1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. 4 * Copyright (c) 2019, Linaro Limited 5 */ 6 7#include <dt-bindings/input/input.h> 8#include <dt-bindings/interrupt-controller/irq.h> 9#include <dt-bindings/spmi/spmi.h> 10#include <dt-bindings/iio/qcom,spmi-vadc.h> 11 12/ { 13 thermal-zones { 14 pm8150-thermal { 15 polling-delay-passive = <100>; 16 polling-delay = <0>; 17 18 thermal-sensors = <&pm8150_temp>; 19 20 trips { 21 trip0 { 22 temperature = <95000>; 23 hysteresis = <0>; 24 type = "passive"; 25 }; 26 27 trip1 { 28 temperature = <115000>; 29 hysteresis = <0>; 30 type = "hot"; 31 }; 32 33 trip2 { 34 temperature = <145000>; 35 hysteresis = <0>; 36 type = "critical"; 37 }; 38 }; 39 }; 40 }; 41}; 42 43&spmi_bus { 44 pm8150_0: pmic@0 { 45 compatible = "qcom,pm8150", "qcom,spmi-pmic"; 46 reg = <0x0 SPMI_USID>; 47 #address-cells = <1>; 48 #size-cells = <0>; 49 50 pon: power-on@800 { 51 compatible = "qcom,pm8916-pon"; 52 reg = <0x0800>; 53 pwrkey { 54 compatible = "qcom,pm8941-pwrkey"; 55 interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; 56 debounce = <15625>; 57 bias-pull-up; 58 linux,code = <KEY_POWER>; 59 60 status = "disabled"; 61 }; 62 }; 63 64 pm8150_temp: temp-alarm@2400 { 65 compatible = "qcom,spmi-temp-alarm"; 66 reg = <0x2400>; 67 interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; 68 io-channels = <&pm8150_adc ADC5_DIE_TEMP>; 69 io-channel-names = "thermal"; 70 #thermal-sensor-cells = <0>; 71 }; 72 73 pm8150_adc: adc@3100 { 74 compatible = "qcom,spmi-adc5"; 75 reg = <0x3100>; 76 #address-cells = <1>; 77 #size-cells = <0>; 78 #io-channel-cells = <1>; 79 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 80 81 ref-gnd@0 { 82 reg = <ADC5_REF_GND>; 83 qcom,pre-scaling = <1 1>; 84 label = "ref_gnd"; 85 }; 86 87 vref-1p25@1 { 88 reg = <ADC5_1P25VREF>; 89 qcom,pre-scaling = <1 1>; 90 label = "vref_1p25"; 91 }; 92 93 die-temp@6 { 94 reg = <ADC5_DIE_TEMP>; 95 qcom,pre-scaling = <1 1>; 96 label = "die_temp"; 97 }; 98 }; 99 100 pm8150_adc_tm: adc-tm@3500 { 101 compatible = "qcom,spmi-adc-tm5"; 102 reg = <0x3500>; 103 interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; 104 #thermal-sensor-cells = <1>; 105 #address-cells = <1>; 106 #size-cells = <0>; 107 status = "disabled"; 108 }; 109 110 rtc@6000 { 111 compatible = "qcom,pm8941-rtc"; 112 reg = <0x6000>; 113 reg-names = "rtc", "alarm"; 114 interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; 115 }; 116 117 pm8150_gpios: gpio@c000 { 118 compatible = "qcom,pm8150-gpio"; 119 reg = <0xc000>; 120 gpio-controller; 121 #gpio-cells = <2>; 122 interrupt-controller; 123 #interrupt-cells = <2>; 124 }; 125 }; 126 127 pmic@1 { 128 compatible = "qcom,pm8150", "qcom,spmi-pmic"; 129 reg = <0x1 SPMI_USID>; 130 #address-cells = <1>; 131 #size-cells = <0>; 132 }; 133}; 134