1 /*- 2 * Copyright (c) 1998 - 2007 S�ren Schmidt <sos@FreeBSD.org> 3 * All rights reserved. 4 * 5 * Redistribution and use in source and binary forms, with or without 6 * modification, are permitted provided that the following conditions 7 * are met: 8 * 1. Redistributions of source code must retain the above copyright 9 * notice, this list of conditions and the following disclaimer, 10 * without modification, immediately at the beginning of the file. 11 * 2. Redistributions in binary form must reproduce the above copyright 12 * notice, this list of conditions and the following disclaimer in the 13 * documentation and/or other materials provided with the distribution. 14 * 15 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS'' AND ANY EXPRESS OR 16 * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES 17 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 18 * IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, 19 * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 20 * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, 21 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY 22 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT 23 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF 24 * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 25 */ 26 27 #include <sys/cdefs.h> 28 __FBSDID("$FreeBSD$"); 29 30 #include "opt_ata.h" 31 #include <sys/param.h> 32 #include <sys/systm.h> 33 #include <sys/kernel.h> 34 #include <sys/endian.h> 35 #include <sys/ata.h> 36 #include <sys/conf.h> 37 #include <sys/ctype.h> 38 #include <sys/bus.h> 39 #include <sys/sema.h> 40 #include <sys/taskqueue.h> 41 #include <vm/uma.h> 42 #include <machine/bus.h> 43 #include <sys/rman.h> 44 #include <dev/ata/ata-all.h> 45 #include <dev/ata/ata-pci.h> 46 #include <ata_if.h> 47 48 /* prototypes */ 49 static int ata_generic_status(device_t dev); 50 static int ata_wait(struct ata_channel *ch, struct ata_device *, u_int8_t); 51 static void ata_pio_read(struct ata_request *, int); 52 static void ata_pio_write(struct ata_request *, int); 53 static void ata_tf_read(struct ata_request *); 54 static void ata_tf_write(struct ata_request *); 55 56 /* 57 * low level ATA functions 58 */ 59 void 60 ata_generic_hw(device_t dev) 61 { 62 struct ata_channel *ch = device_get_softc(dev); 63 64 ch->hw.begin_transaction = ata_begin_transaction; 65 ch->hw.end_transaction = ata_end_transaction; 66 ch->hw.status = ata_generic_status; 67 ch->hw.command = ata_generic_command; 68 ch->hw.tf_read = ata_tf_read; 69 ch->hw.tf_write = ata_tf_write; 70 } 71 72 /* must be called with ATA channel locked and state_mtx held */ 73 int 74 ata_begin_transaction(struct ata_request *request) 75 { 76 struct ata_channel *ch = device_get_softc(device_get_parent(request->dev)); 77 struct ata_device *atadev = device_get_softc(request->dev); 78 int dummy, error; 79 80 ATA_DEBUG_RQ(request, "begin transaction"); 81 82 /* disable ATAPI DMA writes if HW doesn't support it */ 83 if ((ch->flags & ATA_ATAPI_DMA_RO) && 84 ((request->flags & (ATA_R_ATAPI | ATA_R_DMA | ATA_R_WRITE)) == 85 (ATA_R_ATAPI | ATA_R_DMA | ATA_R_WRITE))) 86 request->flags &= ~ATA_R_DMA; 87 88 /* check for 48 bit access and convert if needed */ 89 ata_modify_if_48bit(request); 90 91 switch (request->flags & (ATA_R_ATAPI | ATA_R_DMA)) { 92 93 /* ATA PIO data transfer and control commands */ 94 default: 95 { 96 /* record command direction here as our request might be gone later */ 97 int write = (request->flags & ATA_R_WRITE); 98 99 /* issue command */ 100 if (ch->hw.command(request)) { 101 device_printf(request->dev, "error issuing %s command\n", 102 ata_cmd2str(request)); 103 request->result = EIO; 104 goto begin_finished; 105 } 106 107 /* device reset doesn't interrupt */ 108 if (request->u.ata.command == ATA_DEVICE_RESET) { 109 110 int timeout = 1000000; 111 do { 112 DELAY(10); 113 request->status = ATA_IDX_INB(ch, ATA_STATUS); 114 } while (request->status & ATA_S_BUSY && timeout--); 115 if (request->status & ATA_S_ERROR) 116 request->error = ATA_IDX_INB(ch, ATA_ERROR); 117 goto begin_finished; 118 } 119 120 /* if write command output the data */ 121 if (write) { 122 if (ata_wait(ch, atadev, (ATA_S_READY | ATA_S_DRQ)) < 0) { 123 device_printf(request->dev, 124 "timeout waiting for write DRQ\n"); 125 request->result = EIO; 126 goto begin_finished; 127 } 128 ata_pio_write(request, request->transfersize); 129 } 130 } 131 goto begin_continue; 132 133 /* ATA DMA data transfer commands */ 134 case ATA_R_DMA: 135 /* check sanity, setup SG list and DMA engine */ 136 if ((error = ch->dma->load(ch->dev, request->data, request->bytecount, 137 request->flags & ATA_R_READ, ch->dma->sg, 138 &dummy))) { 139 device_printf(request->dev, "setting up DMA failed\n"); 140 request->result = error; 141 goto begin_finished; 142 } 143 144 /* issue command */ 145 if (ch->hw.command(request)) { 146 device_printf(request->dev, "error issuing %s command\n", 147 ata_cmd2str(request)); 148 request->result = EIO; 149 goto begin_finished; 150 } 151 152 /* start DMA engine */ 153 if (ch->dma->start && ch->dma->start(request->dev)) { 154 device_printf(request->dev, "error starting DMA\n"); 155 request->result = EIO; 156 goto begin_finished; 157 } 158 goto begin_continue; 159 160 /* ATAPI PIO commands */ 161 case ATA_R_ATAPI: 162 /* is this just a POLL DSC command ? */ 163 if (request->u.atapi.ccb[0] == ATAPI_POLL_DSC) { 164 ATA_IDX_OUTB(ch, ATA_DRIVE, ATA_D_IBM | atadev->unit); 165 DELAY(10); 166 if (!(ATA_IDX_INB(ch, ATA_ALTSTAT) & ATA_S_DSC)) 167 request->result = EBUSY; 168 goto begin_finished; 169 } 170 171 /* start ATAPI operation */ 172 if (ch->hw.command(request)) { 173 device_printf(request->dev, "error issuing ATA PACKET command\n"); 174 request->result = EIO; 175 goto begin_finished; 176 } 177 goto begin_continue; 178 179 /* ATAPI DMA commands */ 180 case ATA_R_ATAPI|ATA_R_DMA: 181 /* is this just a POLL DSC command ? */ 182 if (request->u.atapi.ccb[0] == ATAPI_POLL_DSC) { 183 ATA_IDX_OUTB(ch, ATA_DRIVE, ATA_D_IBM | atadev->unit); 184 DELAY(10); 185 if (!(ATA_IDX_INB(ch, ATA_ALTSTAT) & ATA_S_DSC)) 186 request->result = EBUSY; 187 goto begin_finished; 188 } 189 190 /* check sanity, setup SG list and DMA engine */ 191 if ((error = ch->dma->load(ch->dev, request->data, request->bytecount, 192 request->flags & ATA_R_READ, ch->dma->sg, 193 &dummy))) { 194 device_printf(request->dev, "setting up DMA failed\n"); 195 request->result = error; 196 goto begin_finished; 197 } 198 199 /* start ATAPI operation */ 200 if (ch->hw.command(request)) { 201 device_printf(request->dev, "error issuing ATA PACKET command\n"); 202 request->result = EIO; 203 goto begin_finished; 204 } 205 206 /* start DMA engine */ 207 if (ch->dma->start && ch->dma->start(request->dev)) { 208 request->result = EIO; 209 goto begin_finished; 210 } 211 goto begin_continue; 212 } 213 /* NOT REACHED */ 214 printf("ata_begin_transaction OOPS!!!\n"); 215 216 begin_finished: 217 if (ch->dma && ch->dma->flags & ATA_DMA_LOADED) 218 ch->dma->unload(ch->dev); 219 return ATA_OP_FINISHED; 220 221 begin_continue: 222 callout_reset(&request->callout, request->timeout * hz, 223 (timeout_t*)ata_timeout, request); 224 return ATA_OP_CONTINUES; 225 } 226 227 /* must be called with ATA channel locked and state_mtx held */ 228 int 229 ata_end_transaction(struct ata_request *request) 230 { 231 struct ata_channel *ch = device_get_softc(device_get_parent(request->dev)); 232 struct ata_device *atadev = device_get_softc(request->dev); 233 int length; 234 235 ATA_DEBUG_RQ(request, "end transaction"); 236 237 /* clear interrupt and get status */ 238 request->status = ATA_IDX_INB(ch, ATA_STATUS); 239 240 switch (request->flags & (ATA_R_ATAPI | ATA_R_DMA | ATA_R_CONTROL)) { 241 242 /* ATA PIO data transfer and control commands */ 243 default: 244 245 /* on timeouts we have no data or anything so just return */ 246 if (request->flags & ATA_R_TIMEOUT) 247 goto end_finished; 248 249 /* on control commands read back registers to the request struct */ 250 if (request->flags & ATA_R_CONTROL) { 251 ch->hw.tf_read(request); 252 } 253 254 /* if we got an error we are done with the HW */ 255 if (request->status & ATA_S_ERROR) { 256 request->error = ATA_IDX_INB(ch, ATA_ERROR); 257 goto end_finished; 258 } 259 260 /* are we moving data ? */ 261 if (request->flags & (ATA_R_READ | ATA_R_WRITE)) { 262 263 /* if read data get it */ 264 if (request->flags & ATA_R_READ) { 265 int flags = ATA_S_DRQ; 266 267 if (request->u.ata.command != ATA_ATAPI_IDENTIFY) 268 flags |= ATA_S_READY; 269 if (ata_wait(ch, atadev, flags) < 0) { 270 device_printf(request->dev, 271 "timeout waiting for read DRQ\n"); 272 request->result = EIO; 273 goto end_finished; 274 } 275 ata_pio_read(request, request->transfersize); 276 } 277 278 /* update how far we've gotten */ 279 request->donecount += request->transfersize; 280 281 /* do we need a scoop more ? */ 282 if (request->bytecount > request->donecount) { 283 284 /* set this transfer size according to HW capabilities */ 285 request->transfersize = 286 min((request->bytecount - request->donecount), 287 request->transfersize); 288 289 /* if data write command, output the data */ 290 if (request->flags & ATA_R_WRITE) { 291 292 /* if we get an error here we are done with the HW */ 293 if (ata_wait(ch, atadev, (ATA_S_READY | ATA_S_DRQ)) < 0) { 294 device_printf(request->dev, 295 "timeout waiting for write DRQ\n"); 296 request->status = ATA_IDX_INB(ch, ATA_STATUS); 297 goto end_finished; 298 } 299 300 /* output data and return waiting for new interrupt */ 301 ata_pio_write(request, request->transfersize); 302 goto end_continue; 303 } 304 305 /* if data read command, return & wait for interrupt */ 306 if (request->flags & ATA_R_READ) 307 goto end_continue; 308 } 309 } 310 /* done with HW */ 311 goto end_finished; 312 313 /* ATA DMA data transfer commands */ 314 case ATA_R_DMA: 315 316 /* stop DMA engine and get status */ 317 if (ch->dma->stop) 318 request->dmastat = ch->dma->stop(request->dev); 319 320 /* did we get error or data */ 321 if (request->status & ATA_S_ERROR) 322 request->error = ATA_IDX_INB(ch, ATA_ERROR); 323 else if (request->dmastat & ATA_BMSTAT_ERROR) 324 request->status |= ATA_S_ERROR; 325 else if (!(request->flags & ATA_R_TIMEOUT)) 326 request->donecount = request->bytecount; 327 328 /* release SG list etc */ 329 ch->dma->unload(ch->dev); 330 331 /* done with HW */ 332 goto end_finished; 333 334 /* ATAPI PIO commands */ 335 case ATA_R_ATAPI: 336 length = ATA_IDX_INB(ch, ATA_CYL_LSB)|(ATA_IDX_INB(ch, ATA_CYL_MSB)<<8); 337 338 /* on timeouts we have no data or anything so just return */ 339 if (request->flags & ATA_R_TIMEOUT) 340 goto end_finished; 341 342 switch ((ATA_IDX_INB(ch, ATA_IREASON) & (ATA_I_CMD | ATA_I_IN)) | 343 (request->status & ATA_S_DRQ)) { 344 345 case ATAPI_P_CMDOUT: 346 /* this seems to be needed for some (slow) devices */ 347 DELAY(10); 348 349 if (!(request->status & ATA_S_DRQ)) { 350 device_printf(request->dev, "command interrupt without DRQ\n"); 351 request->status = ATA_S_ERROR; 352 goto end_finished; 353 } 354 ATA_IDX_OUTSW_STRM(ch, ATA_DATA, (int16_t *)request->u.atapi.ccb, 355 (atadev->param.config & 356 ATA_PROTO_MASK)== ATA_PROTO_ATAPI_12 ? 6 : 8); 357 /* return wait for interrupt */ 358 goto end_continue; 359 360 case ATAPI_P_WRITE: 361 if (request->flags & ATA_R_READ) { 362 request->status = ATA_S_ERROR; 363 device_printf(request->dev, 364 "%s trying to write on read buffer\n", 365 ata_cmd2str(request)); 366 goto end_finished; 367 break; 368 } 369 ata_pio_write(request, length); 370 request->donecount += length; 371 372 /* set next transfer size according to HW capabilities */ 373 request->transfersize = min((request->bytecount-request->donecount), 374 request->transfersize); 375 /* return wait for interrupt */ 376 goto end_continue; 377 378 case ATAPI_P_READ: 379 if (request->flags & ATA_R_WRITE) { 380 request->status = ATA_S_ERROR; 381 device_printf(request->dev, 382 "%s trying to read on write buffer\n", 383 ata_cmd2str(request)); 384 goto end_finished; 385 } 386 ata_pio_read(request, length); 387 request->donecount += length; 388 389 /* set next transfer size according to HW capabilities */ 390 request->transfersize = min((request->bytecount-request->donecount), 391 request->transfersize); 392 /* return wait for interrupt */ 393 goto end_continue; 394 395 case ATAPI_P_DONEDRQ: 396 device_printf(request->dev, 397 "WARNING - %s DONEDRQ non conformant device\n", 398 ata_cmd2str(request)); 399 if (request->flags & ATA_R_READ) { 400 ata_pio_read(request, length); 401 request->donecount += length; 402 } 403 else if (request->flags & ATA_R_WRITE) { 404 ata_pio_write(request, length); 405 request->donecount += length; 406 } 407 else 408 request->status = ATA_S_ERROR; 409 /* FALLTHROUGH */ 410 411 case ATAPI_P_ABORT: 412 case ATAPI_P_DONE: 413 if (request->status & (ATA_S_ERROR | ATA_S_DWF)) 414 request->error = ATA_IDX_INB(ch, ATA_ERROR); 415 goto end_finished; 416 417 default: 418 device_printf(request->dev, "unknown transfer phase\n"); 419 request->status = ATA_S_ERROR; 420 } 421 422 /* done with HW */ 423 goto end_finished; 424 425 /* ATAPI DMA commands */ 426 case ATA_R_ATAPI|ATA_R_DMA: 427 428 /* stop DMA engine and get status */ 429 if (ch->dma->stop) 430 request->dmastat = ch->dma->stop(request->dev); 431 432 /* did we get error or data */ 433 if (request->status & (ATA_S_ERROR | ATA_S_DWF)) 434 request->error = ATA_IDX_INB(ch, ATA_ERROR); 435 else if (request->dmastat & ATA_BMSTAT_ERROR) 436 request->status |= ATA_S_ERROR; 437 else if (!(request->flags & ATA_R_TIMEOUT)) 438 request->donecount = request->bytecount; 439 440 /* release SG list etc */ 441 ch->dma->unload(ch->dev); 442 443 /* done with HW */ 444 goto end_finished; 445 } 446 /* NOT REACHED */ 447 printf("ata_end_transaction OOPS!!\n"); 448 449 end_finished: 450 callout_stop(&request->callout); 451 return ATA_OP_FINISHED; 452 453 end_continue: 454 return ATA_OP_CONTINUES; 455 } 456 457 /* must be called with ATA channel locked and state_mtx held */ 458 void 459 ata_generic_reset(device_t dev) 460 { 461 struct ata_channel *ch = device_get_softc(dev); 462 463 u_int8_t ostat0 = 0, stat0 = 0, ostat1 = 0, stat1 = 0; 464 u_int8_t err = 0, lsb = 0, msb = 0; 465 int mask = 0, timeout; 466 467 /* do we have any signs of ATA/ATAPI HW being present ? */ 468 ATA_IDX_OUTB(ch, ATA_DRIVE, ATA_D_IBM | ATA_D_LBA | ATA_MASTER); 469 DELAY(10); 470 ostat0 = ATA_IDX_INB(ch, ATA_STATUS); 471 if ((ostat0 & 0xf8) != 0xf8 && ostat0 != 0xa5) { 472 stat0 = ATA_S_BUSY; 473 mask |= 0x01; 474 } 475 476 /* in some setups we dont want to test for a slave */ 477 if (!(ch->flags & ATA_NO_SLAVE)) { 478 ATA_IDX_OUTB(ch, ATA_DRIVE, ATA_D_IBM | ATA_D_LBA | ATA_SLAVE); 479 DELAY(10); 480 ostat1 = ATA_IDX_INB(ch, ATA_STATUS); 481 if ((ostat1 & 0xf8) != 0xf8 && ostat1 != 0xa5) { 482 stat1 = ATA_S_BUSY; 483 mask |= 0x02; 484 } 485 } 486 487 if (bootverbose) 488 device_printf(dev, "reset tp1 mask=%02x ostat0=%02x ostat1=%02x\n", 489 mask, ostat0, ostat1); 490 491 /* if nothing showed up there is no need to get any further */ 492 /* XXX SOS is that too strong?, we just might loose devices here */ 493 ch->devices = 0; 494 if (!mask) 495 return; 496 497 /* reset (both) devices on this channel */ 498 ATA_IDX_OUTB(ch, ATA_DRIVE, ATA_D_IBM | ATA_D_LBA | ATA_MASTER); 499 DELAY(10); 500 ATA_IDX_OUTB(ch, ATA_CONTROL, ATA_A_IDS | ATA_A_RESET); 501 ata_udelay(10000); 502 ATA_IDX_OUTB(ch, ATA_CONTROL, ATA_A_IDS); 503 ata_udelay(100000); 504 ATA_IDX_INB(ch, ATA_ERROR); 505 506 /* wait for BUSY to go inactive */ 507 for (timeout = 0; timeout < 310; timeout++) { 508 if ((mask & 0x01) && (stat0 & ATA_S_BUSY)) { 509 ATA_IDX_OUTB(ch, ATA_DRIVE, ATA_D_IBM | ATA_MASTER); 510 DELAY(10); 511 err = ATA_IDX_INB(ch, ATA_ERROR); 512 lsb = ATA_IDX_INB(ch, ATA_CYL_LSB); 513 msb = ATA_IDX_INB(ch, ATA_CYL_MSB); 514 stat0 = ATA_IDX_INB(ch, ATA_STATUS); 515 if (bootverbose) 516 device_printf(dev, 517 "stat0=0x%02x err=0x%02x lsb=0x%02x msb=0x%02x\n", 518 stat0, err, lsb, msb); 519 if (stat0 == err && lsb == err && msb == err && 520 timeout > (stat0 & ATA_S_BUSY ? 100 : 10)) 521 mask &= ~0x01; 522 if (!(stat0 & ATA_S_BUSY)) { 523 if ((err & 0x7f) == ATA_E_ILI) { 524 if (lsb == ATAPI_MAGIC_LSB && msb == ATAPI_MAGIC_MSB) { 525 ch->devices |= ATA_ATAPI_MASTER; 526 } 527 else if (stat0 & ATA_S_READY) { 528 ch->devices |= ATA_ATA_MASTER; 529 } 530 } 531 else if ((stat0 & 0x0f) && err == lsb && err == msb) { 532 stat0 |= ATA_S_BUSY; 533 } 534 } 535 } 536 537 if ((mask & 0x02) && (stat1 & ATA_S_BUSY) && 538 !((mask & 0x01) && (stat0 & ATA_S_BUSY))) { 539 ATA_IDX_OUTB(ch, ATA_DRIVE, ATA_D_IBM | ATA_SLAVE); 540 DELAY(10); 541 err = ATA_IDX_INB(ch, ATA_ERROR); 542 lsb = ATA_IDX_INB(ch, ATA_CYL_LSB); 543 msb = ATA_IDX_INB(ch, ATA_CYL_MSB); 544 stat1 = ATA_IDX_INB(ch, ATA_STATUS); 545 if (bootverbose) 546 device_printf(dev, 547 "stat1=0x%02x err=0x%02x lsb=0x%02x msb=0x%02x\n", 548 stat1, err, lsb, msb); 549 if (stat1 == err && lsb == err && msb == err && 550 timeout > (stat1 & ATA_S_BUSY ? 100 : 10)) 551 mask &= ~0x02; 552 if (!(stat1 & ATA_S_BUSY)) { 553 if ((err & 0x7f) == ATA_E_ILI) { 554 if (lsb == ATAPI_MAGIC_LSB && msb == ATAPI_MAGIC_MSB) { 555 ch->devices |= ATA_ATAPI_SLAVE; 556 } 557 else if (stat1 & ATA_S_READY) { 558 ch->devices |= ATA_ATA_SLAVE; 559 } 560 } 561 else if ((stat1 & 0x0f) && err == lsb && err == msb) { 562 stat1 |= ATA_S_BUSY; 563 } 564 } 565 } 566 567 if (mask == 0x00) /* nothing to wait for */ 568 break; 569 if (mask == 0x01) /* wait for master only */ 570 if (!(stat0 & ATA_S_BUSY) || (stat0 == 0xff && timeout > 10)) 571 break; 572 if (mask == 0x02) /* wait for slave only */ 573 if (!(stat1 & ATA_S_BUSY) || (stat1 == 0xff && timeout > 10)) 574 break; 575 if (mask == 0x03) { /* wait for both master & slave */ 576 if (!(stat0 & ATA_S_BUSY) && !(stat1 & ATA_S_BUSY)) 577 break; 578 if ((stat0 == 0xff) && (timeout > 20)) 579 mask &= ~0x01; 580 if ((stat1 == 0xff) && (timeout > 20)) 581 mask &= ~0x02; 582 } 583 ata_udelay(100000); 584 } 585 586 if (bootverbose) 587 device_printf(dev, "reset tp2 stat0=%02x stat1=%02x devices=0x%b\n", 588 stat0, stat1, ch->devices, 589 "\20\4ATAPI_SLAVE\3ATAPI_MASTER\2ATA_SLAVE\1ATA_MASTER"); 590 } 591 592 /* must be called with ATA channel locked and state_mtx held */ 593 int 594 ata_generic_status(device_t dev) 595 { 596 struct ata_channel *ch = device_get_softc(dev); 597 598 if (ATA_IDX_INB(ch, ATA_ALTSTAT) & ATA_S_BUSY) { 599 DELAY(100); 600 if (ATA_IDX_INB(ch, ATA_ALTSTAT) & ATA_S_BUSY) 601 return 0; 602 } 603 return 1; 604 } 605 606 static int 607 ata_wait(struct ata_channel *ch, struct ata_device *atadev, u_int8_t mask) 608 { 609 u_int8_t status; 610 int timeout = 0; 611 612 DELAY(1); 613 614 /* wait at max 1 second for device to get !BUSY */ 615 while (timeout < 1000000) { 616 status = ATA_IDX_INB(ch, ATA_ALTSTAT); 617 618 /* if drive fails status, reselect the drive and try again */ 619 if (status == 0xff) { 620 ATA_IDX_OUTB(ch, ATA_DRIVE, ATA_D_IBM | atadev->unit); 621 timeout += 1000; 622 DELAY(1000); 623 continue; 624 } 625 626 /* are we done ? */ 627 if (!(status & ATA_S_BUSY)) 628 break; 629 630 if (timeout > 1000) { 631 timeout += 1000; 632 DELAY(1000); 633 } 634 else { 635 timeout += 10; 636 DELAY(10); 637 } 638 } 639 if (timeout >= 1000000) 640 return -2; 641 if (!mask) 642 return (status & ATA_S_ERROR); 643 644 DELAY(1); 645 646 /* wait 50 msec for bits wanted */ 647 timeout = 5000; 648 while (timeout--) { 649 status = ATA_IDX_INB(ch, ATA_ALTSTAT); 650 if ((status & mask) == mask) 651 return (status & ATA_S_ERROR); 652 DELAY(10); 653 } 654 return -3; 655 } 656 657 int 658 ata_generic_command(struct ata_request *request) 659 { 660 struct ata_channel *ch = device_get_softc(device_get_parent(request->dev)); 661 struct ata_device *atadev = device_get_softc(request->dev); 662 663 /* select device */ 664 ATA_IDX_OUTB(ch, ATA_DRIVE, ATA_D_IBM | ATA_D_LBA | atadev->unit); 665 666 /* ready to issue command ? */ 667 if (ata_wait(ch, atadev, 0) < 0) { 668 device_printf(request->dev, "timeout waiting to issue command\n"); 669 return -1; 670 } 671 672 /* enable interrupt */ 673 ATA_IDX_OUTB(ch, ATA_CONTROL, ATA_A_4BIT); 674 675 if (request->flags & ATA_R_ATAPI) { 676 int timeout = 5000; 677 678 /* issue packet command to controller */ 679 if (request->flags & ATA_R_DMA) { 680 ATA_IDX_OUTB(ch, ATA_FEATURE, ATA_F_DMA); 681 ATA_IDX_OUTB(ch, ATA_CYL_LSB, 0); 682 ATA_IDX_OUTB(ch, ATA_CYL_MSB, 0); 683 } 684 else { 685 ATA_IDX_OUTB(ch, ATA_FEATURE, 0); 686 ATA_IDX_OUTB(ch, ATA_CYL_LSB, request->transfersize); 687 ATA_IDX_OUTB(ch, ATA_CYL_MSB, request->transfersize >> 8); 688 } 689 ATA_IDX_OUTB(ch, ATA_COMMAND, ATA_PACKET_CMD); 690 691 /* command interrupt device ? just return and wait for interrupt */ 692 if ((atadev->param.config & ATA_DRQ_MASK) == ATA_DRQ_INTR) 693 return 0; 694 695 /* wait for ready to write ATAPI command block */ 696 while (timeout--) { 697 int reason = ATA_IDX_INB(ch, ATA_IREASON); 698 int status = ATA_IDX_INB(ch, ATA_STATUS); 699 700 if (((reason & (ATA_I_CMD | ATA_I_IN)) | 701 (status & (ATA_S_DRQ | ATA_S_BUSY))) == ATAPI_P_CMDOUT) 702 break; 703 DELAY(20); 704 } 705 if (timeout <= 0) { 706 device_printf(request->dev, "timeout waiting for ATAPI ready\n"); 707 request->result = EIO; 708 return -1; 709 } 710 711 /* this seems to be needed for some (slow) devices */ 712 DELAY(10); 713 714 /* output command block */ 715 ATA_IDX_OUTSW_STRM(ch, ATA_DATA, (int16_t *)request->u.atapi.ccb, 716 (atadev->param.config & ATA_PROTO_MASK) == 717 ATA_PROTO_ATAPI_12 ? 6 : 8); 718 } 719 else { 720 ch->hw.tf_write(request); 721 722 /* issue command to controller */ 723 ATA_IDX_OUTB(ch, ATA_COMMAND, request->u.ata.command); 724 } 725 return 0; 726 } 727 728 static void 729 ata_tf_read(struct ata_request *request) 730 { 731 struct ata_channel *ch = device_get_softc(device_get_parent(request->dev)); 732 struct ata_device *atadev = device_get_softc(request->dev); 733 734 if (atadev->flags & ATA_D_48BIT_ACTIVE) { 735 ATA_IDX_OUTB(ch, ATA_CONTROL, ATA_A_4BIT | ATA_A_HOB); 736 request->u.ata.count = (ATA_IDX_INB(ch, ATA_COUNT) << 8); 737 request->u.ata.lba = 738 ((u_int64_t)(ATA_IDX_INB(ch, ATA_SECTOR)) << 24) | 739 ((u_int64_t)(ATA_IDX_INB(ch, ATA_CYL_LSB)) << 32) | 740 ((u_int64_t)(ATA_IDX_INB(ch, ATA_CYL_MSB)) << 40); 741 742 ATA_IDX_OUTB(ch, ATA_CONTROL, ATA_A_4BIT); 743 request->u.ata.count |= ATA_IDX_INB(ch, ATA_COUNT); 744 request->u.ata.lba |= 745 (ATA_IDX_INB(ch, ATA_SECTOR) | 746 (ATA_IDX_INB(ch, ATA_CYL_LSB) << 8) | 747 (ATA_IDX_INB(ch, ATA_CYL_MSB) << 16)); 748 } 749 else { 750 request->u.ata.count = ATA_IDX_INB(ch, ATA_COUNT); 751 request->u.ata.lba = ATA_IDX_INB(ch, ATA_SECTOR) | 752 (ATA_IDX_INB(ch, ATA_CYL_LSB) << 8) | 753 (ATA_IDX_INB(ch, ATA_CYL_MSB) << 16) | 754 ((ATA_IDX_INB(ch, ATA_DRIVE) & 0xf) << 24); 755 } 756 } 757 758 static void 759 ata_tf_write(struct ata_request *request) 760 { 761 struct ata_channel *ch = device_get_softc(device_get_parent(request->dev)); 762 struct ata_device *atadev = device_get_softc(request->dev); 763 764 if (atadev->flags & ATA_D_48BIT_ACTIVE) { 765 ATA_IDX_OUTB(ch, ATA_FEATURE, request->u.ata.feature >> 8); 766 ATA_IDX_OUTB(ch, ATA_FEATURE, request->u.ata.feature); 767 ATA_IDX_OUTB(ch, ATA_COUNT, request->u.ata.count >> 8); 768 ATA_IDX_OUTB(ch, ATA_COUNT, request->u.ata.count); 769 ATA_IDX_OUTB(ch, ATA_SECTOR, request->u.ata.lba >> 24); 770 ATA_IDX_OUTB(ch, ATA_SECTOR, request->u.ata.lba); 771 ATA_IDX_OUTB(ch, ATA_CYL_LSB, request->u.ata.lba >> 32); 772 ATA_IDX_OUTB(ch, ATA_CYL_LSB, request->u.ata.lba >> 8); 773 ATA_IDX_OUTB(ch, ATA_CYL_MSB, request->u.ata.lba >> 40); 774 ATA_IDX_OUTB(ch, ATA_CYL_MSB, request->u.ata.lba >> 16); 775 ATA_IDX_OUTB(ch, ATA_DRIVE, ATA_D_LBA | atadev->unit); 776 } 777 else { 778 ATA_IDX_OUTB(ch, ATA_FEATURE, request->u.ata.feature); 779 ATA_IDX_OUTB(ch, ATA_COUNT, request->u.ata.count); 780 if (atadev->flags & ATA_D_USE_CHS) { 781 int heads, sectors; 782 783 if (atadev->param.atavalid & ATA_FLAG_54_58) { 784 heads = atadev->param.current_heads; 785 sectors = atadev->param.current_sectors; 786 } 787 else { 788 heads = atadev->param.heads; 789 sectors = atadev->param.sectors; 790 } 791 792 ATA_IDX_OUTB(ch, ATA_SECTOR, (request->u.ata.lba % sectors)+1); 793 ATA_IDX_OUTB(ch, ATA_CYL_LSB, 794 (request->u.ata.lba / (sectors * heads))); 795 ATA_IDX_OUTB(ch, ATA_CYL_MSB, 796 (request->u.ata.lba / (sectors * heads)) >> 8); 797 ATA_IDX_OUTB(ch, ATA_DRIVE, ATA_D_IBM | atadev->unit | 798 (((request->u.ata.lba% (sectors * heads)) / 799 sectors) & 0xf)); 800 } 801 else { 802 ATA_IDX_OUTB(ch, ATA_SECTOR, request->u.ata.lba); 803 ATA_IDX_OUTB(ch, ATA_CYL_LSB, request->u.ata.lba >> 8); 804 ATA_IDX_OUTB(ch, ATA_CYL_MSB, request->u.ata.lba >> 16); 805 ATA_IDX_OUTB(ch, ATA_DRIVE, 806 ATA_D_IBM | ATA_D_LBA | atadev->unit | 807 ((request->u.ata.lba >> 24) & 0x0f)); 808 } 809 } 810 } 811 812 static void 813 ata_pio_read(struct ata_request *request, int length) 814 { 815 struct ata_channel *ch = device_get_softc(device_get_parent(request->dev)); 816 int size = min(request->transfersize, length); 817 int resid; 818 819 if (ch->flags & ATA_USE_16BIT || (size % sizeof(int32_t))) 820 ATA_IDX_INSW_STRM(ch, ATA_DATA, 821 (void*)((uintptr_t)request->data+request->donecount), 822 size / sizeof(int16_t)); 823 else 824 ATA_IDX_INSL_STRM(ch, ATA_DATA, 825 (void*)((uintptr_t)request->data+request->donecount), 826 size / sizeof(int32_t)); 827 828 if (request->transfersize < length) { 829 device_printf(request->dev, "WARNING - %s read data overrun %d>%d\n", 830 ata_cmd2str(request), length, request->transfersize); 831 for (resid = request->transfersize; resid < length; 832 resid += sizeof(int16_t)) 833 ATA_IDX_INW(ch, ATA_DATA); 834 } 835 } 836 837 static void 838 ata_pio_write(struct ata_request *request, int length) 839 { 840 struct ata_channel *ch = device_get_softc(device_get_parent(request->dev)); 841 int size = min(request->transfersize, length); 842 int resid; 843 844 if (ch->flags & ATA_USE_16BIT || (size % sizeof(int32_t))) 845 ATA_IDX_OUTSW_STRM(ch, ATA_DATA, 846 (void*)((uintptr_t)request->data+request->donecount), 847 size / sizeof(int16_t)); 848 else 849 ATA_IDX_OUTSL_STRM(ch, ATA_DATA, 850 (void*)((uintptr_t)request->data+request->donecount), 851 size / sizeof(int32_t)); 852 853 if (request->transfersize < length) { 854 device_printf(request->dev, "WARNING - %s write data underrun %d>%d\n", 855 ata_cmd2str(request), length, request->transfersize); 856 for (resid = request->transfersize; resid < length; 857 resid += sizeof(int16_t)) 858 ATA_IDX_OUTW(ch, ATA_DATA, 0); 859 } 860 } 861