1// SPDX-License-Identifier: (GPL-2.0+ OR MIT) 2/* 3 * Google Herobrine baseboard device tree source 4 * 5 * The set of things in this file is a bit loosely defined. It's roughly 6 * defined as the set of things that the child boards happen to have in 7 * common. Since all of the child boards started from the same original 8 * design this is hopefully a large set of things but as more derivatives 9 * appear things may "bubble down" out of this file. For things that are 10 * part of the reference design but might not exist on child nodes we will 11 * follow the lead of the SoC dtsi files and leave their status as "disabled". 12 * 13 * Copyright 2022 Google LLC. 14 */ 15 16#include <dt-bindings/input/gpio-keys.h> 17#include <dt-bindings/input/input.h> 18#include <dt-bindings/leds/common.h> 19 20#include "sc7280-qcard.dtsi" 21#include "sc7280-chrome-common.dtsi" 22 23/ { 24 chosen { 25 stdout-path = "serial0:115200n8"; 26 }; 27 28 /* 29 * FIXED REGULATORS 30 * 31 * Sort order: 32 * 1. parents above children. 33 * 2. higher voltage above lower voltage. 34 * 3. alphabetically by node name. 35 */ 36 37 /* This is the top level supply and variable voltage */ 38 ppvar_sys: ppvar-sys-regulator { 39 compatible = "regulator-fixed"; 40 regulator-name = "ppvar_sys"; 41 regulator-always-on; 42 regulator-boot-on; 43 }; 44 45 /* This divides ppvar_sys by 2, so voltage is variable */ 46 src_vph_pwr: src-vph-pwr-regulator { 47 compatible = "regulator-fixed"; 48 regulator-name = "src_vph_pwr"; 49 50 /* EC turns on with switchcap_on; always on for AP */ 51 regulator-always-on; 52 regulator-boot-on; 53 54 vin-supply = <&ppvar_sys>; 55 }; 56 57 pp5000_s5: pp5000-s5-regulator { 58 compatible = "regulator-fixed"; 59 regulator-name = "pp5000_s5"; 60 61 /* EC turns on with en_pp5000_s5; always on for AP */ 62 regulator-always-on; 63 regulator-boot-on; 64 regulator-min-microvolt = <5000000>; 65 regulator-max-microvolt = <5000000>; 66 67 vin-supply = <&ppvar_sys>; 68 }; 69 70 pp3300_z1: pp3300-z1-regulator { 71 compatible = "regulator-fixed"; 72 regulator-name = "pp3300_z1"; 73 74 /* EC turns on with en_pp3300_z1; always on for AP */ 75 regulator-always-on; 76 regulator-boot-on; 77 regulator-min-microvolt = <3300000>; 78 regulator-max-microvolt = <3300000>; 79 80 vin-supply = <&ppvar_sys>; 81 }; 82 83 pp3300_codec: pp3300-codec-regulator { 84 compatible = "regulator-fixed"; 85 regulator-name = "pp3300_codec"; 86 87 regulator-min-microvolt = <3300000>; 88 regulator-max-microvolt = <3300000>; 89 90 gpio = <&tlmm 105 GPIO_ACTIVE_HIGH>; 91 enable-active-high; 92 pinctrl-names = "default"; 93 pinctrl-0 = <&en_pp3300_codec>; 94 95 vin-supply = <&pp3300_z1>; 96 status = "disabled"; 97 }; 98 99 pp3300_left_in_mlb: pp3300-left-in-mlb-regulator { 100 compatible = "regulator-fixed"; 101 regulator-name = "pp3300_left_in_mlb"; 102 103 regulator-min-microvolt = <3300000>; 104 regulator-max-microvolt = <3300000>; 105 106 gpio = <&tlmm 80 GPIO_ACTIVE_HIGH>; 107 enable-active-high; 108 pinctrl-names = "default"; 109 pinctrl-0 = <&en_pp3300_dx_edp>; 110 111 regulator-enable-ramp-delay = <3000>; 112 113 /* 114 * eDP panel specs nearly always have a spec that says you 115 * shouldn't turn them off an on again without waiting 500ms. 116 * Add this as a board constraint since this rail is shared 117 * between the panel and touchscreen. 118 */ 119 off-on-delay-us = <500000>; 120 121 /* 122 * Stat the regulator on. This has the advantage of starting 123 * the slow process of powering the panel on as soon as we 124 * probe the regulator. It also avoids tripping the 125 * off-on-delay immediately on every bootup. 126 */ 127 regulator-boot-on; 128 129 vin-supply = <&pp3300_z1>; 130 }; 131 132 pp3300_mcu_fp: 133 pp3300_fp_ls: 134 pp3300_fp_mcu: pp3300-fp-regulator { 135 compatible = "regulator-fixed"; 136 regulator-name = "pp3300_fp"; 137 138 regulator-min-microvolt = <3300000>; 139 regulator-max-microvolt = <3300000>; 140 141 regulator-boot-on; 142 regulator-always-on; 143 144 /* 145 * WARNING: it is intentional that GPIO 77 isn't listed here. 146 * The userspace script for updating the fingerprint firmware 147 * needs to control the FP regulators during a FW update, 148 * hence the signal can't be owned by the kernel regulator. 149 */ 150 151 pinctrl-names = "default"; 152 pinctrl-0 = <&en_fp_rails>; 153 154 vin-supply = <&pp3300_z1>; 155 status = "disabled"; 156 }; 157 158 pp3300_hub: pp3300-hub-regulator { 159 compatible = "regulator-fixed"; 160 regulator-name = "pp3300_hub"; 161 162 regulator-min-microvolt = <3300000>; 163 regulator-max-microvolt = <3300000>; 164 165 /* The BIOS leaves this regulator on */ 166 regulator-boot-on; 167 168 gpio = <&tlmm 157 GPIO_ACTIVE_HIGH>; 169 enable-active-high; 170 pinctrl-names = "default"; 171 pinctrl-0 = <&hub_en>; 172 173 vin-supply = <&pp3300_z1>; 174 }; 175 176 pp3300_tp: pp3300-tp-regulator { 177 compatible = "regulator-fixed"; 178 regulator-name = "pp3300_tp"; 179 180 regulator-min-microvolt = <3300000>; 181 regulator-max-microvolt = <3300000>; 182 183 /* AP turns on with PP1800_L18B_S0; always on for AP */ 184 regulator-always-on; 185 regulator-boot-on; 186 187 vin-supply = <&pp3300_z1>; 188 }; 189 190 pp3300_ssd: pp3300-ssd-regulator { 191 compatible = "regulator-fixed"; 192 regulator-name = "pp3300_ssd"; 193 194 regulator-min-microvolt = <3300000>; 195 regulator-max-microvolt = <3300000>; 196 197 gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>; 198 enable-active-high; 199 pinctrl-names = "default"; 200 pinctrl-0 = <&ssd_en>; 201 202 /* 203 * The bootloaer may have left PCIe configured. Powering this 204 * off while the PCIe clocks are still running isn't great, 205 * so it's better to default to this regulator being on. 206 */ 207 regulator-boot-on; 208 209 vin-supply = <&pp3300_z1>; 210 }; 211 212 pp2850_vcm_wf_cam: pp2850-vcm-wf-cam-regulator { 213 compatible = "regulator-fixed"; 214 regulator-name = "pp2850_vcm_wf_cam"; 215 216 regulator-min-microvolt = <2850000>; 217 regulator-max-microvolt = <2850000>; 218 219 gpio = <&tlmm 119 GPIO_ACTIVE_HIGH>; 220 enable-active-high; 221 pinctrl-names = "default"; 222 pinctrl-0 = <&wf_cam_en>; 223 224 vin-supply = <&pp3300_z1>; 225 status = "disabled"; 226 }; 227 228 pp2850_wf_cam: pp2850-wf-cam-regulator { 229 compatible = "regulator-fixed"; 230 regulator-name = "pp2850_wf_cam"; 231 232 regulator-min-microvolt = <2850000>; 233 regulator-max-microvolt = <2850000>; 234 235 gpio = <&tlmm 119 GPIO_ACTIVE_HIGH>; 236 enable-active-high; 237 /* 238 * The pinconf can only be referenced once so we put it on the 239 * first regulator and comment it out here. 240 * 241 * pinctrl-names = "default"; 242 * pinctrl-0 = <&wf_cam_en>; 243 */ 244 245 vin-supply = <&pp3300_z1>; 246 status = "disabled"; 247 }; 248 249 pp1800_fp: pp1800-fp-regulator { 250 compatible = "regulator-fixed"; 251 regulator-name = "pp1800_fp"; 252 253 regulator-min-microvolt = <1800000>; 254 regulator-max-microvolt = <1800000>; 255 256 regulator-boot-on; 257 regulator-always-on; 258 259 /* 260 * WARNING: it is intentional that GPIO 77 isn't listed here. 261 * The userspace script for updating the fingerprint firmware 262 * needs to control the FP regulators during a FW update, 263 * hence the signal can't be owned by the kernel regulator. 264 */ 265 266 pinctrl-names = "default"; 267 pinctrl-0 = <&en_fp_rails>; 268 269 vin-supply = <&pp1800_l18b_s0>; 270 status = "disabled"; 271 }; 272 273 pp1800_wf_cam: pp1800-wf-cam-regulator { 274 compatible = "regulator-fixed"; 275 regulator-name = "pp1800_wf_cam"; 276 277 regulator-min-microvolt = <1800000>; 278 regulator-max-microvolt = <1800000>; 279 280 gpio = <&tlmm 119 GPIO_ACTIVE_HIGH>; 281 enable-active-high; 282 /* 283 * The pinconf can only be referenced once so we put it on the 284 * first regulator and comment it out here. 285 * 286 * pinctrl-names = "default"; 287 * pinctrl-0 = <&wf_cam_en>; 288 */ 289 290 vin-supply = <&vreg_l19b_s0>; 291 status = "disabled"; 292 }; 293 294 pp1200_wf_cam: pp1200-wf-cam-regulator { 295 compatible = "regulator-fixed"; 296 regulator-name = "pp1200_wf_cam"; 297 298 regulator-min-microvolt = <1200000>; 299 regulator-max-microvolt = <1200000>; 300 301 gpio = <&tlmm 119 GPIO_ACTIVE_HIGH>; 302 enable-active-high; 303 /* 304 * The pinconf can only be referenced once so we put it on the 305 * first regulator and comment it out here. 306 * 307 * pinctrl-names = "default"; 308 * pinctrl-0 = <&wf_cam_en>; 309 */ 310 311 vin-supply = <&pp3300_z1>; 312 status = "disabled"; 313 }; 314 315 /* BOARD-SPECIFIC TOP LEVEL NODES */ 316 317 max98360a: audio-codec-0 { 318 compatible = "maxim,max98360a"; 319 pinctrl-names = "default"; 320 pinctrl-0 = <&_en>; 321 sdmode-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>; 322 #sound-dai-cells = <0>; 323 }; 324 325 pwmleds: pwmleds { 326 compatible = "pwm-leds"; 327 status = "disabled"; 328 keyboard_backlight: led-0 { 329 label = "cros_ec::kbd_backlight"; 330 function = LED_FUNCTION_KBD_BACKLIGHT; 331 pwms = <&cros_ec_pwm 0>; 332 max-brightness = <1023>; 333 }; 334 }; 335}; 336 337/* 338 * ADJUSTMENTS TO QCARD REGULATORS 339 * 340 * Mostly this is just board-local names for regulators that come from 341 * Qcard, but this also has some minor regulator overrides. 342 * 343 * Names are only listed here if regulators go somewhere other than a 344 * testpoint. 345 */ 346 347/* From Qcard to our board; ordered by PMIC-ID / rail number */ 348 349pp1256_s8b: &vreg_s8b_1p256 {}; 350 351pp1800_l18b_s0: &vreg_l18b_1p8 {}; 352pp1800_l18b: &vreg_l18b_1p8 {}; 353 354vreg_l19b_s0: &vreg_l19b_1p8 {}; 355 356pp1800_alc5682: &vreg_l2c_1p8 {}; 357pp1800_l2c: &vreg_l2c_1p8 {}; 358 359vreg_l4c: &vreg_l4c_1p8_3p0 {}; 360 361ppvar_l6c: &vreg_l6c_2p96 {}; 362 363pp3000_l7c: &vreg_l7c_3p0 {}; 364 365pp1800_prox: &vreg_l8c_1p8 {}; 366pp1800_l8c: &vreg_l8c_1p8 {}; 367 368pp2950_l9c: &vreg_l9c_2p96 {}; 369 370pp1800_lcm: &vreg_l12c_1p8 {}; 371pp1800_mipi: &vreg_l12c_1p8 {}; 372pp1800_l12c: &vreg_l12c_1p8 {}; 373 374pp3300_lcm: &vreg_l13c_3p0 {}; 375pp3300_mipi: &vreg_l13c_3p0 {}; 376pp3300_l13c: &vreg_l13c_3p0 {}; 377 378/* From our board to Qcard; ordered same as node definition above */ 379 380vreg_edp_bl: &ppvar_sys {}; 381 382ts_avdd: &pp3300_left_in_mlb {}; 383vreg_edp_3p3: &pp3300_left_in_mlb {}; 384 385/* Regulator overrides from Qcard */ 386 387/* 388 * Herobrine boards only use l2c to power an external audio codec (like 389 * alc5682) and we want that to be at 1.8V, not at some slightly lower voltage. 390 */ 391&vreg_l2c_1p8 { 392 regulator-min-microvolt = <1800000>; 393}; 394 395/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */ 396 397&edp_panel { 398 /* Our board provides power to the qcard for the eDP panel. */ 399 power-supply = <&vreg_edp_3p3>; 400}; 401 402ap_sar_sensor_i2c: &i2c1 { 403 clock-frequency = <400000>; 404 status = "disabled"; 405 406 ap_sar_sensor0: proximity@28 { 407 compatible = "semtech,sx9324"; 408 reg = <0x28>; 409 #io-channel-cells = <1>; 410 pinctrl-names = "default"; 411 pinctrl-0 = <&sar0_irq_odl>; 412 413 interrupt-parent = <&tlmm>; 414 interrupts = <141 IRQ_TYPE_LEVEL_LOW>; 415 416 vdd-supply = <&pp1800_prox>; 417 418 label = "proximity-wifi_cellular-0"; 419 status = "disabled"; 420 }; 421 422 ap_sar_sensor1: proximity@2c { 423 compatible = "semtech,sx9324"; 424 reg = <0x2c>; 425 #io-channel-cells = <1>; 426 pinctrl-names = "default"; 427 pinctrl-0 = <&sar1_irq_odl>; 428 429 interrupt-parent = <&tlmm>; 430 interrupts = <140 IRQ_TYPE_LEVEL_LOW>; 431 432 vdd-supply = <&pp1800_prox>; 433 434 label = "proximity-wifi_cellular-1"; 435 status = "disabled"; 436 }; 437}; 438 439ap_i2c_tpm: &i2c14 { 440 status = "okay"; 441 clock-frequency = <400000>; 442 443 tpm@50 { 444 compatible = "google,cr50"; 445 reg = <0x50>; 446 447 pinctrl-names = "default"; 448 pinctrl-0 = <&gsc_ap_int_odl>; 449 450 interrupt-parent = <&tlmm>; 451 interrupts = <104 IRQ_TYPE_EDGE_RISING>; 452 }; 453}; 454 455&mdss { 456 status = "okay"; 457}; 458 459&mdss_dp { 460 status = "okay"; 461 pinctrl-names = "default"; 462 pinctrl-0 = <&dp_hot_plug_det>; 463}; 464 465&mdss_dp_out { 466 data-lanes = <0 1>; 467 link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>; 468}; 469 470/* NVMe drive, enabled on a per-board basis */ 471&pcie1 { 472 pinctrl-names = "default"; 473 pinctrl-0 = <&pcie1_clkreq_n>, <&ssd_rst_l>, <&pe_wake_odl>; 474 475 perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>; 476 vddpe-3v3-supply = <&pp3300_ssd>; 477}; 478 479&pm8350c_pwm { 480 status = "okay"; 481}; 482 483&pm8350c_pwm_backlight { 484 status = "okay"; 485 486 /* Our board provides power to the qcard for the backlight */ 487 power-supply = <&vreg_edp_bl>; 488}; 489 490&pmk8350_rtc { 491 status = "disabled"; 492}; 493 494&qupv3_id_0 { 495 status = "okay"; 496}; 497 498&qupv3_id_1 { 499 status = "okay"; 500}; 501 502/* SD Card, enabled on a per-board basis */ 503&sdhc_2 { 504 pinctrl-0 = <&sdc2_clk>, <&sdc2_cmd>, <&sdc2_data>, <&sd_cd_odl>; 505 pinctrl-1 = <&sdc2_clk_sleep>, <&sdc2_cmd_sleep>, <&sdc2_data_sleep>, <&sd_cd_odl>; 506 507 vmmc-supply = <&pp2950_l9c>; 508 vqmmc-supply = <&ppvar_l6c>; 509 510 cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>; 511}; 512 513&spi_flash { 514 spi-max-frequency = <50000000>; 515}; 516 517/* Fingerprint, enabled on a per-board basis */ 518ap_spi_fp: &spi9 { 519 pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs_gpio_init_high>, <&qup_spi9_cs_gpio>; 520 521 cs-gpios = <&tlmm 39 GPIO_ACTIVE_LOW>; 522 523 cros_ec_fp: ec@0 { 524 compatible = "google,cros-ec-fp", "google,cros-ec-spi"; 525 reg = <0>; 526 interrupt-parent = <&tlmm>; 527 interrupts = <61 IRQ_TYPE_LEVEL_LOW>; 528 pinctrl-names = "default"; 529 pinctrl-0 = <&fp_to_ap_irq_l>, <&fp_rst_l>, <&fpmcu_boot0>; 530 boot0-gpios = <&tlmm 68 GPIO_ACTIVE_HIGH>; 531 reset-gpios = <&tlmm 78 GPIO_ACTIVE_LOW>; 532 spi-max-frequency = <3000000>; 533 vdd-supply = <&pp3300_fp_mcu>; 534 }; 535}; 536 537ap_ec_spi: &spi10 { 538 status = "okay"; 539 pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs_gpio_init_high>, <&qup_spi10_cs_gpio>; 540 541 cs-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>; 542 543 cros_ec: ec@0 { 544 compatible = "google,cros-ec-spi"; 545 reg = <0>; 546 interrupt-parent = <&tlmm>; 547 interrupts = <18 IRQ_TYPE_LEVEL_LOW>; 548 pinctrl-names = "default"; 549 pinctrl-0 = <&ap_ec_int_l>; 550 spi-max-frequency = <3000000>; 551 552 cros_ec_pwm: pwm { 553 compatible = "google,cros-ec-pwm"; 554 #pwm-cells = <1>; 555 }; 556 557 i2c_tunnel: i2c-tunnel { 558 compatible = "google,cros-ec-i2c-tunnel"; 559 google,remote-bus = <0>; 560 #address-cells = <1>; 561 #size-cells = <0>; 562 }; 563 564 typec { 565 compatible = "google,cros-ec-typec"; 566 #address-cells = <1>; 567 #size-cells = <0>; 568 569 usb_c0: connector@0 { 570 compatible = "usb-c-connector"; 571 reg = <0>; 572 label = "left"; 573 power-role = "dual"; 574 data-role = "host"; 575 try-power-role = "source"; 576 }; 577 578 usb_c1: connector@1 { 579 compatible = "usb-c-connector"; 580 reg = <1>; 581 label = "right"; 582 power-role = "dual"; 583 data-role = "host"; 584 try-power-role = "source"; 585 }; 586 }; 587 }; 588}; 589 590#include <arm/cros-ec-keyboard.dtsi> 591#include <arm/cros-ec-sbs.dtsi> 592 593&keyboard_controller { 594 function-row-physmap = < 595 MATRIX_KEY(0x00, 0x02, 0) /* T1 */ 596 MATRIX_KEY(0x03, 0x02, 0) /* T2 */ 597 MATRIX_KEY(0x02, 0x02, 0) /* T3 */ 598 MATRIX_KEY(0x01, 0x02, 0) /* T4 */ 599 MATRIX_KEY(0x03, 0x04, 0) /* T5 */ 600 MATRIX_KEY(0x02, 0x04, 0) /* T6 */ 601 MATRIX_KEY(0x01, 0x04, 0) /* T7 */ 602 MATRIX_KEY(0x02, 0x09, 0) /* T8 */ 603 MATRIX_KEY(0x01, 0x09, 0) /* T9 */ 604 MATRIX_KEY(0x00, 0x04, 0) /* T10 */ 605 >; 606 linux,keymap = < 607 MATRIX_KEY(0x00, 0x02, KEY_BACK) 608 MATRIX_KEY(0x03, 0x02, KEY_REFRESH) 609 MATRIX_KEY(0x02, 0x02, KEY_ZOOM) 610 MATRIX_KEY(0x01, 0x02, KEY_SCALE) 611 MATRIX_KEY(0x03, 0x04, KEY_SYSRQ) 612 MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN) 613 MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP) 614 MATRIX_KEY(0x02, 0x09, KEY_MUTE) 615 MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN) 616 MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP) 617 618 CROS_STD_MAIN_KEYMAP 619 >; 620}; 621 622&usb_1 { 623 status = "okay"; 624}; 625 626&usb_1_dwc3 { 627 dr_mode = "host"; 628 629 #address-cells = <1>; 630 #size-cells = <0>; 631 632 /* 2.x hub on port 1 */ 633 usb_hub_2_x: hub@1 { 634 compatible = "usbbda,5411"; 635 reg = <1>; 636 vdd-supply = <&pp3300_hub>; 637 peer-hub = <&usb_hub_3_x>; 638 }; 639 640 /* 3.x hub on port 2 */ 641 usb_hub_3_x: hub@2 { 642 compatible = "usbbda,411"; 643 reg = <2>; 644 vdd-supply = <&pp3300_hub>; 645 peer-hub = <&usb_hub_2_x>; 646 }; 647}; 648 649&usb_1_hsphy { 650 status = "okay"; 651 652 qcom,hs-rise-fall-time-bp = <0>; 653 qcom,squelch-detector-bp = <(-2090)>; 654 qcom,hs-disconnect-bp = <1743>; 655 qcom,hs-amplitude-bp = <1780>; 656 qcom,hs-crossover-voltage-microvolt = <(-31000)>; 657 qcom,hs-output-impedance-micro-ohms = <2600000>; 658}; 659 660&usb_1_qmpphy { 661 status = "okay"; 662}; 663 664/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */ 665 666&dp_hot_plug_det { 667 bias-disable; 668}; 669 670&mi2s1_data0 { 671 drive-strength = <6>; 672 bias-disable; 673}; 674 675&mi2s1_sclk { 676 drive-strength = <6>; 677 bias-disable; 678}; 679 680&mi2s1_ws { 681 drive-strength = <6>; 682 bias-disable; 683}; 684 685&pcie1_clkreq_n { 686 bias-pull-up; 687 drive-strength = <2>; 688}; 689 690&qspi_cs0 { 691 bias-disable; /* External pullup */ 692 drive-strength = <8>; 693}; 694 695&qspi_clk { 696 bias-pull-down; /* No external pulls */ 697 drive-strength = <8>; 698}; 699 700&qspi_data0 { 701 bias-pull-down; /* No external pulls */ 702 drive-strength = <8>; 703}; 704 705&qspi_data1 { 706 bias-disable; /* External pulldown */ 707 drive-strength = <8>; 708}; 709 710/* For ap_tp_i2c */ 711&qup_i2c0_data_clk { 712 /* Has external pull */ 713 bias-disable; 714 drive-strength = <2>; 715}; 716 717/* For ap_i2c_tpm */ 718&qup_i2c14_data_clk { 719 /* Has external pull */ 720 bias-disable; 721 drive-strength = <2>; 722}; 723 724/* For ap_spi_fp */ 725&qup_spi9_data_clk { 726 bias-disable; 727 drive-strength = <2>; 728}; 729 730/* For ap_spi_fp */ 731&qup_spi9_cs_gpio { 732 bias-disable; 733 drive-strength = <2>; 734}; 735 736/* For ap_ec_spi */ 737&qup_spi10_data_clk { 738 bias-disable; 739 drive-strength = <2>; 740}; 741 742/* For ap_ec_spi */ 743&qup_spi10_cs_gpio { 744 bias-disable; 745 drive-strength = <2>; 746}; 747 748/* For uart_dbg */ 749&qup_uart5_rx { 750 bias-pull-up; 751}; 752 753/* For uart_dbg */ 754&qup_uart5_tx { 755 bias-disable; 756 drive-strength = <2>; 757}; 758 759&sdc2_clk { 760 bias-disable; 761 drive-strength = <16>; 762}; 763 764&sdc2_cmd { 765 bias-pull-up; 766 drive-strength = <10>; 767}; 768 769&sdc2_data { 770 bias-pull-up; 771 drive-strength = <10>; 772}; 773 774/* PINCTRL - board-specific pinctrl */ 775 776&pm7325_gpios { 777 /* 778 * On a quick glance it might look like KYPD_VOL_UP_N is used, but 779 * that only passes through to a debug connector and not to the actual 780 * volume up key. 781 */ 782 status = "disabled"; /* No GPIOs are connected */ 783}; 784 785&pmk8350_gpios { 786 status = "disabled"; /* No GPIOs are connected */ 787}; 788 789&tlmm { 790 /* pinctrl settings for pins that have no real owners. */ 791 pinctrl-names = "default"; 792 pinctrl-0 = <&bios_flash_wp_od>; 793 794 amp_en: amp-en-state { 795 pins = "gpio63"; 796 function = "gpio"; 797 bias-disable; 798 drive-strength = <2>; 799 }; 800 801 ap_ec_int_l: ap-ec-int-l-state { 802 pins = "gpio18"; 803 function = "gpio"; 804 bias-pull-up; 805 }; 806 807 bios_flash_wp_od: bios-flash-wp-od-state { 808 pins = "gpio16"; 809 function = "gpio"; 810 /* Has external pull */ 811 bias-disable; 812 }; 813 814 en_fp_rails: en-fp-rails-state { 815 pins = "gpio77"; 816 function = "gpio"; 817 bias-disable; 818 drive-strength = <2>; 819 output-high; 820 }; 821 822 en_pp3300_codec: en-pp3300-codec-state { 823 pins = "gpio105"; 824 function = "gpio"; 825 bias-disable; 826 drive-strength = <2>; 827 }; 828 829 en_pp3300_dx_edp: en-pp3300-dx-edp-state { 830 pins = "gpio80"; 831 function = "gpio"; 832 bias-disable; 833 drive-strength = <2>; 834 }; 835 836 fp_rst_l: fp-rst-l-state { 837 pins = "gpio78"; 838 function = "gpio"; 839 bias-disable; 840 drive-strength = <2>; 841 }; 842 843 fp_to_ap_irq_l: fp-to-ap-irq-l-state { 844 pins = "gpio61"; 845 function = "gpio"; 846 /* Has external pullup */ 847 bias-disable; 848 }; 849 850 fpmcu_boot0: fpmcu-boot0-state { 851 pins = "gpio68"; 852 function = "gpio"; 853 bias-disable; 854 }; 855 856 gsc_ap_int_odl: gsc-ap-int-odl-state { 857 pins = "gpio104"; 858 function = "gpio"; 859 bias-pull-up; 860 }; 861 862 hp_irq: hp-irq-state { 863 pins = "gpio101"; 864 function = "gpio"; 865 bias-pull-up; 866 }; 867 868 hub_en: hub-en-state { 869 pins = "gpio157"; 870 function = "gpio"; 871 bias-disable; 872 drive-strength = <2>; 873 }; 874 875 pe_wake_odl: pe-wake-odl-state { 876 pins = "gpio3"; 877 function = "gpio"; 878 /* Has external pull */ 879 bias-disable; 880 drive-strength = <2>; 881 }; 882 883 /* For ap_spi_fp */ 884 qup_spi9_cs_gpio_init_high: qup-spi9-cs-gpio-init-high-state { 885 pins = "gpio39"; 886 function = "gpio"; 887 output-high; 888 }; 889 890 /* For ap_ec_spi */ 891 qup_spi10_cs_gpio_init_high: qup-spi10-cs-gpio-init-high-state { 892 pins = "gpio43"; 893 function = "gpio"; 894 output-high; 895 }; 896 897 sar0_irq_odl: sar0-irq-odl-state { 898 pins = "gpio141"; 899 function = "gpio"; 900 bias-pull-up; 901 }; 902 903 sar1_irq_odl: sar1-irq-odl-state { 904 pins = "gpio140"; 905 function = "gpio"; 906 bias-pull-up; 907 }; 908 909 sd_cd_odl: sd-cd-odl-state { 910 pins = "gpio91"; 911 function = "gpio"; 912 bias-pull-up; 913 }; 914 915 ssd_en: ssd-en-state { 916 pins = "gpio51"; 917 function = "gpio"; 918 bias-disable; 919 drive-strength = <2>; 920 }; 921 922 ssd_rst_l: ssd-rst-l-state { 923 pins = "gpio2"; 924 function = "gpio"; 925 bias-disable; 926 drive-strength = <2>; 927 output-low; 928 }; 929 930 tp_int_odl: tp-int-odl-state { 931 pins = "gpio7"; 932 function = "gpio"; 933 /* Has external pullup */ 934 bias-disable; 935 }; 936 937 wf_cam_en: wf-cam-en-state { 938 pins = "gpio119"; 939 function = "gpio"; 940 /* Has external pulldown */ 941 bias-disable; 942 drive-strength = <2>; 943 }; 944}; 945