xref: /freebsd/sys/contrib/device-tree/src/arm/ti/omap/am335x-moxa-uc-2101.dts (revision e9ac41698b2f322d55ccf9da50a3596edb2c1800)
1// SPDX-License-Identifier: GPL-2.0
2/*
3 * Copyright (C) 2018 MOXA Inc. - https://www.moxa.com/
4 *
5 * Authors: SZ Lin (林上智) <sz.lin@moxa.com>
6 *          Wes Huang (黃淵河) <wes.huang@moxa.com>
7 *          Fero JD Zhou (周俊達) <FeroJD.Zhou@moxa.com>
8 */
9
10/dts-v1/;
11
12#include "am335x-moxa-uc-2100-common.dtsi"
13
14/ {
15	model = "Moxa UC-2101";
16	compatible = "moxa,uc-2101", "ti,am33xx";
17
18	leds {
19		compatible = "gpio-leds";
20		led1 {
21			label = "UC2100:GREEN:USER";
22			gpios = <&gpio3 10 GPIO_ACTIVE_HIGH>;
23			default-state = "off";
24		};
25	};
26};
27
28&am33xx_pinmux {
29	pinctrl-names = "default";
30
31	cpsw_default: cpsw-default-pins {
32		pinctrl-single,pins = <
33			/* Slave 1 */
34			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE1)	/* mii1_crs.rmii1_crs_dv */
35			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLUP, MUX_MODE1)	/* mii1_rxerr.rmii1_rxerr */
36			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE1)	/* mii1_txen.rmii1_txen */
37			AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_OUTPUT_PULLDOWN, MUX_MODE1)	/* mii1_txd1.rmii1_txd1 */
38			AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_OUTPUT_PULLDOWN, MUX_MODE1)	/* mii1_txd0.rmii1_txd0 */
39			AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLUP, MUX_MODE1)	/* mii1_rxd1.rmii1_rxd1 */
40			AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLUP, MUX_MODE1)	/* mii1_rxd0.rmii1_rxd0 */
41			AM33XX_PADCONF(AM335X_PIN_RMII1_REF_CLK, PIN_INPUT_PULLDOWN, MUX_MODE0)
42		>;
43	};
44
45	spi1_pins: spi1-pins {
46		pinctrl-single,pins = <
47			AM33XX_PADCONF(AM335X_PIN_ECAP0_IN_PWM0_OUT, PIN_INPUT_PULLUP, MUX_MODE4)	 /* ecap0_in_pwm0_out.spi1_sclk */
48			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLUP, MUX_MODE4)	 /* uart1_ctsn.spi1_cs0 */
49			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT_PULLUP, MUX_MODE4)	 /* uart0_ctsn.spi1_d0 */
50			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT_PULLUP, MUX_MODE4)	 /* uart0_rtsn.spi1_d1 */
51		>;
52	};
53};
54
55&davinci_mdio_sw {
56	phy0: ethernet-phy@4 {
57		reg = <4>;
58	};
59};
60
61&cpsw_port1 {
62	phy-handle = <&phy0>;
63	phy-mode = "rmii";
64};
65
66&cpsw_port2 {
67	status = "disabled";
68};
69