1 /*- 2 * Product specific probe and attach routines for: 3 * aic7901 and aic7902 SCSI controllers 4 * 5 * Copyright (c) 1994-2001 Justin T. Gibbs. 6 * Copyright (c) 2000-2002 Adaptec Inc. 7 * All rights reserved. 8 * 9 * Redistribution and use in source and binary forms, with or without 10 * modification, are permitted provided that the following conditions 11 * are met: 12 * 1. Redistributions of source code must retain the above copyright 13 * notice, this list of conditions, and the following disclaimer, 14 * without modification. 15 * 2. Redistributions in binary form must reproduce at minimum a disclaimer 16 * substantially similar to the "NO WARRANTY" disclaimer below 17 * ("Disclaimer") and any redistribution must be conditioned upon 18 * including a substantially similar Disclaimer requirement for further 19 * binary redistribution. 20 * 3. Neither the names of the above-listed copyright holders nor the names 21 * of any contributors may be used to endorse or promote products derived 22 * from this software without specific prior written permission. 23 * 24 * Alternatively, this software may be distributed under the terms of the 25 * GNU General Public License ("GPL") version 2 as published by the Free 26 * Software Foundation. 27 * 28 * NO WARRANTY 29 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS 30 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 31 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR 32 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT 33 * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 34 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS 35 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) 36 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, 37 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING 38 * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE 39 * POSSIBILITY OF SUCH DAMAGES. 40 * 41 * $Id: //depot/aic7xxx/aic7xxx/aic79xx_pci.c#88 $ 42 */ 43 44 #ifdef __linux__ 45 #include "aic79xx_osm.h" 46 #include "aic79xx_inline.h" 47 #else 48 #include <sys/cdefs.h> 49 __FBSDID("$FreeBSD$"); 50 #include <dev/aic7xxx/aic79xx_osm.h> 51 #include <dev/aic7xxx/aic79xx_inline.h> 52 #endif 53 54 static __inline uint64_t 55 ahd_compose_id(u_int device, u_int vendor, u_int subdevice, u_int subvendor) 56 { 57 uint64_t id; 58 59 id = subvendor 60 | (subdevice << 16) 61 | ((uint64_t)vendor << 32) 62 | ((uint64_t)device << 48); 63 64 return (id); 65 } 66 67 #define ID_ALL_MASK 0xFFFFFFFFFFFFFFFFull 68 #define ID_ALL_IROC_MASK 0xFF7FFFFFFFFFFFFFull 69 #define ID_DEV_VENDOR_MASK 0xFFFFFFFF00000000ull 70 #define ID_9005_GENERIC_MASK 0xFFF0FFFF00000000ull 71 #define ID_9005_GENERIC_IROC_MASK 0xFF70FFFF00000000ull 72 73 #define ID_AIC7901 0x800F9005FFFF9005ull 74 #define ID_AHA_29320A 0x8000900500609005ull 75 #define ID_AHA_29320ALP 0x8017900500449005ull 76 77 #define ID_AIC7901A 0x801E9005FFFF9005ull 78 #define ID_AHA_29320LP 0x8014900500449005ull 79 80 #define ID_AIC7902 0x801F9005FFFF9005ull 81 #define ID_AIC7902_B 0x801D9005FFFF9005ull 82 #define ID_AHA_39320 0x8010900500409005ull 83 #define ID_AHA_29320 0x8012900500429005ull 84 #define ID_AHA_29320B 0x8013900500439005ull 85 #define ID_AHA_39320_B 0x8015900500409005ull 86 #define ID_AHA_39320_B_DELL 0x8015900501681028ull 87 #define ID_AHA_39320A 0x8016900500409005ull 88 #define ID_AHA_39320D 0x8011900500419005ull 89 #define ID_AHA_39320D_B 0x801C900500419005ull 90 #define ID_AHA_39320D_HP 0x8011900500AC0E11ull 91 #define ID_AHA_39320D_B_HP 0x801C900500AC0E11ull 92 #define ID_AIC7902_PCI_REV_A4 0x3 93 #define ID_AIC7902_PCI_REV_B0 0x10 94 #define SUBID_HP 0x0E11 95 96 #define DEVID_9005_HOSTRAID(id) ((id) & 0x80) 97 98 #define DEVID_9005_TYPE(id) ((id) & 0xF) 99 #define DEVID_9005_TYPE_HBA 0x0 /* Standard Card */ 100 #define DEVID_9005_TYPE_HBA_2EXT 0x1 /* 2 External Ports */ 101 #define DEVID_9005_TYPE_MB 0xF /* On Motherboard */ 102 103 #define DEVID_9005_MFUNC(id) ((id) & 0x10) 104 105 #define DEVID_9005_PACKETIZED(id) ((id) & 0x8000) 106 107 #define SUBID_9005_TYPE(id) ((id) & 0xF) 108 #define SUBID_9005_TYPE_HBA 0x0 /* Standard Card */ 109 #define SUBID_9005_TYPE_MB 0xF /* On Motherboard */ 110 111 #define SUBID_9005_AUTOTERM(id) (((id) & 0x10) == 0) 112 113 #define SUBID_9005_LEGACYCONN_FUNC(id) ((id) & 0x20) 114 115 #define SUBID_9005_SEEPTYPE(id) ((id) & 0x0C0) >> 6) 116 #define SUBID_9005_SEEPTYPE_NONE 0x0 117 #define SUBID_9005_SEEPTYPE_4K 0x1 118 119 static ahd_device_setup_t ahd_aic7901_setup; 120 static ahd_device_setup_t ahd_aic7901A_setup; 121 static ahd_device_setup_t ahd_aic7902_setup; 122 static ahd_device_setup_t ahd_aic790X_setup; 123 124 struct ahd_pci_identity ahd_pci_ident_table [] = 125 { 126 /* aic7901 based controllers */ 127 { 128 ID_AHA_29320A, 129 ID_ALL_MASK, 130 "Adaptec 29320A Ultra320 SCSI adapter", 131 ahd_aic7901_setup 132 }, 133 { 134 ID_AHA_29320ALP, 135 ID_ALL_MASK, 136 "Adaptec 29320ALP Ultra320 SCSI adapter", 137 ahd_aic7901_setup 138 }, 139 /* aic7901A based controllers */ 140 { 141 ID_AHA_29320LP, 142 ID_ALL_MASK, 143 "Adaptec 29320LP Ultra320 SCSI adapter", 144 ahd_aic7901A_setup 145 }, 146 /* aic7902 based controllers */ 147 { 148 ID_AHA_29320, 149 ID_ALL_MASK, 150 "Adaptec 29320 Ultra320 SCSI adapter", 151 ahd_aic7902_setup 152 }, 153 { 154 ID_AHA_29320B, 155 ID_ALL_MASK, 156 "Adaptec 29320B Ultra320 SCSI adapter", 157 ahd_aic7902_setup 158 }, 159 { 160 ID_AHA_39320, 161 ID_ALL_MASK, 162 "Adaptec 39320 Ultra320 SCSI adapter", 163 ahd_aic7902_setup 164 }, 165 { 166 ID_AHA_39320_B, 167 ID_ALL_MASK, 168 "Adaptec 39320 Ultra320 SCSI adapter", 169 ahd_aic7902_setup 170 }, 171 { 172 ID_AHA_39320_B_DELL, 173 ID_ALL_MASK, 174 "Adaptec (Dell OEM) 39320 Ultra320 SCSI adapter", 175 ahd_aic7902_setup 176 }, 177 { 178 ID_AHA_39320A, 179 ID_ALL_MASK, 180 "Adaptec 39320A Ultra320 SCSI adapter", 181 ahd_aic7902_setup 182 }, 183 { 184 ID_AHA_39320D, 185 ID_ALL_MASK, 186 "Adaptec 39320D Ultra320 SCSI adapter", 187 ahd_aic7902_setup 188 }, 189 { 190 ID_AHA_39320D_HP, 191 ID_ALL_MASK, 192 "Adaptec (HP OEM) 39320D Ultra320 SCSI adapter", 193 ahd_aic7902_setup 194 }, 195 { 196 ID_AHA_39320D_B, 197 ID_ALL_MASK, 198 "Adaptec 39320D Ultra320 SCSI adapter", 199 ahd_aic7902_setup 200 }, 201 { 202 ID_AHA_39320D_B_HP, 203 ID_ALL_MASK, 204 "Adaptec (HP OEM) 39320D Ultra320 SCSI adapter", 205 ahd_aic7902_setup 206 }, 207 /* Generic chip probes for devices we don't know 'exactly' */ 208 { 209 ID_AIC7901 & ID_9005_GENERIC_MASK, 210 ID_9005_GENERIC_MASK, 211 "Adaptec AIC7901 Ultra320 SCSI adapter", 212 ahd_aic7901_setup 213 }, 214 { 215 ID_AIC7901A & ID_DEV_VENDOR_MASK, 216 ID_DEV_VENDOR_MASK, 217 "Adaptec AIC7901A Ultra320 SCSI adapter", 218 ahd_aic7901A_setup 219 }, 220 { 221 ID_AIC7902 & ID_9005_GENERIC_MASK, 222 ID_9005_GENERIC_MASK, 223 "Adaptec AIC7902 Ultra320 SCSI adapter", 224 ahd_aic7902_setup 225 } 226 }; 227 228 const u_int ahd_num_pci_devs = NUM_ELEMENTS(ahd_pci_ident_table); 229 230 #define DEVCONFIG 0x40 231 #define PCIXINITPAT 0x0000E000ul 232 #define PCIXINIT_PCI33_66 0x0000E000ul 233 #define PCIXINIT_PCIX50_66 0x0000C000ul 234 #define PCIXINIT_PCIX66_100 0x0000A000ul 235 #define PCIXINIT_PCIX100_133 0x00008000ul 236 #define PCI_BUS_MODES_INDEX(devconfig) \ 237 (((devconfig) & PCIXINITPAT) >> 13) 238 static const char *pci_bus_modes[] = 239 { 240 "PCI bus mode unknown", 241 "PCI bus mode unknown", 242 "PCI bus mode unknown", 243 "PCI bus mode unknown", 244 "PCI-X 101-133Mhz", 245 "PCI-X 67-100Mhz", 246 "PCI-X 50-66Mhz", 247 "PCI 33 or 66Mhz" 248 }; 249 250 #define TESTMODE 0x00000800ul 251 #define IRDY_RST 0x00000200ul 252 #define FRAME_RST 0x00000100ul 253 #define PCI64BIT 0x00000080ul 254 #define MRDCEN 0x00000040ul 255 #define ENDIANSEL 0x00000020ul 256 #define MIXQWENDIANEN 0x00000008ul 257 #define DACEN 0x00000004ul 258 #define STPWLEVEL 0x00000002ul 259 #define QWENDIANSEL 0x00000001ul 260 261 #define DEVCONFIG1 0x44 262 #define PREQDIS 0x01 263 264 #define CSIZE_LATTIME 0x0c 265 #define CACHESIZE 0x000000fful 266 #define LATTIME 0x0000ff00ul 267 268 static int ahd_check_extport(struct ahd_softc *ahd); 269 static void ahd_configure_termination(struct ahd_softc *ahd, 270 u_int adapter_control); 271 static void ahd_pci_split_intr(struct ahd_softc *ahd, u_int intstat); 272 273 struct ahd_pci_identity * 274 ahd_find_pci_device(aic_dev_softc_t pci) 275 { 276 uint64_t full_id; 277 uint16_t device; 278 uint16_t vendor; 279 uint16_t subdevice; 280 uint16_t subvendor; 281 struct ahd_pci_identity *entry; 282 u_int i; 283 284 vendor = aic_pci_read_config(pci, PCIR_DEVVENDOR, /*bytes*/2); 285 device = aic_pci_read_config(pci, PCIR_DEVICE, /*bytes*/2); 286 subvendor = aic_pci_read_config(pci, PCIR_SUBVEND_0, /*bytes*/2); 287 subdevice = aic_pci_read_config(pci, PCIR_SUBDEV_0, /*bytes*/2); 288 full_id = ahd_compose_id(device, 289 vendor, 290 subdevice, 291 subvendor); 292 293 /* 294 * If we are configured to attach to HostRAID 295 * controllers, mask out the IROC/HostRAID bit 296 * in the 297 */ 298 if (ahd_attach_to_HostRAID_controllers) 299 full_id &= ID_ALL_IROC_MASK; 300 301 for (i = 0; i < ahd_num_pci_devs; i++) { 302 entry = &ahd_pci_ident_table[i]; 303 if (entry->full_id == (full_id & entry->id_mask)) { 304 /* Honor exclusion entries. */ 305 if (entry->name == NULL) 306 return (NULL); 307 return (entry); 308 } 309 } 310 return (NULL); 311 } 312 313 int 314 ahd_pci_config(struct ahd_softc *ahd, struct ahd_pci_identity *entry) 315 { 316 struct scb_data *shared_scb_data; 317 u_int command; 318 uint32_t devconfig; 319 uint16_t device; 320 uint16_t subvendor; 321 int error; 322 323 shared_scb_data = NULL; 324 ahd->description = entry->name; 325 /* 326 * Record if this is a HostRAID board. 327 */ 328 device = aic_pci_read_config(ahd->dev_softc, 329 PCIR_DEVICE, /*bytes*/2); 330 if (DEVID_9005_HOSTRAID(device)) 331 ahd->flags |= AHD_HOSTRAID_BOARD; 332 333 /* 334 * Record if this is an HP board. 335 */ 336 subvendor = aic_pci_read_config(ahd->dev_softc, 337 PCIR_SUBVEND_0, /*bytes*/2); 338 if (subvendor == SUBID_HP) 339 ahd->flags |= AHD_HP_BOARD; 340 341 error = entry->setup(ahd); 342 if (error != 0) 343 return (error); 344 345 /* 346 * Find the PCI-X cap pointer. If we don't find it, 347 * pcix_ptr will be 0. 348 */ 349 pci_find_extcap(ahd->dev_softc, PCIY_PCIX, &ahd->pcix_ptr); 350 devconfig = aic_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4); 351 if ((devconfig & PCIXINITPAT) == PCIXINIT_PCI33_66) { 352 ahd->chip |= AHD_PCI; 353 /* Disable PCIX workarounds when running in PCI mode. */ 354 ahd->bugs &= ~AHD_PCIX_BUG_MASK; 355 } else { 356 ahd->chip |= AHD_PCIX; 357 if (ahd->pcix_ptr == 0) 358 return (ENXIO); 359 } 360 ahd->bus_description = pci_bus_modes[PCI_BUS_MODES_INDEX(devconfig)]; 361 362 aic_power_state_change(ahd, AIC_POWER_STATE_D0); 363 364 error = ahd_pci_map_registers(ahd); 365 if (error != 0) 366 return (error); 367 368 /* 369 * If we need to support high memory, enable dual 370 * address cycles. This bit must be set to enable 371 * high address bit generation even if we are on a 372 * 64bit bus (PCI64BIT set in devconfig). 373 */ 374 if ((ahd->flags & (AHD_39BIT_ADDRESSING|AHD_64BIT_ADDRESSING)) != 0) { 375 uint32_t devconfig; 376 377 if (bootverbose) 378 printf("%s: Enabling 39Bit Addressing\n", 379 ahd_name(ahd)); 380 devconfig = aic_pci_read_config(ahd->dev_softc, 381 DEVCONFIG, /*bytes*/4); 382 devconfig |= DACEN; 383 aic_pci_write_config(ahd->dev_softc, DEVCONFIG, 384 devconfig, /*bytes*/4); 385 } 386 387 /* Ensure busmastering is enabled */ 388 command = aic_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2); 389 command |= PCIM_CMD_BUSMASTEREN; 390 aic_pci_write_config(ahd->dev_softc, PCIR_COMMAND, command, /*bytes*/2); 391 392 error = ahd_softc_init(ahd); 393 if (error != 0) 394 return (error); 395 396 ahd->bus_intr = ahd_pci_intr; 397 398 error = ahd_reset(ahd, /*reinit*/FALSE); 399 if (error != 0) 400 return (ENXIO); 401 402 ahd->pci_cachesize = 403 aic_pci_read_config(ahd->dev_softc, CSIZE_LATTIME, 404 /*bytes*/1) & CACHESIZE; 405 ahd->pci_cachesize *= 4; 406 407 ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); 408 /* See if we have a SEEPROM and perform auto-term */ 409 error = ahd_check_extport(ahd); 410 if (error != 0) 411 return (error); 412 413 /* Core initialization */ 414 error = ahd_init(ahd); 415 if (error != 0) 416 return (error); 417 418 /* 419 * Allow interrupts now that we are completely setup. 420 */ 421 error = ahd_pci_map_int(ahd); 422 if (error != 0) 423 return (error); 424 425 ahd_lock(ahd); 426 /* 427 * Link this softc in with all other ahd instances. 428 */ 429 ahd_softc_insert(ahd); 430 ahd_unlock(ahd); 431 return (0); 432 } 433 434 /* 435 * Perform some simple tests that should catch situations where 436 * our registers are invalidly mapped. 437 */ 438 int 439 ahd_pci_test_register_access(struct ahd_softc *ahd) 440 { 441 uint32_t cmd; 442 u_int targpcistat; 443 u_int pci_status1; 444 int error; 445 uint8_t hcntrl; 446 447 error = EIO; 448 449 /* 450 * Enable PCI error interrupt status, but suppress NMIs 451 * generated by SERR raised due to target aborts. 452 */ 453 cmd = aic_pci_read_config(ahd->dev_softc, PCIR_COMMAND, /*bytes*/2); 454 aic_pci_write_config(ahd->dev_softc, PCIR_COMMAND, 455 cmd & ~PCIM_CMD_SERRESPEN, /*bytes*/2); 456 457 /* 458 * First a simple test to see if any 459 * registers can be read. Reading 460 * HCNTRL has no side effects and has 461 * at least one bit that is guaranteed to 462 * be zero so it is a good register to 463 * use for this test. 464 */ 465 hcntrl = ahd_inb(ahd, HCNTRL); 466 if (hcntrl == 0xFF) 467 goto fail; 468 469 /* 470 * Next create a situation where write combining 471 * or read prefetching could be initiated by the 472 * CPU or host bridge. Our device does not support 473 * either, so look for data corruption and/or flaged 474 * PCI errors. First pause without causing another 475 * chip reset. 476 */ 477 hcntrl &= ~CHIPRST; 478 ahd_outb(ahd, HCNTRL, hcntrl|PAUSE); 479 while (ahd_is_paused(ahd) == 0) 480 ; 481 482 /* Clear any PCI errors that occurred before our driver attached. */ 483 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 484 targpcistat = ahd_inb(ahd, TARGPCISTAT); 485 ahd_outb(ahd, TARGPCISTAT, targpcistat); 486 pci_status1 = aic_pci_read_config(ahd->dev_softc, 487 PCIR_STATUS + 1, /*bytes*/1); 488 aic_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, 489 pci_status1, /*bytes*/1); 490 ahd_set_modes(ahd, AHD_MODE_SCSI, AHD_MODE_SCSI); 491 ahd_outb(ahd, CLRINT, CLRPCIINT); 492 493 ahd_outb(ahd, SEQCTL0, PERRORDIS); 494 ahd_outl(ahd, SRAM_BASE, 0x5aa555aa); 495 if (ahd_inl(ahd, SRAM_BASE) != 0x5aa555aa) 496 goto fail; 497 498 if ((ahd_inb(ahd, INTSTAT) & PCIINT) != 0) { 499 u_int targpcistat; 500 501 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 502 targpcistat = ahd_inb(ahd, TARGPCISTAT); 503 if ((targpcistat & STA) != 0) 504 goto fail; 505 } 506 507 error = 0; 508 509 fail: 510 if ((ahd_inb(ahd, INTSTAT) & PCIINT) != 0) { 511 512 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 513 targpcistat = ahd_inb(ahd, TARGPCISTAT); 514 515 /* Silently clear any latched errors. */ 516 ahd_outb(ahd, TARGPCISTAT, targpcistat); 517 pci_status1 = aic_pci_read_config(ahd->dev_softc, 518 PCIR_STATUS + 1, /*bytes*/1); 519 aic_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, 520 pci_status1, /*bytes*/1); 521 ahd_outb(ahd, CLRINT, CLRPCIINT); 522 } 523 ahd_outb(ahd, SEQCTL0, PERRORDIS|FAILDIS); 524 aic_pci_write_config(ahd->dev_softc, PCIR_COMMAND, cmd, /*bytes*/2); 525 return (error); 526 } 527 528 /* 529 * Check the external port logic for a serial eeprom 530 * and termination/cable detection contrls. 531 */ 532 static int 533 ahd_check_extport(struct ahd_softc *ahd) 534 { 535 struct vpd_config vpd; 536 struct seeprom_config *sc; 537 u_int adapter_control; 538 int have_seeprom; 539 int error; 540 541 sc = ahd->seep_config; 542 have_seeprom = ahd_acquire_seeprom(ahd); 543 if (have_seeprom) { 544 u_int start_addr; 545 546 /* 547 * Fetch VPD for this function and parse it. 548 */ 549 if (bootverbose) 550 printf("%s: Reading VPD from SEEPROM...", 551 ahd_name(ahd)); 552 553 /* Address is always in units of 16bit words */ 554 start_addr = ((2 * sizeof(*sc)) 555 + (sizeof(vpd) * (ahd->channel - 'A'))) / 2; 556 557 error = ahd_read_seeprom(ahd, (uint16_t *)&vpd, 558 start_addr, sizeof(vpd)/2, 559 /*bytestream*/TRUE); 560 if (error == 0) 561 error = ahd_parse_vpddata(ahd, &vpd); 562 if (bootverbose) 563 printf("%s: VPD parsing %s\n", 564 ahd_name(ahd), 565 error == 0 ? "successful" : "failed"); 566 567 if (bootverbose) 568 printf("%s: Reading SEEPROM...", ahd_name(ahd)); 569 570 /* Address is always in units of 16bit words */ 571 start_addr = (sizeof(*sc) / 2) * (ahd->channel - 'A'); 572 573 error = ahd_read_seeprom(ahd, (uint16_t *)sc, 574 start_addr, sizeof(*sc)/2, 575 /*bytestream*/FALSE); 576 577 if (error != 0) { 578 printf("Unable to read SEEPROM\n"); 579 have_seeprom = 0; 580 } else { 581 have_seeprom = ahd_verify_cksum(sc); 582 583 if (bootverbose) { 584 if (have_seeprom == 0) 585 printf ("checksum error\n"); 586 else 587 printf ("done.\n"); 588 } 589 } 590 ahd_release_seeprom(ahd); 591 } 592 593 if (!have_seeprom) { 594 u_int nvram_scb; 595 596 /* 597 * Pull scratch ram settings and treat them as 598 * if they are the contents of an seeprom if 599 * the 'ADPT', 'BIOS', or 'ASPI' signature is found 600 * in SCB 0xFF. We manually compose the data as 16bit 601 * values to avoid endian issues. 602 */ 603 ahd_set_scbptr(ahd, 0xFF); 604 nvram_scb = ahd_inb_scbram(ahd, SCB_BASE + NVRAM_SCB_OFFSET); 605 if (nvram_scb != 0xFF 606 && ((ahd_inb_scbram(ahd, SCB_BASE + 0) == 'A' 607 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'D' 608 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'P' 609 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'T') 610 || (ahd_inb_scbram(ahd, SCB_BASE + 0) == 'B' 611 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'I' 612 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'O' 613 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'S') 614 || (ahd_inb_scbram(ahd, SCB_BASE + 0) == 'A' 615 && ahd_inb_scbram(ahd, SCB_BASE + 1) == 'S' 616 && ahd_inb_scbram(ahd, SCB_BASE + 2) == 'P' 617 && ahd_inb_scbram(ahd, SCB_BASE + 3) == 'I'))) { 618 uint16_t *sc_data; 619 int i; 620 621 ahd_set_scbptr(ahd, nvram_scb); 622 sc_data = (uint16_t *)sc; 623 for (i = 0; i < 64; i += 2) 624 *sc_data++ = ahd_inw_scbram(ahd, SCB_BASE+i); 625 have_seeprom = ahd_verify_cksum(sc); 626 if (have_seeprom) 627 ahd->flags |= AHD_SCB_CONFIG_USED; 628 } 629 } 630 631 #ifdef AHD_DEBUG 632 if (have_seeprom != 0 633 && (ahd_debug & AHD_DUMP_SEEPROM) != 0) { 634 uint16_t *sc_data; 635 int i; 636 637 printf("%s: Seeprom Contents:", ahd_name(ahd)); 638 sc_data = (uint16_t *)sc; 639 for (i = 0; i < (sizeof(*sc)); i += 2) 640 printf("\n\t0x%.4x", sc_data[i]); 641 printf("\n"); 642 } 643 #endif 644 645 if (!have_seeprom) { 646 if (bootverbose) 647 printf("%s: No SEEPROM available.\n", ahd_name(ahd)); 648 ahd->flags |= AHD_USEDEFAULTS; 649 error = ahd_default_config(ahd); 650 adapter_control = CFAUTOTERM|CFSEAUTOTERM; 651 free(ahd->seep_config, M_DEVBUF); 652 ahd->seep_config = NULL; 653 } else { 654 error = ahd_parse_cfgdata(ahd, sc); 655 adapter_control = sc->adapter_control; 656 } 657 if (error != 0) 658 return (error); 659 660 ahd_configure_termination(ahd, adapter_control); 661 662 return (0); 663 } 664 665 static void 666 ahd_configure_termination(struct ahd_softc *ahd, u_int adapter_control) 667 { 668 int error; 669 u_int sxfrctl1; 670 uint8_t termctl; 671 uint32_t devconfig; 672 673 devconfig = aic_pci_read_config(ahd->dev_softc, DEVCONFIG, /*bytes*/4); 674 devconfig &= ~STPWLEVEL; 675 if ((ahd->flags & AHD_STPWLEVEL_A) != 0) 676 devconfig |= STPWLEVEL; 677 if (bootverbose) 678 printf("%s: STPWLEVEL is %s\n", 679 ahd_name(ahd), (devconfig & STPWLEVEL) ? "on" : "off"); 680 aic_pci_write_config(ahd->dev_softc, DEVCONFIG, devconfig, /*bytes*/4); 681 682 /* Make sure current sensing is off. */ 683 if ((ahd->flags & AHD_CURRENT_SENSING) != 0) { 684 (void)ahd_write_flexport(ahd, FLXADDR_ROMSTAT_CURSENSECTL, 0); 685 } 686 687 /* 688 * Read to sense. Write to set. 689 */ 690 error = ahd_read_flexport(ahd, FLXADDR_TERMCTL, &termctl); 691 if ((adapter_control & CFAUTOTERM) == 0) { 692 if (bootverbose) 693 printf("%s: Manual Primary Termination\n", 694 ahd_name(ahd)); 695 termctl &= ~(FLX_TERMCTL_ENPRILOW|FLX_TERMCTL_ENPRIHIGH); 696 if ((adapter_control & CFSTERM) != 0) 697 termctl |= FLX_TERMCTL_ENPRILOW; 698 if ((adapter_control & CFWSTERM) != 0) 699 termctl |= FLX_TERMCTL_ENPRIHIGH; 700 } else if (error != 0) { 701 printf("%s: Primary Auto-Term Sensing failed! " 702 "Using Defaults.\n", ahd_name(ahd)); 703 termctl = FLX_TERMCTL_ENPRILOW|FLX_TERMCTL_ENPRIHIGH; 704 } 705 706 if ((adapter_control & CFSEAUTOTERM) == 0) { 707 if (bootverbose) 708 printf("%s: Manual Secondary Termination\n", 709 ahd_name(ahd)); 710 termctl &= ~(FLX_TERMCTL_ENSECLOW|FLX_TERMCTL_ENSECHIGH); 711 if ((adapter_control & CFSELOWTERM) != 0) 712 termctl |= FLX_TERMCTL_ENSECLOW; 713 if ((adapter_control & CFSEHIGHTERM) != 0) 714 termctl |= FLX_TERMCTL_ENSECHIGH; 715 } else if (error != 0) { 716 printf("%s: Secondary Auto-Term Sensing failed! " 717 "Using Defaults.\n", ahd_name(ahd)); 718 termctl |= FLX_TERMCTL_ENSECLOW|FLX_TERMCTL_ENSECHIGH; 719 } 720 721 /* 722 * Now set the termination based on what we found. 723 */ 724 sxfrctl1 = ahd_inb(ahd, SXFRCTL1) & ~STPWEN; 725 ahd->flags &= ~AHD_TERM_ENB_A; 726 if ((termctl & FLX_TERMCTL_ENPRILOW) != 0) { 727 ahd->flags |= AHD_TERM_ENB_A; 728 sxfrctl1 |= STPWEN; 729 } 730 /* Must set the latch once in order to be effective. */ 731 ahd_outb(ahd, SXFRCTL1, sxfrctl1|STPWEN); 732 ahd_outb(ahd, SXFRCTL1, sxfrctl1); 733 734 error = ahd_write_flexport(ahd, FLXADDR_TERMCTL, termctl); 735 if (error != 0) { 736 printf("%s: Unable to set termination settings!\n", 737 ahd_name(ahd)); 738 } else if (bootverbose) { 739 printf("%s: Primary High byte termination %sabled\n", 740 ahd_name(ahd), 741 (termctl & FLX_TERMCTL_ENPRIHIGH) ? "En" : "Dis"); 742 743 printf("%s: Primary Low byte termination %sabled\n", 744 ahd_name(ahd), 745 (termctl & FLX_TERMCTL_ENPRILOW) ? "En" : "Dis"); 746 747 printf("%s: Secondary High byte termination %sabled\n", 748 ahd_name(ahd), 749 (termctl & FLX_TERMCTL_ENSECHIGH) ? "En" : "Dis"); 750 751 printf("%s: Secondary Low byte termination %sabled\n", 752 ahd_name(ahd), 753 (termctl & FLX_TERMCTL_ENSECLOW) ? "En" : "Dis"); 754 } 755 return; 756 } 757 758 #define DPE 0x80 759 #define SSE 0x40 760 #define RMA 0x20 761 #define RTA 0x10 762 #define STA 0x08 763 #define DPR 0x01 764 765 static const char *split_status_source[] = 766 { 767 "DFF0", 768 "DFF1", 769 "OVLY", 770 "CMC", 771 }; 772 773 static const char *pci_status_source[] = 774 { 775 "DFF0", 776 "DFF1", 777 "SG", 778 "CMC", 779 "OVLY", 780 "NONE", 781 "MSI", 782 "TARG" 783 }; 784 785 static const char *split_status_strings[] = 786 { 787 "%s: Received split response in %s.\n", 788 "%s: Received split completion error message in %s\n", 789 "%s: Receive overrun in %s\n", 790 "%s: Count not complete in %s\n", 791 "%s: Split completion data bucket in %s\n", 792 "%s: Split completion address error in %s\n", 793 "%s: Split completion byte count error in %s\n", 794 "%s: Signaled Target-abort to early terminate a split in %s\n" 795 }; 796 797 static const char *pci_status_strings[] = 798 { 799 "%s: Data Parity Error has been reported via PERR# in %s\n", 800 "%s: Target initial wait state error in %s\n", 801 "%s: Split completion read data parity error in %s\n", 802 "%s: Split completion address attribute parity error in %s\n", 803 "%s: Received a Target Abort in %s\n", 804 "%s: Received a Master Abort in %s\n", 805 "%s: Signal System Error Detected in %s\n", 806 "%s: Address or Write Phase Parity Error Detected in %s.\n" 807 }; 808 809 void 810 ahd_pci_intr(struct ahd_softc *ahd) 811 { 812 uint8_t pci_status[8]; 813 ahd_mode_state saved_modes; 814 u_int pci_status1; 815 u_int intstat; 816 u_int i; 817 u_int reg; 818 819 intstat = ahd_inb(ahd, INTSTAT); 820 821 if ((intstat & SPLTINT) != 0) 822 ahd_pci_split_intr(ahd, intstat); 823 824 if ((intstat & PCIINT) == 0) 825 return; 826 827 printf("%s: PCI error Interrupt\n", ahd_name(ahd)); 828 saved_modes = ahd_save_modes(ahd); 829 ahd_dump_card_state(ahd); 830 ahd_set_modes(ahd, AHD_MODE_CFG, AHD_MODE_CFG); 831 for (i = 0, reg = DF0PCISTAT; i < 8; i++, reg++) { 832 833 if (i == 5) 834 continue; 835 pci_status[i] = ahd_inb(ahd, reg); 836 /* Clear latched errors. So our interrupt deasserts. */ 837 ahd_outb(ahd, reg, pci_status[i]); 838 } 839 840 for (i = 0; i < 8; i++) { 841 u_int bit; 842 843 if (i == 5) 844 continue; 845 846 for (bit = 0; bit < 8; bit++) { 847 848 if ((pci_status[i] & (0x1 << bit)) != 0) { 849 static const char *s; 850 851 s = pci_status_strings[bit]; 852 if (i == 7/*TARG*/ && bit == 3) 853 s = "%s: Signaled Target Abort\n"; 854 printf(s, ahd_name(ahd), pci_status_source[i]); 855 } 856 } 857 } 858 pci_status1 = aic_pci_read_config(ahd->dev_softc, 859 PCIR_STATUS + 1, /*bytes*/1); 860 aic_pci_write_config(ahd->dev_softc, PCIR_STATUS + 1, 861 pci_status1, /*bytes*/1); 862 ahd_restore_modes(ahd, saved_modes); 863 ahd_outb(ahd, CLRINT, CLRPCIINT); 864 ahd_unpause(ahd); 865 } 866 867 static void 868 ahd_pci_split_intr(struct ahd_softc *ahd, u_int intstat) 869 { 870 uint8_t split_status[4]; 871 uint8_t split_status1[4]; 872 uint8_t sg_split_status[2]; 873 uint8_t sg_split_status1[2]; 874 ahd_mode_state saved_modes; 875 u_int i; 876 uint32_t pcix_status; 877 878 /* 879 * Check for splits in all modes. Modes 0 and 1 880 * additionally have SG engine splits to look at. 881 */ 882 pcix_status = aic_pci_read_config(ahd->dev_softc, 883 ahd->pcix_ptr + PCIXR_STATUS, /*bytes*/ 4); 884 printf("%s: PCI Split Interrupt - PCI-X status = 0x%x\n", 885 ahd_name(ahd), pcix_status >> 16); 886 saved_modes = ahd_save_modes(ahd); 887 for (i = 0; i < 4; i++) { 888 ahd_set_modes(ahd, i, i); 889 890 split_status[i] = ahd_inb(ahd, DCHSPLTSTAT0); 891 split_status1[i] = ahd_inb(ahd, DCHSPLTSTAT1); 892 /* Clear latched errors. So our interrupt deasserts. */ 893 ahd_outb(ahd, DCHSPLTSTAT0, split_status[i]); 894 ahd_outb(ahd, DCHSPLTSTAT1, split_status1[i]); 895 if (i > 1) 896 continue; 897 sg_split_status[i] = ahd_inb(ahd, SGSPLTSTAT0); 898 sg_split_status1[i] = ahd_inb(ahd, SGSPLTSTAT1); 899 /* Clear latched errors. So our interrupt deasserts. */ 900 ahd_outb(ahd, SGSPLTSTAT0, sg_split_status[i]); 901 ahd_outb(ahd, SGSPLTSTAT1, sg_split_status1[i]); 902 } 903 904 for (i = 0; i < 4; i++) { 905 u_int bit; 906 907 for (bit = 0; bit < 8; bit++) { 908 909 if ((split_status[i] & (0x1 << bit)) != 0) { 910 static const char *s; 911 912 s = split_status_strings[bit]; 913 printf(s, ahd_name(ahd), 914 split_status_source[i]); 915 } 916 917 if (i > 1) 918 continue; 919 920 if ((sg_split_status[i] & (0x1 << bit)) != 0) { 921 static const char *s; 922 923 s = split_status_strings[bit]; 924 printf(s, ahd_name(ahd), "SG"); 925 } 926 } 927 } 928 /* 929 * Clear PCI-X status bits. 930 */ 931 aic_pci_write_config(ahd->dev_softc, ahd->pcix_ptr + PCIXR_STATUS, 932 pcix_status, /*bytes*/4); 933 ahd_outb(ahd, CLRINT, CLRSPLTINT); 934 ahd_restore_modes(ahd, saved_modes); 935 } 936 937 static int 938 ahd_aic7901_setup(struct ahd_softc *ahd) 939 { 940 941 ahd->chip = AHD_AIC7901; 942 ahd->features = AHD_AIC7901_FE; 943 return (ahd_aic790X_setup(ahd)); 944 } 945 946 static int 947 ahd_aic7901A_setup(struct ahd_softc *ahd) 948 { 949 950 ahd->chip = AHD_AIC7901A; 951 ahd->features = AHD_AIC7901A_FE; 952 return (ahd_aic790X_setup(ahd)); 953 } 954 955 static int 956 ahd_aic7902_setup(struct ahd_softc *ahd) 957 { 958 ahd->chip = AHD_AIC7902; 959 ahd->features = AHD_AIC7902_FE; 960 return (ahd_aic790X_setup(ahd)); 961 } 962 963 static int 964 ahd_aic790X_setup(struct ahd_softc *ahd) 965 { 966 aic_dev_softc_t pci; 967 u_int rev; 968 969 pci = ahd->dev_softc; 970 rev = aic_pci_read_config(pci, PCIR_REVID, /*bytes*/1); 971 if (rev < ID_AIC7902_PCI_REV_A4) { 972 printf("%s: Unable to attach to unsupported chip revision %d\n", 973 ahd_name(ahd), rev); 974 aic_pci_write_config(pci, PCIR_COMMAND, 0, /*bytes*/2); 975 return (ENXIO); 976 } 977 ahd->channel = aic_get_pci_function(pci) + 'A'; 978 if (rev < ID_AIC7902_PCI_REV_B0) { 979 /* 980 * Enable A series workarounds. 981 */ 982 ahd->bugs |= AHD_SENT_SCB_UPDATE_BUG|AHD_ABORT_LQI_BUG 983 | AHD_PKT_BITBUCKET_BUG|AHD_LONG_SETIMO_BUG 984 | AHD_NLQICRC_DELAYED_BUG|AHD_SCSIRST_BUG 985 | AHD_LQO_ATNO_BUG|AHD_AUTOFLUSH_BUG 986 | AHD_CLRLQO_AUTOCLR_BUG|AHD_PCIX_MMAPIO_BUG 987 | AHD_PCIX_CHIPRST_BUG|AHD_PCIX_SCBRAM_RD_BUG 988 | AHD_PKTIZED_STATUS_BUG|AHD_PKT_LUN_BUG 989 | AHD_MDFF_WSCBPTR_BUG|AHD_REG_SLOW_SETTLE_BUG 990 | AHD_SET_MODE_BUG|AHD_BUSFREEREV_BUG 991 | AHD_NONPACKFIFO_BUG|AHD_PACED_NEGTABLE_BUG 992 | AHD_FAINT_LED_BUG; 993 994 /* 995 * IO Cell paramter setup. 996 */ 997 AHD_SET_PRECOMP(ahd, AHD_PRECOMP_CUTBACK_29); 998 999 if ((ahd->flags & AHD_HP_BOARD) == 0) 1000 AHD_SET_SLEWRATE(ahd, AHD_SLEWRATE_DEF_REVA); 1001 } else { 1002 u_int devconfig1; 1003 1004 ahd->features |= AHD_RTI|AHD_NEW_IOCELL_OPTS 1005 | AHD_NEW_DFCNTRL_OPTS|AHD_FAST_CDB_DELIVERY; 1006 ahd->bugs |= AHD_LQOOVERRUN_BUG|AHD_EARLY_REQ_BUG; 1007 1008 /* 1009 * Some issues have been resolved in the 7901B. 1010 */ 1011 if ((ahd->features & AHD_MULTI_FUNC) != 0) 1012 ahd->bugs |= AHD_INTCOLLISION_BUG|AHD_ABORT_LQI_BUG 1013 | AHD_BUSFREEREV_BUG; 1014 1015 /* 1016 * IO Cell paramter setup. 1017 */ 1018 AHD_SET_PRECOMP(ahd, AHD_PRECOMP_CUTBACK_29); 1019 AHD_SET_SLEWRATE(ahd, AHD_SLEWRATE_DEF_REVB); 1020 AHD_SET_AMPLITUDE(ahd, AHD_AMPLITUDE_DEF); 1021 1022 /* 1023 * Set the PREQDIS bit for H2B which disables some workaround 1024 * that doesn't work on regular PCI busses. 1025 * XXX - Find out exactly what this does from the hardware 1026 * folks! 1027 */ 1028 devconfig1 = aic_pci_read_config(pci, DEVCONFIG1, /*bytes*/1); 1029 aic_pci_write_config(pci, DEVCONFIG1, 1030 devconfig1|PREQDIS, /*bytes*/1); 1031 devconfig1 = aic_pci_read_config(pci, DEVCONFIG1, /*bytes*/1); 1032 } 1033 1034 return (0); 1035 } 1036