xref: /freebsd/sys/contrib/device-tree/src/powerpc/mpc832x_mds.dts (revision 7fdf597e96a02165cfe22ff357b857d5fa15ed8a) 
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * MPC8323E EMDS Device Tree Source
4 *
5 * Copyright 2006 Freescale Semiconductor Inc.
6 *
7
8 * To enable external serial I/O on a Freescale MPC 8323 SYS/MDS board, do
9 * this:
10 *
11 * 1) On chip U61, lift (disconnect) pins 21 (TXD) and 22 (RXD) from the board.
12 * 2) Solder a wire from U61-21 to P19A-23.  P19 is a grid of pins on the board
13 *    next to the serial ports.
14 * 3) Solder a wire from U61-22 to P19K-22.
15 *
16 * Note that there's a typo in the schematic.  The board labels the last column
17 * of pins "P19K", but in the schematic, that column is called "P19J".  So if
18 * you're going by the schematic, the pin is called "P19J-K22".
19 */
20
21/dts-v1/;
22
23/ {
24	model = "MPC8323EMDS";
25	compatible = "MPC8323EMDS", "MPC832xMDS", "MPC83xxMDS";
26	#address-cells = <1>;
27	#size-cells = <1>;
28
29	aliases {
30		ethernet0 = &enet0;
31		ethernet1 = &enet1;
32		serial0 = &serial0;
33		serial1 = &serial1;
34		pci0 = &pci0;
35	};
36
37	cpus {
38		#address-cells = <1>;
39		#size-cells = <0>;
40
41		PowerPC,8323@0 {
42			device_type = "cpu";
43			reg = <0x0>;
44			d-cache-line-size = <32>;	// 32 bytes
45			i-cache-line-size = <32>;	// 32 bytes
46			d-cache-size = <16384>;		// L1, 16K
47			i-cache-size = <16384>;		// L1, 16K
48			timebase-frequency = <0>;
49			bus-frequency = <0>;
50			clock-frequency = <0>;
51		};
52	};
53
54	memory {
55		device_type = "memory";
56		reg = <0x00000000 0x08000000>;
57	};
58
59	bcsr@f8000000 {
60		compatible = "fsl,mpc8323mds-bcsr";
61		reg = <0xf8000000 0x8000>;
62	};
63
64	soc8323@e0000000 {
65		#address-cells = <1>;
66		#size-cells = <1>;
67		device_type = "soc";
68		compatible = "simple-bus";
69		ranges = <0x0 0xe0000000 0x00100000>;
70		reg = <0xe0000000 0x00000200>;
71		bus-frequency = <132000000>;
72
73		wdt@200 {
74			device_type = "watchdog";
75			compatible = "mpc83xx_wdt";
76			reg = <0x200 0x100>;
77		};
78
79		pmc: power@b00 {
80			compatible = "fsl,mpc8323-pmc", "fsl,mpc8349-pmc";
81			reg = <0xb00 0x100 0xa00 0x100>;
82			interrupts = <80 0x8>;
83			interrupt-parent = <&ipic>;
84		};
85
86		i2c@3000 {
87			#address-cells = <1>;
88			#size-cells = <0>;
89			cell-index = <0>;
90			compatible = "fsl-i2c";
91			reg = <0x3000 0x100>;
92			interrupts = <14 0x8>;
93			interrupt-parent = <&ipic>;
94			dfsrr;
95
96			rtc@68 {
97				compatible = "dallas,ds1374";
98				reg = <0x68>;
99			};
100		};
101
102		serial0: serial@4500 {
103			cell-index = <0>;
104			device_type = "serial";
105			compatible = "fsl,ns16550", "ns16550";
106			reg = <0x4500 0x100>;
107			clock-frequency = <0>;
108			interrupts = <9 0x8>;
109			interrupt-parent = <&ipic>;
110		};
111
112		serial1: serial@4600 {
113			cell-index = <1>;
114			device_type = "serial";
115			compatible = "fsl,ns16550", "ns16550";
116			reg = <0x4600 0x100>;
117			clock-frequency = <0>;
118			interrupts = <10 0x8>;
119			interrupt-parent = <&ipic>;
120		};
121
122		dma@82a8 {
123			#address-cells = <1>;
124			#size-cells = <1>;
125			compatible = "fsl,mpc8323-dma", "fsl,elo-dma";
126			reg = <0x82a8 4>;
127			ranges = <0 0x8100 0x1a8>;
128			interrupt-parent = <&ipic>;
129			interrupts = <71 8>;
130			cell-index = <0>;
131			dma-channel@0 {
132				compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
133				reg = <0 0x80>;
134				cell-index = <0>;
135				interrupt-parent = <&ipic>;
136				interrupts = <71 8>;
137			};
138			dma-channel@80 {
139				compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
140				reg = <0x80 0x80>;
141				cell-index = <1>;
142				interrupt-parent = <&ipic>;
143				interrupts = <71 8>;
144			};
145			dma-channel@100 {
146				compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
147				reg = <0x100 0x80>;
148				cell-index = <2>;
149				interrupt-parent = <&ipic>;
150				interrupts = <71 8>;
151			};
152			dma-channel@180 {
153				compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
154				reg = <0x180 0x28>;
155				cell-index = <3>;
156				interrupt-parent = <&ipic>;
157				interrupts = <71 8>;
158			};
159		};
160
161		crypto@30000 {
162			compatible = "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
163			reg = <0x30000 0x10000>;
164			interrupts = <11 0x8>;
165			interrupt-parent = <&ipic>;
166			fsl,num-channels = <1>;
167			fsl,channel-fifo-len = <24>;
168			fsl,exec-units-mask = <0x4c>;
169			fsl,descriptor-types-mask = <0x0122003f>;
170			sleep = <&pmc 0x03000000>;
171		};
172
173		ipic: pic@700 {
174			interrupt-controller;
175			#address-cells = <0>;
176			#interrupt-cells = <2>;
177			reg = <0x700 0x100>;
178			device_type = "ipic";
179		};
180
181		par_io@1400 {
182			reg = <0x1400 0x100>;
183			device_type = "par_io";
184			num-ports = <7>;
185
186			pio3: ucc_pin@3 {
187				pio-map = <
188			/* port  pin  dir  open_drain  assignment  has_irq */
189					3  4  3  0  2  0  /* MDIO */
190					3  5  1  0  2  0  /* MDC */
191					0 13  2  0  1  0 	/* RX_CLK (CLK9) */
192					3 24  2  0  1  0 	/* TX_CLK (CLK10) */
193					1  0  1  0  1  0 	/* TxD0 */
194					1  1  1  0  1  0 	/* TxD1 */
195					1  2  1  0  1  0 	/* TxD2 */
196					1  3  1  0  1  0 	/* TxD3 */
197					1  4  2  0  1  0 	/* RxD0 */
198					1  5  2  0  1  0 	/* RxD1 */
199					1  6  2  0  1  0 	/* RxD2 */
200					1  7  2  0  1  0 	/* RxD3 */
201					1  8  2  0  1  0 	/* RX_ER */
202					1  9  1  0  1  0 	/* TX_ER */
203					1 10  2  0  1  0 	/* RX_DV */
204					1 11  2  0  1  0 	/* COL */
205					1 12  1  0  1  0 	/* TX_EN */
206					1 13  2  0  1  0>;	/* CRS */
207			};
208			pio4: ucc_pin@4 {
209				pio-map = <
210			/* port  pin  dir  open_drain  assignment  has_irq */
211					3 31  2  0  1  0 	/* RX_CLK (CLK7) */
212					3  6  2  0  1  0 	/* TX_CLK (CLK8) */
213					1 18  1  0  1  0 	/* TxD0 */
214					1 19  1  0  1  0 	/* TxD1 */
215					1 20  1  0  1  0 	/* TxD2 */
216					1 21  1  0  1  0 	/* TxD3 */
217					1 22  2  0  1  0 	/* RxD0 */
218					1 23  2  0  1  0 	/* RxD1 */
219					1 24  2  0  1  0 	/* RxD2 */
220					1 25  2  0  1  0 	/* RxD3 */
221					1 26  2  0  1  0 	/* RX_ER */
222					1 27  1  0  1  0 	/* TX_ER */
223					1 28  2  0  1  0 	/* RX_DV */
224					1 29  2  0  1  0 	/* COL */
225					1 30  1  0  1  0 	/* TX_EN */
226					1 31  2  0  1  0>;	/* CRS */
227			};
228			pio5: ucc_pin@5 {
229				pio-map = <
230				/*
231				 *    		      open       has
232				 *   port  pin  dir  drain  sel  irq
233				 */
234					2    0    1      0    2    0  /* TxD5 */
235					2    8    2      0    2    0  /* RxD5 */
236
237					2   29    2      0    0    0  /* CTS5 */
238					2   31    1      0    2    0  /* RTS5 */
239
240					2   24    2      0    0    0  /* CD */
241
242				>;
243			};
244
245		};
246	};
247
248	qe@e0100000 {
249		#address-cells = <1>;
250		#size-cells = <1>;
251		device_type = "qe";
252		compatible = "fsl,qe";
253		ranges = <0x0 0xe0100000 0x00100000>;
254		reg = <0xe0100000 0x480>;
255		brg-frequency = <0>;
256		bus-frequency = <198000000>;
257		fsl,qe-num-riscs = <1>;
258		fsl,qe-num-snums = <28>;
259
260		muram@10000 {
261			#address-cells = <1>;
262			#size-cells = <1>;
263			compatible = "fsl,qe-muram", "fsl,cpm-muram";
264			ranges = <0x0 0x00010000 0x00004000>;
265
266			data-only@0 {
267				compatible = "fsl,qe-muram-data",
268					     "fsl,cpm-muram-data";
269				reg = <0x0 0x4000>;
270			};
271		};
272
273		spi@4c0 {
274			cell-index = <0>;
275			compatible = "fsl,spi";
276			reg = <0x4c0 0x40>;
277			interrupts = <2>;
278			interrupt-parent = <&qeic>;
279			mode = "cpu";
280		};
281
282		spi@500 {
283			cell-index = <1>;
284			compatible = "fsl,spi";
285			reg = <0x500 0x40>;
286			interrupts = <1>;
287			interrupt-parent = <&qeic>;
288			mode = "cpu";
289		};
290
291		usb@6c0 {
292			compatible = "qe_udc";
293			reg = <0x6c0 0x40 0x8b00 0x100>;
294			interrupts = <11>;
295			interrupt-parent = <&qeic>;
296			mode = "slave";
297		};
298
299		enet0: ucc@2200 {
300			device_type = "network";
301			compatible = "ucc_geth";
302			cell-index = <3>;
303			reg = <0x2200 0x200>;
304			interrupts = <34>;
305			interrupt-parent = <&qeic>;
306			local-mac-address = [ 00 00 00 00 00 00 ];
307			rx-clock-name = "clk9";
308			tx-clock-name = "clk10";
309			phy-handle = <&phy3>;
310			pio-handle = <&pio3>;
311		};
312
313		enet1: ucc@3200 {
314			device_type = "network";
315			compatible = "ucc_geth";
316			cell-index = <4>;
317			reg = <0x3200 0x200>;
318			interrupts = <35>;
319			interrupt-parent = <&qeic>;
320			local-mac-address = [ 00 00 00 00 00 00 ];
321			rx-clock-name = "clk7";
322			tx-clock-name = "clk8";
323			phy-handle = <&phy4>;
324			pio-handle = <&pio4>;
325		};
326
327		ucc@2400 {
328			device_type = "serial";
329			compatible = "ucc_uart";
330			cell-index = <5>;	/* The UCC number, 1-7*/
331			port-number = <0>;	/* Which ttyQEx device */
332			soft-uart;		/* We need Soft-UART */
333			reg = <0x2400 0x200>;
334			interrupts = <40>;	/* From Table 18-12 */
335			interrupt-parent = < &qeic >;
336			/*
337			 * For Soft-UART, we need to set TX to 1X, which
338			 * means specifying separate clock sources.
339			 */
340			rx-clock-name = "brg5";
341			tx-clock-name = "brg6";
342			pio-handle = < &pio5 >;
343		};
344
345
346		mdio@2320 {
347			#address-cells = <1>;
348			#size-cells = <0>;
349			reg = <0x2320 0x18>;
350			compatible = "fsl,ucc-mdio";
351
352			phy3: ethernet-phy@3 {
353				interrupt-parent = <&ipic>;
354				interrupts = <17 0x8>;
355				reg = <0x3>;
356			};
357			phy4: ethernet-phy@4 {
358				interrupt-parent = <&ipic>;
359				interrupts = <18 0x8>;
360				reg = <0x4>;
361			};
362		};
363
364		qeic: interrupt-controller@80 {
365			interrupt-controller;
366			compatible = "fsl,qe-ic";
367			#address-cells = <0>;
368			#interrupt-cells = <1>;
369			reg = <0x80 0x80>;
370			big-endian;
371			interrupts = <32 0x8 33 0x8>; //high:32 low:33
372			interrupt-parent = <&ipic>;
373		};
374	};
375
376	pci0: pci@e0008500 {
377		interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
378		interrupt-map = <
379				/* IDSEL 0x11 AD17 */
380				 0x8800 0x0 0x0 0x1 &ipic 20 0x8
381				 0x8800 0x0 0x0 0x2 &ipic 21 0x8
382				 0x8800 0x0 0x0 0x3 &ipic 22 0x8
383				 0x8800 0x0 0x0 0x4 &ipic 23 0x8
384
385				/* IDSEL 0x12 AD18 */
386				 0x9000 0x0 0x0 0x1 &ipic 22 0x8
387				 0x9000 0x0 0x0 0x2 &ipic 23 0x8
388				 0x9000 0x0 0x0 0x3 &ipic 20 0x8
389				 0x9000 0x0 0x0 0x4 &ipic 21 0x8
390
391				/* IDSEL 0x13 AD19 */
392				 0x9800 0x0 0x0 0x1 &ipic 23 0x8
393				 0x9800 0x0 0x0 0x2 &ipic 20 0x8
394				 0x9800 0x0 0x0 0x3 &ipic 21 0x8
395				 0x9800 0x0 0x0 0x4 &ipic 22 0x8
396
397				/* IDSEL 0x15 AD21*/
398				 0xa800 0x0 0x0 0x1 &ipic 20 0x8
399				 0xa800 0x0 0x0 0x2 &ipic 21 0x8
400				 0xa800 0x0 0x0 0x3 &ipic 22 0x8
401				 0xa800 0x0 0x0 0x4 &ipic 23 0x8
402
403				/* IDSEL 0x16 AD22*/
404				 0xb000 0x0 0x0 0x1 &ipic 23 0x8
405				 0xb000 0x0 0x0 0x2 &ipic 20 0x8
406				 0xb000 0x0 0x0 0x3 &ipic 21 0x8
407				 0xb000 0x0 0x0 0x4 &ipic 22 0x8
408
409				/* IDSEL 0x17 AD23*/
410				 0xb800 0x0 0x0 0x1 &ipic 22 0x8
411				 0xb800 0x0 0x0 0x2 &ipic 23 0x8
412				 0xb800 0x0 0x0 0x3 &ipic 20 0x8
413				 0xb800 0x0 0x0 0x4 &ipic 21 0x8
414
415				/* IDSEL 0x18 AD24*/
416				 0xc000 0x0 0x0 0x1 &ipic 21 0x8
417				 0xc000 0x0 0x0 0x2 &ipic 22 0x8
418				 0xc000 0x0 0x0 0x3 &ipic 23 0x8
419				 0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
420		interrupt-parent = <&ipic>;
421		interrupts = <66 0x8>;
422		bus-range = <0x0 0x0>;
423		ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
424			  0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
425			  0x01000000 0x0 0x00000000 0xd0000000 0x0 0x00100000>;
426		clock-frequency = <0>;
427		#interrupt-cells = <1>;
428		#size-cells = <2>;
429		#address-cells = <3>;
430		reg = <0xe0008500 0x100		/* internal registers */
431		       0xe0008300 0x8>;		/* config space access registers */
432		compatible = "fsl,mpc8349-pci";
433		device_type = "pci";
434		sleep = <&pmc 0x00010000>;
435	};
436};
437