1// SPDX-License-Identifier: GPL-2.0-or-later 2/* 3 * Copyright 2012 Freescale Semiconductor, Inc. 4 * 5 * Author: Fabio Estevam <fabio.estevam@freescale.com> 6 */ 7 8/dts-v1/; 9#include <dt-bindings/gpio/gpio.h> 10#include "imx23.dtsi" 11 12/ { 13 model = "i.MX23 Olinuxino Low Cost Board"; 14 compatible = "olimex,imx23-olinuxino", "fsl,imx23"; 15 16 memory@40000000 { 17 device_type = "memory"; 18 reg = <0x40000000 0x04000000>; 19 }; 20 21 apb@80000000 { 22 apbh@80000000 { 23 ssp0: spi@80010000 { 24 compatible = "fsl,imx23-mmc"; 25 pinctrl-names = "default"; 26 pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>; 27 bus-width = <4>; 28 broken-cd; 29 status = "okay"; 30 }; 31 32 pinctrl@80018000 { 33 pinctrl-names = "default"; 34 pinctrl-0 = <&hog_pins_a>; 35 36 hog_pins_a: hog@0 { 37 reg = <0>; 38 fsl,pinmux-ids = < 39 MX23_PAD_GPMI_ALE__GPIO_0_17 40 >; 41 fsl,drive-strength = <MXS_DRIVE_4mA>; 42 fsl,voltage = <MXS_VOLTAGE_HIGH>; 43 fsl,pull-up = <MXS_PULL_DISABLE>; 44 }; 45 46 led_pin_gpio2_1: led_gpio2_1@0 { 47 reg = <0>; 48 fsl,pinmux-ids = < 49 MX23_PAD_SSP1_DETECT__GPIO_2_1 50 >; 51 fsl,drive-strength = <MXS_DRIVE_4mA>; 52 fsl,voltage = <MXS_VOLTAGE_HIGH>; 53 fsl,pull-up = <MXS_PULL_DISABLE>; 54 }; 55 }; 56 57 ssp1: spi@80034000 { 58 #address-cells = <1>; 59 #size-cells = <0>; 60 compatible = "fsl,imx23-spi"; 61 pinctrl-names = "default"; 62 pinctrl-0 = <&spi2_pins_a>; 63 status = "okay"; 64 }; 65 }; 66 67 apbx@80040000 { 68 lradc@80050000 { 69 status = "okay"; 70 }; 71 72 i2c: i2c@80058000 { 73 pinctrl-names = "default"; 74 pinctrl-0 = <&i2c_pins_b>; 75 status = "okay"; 76 }; 77 78 duart: serial@80070000 { 79 pinctrl-names = "default"; 80 pinctrl-0 = <&duart_pins_a>; 81 status = "okay"; 82 }; 83 84 auart0: serial@8006c000 { 85 pinctrl-names = "default"; 86 pinctrl-0 = <&auart0_2pins_a>; 87 status = "okay"; 88 }; 89 90 usbphy0: usbphy@8007c000 { 91 status = "okay"; 92 }; 93 }; 94 }; 95 96 ahb@80080000 { 97 usb0: usb@80080000 { 98 dr_mode = "host"; 99 vbus-supply = <®_usb0_vbus>; 100 status = "okay"; 101 }; 102 }; 103 104 regulators { 105 compatible = "simple-bus"; 106 #address-cells = <1>; 107 #size-cells = <0>; 108 109 reg_usb0_vbus: regulator@0 { 110 compatible = "regulator-fixed"; 111 reg = <0>; 112 regulator-name = "usb0_vbus"; 113 regulator-min-microvolt = <5000000>; 114 regulator-max-microvolt = <5000000>; 115 enable-active-high; 116 startup-delay-us = <300>; /* LAN9215 requires a POR of 200us minimum */ 117 gpio = <&gpio0 17 0>; 118 }; 119 }; 120 121 leds { 122 compatible = "gpio-leds"; 123 pinctrl-names = "default"; 124 pinctrl-0 = <&led_pin_gpio2_1>; 125 126 user { 127 label = "green"; 128 gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>; 129 }; 130 }; 131}; 132