1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2020, Konrad Dybcio 4 */ 5 6#include <dt-bindings/iio/qcom,spmi-vadc.h> 7#include <dt-bindings/input/linux-event-codes.h> 8#include <dt-bindings/interrupt-controller/irq.h> 9#include <dt-bindings/spmi/spmi.h> 10#include <dt-bindings/thermal/thermal.h> 11 12/ { 13 thermal-zones { 14 pm660-thermal { 15 polling-delay-passive = <250>; 16 polling-delay = <1000>; 17 18 thermal-sensors = <&pm660_temp>; 19 20 trips { 21 pm660_alert0: pm660-alert0 { 22 temperature = <95000>; 23 hysteresis = <2000>; 24 type = "passive"; 25 }; 26 pm660_crit: pm660-crit { 27 temperature = <125000>; 28 hysteresis = <2000>; 29 type = "critical"; 30 }; 31 }; 32 }; 33 }; 34}; 35 36&spmi_bus { 37 38 pmic@0 { 39 compatible = "qcom,pm660", "qcom,spmi-pmic"; 40 reg = <0x0 SPMI_USID>; 41 #address-cells = <1>; 42 #size-cells = <0>; 43 44 rtc@6000 { 45 compatible = "qcom,pm8941-rtc"; 46 reg = <0x6000>, <0x6100>; 47 reg-names = "rtc", "alarm"; 48 interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; 49 }; 50 51 pon: pon@800 { 52 compatible = "qcom,pm8998-pon"; 53 reg = <0x800>; 54 mode-bootloader = <0x2>; 55 mode-recovery = <0x1>; 56 57 pon_pwrkey: pwrkey { 58 compatible = "qcom,pm8941-pwrkey"; 59 interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; 60 debounce = <15625>; 61 bias-pull-up; 62 linux,code = <KEY_POWER>; 63 64 status = "disabled"; 65 }; 66 67 pon_resin: resin { 68 compatible = "qcom,pm8941-resin"; 69 interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; 70 debounce = <15625>; 71 bias-pull-up; 72 73 status = "disabled"; 74 }; 75 }; 76 77 pm660_temp: temp-alarm@2400 { 78 compatible = "qcom,spmi-temp-alarm"; 79 reg = <0x2400>; 80 interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>; 81 io-channels = <&pm660_adc ADC5_DIE_TEMP>; 82 io-channel-names = "thermal"; 83 #thermal-sensor-cells = <0>; 84 }; 85 86 pm660_adc: adc@3100 { 87 compatible = "qcom,spmi-adc-rev2"; 88 reg = <0x3100>; 89 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; 90 #address-cells = <1>; 91 #size-cells = <0>; 92 #io-channel-cells = <1>; 93 94 channel@0 { 95 reg = <ADC5_REF_GND>; 96 qcom,decimation = <1024>; 97 qcom,pre-scaling = <1 1>; 98 label = "ref_gnd"; 99 }; 100 101 channel@1 { 102 reg = <ADC5_1P25VREF>; 103 qcom,decimation = <1024>; 104 qcom,pre-scaling = <1 1>; 105 label = "vref_1p25"; 106 }; 107 108 channel@6 { 109 reg = <ADC5_DIE_TEMP>; 110 qcom,decimation = <1024>; 111 qcom,pre-scaling = <1 1>; 112 label = "die_temp"; 113 }; 114 115 channel@4c { 116 reg = <ADC5_XO_THERM_100K_PU>; 117 qcom,pre-scaling = <1 1>; 118 qcom,decimation = <1024>; 119 qcom,hw-settle-time = <200>; 120 qcom,ratiometric; 121 label = "xo_therm"; 122 }; 123 124 channel@4d { 125 reg = <ADC5_AMUX_THM1_100K_PU>; 126 qcom,pre-scaling = <1 1>; 127 qcom,decimation = <1024>; 128 qcom,hw-settle-time = <200>; 129 qcom,ratiometric; 130 label = "msm_therm"; 131 }; 132 133 channel@4e { 134 reg = <ADC5_AMUX_THM2_100K_PU>; 135 qcom,pre-scaling = <1 1>; 136 qcom,decimation = <1024>; 137 qcom,hw-settle-time = <200>; 138 qcom,ratiometric; 139 label = "emmc_therm"; 140 }; 141 142 channel@4f { 143 reg = <ADC5_AMUX_THM3_100K_PU>; 144 qcom,pre-scaling = <1 1>; 145 qcom,decimation = <1024>; 146 qcom,hw-settle-time = <200>; 147 qcom,ratiometric; 148 label = "pa_therm0"; 149 }; 150 151 channel@50 { 152 reg = <ADC5_AMUX_THM4_100K_PU>; 153 qcom,pre-scaling = <1 1>; 154 qcom,decimation = <1024>; 155 qcom,hw-settle-time = <200>; 156 qcom,ratiometric; 157 label = "pa_therm1"; 158 }; 159 160 channel@51 { 161 reg = <ADC5_AMUX_THM5_100K_PU>; 162 qcom,pre-scaling = <1 1>; 163 qcom,decimation = <1024>; 164 qcom,hw-settle-time = <200>; 165 qcom,ratiometric; 166 label = "quiet_therm"; 167 }; 168 169 channel@83 { 170 reg = <ADC5_VPH_PWR>; 171 qcom,decimation = <1024>; 172 qcom,pre-scaling = <1 3>; 173 label = "vph_pwr"; 174 }; 175 176 channel@85 { 177 reg = <ADC5_VCOIN>; 178 qcom,decimation = <1024>; 179 qcom,pre-scaling = <1 3>; 180 label = "vcoin"; 181 }; 182 }; 183 184 pm660_gpios: gpio@c000 { 185 compatible = "qcom,pm660-gpio", "qcom,spmi-gpio"; 186 reg = <0xc000>; 187 gpio-controller; 188 gpio-ranges = <&pm660_gpios 0 0 13>; 189 #gpio-cells = <2>; 190 interrupt-controller; 191 #interrupt-cells = <2>; 192 }; 193 }; 194 195 pmic@1 { 196 compatible = "qcom,pm660", "qcom,spmi-pmic"; 197 reg = <0x1 SPMI_USID>; 198 #address-cells = <1>; 199 #size-cells = <0>; 200 201 pm660_spmi_regulators: regulators { 202 compatible = "qcom,pm660-regulators"; 203 }; 204 }; 205}; 206