1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * Device Tree file for CalAmp LMU5000 board 4 * 5 * Copyright (C) 2013 Adam Porter <porter.adam@gmail.com> 6 */ 7 8/dts-v1/; 9#include "at91sam9g20.dtsi" 10 11/ { 12 model = "CalAmp LMU5000"; 13 compatible = "calamp,lmu5000", "atmel,at91sam9g20", "atmel,at91sam9"; 14 15 chosen { 16 bootargs = "mem=64M console=ttyS0,115200 rootfstype=jffs2"; 17 }; 18 19 memory { 20 reg = <0x20000000 0x4000000>; 21 }; 22 23 clocks { 24 #address-cells = <1>; 25 #size-cells = <1>; 26 ranges; 27 28 main_clock: clock@0 { 29 compatible = "atmel,osc", "fixed-clock"; 30 clock-frequency = <18432000>; 31 }; 32 }; 33}; 34 35&dbgu { 36 status = "okay"; 37}; 38 39&ebi { 40 status = "okay"; 41 42 nand_controller: nand-controller { 43 pinctrl-0 = <&pinctrl_nand_cs &pinctrl_nand_rb>; 44 pinctrl-names = "default"; 45 status = "okay"; 46 47 nand@3 { 48 reg = <0x3 0x0 0x800000>; 49 rb-gpios = <&pioC 13 GPIO_ACTIVE_HIGH>; 50 cs-gpios = <&pioC 14 GPIO_ACTIVE_HIGH>; 51 nand-bus-width = <8>; 52 nand-ecc-mode = "soft"; 53 nand-on-flash-bbt; 54 label = "atmel_nand"; 55 status = "okay"; 56 57 partitions { 58 compatible = "fixed-partitions"; 59 #address-cells = <1>; 60 #size-cells = <1>; 61 62 kernel@0 { 63 label = "kernel"; 64 reg = <0x0 0x400000>; 65 }; 66 67 rootfs@400000 { 68 label = "rootfs"; 69 reg = <0x400000 0x3C00000>; 70 }; 71 72 user1@4000000 { 73 label = "user1"; 74 reg = <0x4000000 0x2000000>; 75 }; 76 77 user2@6000000 { 78 label = "user2"; 79 reg = <0x6000000 0x2000000>; 80 }; 81 }; 82 }; 83 }; 84}; 85 86&macb0 { 87 phy-mode = "mii"; 88 status = "okay"; 89}; 90 91&pinctrl { 92 board { 93 pinctrl_pck0_as_mck: pck0_as_mck { 94 atmel,pins = <AT91_PIOC 1 AT91_PERIPH_B AT91_PINCTRL_NONE>; 95 }; 96 }; 97 98 usb0 { 99 pinctrl_usb1_vbus_gpio: usb0_vbus_gpio { 100 atmel,pins = <AT91_PIOC 5 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; 101 }; 102 }; 103}; 104 105&ssc0 { 106 status = "okay"; 107 pinctrl-0 = <&pinctrl_ssc0_tx>; 108}; 109 110&uart0 { 111 status = "okay"; 112}; 113 114&uart1 { 115 status = "okay"; 116}; 117 118&usart0 { 119 pinctrl-0 = 120 <&pinctrl_usart0 121 &pinctrl_usart0_rts 122 &pinctrl_usart0_cts 123 &pinctrl_usart0_dtr_dsr 124 &pinctrl_usart0_dcd 125 &pinctrl_usart0_ri>; 126 status = "okay"; 127}; 128 129&usart2 { 130 status = "okay"; 131}; 132 133&usb0 { 134 num-ports = <2>; 135 status = "okay"; 136}; 137 138&usb1 { 139 pinctrl-names = "default"; 140 pinctrl-0 = <&pinctrl_usb1_vbus_gpio>; 141 atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>; 142 status = "okay"; 143}; 144 145&watchdog { 146 status = "okay"; 147}; 148