xref: /freebsd/sys/contrib/device-tree/src/arm/nxp/lpc/lpc3250-phy3250.dts (revision 5f757f3ff9144b609b3c433dfd370cc6bdc191ad) 
1// SPDX-License-Identifier: GPL-2.0-or-later
2/*
3 * PHYTEC phyCORE-LPC3250 board
4 *
5 * Copyright (C) 2015-2019 Vladimir Zapolskiy <vz@mleia.com>
6 * Copyright 2012 Roland Stigge <stigge@antcom.de>
7 */
8
9/dts-v1/;
10#include "lpc32xx.dtsi"
11
12/ {
13	model = "PHYTEC phyCORE-LPC3250 board based on NXP LPC3250";
14	compatible = "phytec,phy3250", "nxp,lpc3250";
15
16	memory@80000000 {
17		device_type = "memory";
18		reg = <0x80000000 0x4000000>;
19	};
20
21	leds {
22		compatible = "gpio-leds";
23
24		led0 { /* red */
25			gpios = <&gpio 5 1 0>; /* GPO_P3 1, GPIO 80, active high */
26			default-state = "off";
27		};
28
29		led1 { /* green */
30			gpios = <&gpio 5 14 0>; /* GPO_P3 14, GPIO 93, active high */
31			linux,default-trigger = "heartbeat";
32		};
33	};
34
35	panel: panel {
36		compatible = "sharp,lq035q7db03";
37		power-supply = <&reg_lcd>;
38
39		port {
40			panel_input: endpoint {
41				remote-endpoint = <&cldc_output>;
42			};
43		};
44	};
45
46	reg_backlight: regulator-backlight {
47		compatible = "regulator-fixed";
48		regulator-name = "backlight";
49		regulator-min-microvolt = <1800000>;
50		regulator-max-microvolt = <1800000>;
51		gpio = <&gpio 5 4 0>;
52		enable-active-high;
53		regulator-boot-on;
54	};
55
56	reg_lcd: regulator-lcd {
57		compatible = "regulator-fixed";
58		regulator-name = "lcd";
59		regulator-min-microvolt = <1800000>;
60		regulator-max-microvolt = <1800000>;
61		gpio = <&gpio 5 0 0>;
62		enable-active-high;
63		regulator-boot-on;
64	};
65
66	reg_sd: regulator-sd {
67		compatible = "regulator-fixed";
68		regulator-name = "sd";
69		regulator-min-microvolt = <3300000>;
70		regulator-max-microvolt = <3300000>;
71		gpio = <&gpio 5 5 0>;
72		enable-active-high;
73		regulator-boot-on;
74	};
75};
76
77&clcd {
78	max-memory-bandwidth = <18710000>;
79	status = "okay";
80
81	port {
82		cldc_output: endpoint {
83			remote-endpoint = <&panel_input>;
84			arm,pl11x,tft-r0g0b0-pads = <0 8 16>;
85		};
86	};
87};
88
89&i2c1 {
90	clock-frequency = <100000>;
91
92	uda1380: uda1380@18 {
93		compatible = "nxp,uda1380";
94		reg = <0x18>;
95		power-gpio = <&gpio 3 10 0>;
96		reset-gpio = <&gpio 3 2 0>;
97		dac-clk = "wspll";
98	};
99
100	pcf8563: rtc@51 {
101		compatible = "nxp,pcf8563";
102		reg = <0x51>;
103	};
104};
105
106&i2c2 {
107	clock-frequency = <100000>;
108};
109
110&i2cusb {
111	clock-frequency = <100000>;
112
113	isp1301: usb-transceiver@2c {
114		compatible = "nxp,isp1301";
115		reg = <0x2c>;
116	};
117};
118
119&key {
120	keypad,num-rows = <1>;
121	keypad,num-columns = <1>;
122	nxp,debounce-delay-ms = <3>;
123	nxp,scan-delay-ms = <34>;
124	linux,keymap = <0x00000002>;
125	status = "okay";
126};
127
128&mac {
129	phy-mode = "rmii";
130	use-iram;
131	status = "okay";
132};
133
134/* Here, choose exactly one from: ohci, usbd */
135&ohci /* &usbd */ {
136	transceiver = <&isp1301>;
137	status = "okay";
138};
139
140&sd {
141	wp-gpios = <&gpio 3 0 0>;
142	cd-gpios = <&gpio 3 1 0>;
143	cd-inverted;
144	bus-width = <4>;
145	vmmc-supply = <&reg_sd>;
146	status = "okay";
147};
148
149/* 64MB Flash via SLC NAND controller */
150&slc {
151	status = "okay";
152
153	nxp,wdr-clks = <14>;
154	nxp,wwidth = <40000000>;
155	nxp,whold = <100000000>;
156	nxp,wsetup = <100000000>;
157	nxp,rdr-clks = <14>;
158	nxp,rwidth = <40000000>;
159	nxp,rhold = <66666666>;
160	nxp,rsetup = <100000000>;
161	nand-on-flash-bbt;
162	gpios = <&gpio 5 19 1>; /* GPO_P3 19, active low */
163
164	partitions {
165		compatible = "fixed-partitions";
166		#address-cells = <1>;
167		#size-cells = <1>;
168
169		mtd0@0 {
170			label = "phy3250-boot";
171			reg = <0x00000000 0x00064000>;
172			read-only;
173		};
174
175		mtd1@64000 {
176			label = "phy3250-uboot";
177			reg = <0x00064000 0x00190000>;
178			read-only;
179		};
180
181		mtd2@1f4000 {
182			label = "phy3250-ubt-prms";
183			reg = <0x001f4000 0x00010000>;
184		};
185
186		mtd3@204000 {
187			label = "phy3250-kernel";
188			reg = <0x00204000 0x00400000>;
189		};
190
191		mtd4@604000 {
192			label = "phy3250-rootfs";
193			reg = <0x00604000 0x039fc000>;
194		};
195	};
196};
197
198&ssp0 {
199	num-cs = <1>;
200	cs-gpios = <&gpio 3 5 0>;
201	status = "okay";
202
203	eeprom: at25@0 {
204		compatible = "atmel,at25";
205		reg = <0>;
206		spi-max-frequency = <5000000>;
207
208		pl022,interface = <0>;
209		pl022,com-mode = <0>;
210		pl022,rx-level-trig = <1>;
211		pl022,tx-level-trig = <1>;
212		pl022,ctrl-len = <11>;
213		pl022,wait-state = <0>;
214		pl022,duplex = <0>;
215
216		at25,byte-len = <0x8000>;
217		at25,addr-mode = <2>;
218		at25,page-size = <64>;
219	};
220};
221
222&tsc {
223	status = "okay";
224};
225
226&uart2 {
227	status = "okay";
228};
229
230&uart3 {
231	status = "okay";
232};
233
234&uart5 {
235	status = "okay";
236};
237