1 /****************************************************************************** 2 3 Copyright (c) 2001-2010, Intel Corporation 4 All rights reserved. 5 6 Redistribution and use in source and binary forms, with or without 7 modification, are permitted provided that the following conditions are met: 8 9 1. Redistributions of source code must retain the above copyright notice, 10 this list of conditions and the following disclaimer. 11 12 2. Redistributions in binary form must reproduce the above copyright 13 notice, this list of conditions and the following disclaimer in the 14 documentation and/or other materials provided with the distribution. 15 16 3. Neither the name of the Intel Corporation nor the names of its 17 contributors may be used to endorse or promote products derived from 18 this software without specific prior written permission. 19 20 THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 21 AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 22 IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 23 ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE 24 LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR 25 CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF 26 SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS 27 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 28 CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 29 ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 30 POSSIBILITY OF SUCH DAMAGE. 31 32 ******************************************************************************/ 33 /*$FreeBSD$*/ 34 35 /* 36 * 80003ES2LAN Gigabit Ethernet Controller (Copper) 37 * 80003ES2LAN Gigabit Ethernet Controller (Serdes) 38 */ 39 40 #include "e1000_api.h" 41 42 static s32 e1000_init_phy_params_80003es2lan(struct e1000_hw *hw); 43 static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw); 44 static s32 e1000_init_mac_params_80003es2lan(struct e1000_hw *hw); 45 static s32 e1000_acquire_phy_80003es2lan(struct e1000_hw *hw); 46 static void e1000_release_phy_80003es2lan(struct e1000_hw *hw); 47 static s32 e1000_acquire_nvm_80003es2lan(struct e1000_hw *hw); 48 static void e1000_release_nvm_80003es2lan(struct e1000_hw *hw); 49 static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw, 50 u32 offset, 51 u16 *data); 52 static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw, 53 u32 offset, 54 u16 data); 55 static s32 e1000_write_nvm_80003es2lan(struct e1000_hw *hw, u16 offset, 56 u16 words, u16 *data); 57 static s32 e1000_get_cfg_done_80003es2lan(struct e1000_hw *hw); 58 static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw); 59 static s32 e1000_get_cable_length_80003es2lan(struct e1000_hw *hw); 60 static s32 e1000_get_link_up_info_80003es2lan(struct e1000_hw *hw, u16 *speed, 61 u16 *duplex); 62 static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw); 63 static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw); 64 static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw); 65 static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw); 66 static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask); 67 static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex); 68 static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw); 69 static s32 e1000_cfg_on_link_up_80003es2lan(struct e1000_hw *hw); 70 static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, 71 u16 *data); 72 static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, 73 u16 data); 74 static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw); 75 static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw); 76 static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask); 77 static s32 e1000_read_mac_addr_80003es2lan(struct e1000_hw *hw); 78 static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw); 79 80 /* 81 * A table for the GG82563 cable length where the range is defined 82 * with a lower bound at "index" and the upper bound at 83 * "index + 5". 84 */ 85 static const u16 e1000_gg82563_cable_length_table[] = { 86 0, 60, 115, 150, 150, 60, 115, 150, 180, 180, 0xFF }; 87 #define GG82563_CABLE_LENGTH_TABLE_SIZE \ 88 (sizeof(e1000_gg82563_cable_length_table) / \ 89 sizeof(e1000_gg82563_cable_length_table[0])) 90 91 /** 92 * e1000_init_phy_params_80003es2lan - Init ESB2 PHY func ptrs. 93 * @hw: pointer to the HW structure 94 **/ 95 static s32 e1000_init_phy_params_80003es2lan(struct e1000_hw *hw) 96 { 97 struct e1000_phy_info *phy = &hw->phy; 98 s32 ret_val = E1000_SUCCESS; 99 100 DEBUGFUNC("e1000_init_phy_params_80003es2lan"); 101 102 if (hw->phy.media_type != e1000_media_type_copper) { 103 phy->type = e1000_phy_none; 104 goto out; 105 } else { 106 phy->ops.power_up = e1000_power_up_phy_copper; 107 phy->ops.power_down = e1000_power_down_phy_copper_80003es2lan; 108 } 109 110 phy->addr = 1; 111 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; 112 phy->reset_delay_us = 100; 113 phy->type = e1000_phy_gg82563; 114 115 phy->ops.acquire = e1000_acquire_phy_80003es2lan; 116 phy->ops.check_polarity = e1000_check_polarity_m88; 117 phy->ops.check_reset_block = e1000_check_reset_block_generic; 118 phy->ops.commit = e1000_phy_sw_reset_generic; 119 phy->ops.get_cfg_done = e1000_get_cfg_done_80003es2lan; 120 phy->ops.get_info = e1000_get_phy_info_m88; 121 phy->ops.release = e1000_release_phy_80003es2lan; 122 phy->ops.reset = e1000_phy_hw_reset_generic; 123 phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_generic; 124 125 phy->ops.force_speed_duplex = e1000_phy_force_speed_duplex_80003es2lan; 126 phy->ops.get_cable_length = e1000_get_cable_length_80003es2lan; 127 phy->ops.read_reg = e1000_read_phy_reg_gg82563_80003es2lan; 128 phy->ops.write_reg = e1000_write_phy_reg_gg82563_80003es2lan; 129 130 phy->ops.cfg_on_link_up = e1000_cfg_on_link_up_80003es2lan; 131 132 /* This can only be done after all function pointers are setup. */ 133 ret_val = e1000_get_phy_id(hw); 134 135 /* Verify phy id */ 136 if (phy->id != GG82563_E_PHY_ID) { 137 ret_val = -E1000_ERR_PHY; 138 goto out; 139 } 140 141 out: 142 return ret_val; 143 } 144 145 /** 146 * e1000_init_nvm_params_80003es2lan - Init ESB2 NVM func ptrs. 147 * @hw: pointer to the HW structure 148 **/ 149 static s32 e1000_init_nvm_params_80003es2lan(struct e1000_hw *hw) 150 { 151 struct e1000_nvm_info *nvm = &hw->nvm; 152 u32 eecd = E1000_READ_REG(hw, E1000_EECD); 153 u16 size; 154 155 DEBUGFUNC("e1000_init_nvm_params_80003es2lan"); 156 157 nvm->opcode_bits = 8; 158 nvm->delay_usec = 1; 159 switch (nvm->override) { 160 case e1000_nvm_override_spi_large: 161 nvm->page_size = 32; 162 nvm->address_bits = 16; 163 break; 164 case e1000_nvm_override_spi_small: 165 nvm->page_size = 8; 166 nvm->address_bits = 8; 167 break; 168 default: 169 nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8; 170 nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8; 171 break; 172 } 173 174 nvm->type = e1000_nvm_eeprom_spi; 175 176 size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >> 177 E1000_EECD_SIZE_EX_SHIFT); 178 179 /* 180 * Added to a constant, "size" becomes the left-shift value 181 * for setting word_size. 182 */ 183 size += NVM_WORD_SIZE_BASE_SHIFT; 184 185 /* EEPROM access above 16k is unsupported */ 186 if (size > 14) 187 size = 14; 188 nvm->word_size = 1 << size; 189 190 /* Function Pointers */ 191 nvm->ops.acquire = e1000_acquire_nvm_80003es2lan; 192 nvm->ops.read = e1000_read_nvm_eerd; 193 nvm->ops.release = e1000_release_nvm_80003es2lan; 194 nvm->ops.update = e1000_update_nvm_checksum_generic; 195 nvm->ops.valid_led_default = e1000_valid_led_default_generic; 196 nvm->ops.validate = e1000_validate_nvm_checksum_generic; 197 nvm->ops.write = e1000_write_nvm_80003es2lan; 198 199 return E1000_SUCCESS; 200 } 201 202 /** 203 * e1000_init_mac_params_80003es2lan - Init ESB2 MAC func ptrs. 204 * @hw: pointer to the HW structure 205 **/ 206 static s32 e1000_init_mac_params_80003es2lan(struct e1000_hw *hw) 207 { 208 struct e1000_mac_info *mac = &hw->mac; 209 210 DEBUGFUNC("e1000_init_mac_params_80003es2lan"); 211 212 /* Set media type and media-dependent function pointers */ 213 switch (hw->device_id) { 214 case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: 215 hw->phy.media_type = e1000_media_type_internal_serdes; 216 mac->ops.check_for_link = e1000_check_for_serdes_link_generic; 217 mac->ops.setup_physical_interface = 218 e1000_setup_fiber_serdes_link_generic; 219 break; 220 default: 221 hw->phy.media_type = e1000_media_type_copper; 222 mac->ops.check_for_link = e1000_check_for_copper_link_generic; 223 mac->ops.setup_physical_interface = 224 e1000_setup_copper_link_80003es2lan; 225 break; 226 } 227 228 /* Set mta register count */ 229 mac->mta_reg_count = 128; 230 /* Set rar entry count */ 231 mac->rar_entry_count = E1000_RAR_ENTRIES; 232 /* Set if part includes ASF firmware */ 233 mac->asf_firmware_present = TRUE; 234 /* FWSM register */ 235 mac->has_fwsm = TRUE; 236 /* ARC supported; valid only if manageability features are enabled. */ 237 mac->arc_subsystem_valid = 238 (E1000_READ_REG(hw, E1000_FWSM) & E1000_FWSM_MODE_MASK) 239 ? TRUE : FALSE; 240 /* Adaptive IFS not supported */ 241 mac->adaptive_ifs = FALSE; 242 243 /* Function pointers */ 244 245 /* bus type/speed/width */ 246 mac->ops.get_bus_info = e1000_get_bus_info_pcie_generic; 247 /* reset */ 248 mac->ops.reset_hw = e1000_reset_hw_80003es2lan; 249 /* hw initialization */ 250 mac->ops.init_hw = e1000_init_hw_80003es2lan; 251 /* link setup */ 252 mac->ops.setup_link = e1000_setup_link_generic; 253 /* check management mode */ 254 mac->ops.check_mng_mode = e1000_check_mng_mode_generic; 255 /* multicast address update */ 256 mac->ops.update_mc_addr_list = e1000_update_mc_addr_list_generic; 257 /* writing VFTA */ 258 mac->ops.write_vfta = e1000_write_vfta_generic; 259 /* clearing VFTA */ 260 mac->ops.clear_vfta = e1000_clear_vfta_generic; 261 /* read mac address */ 262 mac->ops.read_mac_addr = e1000_read_mac_addr_80003es2lan; 263 /* ID LED init */ 264 mac->ops.id_led_init = e1000_id_led_init_generic; 265 /* blink LED */ 266 mac->ops.blink_led = e1000_blink_led_generic; 267 /* setup LED */ 268 mac->ops.setup_led = e1000_setup_led_generic; 269 /* cleanup LED */ 270 mac->ops.cleanup_led = e1000_cleanup_led_generic; 271 /* turn on/off LED */ 272 mac->ops.led_on = e1000_led_on_generic; 273 mac->ops.led_off = e1000_led_off_generic; 274 /* clear hardware counters */ 275 mac->ops.clear_hw_cntrs = e1000_clear_hw_cntrs_80003es2lan; 276 /* link info */ 277 mac->ops.get_link_up_info = e1000_get_link_up_info_80003es2lan; 278 279 /* set lan id for port to determine which phy lock to use */ 280 hw->mac.ops.set_lan_id(hw); 281 282 return E1000_SUCCESS; 283 } 284 285 /** 286 * e1000_init_function_pointers_80003es2lan - Init ESB2 func ptrs. 287 * @hw: pointer to the HW structure 288 * 289 * Called to initialize all function pointers and parameters. 290 **/ 291 void e1000_init_function_pointers_80003es2lan(struct e1000_hw *hw) 292 { 293 DEBUGFUNC("e1000_init_function_pointers_80003es2lan"); 294 295 hw->mac.ops.init_params = e1000_init_mac_params_80003es2lan; 296 hw->nvm.ops.init_params = e1000_init_nvm_params_80003es2lan; 297 hw->phy.ops.init_params = e1000_init_phy_params_80003es2lan; 298 } 299 300 /** 301 * e1000_acquire_phy_80003es2lan - Acquire rights to access PHY 302 * @hw: pointer to the HW structure 303 * 304 * A wrapper to acquire access rights to the correct PHY. 305 **/ 306 static s32 e1000_acquire_phy_80003es2lan(struct e1000_hw *hw) 307 { 308 u16 mask; 309 310 DEBUGFUNC("e1000_acquire_phy_80003es2lan"); 311 312 mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM; 313 return e1000_acquire_swfw_sync_80003es2lan(hw, mask); 314 } 315 316 /** 317 * e1000_release_phy_80003es2lan - Release rights to access PHY 318 * @hw: pointer to the HW structure 319 * 320 * A wrapper to release access rights to the correct PHY. 321 **/ 322 static void e1000_release_phy_80003es2lan(struct e1000_hw *hw) 323 { 324 u16 mask; 325 326 DEBUGFUNC("e1000_release_phy_80003es2lan"); 327 328 mask = hw->bus.func ? E1000_SWFW_PHY1_SM : E1000_SWFW_PHY0_SM; 329 e1000_release_swfw_sync_80003es2lan(hw, mask); 330 } 331 332 /** 333 * e1000_acquire_mac_csr_80003es2lan - Acquire rights to access Kumeran register 334 * @hw: pointer to the HW structure 335 * 336 * Acquire the semaphore to access the Kumeran interface. 337 * 338 **/ 339 static s32 e1000_acquire_mac_csr_80003es2lan(struct e1000_hw *hw) 340 { 341 u16 mask; 342 343 DEBUGFUNC("e1000_acquire_mac_csr_80003es2lan"); 344 345 mask = E1000_SWFW_CSR_SM; 346 347 return e1000_acquire_swfw_sync_80003es2lan(hw, mask); 348 } 349 350 /** 351 * e1000_release_mac_csr_80003es2lan - Release rights to access Kumeran Register 352 * @hw: pointer to the HW structure 353 * 354 * Release the semaphore used to access the Kumeran interface 355 **/ 356 static void e1000_release_mac_csr_80003es2lan(struct e1000_hw *hw) 357 { 358 u16 mask; 359 360 DEBUGFUNC("e1000_release_mac_csr_80003es2lan"); 361 362 mask = E1000_SWFW_CSR_SM; 363 364 e1000_release_swfw_sync_80003es2lan(hw, mask); 365 } 366 367 /** 368 * e1000_acquire_nvm_80003es2lan - Acquire rights to access NVM 369 * @hw: pointer to the HW structure 370 * 371 * Acquire the semaphore to access the EEPROM. 372 **/ 373 static s32 e1000_acquire_nvm_80003es2lan(struct e1000_hw *hw) 374 { 375 s32 ret_val; 376 377 DEBUGFUNC("e1000_acquire_nvm_80003es2lan"); 378 379 ret_val = e1000_acquire_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM); 380 if (ret_val) 381 goto out; 382 383 ret_val = e1000_acquire_nvm_generic(hw); 384 385 if (ret_val) 386 e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM); 387 388 out: 389 return ret_val; 390 } 391 392 /** 393 * e1000_release_nvm_80003es2lan - Relinquish rights to access NVM 394 * @hw: pointer to the HW structure 395 * 396 * Release the semaphore used to access the EEPROM. 397 **/ 398 static void e1000_release_nvm_80003es2lan(struct e1000_hw *hw) 399 { 400 DEBUGFUNC("e1000_release_nvm_80003es2lan"); 401 402 e1000_release_nvm_generic(hw); 403 e1000_release_swfw_sync_80003es2lan(hw, E1000_SWFW_EEP_SM); 404 } 405 406 /** 407 * e1000_acquire_swfw_sync_80003es2lan - Acquire SW/FW semaphore 408 * @hw: pointer to the HW structure 409 * @mask: specifies which semaphore to acquire 410 * 411 * Acquire the SW/FW semaphore to access the PHY or NVM. The mask 412 * will also specify which port we're acquiring the lock for. 413 **/ 414 static s32 e1000_acquire_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask) 415 { 416 u32 swfw_sync; 417 u32 swmask = mask; 418 u32 fwmask = mask << 16; 419 s32 ret_val = E1000_SUCCESS; 420 s32 i = 0, timeout = 50; 421 422 DEBUGFUNC("e1000_acquire_swfw_sync_80003es2lan"); 423 424 while (i < timeout) { 425 if (e1000_get_hw_semaphore_generic(hw)) { 426 ret_val = -E1000_ERR_SWFW_SYNC; 427 goto out; 428 } 429 430 swfw_sync = E1000_READ_REG(hw, E1000_SW_FW_SYNC); 431 if (!(swfw_sync & (fwmask | swmask))) 432 break; 433 434 /* 435 * Firmware currently using resource (fwmask) 436 * or other software thread using resource (swmask) 437 */ 438 e1000_put_hw_semaphore_generic(hw); 439 msec_delay_irq(5); 440 i++; 441 } 442 443 if (i == timeout) { 444 DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n"); 445 ret_val = -E1000_ERR_SWFW_SYNC; 446 goto out; 447 } 448 449 swfw_sync |= swmask; 450 E1000_WRITE_REG(hw, E1000_SW_FW_SYNC, swfw_sync); 451 452 e1000_put_hw_semaphore_generic(hw); 453 454 out: 455 return ret_val; 456 } 457 458 /** 459 * e1000_release_swfw_sync_80003es2lan - Release SW/FW semaphore 460 * @hw: pointer to the HW structure 461 * @mask: specifies which semaphore to acquire 462 * 463 * Release the SW/FW semaphore used to access the PHY or NVM. The mask 464 * will also specify which port we're releasing the lock for. 465 **/ 466 static void e1000_release_swfw_sync_80003es2lan(struct e1000_hw *hw, u16 mask) 467 { 468 u32 swfw_sync; 469 470 DEBUGFUNC("e1000_release_swfw_sync_80003es2lan"); 471 472 while (e1000_get_hw_semaphore_generic(hw) != E1000_SUCCESS) 473 ; /* Empty */ 474 475 swfw_sync = E1000_READ_REG(hw, E1000_SW_FW_SYNC); 476 swfw_sync &= ~mask; 477 E1000_WRITE_REG(hw, E1000_SW_FW_SYNC, swfw_sync); 478 479 e1000_put_hw_semaphore_generic(hw); 480 } 481 482 /** 483 * e1000_read_phy_reg_gg82563_80003es2lan - Read GG82563 PHY register 484 * @hw: pointer to the HW structure 485 * @offset: offset of the register to read 486 * @data: pointer to the data returned from the operation 487 * 488 * Read the GG82563 PHY register. 489 **/ 490 static s32 e1000_read_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw, 491 u32 offset, u16 *data) 492 { 493 s32 ret_val; 494 u32 page_select; 495 u16 temp; 496 497 DEBUGFUNC("e1000_read_phy_reg_gg82563_80003es2lan"); 498 499 ret_val = e1000_acquire_phy_80003es2lan(hw); 500 if (ret_val) 501 goto out; 502 503 /* Select Configuration Page */ 504 if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { 505 page_select = GG82563_PHY_PAGE_SELECT; 506 } else { 507 /* 508 * Use Alternative Page Select register to access 509 * registers 30 and 31 510 */ 511 page_select = GG82563_PHY_PAGE_SELECT_ALT; 512 } 513 514 temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT); 515 ret_val = e1000_write_phy_reg_mdic(hw, page_select, temp); 516 if (ret_val) { 517 e1000_release_phy_80003es2lan(hw); 518 goto out; 519 } 520 521 if (hw->dev_spec._80003es2lan.mdic_wa_enable == TRUE) { 522 /* 523 * The "ready" bit in the MDIC register may be incorrectly set 524 * before the device has completed the "Page Select" MDI 525 * transaction. So we wait 200us after each MDI command... 526 */ 527 usec_delay(200); 528 529 /* ...and verify the command was successful. */ 530 ret_val = e1000_read_phy_reg_mdic(hw, page_select, &temp); 531 532 if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) { 533 ret_val = -E1000_ERR_PHY; 534 e1000_release_phy_80003es2lan(hw); 535 goto out; 536 } 537 538 usec_delay(200); 539 540 ret_val = e1000_read_phy_reg_mdic(hw, 541 MAX_PHY_REG_ADDRESS & offset, 542 data); 543 544 usec_delay(200); 545 } else { 546 ret_val = e1000_read_phy_reg_mdic(hw, 547 MAX_PHY_REG_ADDRESS & offset, 548 data); 549 } 550 551 e1000_release_phy_80003es2lan(hw); 552 553 out: 554 return ret_val; 555 } 556 557 /** 558 * e1000_write_phy_reg_gg82563_80003es2lan - Write GG82563 PHY register 559 * @hw: pointer to the HW structure 560 * @offset: offset of the register to read 561 * @data: value to write to the register 562 * 563 * Write to the GG82563 PHY register. 564 **/ 565 static s32 e1000_write_phy_reg_gg82563_80003es2lan(struct e1000_hw *hw, 566 u32 offset, u16 data) 567 { 568 s32 ret_val; 569 u32 page_select; 570 u16 temp; 571 572 DEBUGFUNC("e1000_write_phy_reg_gg82563_80003es2lan"); 573 574 ret_val = e1000_acquire_phy_80003es2lan(hw); 575 if (ret_val) 576 goto out; 577 578 /* Select Configuration Page */ 579 if ((offset & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { 580 page_select = GG82563_PHY_PAGE_SELECT; 581 } else { 582 /* 583 * Use Alternative Page Select register to access 584 * registers 30 and 31 585 */ 586 page_select = GG82563_PHY_PAGE_SELECT_ALT; 587 } 588 589 temp = (u16)((u16)offset >> GG82563_PAGE_SHIFT); 590 ret_val = e1000_write_phy_reg_mdic(hw, page_select, temp); 591 if (ret_val) { 592 e1000_release_phy_80003es2lan(hw); 593 goto out; 594 } 595 596 if (hw->dev_spec._80003es2lan.mdic_wa_enable == TRUE) { 597 /* 598 * The "ready" bit in the MDIC register may be incorrectly set 599 * before the device has completed the "Page Select" MDI 600 * transaction. So we wait 200us after each MDI command... 601 */ 602 usec_delay(200); 603 604 /* ...and verify the command was successful. */ 605 ret_val = e1000_read_phy_reg_mdic(hw, page_select, &temp); 606 607 if (((u16)offset >> GG82563_PAGE_SHIFT) != temp) { 608 ret_val = -E1000_ERR_PHY; 609 e1000_release_phy_80003es2lan(hw); 610 goto out; 611 } 612 613 usec_delay(200); 614 615 ret_val = e1000_write_phy_reg_mdic(hw, 616 MAX_PHY_REG_ADDRESS & offset, 617 data); 618 619 usec_delay(200); 620 } else { 621 ret_val = e1000_write_phy_reg_mdic(hw, 622 MAX_PHY_REG_ADDRESS & offset, 623 data); 624 } 625 626 e1000_release_phy_80003es2lan(hw); 627 628 out: 629 return ret_val; 630 } 631 632 /** 633 * e1000_write_nvm_80003es2lan - Write to ESB2 NVM 634 * @hw: pointer to the HW structure 635 * @offset: offset of the register to read 636 * @words: number of words to write 637 * @data: buffer of data to write to the NVM 638 * 639 * Write "words" of data to the ESB2 NVM. 640 **/ 641 static s32 e1000_write_nvm_80003es2lan(struct e1000_hw *hw, u16 offset, 642 u16 words, u16 *data) 643 { 644 DEBUGFUNC("e1000_write_nvm_80003es2lan"); 645 646 return e1000_write_nvm_spi(hw, offset, words, data); 647 } 648 649 /** 650 * e1000_get_cfg_done_80003es2lan - Wait for configuration to complete 651 * @hw: pointer to the HW structure 652 * 653 * Wait a specific amount of time for manageability processes to complete. 654 * This is a function pointer entry point called by the phy module. 655 **/ 656 static s32 e1000_get_cfg_done_80003es2lan(struct e1000_hw *hw) 657 { 658 s32 timeout = PHY_CFG_TIMEOUT; 659 s32 ret_val = E1000_SUCCESS; 660 u32 mask = E1000_NVM_CFG_DONE_PORT_0; 661 662 DEBUGFUNC("e1000_get_cfg_done_80003es2lan"); 663 664 if (hw->bus.func == 1) 665 mask = E1000_NVM_CFG_DONE_PORT_1; 666 667 while (timeout) { 668 if (E1000_READ_REG(hw, E1000_EEMNGCTL) & mask) 669 break; 670 msec_delay(1); 671 timeout--; 672 } 673 if (!timeout) { 674 DEBUGOUT("MNG configuration cycle has not completed.\n"); 675 ret_val = -E1000_ERR_RESET; 676 goto out; 677 } 678 679 out: 680 return ret_val; 681 } 682 683 /** 684 * e1000_phy_force_speed_duplex_80003es2lan - Force PHY speed and duplex 685 * @hw: pointer to the HW structure 686 * 687 * Force the speed and duplex settings onto the PHY. This is a 688 * function pointer entry point called by the phy module. 689 **/ 690 static s32 e1000_phy_force_speed_duplex_80003es2lan(struct e1000_hw *hw) 691 { 692 s32 ret_val = E1000_SUCCESS; 693 u16 phy_data; 694 bool link; 695 696 DEBUGFUNC("e1000_phy_force_speed_duplex_80003es2lan"); 697 698 if (!(hw->phy.ops.read_reg)) 699 goto out; 700 701 /* 702 * Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI 703 * forced whenever speed and duplex are forced. 704 */ 705 ret_val = hw->phy.ops.read_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); 706 if (ret_val) 707 goto out; 708 709 phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_AUTO; 710 ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_SPEC_CTRL, phy_data); 711 if (ret_val) 712 goto out; 713 714 DEBUGOUT1("GG82563 PSCR: %X\n", phy_data); 715 716 ret_val = hw->phy.ops.read_reg(hw, PHY_CONTROL, &phy_data); 717 if (ret_val) 718 goto out; 719 720 e1000_phy_force_speed_duplex_setup(hw, &phy_data); 721 722 /* Reset the phy to commit changes. */ 723 phy_data |= MII_CR_RESET; 724 725 ret_val = hw->phy.ops.write_reg(hw, PHY_CONTROL, phy_data); 726 if (ret_val) 727 goto out; 728 729 usec_delay(1); 730 731 if (hw->phy.autoneg_wait_to_complete) { 732 DEBUGOUT("Waiting for forced speed/duplex link " 733 "on GG82563 phy.\n"); 734 735 ret_val = e1000_phy_has_link_generic(hw, PHY_FORCE_LIMIT, 736 100000, &link); 737 if (ret_val) 738 goto out; 739 740 if (!link) { 741 /* 742 * We didn't get link. 743 * Reset the DSP and cross our fingers. 744 */ 745 ret_val = e1000_phy_reset_dsp_generic(hw); 746 if (ret_val) 747 goto out; 748 } 749 750 /* Try once more */ 751 ret_val = e1000_phy_has_link_generic(hw, PHY_FORCE_LIMIT, 752 100000, &link); 753 if (ret_val) 754 goto out; 755 } 756 757 ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data); 758 if (ret_val) 759 goto out; 760 761 /* 762 * Resetting the phy means we need to verify the TX_CLK corresponds 763 * to the link speed. 10Mbps -> 2.5MHz, else 25MHz. 764 */ 765 phy_data &= ~GG82563_MSCR_TX_CLK_MASK; 766 if (hw->mac.forced_speed_duplex & E1000_ALL_10_SPEED) 767 phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5; 768 else 769 phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25; 770 771 /* 772 * In addition, we must re-enable CRS on Tx for both half and full 773 * duplex. 774 */ 775 phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; 776 ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data); 777 778 out: 779 return ret_val; 780 } 781 782 /** 783 * e1000_get_cable_length_80003es2lan - Set approximate cable length 784 * @hw: pointer to the HW structure 785 * 786 * Find the approximate cable length as measured by the GG82563 PHY. 787 * This is a function pointer entry point called by the phy module. 788 **/ 789 static s32 e1000_get_cable_length_80003es2lan(struct e1000_hw *hw) 790 { 791 struct e1000_phy_info *phy = &hw->phy; 792 s32 ret_val = E1000_SUCCESS; 793 u16 phy_data, index; 794 795 DEBUGFUNC("e1000_get_cable_length_80003es2lan"); 796 797 if (!(hw->phy.ops.read_reg)) 798 goto out; 799 800 ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_DSP_DISTANCE, &phy_data); 801 if (ret_val) 802 goto out; 803 804 index = phy_data & GG82563_DSPD_CABLE_LENGTH; 805 806 if (index >= GG82563_CABLE_LENGTH_TABLE_SIZE - 5) { 807 ret_val = -E1000_ERR_PHY; 808 goto out; 809 } 810 811 phy->min_cable_length = e1000_gg82563_cable_length_table[index]; 812 phy->max_cable_length = e1000_gg82563_cable_length_table[index + 5]; 813 814 phy->cable_length = (phy->min_cable_length + phy->max_cable_length) / 2; 815 816 out: 817 return ret_val; 818 } 819 820 /** 821 * e1000_get_link_up_info_80003es2lan - Report speed and duplex 822 * @hw: pointer to the HW structure 823 * @speed: pointer to speed buffer 824 * @duplex: pointer to duplex buffer 825 * 826 * Retrieve the current speed and duplex configuration. 827 **/ 828 static s32 e1000_get_link_up_info_80003es2lan(struct e1000_hw *hw, u16 *speed, 829 u16 *duplex) 830 { 831 s32 ret_val; 832 833 DEBUGFUNC("e1000_get_link_up_info_80003es2lan"); 834 835 if (hw->phy.media_type == e1000_media_type_copper) { 836 ret_val = e1000_get_speed_and_duplex_copper_generic(hw, 837 speed, 838 duplex); 839 hw->phy.ops.cfg_on_link_up(hw); 840 } else { 841 ret_val = e1000_get_speed_and_duplex_fiber_serdes_generic(hw, 842 speed, 843 duplex); 844 } 845 846 return ret_val; 847 } 848 849 /** 850 * e1000_reset_hw_80003es2lan - Reset the ESB2 controller 851 * @hw: pointer to the HW structure 852 * 853 * Perform a global reset to the ESB2 controller. 854 **/ 855 static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw) 856 { 857 u32 ctrl; 858 s32 ret_val; 859 860 DEBUGFUNC("e1000_reset_hw_80003es2lan"); 861 862 /* 863 * Prevent the PCI-E bus from sticking if there is no TLP connection 864 * on the last TLP read/write transaction when MAC is reset. 865 */ 866 ret_val = e1000_disable_pcie_master_generic(hw); 867 if (ret_val) 868 DEBUGOUT("PCI-E Master disable polling has failed.\n"); 869 870 DEBUGOUT("Masking off all interrupts\n"); 871 E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); 872 873 E1000_WRITE_REG(hw, E1000_RCTL, 0); 874 E1000_WRITE_REG(hw, E1000_TCTL, E1000_TCTL_PSP); 875 E1000_WRITE_FLUSH(hw); 876 877 msec_delay(10); 878 879 ctrl = E1000_READ_REG(hw, E1000_CTRL); 880 881 ret_val = e1000_acquire_phy_80003es2lan(hw); 882 DEBUGOUT("Issuing a global reset to MAC\n"); 883 E1000_WRITE_REG(hw, E1000_CTRL, ctrl | E1000_CTRL_RST); 884 e1000_release_phy_80003es2lan(hw); 885 886 ret_val = e1000_get_auto_rd_done_generic(hw); 887 if (ret_val) 888 /* We don't want to continue accessing MAC registers. */ 889 goto out; 890 891 /* Clear any pending interrupt events. */ 892 E1000_WRITE_REG(hw, E1000_IMC, 0xffffffff); 893 E1000_READ_REG(hw, E1000_ICR); 894 895 ret_val = e1000_check_alt_mac_addr_generic(hw); 896 897 out: 898 return ret_val; 899 } 900 901 /** 902 * e1000_init_hw_80003es2lan - Initialize the ESB2 controller 903 * @hw: pointer to the HW structure 904 * 905 * Initialize the hw bits, LED, VFTA, MTA, link and hw counters. 906 **/ 907 static s32 e1000_init_hw_80003es2lan(struct e1000_hw *hw) 908 { 909 struct e1000_mac_info *mac = &hw->mac; 910 u32 reg_data; 911 s32 ret_val; 912 u16 kum_reg_data; 913 u16 i; 914 915 DEBUGFUNC("e1000_init_hw_80003es2lan"); 916 917 e1000_initialize_hw_bits_80003es2lan(hw); 918 919 /* Initialize identification LED */ 920 ret_val = mac->ops.id_led_init(hw); 921 if (ret_val) 922 DEBUGOUT("Error initializing identification LED\n"); 923 /* This is not fatal and we should not stop init due to this */ 924 925 /* Disabling VLAN filtering */ 926 DEBUGOUT("Initializing the IEEE VLAN\n"); 927 mac->ops.clear_vfta(hw); 928 929 /* Setup the receive address. */ 930 e1000_init_rx_addrs_generic(hw, mac->rar_entry_count); 931 932 /* Zero out the Multicast HASH table */ 933 DEBUGOUT("Zeroing the MTA\n"); 934 for (i = 0; i < mac->mta_reg_count; i++) 935 E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0); 936 937 /* Setup link and flow control */ 938 ret_val = mac->ops.setup_link(hw); 939 940 /* Disable IBIST slave mode (far-end loopback) */ 941 e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM, 942 &kum_reg_data); 943 kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE; 944 e1000_write_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM, 945 kum_reg_data); 946 947 /* Set the transmit descriptor write-back policy */ 948 reg_data = E1000_READ_REG(hw, E1000_TXDCTL(0)); 949 reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) | 950 E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC; 951 E1000_WRITE_REG(hw, E1000_TXDCTL(0), reg_data); 952 953 /* ...for both queues. */ 954 reg_data = E1000_READ_REG(hw, E1000_TXDCTL(1)); 955 reg_data = (reg_data & ~E1000_TXDCTL_WTHRESH) | 956 E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC; 957 E1000_WRITE_REG(hw, E1000_TXDCTL(1), reg_data); 958 959 /* Enable retransmit on late collisions */ 960 reg_data = E1000_READ_REG(hw, E1000_TCTL); 961 reg_data |= E1000_TCTL_RTLC; 962 E1000_WRITE_REG(hw, E1000_TCTL, reg_data); 963 964 /* Configure Gigabit Carry Extend Padding */ 965 reg_data = E1000_READ_REG(hw, E1000_TCTL_EXT); 966 reg_data &= ~E1000_TCTL_EXT_GCEX_MASK; 967 reg_data |= DEFAULT_TCTL_EXT_GCEX_80003ES2LAN; 968 E1000_WRITE_REG(hw, E1000_TCTL_EXT, reg_data); 969 970 /* Configure Transmit Inter-Packet Gap */ 971 reg_data = E1000_READ_REG(hw, E1000_TIPG); 972 reg_data &= ~E1000_TIPG_IPGT_MASK; 973 reg_data |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN; 974 E1000_WRITE_REG(hw, E1000_TIPG, reg_data); 975 976 reg_data = E1000_READ_REG_ARRAY(hw, E1000_FFLT, 0x0001); 977 reg_data &= ~0x00100000; 978 E1000_WRITE_REG_ARRAY(hw, E1000_FFLT, 0x0001, reg_data); 979 980 /* default to TRUE to enable the MDIC W/A */ 981 hw->dev_spec._80003es2lan.mdic_wa_enable = TRUE; 982 983 ret_val = e1000_read_kmrn_reg_80003es2lan(hw, 984 E1000_KMRNCTRLSTA_OFFSET >> 985 E1000_KMRNCTRLSTA_OFFSET_SHIFT, 986 &i); 987 if (!ret_val) { 988 if ((i & E1000_KMRNCTRLSTA_OPMODE_MASK) == 989 E1000_KMRNCTRLSTA_OPMODE_INBAND_MDIO) 990 hw->dev_spec._80003es2lan.mdic_wa_enable = FALSE; 991 } 992 993 /* 994 * Clear all of the statistics registers (clear on read). It is 995 * important that we do this after we have tried to establish link 996 * because the symbol error count will increment wildly if there 997 * is no link. 998 */ 999 e1000_clear_hw_cntrs_80003es2lan(hw); 1000 1001 return ret_val; 1002 } 1003 1004 /** 1005 * e1000_initialize_hw_bits_80003es2lan - Init hw bits of ESB2 1006 * @hw: pointer to the HW structure 1007 * 1008 * Initializes required hardware-dependent bits needed for normal operation. 1009 **/ 1010 static void e1000_initialize_hw_bits_80003es2lan(struct e1000_hw *hw) 1011 { 1012 u32 reg; 1013 1014 DEBUGFUNC("e1000_initialize_hw_bits_80003es2lan"); 1015 1016 /* Transmit Descriptor Control 0 */ 1017 reg = E1000_READ_REG(hw, E1000_TXDCTL(0)); 1018 reg |= (1 << 22); 1019 E1000_WRITE_REG(hw, E1000_TXDCTL(0), reg); 1020 1021 /* Transmit Descriptor Control 1 */ 1022 reg = E1000_READ_REG(hw, E1000_TXDCTL(1)); 1023 reg |= (1 << 22); 1024 E1000_WRITE_REG(hw, E1000_TXDCTL(1), reg); 1025 1026 /* Transmit Arbitration Control 0 */ 1027 reg = E1000_READ_REG(hw, E1000_TARC(0)); 1028 reg &= ~(0xF << 27); /* 30:27 */ 1029 if (hw->phy.media_type != e1000_media_type_copper) 1030 reg &= ~(1 << 20); 1031 E1000_WRITE_REG(hw, E1000_TARC(0), reg); 1032 1033 /* Transmit Arbitration Control 1 */ 1034 reg = E1000_READ_REG(hw, E1000_TARC(1)); 1035 if (E1000_READ_REG(hw, E1000_TCTL) & E1000_TCTL_MULR) 1036 reg &= ~(1 << 28); 1037 else 1038 reg |= (1 << 28); 1039 E1000_WRITE_REG(hw, E1000_TARC(1), reg); 1040 1041 return; 1042 } 1043 1044 /** 1045 * e1000_copper_link_setup_gg82563_80003es2lan - Configure GG82563 Link 1046 * @hw: pointer to the HW structure 1047 * 1048 * Setup some GG82563 PHY registers for obtaining link 1049 **/ 1050 static s32 e1000_copper_link_setup_gg82563_80003es2lan(struct e1000_hw *hw) 1051 { 1052 struct e1000_phy_info *phy = &hw->phy; 1053 s32 ret_val; 1054 u32 ctrl_ext; 1055 u16 data; 1056 1057 DEBUGFUNC("e1000_copper_link_setup_gg82563_80003es2lan"); 1058 1059 if (phy->reset_disable) 1060 goto skip_reset; 1061 1062 ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, 1063 &data); 1064 if (ret_val) 1065 goto out; 1066 1067 data |= GG82563_MSCR_ASSERT_CRS_ON_TX; 1068 /* Use 25MHz for both link down and 1000Base-T for Tx clock. */ 1069 data |= GG82563_MSCR_TX_CLK_1000MBPS_25; 1070 1071 ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, 1072 data); 1073 if (ret_val) 1074 goto out; 1075 1076 /* 1077 * Options: 1078 * MDI/MDI-X = 0 (default) 1079 * 0 - Auto for all speeds 1080 * 1 - MDI mode 1081 * 2 - MDI-X mode 1082 * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) 1083 */ 1084 ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_SPEC_CTRL, &data); 1085 if (ret_val) 1086 goto out; 1087 1088 data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK; 1089 1090 switch (phy->mdix) { 1091 case 1: 1092 data |= GG82563_PSCR_CROSSOVER_MODE_MDI; 1093 break; 1094 case 2: 1095 data |= GG82563_PSCR_CROSSOVER_MODE_MDIX; 1096 break; 1097 case 0: 1098 default: 1099 data |= GG82563_PSCR_CROSSOVER_MODE_AUTO; 1100 break; 1101 } 1102 1103 /* 1104 * Options: 1105 * disable_polarity_correction = 0 (default) 1106 * Automatic Correction for Reversed Cable Polarity 1107 * 0 - Disabled 1108 * 1 - Enabled 1109 */ 1110 data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE; 1111 if (phy->disable_polarity_correction) 1112 data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE; 1113 1114 ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_SPEC_CTRL, data); 1115 if (ret_val) 1116 goto out; 1117 1118 /* SW Reset the PHY so all changes take effect */ 1119 ret_val = hw->phy.ops.commit(hw); 1120 if (ret_val) { 1121 DEBUGOUT("Error Resetting the PHY\n"); 1122 goto out; 1123 } 1124 1125 skip_reset: 1126 /* Bypass Rx and Tx FIFO's */ 1127 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, 1128 E1000_KMRNCTRLSTA_OFFSET_FIFO_CTRL, 1129 E1000_KMRNCTRLSTA_FIFO_CTRL_RX_BYPASS | 1130 E1000_KMRNCTRLSTA_FIFO_CTRL_TX_BYPASS); 1131 if (ret_val) 1132 goto out; 1133 1134 ret_val = e1000_read_kmrn_reg_80003es2lan(hw, 1135 E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE, 1136 &data); 1137 if (ret_val) 1138 goto out; 1139 data |= E1000_KMRNCTRLSTA_OPMODE_E_IDLE; 1140 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, 1141 E1000_KMRNCTRLSTA_OFFSET_MAC2PHY_OPMODE, 1142 data); 1143 if (ret_val) 1144 goto out; 1145 1146 ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_SPEC_CTRL_2, &data); 1147 if (ret_val) 1148 goto out; 1149 1150 data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG; 1151 ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_SPEC_CTRL_2, data); 1152 if (ret_val) 1153 goto out; 1154 1155 ctrl_ext = E1000_READ_REG(hw, E1000_CTRL_EXT); 1156 ctrl_ext &= ~(E1000_CTRL_EXT_LINK_MODE_MASK); 1157 E1000_WRITE_REG(hw, E1000_CTRL_EXT, ctrl_ext); 1158 1159 ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_PWR_MGMT_CTRL, &data); 1160 if (ret_val) 1161 goto out; 1162 1163 /* 1164 * Do not init these registers when the HW is in IAMT mode, since the 1165 * firmware will have already initialized them. We only initialize 1166 * them if the HW is not in IAMT mode. 1167 */ 1168 if (!(hw->mac.ops.check_mng_mode(hw))) { 1169 /* Enable Electrical Idle on the PHY */ 1170 data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE; 1171 ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_PWR_MGMT_CTRL, 1172 data); 1173 if (ret_val) 1174 goto out; 1175 1176 ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, 1177 &data); 1178 if (ret_val) 1179 goto out; 1180 1181 data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 1182 ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, 1183 data); 1184 if (ret_val) 1185 goto out; 1186 } 1187 1188 /* 1189 * Workaround: Disable padding in Kumeran interface in the MAC 1190 * and in the PHY to avoid CRC errors. 1191 */ 1192 ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_INBAND_CTRL, &data); 1193 if (ret_val) 1194 goto out; 1195 1196 data |= GG82563_ICR_DIS_PADDING; 1197 ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_INBAND_CTRL, data); 1198 if (ret_val) 1199 goto out; 1200 1201 out: 1202 return ret_val; 1203 } 1204 1205 /** 1206 * e1000_setup_copper_link_80003es2lan - Setup Copper Link for ESB2 1207 * @hw: pointer to the HW structure 1208 * 1209 * Essentially a wrapper for setting up all things "copper" related. 1210 * This is a function pointer entry point called by the mac module. 1211 **/ 1212 static s32 e1000_setup_copper_link_80003es2lan(struct e1000_hw *hw) 1213 { 1214 u32 ctrl; 1215 s32 ret_val; 1216 u16 reg_data; 1217 1218 DEBUGFUNC("e1000_setup_copper_link_80003es2lan"); 1219 1220 ctrl = E1000_READ_REG(hw, E1000_CTRL); 1221 ctrl |= E1000_CTRL_SLU; 1222 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 1223 E1000_WRITE_REG(hw, E1000_CTRL, ctrl); 1224 1225 /* 1226 * Set the mac to wait the maximum time between each 1227 * iteration and increase the max iterations when 1228 * polling the phy; this fixes erroneous timeouts at 10Mbps. 1229 */ 1230 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 4), 1231 0xFFFF); 1232 if (ret_val) 1233 goto out; 1234 ret_val = e1000_read_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9), 1235 ®_data); 1236 if (ret_val) 1237 goto out; 1238 reg_data |= 0x3F; 1239 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, GG82563_REG(0x34, 9), 1240 reg_data); 1241 if (ret_val) 1242 goto out; 1243 ret_val = e1000_read_kmrn_reg_80003es2lan(hw, 1244 E1000_KMRNCTRLSTA_OFFSET_INB_CTRL, 1245 ®_data); 1246 if (ret_val) 1247 goto out; 1248 reg_data |= E1000_KMRNCTRLSTA_INB_CTRL_DIS_PADDING; 1249 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, 1250 E1000_KMRNCTRLSTA_OFFSET_INB_CTRL, 1251 reg_data); 1252 if (ret_val) 1253 goto out; 1254 1255 ret_val = e1000_copper_link_setup_gg82563_80003es2lan(hw); 1256 if (ret_val) 1257 goto out; 1258 1259 ret_val = e1000_setup_copper_link_generic(hw); 1260 1261 out: 1262 return ret_val; 1263 } 1264 1265 /** 1266 * e1000_cfg_on_link_up_80003es2lan - es2 link configuration after link-up 1267 * @hw: pointer to the HW structure 1268 * @duplex: current duplex setting 1269 * 1270 * Configure the KMRN interface by applying last minute quirks for 1271 * 10/100 operation. 1272 **/ 1273 static s32 e1000_cfg_on_link_up_80003es2lan(struct e1000_hw *hw) 1274 { 1275 s32 ret_val = E1000_SUCCESS; 1276 u16 speed; 1277 u16 duplex; 1278 1279 DEBUGFUNC("e1000_configure_on_link_up"); 1280 1281 if (hw->phy.media_type == e1000_media_type_copper) { 1282 ret_val = e1000_get_speed_and_duplex_copper_generic(hw, 1283 &speed, 1284 &duplex); 1285 if (ret_val) 1286 goto out; 1287 1288 if (speed == SPEED_1000) 1289 ret_val = e1000_cfg_kmrn_1000_80003es2lan(hw); 1290 else 1291 ret_val = e1000_cfg_kmrn_10_100_80003es2lan(hw, duplex); 1292 } 1293 1294 out: 1295 return ret_val; 1296 } 1297 1298 /** 1299 * e1000_cfg_kmrn_10_100_80003es2lan - Apply "quirks" for 10/100 operation 1300 * @hw: pointer to the HW structure 1301 * @duplex: current duplex setting 1302 * 1303 * Configure the KMRN interface by applying last minute quirks for 1304 * 10/100 operation. 1305 **/ 1306 static s32 e1000_cfg_kmrn_10_100_80003es2lan(struct e1000_hw *hw, u16 duplex) 1307 { 1308 s32 ret_val = E1000_SUCCESS; 1309 u32 tipg; 1310 u32 i = 0; 1311 u16 reg_data, reg_data2; 1312 1313 DEBUGFUNC("e1000_configure_kmrn_for_10_100"); 1314 1315 reg_data = E1000_KMRNCTRLSTA_HD_CTRL_10_100_DEFAULT; 1316 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, 1317 E1000_KMRNCTRLSTA_OFFSET_HD_CTRL, 1318 reg_data); 1319 if (ret_val) 1320 goto out; 1321 1322 /* Configure Transmit Inter-Packet Gap */ 1323 tipg = E1000_READ_REG(hw, E1000_TIPG); 1324 tipg &= ~E1000_TIPG_IPGT_MASK; 1325 tipg |= DEFAULT_TIPG_IPGT_10_100_80003ES2LAN; 1326 E1000_WRITE_REG(hw, E1000_TIPG, tipg); 1327 1328 do { 1329 ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, 1330 ®_data); 1331 if (ret_val) 1332 goto out; 1333 1334 ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, 1335 ®_data2); 1336 if (ret_val) 1337 goto out; 1338 i++; 1339 } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY)); 1340 1341 if (duplex == HALF_DUPLEX) 1342 reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER; 1343 else 1344 reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 1345 1346 ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); 1347 1348 out: 1349 return ret_val; 1350 } 1351 1352 /** 1353 * e1000_cfg_kmrn_1000_80003es2lan - Apply "quirks" for gigabit operation 1354 * @hw: pointer to the HW structure 1355 * 1356 * Configure the KMRN interface by applying last minute quirks for 1357 * gigabit operation. 1358 **/ 1359 static s32 e1000_cfg_kmrn_1000_80003es2lan(struct e1000_hw *hw) 1360 { 1361 s32 ret_val = E1000_SUCCESS; 1362 u16 reg_data, reg_data2; 1363 u32 tipg; 1364 u32 i = 0; 1365 1366 DEBUGFUNC("e1000_configure_kmrn_for_1000"); 1367 1368 reg_data = E1000_KMRNCTRLSTA_HD_CTRL_1000_DEFAULT; 1369 ret_val = e1000_write_kmrn_reg_80003es2lan(hw, 1370 E1000_KMRNCTRLSTA_OFFSET_HD_CTRL, 1371 reg_data); 1372 if (ret_val) 1373 goto out; 1374 1375 /* Configure Transmit Inter-Packet Gap */ 1376 tipg = E1000_READ_REG(hw, E1000_TIPG); 1377 tipg &= ~E1000_TIPG_IPGT_MASK; 1378 tipg |= DEFAULT_TIPG_IPGT_1000_80003ES2LAN; 1379 E1000_WRITE_REG(hw, E1000_TIPG, tipg); 1380 1381 do { 1382 ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, 1383 ®_data); 1384 if (ret_val) 1385 goto out; 1386 1387 ret_val = hw->phy.ops.read_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, 1388 ®_data2); 1389 if (ret_val) 1390 goto out; 1391 i++; 1392 } while ((reg_data != reg_data2) && (i < GG82563_MAX_KMRN_RETRY)); 1393 1394 reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 1395 ret_val = hw->phy.ops.write_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); 1396 1397 out: 1398 return ret_val; 1399 } 1400 1401 /** 1402 * e1000_read_kmrn_reg_80003es2lan - Read kumeran register 1403 * @hw: pointer to the HW structure 1404 * @offset: register offset to be read 1405 * @data: pointer to the read data 1406 * 1407 * Acquire semaphore, then read the PHY register at offset 1408 * using the kumeran interface. The information retrieved is stored in data. 1409 * Release the semaphore before exiting. 1410 **/ 1411 static s32 e1000_read_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, 1412 u16 *data) 1413 { 1414 u32 kmrnctrlsta; 1415 s32 ret_val = E1000_SUCCESS; 1416 1417 DEBUGFUNC("e1000_read_kmrn_reg_80003es2lan"); 1418 1419 ret_val = e1000_acquire_mac_csr_80003es2lan(hw); 1420 if (ret_val) 1421 goto out; 1422 1423 kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) & 1424 E1000_KMRNCTRLSTA_OFFSET) | E1000_KMRNCTRLSTA_REN; 1425 E1000_WRITE_REG(hw, E1000_KMRNCTRLSTA, kmrnctrlsta); 1426 1427 usec_delay(2); 1428 1429 kmrnctrlsta = E1000_READ_REG(hw, E1000_KMRNCTRLSTA); 1430 *data = (u16)kmrnctrlsta; 1431 1432 e1000_release_mac_csr_80003es2lan(hw); 1433 1434 out: 1435 return ret_val; 1436 } 1437 1438 /** 1439 * e1000_write_kmrn_reg_80003es2lan - Write kumeran register 1440 * @hw: pointer to the HW structure 1441 * @offset: register offset to write to 1442 * @data: data to write at register offset 1443 * 1444 * Acquire semaphore, then write the data to PHY register 1445 * at the offset using the kumeran interface. Release semaphore 1446 * before exiting. 1447 **/ 1448 static s32 e1000_write_kmrn_reg_80003es2lan(struct e1000_hw *hw, u32 offset, 1449 u16 data) 1450 { 1451 u32 kmrnctrlsta; 1452 s32 ret_val = E1000_SUCCESS; 1453 1454 DEBUGFUNC("e1000_write_kmrn_reg_80003es2lan"); 1455 1456 ret_val = e1000_acquire_mac_csr_80003es2lan(hw); 1457 if (ret_val) 1458 goto out; 1459 1460 kmrnctrlsta = ((offset << E1000_KMRNCTRLSTA_OFFSET_SHIFT) & 1461 E1000_KMRNCTRLSTA_OFFSET) | data; 1462 E1000_WRITE_REG(hw, E1000_KMRNCTRLSTA, kmrnctrlsta); 1463 1464 usec_delay(2); 1465 1466 e1000_release_mac_csr_80003es2lan(hw); 1467 1468 out: 1469 return ret_val; 1470 } 1471 1472 /** 1473 * e1000_read_mac_addr_80003es2lan - Read device MAC address 1474 * @hw: pointer to the HW structure 1475 **/ 1476 static s32 e1000_read_mac_addr_80003es2lan(struct e1000_hw *hw) 1477 { 1478 s32 ret_val = E1000_SUCCESS; 1479 1480 DEBUGFUNC("e1000_read_mac_addr_80003es2lan"); 1481 1482 /* 1483 * If there's an alternate MAC address place it in RAR0 1484 * so that it will override the Si installed default perm 1485 * address. 1486 */ 1487 ret_val = e1000_check_alt_mac_addr_generic(hw); 1488 if (ret_val) 1489 goto out; 1490 1491 ret_val = e1000_read_mac_addr_generic(hw); 1492 1493 out: 1494 return ret_val; 1495 } 1496 1497 /** 1498 * e1000_power_down_phy_copper_80003es2lan - Remove link during PHY power down 1499 * @hw: pointer to the HW structure 1500 * 1501 * In the case of a PHY power down to save power, or to turn off link during a 1502 * driver unload, or wake on lan is not enabled, remove the link. 1503 **/ 1504 static void e1000_power_down_phy_copper_80003es2lan(struct e1000_hw *hw) 1505 { 1506 /* If the management interface is not enabled, then power down */ 1507 if (!(hw->mac.ops.check_mng_mode(hw) || 1508 hw->phy.ops.check_reset_block(hw))) 1509 e1000_power_down_phy_copper(hw); 1510 1511 return; 1512 } 1513 1514 /** 1515 * e1000_clear_hw_cntrs_80003es2lan - Clear device specific hardware counters 1516 * @hw: pointer to the HW structure 1517 * 1518 * Clears the hardware counters by reading the counter registers. 1519 **/ 1520 static void e1000_clear_hw_cntrs_80003es2lan(struct e1000_hw *hw) 1521 { 1522 DEBUGFUNC("e1000_clear_hw_cntrs_80003es2lan"); 1523 1524 e1000_clear_hw_cntrs_base_generic(hw); 1525 1526 E1000_READ_REG(hw, E1000_PRC64); 1527 E1000_READ_REG(hw, E1000_PRC127); 1528 E1000_READ_REG(hw, E1000_PRC255); 1529 E1000_READ_REG(hw, E1000_PRC511); 1530 E1000_READ_REG(hw, E1000_PRC1023); 1531 E1000_READ_REG(hw, E1000_PRC1522); 1532 E1000_READ_REG(hw, E1000_PTC64); 1533 E1000_READ_REG(hw, E1000_PTC127); 1534 E1000_READ_REG(hw, E1000_PTC255); 1535 E1000_READ_REG(hw, E1000_PTC511); 1536 E1000_READ_REG(hw, E1000_PTC1023); 1537 E1000_READ_REG(hw, E1000_PTC1522); 1538 1539 E1000_READ_REG(hw, E1000_ALGNERRC); 1540 E1000_READ_REG(hw, E1000_RXERRC); 1541 E1000_READ_REG(hw, E1000_TNCRS); 1542 E1000_READ_REG(hw, E1000_CEXTERR); 1543 E1000_READ_REG(hw, E1000_TSCTC); 1544 E1000_READ_REG(hw, E1000_TSCTFC); 1545 1546 E1000_READ_REG(hw, E1000_MGTPRC); 1547 E1000_READ_REG(hw, E1000_MGTPDC); 1548 E1000_READ_REG(hw, E1000_MGTPTC); 1549 1550 E1000_READ_REG(hw, E1000_IAC); 1551 E1000_READ_REG(hw, E1000_ICRXOC); 1552 1553 E1000_READ_REG(hw, E1000_ICRXPTC); 1554 E1000_READ_REG(hw, E1000_ICRXATC); 1555 E1000_READ_REG(hw, E1000_ICTXPTC); 1556 E1000_READ_REG(hw, E1000_ICTXATC); 1557 E1000_READ_REG(hw, E1000_ICTXQEC); 1558 E1000_READ_REG(hw, E1000_ICTXQMTC); 1559 E1000_READ_REG(hw, E1000_ICRXDMTC); 1560 } 1561