1// SPDX-License-Identifier: GPL-2.0 2/dts-v1/; 3 4#include "kirkwood.dtsi" 5#include "kirkwood-6281.dtsi" 6 7/ { 8 model = "Seagate FreeAgent Dockstar"; 9 compatible = "seagate,dockstar", "marvell,kirkwood-88f6281", "marvell,kirkwood"; 10 11 memory { 12 device_type = "memory"; 13 reg = <0x00000000 0x8000000>; 14 }; 15 16 chosen { 17 bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; 18 stdout-path = &uart0; 19 }; 20 21 ocp@f1000000 { 22 pinctrl: pin-controller@10000 { 23 pmx_usb_power_enable: pmx-usb-power-enable { 24 marvell,pins = "mpp29"; 25 marvell,function = "gpio"; 26 }; 27 pmx_led_green: pmx-led-green { 28 marvell,pins = "mpp46"; 29 marvell,function = "gpio"; 30 }; 31 pmx_led_orange: pmx-led-orange { 32 marvell,pins = "mpp47"; 33 marvell,function = "gpio"; 34 }; 35 }; 36 serial@12000 { 37 status = "okay"; 38 }; 39 }; 40 gpio-leds { 41 compatible = "gpio-leds"; 42 pinctrl-0 = <&pmx_led_green &pmx_led_orange>; 43 pinctrl-names = "default"; 44 45 health { 46 label = "status:green:health"; 47 gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; 48 default-state = "keep"; 49 }; 50 fault { 51 label = "status:orange:fault"; 52 gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; 53 }; 54 }; 55 regulators { 56 compatible = "simple-bus"; 57 #address-cells = <1>; 58 #size-cells = <0>; 59 pinctrl-0 = <&pmx_usb_power_enable>; 60 pinctrl-names = "default"; 61 62 usb_power: regulator@1 { 63 compatible = "regulator-fixed"; 64 reg = <1>; 65 regulator-name = "USB Power"; 66 regulator-min-microvolt = <5000000>; 67 regulator-max-microvolt = <5000000>; 68 enable-active-high; 69 regulator-always-on; 70 regulator-boot-on; 71 gpio = <&gpio0 29 0>; 72 }; 73 }; 74}; 75 76&nand { 77 status = "okay"; 78 79 partition@0 { 80 label = "u-boot"; 81 reg = <0x0000000 0x100000>; 82 read-only; 83 }; 84 85 partition@100000 { 86 label = "uImage"; 87 reg = <0x0100000 0x400000>; 88 }; 89 90 partition@500000 { 91 label = "data"; 92 reg = <0x0500000 0xfb00000>; 93 }; 94}; 95 96&mdio { 97 status = "okay"; 98 99 ethphy0: ethernet-phy@0 { 100 compatible = "marvell,88e1116"; 101 reg = <0>; 102 }; 103}; 104 105ð0 { 106 status = "okay"; 107 ethernet0-port@0 { 108 phy-handle = <ðphy0>; 109 }; 110}; 111