1// SPDX-License-Identifier: GPL-2.0 2#include <dt-bindings/iio/qcom,spmi-vadc.h> 3#include <dt-bindings/input/linux-event-codes.h> 4#include <dt-bindings/interrupt-controller/irq.h> 5#include <dt-bindings/spmi/spmi.h> 6 7&spmi_bus { 8 9 pm8916_0: pmic@0 { 10 compatible = "qcom,pm8916", "qcom,spmi-pmic"; 11 reg = <0x0 SPMI_USID>; 12 #address-cells = <1>; 13 #size-cells = <0>; 14 15 pon@800 { 16 compatible = "qcom,pm8916-pon"; 17 reg = <0x800>; 18 mode-bootloader = <0x2>; 19 mode-recovery = <0x1>; 20 21 pwrkey { 22 compatible = "qcom,pm8941-pwrkey"; 23 interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; 24 debounce = <15625>; 25 bias-pull-up; 26 linux,code = <KEY_POWER>; 27 }; 28 29 pm8916_resin: resin { 30 compatible = "qcom,pm8941-resin"; 31 interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; 32 debounce = <15625>; 33 bias-pull-up; 34 status = "disabled"; 35 }; 36 37 watchdog { 38 compatible = "qcom,pm8916-wdt"; 39 interrupts = <0x0 0x8 6 IRQ_TYPE_EDGE_RISING>; 40 timeout-sec = <60>; 41 }; 42 }; 43 44 pm8916_charger: charger@1000 { 45 compatible = "qcom,pm8916-lbc"; 46 reg = <0x1000>, <0x1200>, <0x1300>, <0x1600>; 47 reg-names = "chgr", "bat_if", "usb", "misc"; 48 49 interrupts = <0x0 0x10 0 IRQ_TYPE_EDGE_BOTH>, 50 <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>, 51 <0x0 0x10 6 IRQ_TYPE_EDGE_BOTH>, 52 <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>, 53 <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>, 54 <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>, 55 <0x0 0x13 0 IRQ_TYPE_EDGE_BOTH>, 56 <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>, 57 <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>, 58 <0x0 0x13 4 IRQ_TYPE_EDGE_BOTH>; 59 interrupt-names = "vbat_det", 60 "fast_chg", 61 "chg_fail", 62 "chg_done", 63 "bat_pres", 64 "temp_ok", 65 "coarse_det", 66 "usb_vbus", 67 "chg_gone", 68 "overtemp"; 69 70 status = "disabled"; 71 }; 72 73 pm8916_usbin: usb-detect@1300 { 74 compatible = "qcom,pm8941-misc"; 75 reg = <0x1300>; 76 interrupts = <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>; 77 interrupt-names = "usb_vbus"; 78 status = "disabled"; 79 }; 80 81 pm8916_temp: temp-alarm@2400 { 82 compatible = "qcom,spmi-temp-alarm"; 83 reg = <0x2400>; 84 interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>; 85 io-channels = <&pm8916_vadc VADC_DIE_TEMP>; 86 io-channel-names = "thermal"; 87 #thermal-sensor-cells = <0>; 88 }; 89 90 pm8916_vadc: adc@3100 { 91 compatible = "qcom,spmi-vadc"; 92 reg = <0x3100>; 93 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 94 #address-cells = <1>; 95 #size-cells = <0>; 96 #io-channel-cells = <1>; 97 98 channel@0 { 99 reg = <VADC_USBIN>; 100 qcom,pre-scaling = <1 10>; 101 }; 102 channel@7 { 103 reg = <VADC_VSYS>; 104 qcom,pre-scaling = <1 3>; 105 }; 106 channel@8 { 107 reg = <VADC_DIE_TEMP>; 108 }; 109 channel@9 { 110 reg = <VADC_REF_625MV>; 111 }; 112 channel@a { 113 reg = <VADC_REF_1250MV>; 114 }; 115 channel@e { 116 reg = <VADC_GND_REF>; 117 }; 118 channel@f { 119 reg = <VADC_VDD_VADC>; 120 }; 121 }; 122 123 pm8916_bms: battery@4000 { 124 compatible = "qcom,pm8916-bms-vm"; 125 reg = <0x4000>; 126 interrupts = <0x0 0x40 0 IRQ_TYPE_EDGE_RISING>, 127 <0x0 0x40 1 IRQ_TYPE_EDGE_RISING>, 128 <0x0 0x40 2 IRQ_TYPE_EDGE_RISING>, 129 <0x0 0x40 3 IRQ_TYPE_EDGE_RISING>, 130 <0x0 0x40 4 IRQ_TYPE_EDGE_RISING>, 131 <0x0 0x40 5 IRQ_TYPE_EDGE_RISING>; 132 interrupt-names = "cv_leave", 133 "cv_enter", 134 "ocv_good", 135 "ocv_thr", 136 "fifo", 137 "state_chg"; 138 139 status = "disabled"; 140 }; 141 142 rtc@6000 { 143 compatible = "qcom,pm8941-rtc"; 144 reg = <0x6000>, <0x6100>; 145 reg-names = "rtc", "alarm"; 146 interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; 147 }; 148 149 pm8916_mpps: mpps@a000 { 150 compatible = "qcom,pm8916-mpp", "qcom,spmi-mpp"; 151 reg = <0xa000>; 152 gpio-controller; 153 #gpio-cells = <2>; 154 gpio-ranges = <&pm8916_mpps 0 0 4>; 155 interrupt-controller; 156 #interrupt-cells = <2>; 157 }; 158 159 pm8916_gpios: gpio@c000 { 160 compatible = "qcom,pm8916-gpio", "qcom,spmi-gpio"; 161 reg = <0xc000>; 162 gpio-controller; 163 gpio-ranges = <&pm8916_gpios 0 0 4>; 164 #gpio-cells = <2>; 165 interrupt-controller; 166 #interrupt-cells = <2>; 167 }; 168 }; 169 170 pm8916_1: pmic@1 { 171 compatible = "qcom,pm8916", "qcom,spmi-pmic"; 172 reg = <0x1 SPMI_USID>; 173 #address-cells = <1>; 174 #size-cells = <0>; 175 176 pm8916_pwm: pwm { 177 compatible = "qcom,pm8916-pwm"; 178 179 #pwm-cells = <2>; 180 181 status = "disabled"; 182 }; 183 184 pm8916_vib: vibrator@c000 { 185 compatible = "qcom,pm8916-vib"; 186 reg = <0xc000>; 187 status = "disabled"; 188 }; 189 190 pm8916_codec: audio-codec@f000 { 191 compatible = "qcom,pm8916-wcd-analog-codec"; 192 reg = <0xf000>; 193 interrupt-parent = <&spmi_bus>; 194 interrupts = <0x1 0xf0 0x0 IRQ_TYPE_NONE>, 195 <0x1 0xf0 0x1 IRQ_TYPE_NONE>, 196 <0x1 0xf0 0x2 IRQ_TYPE_NONE>, 197 <0x1 0xf0 0x3 IRQ_TYPE_NONE>, 198 <0x1 0xf0 0x4 IRQ_TYPE_NONE>, 199 <0x1 0xf0 0x5 IRQ_TYPE_NONE>, 200 <0x1 0xf0 0x6 IRQ_TYPE_NONE>, 201 <0x1 0xf0 0x7 IRQ_TYPE_NONE>, 202 <0x1 0xf1 0x0 IRQ_TYPE_NONE>, 203 <0x1 0xf1 0x1 IRQ_TYPE_NONE>, 204 <0x1 0xf1 0x2 IRQ_TYPE_NONE>, 205 <0x1 0xf1 0x3 IRQ_TYPE_NONE>, 206 <0x1 0xf1 0x4 IRQ_TYPE_NONE>, 207 <0x1 0xf1 0x5 IRQ_TYPE_NONE>; 208 interrupt-names = "cdc_spk_cnp_int", 209 "cdc_spk_clip_int", 210 "cdc_spk_ocp_int", 211 "mbhc_ins_rem_det1", 212 "mbhc_but_rel_det", 213 "mbhc_but_press_det", 214 "mbhc_ins_rem_det", 215 "mbhc_switch_int", 216 "cdc_ear_ocp_int", 217 "cdc_hphr_ocp_int", 218 "cdc_hphl_ocp_det", 219 "cdc_ear_cnp_int", 220 "cdc_hphr_cnp_int", 221 "cdc_hphl_cnp_int"; 222 #sound-dai-cells = <1>; 223 status = "disabled"; 224 }; 225 }; 226}; 227