1// SPDX-License-Identifier: (GPL-2.0+ OR MIT) 2/* 3 * sc7280 Qcard device tree source 4 * 5 * Qcard PCB has the processor, RAM, eMMC (if stuffed), and eDP connector (if 6 * stuffed) on it. This device tree tries to encapsulate all the things that 7 * all boards using Qcard will have in common. Given that there are stuffing 8 * options, some things may be left with status "disabled" and enabled in 9 * the actual board device tree files. 10 * 11 * Copyright 2022 Google LLC. 12 */ 13 14#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h> 15#include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h> 16#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> 17#include <dt-bindings/regulator/qcom,rpmh-regulator.h> 18 19#include "sc7280.dtsi" 20 21/* PMICs depend on spmi_bus label and so must come after SoC */ 22#include "pm7325.dtsi" 23#include "pm8350c.dtsi" 24#include "pmk8350.dtsi" 25 26/ { 27 aliases { 28 bluetooth0 = &bluetooth; 29 serial0 = &uart5; 30 serial1 = &uart7; 31 }; 32 33 pm8350c_pwm_backlight: backlight { 34 compatible = "pwm-backlight"; 35 status = "disabled"; 36 37 enable-gpios = <&pm8350c_gpios 7 GPIO_ACTIVE_HIGH>; 38 pinctrl-names = "default"; 39 pinctrl-0 = <&pmic_edp_bl_en>; 40 pwms = <&pm8350c_pwm 3 65535>; 41 }; 42}; 43 44&apps_rsc { 45 /* 46 * Regulators are given labels corresponding to the various names 47 * they are referred to on schematics. They are also given labels 48 * corresponding to named voltage inputs on the SoC or components 49 * bundled with the SoC (like radio companion chips). We totally 50 * ignore it when one regulator is the input to another regulator. 51 * That's handled automatically by the initial config given to 52 * RPMH by the firmware. 53 * 54 * Regulators that the HLOS (High Level OS) doesn't touch at all 55 * are left out of here since they are managed elsewhere. 56 */ 57 58 pm7325-regulators { 59 compatible = "qcom,pm7325-rpmh-regulators"; 60 qcom,pmic-id = "b"; 61 62 vdd19_pmu_pcie_i: 63 vdd19_pmu_rfa_i: 64 vreg_s1b_1p856: smps1 { 65 regulator-min-microvolt = <1856000>; 66 regulator-max-microvolt = <2040000>; 67 }; 68 69 vdd_pmu_aon_i: 70 vdd09_pmu_rfa_i: 71 vdd095_mx_pmu: 72 vdd095_pmu: 73 vreg_s7b_0p952: smps7 { 74 regulator-min-microvolt = <535000>; 75 regulator-max-microvolt = <1120000>; 76 }; 77 78 vdd13_pmu_rfa_i: 79 vdd13_pmu_pcie_i: 80 vreg_s8b_1p256: smps8 { 81 regulator-min-microvolt = <1256000>; 82 regulator-max-microvolt = <1500000>; 83 }; 84 85 vdd_a_usbssdp_0_core: 86 vreg_l1b_0p912: ldo1 { 87 regulator-min-microvolt = <825000>; 88 regulator-max-microvolt = <925000>; 89 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 90 }; 91 92 vdd_a_usbhs_3p1: 93 vreg_l2b_3p072: ldo2 { 94 regulator-min-microvolt = <2700000>; 95 regulator-max-microvolt = <3544000>; 96 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 97 }; 98 99 vdd_a_csi_0_1_1p2: 100 vdd_a_csi_2_3_1p2: 101 vdd_a_csi_4_1p2: 102 vdd_a_dsi_0_1p2: 103 vdd_a_edp_0_1p2: 104 vdd_a_qlink_0_1p2: 105 vdd_a_qlink_1_1p2: 106 vdd_a_pcie_0_1p2: 107 vdd_a_pcie_1_1p2: 108 vdd_a_ufs_0_1p2: 109 vdd_a_usbssdp_0_1p2: 110 vreg_l6b_1p2: ldo6 { 111 regulator-min-microvolt = <1140000>; 112 regulator-max-microvolt = <1260000>; 113 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 114 }; 115 116 /* 117 * Despite the fact that this is named to be 2.5V on the 118 * schematic, it powers eMMC which doesn't accept 2.5V 119 */ 120 vreg_l7b_2p5: ldo7 { 121 regulator-min-microvolt = <2960000>; 122 regulator-max-microvolt = <2960000>; 123 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 124 }; 125 126 vreg_l17b_1p8: ldo17 { 127 regulator-min-microvolt = <1700000>; 128 regulator-max-microvolt = <1900000>; 129 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 130 }; 131 132 vdd_px_wcd9385: 133 vdd_txrx: 134 vddpx_0: 135 vddpx_3: 136 vddpx_7: 137 vreg_l18b_1p8: ldo18 { 138 regulator-min-microvolt = <1800000>; 139 regulator-max-microvolt = <2000000>; 140 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 141 }; 142 143 vdd_1p8: 144 vdd_px_sdr735: 145 vdd_pxm: 146 vdd18_io: 147 vddio_px_1: 148 vddio_px_2: 149 vddio_px_3: 150 vddpx_ts: 151 vddpx_wl4otp: 152 vreg_l19b_1p8: ldo19 { 153 regulator-min-microvolt = <1800000>; 154 regulator-max-microvolt = <1800000>; 155 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 156 }; 157 }; 158 159 pm8350c-regulators { 160 compatible = "qcom,pm8350c-rpmh-regulators"; 161 qcom,pmic-id = "c"; 162 163 vdd22_wlbtpa_ch0: 164 vdd22_wlbtpa_ch1: 165 vdd22_wlbtppa_ch0: 166 vdd22_wlbtppa_ch1: 167 vdd22_wlpa5g_ch0: 168 vdd22_wlpa5g_ch1: 169 vdd22_wlppa5g_ch0: 170 vdd22_wlppa5g_ch1: 171 vreg_s1c_2p2: smps1 { 172 regulator-min-microvolt = <2190000>; 173 regulator-max-microvolt = <2210000>; 174 }; 175 176 lp4_vdd2_1p052: 177 vreg_s9c_0p676: smps9 { 178 regulator-min-microvolt = <1010000>; 179 regulator-max-microvolt = <1170000>; 180 }; 181 182 vdda_apc_cs_1p8: 183 vdda_gfx_cs_1p8: 184 vdda_turing_q6_cs_1p8: 185 vdd_a_cxo_1p8: 186 vdd_a_qrefs_1p8: 187 vdd_a_usbhs_1p8: 188 vdd_qfprom: 189 vreg_l1c_1p8: ldo1 { 190 regulator-min-microvolt = <1800000>; 191 regulator-max-microvolt = <1980000>; 192 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 193 }; 194 195 vreg_l2c_1p8: ldo2 { 196 regulator-min-microvolt = <1620000>; 197 regulator-max-microvolt = <1980000>; 198 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 199 }; 200 201 vreg_l3c_3p0: ldo3 { 202 regulator-min-microvolt = <2800000>; 203 regulator-max-microvolt = <3540000>; 204 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 205 }; 206 207 vddpx_5: 208 vreg_l4c_1p8_3p0: ldo4 { 209 regulator-min-microvolt = <1620000>; 210 regulator-max-microvolt = <3300000>; 211 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 212 }; 213 214 vddpx_6: 215 vreg_l5c_1p8_3p0: ldo5 { 216 regulator-min-microvolt = <1620000>; 217 regulator-max-microvolt = <3300000>; 218 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 219 }; 220 221 vddpx_2: 222 vreg_l6c_2p96: ldo6 { 223 regulator-min-microvolt = <1800000>; 224 regulator-max-microvolt = <2950000>; 225 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 226 }; 227 228 vreg_l7c_3p0: ldo7 { 229 regulator-min-microvolt = <3000000>; 230 regulator-max-microvolt = <3544000>; 231 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 232 }; 233 234 vreg_l8c_1p8: ldo8 { 235 regulator-min-microvolt = <1620000>; 236 regulator-max-microvolt = <2000000>; 237 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 238 }; 239 240 vreg_l9c_2p96: ldo9 { 241 regulator-min-microvolt = <2960000>; 242 regulator-max-microvolt = <2960000>; 243 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 244 }; 245 246 vdd_a_csi_0_1_0p9: 247 vdd_a_csi_2_3_0p9: 248 vdd_a_csi_4_0p9: 249 vdd_a_dsi_0_0p9: 250 vdd_a_dsi_0_pll_0p9: 251 vdd_a_edp_0_0p9: 252 vdd_a_gnss_0p9: 253 vdd_a_pcie_0_core: 254 vdd_a_pcie_1_core: 255 vdd_a_qlink_0_0p9: 256 vdd_a_qlink_0_0p9_ck: 257 vdd_a_qlink_1_0p9: 258 vdd_a_qlink_1_0p9_ck: 259 vdd_a_qrefs_0p875_0: 260 vdd_a_qrefs_0p875_1: 261 vdd_a_qrefs_0p875_2: 262 vdd_a_qrefs_0p875_3: 263 vdd_a_qrefs_0p875_4_5: 264 vdd_a_qrefs_0p875_6: 265 vdd_a_qrefs_0p875_7: 266 vdd_a_qrefs_0p875_8: 267 vdd_a_qrefs_0p875_9: 268 vdd_a_ufs_0_core: 269 vdd_a_usbhs_core: 270 vreg_l10c_0p88: ldo10 { 271 regulator-min-microvolt = <720000>; 272 regulator-max-microvolt = <1050000>; 273 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 274 }; 275 276 vreg_l11c_2p8: ldo11 { 277 regulator-min-microvolt = <2800000>; 278 regulator-max-microvolt = <3544000>; 279 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 280 }; 281 282 vreg_l12c_1p8: ldo12 { 283 regulator-min-microvolt = <1650000>; 284 regulator-max-microvolt = <2000000>; 285 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 286 }; 287 288 vreg_l13c_3p0: ldo13 { 289 regulator-min-microvolt = <2700000>; 290 regulator-max-microvolt = <3544000>; 291 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; 292 }; 293 294 vdd_flash: 295 vdd_iris_rgb: 296 vdd_mic_bias: 297 vreg_bob: bob { 298 regulator-min-microvolt = <3008000>; 299 regulator-max-microvolt = <3960000>; 300 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; 301 }; 302 }; 303}; 304 305/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */ 306 307&ipa { 308 status = "okay"; 309 modem-init; 310}; 311 312/* NOTE: Not all Qcards have eDP connector stuffed */ 313&mdss_edp { 314 aux-bus { 315 edp_panel: panel { 316 compatible = "edp-panel"; 317 318 backlight = <&pm8350c_pwm_backlight>; 319 320 ports { 321 #address-cells = <1>; 322 #size-cells = <0>; 323 port@0 { 324 reg = <0>; 325 edp_panel_in: endpoint { 326 remote-endpoint = <&mdss_edp_out>; 327 }; 328 }; 329 }; 330 }; 331 }; 332}; 333 334&mdss_edp_out { 335 remote-endpoint = <&edp_panel_in>; 336}; 337 338&mdss_edp_phy { 339 vdda-pll-supply = <&vdd_a_edp_0_0p9>; 340 vdda-phy-supply = <&vdd_a_edp_0_1p2>; 341}; 342 343&pcie1_phy { 344 vdda-phy-supply = <&vreg_l10c_0p88>; 345 vdda-pll-supply = <&vreg_l6b_1p2>; 346}; 347 348&pm8350c_pwm { 349 pinctrl-names = "default"; 350 pinctrl-0 = <&pmic_edp_bl_pwm>; 351}; 352 353&pmk8350_vadc { 354 pmk8350-die-temp@3 { 355 reg = <PMK8350_ADC7_DIE_TEMP>; 356 label = "pmk8350_die_temp"; 357 qcom,pre-scaling = <1 1>; 358 }; 359 360 pmr735a-die-temp@403 { 361 reg = <PMR735A_ADC7_DIE_TEMP>; 362 label = "pmr735a_die_temp"; 363 qcom,pre-scaling = <1 1>; 364 }; 365}; 366 367&qfprom { 368 vcc-supply = <&vdd_qfprom>; 369}; 370 371/* For eMMC. NOTE: not all Qcards have eMMC stuffed */ 372&sdhc_1 { 373 vmmc-supply = <&vreg_l7b_2p5>; 374 vqmmc-supply = <&vreg_l19b_1p8>; 375 376 non-removable; 377 no-sd; 378 no-sdio; 379}; 380 381uart_dbg: &uart5 { 382 compatible = "qcom,geni-debug-uart"; 383 status = "okay"; 384}; 385 386mos_bt_uart: &uart7 { 387 status = "okay"; 388 389 /delete-property/ interrupts; 390 interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>, 391 <&tlmm 31 IRQ_TYPE_EDGE_FALLING>; 392 pinctrl-names = "default", "sleep"; 393 pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>; 394 395 bluetooth: bluetooth { 396 compatible = "qcom,wcn6750-bt"; 397 pinctrl-names = "default"; 398 pinctrl-0 = <&mos_bt_en>; 399 enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; 400 swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>; 401 vddaon-supply = <&vreg_s7b_0p952>; 402 vddbtcxmx-supply = <&vreg_s7b_0p952>; 403 vddrfacmn-supply = <&vreg_s7b_0p952>; 404 vddrfa0p8-supply = <&vreg_s7b_0p952>; 405 vddrfa1p7-supply = <&vdd19_pmu_rfa_i>; 406 vddrfa1p2-supply = <&vdd13_pmu_rfa_i>; 407 vddrfa2p2-supply = <&vreg_s1c_2p2>; 408 vddasd-supply = <&vreg_l11c_2p8>; 409 vddio-supply = <&vreg_l18b_1p8>; 410 max-speed = <3200000>; 411 }; 412}; 413 414&usb_1_hsphy { 415 vdda-pll-supply = <&vdd_a_usbhs_core>; 416 vdda33-supply = <&vdd_a_usbhs_3p1>; 417 vdda18-supply = <&vdd_a_usbhs_1p8>; 418}; 419 420&usb_1_qmpphy { 421 vdda-phy-supply = <&vdd_a_usbssdp_0_1p2>; 422 vdda-pll-supply = <&vdd_a_usbssdp_0_core>; 423}; 424 425&usb_2_hsphy { 426 vdda-pll-supply = <&vdd_a_usbhs_core>; 427 vdda33-supply = <&vdd_a_usbhs_3p1>; 428 vdda18-supply = <&vdd_a_usbhs_1p8>; 429}; 430 431/* 432 * PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES 433 * 434 * NOTE: In general if pins leave the Qcard then the pinctrl goes in the 435 * baseboard or board device tree, not here. 436 */ 437 438/* No external pull for eDP HPD, so set the internal one. */ 439&edp_hot_plug_det { 440 bias-pull-down; 441}; 442 443/* 444 * For ts_i2c 445 * 446 * Technically this i2c bus actually leaves the Qcard, but it leaves directly 447 * via the eDP connector (it doesn't hit the baseboard). The external pulls 448 * are on Qcard. 449 */ 450&qup_i2c13_data_clk { 451 /* Has external pull */ 452 bias-disable; 453 drive-strength = <2>; 454}; 455 456/* For mos_bt_uart */ 457&qup_uart7_cts { 458 /* 459 * Configure a bias-bus-hold on CTS to lower power 460 * usage when Bluetooth is turned off. Bus hold will 461 * maintain a low power state regardless of whether 462 * the Bluetooth module drives the pin in either 463 * direction or leaves the pin fully unpowered. 464 */ 465 bias-bus-hold; 466}; 467 468/* For mos_bt_uart */ 469&qup_uart7_rts { 470 /* We'll drive RTS, so no pull */ 471 bias-disable; 472 drive-strength = <2>; 473}; 474 475/* For mos_bt_uart */ 476&qup_uart7_tx { 477 /* We'll drive TX, so no pull */ 478 bias-disable; 479 drive-strength = <2>; 480}; 481 482/* For mos_bt_uart */ 483&qup_uart7_rx { 484 /* 485 * Configure a pull-up on RX. This is needed to avoid 486 * garbage data when the TX pin of the Bluetooth module is 487 * in tri-state (module powered off or not driving the 488 * signal yet). 489 */ 490 bias-pull-up; 491}; 492 493/* eMMC, if stuffed, is straight on the Qcard */ 494&sdc1_clk { 495 bias-disable; 496 drive-strength = <16>; 497}; 498 499&sdc1_cmd { 500 bias-pull-up; 501 drive-strength = <10>; 502}; 503 504&sdc1_data { 505 bias-pull-up; 506 drive-strength = <10>; 507}; 508 509&sdc1_rclk { 510 bias-pull-down; 511}; 512 513/* 514 * PINCTRL - QCARD 515 * 516 * This has entries that are defined by Qcard even if they go to the main 517 * board. In cases where the pulls may be board dependent we defer those 518 * settings to the board device tree. Drive strengths tend to be assinged here 519 * but could conceivably be overwridden by board device trees. 520 */ 521 522&pm8350c_gpios { 523 pmic_edp_bl_en: pmic-edp-bl-en-state { 524 pins = "gpio7"; 525 function = "normal"; 526 bias-disable; 527 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; 528 529 /* Force backlight to be disabled to match state at boot. */ 530 output-low; 531 }; 532 533 pmic_edp_bl_pwm: pmic-edp-bl-pwm-state { 534 pins = "gpio8"; 535 function = "func1"; 536 bias-disable; 537 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; 538 output-low; 539 power-source = <0>; 540 }; 541}; 542 543&tlmm { 544 mos_bt_en: mos-bt-en { 545 pins = "gpio85"; 546 function = "gpio"; 547 drive-strength = <2>; 548 output-low; 549 }; 550 551 /* For mos_bt_uart */ 552 qup_uart7_sleep_cts: qup-uart7-sleep-cts { 553 pins = "gpio28"; 554 function = "gpio"; 555 /* 556 * Configure a bias-bus-hold on CTS to lower power 557 * usage when Bluetooth is turned off. Bus hold will 558 * maintain a low power state regardless of whether 559 * the Bluetooth module drives the pin in either 560 * direction or leaves the pin fully unpowered. 561 */ 562 bias-bus-hold; 563 }; 564 565 /* For mos_bt_uart */ 566 qup_uart7_sleep_rts: qup-uart7-sleep-rts { 567 pins = "gpio29"; 568 function = "gpio"; 569 /* 570 * Configure pull-down on RTS. As RTS is active low 571 * signal, pull it low to indicate the BT SoC that it 572 * can wakeup the system anytime from suspend state by 573 * pulling RX low (by sending wakeup bytes). 574 */ 575 bias-pull-down; 576 }; 577 578 /* For mos_bt_uart */ 579 qup_uart7_sleep_rx: qup-uart7-sleep-rx { 580 pins = "gpio31"; 581 function = "gpio"; 582 /* 583 * Configure a pull-up on RX. This is needed to avoid 584 * garbage data when the TX pin of the Bluetooth module 585 * is floating which may cause spurious wakeups. 586 */ 587 bias-pull-up; 588 }; 589 590 /* For mos_bt_uart */ 591 qup_uart7_sleep_tx: qup-uart7-sleep-tx { 592 pins = "gpio30"; 593 function = "gpio"; 594 /* 595 * Configure pull-up on TX when it isn't actively driven 596 * to prevent BT SoC from receiving garbage during sleep. 597 */ 598 bias-pull-up; 599 }; 600 601 ts_int_conn: ts-int-conn { 602 pins = "gpio55"; 603 function = "gpio"; 604 bias-pull-up; 605 }; 606 607 ts_rst_conn: ts-rst-conn { 608 pins = "gpio54"; 609 function = "gpio"; 610 drive-strength = <2>; 611 }; 612}; 613