1// SPDX-License-Identifier: GPL-2.0+ 2/* 3 * Copyright (C) 2020 Marvell International Ltd. 4 */ 5 6#include "cn9130.dtsi" /* include SoC device tree */ 7 8#include <dt-bindings/gpio/gpio.h> 9 10/ { 11 chosen { 12 stdout-path = "serial0:115200n8"; 13 }; 14 15 aliases { 16 i2c0 = &cp0_i2c0; 17 ethernet0 = &cp0_eth0; 18 ethernet1 = &cp0_eth1; 19 ethernet2 = &cp0_eth2; 20 gpio1 = &cp0_gpio1; 21 gpio2 = &cp0_gpio2; 22 }; 23 24 memory@0 { 25 device_type = "memory"; 26 reg = <0x0 0x0 0x0 0x80000000>; 27 }; 28 29 ap0_reg_mmc_vccq: ap0_mmc_vccq@0 { 30 compatible = "regulator-gpio"; 31 regulator-name = "ap0_mmc_vccq"; 32 regulator-min-microvolt = <1800000>; 33 regulator-max-microvolt = <3300000>; 34 gpios = <&expander0 5 GPIO_ACTIVE_HIGH>; 35 states = <1800000 0x1 36 3300000 0x0>; 37 }; 38 39 cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 { 40 compatible = "regulator-fixed"; 41 regulator-name = "cp0-xhci1-vbus"; 42 regulator-min-microvolt = <5000000>; 43 regulator-max-microvolt = <5000000>; 44 enable-active-high; 45 gpio = <&expander0 8 GPIO_ACTIVE_HIGH>; 46 }; 47 48 cp0_usb3_0_phy0: cp0_usb3_phy0 { 49 compatible = "usb-nop-xceiv"; 50 }; 51 52 cp0_usb3_0_phy1: cp0_usb3_phy1 { 53 compatible = "usb-nop-xceiv"; 54 vcc-supply = <&cp0_reg_usb3_vbus1>; 55 }; 56 57 cp0_reg_sd_vccq: cp0_sd_vccq@0 { 58 compatible = "regulator-gpio"; 59 regulator-name = "cp0_sd_vccq"; 60 regulator-min-microvolt = <1800000>; 61 regulator-max-microvolt = <3300000>; 62 gpios = <&cp0_gpio2 18 GPIO_ACTIVE_HIGH>; 63 states = <1800000 0x1 64 3300000 0x0>; 65 }; 66 67 cp0_reg_sd_vcc: cp0_sd_vcc@0 { 68 compatible = "regulator-fixed"; 69 regulator-name = "cp0_sd_vcc"; 70 regulator-min-microvolt = <3300000>; 71 regulator-max-microvolt = <3300000>; 72 gpio = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>; 73 enable-active-high; 74 regulator-always-on; 75 }; 76 77 sfp: sfp { 78 compatible = "sff,sfp"; 79 i2c-bus = <&cp0_i2c1>; 80 mod-def0-gpios = <&expander0 3 GPIO_ACTIVE_LOW>; 81 los-gpio = <&expander0 15 GPIO_ACTIVE_HIGH>; 82 tx-disable-gpio = <&expander0 2 GPIO_ACTIVE_HIGH>; 83 tx-fault-gpio = <&cp0_gpio1 24 GPIO_ACTIVE_HIGH>; 84 maximum-power-milliwatt = <3000>; 85 status = "okay"; 86 }; 87}; 88 89&uart0 { 90 status = "okay"; 91}; 92 93/* on-board eMMC U6 */ 94&ap_sdhci0 { 95 pinctrl-names = "default"; 96 bus-width = <8>; 97 status = "okay"; 98 mmc-ddr-1_8v; 99 vqmmc-supply = <&ap0_reg_mmc_vccq>; 100}; 101 102&cp0_syscon0 { 103 cp0_pinctrl: pinctrl { 104 compatible = "marvell,cp115-standalone-pinctrl"; 105 106 cp0_i2c0_pins: cp0-i2c-pins-0 { 107 marvell,pins = "mpp37", "mpp38"; 108 marvell,function = "i2c0"; 109 }; 110 cp0_i2c1_pins: cp0-i2c-pins-1 { 111 marvell,pins = "mpp35", "mpp36"; 112 marvell,function = "i2c1"; 113 }; 114 cp0_sdhci_cd_pins_crb: cp0-sdhci-cd-pins-crb { 115 marvell,pins = "mpp55"; 116 marvell,function = "gpio"; 117 }; 118 cp0_sdhci_pins: cp0-sdhi-pins-0 { 119 marvell,pins = "mpp56", "mpp57", "mpp58", 120 "mpp59", "mpp60", "mpp61"; 121 marvell,function = "sdio"; 122 }; 123 cp0_spi0_pins: cp0-spi-pins-0 { 124 marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16"; 125 marvell,function = "spi1"; 126 }; 127 }; 128}; 129 130&cp0_gpio1 { 131 status = "okay"; 132}; 133 134&cp0_gpio2 { 135 status = "okay"; 136}; 137 138&cp0_i2c0 { 139 pinctrl-names = "default"; 140 pinctrl-0 = <&cp0_i2c0_pins>; 141 status = "okay"; 142 clock-frequency = <100000>; 143 expander0: mcp23x17@20 { 144 compatible = "microchip,mcp23017"; 145 gpio-controller; 146 #gpio-cells = <2>; 147 reg = <0x20>; 148 status = "okay"; 149 }; 150}; 151 152&cp0_i2c1 { 153 pinctrl-names = "default"; 154 pinctrl-0 = <&cp0_i2c1_pins>; 155 clock-frequency = <100000>; 156 status = "okay"; 157}; 158 159 160&cp0_sdhci0 { 161 pinctrl-names = "default"; 162 pinctrl-0 = <&cp0_sdhci_pins 163 &cp0_sdhci_cd_pins_crb>; 164 bus-width = <4>; 165 cd-gpios = <&cp0_gpio2 23 GPIO_ACTIVE_HIGH>; 166 vqmmc-supply = <&cp0_reg_sd_vccq>; 167 vmmc-supply = <&cp0_reg_sd_vcc>; 168 status = "okay"; 169}; 170 171&cp0_spi1 { 172 pinctrl-names = "default"; 173 pinctrl-0 = <&cp0_spi0_pins>; 174 reg = <0x700680 0x50>, /* control */ 175 <0x2000000 0x1000000>; /* CS0 */ 176 status = "okay"; 177 178 flash@0 { 179 #address-cells = <0x1>; 180 #size-cells = <0x1>; 181 compatible = "jedec,spi-nor"; 182 reg = <0x0>; 183 /* On-board MUX does not allow higher frequencies */ 184 spi-max-frequency = <40000000>; 185 186 partitions { 187 compatible = "fixed-partitions"; 188 #address-cells = <1>; 189 #size-cells = <1>; 190 191 partition@0 { 192 label = "U-Boot"; 193 reg = <0x0 0x200000>; 194 }; 195 196 partition@400000 { 197 label = "Filesystem"; 198 reg = <0x200000 0xe00000>; 199 }; 200 }; 201 }; 202}; 203 204&cp0_mdio { 205 status = "okay"; 206 phy0: ethernet-phy@0 { 207 reg = <0>; 208 }; 209 210 switch6: switch0@6 { 211 /* Actual device is MV88E6393X */ 212 compatible = "marvell,mv88e6190"; 213 #address-cells = <1>; 214 #size-cells = <0>; 215 reg = <6>; 216 interrupt-parent = <&cp0_gpio1>; 217 interrupts = <28 IRQ_TYPE_LEVEL_LOW>; 218 interrupt-controller; 219 #interrupt-cells = <2>; 220 221 dsa,member = <0 0>; 222 223 ports { 224 #address-cells = <1>; 225 #size-cells = <0>; 226 227 port@1 { 228 reg = <1>; 229 label = "p1"; 230 phy-handle = <&switch0phy1>; 231 }; 232 233 port@2 { 234 reg = <2>; 235 label = "p2"; 236 phy-handle = <&switch0phy2>; 237 }; 238 239 port@3 { 240 reg = <3>; 241 label = "p3"; 242 phy-handle = <&switch0phy3>; 243 }; 244 245 port@4 { 246 reg = <4>; 247 label = "p4"; 248 phy-handle = <&switch0phy4>; 249 }; 250 251 port@5 { 252 reg = <5>; 253 label = "p5"; 254 phy-handle = <&switch0phy5>; 255 }; 256 257 port@6 { 258 reg = <6>; 259 label = "p6"; 260 phy-handle = <&switch0phy6>; 261 }; 262 263 port@7 { 264 reg = <7>; 265 label = "p7"; 266 phy-handle = <&switch0phy7>; 267 }; 268 269 port@8 { 270 reg = <8>; 271 label = "p8"; 272 phy-handle = <&switch0phy8>; 273 }; 274 275 port@9 { 276 reg = <9>; 277 label = "p9"; 278 phy-mode = "10gbase-r"; 279 sfp = <&sfp>; 280 managed = "in-band-status"; 281 }; 282 283 port@a { 284 reg = <10>; 285 label = "cpu"; 286 ethernet = <&cp0_eth0>; 287 }; 288 289 }; 290 291 mdio { 292 #address-cells = <1>; 293 #size-cells = <0>; 294 295 switch0phy1: switch0phy1@1 { 296 reg = <0x1>; 297 }; 298 299 switch0phy2: switch0phy2@2 { 300 reg = <0x2>; 301 }; 302 303 switch0phy3: switch0phy3@3 { 304 reg = <0x3>; 305 }; 306 307 switch0phy4: switch0phy4@4 { 308 reg = <0x4>; 309 }; 310 311 switch0phy5: switch0phy5@5 { 312 reg = <0x5>; 313 }; 314 315 switch0phy6: switch0phy6@6 { 316 reg = <0x6>; 317 }; 318 319 switch0phy7: switch0phy7@7 { 320 reg = <0x7>; 321 }; 322 323 switch0phy8: switch0phy8@8 { 324 reg = <0x8>; 325 }; 326 }; 327 }; 328}; 329 330&cp0_xmdio { 331 status = "okay"; 332 nbaset_phy0: ethernet-phy@0 { 333 compatible = "ethernet-phy-ieee802.3-c45"; 334 reg = <0>; 335 }; 336}; 337 338&cp0_ethernet { 339 status = "okay"; 340}; 341 342&cp0_eth0 { 343 /* This port is connected to 88E6393X switch */ 344 status = "okay"; 345 phy-mode = "10gbase-r"; 346 managed = "in-band-status"; 347 phys = <&cp0_comphy4 0>; 348}; 349 350&cp0_eth1 { 351 status = "okay"; 352 phy = <&phy0>; 353 phy-mode = "rgmii-id"; 354}; 355 356&cp0_eth2 { 357 /* This port uses "2500base-t" phy-mode */ 358 status = "disabled"; 359 phy = <&nbaset_phy0>; 360 phys = <&cp0_comphy5 2>; 361}; 362 363