1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. 4 * Copyright (c) 2019, Linaro Limited 5 */ 6 7#include <dt-bindings/input/input.h> 8#include <dt-bindings/interrupt-controller/irq.h> 9#include <dt-bindings/spmi/spmi.h> 10#include <dt-bindings/iio/qcom,spmi-vadc.h> 11 12/ { 13 thermal-zones { 14 pm8150-thermal { 15 polling-delay-passive = <100>; 16 polling-delay = <0>; 17 18 thermal-sensors = <&pm8150_temp>; 19 20 trips { 21 trip0 { 22 temperature = <95000>; 23 hysteresis = <0>; 24 type = "passive"; 25 }; 26 27 trip1 { 28 temperature = <115000>; 29 hysteresis = <0>; 30 type = "hot"; 31 }; 32 33 trip2 { 34 temperature = <145000>; 35 hysteresis = <0>; 36 type = "critical"; 37 }; 38 }; 39 }; 40 }; 41}; 42 43&spmi_bus { 44 pm8150_0: pmic@0 { 45 compatible = "qcom,pm8150", "qcom,spmi-pmic"; 46 reg = <0x0 SPMI_USID>; 47 #address-cells = <1>; 48 #size-cells = <0>; 49 50 pon: pon@800 { 51 compatible = "qcom,pm8998-pon"; 52 reg = <0x0800>; 53 mode-bootloader = <0x2>; 54 mode-recovery = <0x1>; 55 56 pon_pwrkey: pwrkey { 57 compatible = "qcom,pm8941-pwrkey"; 58 interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; 59 debounce = <15625>; 60 bias-pull-up; 61 linux,code = <KEY_POWER>; 62 63 status = "disabled"; 64 }; 65 66 pon_resin: resin { 67 compatible = "qcom,pm8941-resin"; 68 interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>; 69 debounce = <15625>; 70 bias-pull-up; 71 72 status = "disabled"; 73 }; 74 }; 75 76 pm8150_temp: temp-alarm@2400 { 77 compatible = "qcom,spmi-temp-alarm"; 78 reg = <0x2400>; 79 interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; 80 io-channels = <&pm8150_adc ADC5_DIE_TEMP>; 81 io-channel-names = "thermal"; 82 #thermal-sensor-cells = <0>; 83 }; 84 85 pm8150_adc: adc@3100 { 86 compatible = "qcom,spmi-adc5"; 87 reg = <0x3100>; 88 #address-cells = <1>; 89 #size-cells = <0>; 90 #io-channel-cells = <1>; 91 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 92 93 ref-gnd@0 { 94 reg = <ADC5_REF_GND>; 95 qcom,pre-scaling = <1 1>; 96 label = "ref_gnd"; 97 }; 98 99 vref-1p25@1 { 100 reg = <ADC5_1P25VREF>; 101 qcom,pre-scaling = <1 1>; 102 label = "vref_1p25"; 103 }; 104 105 die-temp@6 { 106 reg = <ADC5_DIE_TEMP>; 107 qcom,pre-scaling = <1 1>; 108 label = "die_temp"; 109 }; 110 }; 111 112 pm8150_adc_tm: adc-tm@3500 { 113 compatible = "qcom,spmi-adc-tm5"; 114 reg = <0x3500>; 115 interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; 116 #thermal-sensor-cells = <1>; 117 #address-cells = <1>; 118 #size-cells = <0>; 119 status = "disabled"; 120 }; 121 122 rtc@6000 { 123 compatible = "qcom,pm8941-rtc"; 124 reg = <0x6000>, <0x6100>; 125 reg-names = "rtc", "alarm"; 126 interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; 127 }; 128 129 pm8150_gpios: gpio@c000 { 130 compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio"; 131 reg = <0xc000>; 132 gpio-controller; 133 gpio-ranges = <&pm8150_gpios 0 0 10>; 134 #gpio-cells = <2>; 135 interrupt-controller; 136 #interrupt-cells = <2>; 137 }; 138 }; 139 140 pmic@1 { 141 compatible = "qcom,pm8150", "qcom,spmi-pmic"; 142 reg = <0x1 SPMI_USID>; 143 #address-cells = <1>; 144 #size-cells = <0>; 145 }; 146}; 147