1// SPDX-License-Identifier: (GPL-2.0+ OR MIT) 2// Copyright (C) 2016 ARM Ltd. 3// Copyright (C) 2018 Hauke Mehrtens <hauke@hauke-m.de> 4 5/dts-v1/; 6#include "sun50i-h5.dtsi" 7 8#include <dt-bindings/gpio/gpio.h> 9#include <dt-bindings/input/input.h> 10#include <dt-bindings/pinctrl/sun4i-a10.h> 11 12/ { 13 model = "Xunlong Orange Pi Zero Plus"; 14 compatible = "xunlong,orangepi-zero-plus", "allwinner,sun50i-h5"; 15 16 reg_vcc3v3: vcc3v3 { 17 compatible = "regulator-fixed"; 18 regulator-name = "vcc3v3"; 19 regulator-min-microvolt = <3300000>; 20 regulator-max-microvolt = <3300000>; 21 }; 22 23 aliases { 24 ethernet0 = &emac; 25 ethernet1 = &rtl8189ftv; 26 serial0 = &uart0; 27 }; 28 29 chosen { 30 stdout-path = "serial0:115200n8"; 31 }; 32 33 leds { 34 compatible = "gpio-leds"; 35 36 led-0 { 37 label = "orangepi:green:pwr"; 38 gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */ 39 default-state = "on"; 40 }; 41 42 led-1 { 43 label = "orangepi:red:status"; 44 gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */ 45 }; 46 }; 47 48 reg_gmac_3v3: gmac-3v3 { 49 compatible = "regulator-fixed"; 50 regulator-name = "gmac-3v3"; 51 regulator-min-microvolt = <3300000>; 52 regulator-max-microvolt = <3300000>; 53 startup-delay-us = <100000>; 54 enable-active-high; 55 gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */ 56 }; 57}; 58 59&ehci0 { 60 status = "okay"; 61}; 62 63&ehci1 { 64 status = "okay"; 65}; 66 67&emac { 68 pinctrl-names = "default"; 69 pinctrl-0 = <&emac_rgmii_pins>; 70 phy-supply = <®_gmac_3v3>; 71 phy-handle = <&ext_rgmii_phy>; 72 phy-mode = "rgmii"; 73 status = "okay"; 74}; 75 76&external_mdio { 77 ext_rgmii_phy: ethernet-phy@1 { 78 compatible = "ethernet-phy-ieee802.3-c22"; 79 reg = <1>; 80 }; 81}; 82 83&mmc0 { 84 vmmc-supply = <®_vcc3v3>; 85 bus-width = <4>; 86 cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ 87 status = "okay"; 88}; 89 90&mmc1 { 91 vmmc-supply = <®_vcc3v3>; 92 bus-width = <4>; 93 non-removable; 94 status = "okay"; 95 96 /* 97 * Explicitly define the sdio device, so that we can add an ethernet 98 * alias for it (which e.g. makes u-boot set a mac-address). 99 */ 100 rtl8189ftv: sdio_wifi@1 { 101 reg = <1>; 102 }; 103}; 104 105&spi0 { 106 status = "okay"; 107 108 flash@0 { 109 #address-cells = <1>; 110 #size-cells = <1>; 111 compatible = "mxicy,mx25l1606e", "winbond,w25q128"; 112 reg = <0>; 113 spi-max-frequency = <40000000>; 114 }; 115}; 116 117&ohci0 { 118 status = "okay"; 119}; 120 121&ohci1 { 122 status = "okay"; 123}; 124 125&uart0 { 126 pinctrl-names = "default"; 127 pinctrl-0 = <&uart0_pa_pins>; 128 status = "okay"; 129}; 130 131&usb_otg { 132 dr_mode = "peripheral"; 133 status = "okay"; 134}; 135 136&usbphy { 137 /* USB Type-A ports' VBUS is always on */ 138 usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ 139 status = "okay"; 140}; 141