1// SPDX-License-Identifier: (GPL-2.0+ OR MIT) 2 3/dts-v1/; 4 5#include <dt-bindings/gpio/gpio.h> 6#include "imx6q-ba16.dtsi" 7 8/ { 9 model = "Advantech DMS-BA16"; 10 compatible = "advantech,imx6q-dms-ba16", "advantech,imx6q-ba16", "fsl,imx6q"; 11 12 reg_usb_otg_vbus: regulator-usbotgvbus { 13 compatible = "regulator-fixed"; 14 regulator-name = "usb_otg_vbus"; 15 regulator-min-microvolt = <5000000>; 16 regulator-max-microvolt = <5000000>; 17 pinctrl-names = "default"; 18 pinctrl-0 = <&pinctrl_usbotgvbus>; 19 gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>; 20 enable-active-high; 21 }; 22 23 sys_mclk: clock-sys-mclk { 24 compatible = "fixed-clock"; 25 #clock-cells = <0>; 26 clock-frequency = <22000000>; 27 }; 28 29 sound { 30 compatible = "fsl,imx6q-ba16-sgtl5000", 31 "fsl,imx-audio-sgtl5000"; 32 model = "imx6q-ba16-sgtl5000"; 33 ssi-controller = <&ssi1>; 34 audio-codec = <&sgtl5000>; 35 audio-routing = 36 "MIC_IN", "Mic Jack", 37 "Mic Jack", "Mic Bias", 38 "Headphone Jack", "HP_OUT"; 39 mux-int-port = <1>; 40 mux-ext-port = <4>; 41 }; 42}; 43 44&ecspi5 { 45 cs-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; 46 pinctrl-names = "default"; 47 pinctrl-0 = <&pinctrl_ecspi5>; 48 status = "okay"; 49 50 m25_eeprom: flash@0 { 51 compatible = "atmel,at25256B", "atmel,at25"; 52 spi-max-frequency = <20000000>; 53 size = <0x8000>; 54 pagesize = <64>; 55 reg = <0>; 56 address-width = <16>; 57 }; 58}; 59 60&iomuxc { 61 pinctrl_i2c1_gpio: i2c1gpiogrp { 62 fsl,pins = < 63 MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x1b0b0 64 MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x1b0b0 65 >; 66 }; 67 68 pinctrl_i2c2_gpio: i2c2gpiogrp { 69 fsl,pins = < 70 MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x1b0b0 71 MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x1b0b0 72 >; 73 }; 74 75 pinctrl_i2c3_gpio: i2c3gpiogrp { 76 fsl,pins = < 77 MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x1b0b0 78 MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x1b0b0 79 >; 80 }; 81 82 pinctrl_usbotgvbus: usbotgvbusgrp { 83 fsl,pins = < 84 MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 85 MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x000b0 86 >; 87 }; 88}; 89 90&i2c1 { 91 clock-frequency = <100000>; 92 pinctrl-names = "default"; 93 pinctrl-0 = <&pinctrl_i2c1>; 94 status = "okay"; 95 96 sgtl5000: codec@a { 97 compatible = "fsl,sgtl5000"; 98 reg = <0x0a>; 99 clocks = <&sys_mclk>; 100 lrclk-strength = <0x3>; 101 VDDA-supply = <®_1p8v>; 102 VDDIO-supply = <®_3p3v>; 103 }; 104}; 105 106&pwm2 { 107 pinctrl-names = "default"; 108 pinctrl-0 = <&pinctrl_pwm2>; 109 status = "okay"; 110}; 111 112&sata { 113 fsl,no-spread-spectrum; 114 fsl,transmit-atten-16ths = <12>; 115 fsl,transmit-boost-mdB = <3330>; 116 fsl,transmit-level-mV = <1133>; 117 fsl,receive-dpll-mode = <1>; 118 status = "okay"; 119}; 120 121&usbotg { 122 vbus-supply = <®_usb_otg_vbus>; 123 pinctrl-names = "default"; 124 pinctrl-0 = <&pinctrl_usbotg>; 125 dr_mode = "otg"; 126 disable-over-current; 127 status = "okay"; 128}; 129 130&usdhc4 { 131 pinctrl-names = "default"; 132 pinctrl-0 = <&pinctrl_usdhc4>; 133 bus-width = <8>; 134 cd-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>; 135 no-1-8-v; 136 keep-power-in-suspend; 137 wakeup-source; 138 status = "okay"; 139}; 140