.addr << 5) | 520 (PHY_OP_READ << 10) | (PHY_SOF << 12)); 521 522 e1000_shift_out_mdi_bits_82543(hw, mdic, 14); 523 524 /* 525 * Now that we've shifted out the read command to the MII, we need to 526 * "shift in" the 16-bit value (18 total bits) of the requested PHY 527 * register address. 528 */ 529 *data = e1000_shift_in_mdi_bits_82543(hw); 530 531 out: 532 return ret_val; 533 } 534 535 /** 536 * e1000_write_phy_reg_82543 - Write PHY register 537 * @hw: pointer to the HW structure 538 * @offset: register offset to be written 539 * @data: pointer to the data to be written at offset 540 * 541 * Writes data to the PHY at offset. 542 **/ 543 static s32 e1000_write_phy_reg_82543(struct e1000_hw *hw, u32 offset, u16 data) 544 { 545 u32 mdic; 546 s32 ret_val = E1000_SUCCESS; 547 548 DEBUGFUNC("e1000_write_phy_reg_82543"); 549 550 if (offset > MAX_PHY_REG_ADDRESS) { 551 DEBUGOUT1("PHY Address %d is out of range\n", offset); 552 ret_val = -E1000_ERR_PARAM; 553 goto out; 554 } 555 556 /* 557 * We'll need to use the SW defined pins to shift the write command 558 * out to the PHY. We first send a preamble to the PHY to signal the 559 * beginning of the MII instruction. This is done by sending 32 560 * consecutive "1" bits. 561 */ 562 e1000_shift_out_mdi_bits_82543(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); 563 564 /* 565 * Now combine the remaining required fields that will indicate a 566 * write operation. We use this method instead of calling the 567 * e1000_shift_out_mdi_bits routine for each field in the command. The 568 * format of a MII write instruction is as follows: 569 * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>. 570 */ 571 mdic = ((PHY_TURNAROUND) | (offset << 2) | (hw->phy.addr << 7) | 572 (PHY_OP_WRITE << 12) | (PHY_SOF << 14)); 573 mdic <<= 16; 574 mdic |= (u32)data; 575 576 e1000_shift_out_mdi_bits_82543(hw, mdic, 32); 577 578 out: 579 return ret_val; 580 } 581 582 /** 583 * e1000_raise_mdi_clk_82543 - Raise Management Data Input clock 584 * @hw: pointer to the HW structure 585 * @ctrl: pointer to the control register 586 * 587 * Raise the management data input clock by setting the MDC bit in the control 588 * register. 589 **/ 590 static void e1000_raise_mdi_clk_82543(struct e1000_hw *hw, u32 *ctrl) 591 { 592 /* 593 * Raise the clock input to the Management Data Clock (by setting the 594 * MDC bit), and then delay a sufficient amount of time. 595 */ 596 E1000_WRITE_REG(hw, E1000_CTRL, (*ctrl | E1000_CTRL_MDC)); 597 E1000_WRITE_FLUSH(hw); 598 usec_delay(10); 599 } 600 601 /** 602 * e1000_lower_mdi_clk_82543 - Lower Management Data Input clock 603 * @hw: pointer to the HW structure 604 * @ctrl: pointer to the control register 605 * 606 * Lower the management data input clock by clearing the MDC bit in the 607 * control register. 608 **/ 609 static void e1000_lower_mdi_clk_82543(struct e1000_hw *hw, u32 *ctrl) 610 { 611 /* 612 * Lower the clock input to the Management Data Clock (by clearing the 613 * MDC bit), and then delay a sufficient amount of time. 614 */ 615 E1000_WRITE_REG(hw, E1000_CTRL, (*ctrl & ~E1000_CTRL_MDC)); 616 E1000_WRITE_FLUSH(hw); 617 usec_delay(10); 618 } 619 620 /** 621 * e1000_shift_out_mdi_bits_82543 - Shift data bits our to the PHY 622 * @hw: pointer to the HW structure 623 * @data: data to send to the PHY 624 * @count: number of bits to shift out 625 * 626 * We need to shift 'count' bits out to the PHY. So, the value in the 627 * "data" parameter will be shifted out to the PHY one bit at a time. 628 * In order to do this, "data" must be broken down into bits. 629 **/ 630 static void e1000_shift_out_mdi_bits_82543(struct e1000_hw *hw, u32 data, 631 u16 count) 632 { 633 u32 ctrl, mask; 634 635 /* 636 * We need to shift "count" number of bits out to the PHY. So, the 637 * value in the "data" parameter will be shifted out to the PHY one 638 * bit at a time. In order to do this, "data" must be broken down 639 * into bits. 640 */ 641 mask = 0x01; 642 mask <<= (count - 1); 643 644 ctrl = E1000_READ_REG(hw, E1000_CTRL); 645 646 /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */ 647 ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR); 648 649 while (mask) { 650 /* 651 * A "1" is shifted out to the PHY by setting the MDIO bit to 652 * "1" and then raising and lowering the Management Data Clock. 653 * A "0" is shifted out to the PHY by setting the MDIO bit to 654 * "0" and then raising and lowering the clock. 655 */ 656 if (data & mask) 657 ctrl |= E1000_CTRL_MDIO; 658 else 659 ctrl &= ~E1000_CTRL_MDIO; 660 661 E1000_WRITE_REG(hw, E1000_CTRL, ctrl); 662 E1000_WRITE_FLUSH(hw); 663 664 usec_delay(10); 665 666 e1000_raise_mdi_clk_82543(hw, &ctrl); 667 e1000_lower_mdi_clk_82543(hw, &ctrl); 668 669 mask >>= 1; 670 } 671 } 672 673 /** 674 * e1000_shift_in_mdi_bits_82543 - Shift data bits in from the PHY 675 * @hw: pointer to the HW structure 676 * 677 * In order to read a register from the PHY, we need to shift 18 bits 678 * in from the PHY. Bits are "shifted in" by raising the clock input to 679 * the PHY (setting the MDC bit), and then reading the value of the data out 680 * MDIO bit. 681 **/ 682 static u16 e1000_shift_in_mdi_bits_82543(struct e1000_hw *hw) 683 { 684 u32 ctrl; 685 u16 data = 0; 686 u8 i; 687 688 /* 689 * In order to read a register from the PHY, we need to shift in a 690 * total of 18 bits from the PHY. The first two bit (turnaround) 691 * times are used to avoid contention on the MDIO pin when a read 692 * operation is performed. These two bits are ignored by us and 693 * thrown away. Bits are "shifted in" by raising the input to the 694 * Management Data Clock (setting the MDC bit) and then reading the 695 * value of the MDIO bit. 696 */ 697 ctrl = E1000_READ_REG(hw, E1000_CTRL); 698 699 /* 700 * Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as 701 * input. 702 */ 703 ctrl &= ~E1000_CTRL_MDIO_DIR; 704 ctrl &= ~E1000_CTRL_MDIO; 705 706 E1000_WRITE_REG(hw, E1000_CTRL, ctrl); 707 E1000_WRITE_FLUSH(hw); 708 709 /* 710 * Raise and lower the clock before reading in the data. This accounts 711 * for the turnaround bits. The first clock occurred when we clocked 712 * out the last bit of the Register Address. 713 */ 714 e1000_raise_mdi_clk_82543(hw, &ctrl); 715 e1000_lower_mdi_clk_82543(hw, &ctrl); 716 717 for (data = 0, i = 0; i < 16; i++) { 718 data <<= 1; 719 e1000_raise_mdi_clk_82543(hw, &ctrl); 720 ctrl = E1000_READ_REG(hw, E1000_CTRL); 721 /* Check to see if we shifted in a "1". */ 722 if (ctrl & E1000_CTRL_MDIO) 723 data |= 1; 724 e1000_lower_mdi_clk_82543(hw, &ctrl); 725 } 726 727 e1000_raise_mdi_clk_82543(hw, &ctrl); 728 e1000_lower_mdi_clk_82543(hw, &ctrl); 729 730 return data; 731 } 732 733 /** 734 * e1000_phy_force_speed_duplex_82543 - Force speed/duplex for PHY 735 * @hw: pointer to the HW structure 736 * 737 * Calls the function to force speed and duplex for the m88 PHY, and 738 * if the PHY is not auto-negotiating and the speed is forced to 10Mbit, 739 * then call the function for polarity reversal workaround. 740 **/ 741 static s32 e1000_phy_force_speed_duplex_82543(struct e1000_hw *hw) 742 { 743 s32 ret_val; 744 745 DEBUGFUNC("e1000_phy_force_speed_duplex_82543"); 746 747 ret_val = e1000_phy_force_speed_duplex_m88(hw); 748 if (ret_val) 749 goto out; 750 751 if (!hw->mac.autoneg && (hw->mac.forced_speed_duplex & 752 E1000_ALL_10_SPEED)) 753 ret_val = e1000_polarity_reversal_workaround_82543(hw); 754 755 out: 756 return ret_val; 757 } 758 759 /** 760 * e1000_polarity_reversal_workaround_82543 - Workaround polarity reversal 761 * @hw: pointer to the HW structure 762 * 763 * When forcing link to 10 Full or 10 Half, the PHY can reverse the polarity 764 * inadvertently. To workaround the issue, we disable the transmitter on 765 * the PHY until we have established the link partner's link parameters. 766 **/ 767 static s32 e1000_polarity_reversal_workaround_82543(struct e1000_hw *hw) 768 { 769 s32 ret_val = E1000_SUCCESS; 770 u16 mii_status_reg; 771 u16 i; 772 bool link; 773 774 if (!(hw->phy.ops.write_reg)) 775 goto out; 776 777 /* Polarity reversal workaround for forced 10F/10H links. */ 778 779 /* Disable the transmitter on the PHY */ 780 781 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019); 782 if (ret_val) 783 goto out; 784 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFFF); 785 if (ret_val) 786 goto out; 787 788 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000); 789 if (ret_val) 790 goto out; 791 792 /* 793 * This loop will early-out if the NO link condition has been met. 794 * In other words, DO NOT use e1000_phy_has_link_generic() here. 795 */ 796 for (i = PHY_FORCE_TIME; i > 0; i--) { 797 /* 798 * Read the MII Status Register and wait for Link Status bit 799 * to be clear. 800 */ 801 802 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &mii_status_reg); 803 if (ret_val) 804 goto out; 805 806 ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &mii_status_reg); 807 if (ret_val) 808 goto out; 809 810 if (!(mii_status_reg & ~MII_SR_LINK_STATUS)) 811 break; 812 msec_delay_irq(100); 813 } 814 815 /* Recommended delay time after link has been lost */ 816 msec_delay_irq(1000); 817 818 /* Now we will re-enable the transmitter on the PHY */ 819 820 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019); 821 if (ret_val) 822 goto out; 823 msec_delay_irq(50); 824 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFF0); 825 if (ret_val) 826 goto out; 827 msec_delay_irq(50); 828 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFF00); 829 if (ret_val) 830 goto out; 831 msec_delay_irq(50); 832 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x0000); 833 if (ret_val) 834 goto out; 835 836 ret_val = hw->phy.ops.write_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000); 837 if (ret_val) 838 goto out; 839 840 /* 841 * Read the MII Status Register and wait for Link Status bit 842 * to be set. 843 */ 844 ret_val = e1000_phy_has_link_generic(hw, PHY_FORCE_TIME, 100000, &link); 845 if (ret_val) 846 goto out; 847 848 out: 849 return ret_val; 850 } 851 852 /** 853 * e1000_phy_hw_reset_82543 - PHY hardware reset 854 * @hw: pointer to the HW structure 855 * 856 * Sets the PHY_RESET_DIR bit in the extended device control register 857 * to put the PHY into a reset and waits for completion. Once the reset 858 * has been accomplished, clear the PHY_RESET_DIR bit to take the PHY out 859 * of reset. 860 **/ 861 static s32 e1000_phy_hw_reset_82543(struct e1000_hw *hw) 862 { 863 u32 ctrl_ext; 864 s32 ret_val; 865 866 DEBUGFUNC("e1000_phy_hw_reset_82543"); 867 868 /* 869 * Read the Extended Device Control Register, assert the PHY_RESET_DIR 870 * bit to put the PHY into reset... 871 */ 872 ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); 873 ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR; 874 ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA; 875 E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); 876 E1000_WRITE_FLUSH(hw); 877 878 msec_delay(10); 879 880 /* ...then take it out of reset. */ 881 ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA; 882 E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); 883 E1000_WRITE_FLUSH(hw); 884 885 usec_delay(150); 886 887 if (!(hw->phy.ops.get_cfg_done)) 888 return E1000_SUCCESS; 889 890 ret_val = hw->phy.ops.get_cfg_done(hw); 891 892 return ret_val; 893 } 894 895 /** 896 * e1000_reset_hw_82543 - Reset hardware 897 * @hw: pointer to the HW structure 898 * 899 * This resets the hardware into a known state. 900 **/ 901 static s32 e1000_reset_hw_82543(struct e1000_hw *hw) 902 { 903 u32 ctrl, icr; 904 s32 ret_val = E1000_SUCCESS; 905 906 DEBUGFUNC("e1000_reset_hw_82543"); 907 908 DEBUGOUT("Masking off all interrupts\n"); 909 E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); 910 911 E1000_WRITE_REG(hw, E1000_RCTL, 0); 912 E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); 913 E1000_WRITE_FLUSH(hw); 914 915 e1000_set_tbi_sbp_82543(hw, FALSE); 916 917 /* 918 * Delay to allow any outstanding PCI transactions to complete before 919 * resetting the device 920 */ 921 msec_delay(10); 922 923 ctrl = E1000_READ_REG(hw, E1000_CTRL); 924 925 DEBUGOUT("Issuing a global reset to 82543/82544 MAC\n"); 926 if (hw->mac.type == e1000_82543) { 927 E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); 928 } else { 929 /* 930 * The 82544 can't ACK the 64-bit write when issuing the 931 * reset, so use IO-mapping as a workaround. 932 */ 933 E1000_WRITE_REG_IO(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); 934 } 935 936 /* 937 * After MAC reset, force reload of NVM to restore power-on 938 * settings to device. 939 */ 940 hw->nvm.ops.reload(hw); 941 msec_delay(2); 942 943 /* Masking off and clearing any pending interrupts */ 944 E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); 945 icr = E1000_READ_REG(hw, E1000_ICR); 946 947 return ret_val; 948 } 949 950 /** 951 * e1000_init_hw_82543 - Initialize hardware 952 * @hw: pointer to the HW structure 953 * 954 * This inits the hardware readying it for operation. 955 **/ 956 static s32 e1000_init_hw_82543(struct e1000_hw *hw) 957 { 958 struct e1000_mac_info *mac = &hw->mac; 959 struct e1000_dev_spec_82543 *dev_spec = &hw->dev_spec._82543; 960 u32 ctrl; 961 s32 ret_val; 962 u16 i; 963 964 DEBUGFUNC("e1000_init_hw_82543"); 965 966 /* Disabling VLAN filtering */ 967 E1000_WRITE_REG(hw, E1000_VET, 0); 968 mac->ops.clear_vfta(hw); 969 970 /* Setup the receive address. */ 971 e1000_init_rx_addrs_generic(hw, mac->rar_entry_count); 972 973 /* Zero out the Multicast HASH table */ 974 DEBUGOUT("Zeroing the MTA\n"); 975 for (i = 0; i < mac->mta_reg_count; i++) { 976 E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); 977 E1000_WRITE_FLUSH(hw); 978 } 979 980 /* 981 * Set the PCI priority bit correctly in the CTRL register. This 982 * determines if the adapter gives priority to receives, or if it 983 * gives equal priority to transmits and receives. 984 */ 985 if (hw->mac.type == e1000_82543 && dev_spec->dma_fairness) { 986 ctrl = E1000_READ_REG(hw, E1000_CTRL); 987 E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_PRIOR); 988 } 989 990 e1000_pcix_mmrbc_workaround_generic(hw); 991 992 /* Setup link and flow control */ 993 ret_val = mac->ops.setup_link(hw); 994 995 /* 996 * Clear all of the statistics registers (clear on read). It is 997 * important that we do this after we have tried to establish link 998 * because the symbol error count will increment wildly if there 999 * is no link. 1000 */ 1001 e1000_clear_hw_cntrs_82543(hw); 1002 1003 return ret_val; 1004 } 1005 1006 /** 1007 * e1000_setup_link_82543 - Setup flow control and link settings 1008 * @hw: pointer to the HW structure 1009 * 1010 * Read the EEPROM to determine the initial polarity value and write the 1011 * extended device control register with the information before calling 1012 * the generic setup link function, which does the following: 1013 * Determines which flow control settings to use, then configures flow 1014 * control. Calls the appropriate media-specific link configuration 1015 * function. Assuming the adapter has a valid link partner, a valid link 1016 * should be established. Assumes the hardware has previously been reset 1017 * and the transmitter and receiver are not enabled. 1018 **/ 1019 static s32 e1000_setup_link_82543(struct e1000_hw *hw) 1020 { 1021 u32 ctrl_ext; 1022 s32 ret_val; 1023 u16 data; 1024 1025 DEBUGFUNC("e1000_setup_link_82543"); 1026 1027 /* 1028 * Take the 4 bits from NVM word 0xF that determine the initial 1029 * polarity value for the SW controlled pins, and setup the 1030 * Extended Device Control reg with that info. 1031 * This is needed because one of the SW controlled pins is used for 1032 * signal detection. So this should be done before phy setup. 1033 */ 1034 if (hw->mac.type == e1000_82543) { 1035 ret_val = hw->nvm.ops.read(hw, NVM_INIT_CONTROL2_REG, 1, &data); 1036 if (ret_val) { 1037 DEBUGOUT("NVM Read Error\n"); 1038 ret_val = -E1000_ERR_NVM; 1039 goto out; 1040 } 1041 ctrl_ext = ((data & NVM_WORD0F_SWPDIO_EXT_MASK) << 1042 NVM_SWDPIO_EXT_SHIFT); 1043 E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); 1044 } 1045 1046 ret_val = e1000_setup_link_generic(hw); 1047 1048 out: 1049 return ret_val; 1050 } 1051 1052 /** 1053 * e1000_setup_copper_link_82543 - Configure copper link settings 1054 * @hw: pointer to the HW structure 1055 * 1056 * Configures the link for auto-neg or forced speed and duplex. Then we check 1057 * for link, once link is established calls to configure collision distance 1058 * and flow control are called. 1059 **/ 1060 static s32 e1000_setup_copper_link_82543(struct e1000_hw *hw) 1061 { 1062 u32 ctrl; 1063 s32 ret_val; 1064 bool link; 1065 1066 DEBUGFUNC("e1000_setup_copper_link_82543"); 1067 1068 ctrl = E1000_READ_REG(hw, E1000_CTRL) | E1000_CTRL_SLU; 1069 /* 1070 * With 82543, we need to force speed and duplex on the MAC 1071 * equal to what the PHY speed and duplex configuration is. 1072 * In addition, we need to perform a hardware reset on the 1073 * PHY to take it out of reset. 1074 */ 1075 if (hw->mac.type == e1000_82543) { 1076 ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 1077 E1000_WRITE_REG(hw, E1000_CTRL, ctrl); 1078 ret_val = hw->phy.ops.reset(hw); 1079 if (ret_val) 1080 goto out; 1081 } else { 1082 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 1083 E1000_WRITE_REG(hw, E1000_CTRL, ctrl); 1084 } 1085 1086 /* Set MDI/MDI-X, Polarity Reversal, and downshift settings */ 1087 ret_val = e1000_copper_link_setup_m88(hw); 1088 if (ret_val) 1089 goto out; 1090 1091 if (hw->mac.autoneg) { 1092 /* 1093 * Setup autoneg and flow control advertisement and perform 1094 * autonegotiation. 1095 */ 1096 ret_val = e1000_copper_link_autoneg(hw); 1097 if (ret_val) 1098 goto out; 1099 } else { 1100 /* 1101 * PHY will be set to 10H, 10F, 100H or 100F 1102 * depending on user settings. 1103 */ 1104 DEBUGOUT("Forcing Speed and Duplex\n"); 1105 ret_val = e1000_phy_force_speed_duplex_82543(hw); 1106 if (ret_val) { 1107 DEBUGOUT("Error Forcing Speed and Duplex\n"); 1108 goto out; 1109 } 1110 } 1111 1112 /* 1113 * Check link status. Wait up to 100 microseconds for link to become 1114 * valid. 1115 */ 1116 ret_val = e1000_phy_has_link_generic(hw, COPPER_LINK_UP_LIMIT, 10, 1117 &link); 1118 if (ret_val) 1119 goto out; 1120 1121 1122 if (link) { 1123 DEBUGOUT("Valid link established!!!\n"); 1124 /* Config the MAC and PHY after link is up */ 1125 if (hw->mac.type == e1000_82544) { 1126 hw->mac.ops.config_collision_dist(hw); 1127 } else { 1128 ret_val = e1000_config_mac_to_phy_82543(hw); 1129 if (ret_val) 1130 goto out; 1131 } 1132 ret_val = e1000_config_fc_after_link_up_generic(hw); 1133 } else { 1134 DEBUGOUT("Unable to establish link!!!\n"); 1135 } 1136 1137 out: 1138 return ret_val; 1139 } 1140 1141 /** 1142 * e1000_setup_fiber_link_82543 - Setup link for fiber 1143 * @hw: pointer to the HW structure 1144 * 1145 * Configures collision distance and flow control for fiber links. Upon 1146 * successful setup, poll for link. 1147 **/ 1148 static s32 e1000_setup_fiber_link_82543(struct e1000_hw *hw) 1149 { 1150 u32 ctrl; 1151 s32 ret_val; 1152 1153 DEBUGFUNC("e1000_setup_fiber_link_82543"); 1154 1155 ctrl = E1000_READ_REG(hw, E1000_CTRL); 1156 1157 /* Take the link out of reset */ 1158 ctrl &= ~E1000_CTRL_LRST; 1159 1160 hw->mac.ops.config_collision_dist(hw); 1161 1162 ret_val = e1000_commit_fc_settings_generic(hw); 1163 if (ret_val) 1164 goto out; 1165 1166 DEBUGOUT("Auto-negotiation enabled\n"); 1167 1168 E1000_WRITE_REG(hw, E1000_CTRL, ctrl); 1169 E1000_WRITE_FLUSH(hw); 1170 msec_delay(1); 1171 1172 /* 1173 * For these adapters, the SW definable pin 1 is cleared when the 1174 * optics detect a signal. If we have a signal, then poll for a 1175 * "Link-Up" indication. 1176 */ 1177 if (!(E1000_READ_REG(hw, E1000_CTRL) & E1000_CTRL_SWDPIN1)) 1178 ret_val = e1000_poll_fiber_serdes_link_generic(hw); 1179 else 1180 DEBUGOUT("No signal detected\n"); 1181 1182 out: 1183 return ret_val; 1184 } 1185 1186 /** 1187 * e1000_check_for_copper_link_82543 - Check for link (Copper) 1188 * @hw: pointer to the HW structure 1189 * 1190 * Checks the phy for link, if link exists, do the following: 1191 * - check for downshift 1192 * - do polarity workaround (if necessary) 1193 * - configure collision distance 1194 * - configure flow control after link up 1195 * - configure tbi compatibility 1196 **/ 1197 static s32 e1000_check_for_copper_link_82543(struct e1000_hw *hw) 1198 { 1199 struct e1000_mac_info *mac = &hw->mac; 1200 u32 icr, rctl; 1201 s32 ret_val; 1202 u16 speed, duplex; 1203 bool link; 1204 1205 DEBUGFUNC("e1000_check_for_copper_link_82543"); 1206 1207 if (!mac->get_link_status) { 1208 ret_val = E1000_SUCCESS; 1209 goto out; 1210 } 1211 1212 ret_val = e1000_phy_has_link_generic(hw, 1, 0, &link); 1213 if (ret_val) 1214 goto out; 1215 1216 if (!link) 1217 goto out; /* No link detected */ 1218 1219 mac->get_link_status = FALSE; 1220 1221 e1000_check_downshift_generic(hw); 1222 1223 /* 1224 * If we are forcing speed/duplex, then we can return since 1225 * we have already determined whether we have link or not. 1226 */ 1227 if (!mac->autoneg) { 1228 /* 1229 * If speed and duplex are forced to 10H or 10F, then we will 1230 * implement the polarity reversal workaround. We disable 1231 * interrupts first, and upon returning, place the devices 1232 * interrupt state to its previous value except for the link 1233 * status change interrupt which will happened due to the 1234 * execution of this workaround. 1235 */ 1236 if (mac->forced_speed_duplex & E1000_ALL_10_SPEED) { 1237 E1000_WRITE_REG(hw, E1000_IMC, 0xFFFFFFFF); 1238 ret_val = e1000_polarity_reversal_workaround_82543(hw); 1239 icr = E1000_READ_REG(hw, E1000_ICR); 1240 E1000_WRITE_REG(hw, E1000_ICS, (icr & ~E1000_ICS_LSC)); 1241 E1000_WRITE_REG(hw, E1000_IMS, IMS_ENABLE_MASK); 1242 } 1243 1244 ret_val = -E1000_ERR_CONFIG; 1245 goto out; 1246 } 1247 1248 /* 1249 * We have a M88E1000 PHY and Auto-Neg is enabled. If we 1250 * have Si on board that is 82544 or newer, Auto 1251 * Speed Detection takes care of MAC speed/duplex 1252 * configuration. So we only need to configure Collision 1253 * Distance in the MAC. Otherwise, we need to force 1254 * speed/duplex on the MAC to the current PHY speed/duplex 1255 * settings. 1256 */ 1257 if (mac->type == e1000_82544) 1258 hw->mac.ops.config_collision_dist(hw); 1259 else { 1260 ret_val = e1000_config_mac_to_phy_82543(hw); 1261 if (ret_val) { 1262 DEBUGOUT("Error configuring MAC to PHY settings\n"); 1263 goto out; 1264 } 1265 } 1266 1267 /* 1268 * Configure Flow Control now that Auto-Neg has completed. 1269 * First, we need to restore the desired flow control 1270 * settings because we may have had to re-autoneg with a 1271 * different link partner. 1272 */ 1273 ret_val = e1000_config_fc_after_link_up_generic(hw); 1274 if (ret_val) 1275 DEBUGOUT("Error configuring flow control\n"); 1276 1277 /* 1278 * At this point we know that we are on copper and we have 1279 * auto-negotiated link. These are conditions for checking the link 1280 * partner capability register. We use the link speed to determine if 1281 * TBI compatibility needs to be turned on or off. If the link is not 1282 * at gigabit speed, then TBI compatibility is not needed. If we are 1283 * at gigabit speed, we turn on TBI compatibility. 1284 */ 1285 if (e1000_tbi_compatibility_enabled_82543(hw)) { 1286 ret_val = mac->ops.get_link_up_info(hw, &speed, &duplex); 1287 if (ret_val) { 1288 DEBUGOUT("Error getting link speed and duplex\n"); 1289 return ret_val; 1290 } 1291 if (speed != SPEED_1000) { 1292 /* 1293 * If link speed is not set to gigabit speed, 1294 * we do not need to enable TBI compatibility. 1295 */ 1296 if (e1000_tbi_sbp_enabled_82543(hw)) { 1297 /* 1298 * If we previously were in the mode, 1299 * turn it off. 1300 */ 1301 e1000_set_tbi_sbp_82543(hw, FALSE); 1302 rctl = E1000_READ_REG(hw, E1000_RCTL); 1303 rctl &= ~E1000_RCTL_SBP; 1304 E1000_WRITE_REG(hw, E1000_RCTL, rctl); 1305 } 1306 } else { 1307 /* 1308 * If TBI compatibility is was previously off, 1309 * turn it on. For compatibility with a TBI link 1310 * partner, we will store bad packets. Some 1311 * frames have an additional byte on the end and 1312 * will look like CRC errors to to the hardware. 1313 */ 1314 if (!e1000_tbi_sbp_enabled_82543(hw)) { 1315 e1000_set_tbi_sbp_82543(hw, TRUE); 1316 rctl = E1000_READ_REG(hw, E1000_RCTL); 1317 rctl |= E1000_RCTL_SBP; 1318 E1000_WRITE_REG(hw, E1000_RCTL, rctl); 1319 } 1320 } 1321 } 1322 out: 1323 return ret_val; 1324 } 1325 1326 /** 1327 * e1000_check_for_fiber_link_82543 - Check for link (Fiber) 1328 * @hw: pointer to the HW structure 1329 * 1330 * Checks for link up on the hardware. If link is not up and we have 1331 * a signal, then we need to force link up. 1332 **/ 1333 static s32 e1000_check_for_fiber_link_82543(struct e1000_hw *hw) 1334 { 1335 struct e1000_mac_info *mac = &hw->mac; 1336 u32 rxcw, ctrl, status; 1337 s32 ret_val = E1000_SUCCESS; 1338 1339 DEBUGFUNC("e1000_check_for_fiber_link_82543"); 1340 1341 ctrl = E1000_READ_REG(hw, E1000_CTRL); 1342 status = E1000_READ_REG(hw, E1000_STATUS); 1343 rxcw = E1000_READ_REG(hw, E1000_RXCW); 1344 1345 /* 1346 * If we don't have link (auto-negotiation failed or link partner 1347 * cannot auto-negotiate), the cable is plugged in (we have signal), 1348 * and our link partner is not trying to auto-negotiate with us (we 1349 * are receiving idles or data), we need to force link up. We also 1350 * need to give auto-negotiation time to complete, in case the cable 1351 * was just plugged in. The autoneg_failed flag does this. 1352 */ 1353 /* (ctrl & E1000_CTRL_SWDPIN1) == 0 == have signal */ 1354 if ((!(ctrl & E1000_CTRL_SWDPIN1)) && 1355 (!(status & E1000_STATUS_LU)) && 1356 (!(rxcw & E1000_RXCW_C))) { 1357 if (!mac->autoneg_failed) { 1358 mac->autoneg_failed = TRUE; 1359 ret_val = 0; 1360 goto out; 1361 } 1362 DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\n"); 1363 1364 /* Disable auto-negotiation in the TXCW register */ 1365 E1000_WRITE_REG(hw, E1000_TXCW, (mac->txcw & ~E1000_TXCW_ANE)); 1366 1367 /* Force link-up and also force full-duplex. */ 1368 ctrl = E1000_READ_REG(hw, E1000_CTRL); 1369 ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD); 1370 E1000_WRITE_REG(hw, E1000_CTRL, ctrl); 1371 1372 /* Configure Flow Control after forcing link up. */ 1373 ret_val = e1000_config_fc_after_link_up_generic(hw); 1374 if (ret_val) { 1375 DEBUGOUT("Error configuring flow control\n"); 1376 goto out; 1377 } 1378 } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { 1379 /* 1380 * If we are forcing link and we are receiving /C/ ordered 1381 * sets, re-enable auto-negotiation in the TXCW register 1382 * and disable forced link in the Device Control register 1383 * in an attempt to auto-negotiate with our link partner. 1384 */ 1385 DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n"); 1386 E1000_WRITE_REG(hw, E1000_TXCW, mac->txcw); 1387 E1000_WRITE_REG(hw, E1000_CTRL, (ctrl & ~E1000_CTRL_SLU)); 1388 1389 mac->serdes_has_link = TRUE; 1390 } 1391 1392 out: 1393 return ret_val; 1394 } 1395 1396 /** 1397 * e1000_config_mac_to_phy_82543 - Configure MAC to PHY settings 1398 * @hw: pointer to the HW structure 1399 * 1400 * For the 82543 silicon, we need to set the MAC to match the settings 1401 * of the PHY, even if the PHY is auto-negotiating. 1402 **/ 1403 static s32 e1000_config_mac_to_phy_82543(struct e1000_hw *hw) 1404 { 1405 u32 ctrl; 1406 s32 ret_val = E1000_SUCCESS; 1407 u16 phy_data; 1408 1409 DEBUGFUNC("e1000_config_mac_to_phy_82543"); 1410 1411 if (!(hw->phy.ops.read_reg)) 1412 goto out; 1413 1414 /* Set the bits to force speed and duplex */ 1415 ctrl = E1000_READ_REG(hw, E1000_CTRL); 1416 ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 1417 ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS); 1418 1419 /* 1420 * Set up duplex in the Device Control and Transmit Control 1421 * registers depending on negotiated values. 1422 */ 1423 ret_val = hw->phy.ops.read_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); 1424 if (ret_val) 1425 goto out; 1426 1427 ctrl &= ~E1000_CTRL_FD; 1428 if (phy_data & M88E1000_PSSR_DPLX) 1429 ctrl |= E1000_CTRL_FD; 1430 1431 hw->mac.ops.config_collision_dist(hw); 1432 1433 /* 1434 * Set up speed in the Device Control register depending on 1435 * negotiated values. 1436 */ 1437 if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) 1438 ctrl |= E1000_CTRL_SPD_1000; 1439 else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS) 1440 ctrl |= E1000_CTRL_SPD_100; 1441 1442 E1000_WRITE_REG(hw, E1000_CTRL, ctrl); 1443 1444 out: 1445 return ret_val; 1446 } 1447 1448 /** 1449 * e1000_write_vfta_82543 - Write value to VLAN filter table 1450 * @hw: pointer to the HW structure 1451 * @offset: the 32-bit offset in which to write the value to. 1452 * @value: the 32-bit value to write at location offset. 1453 * 1454 * This writes a 32-bit value to a 32-bit offset in the VLAN filter 1455 * table. 1456 **/ 1457 static void e1000_write_vfta_82543(struct e1000_hw *hw, u32 offset, u32 value) 1458 { 1459 u32 temp; 1460 1461 DEBUGFUNC("e1000_write_vfta_82543"); 1462 1463 if ((hw->mac.type == e1000_82544) && (offset & 1)) { 1464 temp = E1000_READ_REG_ARRAY(hw, E1000_VFTA, offset - 1); 1465 E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, value); 1466 E1000_WRITE_FLUSH(hw); 1467 E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset - 1, temp); 1468 E1000_WRITE_FLUSH(hw); 1469 } else { 1470 e1000_write_vfta_generic(hw, offset, value); 1471 } 1472 } 1473 1474 /** 1475 * e1000_led_on_82543 - Turn on SW controllable LED 1476 * @hw: pointer to the HW structure 1477 * 1478 * Turns the SW defined LED on. 1479 **/ 1480 static s32 e1000_led_on_82543(struct e1000_hw *hw) 1481 { 1482 u32 ctrl = E1000_READ_REG(hw, E1000_CTRL); 1483 1484 DEBUGFUNC("e1000_led_on_82543"); 1485 1486 if (hw->mac.type == e1000_82544 && 1487 hw->phy.media_type == e1000_media_type_copper) { 1488 /* Clear SW-definable Pin 0 to turn on the LED */ 1489 ctrl &= ~E1000_CTRL_SWDPIN0; 1490 ctrl |= E1000_CTRL_SWDPIO0; 1491 } else { 1492 /* Fiber 82544 and all 82543 use this method */ 1493 ctrl |= E1000_CTRL_SWDPIN0; 1494 ctrl |= E1000_CTRL_SWDPIO0; 1495 } 1496 E1000_WRITE_REG(hw, E1000_CTRL, ctrl); 1497 1498 return E1000_SUCCESS; 1499 } 1500 1501 /** 1502 * e1000_led_off_82543 - Turn off SW controllable LED 1503 * @hw: pointer to the HW structure 1504 * 1505 * Turns the SW defined LED off. 1506 **/ 1507 static s32 e1000_led_off_82543(struct e1000_hw *hw) 1508 { 1509 u32 ctrl = E1000_READ_REG(hw, E1000_CTRL); 1510 1511 DEBUGFUNC("e1000_led_off_82543"); 1512 1513 if (hw->mac.type == e1000_82544 && 1514 hw->phy.media_type == e1000_media_type_copper) { 1515 /* Set SW-definable Pin 0 to turn off the LED */ 1516 ctrl |= E1000_CTRL_SWDPIN0; 1517 ctrl |= E1000_CTRL_SWDPIO0; 1518 } else { 1519 ctrl &= ~E1000_CTRL_SWDPIN0; 1520 ctrl |= E1000_CTRL_SWDPIO0; 1521 } 1522 E1000_WRITE_REG(hw, E1000_CTRL, ctrl); 1523 1524 return E1000_SUCCESS; 1525 } 1526 1527 /** 1528 * e1000_clear_hw_cntrs_82543 - Clear device specific hardware counters 1529 * @hw: pointer to the HW structure 1530 * 1531 * Clears the hardware counters by reading the counter registers. 1532 **/ 1533 static void e1000_clear_hw_cntrs_82543(struct e1000_hw *hw) 1534 { 1535 DEBUGFUNC("e1000_clear_hw_cntrs_82543"); 1536 1537 e1000_clear_hw_cntrs_base_generic(hw); 1538 1539 E1000_READ_REG(hw, E1000_PRC64); 1540 E1000_READ_REG(hw, E1000_PRC127); 1541 E1000_READ_REG(hw, E1000_PRC255); 1542 E1000_READ_REG(hw, E1000_PRC511); 1543 E1000_READ_REG(hw, E1000_PRC1023); 1544 E1000_READ_REG(hw, E1000_PRC1522); 1545 E1000_READ_REG(hw, E1000_PTC64); 1546 E1000_READ_REG(hw, E1000_PTC127); 1547 E1000_READ_REG(hw, E1000_PTC255); 1548 E1000_READ_REG(hw, E1000_PTC511); 1549 E1000_READ_REG(hw, E1000_PTC1023); 1550 E1000_READ_REG(hw, E1000_PTC1522); 1551 1552 E1000_READ_REG(hw, E1000_ALGNERRC); 1553 E1000_READ_REG(hw, E1000_RXERRC); 1554 E1000_READ_REG(hw, E1000_TNCRS); 1555 E1000_READ_REG(hw, E1000_CEXTERR); 1556 E1000_READ_REG(hw, E1000_TSCTC); 1557 E1000_READ_REG(hw, E1000_TSCTFC); 1558 } 1559 1560 /** 1561 * e1000_read_mac_addr_82543 - Read device MAC address 1562 * @hw: pointer to the HW structure 1563 * 1564 * Reads the device MAC address from the EEPROM and stores the value. 1565 * Since devices with two ports use the same EEPROM, we increment the 1566 * last bit in the MAC address for the second port. 1567 * 1568 **/ 1569 s32 e1000_read_mac_addr_82543(struct e1000_hw *hw) 1570 { 1571 s32 ret_val = E1000_SUCCESS; 1572 u16 offset, nvm_data, i; 1573 1574 DEBUGFUNC("e1000_read_mac_addr"); 1575 1576 for (i = 0; i < ETH_ADDR_LEN; i += 2) { 1577 offset = i >> 1; 1578 ret_val = hw->nvm.ops.read(hw, offset, 1, &nvm_data); 1579 if (ret_val) { 1580 DEBUGOUT("NVM Read Error\n"); 1581 goto out; 1582 } 1583 hw->mac.perm_addr[i] = (u8)(nvm_data & 0xFF); 1584 hw->mac.perm_addr[i+1] = (u8)(nvm_data >> 8); 1585 } 1586 1587 /* Flip last bit of mac address if we're on second port */ 1588 if (hw->bus.func == E1000_FUNC_1) 1589 hw->mac.perm_addr[5] ^= 1; 1590 1591 for (i = 0; i < ETH_ADDR_LEN; i++) 1592 hw->mac.addr[i] = hw->mac.perm_addr[i]; 1593 1594 out: 1595 return ret_val; 1596 } 1597