1// SPDX-License-Identifier: (GPL-2.0+ OR MIT) 2/* 3 * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd 4 */ 5 6/dts-v1/; 7#include <dt-bindings/input/linux-event-codes.h> 8#include <dt-bindings/pwm/pwm.h> 9#include "rk3399.dtsi" 10#include "rk3399-opp.dtsi" 11 12/ { 13 model = "Firefly ROC-RK3399-PC Board"; 14 compatible = "firefly,roc-rk3399-pc", "rockchip,rk3399"; 15 16 aliases { 17 mmc0 = &sdmmc; 18 mmc1 = &sdhci; 19 }; 20 21 chosen { 22 stdout-path = "serial2:1500000n8"; 23 }; 24 25 backlight: backlight { 26 compatible = "pwm-backlight"; 27 pwms = <&pwm0 0 25000 0>; 28 }; 29 30 clkin_gmac: external-gmac-clock { 31 compatible = "fixed-clock"; 32 clock-frequency = <125000000>; 33 clock-output-names = "clkin_gmac"; 34 #clock-cells = <0>; 35 }; 36 37 adc-keys { 38 compatible = "adc-keys"; 39 io-channels = <&saradc 1>; 40 io-channel-names = "buttons"; 41 keyup-threshold-microvolt = <1500000>; 42 poll-interval = <100>; 43 44 recovery { 45 label = "Recovery"; 46 linux,code = <KEY_VENDOR>; 47 press-threshold-microvolt = <18000>; 48 }; 49 }; 50 51 gpio-keys { 52 compatible = "gpio-keys"; 53 autorepeat; 54 pinctrl-names = "default"; 55 pinctrl-0 = <&pwr_key_l>; 56 57 key-power { 58 debounce-interval = <100>; 59 gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>; 60 label = "GPIO Key Power"; 61 linux,code = <KEY_POWER>; 62 wakeup-source; 63 }; 64 }; 65 66 ir-receiver { 67 compatible = "gpio-ir-receiver"; 68 gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>; 69 pinctrl-names = "default"; 70 pinctrl-0 = <&ir_int>; 71 }; 72 73 leds { 74 compatible = "gpio-leds"; 75 pinctrl-names = "default"; 76 pinctrl-0 = <&work_led_pin>, <&diy_led_pin>, <&yellow_led_pin>; 77 78 work_led: led-0 { 79 label = "green:work"; 80 gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>; 81 default-state = "on"; 82 linux,default-trigger = "heartbeat"; 83 }; 84 85 diy_led: led-1 { 86 label = "red:diy"; 87 gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>; 88 default-state = "off"; 89 linux,default-trigger = "mmc2"; 90 }; 91 92 yellow_led: led-2 { 93 label = "yellow:yellow-led"; 94 gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>; 95 default-state = "off"; 96 linux,default-trigger = "mmc1"; 97 }; 98 }; 99 100 sdio_pwrseq: sdio-pwrseq { 101 compatible = "mmc-pwrseq-simple"; 102 clocks = <&rk808 1>; 103 clock-names = "ext_clock"; 104 pinctrl-names = "default"; 105 pinctrl-0 = <&wifi_enable_h>; 106 107 /* 108 * On the module itself this is one of these (depending 109 * on the actual card populated): 110 * - SDIO_RESET_L_WL_REG_ON 111 * - PDN (power down when low) 112 */ 113 reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>; 114 }; 115 116 vcc_vbus_typec0: vcc-vbus-typec0 { 117 compatible = "regulator-fixed"; 118 regulator-name = "vcc_vbus_typec0"; 119 regulator-always-on; 120 regulator-boot-on; 121 regulator-min-microvolt = <5000000>; 122 regulator-max-microvolt = <5000000>; 123 }; 124 125 sys_12v: sys-12v { 126 compatible = "regulator-fixed"; 127 regulator-name = "sys_12v"; 128 regulator-always-on; 129 regulator-boot-on; 130 vin-supply = <&dc_12v>; 131 }; 132 133 /* switched by pmic_sleep */ 134 vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 { 135 compatible = "regulator-fixed"; 136 regulator-name = "vcc1v8_s3"; 137 regulator-always-on; 138 regulator-boot-on; 139 regulator-min-microvolt = <1800000>; 140 regulator-max-microvolt = <1800000>; 141 vin-supply = <&vcc_1v8>; 142 }; 143 144 vcc3v0_sd: vcc3v0-sd { 145 compatible = "regulator-fixed"; 146 enable-active-high; 147 gpio = <&gpio4 RK_PD6 GPIO_ACTIVE_HIGH>; 148 pinctrl-names = "default"; 149 pinctrl-0 = <&vcc3v0_sd_en>; 150 regulator-name = "vcc3v0_sd"; 151 regulator-boot-on; 152 regulator-min-microvolt = <3000000>; 153 regulator-max-microvolt = <3000000>; 154 vin-supply = <&vcc3v3_sys>; 155 }; 156 157 vcc3v3_sys: vcc3v3-sys { 158 compatible = "regulator-fixed"; 159 regulator-name = "vcc3v3_sys"; 160 regulator-always-on; 161 regulator-boot-on; 162 regulator-min-microvolt = <3300000>; 163 regulator-max-microvolt = <3300000>; 164 vin-supply = <&sys_12v>; 165 }; 166 167 vcca_0v9: vcca-0v9 { 168 compatible = "regulator-fixed"; 169 regulator-name = "vcca_0v9"; 170 regulator-always-on; 171 regulator-boot-on; 172 regulator-min-microvolt = <900000>; 173 regulator-max-microvolt = <900000>; 174 vin-supply = <&vcc3v3_sys>; 175 }; 176 177 /* Actually 3 regulators (host0, 1, 2) controlled by the same gpio */ 178 vcc5v0_host: vcc5v0-host-regulator { 179 compatible = "regulator-fixed"; 180 enable-active-high; 181 gpio = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>; 182 pinctrl-names = "default"; 183 pinctrl-0 = <&vcc5v0_host_en &hub_rst>; 184 regulator-name = "vcc5v0_host"; 185 vin-supply = <&vcc_sys>; 186 }; 187 188 vcc_vbus_typec1: vcc-vbus-typec1 { 189 compatible = "regulator-fixed"; 190 enable-active-high; 191 gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>; 192 pinctrl-names = "default"; 193 pinctrl-0 = <&vcc_vbus_typec1_en>; 194 regulator-name = "vcc_vbus_typec1"; 195 regulator-always-on; 196 vin-supply = <&vcc_sys>; 197 }; 198 199 vcc_sys: vcc-sys { 200 compatible = "regulator-fixed"; 201 enable-active-high; 202 gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>; 203 pinctrl-names = "default"; 204 pinctrl-0 = <&vcc_sys_en>; 205 regulator-name = "vcc_sys"; 206 regulator-boot-on; 207 regulator-min-microvolt = <5000000>; 208 regulator-max-microvolt = <5000000>; 209 vin-supply = <&sys_12v>; 210 }; 211 212 vdd_log: vdd-log { 213 compatible = "pwm-regulator"; 214 pwms = <&pwm2 0 25000 1>; 215 regulator-name = "vdd_log"; 216 regulator-always-on; 217 regulator-boot-on; 218 regulator-min-microvolt = <450000>; 219 regulator-max-microvolt = <1400000>; 220 pwm-supply = <&vcc3v3_sys>; 221 }; 222}; 223 224&cpu_l0 { 225 cpu-supply = <&vdd_cpu_l>; 226}; 227 228&cpu_l1 { 229 cpu-supply = <&vdd_cpu_l>; 230}; 231 232&cpu_l2 { 233 cpu-supply = <&vdd_cpu_l>; 234}; 235 236&cpu_l3 { 237 cpu-supply = <&vdd_cpu_l>; 238}; 239 240&cpu_b0 { 241 cpu-supply = <&vdd_cpu_b>; 242}; 243 244&cpu_b1 { 245 cpu-supply = <&vdd_cpu_b>; 246}; 247 248&emmc_phy { 249 status = "okay"; 250}; 251 252&gmac { 253 assigned-clocks = <&cru SCLK_RMII_SRC>; 254 assigned-clock-parents = <&clkin_gmac>; 255 clock_in_out = "input"; 256 phy-supply = <&vcc_lan>; 257 phy-mode = "rgmii"; 258 pinctrl-names = "default"; 259 pinctrl-0 = <&rgmii_pins>; 260 snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>; 261 snps,reset-active-low; 262 snps,reset-delays-us = <0 10000 50000>; 263 tx_delay = <0x28>; 264 rx_delay = <0x11>; 265 status = "okay"; 266}; 267 268&gpu { 269 mali-supply = <&vdd_gpu>; 270 status = "okay"; 271}; 272 273&hdmi { 274 ddc-i2c-bus = <&i2c3>; 275 pinctrl-names = "default"; 276 pinctrl-0 = <&hdmi_cec>; 277 status = "okay"; 278}; 279 280&hdmi_sound { 281 status = "okay"; 282}; 283 284&i2c0 { 285 clock-frequency = <400000>; 286 i2c-scl-rising-time-ns = <168>; 287 i2c-scl-falling-time-ns = <4>; 288 status = "okay"; 289 290 rk808: pmic@1b { 291 compatible = "rockchip,rk808"; 292 reg = <0x1b>; 293 interrupt-parent = <&gpio1>; 294 interrupts = <21 IRQ_TYPE_LEVEL_LOW>; 295 #clock-cells = <1>; 296 clock-output-names = "xin32k", "rk808-clkout2"; 297 pinctrl-names = "default"; 298 pinctrl-0 = <&pmic_int_l>; 299 rockchip,system-power-controller; 300 wakeup-source; 301 302 vcc1-supply = <&vcc3v3_sys>; 303 vcc2-supply = <&vcc3v3_sys>; 304 vcc3-supply = <&vcc3v3_sys>; 305 vcc4-supply = <&vcc3v3_sys>; 306 vcc6-supply = <&vcc3v3_sys>; 307 vcc7-supply = <&vcc3v3_sys>; 308 vcc8-supply = <&vcc3v3_sys>; 309 vcc9-supply = <&vcc3v3_sys>; 310 vcc10-supply = <&vcc3v3_sys>; 311 vcc11-supply = <&vcc3v3_sys>; 312 vcc12-supply = <&vcc3v3_sys>; 313 vddio-supply = <&vcc_3v0>; 314 315 regulators { 316 vdd_center: DCDC_REG1 { 317 regulator-name = "vdd_center"; 318 regulator-always-on; 319 regulator-boot-on; 320 regulator-min-microvolt = <750000>; 321 regulator-max-microvolt = <1350000>; 322 regulator-ramp-delay = <6001>; 323 regulator-state-mem { 324 regulator-off-in-suspend; 325 }; 326 }; 327 328 vdd_cpu_l: DCDC_REG2 { 329 regulator-name = "vdd_cpu_l"; 330 regulator-always-on; 331 regulator-boot-on; 332 regulator-min-microvolt = <750000>; 333 regulator-max-microvolt = <1350000>; 334 regulator-ramp-delay = <6001>; 335 regulator-state-mem { 336 regulator-off-in-suspend; 337 }; 338 }; 339 340 vcc_ddr: DCDC_REG3 { 341 regulator-name = "vcc_ddr"; 342 regulator-always-on; 343 regulator-boot-on; 344 regulator-state-mem { 345 regulator-on-in-suspend; 346 }; 347 }; 348 349 vcc_1v8: DCDC_REG4 { 350 regulator-name = "vcc_1v8"; 351 regulator-always-on; 352 regulator-boot-on; 353 regulator-min-microvolt = <1800000>; 354 regulator-max-microvolt = <1800000>; 355 regulator-state-mem { 356 regulator-on-in-suspend; 357 regulator-suspend-microvolt = <1800000>; 358 }; 359 }; 360 361 vcca1v8_codec: LDO_REG1 { 362 regulator-name = "vcca1v8_codec"; 363 regulator-always-on; 364 regulator-boot-on; 365 regulator-min-microvolt = <1800000>; 366 regulator-max-microvolt = <1800000>; 367 regulator-state-mem { 368 regulator-off-in-suspend; 369 }; 370 }; 371 372 vcc1v8_hdmi: LDO_REG2 { 373 regulator-name = "vcc1v8_hdmi"; 374 regulator-always-on; 375 regulator-boot-on; 376 regulator-min-microvolt = <1800000>; 377 regulator-max-microvolt = <1800000>; 378 regulator-state-mem { 379 regulator-off-in-suspend; 380 }; 381 }; 382 383 vcc1v8_pmu: LDO_REG3 { 384 regulator-name = "vcc1v8_pmu"; 385 regulator-always-on; 386 regulator-boot-on; 387 regulator-min-microvolt = <1800000>; 388 regulator-max-microvolt = <1800000>; 389 regulator-state-mem { 390 regulator-on-in-suspend; 391 regulator-suspend-microvolt = <1800000>; 392 }; 393 }; 394 395 vcc_sdio: LDO_REG4 { 396 regulator-name = "vcc_sdio"; 397 regulator-always-on; 398 regulator-boot-on; 399 regulator-min-microvolt = <1800000>; 400 regulator-max-microvolt = <3000000>; 401 regulator-state-mem { 402 regulator-on-in-suspend; 403 regulator-suspend-microvolt = <3000000>; 404 }; 405 }; 406 407 vcca3v0_codec: LDO_REG5 { 408 regulator-name = "vcca3v0_codec"; 409 regulator-always-on; 410 regulator-boot-on; 411 regulator-min-microvolt = <3000000>; 412 regulator-max-microvolt = <3000000>; 413 regulator-state-mem { 414 regulator-off-in-suspend; 415 }; 416 }; 417 418 vcc_1v5: LDO_REG6 { 419 regulator-name = "vcc_1v5"; 420 regulator-always-on; 421 regulator-boot-on; 422 regulator-min-microvolt = <1500000>; 423 regulator-max-microvolt = <1500000>; 424 regulator-state-mem { 425 regulator-on-in-suspend; 426 regulator-suspend-microvolt = <1500000>; 427 }; 428 }; 429 430 vcca0v9_hdmi: LDO_REG7 { 431 regulator-name = "vcca0v9_hdmi"; 432 regulator-always-on; 433 regulator-boot-on; 434 regulator-min-microvolt = <900000>; 435 regulator-max-microvolt = <900000>; 436 regulator-state-mem { 437 regulator-off-in-suspend; 438 }; 439 }; 440 441 vcc_3v0: LDO_REG8 { 442 regulator-name = "vcc_3v0"; 443 regulator-always-on; 444 regulator-boot-on; 445 regulator-min-microvolt = <3000000>; 446 regulator-max-microvolt = <3000000>; 447 regulator-state-mem { 448 regulator-on-in-suspend; 449 regulator-suspend-microvolt = <3000000>; 450 }; 451 }; 452 453 vcc3v3_s3: vcc_lan: SWITCH_REG1 { 454 regulator-name = "vcc3v3_s3"; 455 regulator-always-on; 456 regulator-boot-on; 457 regulator-state-mem { 458 regulator-off-in-suspend; 459 }; 460 }; 461 462 vcc3v3_s0: SWITCH_REG2 { 463 regulator-name = "vcc3v3_s0"; 464 regulator-always-on; 465 regulator-boot-on; 466 regulator-state-mem { 467 regulator-off-in-suspend; 468 }; 469 }; 470 }; 471 }; 472 473 vdd_cpu_b: regulator@40 { 474 compatible = "silergy,syr827"; 475 reg = <0x40>; 476 fcs,suspend-voltage-selector = <1>; 477 pinctrl-names = "default"; 478 pinctrl-0 = <&vsel1_pin>; 479 regulator-name = "vdd_cpu_b"; 480 regulator-min-microvolt = <712500>; 481 regulator-max-microvolt = <1500000>; 482 regulator-ramp-delay = <1000>; 483 regulator-always-on; 484 regulator-boot-on; 485 vin-supply = <&vcc3v3_sys>; 486 487 regulator-state-mem { 488 regulator-off-in-suspend; 489 }; 490 }; 491 492 vdd_gpu: regulator@41 { 493 compatible = "silergy,syr828"; 494 reg = <0x41>; 495 fcs,suspend-voltage-selector = <1>; 496 pinctrl-names = "default"; 497 pinctrl-0 = <&vsel2_pin>; 498 regulator-name = "vdd_gpu"; 499 regulator-min-microvolt = <712500>; 500 regulator-max-microvolt = <1500000>; 501 regulator-ramp-delay = <1000>; 502 regulator-always-on; 503 regulator-boot-on; 504 vin-supply = <&vcc3v3_sys>; 505 506 regulator-state-mem { 507 regulator-off-in-suspend; 508 }; 509 }; 510}; 511 512&i2c1 { 513 i2c-scl-rising-time-ns = <300>; 514 i2c-scl-falling-time-ns = <15>; 515 status = "okay"; 516}; 517 518&i2c3 { 519 i2c-scl-rising-time-ns = <450>; 520 i2c-scl-falling-time-ns = <15>; 521 status = "okay"; 522}; 523 524&i2c4 { 525 i2c-scl-rising-time-ns = <600>; 526 i2c-scl-falling-time-ns = <20>; 527 status = "okay"; 528 529 fusb1: usb-typec@22 { 530 compatible = "fcs,fusb302"; 531 reg = <0x22>; 532 interrupt-parent = <&gpio1>; 533 interrupts = <1 IRQ_TYPE_LEVEL_LOW>; 534 pinctrl-names = "default"; 535 pinctrl-0 = <&fusb1_int>; 536 vbus-supply = <&vcc_vbus_typec1>; 537 status = "okay"; 538 }; 539}; 540 541&i2c7 { 542 i2c-scl-rising-time-ns = <600>; 543 i2c-scl-falling-time-ns = <20>; 544 status = "okay"; 545 546 fusb0: usb-typec@22 { 547 compatible = "fcs,fusb302"; 548 reg = <0x22>; 549 interrupt-parent = <&gpio1>; 550 interrupts = <2 IRQ_TYPE_LEVEL_LOW>; 551 pinctrl-names = "default"; 552 pinctrl-0 = <&fusb0_int>; 553 vbus-supply = <&vcc_vbus_typec0>; 554 status = "okay"; 555 }; 556 557 mp8859: regulator@66 { 558 compatible = "mps,mp8859"; 559 reg = <0x66>; 560 dc_12v: mp8859_dcdc { 561 regulator-name = "dc_12v"; 562 regulator-min-microvolt = <12000000>; 563 regulator-max-microvolt = <12000000>; 564 regulator-always-on; 565 regulator-boot-on; 566 vin-supply = <&vcc_vbus_typec0>; 567 568 regulator-state-mem { 569 regulator-on-in-suspend; 570 regulator-suspend-microvolt = <12000000>; 571 }; 572 }; 573 }; 574}; 575 576&i2s0 { 577 rockchip,playback-channels = <8>; 578 rockchip,capture-channels = <8>; 579 status = "okay"; 580}; 581 582&i2s1 { 583 rockchip,playback-channels = <2>; 584 rockchip,capture-channels = <2>; 585 status = "okay"; 586}; 587 588&i2s2 { 589 status = "okay"; 590}; 591 592&io_domains { 593 audio-supply = <&vcca1v8_codec>; 594 bt656-supply = <&vcc_3v0>; 595 gpio1830-supply = <&vcc_3v0>; 596 sdmmc-supply = <&vcc_sdio>; 597 status = "okay"; 598}; 599 600&pmu_io_domains { 601 pmu1830-supply = <&vcc_3v0>; 602 status = "okay"; 603}; 604 605&pinctrl { 606 buttons { 607 pwr_key_l: pwr-key-l { 608 rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>; 609 }; 610 }; 611 612 ir { 613 ir_int: ir-int { 614 rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>; 615 }; 616 }; 617 618 lcd-panel { 619 lcd_panel_reset: lcd-panel-reset { 620 rockchip,pins = <4 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>; 621 }; 622 }; 623 624 leds { 625 diy_led_pin: diy-led-pin { 626 rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>; 627 }; 628 629 work_led_pin: work-led-pin { 630 rockchip,pins = <2 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>; 631 }; 632 633 yellow_led_pin: yellow-led-pin { 634 rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>; 635 }; 636 }; 637 638 pmic { 639 vsel1_pin: vsel1-pin { 640 rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>; 641 }; 642 643 vsel2_pin: vsel2-pin { 644 rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>; 645 }; 646 }; 647 648 sdio-pwrseq { 649 wifi_enable_h: wifi-enable-h { 650 rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; 651 }; 652 }; 653 654 sdmmc { 655 vcc3v0_sd_en: vcc3v0-sd-en { 656 rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>; 657 }; 658 }; 659 660 pmic { 661 pmic_int_l: pmic-int-l { 662 rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>; 663 }; 664 }; 665 666 usb2 { 667 vcc5v0_host_en: vcc5v0-host-en { 668 rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>; 669 }; 670 671 vcc_sys_en: vcc-sys-en { 672 rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>; 673 }; 674 675 hub_rst: hub-rst { 676 rockchip,pins = <2 RK_PA4 RK_FUNC_GPIO &pcfg_output_high>; 677 }; 678 }; 679 680 usb-typec { 681 vcc_vbus_typec1_en: vcc-vbus-typec1-en { 682 rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>; 683 }; 684 }; 685 686 fusb30x { 687 fusb0_int: fusb0-int { 688 rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>; 689 }; 690 691 fusb1_int: fusb1-int { 692 rockchip,pins = <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>; 693 }; 694 }; 695}; 696 697&pwm0 { 698 status = "okay"; 699}; 700 701&pwm2 { 702 status = "okay"; 703}; 704 705&saradc { 706 vref-supply = <&vcca1v8_s3>; 707 status = "okay"; 708}; 709 710&sdmmc { 711 bus-width = <4>; 712 cap-sd-highspeed; 713 cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>; 714 disable-wp; 715 max-frequency = <150000000>; 716 pinctrl-names = "default"; 717 pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>; 718 sd-uhs-sdr104; 719 vmmc-supply = <&vcc3v0_sd>; 720 vqmmc-supply = <&vcc_sdio>; 721 status = "okay"; 722}; 723 724&sdhci { 725 bus-width = <8>; 726 non-removable; 727 status = "okay"; 728}; 729 730&spi1 { 731 status = "okay"; 732 733 flash@0 { 734 compatible = "jedec,spi-nor"; 735 reg = <0>; 736 spi-max-frequency = <10000000>; 737 }; 738}; 739 740&tcphy0 { 741 status = "okay"; 742}; 743 744&tcphy1 { 745 status = "okay"; 746}; 747 748&tsadc { 749 /* tshut mode 0:CRU 1:GPIO */ 750 rockchip,hw-tshut-mode = <1>; 751 /* tshut polarity 0:LOW 1:HIGH */ 752 rockchip,hw-tshut-polarity = <1>; 753 status = "okay"; 754}; 755 756&u2phy0 { 757 status = "okay"; 758 759 u2phy0_otg: otg-port { 760 phy-supply = <&vcc_vbus_typec0>; 761 status = "okay"; 762 }; 763 764 u2phy0_host: host-port { 765 phy-supply = <&vcc5v0_host>; 766 status = "okay"; 767 }; 768}; 769 770&u2phy1 { 771 status = "okay"; 772 773 u2phy1_otg: otg-port { 774 phy-supply = <&vcc_vbus_typec1>; 775 status = "okay"; 776 }; 777 778 u2phy1_host: host-port { 779 phy-supply = <&vcc5v0_host>; 780 status = "okay"; 781 }; 782}; 783 784&uart0 { 785 pinctrl-names = "default"; 786 pinctrl-0 = <&uart0_xfer &uart0_cts>; 787 status = "okay"; 788}; 789 790&uart2 { 791 status = "okay"; 792}; 793 794&usb_host0_ehci { 795 status = "okay"; 796}; 797 798&usb_host0_ohci { 799 status = "okay"; 800}; 801 802&usb_host1_ehci { 803 status = "okay"; 804}; 805 806&usb_host1_ohci { 807 status = "okay"; 808}; 809 810&usbdrd3_0 { 811 status = "okay"; 812}; 813 814&usbdrd_dwc3_0 { 815 status = "okay"; 816}; 817 818&usbdrd3_1 { 819 status = "okay"; 820}; 821 822&usbdrd_dwc3_1 { 823 status = "okay"; 824 dr_mode = "host"; 825}; 826 827&vopb { 828 status = "okay"; 829}; 830 831&vopb_mmu { 832 status = "okay"; 833}; 834 835&vopl { 836 status = "okay"; 837}; 838 839&vopl_mmu { 840 status = "okay"; 841}; 842