xref: /freebsd/sys/dev/ata/chipsets/ata-serverworks.c (revision 8a1d183fb7736a7e56a12633f0959c918d92c1b3)

/*-
 * Copyright (c) 1998 - 2008 S�ren Schmidt <sos@FreeBSD.org>
 * All rights reserved.
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions
 * are met:
 * 1. Redistributions of source code must retain the above copyright
 *    notice, this list of conditions and the following disclaimer,
 *    without modification, immediately at the beginning of the file.
 * 2. Redistributions in binary form must reproduce the above copyright
 *    notice, this list of conditions and the following disclaimer in the
 *    documentation and/or other materials provided with the distribution.
 *
 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR
 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 */

#include <sys/cdefs.h>
__FBSDID("$FreeBSD$");

#include "opt_ata.h"
#include <sys/param.h>
#include <sys/module.h>
#include <sys/systm.h>
#include <sys/kernel.h>
#include <sys/ata.h>
#include <sys/bus.h>
#include <sys/endian.h>
#include <sys/malloc.h>
#include <sys/lock.h>
#include <sys/mutex.h>
#include <sys/sema.h>
#include <sys/taskqueue.h>
#include <vm/uma.h>
#include <machine/stdarg.h>
#include <machine/resource.h>
#include <machine/bus.h>
#include <sys/rman.h>
#include <dev/pci/pcivar.h>
#include <dev/pci/pcireg.h>
#include <dev/ata/ata-all.h>
#include <dev/ata/ata-pci.h>
#include <ata_if.h>

/* local prototypes */
static int ata_serverworks_chipinit(device_t dev);
static int ata_serverworks_ch_attach(device_t dev);
static int ata_serverworks_ch_detach(device_t dev);
static void ata_serverworks_tf_read(struct ata_request *request);
static void ata_serverworks_tf_write(struct ata_request *request);
static int ata_serverworks_setmode(device_t dev, int target, int mode);
static void ata_serverworks_sata_reset(device_t dev);
static int ata_serverworks_status(device_t dev);

/* misc defines */
#define SWKS_33		0
#define SWKS_66		1
#define SWKS_100	2
#define SWKS_MIO	3


/*
 * ServerWorks chipset support functions
 */
static int
ata_serverworks_probe(device_t dev)
{
    struct ata_pci_controller *ctlr = device_get_softc(dev);
    static struct ata_chip_id ids[] =
    {{ ATA_ROSB4,     0x00, SWKS_33,  0, ATA_WDMA2, "ROSB4" },
     { ATA_CSB5,      0x92, SWKS_100, 0, ATA_UDMA5, "CSB5" },
     { ATA_CSB5,      0x00, SWKS_66,  0, ATA_UDMA4, "CSB5" },
     { ATA_CSB6,      0x00, SWKS_100, 0, ATA_UDMA5, "CSB6" },
     { ATA_CSB6_1,    0x00, SWKS_66,  0, ATA_UDMA4, "CSB6" },
     { ATA_HT1000,    0x00, SWKS_100, 0, ATA_UDMA5, "HT1000" },
     { ATA_HT1000_S1, 0x00, SWKS_MIO, 4, ATA_SA150, "HT1000" },
     { ATA_HT1000_S2, 0x00, SWKS_MIO, 4, ATA_SA150, "HT1000" },
     { ATA_K2,        0x00, SWKS_MIO, 4, ATA_SA150, "K2" },
     { ATA_FRODO4,    0x00, SWKS_MIO, 4, ATA_SA150, "Frodo4" },
     { ATA_FRODO8,    0x00, SWKS_MIO, 8, ATA_SA150, "Frodo8" },
     { 0, 0, 0, 0, 0, 0}};

    if (pci_get_vendor(dev) != ATA_SERVERWORKS_ID)
	return ENXIO;

    if (!(ctlr->chip = ata_match_chip(dev, ids)))
	return ENXIO;

    ata_set_desc(dev);
    ctlr->chipinit = ata_serverworks_chipinit;
    return (BUS_PROBE_DEFAULT);
}

static int
ata_serverworks_status(device_t dev)
{
    struct ata_channel *ch = device_get_softc(dev);
    struct ata_pci_controller *ctlr = device_get_softc(device_get_parent(dev));

    /*
     * Check if this interrupt belongs to our channel.
     */
    if (!(ATA_INL(ctlr->r_res2, 0x1f80) & (1 << ch->unit)))
	return (0);

    /*
     * We need to do a 4-byte read on the status reg before the values
     * will report correctly
     */

    ATA_IDX_INL(ch,ATA_STATUS);

    return ata_pci_status(dev);
}

static int
ata_serverworks_chipinit(device_t dev)
{
    struct ata_pci_controller *ctlr = device_get_softc(dev);

    if (ata_setup_interrupt(dev, ata_generic_intr))
	return ENXIO;

    if (ctlr->chip->cfg1 == SWKS_MIO) {
	ctlr->r_type2 = SYS_RES_MEMORY;
	ctlr->r_rid2 = PCIR_BAR(5);
	if (!(ctlr->r_res2 = bus_alloc_resource_any(dev, ctlr->r_type2,
						    &ctlr->r_rid2, RF_ACTIVE)))
	    return ENXIO;

	ctlr->channels = ctlr->chip->cfg2;
	ctlr->ch_attach = ata_serverworks_ch_attach;
	ctlr->ch_detach = ata_serverworks_ch_detach;
	ctlr->setmode = ata_sata_setmode;
	ctlr->getrev = ata_sata_getrev;
	ctlr->reset = ata_serverworks_sata_reset;
	return 0;
    }
    else if (ctlr->chip->cfg1 == SWKS_33) {
	device_t *children;
	int nchildren, i;

	/* locate the ISA part in the southbridge and enable UDMA33 */
	if (!device_get_children(device_get_parent(dev), &children,&nchildren)){
	    for (i = 0; i < nchildren; i++) {
		if (pci_get_devid(children[i]) == ATA_ROSB4_ISA) {
		    pci_write_config(children[i], 0x64,
				     (pci_read_config(children[i], 0x64, 4) &
				      ~0x00002000) | 0x00004000, 4);
		    break;
		}
	    }
	    free(children, M_TEMP);
	}
    }
    else {
	pci_write_config(dev, 0x5a,
			 (pci_read_config(dev, 0x5a, 1) & ~0x40) |
			 (ctlr->chip->cfg1 == SWKS_100) ? 0x03 : 0x02, 1);
    }
    ctlr->setmode = ata_serverworks_setmode;
    return 0;
}

static int
ata_serverworks_ch_attach(device_t dev)
{
    struct ata_pci_controller *ctlr = device_get_softc(device_get_parent(dev));
    struct ata_channel *ch = device_get_softc(dev);
    int ch_offset;
    int i;

    ata_pci_dmainit(dev);

    ch_offset = ch->unit * 0x100;

    for (i = ATA_DATA; i < ATA_MAX_RES; i++)
	ch->r_io[i].res = ctlr->r_res2;

    /* setup ATA registers */
    ch->r_io[ATA_DATA].offset = ch_offset + 0x00;
    ch->r_io[ATA_FEATURE].offset = ch_offset + 0x04;
    ch->r_io[ATA_COUNT].offset = ch_offset + 0x08;
    ch->r_io[ATA_SECTOR].offset = ch_offset + 0x0c;
    ch->r_io[ATA_CYL_LSB].offset = ch_offset + 0x10;
    ch->r_io[ATA_CYL_MSB].offset = ch_offset + 0x14;
    ch->r_io[ATA_DRIVE].offset = ch_offset + 0x18;
    ch->r_io[ATA_COMMAND].offset = ch_offset + 0x1c;
    ch->r_io[ATA_CONTROL].offset = ch_offset + 0x20;
    ata_default_registers(dev);

    /* setup DMA registers */
    ch->r_io[ATA_BMCMD_PORT].offset = ch_offset + 0x30;
    ch->r_io[ATA_BMSTAT_PORT].offset = ch_offset + 0x32;
    ch->r_io[ATA_BMDTP_PORT].offset = ch_offset + 0x34;

    /* setup SATA registers */
    ch->r_io[ATA_SSTATUS].offset = ch_offset + 0x40;
    ch->r_io[ATA_SERROR].offset = ch_offset + 0x44;
    ch->r_io[ATA_SCONTROL].offset = ch_offset + 0x48;

    ch->flags |= ATA_NO_SLAVE | ATA_SATA | ATA_KNOWN_PRESENCE;
    ata_pci_hw(dev);
    ch->hw.tf_read = ata_serverworks_tf_read;
    ch->hw.tf_write = ata_serverworks_tf_write;

    if (ctlr->chip->chipid == ATA_K2) {
	/*
	 * Set SICR registers to turn off waiting for a status message
	 * before sending FIS. Values obtained from the Darwin driver.
	 */

	ATA_OUTL(ctlr->r_res2, ch_offset + 0x80,
	    ATA_INL(ctlr->r_res2, ch_offset + 0x80) & ~0x00040000);
	ATA_OUTL(ctlr->r_res2, ch_offset + 0x88, 0);

	/*
	 * Some controllers have a bug where they will send the command
	 * to the drive before seeing a DMA start, and then can begin
	 * receiving data before the DMA start arrives. The controller
	 * will then become confused and either corrupt the data or crash.
	 * Remedy this by starting DMA before sending the drive command.
	 */

	ch->flags |= ATA_DMA_BEFORE_CMD;

	/*
	 * The status register must be read as a long to fill the other
	 * registers.
	 */

	ch->hw.status = ata_serverworks_status;
	ch->flags |= ATA_STATUS_IS_LONG;
    }

    /* chip does not reliably do 64K DMA transfers */
    ch->dma.max_iosize = 64 * DEV_BSIZE;

    return 0;
}

static int
ata_serverworks_ch_detach(device_t dev)
{

    ata_pci_dmafini(dev);
    return (0);
}

static void
ata_serverworks_tf_read(struct ata_request *request)
{
    struct ata_channel *ch = device_get_softc(request->parent);

    if (request->flags & ATA_R_48BIT) {
	u_int16_t temp;

	request->u.ata.count = ATA_IDX_INW(ch, ATA_COUNT);
	temp = ATA_IDX_INW(ch, ATA_SECTOR);
	request->u.ata.lba = (u_int64_t)(temp & 0x00ff) |
			     ((u_int64_t)(temp & 0xff00) << 24);
	temp = ATA_IDX_INW(ch, ATA_CYL_LSB);
	request->u.ata.lba |= ((u_int64_t)(temp & 0x00ff) << 8) |
			      ((u_int64_t)(temp & 0xff00) << 32);
	temp = ATA_IDX_INW(ch, ATA_CYL_MSB);
	request->u.ata.lba |= ((u_int64_t)(temp & 0x00ff) << 16) |
			      ((u_int64_t)(temp & 0xff00) << 40);
    }
    else {
	request->u.ata.count = ATA_IDX_INW(ch, ATA_COUNT) & 0x00ff;
	request->u.ata.lba = (ATA_IDX_INW(ch, ATA_SECTOR) & 0x00ff) |
			     ((ATA_IDX_INW(ch, ATA_CYL_LSB) & 0x00ff) << 8) |
			     ((ATA_IDX_INW(ch, ATA_CYL_MSB) & 0x00ff) << 16) |
			     ((ATA_IDX_INW(ch, ATA_DRIVE) & 0xf) << 24);
    }
}

static void
ata_serverworks_tf_write(struct ata_request *request)
{
    struct ata_channel *ch = device_get_softc(request->parent);
#ifndef ATA_CAM
    struct ata_device *atadev = device_get_softc(request->dev);
#endif

    if (request->flags & ATA_R_48BIT) {
	ATA_IDX_OUTW(ch, ATA_FEATURE, request->u.ata.feature);
	ATA_IDX_OUTW(ch, ATA_COUNT, request->u.ata.count);
	ATA_IDX_OUTW(ch, ATA_SECTOR, ((request->u.ata.lba >> 16) & 0xff00) |
				      (request->u.ata.lba & 0x00ff));
	ATA_IDX_OUTW(ch, ATA_CYL_LSB, ((request->u.ata.lba >> 24) & 0xff00) |
				       ((request->u.ata.lba >> 8) & 0x00ff));
	ATA_IDX_OUTW(ch, ATA_CYL_MSB, ((request->u.ata.lba >> 32) & 0xff00) |
				       ((request->u.ata.lba >> 16) & 0x00ff));
	ATA_IDX_OUTW(ch, ATA_DRIVE, ATA_D_LBA | ATA_DEV(request->unit));
    }
    else {
	ATA_IDX_OUTW(ch, ATA_FEATURE, request->u.ata.feature);
	ATA_IDX_OUTW(ch, ATA_COUNT, request->u.ata.count);
#ifndef ATA_CAM
	if (atadev->flags & ATA_D_USE_CHS) {
	    int heads, sectors;

	    if (atadev->param.atavalid & ATA_FLAG_54_58) {
		heads = atadev->param.current_heads;
		sectors = atadev->param.current_sectors;
	    }
	    else {
		heads = atadev->param.heads;
		sectors = atadev->param.sectors;
	    }
	    ATA_IDX_OUTW(ch, ATA_SECTOR, (request->u.ata.lba % sectors)+1);
	    ATA_IDX_OUTW(ch, ATA_CYL_LSB,
			 (request->u.ata.lba / (sectors * heads)));
	    ATA_IDX_OUTW(ch, ATA_CYL_MSB,
			 (request->u.ata.lba / (sectors * heads)) >> 8);
	    ATA_IDX_OUTW(ch, ATA_DRIVE, ATA_D_IBM | ATA_DEV(request->unit) |
			 (((request->u.ata.lba% (sectors * heads)) /
			   sectors) & 0xf));
	}
	else {
#endif
	    ATA_IDX_OUTW(ch, ATA_SECTOR, request->u.ata.lba);
	    ATA_IDX_OUTW(ch, ATA_CYL_LSB, request->u.ata.lba >> 8);
	    ATA_IDX_OUTW(ch, ATA_CYL_MSB, request->u.ata.lba >> 16);
	    ATA_IDX_OUTW(ch, ATA_DRIVE,
			 ATA_D_IBM | ATA_D_LBA | ATA_DEV(request->unit) |
			 ((request->u.ata.lba >> 24) & 0x0f));
#ifndef ATA_CAM
	}
#endif
    }
}

static int
ata_serverworks_setmode(device_t dev, int target, int mode)
{
	device_t parent = device_get_parent(dev);
        struct ata_pci_controller *ctlr = device_get_softc(parent);
	struct ata_channel *ch = device_get_softc(dev);
        int devno = (ch->unit << 1) + target;
        int offset = (devno ^ 0x01) << 3;
	int piomode;
	u_int8_t piotimings[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
	u_int8_t dmatimings[] = { 0x77, 0x21, 0x20 };

	mode = min(mode, ctlr->chip->max_dma);
	if (mode >= ATA_UDMA0) {
	    /* Set UDMA mode, enable UDMA, set WDMA2/PIO4 */
	    pci_write_config(parent, 0x56,
			     (pci_read_config(parent, 0x56, 2) &
			      ~(0xf << (devno << 2))) |
			     ((mode & ATA_MODE_MASK) << (devno << 2)), 2);
	    pci_write_config(parent, 0x54,
			     pci_read_config(parent, 0x54, 1) |
			     (0x01 << devno), 1);
	    pci_write_config(parent, 0x44,
			     (pci_read_config(parent, 0x44, 4) &
			      ~(0xff << offset)) |
			     (dmatimings[2] << offset), 4);
	    piomode = ATA_PIO4;
	} else if (mode >= ATA_WDMA0) {
	    /* Disable UDMA, set WDMA mode and timings, calculate PIO. */
	    pci_write_config(parent, 0x54,
			     pci_read_config(parent, 0x54, 1) &
			      ~(0x01 << devno), 1);
	    pci_write_config(parent, 0x44,
			     (pci_read_config(parent, 0x44, 4) &
			      ~(0xff << offset)) |
			     (dmatimings[mode & ATA_MODE_MASK] << offset), 4);
	    piomode = (mode == ATA_WDMA0) ? ATA_PIO0 :
		(mode == ATA_WDMA1) ? ATA_PIO3 : ATA_PIO4;
	} else {
	    /* Disable UDMA, set requested PIO. */
	    pci_write_config(parent, 0x54,
			     pci_read_config(parent, 0x54, 1) &
			     ~(0x01 << devno), 1);
	    piomode = mode;
	}
	/* Set PIO mode and timings, calculated above. */
	if (ctlr->chip->cfg1 != SWKS_33) {
		pci_write_config(parent, 0x4a,
			 (pci_read_config(parent, 0x4a, 2) &
			  ~(0xf << (devno << 2))) |
			 ((piomode - ATA_PIO0) << (devno<<2)),2);
	}
	pci_write_config(parent, 0x40,
			 (pci_read_config(parent, 0x40, 4) &
			  ~(0xff << offset)) |
			 (piotimings[ata_mode2idx(piomode)] << offset), 4);
	return (mode);
}

static void
ata_serverworks_sata_reset(device_t dev)
{
	struct ata_channel *ch = device_get_softc(dev);

	if (ata_sata_phy_reset(dev, -1, 0))
		ata_generic_reset(dev);
	else
		ch->devices = 0;
}

ATA_DECLARE_DRIVER(ata_serverworks);