1// SPDX-License-Identifier: GPL-2.0-or-later 2/* 3 * Copyright 2012 ST-Ericsson AB 4 */ 5 6#include <dt-bindings/interrupt-controller/irq.h> 7#include <dt-bindings/leds/common.h> 8#include "ste-href-family-pinctrl.dtsi" 9 10/ { 11 memory { 12 device_type = "memory"; 13 reg = <0x00000000 0x20000000>; 14 }; 15 16 battery: battery { 17 compatible = "simple-battery"; 18 battery-type = "lithium-ion-polymer"; 19 }; 20 21 thermal-zones { 22 battery-thermal { 23 /* This zone will be polled by the battery temperature code */ 24 polling-delay = <0>; 25 polling-delay-passive = <0>; 26 thermal-sensors = <&bat_therm>; 27 28 trips { 29 battery-crit-hi { 30 temperature = <70000>; 31 hysteresis = <2000>; 32 type = "critical"; 33 }; 34 }; 35 }; 36 }; 37 38 bat_therm: thermistor { 39 compatible = "murata,ncp18wb473"; 40 io-channels = <&gpadc 0x02>; /* BatTemp */ 41 pullup-uv = <1800000>; 42 pullup-ohm = <230000>; 43 pulldown-ohm = <0>; 44 #thermal-sensor-cells = <0>; 45 }; 46 47 soc { 48 serial@80120000 { 49 pinctrl-names = "default", "sleep"; 50 pinctrl-0 = <&u0_a_1_default>; 51 pinctrl-1 = <&u0_a_1_sleep>; 52 status = "okay"; 53 }; 54 55 /* This UART is unused and thus left disabled */ 56 serial@80121000 { 57 pinctrl-names = "default", "sleep"; 58 pinctrl-0 = <&u1rxtx_a_1_default>; 59 pinctrl-1 = <&u1rxtx_a_1_sleep>; 60 }; 61 62 serial@80007000 { 63 pinctrl-names = "default", "sleep"; 64 pinctrl-0 = <&u2rxtx_c_1_default>; 65 pinctrl-1 = <&u2rxtx_c_1_sleep>; 66 status = "okay"; 67 }; 68 69 i2c@80004000 { 70 pinctrl-names = "default","sleep"; 71 pinctrl-0 = <&i2c0_a_1_default>; 72 pinctrl-1 = <&i2c0_a_1_sleep>; 73 status = "okay"; 74 }; 75 76 i2c@80122000 { 77 pinctrl-names = "default","sleep"; 78 pinctrl-0 = <&i2c1_b_2_default>; 79 pinctrl-1 = <&i2c1_b_2_sleep>; 80 status = "okay"; 81 }; 82 83 i2c@80128000 { 84 pinctrl-names = "default","sleep"; 85 pinctrl-0 = <&i2c2_b_2_default>; 86 pinctrl-1 = <&i2c2_b_2_sleep>; 87 status = "okay"; 88 lp5521@33 { 89 compatible = "national,lp5521"; 90 reg = <0x33>; 91 label = "lp5521_pri"; 92 clock-mode = /bits/ 8 <2>; 93 #address-cells = <1>; 94 #size-cells = <0>; 95 led@0 { 96 reg = <0>; 97 led-cur = /bits/ 8 <0x2f>; 98 max-cur = /bits/ 8 <0x5f>; 99 color = <LED_COLOR_ID_BLUE>; 100 linux,default-trigger = "heartbeat"; 101 }; 102 led@1 { 103 reg = <1>; 104 led-cur = /bits/ 8 <0x2f>; 105 max-cur = /bits/ 8 <0x5f>; 106 color = <LED_COLOR_ID_BLUE>; 107 }; 108 led@2 { 109 reg = <2>; 110 led-cur = /bits/ 8 <0x2f>; 111 max-cur = /bits/ 8 <0x5f>; 112 color = <LED_COLOR_ID_BLUE>; 113 }; 114 }; 115 lp5521@34 { 116 compatible = "national,lp5521"; 117 reg = <0x34>; 118 label = "lp5521_sec"; 119 clock-mode = /bits/ 8 <2>; 120 #address-cells = <1>; 121 #size-cells = <0>; 122 led@0 { 123 reg = <0>; 124 led-cur = /bits/ 8 <0x2f>; 125 max-cur = /bits/ 8 <0x5f>; 126 color = <LED_COLOR_ID_BLUE>; 127 }; 128 led@1 { 129 reg = <1>; 130 led-cur = /bits/ 8 <0x2f>; 131 max-cur = /bits/ 8 <0x5f>; 132 color = <LED_COLOR_ID_BLUE>; 133 }; 134 led@2 { 135 reg = <2>; 136 led-cur = /bits/ 8 <0x2f>; 137 max-cur = /bits/ 8 <0x5f>; 138 color = <LED_COLOR_ID_BLUE>; 139 }; 140 }; 141 bh1780@29 { 142 compatible = "rohm,bh1780gli"; 143 reg = <0x29>; 144 }; 145 }; 146 147 i2c@80110000 { 148 pinctrl-names = "default","sleep"; 149 pinctrl-0 = <&i2c3_c_2_default>; 150 pinctrl-1 = <&i2c3_c_2_sleep>; 151 status = "okay"; 152 }; 153 154 // External Micro SD slot 155 mmc@80126000 { 156 arm,primecell-periphid = <0x10480180>; 157 max-frequency = <100000000>; 158 bus-width = <4>; 159 cap-sd-highspeed; 160 cap-mmc-highspeed; 161 sd-uhs-sdr12; 162 sd-uhs-sdr25; 163 full-pwr-cycle; 164 st,sig-dir-dat0; 165 st,sig-dir-dat2; 166 st,sig-dir-cmd; 167 st,sig-pin-fbclk; 168 vmmc-supply = <&ab8500_ldo_aux3_reg>; 169 vqmmc-supply = <&vmmci>; 170 pinctrl-names = "default", "sleep"; 171 pinctrl-0 = <&mc0_a_1_default &sdi0_default_mode>; 172 pinctrl-1 = <&mc0_a_1_sleep>; 173 174 status = "okay"; 175 }; 176 177 // WLAN SDIO channel 178 mmc@80118000 { 179 arm,primecell-periphid = <0x10480180>; 180 max-frequency = <100000000>; 181 bus-width = <4>; 182 non-removable; 183 pinctrl-names = "default", "sleep"; 184 pinctrl-0 = <&mc1_a_1_default>; 185 pinctrl-1 = <&mc1_a_1_sleep>; 186 187 status = "okay"; 188 }; 189 190 // PoP:ed eMMC 191 mmc@80005000 { 192 arm,primecell-periphid = <0x10480180>; 193 max-frequency = <100000000>; 194 bus-width = <8>; 195 cap-mmc-highspeed; 196 non-removable; 197 no-sdio; 198 no-sd; 199 vmmc-supply = <&db8500_vsmps2_reg>; 200 pinctrl-names = "default", "sleep"; 201 pinctrl-0 = <&mc2_a_1_default>; 202 pinctrl-1 = <&mc2_a_1_sleep>; 203 204 status = "okay"; 205 }; 206 207 // On-board eMMC 208 mmc@80114000 { 209 arm,primecell-periphid = <0x10480180>; 210 max-frequency = <100000000>; 211 bus-width = <8>; 212 cap-mmc-highspeed; 213 non-removable; 214 no-sdio; 215 no-sd; 216 vmmc-supply = <&ab8500_ldo_aux2_reg>; 217 pinctrl-names = "default", "sleep"; 218 pinctrl-0 = <&mc4_a_1_default>; 219 pinctrl-1 = <&mc4_a_1_sleep>; 220 221 status = "okay"; 222 }; 223 224 msp0: msp@80123000 { 225 pinctrl-names = "default"; 226 pinctrl-0 = <&msp0txrxtfstck_a_1_default>; 227 status = "okay"; 228 }; 229 230 msp1: msp@80124000 { 231 pinctrl-names = "default"; 232 pinctrl-0 = <&msp1txrx_a_1_default>; 233 status = "okay"; 234 }; 235 236 msp2: msp@80117000 { 237 pinctrl-names = "default"; 238 pinctrl-0 = <&msp2_a_1_default>; 239 }; 240 241 msp3: msp@80125000 { 242 status = "okay"; 243 }; 244 245 pinctrl { 246 sdi0 { 247 sdi0_default_mode: sdi0_default { 248 /* Some boards set additional settings here */ 249 }; 250 }; 251 }; 252 253 mcde@a0350000 { 254 pinctrl-names = "default", "sleep"; 255 pinctrl-0 = <&lcd_default_mode>; 256 pinctrl-1 = <&lcd_sleep_mode>; 257 }; 258 }; 259}; 260