1 /*- 2 * Interface for the 93C66/56/46/26/06 serial eeprom parts. 3 * 4 * Copyright (c) 1995, 1996 Daniel M. Eischen 5 * All rights reserved. 6 * 7 * Redistribution and use in source and binary forms, with or without 8 * modification, are permitted provided that the following conditions 9 * are met: 10 * 1. Redistributions of source code must retain the above copyright 11 * notice, this list of conditions, and the following disclaimer, 12 * without modification. 13 * 2. The name of the author may not be used to endorse or promote products 14 * derived from this software without specific prior written permission. 15 * 16 * Alternatively, this software may be distributed under the terms of the 17 * GNU General Public License ("GPL"). 18 * 19 * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND 20 * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 21 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 22 * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR 23 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 24 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 25 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 26 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT 27 * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY 28 * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF 29 * SUCH DAMAGE. 30 * 31 * $Id: //depot/aic7xxx/aic7xxx/aic7xxx_93cx6.c#19 $ 32 */ 33 34 /* 35 * The instruction set of the 93C66/56/46/26/06 chips are as follows: 36 * 37 * Start OP * 38 * Function Bit Code Address** Data Description 39 * ------------------------------------------------------------------- 40 * READ 1 10 A5 - A0 Reads data stored in memory, 41 * starting at specified address 42 * EWEN 1 00 11XXXX Write enable must precede 43 * all programming modes 44 * ERASE 1 11 A5 - A0 Erase register A5A4A3A2A1A0 45 * WRITE 1 01 A5 - A0 D15 - D0 Writes register 46 * ERAL 1 00 10XXXX Erase all registers 47 * WRAL 1 00 01XXXX D15 - D0 Writes to all registers 48 * EWDS 1 00 00XXXX Disables all programming 49 * instructions 50 * *Note: A value of X for address is a don't care condition. 51 * **Note: There are 8 address bits for the 93C56/66 chips unlike 52 * the 93C46/26/06 chips which have 6 address bits. 53 * 54 * The 93C46 has a four wire interface: clock, chip select, data in, and 55 * data out. In order to perform one of the above functions, you need 56 * to enable the chip select for a clock period (typically a minimum of 57 * 1 usec, with the clock high and low a minimum of 750 and 250 nsec 58 * respectively). While the chip select remains high, you can clock in 59 * the instructions (above) starting with the start bit, followed by the 60 * OP code, Address, and Data (if needed). For the READ instruction, the 61 * requested 16-bit register contents is read from the data out line but 62 * is preceded by an initial zero (leading 0, followed by 16-bits, MSB 63 * first). The clock cycling from low to high initiates the next data 64 * bit to be sent from the chip. 65 */ 66 67 #ifdef __linux__ 68 #include "aic7xxx_osm.h" 69 #include "aic7xxx_inline.h" 70 #include "aic7xxx_93cx6.h" 71 #else 72 #include <sys/cdefs.h> 73 __FBSDID("$FreeBSD$"); 74 #include <dev/aic7xxx/aic7xxx_osm.h> 75 #include <dev/aic7xxx/aic7xxx_inline.h> 76 #include <dev/aic7xxx/aic7xxx_93cx6.h> 77 #endif 78 79 /* 80 * Right now, we only have to read the SEEPROM. But we make it easier to 81 * add other 93Cx6 functions. 82 */ 83 struct seeprom_cmd { 84 uint8_t len; 85 uint8_t bits[11]; 86 }; 87 88 /* Short opcodes for the c46 */ 89 static struct seeprom_cmd seeprom_ewen = {9, {1, 0, 0, 1, 1, 0, 0, 0, 0}}; 90 static struct seeprom_cmd seeprom_ewds = {9, {1, 0, 0, 0, 0, 0, 0, 0, 0}}; 91 92 /* Long opcodes for the C56/C66 */ 93 static struct seeprom_cmd seeprom_long_ewen = {11, {1, 0, 0, 1, 1, 0, 0, 0, 0}}; 94 static struct seeprom_cmd seeprom_long_ewds = {11, {1, 0, 0, 0, 0, 0, 0, 0, 0}}; 95 96 /* Common opcodes */ 97 static struct seeprom_cmd seeprom_write = {3, {1, 0, 1}}; 98 static struct seeprom_cmd seeprom_read = {3, {1, 1, 0}}; 99 100 /* 101 * Wait for the SEERDY to go high; about 800 ns. 102 */ 103 #define CLOCK_PULSE(sd, rdy) \ 104 while ((SEEPROM_STATUS_INB(sd) & rdy) == 0) { \ 105 ; /* Do nothing */ \ 106 } \ 107 (void)SEEPROM_INB(sd); /* Clear clock */ 108 109 /* 110 * Send a START condition and the given command 111 */ 112 static void 113 send_seeprom_cmd(struct seeprom_descriptor *sd, struct seeprom_cmd *cmd) 114 { 115 uint8_t temp; 116 int i = 0; 117 118 /* Send chip select for one clock cycle. */ 119 temp = sd->sd_MS ^ sd->sd_CS; 120 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 121 CLOCK_PULSE(sd, sd->sd_RDY); 122 123 for (i = 0; i < cmd->len; i++) { 124 if (cmd->bits[i] != 0) 125 temp ^= sd->sd_DO; 126 SEEPROM_OUTB(sd, temp); 127 CLOCK_PULSE(sd, sd->sd_RDY); 128 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 129 CLOCK_PULSE(sd, sd->sd_RDY); 130 if (cmd->bits[i] != 0) 131 temp ^= sd->sd_DO; 132 } 133 } 134 135 /* 136 * Clear CS put the chip in the reset state, where it can wait for new commands. 137 */ 138 static void 139 reset_seeprom(struct seeprom_descriptor *sd) 140 { 141 uint8_t temp; 142 143 temp = sd->sd_MS; 144 SEEPROM_OUTB(sd, temp); 145 CLOCK_PULSE(sd, sd->sd_RDY); 146 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 147 CLOCK_PULSE(sd, sd->sd_RDY); 148 SEEPROM_OUTB(sd, temp); 149 CLOCK_PULSE(sd, sd->sd_RDY); 150 } 151 152 /* 153 * Read the serial EEPROM and returns 1 if successful and 0 if 154 * not successful. 155 */ 156 int 157 ahc_read_seeprom(struct seeprom_descriptor *sd, uint16_t *buf, 158 u_int start_addr, u_int count) 159 { 160 int i = 0; 161 u_int k = 0; 162 uint16_t v; 163 uint8_t temp; 164 165 /* 166 * Read the requested registers of the seeprom. The loop 167 * will range from 0 to count-1. 168 */ 169 for (k = start_addr; k < count + start_addr; k++) { 170 /* 171 * Now we're ready to send the read command followed by the 172 * address of the 16-bit register we want to read. 173 */ 174 send_seeprom_cmd(sd, &seeprom_read); 175 176 /* Send the 6 or 8 bit address (MSB first, LSB last). */ 177 temp = sd->sd_MS ^ sd->sd_CS; 178 for (i = (sd->sd_chip - 1); i >= 0; i--) { 179 if ((k & (1 << i)) != 0) 180 temp ^= sd->sd_DO; 181 SEEPROM_OUTB(sd, temp); 182 CLOCK_PULSE(sd, sd->sd_RDY); 183 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 184 CLOCK_PULSE(sd, sd->sd_RDY); 185 if ((k & (1 << i)) != 0) 186 temp ^= sd->sd_DO; 187 } 188 189 /* 190 * Now read the 16 bit register. An initial 0 precedes the 191 * register contents which begins with bit 15 (MSB) and ends 192 * with bit 0 (LSB). The initial 0 will be shifted off the 193 * top of our word as we let the loop run from 0 to 16. 194 */ 195 v = 0; 196 for (i = 16; i >= 0; i--) { 197 SEEPROM_OUTB(sd, temp); 198 CLOCK_PULSE(sd, sd->sd_RDY); 199 v <<= 1; 200 if (SEEPROM_DATA_INB(sd) & sd->sd_DI) 201 v |= 1; 202 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 203 CLOCK_PULSE(sd, sd->sd_RDY); 204 } 205 206 buf[k - start_addr] = v; 207 208 /* Reset the chip select for the next command cycle. */ 209 reset_seeprom(sd); 210 } 211 #ifdef AHC_DUMP_EEPROM 212 printf("\nSerial EEPROM:\n\t"); 213 for (k = 0; k < count; k = k + 1) { 214 if (((k % 8) == 0) && (k != 0)) { 215 printf ("\n\t"); 216 } 217 printf (" 0x%x", buf[k]); 218 } 219 printf ("\n"); 220 #endif 221 return (1); 222 } 223 224 /* 225 * Write the serial EEPROM and return 1 if successful and 0 if 226 * not successful. 227 */ 228 int 229 ahc_write_seeprom(struct seeprom_descriptor *sd, uint16_t *buf, 230 u_int start_addr, u_int count) 231 { 232 struct seeprom_cmd *ewen, *ewds; 233 uint16_t v; 234 uint8_t temp; 235 int i, k; 236 237 /* Place the chip into write-enable mode */ 238 if (sd->sd_chip == C46) { 239 ewen = &seeprom_ewen; 240 ewds = &seeprom_ewds; 241 } else if (sd->sd_chip == C56_66) { 242 ewen = &seeprom_long_ewen; 243 ewds = &seeprom_long_ewds; 244 } else { 245 printf("ahc_write_seeprom: unsupported seeprom type %d\n", 246 sd->sd_chip); 247 return (0); 248 } 249 250 send_seeprom_cmd(sd, ewen); 251 reset_seeprom(sd); 252 253 /* Write all requested data out to the seeprom. */ 254 temp = sd->sd_MS ^ sd->sd_CS; 255 for (k = start_addr; k < count + start_addr; k++) { 256 /* Send the write command */ 257 send_seeprom_cmd(sd, &seeprom_write); 258 259 /* Send the 6 or 8 bit address (MSB first). */ 260 for (i = (sd->sd_chip - 1); i >= 0; i--) { 261 if ((k & (1 << i)) != 0) 262 temp ^= sd->sd_DO; 263 SEEPROM_OUTB(sd, temp); 264 CLOCK_PULSE(sd, sd->sd_RDY); 265 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 266 CLOCK_PULSE(sd, sd->sd_RDY); 267 if ((k & (1 << i)) != 0) 268 temp ^= sd->sd_DO; 269 } 270 271 /* Write the 16 bit value, MSB first */ 272 v = buf[k - start_addr]; 273 for (i = 15; i >= 0; i--) { 274 if ((v & (1 << i)) != 0) 275 temp ^= sd->sd_DO; 276 SEEPROM_OUTB(sd, temp); 277 CLOCK_PULSE(sd, sd->sd_RDY); 278 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 279 CLOCK_PULSE(sd, sd->sd_RDY); 280 if ((v & (1 << i)) != 0) 281 temp ^= sd->sd_DO; 282 } 283 284 /* Wait for the chip to complete the write */ 285 temp = sd->sd_MS; 286 SEEPROM_OUTB(sd, temp); 287 CLOCK_PULSE(sd, sd->sd_RDY); 288 temp = sd->sd_MS ^ sd->sd_CS; 289 do { 290 SEEPROM_OUTB(sd, temp); 291 CLOCK_PULSE(sd, sd->sd_RDY); 292 SEEPROM_OUTB(sd, temp ^ sd->sd_CK); 293 CLOCK_PULSE(sd, sd->sd_RDY); 294 } while ((SEEPROM_DATA_INB(sd) & sd->sd_DI) == 0); 295 296 reset_seeprom(sd); 297 } 298 299 /* Put the chip back into write-protect mode */ 300 send_seeprom_cmd(sd, ewds); 301 reset_seeprom(sd); 302 303 return (1); 304 } 305 306 int 307 ahc_verify_cksum(struct seeprom_config *sc) 308 { 309 int i; 310 int maxaddr; 311 uint32_t checksum; 312 uint16_t *scarray; 313 314 maxaddr = (sizeof(*sc)/2) - 1; 315 checksum = 0; 316 scarray = (uint16_t *)sc; 317 318 for (i = 0; i < maxaddr; i++) 319 checksum = checksum + scarray[i]; 320 if (checksum == 0 321 || (checksum & 0xFFFF) != sc->checksum) { 322 return (0); 323 } else { 324 return(1); 325 } 326 } 327