1// SPDX-License-Identifier: GPL-2.0 2/* 3 * Device Tree Source for the Lager board 4 * 5 * Copyright (C) 2013-2014 Renesas Solutions Corp. 6 * Copyright (C) 2014 Cogent Embedded, Inc. 7 * Copyright (C) 2015-2016 Renesas Electronics Corporation 8 */ 9 10/* 11 * SSI-AK4643 12 * 13 * SW1: 1: AK4643 14 * 2: CN22 15 * 3: ADV7511 16 * 17 * This command is required when Playback/Capture 18 * 19 * amixer set "LINEOUT Mixer DACL" on 20 * amixer set "DVC Out" 100% 21 * amixer set "DVC In" 100% 22 * 23 * You can use Mute 24 * 25 * amixer set "DVC Out Mute" on 26 * amixer set "DVC In Mute" on 27 * 28 * You can use Volume Ramp 29 * 30 * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps" 31 * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps" 32 * amixer set "DVC Out Ramp" on 33 * aplay xxx.wav & 34 * amixer set "DVC Out" 80% // Volume Down 35 * amixer set "DVC Out" 100% // Volume Up 36 */ 37 38/dts-v1/; 39#include "r8a7790.dtsi" 40#include <dt-bindings/gpio/gpio.h> 41#include <dt-bindings/input/input.h> 42 43/ { 44 model = "Lager"; 45 compatible = "renesas,lager", "renesas,r8a7790"; 46 47 aliases { 48 serial0 = &scif0; 49 serial1 = &scifa1; 50 i2c8 = &gpioi2c1; 51 i2c9 = &gpioi2c2; 52 i2c10 = &i2cexio0; 53 i2c11 = &i2cexio1; 54 i2c12 = &i2chdmi; 55 i2c13 = &i2cpwr; 56 mmc0 = &mmcif1; 57 mmc1 = &sdhi0; 58 mmc2 = &sdhi2; 59 }; 60 61 chosen { 62 bootargs = "ignore_loglevel rw root=/dev/nfs ip=on"; 63 stdout-path = "serial0:115200n8"; 64 }; 65 66 memory@40000000 { 67 device_type = "memory"; 68 reg = <0 0x40000000 0 0x40000000>; 69 }; 70 71 memory@140000000 { 72 device_type = "memory"; 73 reg = <1 0x40000000 0 0xc0000000>; 74 }; 75 76 lbsc { 77 #address-cells = <1>; 78 #size-cells = <1>; 79 }; 80 81 keyboard { 82 compatible = "gpio-keys"; 83 84 pinctrl-0 = <&keyboard_pins>; 85 pinctrl-names = "default"; 86 87 one { 88 linux,code = <KEY_1>; 89 label = "SW2-1"; 90 wakeup-source; 91 debounce-interval = <20>; 92 gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; 93 }; 94 two { 95 linux,code = <KEY_2>; 96 label = "SW2-2"; 97 wakeup-source; 98 debounce-interval = <20>; 99 gpios = <&gpio1 24 GPIO_ACTIVE_LOW>; 100 }; 101 three { 102 linux,code = <KEY_3>; 103 label = "SW2-3"; 104 wakeup-source; 105 debounce-interval = <20>; 106 gpios = <&gpio1 26 GPIO_ACTIVE_LOW>; 107 }; 108 four { 109 linux,code = <KEY_4>; 110 label = "SW2-4"; 111 wakeup-source; 112 debounce-interval = <20>; 113 gpios = <&gpio1 28 GPIO_ACTIVE_LOW>; 114 }; 115 }; 116 117 leds { 118 compatible = "gpio-leds"; 119 led6 { 120 gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>; 121 }; 122 led7 { 123 gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>; 124 }; 125 led8 { 126 gpios = <&gpio5 17 GPIO_ACTIVE_HIGH>; 127 }; 128 }; 129 130 fixedregulator3v3: regulator-3v3 { 131 compatible = "regulator-fixed"; 132 regulator-name = "fixed-3.3V"; 133 regulator-min-microvolt = <3300000>; 134 regulator-max-microvolt = <3300000>; 135 regulator-boot-on; 136 regulator-always-on; 137 }; 138 139 vcc_sdhi0: regulator-vcc-sdhi0 { 140 compatible = "regulator-fixed"; 141 142 regulator-name = "SDHI0 Vcc"; 143 regulator-min-microvolt = <3300000>; 144 regulator-max-microvolt = <3300000>; 145 146 gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>; 147 enable-active-high; 148 }; 149 150 vccq_sdhi0: regulator-vccq-sdhi0 { 151 compatible = "regulator-gpio"; 152 153 regulator-name = "SDHI0 VccQ"; 154 regulator-min-microvolt = <1800000>; 155 regulator-max-microvolt = <3300000>; 156 157 gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; 158 gpios-states = <1>; 159 states = <3300000 1>, <1800000 0>; 160 }; 161 162 vcc_sdhi2: regulator-vcc-sdhi2 { 163 compatible = "regulator-fixed"; 164 165 regulator-name = "SDHI2 Vcc"; 166 regulator-min-microvolt = <3300000>; 167 regulator-max-microvolt = <3300000>; 168 169 gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>; 170 enable-active-high; 171 }; 172 173 vccq_sdhi2: regulator-vccq-sdhi2 { 174 compatible = "regulator-gpio"; 175 176 regulator-name = "SDHI2 VccQ"; 177 regulator-min-microvolt = <1800000>; 178 regulator-max-microvolt = <3300000>; 179 180 gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>; 181 gpios-states = <1>; 182 states = <3300000 1>, <1800000 0>; 183 }; 184 185 audio_clock: audio_clock { 186 compatible = "fixed-clock"; 187 #clock-cells = <0>; 188 clock-frequency = <11289600>; 189 }; 190 191 rsnd_ak4643: sound { 192 compatible = "simple-audio-card"; 193 194 simple-audio-card,format = "left_j"; 195 simple-audio-card,bitclock-master = <&sndcodec>; 196 simple-audio-card,frame-master = <&sndcodec>; 197 198 sndcpu: simple-audio-card,cpu { 199 sound-dai = <&rcar_sound>; 200 }; 201 202 sndcodec: simple-audio-card,codec { 203 sound-dai = <&ak4643>; 204 clocks = <&audio_clock>; 205 }; 206 }; 207 208 vga-encoder { 209 compatible = "adi,adv7123"; 210 211 ports { 212 #address-cells = <1>; 213 #size-cells = <0>; 214 215 port@0 { 216 reg = <0>; 217 adv7123_in: endpoint { 218 remote-endpoint = <&du_out_rgb>; 219 }; 220 }; 221 port@1 { 222 reg = <1>; 223 adv7123_out: endpoint { 224 remote-endpoint = <&vga_in>; 225 }; 226 }; 227 }; 228 }; 229 230 vga { 231 compatible = "vga-connector"; 232 233 port { 234 vga_in: endpoint { 235 remote-endpoint = <&adv7123_out>; 236 }; 237 }; 238 }; 239 240 hdmi-in { 241 compatible = "hdmi-connector"; 242 type = "a"; 243 244 port { 245 hdmi_con_in: endpoint { 246 remote-endpoint = <&adv7612_in>; 247 }; 248 }; 249 }; 250 251 cec_clock: cec-clock { 252 compatible = "fixed-clock"; 253 #clock-cells = <0>; 254 clock-frequency = <12000000>; 255 }; 256 257 hdmi-out { 258 compatible = "hdmi-connector"; 259 type = "a"; 260 261 port { 262 hdmi_con_out: endpoint { 263 remote-endpoint = <&adv7511_out>; 264 }; 265 }; 266 }; 267 268 x2_clk: x2-clock { 269 compatible = "fixed-clock"; 270 #clock-cells = <0>; 271 clock-frequency = <148500000>; 272 }; 273 274 x13_clk: x13-clock { 275 compatible = "fixed-clock"; 276 #clock-cells = <0>; 277 clock-frequency = <148500000>; 278 }; 279 280 gpioi2c1: i2c-8 { 281 #address-cells = <1>; 282 #size-cells = <0>; 283 compatible = "i2c-gpio"; 284 status = "disabled"; 285 scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 286 sda-gpios = <&gpio1 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 287 i2c-gpio,delay-us = <5>; 288 }; 289 290 gpioi2c2: i2c-9 { 291 #address-cells = <1>; 292 #size-cells = <0>; 293 compatible = "i2c-gpio"; 294 status = "disabled"; 295 scl-gpios = <&gpio5 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 296 sda-gpios = <&gpio5 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; 297 i2c-gpio,delay-us = <5>; 298 }; 299 300 /* 301 * IIC0/I2C0 is routed to EXIO connector A, pins 114 (SCL) + 116 (SDA) only. 302 * We use the I2C demuxer, so the desired IP core can be selected at runtime 303 * depending on the use case (e.g. DMA with IIC0 or slave support with I2C0). 304 * Note: For testing the I2C slave feature, it is convenient to connect this 305 * bus with IIC3 on pins 110 (SCL) + 112 (SDA), select I2C0 at runtime, and 306 * instantiate the slave device at runtime according to the documentation. 307 * You can then communicate with the slave via IIC3. 308 * 309 * IIC0/I2C0 does not appear to support fallback to GPIO. 310 */ 311 i2cexio0: i2c-10 { 312 compatible = "i2c-demux-pinctrl"; 313 i2c-parent = <&iic0>, <&i2c0>; 314 i2c-bus-name = "i2c-exio0"; 315 #address-cells = <1>; 316 #size-cells = <0>; 317 }; 318 319 /* 320 * IIC1/I2C1 is routed to EXIO connector A, pins 78 (SCL) + 80 (SDA). 321 * This is similar to the arangement described for i2cexio0 (above) 322 * with a fallback to GPIO also provided. 323 */ 324 i2cexio1: i2c-11 { 325 compatible = "i2c-demux-pinctrl"; 326 i2c-parent = <&iic1>, <&i2c1>, <&gpioi2c1>; 327 i2c-bus-name = "i2c-exio1"; 328 #address-cells = <1>; 329 #size-cells = <0>; 330 }; 331 332 /* 333 * IIC2 and I2C2 may be switched using pinmux. 334 * A fallback to GPIO is also provided. 335 */ 336 i2chdmi: i2c-12 { 337 compatible = "i2c-demux-pinctrl"; 338 i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>; 339 i2c-bus-name = "i2c-hdmi"; 340 #address-cells = <1>; 341 #size-cells = <0>; 342 343 ak4643: codec@12 { 344 compatible = "asahi-kasei,ak4643"; 345 #sound-dai-cells = <0>; 346 reg = <0x12>; 347 }; 348 349 composite-in@20 { 350 compatible = "adi,adv7180"; 351 reg = <0x20>; 352 353 port { 354 adv7180: endpoint { 355 bus-width = <8>; 356 remote-endpoint = <&vin1ep0>; 357 }; 358 }; 359 }; 360 361 hdmi@39 { 362 compatible = "adi,adv7511w"; 363 reg = <0x39>; 364 interrupt-parent = <&gpio1>; 365 interrupts = <15 IRQ_TYPE_LEVEL_LOW>; 366 clocks = <&cec_clock>; 367 clock-names = "cec"; 368 369 adi,input-depth = <8>; 370 adi,input-colorspace = "rgb"; 371 adi,input-clock = "1x"; 372 373 ports { 374 #address-cells = <1>; 375 #size-cells = <0>; 376 377 port@0 { 378 reg = <0>; 379 adv7511_in: endpoint { 380 remote-endpoint = <&lvds0_out>; 381 }; 382 }; 383 384 port@1 { 385 reg = <1>; 386 adv7511_out: endpoint { 387 remote-endpoint = <&hdmi_con_out>; 388 }; 389 }; 390 }; 391 }; 392 393 hdmi-in@4c { 394 compatible = "adi,adv7612"; 395 reg = <0x4c>; 396 interrupt-parent = <&gpio1>; 397 interrupts = <20 IRQ_TYPE_LEVEL_LOW>; 398 default-input = <0>; 399 400 ports { 401 #address-cells = <1>; 402 #size-cells = <0>; 403 404 port@0 { 405 reg = <0>; 406 adv7612_in: endpoint { 407 remote-endpoint = <&hdmi_con_in>; 408 }; 409 }; 410 411 port@2 { 412 reg = <2>; 413 adv7612_out: endpoint { 414 remote-endpoint = <&vin0ep2>; 415 }; 416 }; 417 }; 418 }; 419 }; 420 421 /* 422 * IIC3 and I2C3 may be switched using pinmux. 423 * IIC3/I2C3 does not appear to support fallback to GPIO. 424 */ 425 i2cpwr: i2c-13 { 426 compatible = "i2c-demux-pinctrl"; 427 pinctrl-names = "default"; 428 pinctrl-0 = <&pmic_irq_pins>; 429 i2c-parent = <&iic3>, <&i2c3>; 430 i2c-bus-name = "i2c-pwr"; 431 #address-cells = <1>; 432 #size-cells = <0>; 433 434 pmic@58 { 435 compatible = "dlg,da9063"; 436 reg = <0x58>; 437 interrupt-parent = <&irqc0>; 438 interrupts = <2 IRQ_TYPE_LEVEL_LOW>; 439 interrupt-controller; 440 441 rtc { 442 compatible = "dlg,da9063-rtc"; 443 }; 444 445 watchdog { 446 compatible = "dlg,da9063-watchdog"; 447 }; 448 }; 449 450 vdd_dvfs: regulator@68 { 451 compatible = "dlg,da9210"; 452 reg = <0x68>; 453 interrupt-parent = <&irqc0>; 454 interrupts = <2 IRQ_TYPE_LEVEL_LOW>; 455 456 regulator-min-microvolt = <1000000>; 457 regulator-max-microvolt = <1000000>; 458 regulator-boot-on; 459 regulator-always-on; 460 }; 461 }; 462}; 463 464&du { 465 pinctrl-0 = <&du_pins>; 466 pinctrl-names = "default"; 467 status = "okay"; 468 469 clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>, 470 <&x13_clk>, <&x2_clk>; 471 clock-names = "du.0", "du.1", "du.2", "dclkin.0", "dclkin.1"; 472 473 ports { 474 port@0 { 475 endpoint { 476 remote-endpoint = <&adv7123_in>; 477 }; 478 }; 479 }; 480}; 481 482&lvds0 { 483 status = "okay"; 484 485 ports { 486 port@1 { 487 endpoint { 488 remote-endpoint = <&adv7511_in>; 489 }; 490 }; 491 }; 492}; 493 494&lvds1 { 495 ports { 496 port@1 { 497 lvds_connector: endpoint { 498 }; 499 }; 500 }; 501}; 502 503&extal_clk { 504 clock-frequency = <20000000>; 505}; 506 507&pfc { 508 pinctrl-0 = <&scif_clk_pins>; 509 pinctrl-names = "default"; 510 511 du_pins: du { 512 groups = "du_rgb666", "du_sync_1", "du_clk_out_0"; 513 function = "du"; 514 }; 515 516 scif0_pins: scif0 { 517 groups = "scif0_data"; 518 function = "scif0"; 519 }; 520 521 scif_clk_pins: scif_clk { 522 groups = "scif_clk"; 523 function = "scif_clk"; 524 }; 525 526 ether_pins: ether { 527 groups = "eth_link", "eth_mdio", "eth_rmii"; 528 function = "eth"; 529 }; 530 531 phy1_pins: phy1 { 532 groups = "intc_irq0"; 533 function = "intc"; 534 }; 535 536 scifa1_pins: scifa1 { 537 groups = "scifa1_data"; 538 function = "scifa1"; 539 }; 540 541 sdhi0_pins: sd0 { 542 groups = "sdhi0_data4", "sdhi0_ctrl"; 543 function = "sdhi0"; 544 power-source = <3300>; 545 }; 546 547 sdhi0_pins_uhs: sd0_uhs { 548 groups = "sdhi0_data4", "sdhi0_ctrl"; 549 function = "sdhi0"; 550 power-source = <1800>; 551 }; 552 553 sdhi2_pins: sd2 { 554 groups = "sdhi2_data4", "sdhi2_ctrl"; 555 function = "sdhi2"; 556 power-source = <3300>; 557 }; 558 559 sdhi2_pins_uhs: sd2_uhs { 560 groups = "sdhi2_data4", "sdhi2_ctrl"; 561 function = "sdhi2"; 562 power-source = <1800>; 563 }; 564 565 mmc1_pins: mmc1 { 566 groups = "mmc1_data8", "mmc1_ctrl"; 567 function = "mmc1"; 568 }; 569 570 qspi_pins: qspi { 571 groups = "qspi_ctrl", "qspi_data4"; 572 function = "qspi"; 573 }; 574 575 msiof1_pins: msiof1 { 576 groups = "msiof1_clk", "msiof1_sync", "msiof1_rx", 577 "msiof1_tx"; 578 function = "msiof1"; 579 }; 580 581 i2c0_pins: i2c0 { 582 groups = "i2c0"; 583 function = "i2c0"; 584 }; 585 586 iic0_pins: iic0 { 587 groups = "iic0"; 588 function = "iic0"; 589 }; 590 591 i2c1_pins: i2c1 { 592 groups = "i2c1"; 593 function = "i2c1"; 594 }; 595 596 iic1_pins: iic1 { 597 groups = "iic1"; 598 function = "iic1"; 599 }; 600 601 i2c2_pins: i2c2 { 602 groups = "i2c2"; 603 function = "i2c2"; 604 }; 605 606 iic2_pins: iic2 { 607 groups = "iic2"; 608 function = "iic2"; 609 }; 610 611 i2c3_pins: i2c3 { 612 groups = "i2c3"; 613 function = "i2c3"; 614 }; 615 616 iic3_pins: iic3 { 617 groups = "iic3"; 618 function = "iic3"; 619 }; 620 621 pmic_irq_pins: pmicirq { 622 groups = "intc_irq2"; 623 function = "intc"; 624 }; 625 626 hsusb_pins: hsusb { 627 groups = "usb0_ovc_vbus"; 628 function = "usb0"; 629 }; 630 631 usb0_pins: usb0 { 632 groups = "usb0"; 633 function = "usb0"; 634 }; 635 636 usb1_pins: usb1 { 637 groups = "usb1"; 638 function = "usb1"; 639 }; 640 641 usb2_pins: usb2 { 642 groups = "usb2"; 643 function = "usb2"; 644 }; 645 646 vin0_pins: vin0 { 647 groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk"; 648 function = "vin0"; 649 }; 650 651 vin1_pins: vin1 { 652 groups = "vin1_data8", "vin1_clk"; 653 function = "vin1"; 654 }; 655 656 sound_pins: sound { 657 groups = "ssi0129_ctrl", "ssi0_data", "ssi1_data"; 658 function = "ssi"; 659 }; 660 661 sound_clk_pins: sound_clk { 662 groups = "audio_clk_a"; 663 function = "audio_clk"; 664 }; 665 666 keyboard_pins: keyboard { 667 pins = "GP_1_14", "GP_1_24", "GP_1_26", "GP_1_28"; 668 bias-pull-up; 669 }; 670}; 671 672ðer { 673 pinctrl-0 = <ðer_pins>, <&phy1_pins>; 674 pinctrl-names = "default"; 675 676 phy-handle = <&phy1>; 677 renesas,ether-link-active-low; 678 status = "okay"; 679 680 phy1: ethernet-phy@1 { 681 compatible = "ethernet-phy-id0022.1537", 682 "ethernet-phy-ieee802.3-c22"; 683 reg = <1>; 684 interrupt-parent = <&irqc0>; 685 interrupts = <0 IRQ_TYPE_LEVEL_LOW>; 686 micrel,led-mode = <1>; 687 reset-gpios = <&gpio5 31 GPIO_ACTIVE_LOW>; 688 }; 689}; 690 691&cmt0 { 692 status = "okay"; 693}; 694 695&mmcif1 { 696 pinctrl-0 = <&mmc1_pins>; 697 pinctrl-names = "default"; 698 699 vmmc-supply = <&fixedregulator3v3>; 700 bus-width = <8>; 701 non-removable; 702 status = "okay"; 703}; 704 705&sata1 { 706 status = "okay"; 707}; 708 709&qspi { 710 pinctrl-0 = <&qspi_pins>; 711 pinctrl-names = "default"; 712 713 status = "okay"; 714 715 flash: flash@0 { 716 compatible = "spansion,s25fl512s", "jedec,spi-nor"; 717 reg = <0>; 718 spi-max-frequency = <30000000>; 719 spi-tx-bus-width = <4>; 720 spi-rx-bus-width = <4>; 721 spi-cpha; 722 spi-cpol; 723 m25p,fast-read; 724 725 partitions { 726 compatible = "fixed-partitions"; 727 #address-cells = <1>; 728 #size-cells = <1>; 729 730 partition@0 { 731 label = "loader"; 732 reg = <0x00000000 0x00040000>; 733 read-only; 734 }; 735 partition@40000 { 736 label = "user"; 737 reg = <0x00040000 0x00400000>; 738 read-only; 739 }; 740 partition@440000 { 741 label = "flash"; 742 reg = <0x00440000 0x03bc0000>; 743 }; 744 }; 745 }; 746}; 747 748&scif0 { 749 pinctrl-0 = <&scif0_pins>; 750 pinctrl-names = "default"; 751 752 status = "okay"; 753}; 754 755&scifa1 { 756 pinctrl-0 = <&scifa1_pins>; 757 pinctrl-names = "default"; 758 759 status = "okay"; 760}; 761 762&scif_clk { 763 clock-frequency = <14745600>; 764}; 765 766&msiof1 { 767 pinctrl-0 = <&msiof1_pins>; 768 pinctrl-names = "default"; 769 770 status = "okay"; 771 772 pmic: pmic@0 { 773 compatible = "renesas,r2a11302ft"; 774 reg = <0>; 775 spi-max-frequency = <6000000>; 776 spi-cpol; 777 spi-cpha; 778 }; 779}; 780 781&sdhi0 { 782 pinctrl-0 = <&sdhi0_pins>; 783 pinctrl-1 = <&sdhi0_pins_uhs>; 784 pinctrl-names = "default", "state_uhs"; 785 786 vmmc-supply = <&vcc_sdhi0>; 787 vqmmc-supply = <&vccq_sdhi0>; 788 cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>; 789 sd-uhs-sdr50; 790 sd-uhs-sdr104; 791 status = "okay"; 792}; 793 794&sdhi2 { 795 pinctrl-0 = <&sdhi2_pins>; 796 pinctrl-1 = <&sdhi2_pins_uhs>; 797 pinctrl-names = "default", "state_uhs"; 798 799 vmmc-supply = <&vcc_sdhi2>; 800 vqmmc-supply = <&vccq_sdhi2>; 801 cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>; 802 sd-uhs-sdr50; 803 status = "okay"; 804}; 805 806&cpu0 { 807 cpu0-supply = <&vdd_dvfs>; 808}; 809 810&i2c0 { 811 pinctrl-0 = <&i2c0_pins>; 812 pinctrl-names = "i2c-exio0"; 813}; 814 815&iic0 { 816 pinctrl-0 = <&iic0_pins>; 817 pinctrl-names = "i2c-exio0"; 818}; 819 820&i2c1 { 821 pinctrl-0 = <&i2c1_pins>; 822 pinctrl-names = "i2c-exio1"; 823}; 824 825&iic1 { 826 pinctrl-0 = <&iic1_pins>; 827 pinctrl-names = "i2c-exio1"; 828}; 829 830&i2c2 { 831 pinctrl-0 = <&i2c2_pins>; 832 pinctrl-names = "i2c-hdmi"; 833 834 clock-frequency = <100000>; 835}; 836 837&iic2 { 838 pinctrl-0 = <&iic2_pins>; 839 pinctrl-names = "i2c-hdmi"; 840 841 clock-frequency = <100000>; 842}; 843 844&i2c3 { 845 pinctrl-0 = <&i2c3_pins>; 846 pinctrl-names = "i2c-pwr"; 847}; 848 849&iic3 { 850 pinctrl-0 = <&iic3_pins>; 851 pinctrl-names = "i2c-pwr"; 852}; 853 854&pci0 { 855 status = "okay"; 856 pinctrl-0 = <&usb0_pins>; 857 pinctrl-names = "default"; 858}; 859 860&pci1 { 861 status = "okay"; 862 pinctrl-0 = <&usb1_pins>; 863 pinctrl-names = "default"; 864}; 865 866&xhci { 867 status = "okay"; 868 pinctrl-0 = <&usb2_pins>; 869 pinctrl-names = "default"; 870}; 871 872&pci2 { 873 status = "okay"; 874 pinctrl-0 = <&usb2_pins>; 875 pinctrl-names = "default"; 876}; 877 878&hsusb { 879 status = "okay"; 880 pinctrl-0 = <&hsusb_pins>; 881 pinctrl-names = "default"; 882 renesas,enable-gpio = <&gpio5 18 GPIO_ACTIVE_HIGH>; 883}; 884 885&usbphy { 886 status = "okay"; 887}; 888 889/* HDMI video input */ 890&vin0 { 891 pinctrl-0 = <&vin0_pins>; 892 pinctrl-names = "default"; 893 894 status = "okay"; 895 896 port { 897 vin0ep2: endpoint { 898 remote-endpoint = <&adv7612_out>; 899 bus-width = <24>; 900 hsync-active = <0>; 901 vsync-active = <0>; 902 pclk-sample = <1>; 903 data-active = <1>; 904 }; 905 }; 906}; 907 908/* composite video input */ 909&vin1 { 910 pinctrl-0 = <&vin1_pins>; 911 pinctrl-names = "default"; 912 913 status = "okay"; 914 915 port { 916 vin1ep0: endpoint { 917 remote-endpoint = <&adv7180>; 918 bus-width = <8>; 919 }; 920 }; 921}; 922 923&rcar_sound { 924 pinctrl-0 = <&sound_pins>, <&sound_clk_pins>; 925 pinctrl-names = "default"; 926 927 /* Single DAI */ 928 #sound-dai-cells = <0>; 929 930 status = "okay"; 931 932 rcar_sound,dai { 933 dai0 { 934 playback = <&ssi0>, <&src2>, <&dvc0>; 935 capture = <&ssi1>, <&src3>, <&dvc1>; 936 }; 937 }; 938}; 939 940&rwdt { 941 timeout-sec = <60>; 942 status = "okay"; 943}; 944 945&ssi1 { 946 shared-pin; 947}; 948