1// SPDX-License-Identifier: GPL-2.0 2/* 3 * dts file for Hisilicon HiKey970 Development Board 4 * 5 * Copyright (C) 2016, HiSilicon Ltd. 6 * Copyright (C) 2018, Linaro Ltd. 7 * 8 */ 9 10/dts-v1/; 11#include <dt-bindings/gpio/gpio.h> 12 13#include "hi3670.dtsi" 14#include "hikey970-pinctrl.dtsi" 15#include "hikey970-pmic.dtsi" 16 17/ { 18 model = "HiKey970"; 19 compatible = "hisilicon,hi3670-hikey970", "hisilicon,hi3670"; 20 21 aliases { 22 mshc1 = &dwmmc1; 23 mshc2 = &dwmmc2; 24 serial0 = &uart0; 25 serial1 = &uart1; 26 serial2 = &uart2; 27 serial3 = &uart3; 28 serial4 = &uart4; 29 serial5 = &uart5; 30 serial6 = &uart6; /* console UART */ 31 }; 32 33 chosen { 34 stdout-path = "serial6:115200n8"; 35 }; 36 37 memory@0 { 38 device_type = "memory"; 39 /* expect bootloader to fill in this region */ 40 reg = <0x0 0x0 0x0 0x0>; 41 }; 42 43 wlan_en: wlan-en-1-8v { 44 compatible = "regulator-fixed"; 45 regulator-name = "wlan-en-regulator"; 46 regulator-min-microvolt = <1800000>; 47 regulator-max-microvolt = <1800000>; 48 49 /* GPIO_051_WIFI_EN */ 50 gpio = <&gpio6 3 0>; 51 52 /* WLAN card specific delay */ 53 startup-delay-us = <70000>; 54 enable-active-high; 55 }; 56}; 57 58/* 59 * Legend: proper name = the GPIO line is used as GPIO 60 * NC = not connected (pin out but not routed from the chip to 61 * anything the board) 62 * "[PER]" = pin is muxed for [peripheral] (not GPIO) 63 * "" = no idea, schematic doesn't say, could be 64 * unrouted (not connected to any external pin) 65 * LSEC = Low Speed External Connector 66 * HSEC = High Speed External Connector 67 * 68 * Line names are taken from "hikey970-schematics.pdf" from HiSilicon. 69 * 70 * For the lines routed to the external connectors the 71 * lines are named after the 96Boards CE Specification 1.0, 72 * Appendix "Expansion Connector Signal Description". 73 * 74 * When the 96Board naming of a line and the schematic name of 75 * the same line are in conflict, the 96Board specification 76 * takes precedence, which means that the external UART on the 77 * LSEC is named UART0 while the schematic and SoC names this 78 * UART2. This is only for the informational lines i.e. "[FOO]", 79 * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only 80 * ones actually used for GPIO. 81 */ 82&gpio0 { 83 /* GPIO_000-GPIO_007 */ 84 gpio-line-names = 85 "", 86 "TP901", /* TEST_MODE connected to TP901 */ 87 "", 88 "GPIO_003_USB_HUB_RESET_N", 89 "NC", 90 "[AP_GPS_REF_CLK]", 91 "[I2C3_SCL]", 92 "[I2C3_SDA]"; 93}; 94 95&gpio1 { 96 /* GPIO_008-GPIO_015 */ 97 gpio-line-names = 98 "[UART0_CTS]", /* LSEC pin 3: GPIO_008_UART2_CTS_N */ 99 "[UART0_RTS]", /* LSEC pin 9: GPIO_009_UART2_RTS_N */ 100 "[UART0_TXD]", /* LSEC pin 5: GPIO_010_UART2_TXD */ 101 "[UART0_RXD]", /* LSEC pin 7: GPIO_011_UART2_RXD */ 102 "[USER_LED5]", 103 "GPIO-I", /* LSEC pin 31: GPIO_013_CAM0_RST_N */ 104 "[USER_LED3]", 105 "[USER_LED4]"; 106}; 107 108&gpio2 { 109 /* GPIO_016-GPIO_023 */ 110 gpio-line-names = 111 "GPIO-G", /* LSEC pin 29: GPIO_016_LCD_TE0 */ 112 "[CSI0_MCLK]", /* HSEC pin 15: ISP_CCLK0_MCAM */ 113 "[CSI1_MCLK]", /* HSEC pin 17: ISP_CCLK1_SCAM */ 114 "GPIO_019_BT_ACTIVE", 115 "[I2C2_SCL]", /* HSEC pin 32: ISP_SCL0 */ 116 "[I2C2_SDA]", /* HSEC pin 34: ISP_SDA0 */ 117 "[I2C3_SCL]", /* HSEC pin 36: ISP_SCL1 */ 118 "[I2C3_SDA]"; /* HSEC pin 38: ISP_SDA1 */ 119}; 120 121&gpio3 { 122 /* GPIO_024-GPIO_031 */ 123 gpio-line-names = 124 "GPIO_024_WIFI_ACTIVE", 125 "GPIO_025_PERST_M.2", 126 "[I2C4_SCL]", 127 "[I2C4_SDA]", 128 "NC", 129 "GPIO-H", /* LSEC pin 30: GPIO_029_LCD_RST_N */ 130 "[USER_LED1]", 131 "GPIO-L"; /* LSEC pin 34: GPIO_031 */ 132}; 133 134&gpio4 { 135 /* GPIO_032-GPIO_039 */ 136 gpio-line-names = 137 "GPIO-K", /* LSEC pin 33: GPIO_032_CAM1_RST_N */ 138 "GPIO_033_PMU1_EN", 139 "GPIO_034_USBSW_SEL", 140 /* 141 * These two pins should be used for SD(IO) data according 142 * to the 96boards specification but seems to be repurposed 143 * for UART 0. They are however named according to the spec. 144 */ 145 "[SD_DAT1]", /* HSEC pin 3: GPIO_035_UART0_RXD */ 146 "[SD_DAT2]", /* HSEC pin 5: GPIO_036_UART0_TXD */ 147 "[UART1_RXD]", /* LSEC pin 13: DEBUG_UART6_RXD */ 148 "[UART1_TXD]", /* LSEC pin 11: DEBUG_UART6_TXD */ 149 "[SOC_GPS_UART3_CTS_N]"; /* TP2304 */ 150}; 151 152&gpio5 { 153 /* GPIO_040-GPIO_047 */ 154 gpio-line-names = 155 "[SOC_GPS_UART3_RTS_N]", /* TP2302 */ 156 "[SOC_GPS_UART3_RXD]", /* TP2303 */ 157 "[SOC_GPS_UART3_TXD]", /* TP2305 */ 158 "[SOC_BT_UART4_CTS_N]", 159 "[SOC_BT_UART4_RTS_N]", 160 "[SOC_BT_UART4_RXD]", 161 "[SOC_BT_UART4_TXD]", 162 "NC"; 163}; 164 165&gpio6 { 166 /* GPIO_048-GPIO_055 */ 167 gpio-line-names = 168 "NC", 169 "GPIO_049_USER_LED6", 170 "GPIO_050_CAN_RST", 171 "GPIO_051_WIFI_EN", 172 "GPIO-D", /* LSEC pin 26 */ 173 "GPIO-J", /* LSEC pin 32 */ 174 "GPIO_054_BT_EN", 175 "[GPIO_055_SEL]"; 176}; 177 178&gpio7 { 179 /* GPIO_056-GPIO_063 */ 180 gpio-line-names = 181 "[PCIE_PERST_L]", "NC", "NC", "NC", "NC", "NC", "NC", "NC"; 182}; 183 184&gpio8 { 185 /* GPIO_064-GPIO_071 */ 186 gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC"; 187}; 188 189&gpio9 { 190 /* GPIO_072-GPIO_079 */ 191 gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC"; 192}; 193 194&gpio10 { 195 /* GPIO_080-GPIO_087 */ 196 gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC"; 197}; 198 199&gpio11 { 200 /* GPIO_088-GPIO_095 */ 201 gpio-line-names = "NC", "NC", "NC", "NC", "NC", "NC", "NC", "NC"; 202}; 203 204&gpio12 { 205 /* GPIO_096-GPIO_103 */ 206 gpio-line-names = "NC", "", "", "", "", "", "", ""; 207}; 208 209&gpio13 { 210 /* GPIO_104-GPIO_111 */ 211 gpio-line-names = "", "", "", "", "", "", "", ""; 212}; 213 214&gpio14 { 215 /* GPIO_112-GPIO_119 */ 216 gpio-line-names = "", "", "", "", "", "", "", ""; 217}; 218 219&gpio15 { 220 /* GPIO_120-GPIO_127 */ 221 gpio-line-names = "", "", "", "", "", "", "", ""; 222}; 223 224&gpio16 { 225 /* GPIO_128-GPIO_135 */ 226 gpio-line-names = 227 "[WL_SDIO_CLK]", 228 "[WL_SDIO_CMD]", 229 "[WL_SDIO_DATA0]", 230 "[WL_SDIO_DATA1]", 231 "[WL_SDIO_DATA2]", 232 "[WL_SDIO_DATA3]", 233 "[ETH_ISOLATE]", 234 "NC"; 235}; 236 237&gpio17 { 238 /* GPIO_136-GPIO_143 */ 239 gpio-line-names = 240 "[MINI1CLK_EN]", "NC", "", "", "", "", "", ""; 241}; 242 243&gpio18 { 244 /* GPIO_144-GPIO_151 */ 245 gpio-line-names = 246 "[SPI1_SCLK]", /* HSEC pin 9: GPIO_144_SPI3_CLK */ 247 "[SPI1_DIN]", /* HSEC pin 11: GPIO_145_SPI3_DI */ 248 "[SPI1_DOUT]", /* HSEC pin 1: GPIO_146_SPI3_DO */ 249 "[SPI1_CS]", /* HSEC pin 7: GPIO_147_SPI3_CS0_N */ 250 "[POWER_INT_N]", 251 "[CDMA_GPS_SYNC]", 252 "GPIO_150_PEX_INTA", 253 "GPIO_151_CAN_INT"; 254}; 255 256&gpio19 { 257 /* GPIO_152-GPIO_159 */ 258 gpio-line-names = "", "", "", "", "", "", "", ""; 259}; 260 261&gpio20 { 262 /* GPIO_160-GPIO_167 */ 263 gpio-line-names = 264 "[SD_CLK]", 265 "[SD_CMD]", 266 "[SD_DATA0]", 267 "[SD_DATA1]", 268 "[SD_DATA2]", 269 "[SD_DATA3]", 270 "GPIO_166_ETHCLK_EN", 271 "GPIO_167_USER_LED2"; 272}; 273 274&gpio21 { 275 /* GPIO_168-GPIO_175 */ 276 gpio-line-names = 277 "GPIO_168_GPS_EN", 278 "GPIO-C", /* LSEC pin 25: GPIO_169_USIM1_CLK */ 279 "GPIO-E", /* LSEC pin 27: GPIO_170_USIM1_RST */ 280 "GPIO-B", /* LSEC pin 24: GPIO_171_USIM1_DATA */ 281 "", "", "", "", ""; 282}; 283 284&gpio22 { 285 /* GPIO_176-GPIO_183 */ 286 gpio-line-names = 287 "[PMU_PWR_HOLD]", 288 "GPIO_177_WL_WAKEUP_AP", 289 "[JTAG_TCK]", 290 "[JTAG_TMS]", 291 "[JTAG_TDI]", 292 "[JTAG_TMS]", 293 "GPIO_182_FATAL_ERR", 294 "NC"; 295}; 296 297&gpio23 { 298 /* GPIO_184-GPIO_191 */ 299 gpio-line-names = 300 "GPIO_184_JTAG_SEL", 301 "GPIO-F", /* LSEC pin 28: GPIO_185_LCD_BL_PWM */ 302 "[I2C0_SCL]", /* LSEC pin 15: GPIO_186_I2C0_SCL */ 303 "[I2C0_SDA]", /* LSEC pin 17: GPIO_187_I2C0_SDA */ 304 "[GPIO_188_I2C1_SCL]", /* Actual SoC I2C1_SCL */ 305 "[GPIO_189_I2C1_SDA]", /* Actual SoC I2C1_SDA */ 306 "[I2C1_SCL]", /* LSEC pin 19: GPIO_190_I2C2_SCL */ 307 "[I2C2_SDA]"; /* LSEC pin 21: GPIO_191_I2C2_SDA */ 308}; 309 310&gpio24 { 311 /* GPIO_192-GPIO_199 */ 312 gpio-line-names = 313 "[SD_LED]", 314 "NC", 315 "[PCM_DI]", /* LSEC pin 22: GPIO_194_I2S0_DI */ 316 "[PCM_DO]", /* LSEC pin 20: GPIO_195_I2S0_DO */ 317 "[PCM_CLK]", /* LSEC pin 18: GPIO_196_I2S0_XCLK */ 318 "[PCM_FS]", /* LSEC pin 16: GPIO_197_I2S0_XFS */ 319 "", 320 "[I2S2_DO]"; 321}; 322 323&gpio25 { 324 /* GPIO_200-GPIO_207 */ 325 gpio-line-names = 326 "[I2S2_XCLK]", 327 "[I2S2_XFS]", 328 "GPIO_202_PERST_ETH", 329 "GPIO_203_PWRON_DET", 330 "GPIO_204_PMU1_IRQ_N", 331 "GPIO_205_SD_DET", 332 "GPIO_206_GPS_MOTION_INT", 333 "GPIO_207_HDMI_SEL"; 334}; 335 336&gpio26 { 337 /* GPIO_208-GPIO_215 */ 338 gpio-line-names = 339 "GPIO-A", /* LSEC pin 23: GPIO_208_WAKEUP_SOC */ 340 "GPIO_209_VBUS_TYPEC", 341 "NC", 342 "NC", 343 "NC", 344 "[SPI0_SCLK]", /* LSEC pin 8: GPIO_213_SPI2_CLK */ 345 "[SPI0_DIN]", /* LSEC pin 10: GPIO_214_SPI2_DI */ 346 "[SPI0_DOUT]"; /* LSEC pin 14: GPIO_215_SPI2_DO */ 347}; 348 349&gpio27 { 350 /* GPIO_216-GPIO_223 */ 351 gpio-line-names = 352 "[SPI0_CS]", /* LSEC pin 12: GPIO_216_SPI2_CS0_N */ 353 "GPIO_217_HDMI_PD", 354 "GPIO_218_GPS_WAKEUP_AP", 355 "GPIO_219_M.2CLK_EN", 356 "GPIO_220_PERST_MINI", 357 "GPIO_221_CC_INT", 358 "[PCIE_CLKREQ_L]", 359 "NC"; 360}; 361 362&gpio28 { 363 /* GPIO_224-GPIO_231 */ 364 gpio-line-names = 365 "[PMU0_INT]", 366 "[SPMI_DATA]", 367 "[SPMI_CLK]", 368 "[CAN_SPI_CLK]", 369 "[CAN_SPI_DI]", 370 "[CAN_SPI_DO]", 371 "[CAN_SPI_CS]", 372 "GPIO_231_HDMI_INT"; 373}; 374 375&dwmmc1 { 376 bus-width = <0x4>; 377 sd-uhs-sdr12; 378 sd-uhs-sdr25; 379 sd-uhs-sdr50; 380 sd-uhs-sdr104; 381 cap-sd-highspeed; 382 disable-wp; 383 cd-inverted; 384 cd-gpios = <&gpio25 5 GPIO_ACTIVE_HIGH>; 385 pinctrl-names = "default"; 386 pinctrl-0 = <&sd_pmx_func 387 &sd_clk_cfg_func 388 &sd_cfg_func>; 389 vmmc-supply = <&ldo16>; 390 vqmmc-supply = <&ldo9>; 391 status = "okay"; 392}; 393 394&dwmmc2 { /* WIFI */ 395 bus-width = <0x4>; 396 non-removable; 397 broken-cd; 398 cap-power-off-card; 399 pinctrl-names = "default"; 400 pinctrl-0 = <&sdio_pmx_func 401 &sdio_clk_cfg_func 402 &sdio_cfg_func>; 403 /* WL_EN */ 404 vmmc-supply = <&wlan_en>; 405 status = "okay"; 406 407 wlcore: wlcore@2 { 408 compatible = "ti,wl1837"; 409 reg = <2>; /* sdio func num */ 410 /* WL_IRQ, GPIO_177_WL_WAKEUP_AP */ 411 interrupt-parent = <&gpio22>; 412 interrupts = <1 IRQ_TYPE_EDGE_RISING>; 413 }; 414}; 415 416&uart0 { 417 /* On High speed expansion header */ 418 label = "HS-UART0"; 419 status = "okay"; 420}; 421 422&uart2 { 423 /* On Low speed expansion header */ 424 label = "LS-UART0"; 425 status = "okay"; 426}; 427 428&uart6 { 429 /* On Low speed expansion header */ 430 label = "LS-UART1"; 431 status = "okay"; 432}; 433