1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * Copyright (c) 2021, AngeloGioacchino Del Regno 4 * <angelogioacchino.delregno@somainline.org> 5 * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org> 6 */ 7 8#include "msm8996.dtsi" 9#include "pm8994.dtsi" 10#include "pmi8994.dtsi" 11#include "pmi8996.dtsi" 12#include <dt-bindings/input/input.h> 13#include <dt-bindings/gpio/gpio.h> 14#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> 15#include <dt-bindings/pinctrl/qcom,pmic-mpp.h> 16 17/delete-node/ &adsp_mem; 18/delete-node/ &slpi_mem; 19/delete-node/ &venus_mem; 20/delete-node/ &gpu_mem; 21 22/ { 23 qcom,msm-id = <246 0x30001>; /* MSM8996 V3.1 (Final) */ 24 qcom,board-id = <8 0>; 25 26 chosen { 27 bootargs = "maxcpus=2"; 28 }; 29 30 reserved-memory { 31 ramoops@a7f00000 { 32 compatible = "ramoops"; 33 reg = <0 0xa7f00000 0 0x100000>; 34 record-size = <0x20000>; 35 console-size = <0x40000>; 36 ftrace-size = <0x20000>; 37 pmsg-size = <0x20000>; 38 ecc-size = <16>; 39 }; 40 41 adsp_mem: adsp@8ea00000 { 42 reg = <0x0 0x8ea00000 0x0 0x1a00000>; 43 no-map; 44 }; 45 46 gpu_mem: gpu@90400000 { 47 compatible = "shared-dma-pool"; 48 reg = <0x0 0x90400000 0x0 0x2000>; 49 no-map; 50 }; 51 52 slpi_mem: memory@90500000 { 53 reg = <0 0x90500000 0 0xa00000>; 54 no-map; 55 }; 56 57 venus_mem: memory@90f00000 { 58 reg = <0 0x90f00000 0 0x500000>; 59 no-map; 60 }; 61 }; 62 63 panel_tvdd: tvdd-regulator { 64 compatible = "regulator-fixed"; 65 regulator-name = "panel_tvdd"; 66 gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; 67 pinctrl-0 = <&tp_vddio_en>; 68 pinctrl-names = "default"; 69 }; 70 71 usb3_id: usb3-id { 72 compatible = "linux,extcon-usb-gpio"; 73 id-gpio = <&tlmm 25 GPIO_ACTIVE_LOW>; 74 pinctrl-names = "default"; 75 pinctrl-0 = <&usb_detect>; 76 }; 77 78 vph_pwr: vph-pwr-regulator { 79 compatible = "regulator-fixed"; 80 regulator-min-microvolt = <3700000>; 81 regulator-max-microvolt = <3700000>; 82 regulator-name = "vph_pwr"; 83 regulator-always-on; 84 regulator-boot-on; 85 }; 86 87 wlan_en: wlan-en-1-8v { 88 compatible = "regulator-fixed"; 89 regulator-name = "wlan-en-regulator"; 90 regulator-min-microvolt = <1800000>; 91 regulator-max-microvolt = <1800000>; 92 gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>; 93 pinctrl-names = "default"; 94 pinctrl-0 = <&wl_reg_on>; 95 96 /* WLAN card specific delay */ 97 startup-delay-us = <70000>; 98 enable-active-high; 99 }; 100}; 101 102&blsp1_i2c3 { 103 clock-frequency = <355000>; 104 status = "okay"; 105 106 tof_sensor: vl53l0x@29 { 107 compatible = "st,vl53l0x"; 108 reg = <0x29>; 109 }; 110}; 111 112&blsp1_uart2 { 113 status = "okay"; 114}; 115 116&blsp2_i2c5 { 117 clock-frequency = <355000>; 118 status = "okay"; 119 120 /* FUSB301 USB-C controller */ 121}; 122 123&blsp2_i2c6 { 124 clock-frequency = <355000>; 125 status = "okay"; 126 127 synaptics@2c { 128 compatible = "syna,rmi4-i2c"; 129 reg = <0x2c>; 130 interrupt-parent = <&tlmm>; 131 interrupts = <125 IRQ_TYPE_EDGE_FALLING>; 132 vdd-supply = <&panel_tvdd>; 133 134 syna,reset-delay-ms = <220>; 135 syna,startup-delay-ms = <220>; 136 #address-cells = <1>; 137 #size-cells = <0>; 138 139 rmi4-f01@1 { 140 reg = <0x1>; 141 syna,nosleep-mode = <1>; 142 }; 143 144 rmi4-f11@11 { 145 reg = <0x11>; 146 syna,sensor-type = <1>; 147 }; 148 }; 149}; 150 151&blsp2_uart2 { 152 status = "okay"; 153}; 154 155&camera0_mclk { 156 drive-strength = <2>; 157 output-low; 158}; 159 160&camera0_pwdn { 161 drive-strength = <2>; 162 output-low; 163}; 164 165&camera0_rst { 166 pins = "gpio30"; 167 drive-strength = <2>; 168 output-low; 169}; 170 171&camera2_mclk { 172 drive-strength = <2>; 173 output-low; 174}; 175 176&camera2_rst { 177 drive-strength = <2>; 178 output-low; 179}; 180 181&hsusb_phy1 { 182 vdd-supply = <&pm8994_l28>; 183 vdda-pll-supply = <&pm8994_l12>; 184 vdda-phy-dpdm-supply = <&pm8994_l24>; 185 status = "okay"; 186}; 187 188&mmcc { 189 vdd-gfx-supply = <&vdd_gfx>; 190}; 191 192&pcie0 { 193 perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>; 194 wake-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>; 195 vddpe-3v3-supply = <&wlan_en>; 196 vdda-supply = <&pm8994_l28>; 197 status = "okay"; 198}; 199 200&pcie_phy { 201 vdda-phy-supply = <&pm8994_l28>; 202 vdda-pll-supply = <&pm8994_l12>; 203 status = "okay"; 204}; 205 206&pm8994_gpios { 207 pinctrl-names = "default"; 208 pinctrl-0 = <&pm8994_gpios_defaults>; 209 gpio-line-names = 210 "NC", 211 "VOL_DOWN_N", 212 "VOL_UP_N", 213 "SNAPSHOT_N", 214 "FOCUS_N", 215 "NC", 216 "NFC_VEN", 217 "NC", 218 "NC", 219 "NC", 220 "NC", 221 "NC", 222 "EAR_EN", 223 "NC", 224 "PM_DIVCLK1", 225 "PMI_CLK", 226 "NC", 227 "WL_SLEEP_CLK", 228 "NC", 229 "PMIC_SPON", 230 "UIM_BATT_ALARM", 231 "PMK_SLEEP_CLK"; 232 233 /* 234 * We don't yet know for sure which GPIOs are of our interest, but what 235 * we do know is that if a vendor sets the pins to a non-default state, there's 236 * probably a reason for it, and just to be on the safe side, we follow suit. 237 */ 238 pm8994_gpios_defaults: pm8994-gpios-default-state { 239 pm8994-gpio1-nc-pins { 240 pins = "gpio1"; 241 function = PMIC_GPIO_FUNC_NORMAL; 242 drive-push-pull; 243 bias-high-impedance; 244 }; 245 246 vol-down-n-pins { 247 pins = "gpio2"; 248 function = PMIC_GPIO_FUNC_NORMAL; 249 drive-push-pull; 250 input-enable; 251 bias-pull-up; 252 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; 253 power-source = <PM8994_GPIO_S4>; 254 }; 255 256 vol-up-n-pins { 257 pins = "gpio3"; 258 function = PMIC_GPIO_FUNC_NORMAL; 259 drive-push-pull; 260 input-enable; 261 bias-pull-up; 262 power-source = <PM8994_GPIO_S4>; 263 }; 264 265 camera-snapshot-n-pins { 266 pins = "gpio4"; 267 function = PMIC_GPIO_FUNC_NORMAL; 268 drive-push-pull; 269 input-enable; 270 bias-pull-up; 271 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; 272 power-source = <PM8994_GPIO_S4>; 273 }; 274 275 camera-focus-n-pins { 276 pins = "gpio5"; 277 function = PMIC_GPIO_FUNC_NORMAL; 278 drive-push-pull; 279 input-enable; 280 bias-pull-up; 281 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; 282 power-source = <PM8994_GPIO_S4>; 283 }; 284 285 pm8994-gpio6-nc-pins { 286 pins = "gpio6"; 287 function = PMIC_GPIO_FUNC_NORMAL; 288 drive-push-pull; 289 bias-high-impedance; 290 power-source = <PM8994_GPIO_VPH>; 291 }; 292 293 nfc-download-pins { 294 pins = "gpio7"; 295 function = PMIC_GPIO_FUNC_NORMAL; 296 output-low; 297 drive-push-pull; 298 bias-disable; 299 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; 300 power-source = <PM8994_GPIO_S4>; 301 }; 302 303 pm8994-gpio8-nc-pins { 304 pins = "gpio8"; 305 function = PMIC_GPIO_FUNC_NORMAL; 306 output-low; 307 drive-push-pull; 308 bias-high-impedance; 309 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; 310 power-source = <PM8994_GPIO_VPH>; 311 }; 312 313 pm8994-gpio9-nc-pins { 314 pins = "gpio9"; 315 function = PMIC_GPIO_FUNC_NORMAL; 316 output-high; 317 drive-push-pull; 318 bias-high-impedance; 319 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; 320 power-source = <PM8994_GPIO_VPH>; 321 }; 322 323 nfc-clock-pins { 324 pins = "gpio10"; 325 function = PMIC_GPIO_FUNC_NORMAL; 326 input-enable; 327 drive-push-pull; 328 bias-pull-down; 329 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; 330 power-source = <PM8994_GPIO_S4>; 331 }; 332 333 pm8994-gpio11-nc-pins { 334 pins = "gpio11"; 335 function = PMIC_GPIO_FUNC_NORMAL; 336 drive-push-pull; 337 bias-high-impedance; 338 power-source = <PM8994_GPIO_VPH>; 339 }; 340 341 pm8994-gpio12-nc-pins { 342 pins = "gpio12"; 343 function = PMIC_GPIO_FUNC_NORMAL; 344 drive-push-pull; 345 bias-high-impedance; 346 power-source = <PM8994_GPIO_VPH>; 347 }; 348 349 ear-enable-pins { 350 pins = "gpio13"; 351 function = PMIC_GPIO_FUNC_NORMAL; 352 output-high; 353 drive-push-pull; 354 bias-disable; 355 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; 356 power-source = <PM8994_GPIO_S4>; 357 }; 358 359 pm8994-gpio14-nc-pins { 360 pins = "gpio14"; 361 function = PMIC_GPIO_FUNC_NORMAL; 362 drive-push-pull; 363 input-enable; 364 bias-high-impedance; 365 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; 366 power-source = <PM8994_GPIO_VPH>; 367 }; 368 369 pm-divclk1-gpio-pins { 370 pins = "gpio15"; 371 function = "func1"; 372 output-high; 373 drive-push-pull; 374 bias-high-impedance; 375 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; 376 power-source = <PM8994_GPIO_VPH>; 377 }; 378 379 pmi-clk-gpio-pins { 380 pins = "gpio16"; 381 function = PMIC_GPIO_FUNC_NORMAL; 382 drive-push-pull; 383 }; 384 385 pm8994-gpio17-nc-pins { 386 pins = "gpio17"; 387 function = PMIC_GPIO_FUNC_NORMAL; 388 drive-push-pull; 389 bias-high-impedance; 390 power-source = <PM8994_GPIO_VPH>; 391 }; 392 393 rome-sleep-pins { 394 pins = "gpio18"; 395 function = PMIC_GPIO_FUNC_FUNC2; 396 output-low; 397 drive-push-pull; 398 bias-disable; 399 qcom,drive-strength = <PMIC_GPIO_STRENGTH_MED>; 400 power-source = <PM8994_GPIO_S4>; 401 }; 402 403 pm8994-gpio19-nc-pins { 404 pins = "gpio19"; 405 function = PMIC_GPIO_FUNC_NORMAL; 406 output-low; 407 drive-push-pull; 408 bias-high-impedance; 409 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; 410 power-source = <PM8994_GPIO_VPH>; 411 }; 412 413 pm8994-gpio22-nc-pins { 414 pins = "gpio22"; 415 function = PMIC_GPIO_FUNC_NORMAL; 416 drive-push-pull; 417 bias-high-impedance; 418 power-source = <PM8994_GPIO_VPH>; 419 }; 420 }; 421}; 422 423&pm8994_mpps { 424 pinctrl-names = "default"; 425 pinctrl-0 = <&pm8994_mpps_defaults>; 426 427 gpio-line-names = 428 "SDC_UIM_VBIAS", 429 "LCD_ID_ADC", 430 "VREF_DACX", 431 "NC", 432 "FLASH_THERM", 433 "NC", 434 "NC", 435 "RF_ID"; 436 437 pm8994_mpps_defaults: pm8994-mpps-default-state { 438 lcd-id_adc-mpp-pins { 439 pins = "mpp2"; 440 function = "analog"; 441 input-enable; 442 qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH6>; 443 }; 444 445 pm-mpp4-nc-pins { 446 pins = "mpp4"; 447 function = "digital"; 448 bias-high-impedance; 449 power-source = <PM8994_GPIO_VPH>; 450 }; 451 452 flash-therm-mpp-pins { 453 pins = "mpp5"; 454 function = "analog"; 455 input-enable; 456 qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>; 457 }; 458 459 mpp6-nc-pins { 460 pins = "mpp6"; 461 function = "digital"; 462 bias-high-impedance; 463 }; 464 465 rf-id-mpp-pins { 466 pins = "mpp8"; 467 function = "analog"; 468 input-enable; 469 qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH8>; 470 }; 471 }; 472}; 473 474&pm8994_resin { 475 linux,code = <KEY_VOLUMEUP>; 476 status = "okay"; 477}; 478 479&pmi8994_gpios { 480 pinctrl-names = "default"; 481 pinctrl-0 = <&pmi8994_gpios_defaults>; 482 483 gpio-line-names = 484 "VIB_LDO_EN", 485 "NC", 486 "NC", 487 "NC", 488 "NC", 489 "NC", 490 "NC", 491 "NC", 492 "USB_SWITCH_SEL", 493 "NC"; 494 495 pmi8994_gpios_defaults: pmi8994-gpios-default-state { 496 vib-ldo-en-gpio-pins { 497 pins = "gpio1"; 498 function = PMIC_GPIO_FUNC_NORMAL; 499 drive-push-pull; 500 output-low; 501 bias-disable; 502 power-source = <PM8994_GPIO_S4>; 503 }; 504 505 pmi-gpio2-nc-pins { 506 pins = "gpio2"; 507 function = PMIC_GPIO_FUNC_NORMAL; 508 drive-push-pull; 509 input-enable; 510 bias-high-impedance; 511 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; 512 power-source = <PM8994_GPIO_VPH>; 513 }; 514 515 pmi-gpio3-nc-pins { 516 pins = "gpio3"; 517 function = PMIC_GPIO_FUNC_NORMAL; 518 drive-push-pull; 519 input-enable; 520 bias-high-impedance; 521 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; 522 power-source = <PM8994_GPIO_VPH>; 523 }; 524 525 pmi-gpio4-nc-pins { 526 pins = "gpio4"; 527 function = PMIC_GPIO_FUNC_NORMAL; 528 drive-push-pull; 529 output-high; 530 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; 531 power-source = <PM8994_GPIO_S4>; 532 }; 533 534 pmi-gpio5-nc-pins { 535 pins = "gpio5"; 536 function = PMIC_GPIO_FUNC_NORMAL; 537 drive-push-pull; 538 output-high; 539 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; 540 power-source = <PM8994_GPIO_S4>; 541 }; 542 543 pmi-gpio6-nc-pins { 544 pins = "gpio6"; 545 function = PMIC_GPIO_FUNC_NORMAL; 546 drive-push-pull; 547 output-high; 548 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; 549 power-source = <PM8994_GPIO_S4>; 550 }; 551 552 pmi-gpio7-nc-pins { 553 pins = "gpio7"; 554 function = PMIC_GPIO_FUNC_NORMAL; 555 drive-push-pull; 556 output-high; 557 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; 558 power-source = <PM8994_GPIO_S4>; 559 }; 560 561 pmi-gpio8-nc-pins { 562 pins = "gpio8"; 563 function = PMIC_GPIO_FUNC_NORMAL; 564 drive-push-pull; 565 output-high; 566 qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; 567 power-source = <PM8994_GPIO_S4>; 568 }; 569 570 usb-switch-sel-pins { 571 pins = "gpio9"; 572 function = PMIC_GPIO_FUNC_NORMAL; 573 drive-push-pull; 574 }; 575 576 pmi-gpio10-nc-pins { 577 pins = "gpio10"; 578 function = PMIC_GPIO_FUNC_NORMAL; 579 output-low; 580 drive-push-pull; 581 bias-disable; 582 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; 583 power-source = <PM8994_GPIO_S4>; 584 }; 585 }; 586}; 587 588&pm8994_spmi_regulators { 589 qcom,saw-reg = <&saw3>; 590 591 pm8994_s9: s9 { 592 qcom,saw-slave; 593 }; 594 595 pm8994_s10: s10 { 596 qcom,saw-slave; 597 }; 598 599 pm8994_s11: s11 { 600 qcom,saw-leader; 601 regulator-name = "vdd_apcc"; 602 regulator-always-on; 603 regulator-min-microvolt = <470000>; 604 regulator-max-microvolt = <1140000>; 605 }; 606}; 607 608&pmi8994_spmi_regulators { 609 vdd_gfx: 610 pmi8994_s2: s2 { 611 /* Pinned to a high value for now to avoid random crashes. */ 612 regulator-min-microvolt = <1015000>; 613 regulator-max-microvolt = <1015000>; 614 regulator-name = "vdd_gfx"; 615 regulator-always-on; 616 }; 617}; 618 619&pmi8994_wled { 620 default-brightness = <512>; 621 qcom,num-strings = <3>; 622 status = "okay"; 623}; 624 625&rpm_requests { 626 regulators-0 { 627 compatible = "qcom,rpm-pm8994-regulators"; 628 629 vdd_s1-supply = <&vph_pwr>; 630 vdd_s2-supply = <&vph_pwr>; 631 vdd_s3-supply = <&vph_pwr>; 632 vdd_s4-supply = <&vph_pwr>; 633 vdd_s5-supply = <&vph_pwr>; 634 vdd_s6-supply = <&vph_pwr>; 635 vdd_s7-supply = <&vph_pwr>; 636 vdd_s8-supply = <&vph_pwr>; 637 vdd_s9-supply = <&vph_pwr>; 638 vdd_s10-supply = <&vph_pwr>; 639 vdd_s11-supply = <&vph_pwr>; 640 vdd_s12-supply = <&vph_pwr>; 641 vdd_l1-supply = <&pm8994_s3>; 642 vdd_l2_l26_l28-supply = <&pm8994_s3>; 643 vdd_l3_l11-supply = <&pm8994_s3>; 644 vdd_l4_l27_l31-supply = <&pm8994_s3>; 645 vdd_l5_l7-supply = <&pm8994_s5>; 646 vdd_l6_l12_l32-supply = <&pm8994_s5>; 647 vdd_l8_l16_l30-supply = <&vph_pwr>; 648 vdd_l14_l15-supply = <&pm8994_s5>; 649 vdd_l20_l21-supply = <&pm8994_s5>; 650 vdd_l25-supply = <&pm8994_s3>; 651 vdd_lvs1_2-supply = <&pm8994_s4>; 652 653 pm8994_s3: s3 { 654 regulator-min-microvolt = <1300000>; 655 regulator-max-microvolt = <1300000>; 656 }; 657 658 pm8994_s4: s4 { 659 regulator-min-microvolt = <1800000>; 660 regulator-max-microvolt = <1800000>; 661 regulator-system-load = <325000>; 662 regulator-always-on; 663 }; 664 665 pm8994_s5: s5 { 666 regulator-min-microvolt = <2150000>; 667 regulator-max-microvolt = <2150000>; 668 }; 669 670 pm8994_s7: s7 { 671 regulator-min-microvolt = <800000>; 672 regulator-max-microvolt = <800000>; 673 }; 674 675 pm8994_l1: l1 { 676 regulator-min-microvolt = <1000000>; 677 regulator-max-microvolt = <1000000>; 678 }; 679 680 pm8994_l2: l2 { 681 regulator-min-microvolt = <1250000>; 682 regulator-max-microvolt = <1250000>; 683 }; 684 685 pm8994_l3: l3 { 686 regulator-min-microvolt = <1100000>; 687 regulator-max-microvolt = <1100000>; 688 }; 689 690 pm8994_l4: l4 { 691 regulator-min-microvolt = <1225000>; 692 regulator-max-microvolt = <1225000>; 693 }; 694 695 /* L6 and L7 seem unused. */ 696 697 pm8994_l8: l8 { 698 regulator-min-microvolt = <1800000>; 699 regulator-max-microvolt = <1800000>; 700 }; 701 702 pm8994_l9: l9 { 703 regulator-min-microvolt = <1800000>; 704 regulator-max-microvolt = <1800000>; 705 }; 706 707 pm8994_l10: l10 { 708 regulator-min-microvolt = <1800000>; 709 regulator-max-microvolt = <1800000>; 710 }; 711 712 pm8994_l11: l11 { 713 regulator-min-microvolt = <1100000>; 714 regulator-max-microvolt = <1100000>; 715 }; 716 717 pm8994_l12: l12 { 718 regulator-min-microvolt = <1800000>; 719 regulator-max-microvolt = <1800000>; 720 regulator-allow-set-load; 721 }; 722 723 pm8994_l13: l13 { 724 regulator-min-microvolt = <1800000>; 725 regulator-max-microvolt = <2950000>; 726 regulator-system-load = <22000>; 727 regulator-allow-set-load; 728 }; 729 730 pm8994_l14: l14 { 731 regulator-min-microvolt = <1700000>; 732 regulator-max-microvolt = <1900000>; 733 }; 734 735 pm8994_l15: l15 { 736 regulator-min-microvolt = <1800000>; 737 regulator-max-microvolt = <1800000>; 738 }; 739 740 pm8994_l16: l16 { 741 regulator-min-microvolt = <2700000>; 742 regulator-max-microvolt = <2700000>; 743 }; 744 745 pm8994_l17: l17 { 746 regulator-min-microvolt = <2200000>; 747 regulator-max-microvolt = <2500000>; 748 }; 749 750 pm8994_l18: l18 { 751 regulator-min-microvolt = <1800000>; 752 regulator-max-microvolt = <1800000>; 753 }; 754 755 pm8994_l19: l19 { 756 regulator-min-microvolt = <3000000>; 757 regulator-max-microvolt = <3000000>; 758 }; 759 760 pm8994_l20: l20 { 761 regulator-min-microvolt = <2950000>; 762 regulator-max-microvolt = <2950000>; 763 regulator-system-load = <570000>; 764 regulator-allow-set-load; 765 }; 766 767 pm8994_l21: l21 { 768 regulator-min-microvolt = <2950000>; 769 regulator-max-microvolt = <2950000>; 770 regulator-system-load = <800000>; 771 regulator-allow-set-load; 772 }; 773 774 pm8994_l22: l22 { 775 regulator-min-microvolt = <3000000>; 776 regulator-max-microvolt = <3000000>; 777 }; 778 779 pm8994_l23: l23 { 780 regulator-min-microvolt = <2700000>; 781 regulator-max-microvolt = <2700000>; 782 }; 783 784 pm8994_l24: l24 { 785 regulator-min-microvolt = <3075000>; 786 regulator-max-microvolt = <3075000>; 787 regulator-allow-set-load; 788 }; 789 790 pm8994_l25: l25 { 791 regulator-min-microvolt = <1200000>; 792 regulator-max-microvolt = <1200000>; 793 regulator-allow-set-load; 794 }; 795 796 pm8994_l27: l27 { 797 regulator-min-microvolt = <1000000>; 798 regulator-max-microvolt = <1200000>; 799 }; 800 801 pm8994_l28: l28 { 802 regulator-min-microvolt = <925000>; 803 regulator-max-microvolt = <925000>; 804 regulator-allow-set-load; 805 }; 806 807 pm8994_l29: l29 { 808 regulator-min-microvolt = <2700000>; 809 regulator-max-microvolt = <2700000>; 810 }; 811 812 pm8994_l30: l30 { }; 813 814 pm8994_l32: l32 { 815 regulator-min-microvolt = <1800000>; 816 regulator-max-microvolt = <1800000>; 817 }; 818 }; 819}; 820 821&sdhc1 { 822 vmmc-supply = <&pm8994_l20>; 823 vqmmc-supply = <&pm8994_s4>; 824 mmc-hs400-1_8v; 825 mmc-hs200-1_8v; 826 status = "okay"; 827}; 828 829&sdhc2 { 830 cd-gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>; 831 vmmc-supply = <&pm8994_l21>; 832 vqmmc-supply = <&pm8994_l13>; 833 status = "okay"; 834}; 835 836&tlmm { 837 gpio-reserved-ranges = <0 4>; 838 pinctrl-0 = <&sw_service_gpio>; 839 pinctrl-names = "default"; 840 841 disp_reset_n_gpio: disp-reset-n-state { 842 pins = "gpio8"; 843 function = "gpio"; 844 drive-strength = <2>; 845 bias-disable; 846 }; 847 848 mdp_vsync_p_gpio: mdp-vsync-p-state { 849 pins = "gpio10"; 850 function = "mdp_vsync"; 851 drive-strength = <2>; 852 bias-disable; 853 }; 854 855 sw_service_gpio: sw-service-gpio-state { 856 pins = "gpio16"; 857 function = "gpio"; 858 drive-strength = <2>; 859 bias-pull-up; 860 }; 861 862 usb_detect: usb-detect-state { 863 pins = "gpio25"; 864 function = "gpio"; 865 drive-strength = <2>; 866 bias-disable; 867 output-high; 868 }; 869 870 uim_detect_en: uim-detect-en-state { 871 pins = "gpio29"; 872 function = "gpio"; 873 drive-strength = <2>; 874 bias-disable; 875 output-high; 876 }; 877 878 tray_det_pin: tray-det-state { 879 pins = "gpio40"; 880 function = "gpio"; 881 drive-strength = <2>; 882 bias-disable; 883 }; 884 885 tp_vddio_en: tp-vddio-en-state { 886 pins = "gpio50"; 887 function = "gpio"; 888 drive-strength = <2>; 889 bias-disable; 890 output-high; 891 }; 892 893 lcd_vddio_en: lcd-vddio-en-state { 894 pins = "gpio51"; 895 function = "gpio"; 896 drive-strength = <2>; 897 bias-disable; 898 output-low; 899 }; 900 901 wl_host_wake: wl-host-wake-state { 902 pins = "gpio79"; 903 function = "gpio"; 904 drive-strength = <2>; 905 bias-pull-down; 906 }; 907 908 wl_reg_on: wl-reg-on-state { 909 pins = "gpio84"; 910 function = "gpio"; 911 drive-strength = <2>; 912 bias-disable; 913 output-low; 914 }; 915 916 ts_reset_n: ts-rst-n-state { 917 pins = "gpio89"; 918 function = "gpio"; 919 drive-strength = <2>; 920 }; 921 922 touch_int_n: touch-int-n-state { 923 pins = "gpio125"; 924 function = "gpio"; 925 drive-strength = <2>; 926 bias-pull-up; 927 }; 928 929 touch_int_sleep: touch-int-sleep-state { 930 pins = "gpio125"; 931 function = "gpio"; 932 drive-strength = <2>; 933 bias-pull-down; 934 }; 935}; 936 937&usb3 { 938 qcom,select-utmi-as-pipe-clk; 939 status = "okay"; 940}; 941 942&usb3_dwc3 { 943 extcon = <&usb3_id>; 944 dr_mode = "peripheral"; 945 maximum-speed = "high-speed"; 946 phys = <&hsusb_phy1>; 947 phy-names = "usb2-phy"; 948 snps,hird-threshold = /bits/ 8 <0>; 949}; 950