xref: /freebsd/sys/contrib/device-tree/src/arm/marvell/armada-385-linksys.dtsi (revision a0ca4af9455b844c5e094fc1b09b1390ffa979fc) 
1// SPDX-License-Identifier: (GPL-2.0 OR MIT)
2/*
3 * Device Tree include file for Armada 385 based Linksys boards
4 *
5 * Copyright (C) 2015 Imre Kaloz <kaloz@openwrt.org>
6 */
7
8#include <dt-bindings/gpio/gpio.h>
9#include <dt-bindings/input/input.h>
10#include "armada-385.dtsi"
11
12/ {
13	model = "Linksys boards based on Armada 385";
14	compatible = "linksys,armada385", "marvell,armada385",
15		     "marvell,armada380";
16
17	chosen {
18		stdout-path = "serial0:115200n8";
19	};
20
21	memory {
22		device_type = "memory";
23		reg = <0x00000000 0x20000000>; /* 512 MiB */
24	};
25
26	soc {
27		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
28			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
29			  MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
30			  MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
31			  MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
32	};
33
34	usb3_1_phy: usb3_1-phy {
35		compatible = "usb-nop-xceiv";
36		vcc-supply = <&usb3_1_vbus>;
37		#phy-cells = <0>;
38	};
39
40	usb3_1_vbus: usb3_1-vbus {
41		compatible = "regulator-fixed";
42		pinctrl-names = "default";
43		pinctrl-0 = <&usb3_1_vbus_pins>;
44		regulator-name = "usb3_1-vbus";
45		regulator-min-microvolt = <5000000>;
46		regulator-max-microvolt = <5000000>;
47		enable-active-high;
48		gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>;
49	};
50
51	gpio_keys: gpio-keys {
52		compatible = "gpio-keys";
53		pinctrl-0 = <&gpio_keys_pins>;
54		pinctrl-names = "default";
55
56		button-wps {
57			label = "WPS";
58			linux,code = <KEY_WPS_BUTTON>;
59			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
60		};
61
62		button-reset {
63			label = "Factory Reset Button";
64			linux,code = <KEY_RESTART>;
65			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
66		};
67	};
68
69	gpio_leds: gpio-leds {
70		compatible = "gpio-leds";
71		pinctrl-0 = <&gpio_leds_pins>;
72		pinctrl-names = "default";
73
74		led-power {
75			gpios = <&gpio1 23 GPIO_ACTIVE_HIGH>;
76			default-state = "on";
77		};
78
79		led-sata {
80			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
81			default-state = "off";
82			linux,default-trigger = "disk-activity";
83		};
84	};
85};
86
87&ahci0 {
88	status = "okay";
89};
90
91&bm {
92	status = "okay";
93};
94
95&bm_bppi {
96	status = "okay";
97};
98
99&eth0 {
100	status = "okay";
101	phy-mode = "rgmii-id";
102	buffer-manager = <&bm>;
103	bm,pool-long = <0>;
104	bm,pool-short = <1>;
105	fixed-link {
106		speed = <1000>;
107		full-duplex;
108	};
109};
110
111&eth2 {
112	status = "okay";
113	phy-mode = "sgmii";
114	buffer-manager = <&bm>;
115	bm,pool-long = <2>;
116	bm,pool-short = <3>;
117	fixed-link {
118		speed = <1000>;
119		full-duplex;
120	};
121};
122
123&i2c0 {
124	pinctrl-names = "default";
125	pinctrl-0 = <&i2c0_pins>;
126	status = "okay";
127
128	tmp421@4c {
129		compatible = "ti,tmp421";
130		reg = <0x4c>;
131	};
132
133	expander0: pca9635@68 {
134		#address-cells = <1>;
135		#size-cells = <0>;
136		compatible = "nxp,pca9635";
137		reg = <0x68>;
138	};
139};
140
141&nand_controller {
142	/* 128MiB or 256MiB */
143	status = "okay";
144	#address-cells = <1>;
145	#size-cells = <0>;
146
147	nand: nand@0 {
148		reg = <0>;
149		label = "pxa3xx_nand-0";
150		nand-rb = <0>;
151		nand-ecc-strength = <4>;
152		nand-ecc-step-size = <512>;
153		marvell,nand-keep-config;
154		nand-on-flash-bbt;
155	};
156};
157
158&mdio {
159	status = "okay";
160
161	ethernet-switch@0 {
162		compatible = "marvell,mv88e6085";
163		reg = <0>;
164
165		ethernet-ports {
166			#address-cells = <1>;
167			#size-cells = <0>;
168
169			ethernet-port@0 {
170				reg = <0>;
171				label = "lan4";
172			};
173
174			ethernet-port@1 {
175				reg = <1>;
176				label = "lan3";
177			};
178
179			ethernet-port@2 {
180				reg = <2>;
181				label = "lan2";
182			};
183
184			ethernet-port@3 {
185				reg = <3>;
186				label = "lan1";
187			};
188
189			ethernet-port@4 {
190				reg = <4>;
191				label = "wan";
192			};
193
194			ethernet-port@5 {
195				reg = <5>;
196				phy-mode = "sgmii";
197				ethernet = <&eth2>;
198
199				fixed-link {
200					speed = <1000>;
201					full-duplex;
202				};
203			};
204		};
205	};
206};
207
208&pciec {
209	status = "okay";
210};
211
212&pcie1 {
213	/* Marvell 88W8864, 5GHz-only */
214	status = "okay";
215};
216
217&pcie2 {
218	/* Marvell 88W8864, 2GHz-only */
219	status = "okay";
220};
221
222&pinctrl {
223	gpio_keys_pins: gpio-keys-pins {
224		/* mpp24: wps, mpp29: reset */
225		marvell,pins = "mpp24", "mpp29";
226		marvell,function = "gpio";
227	};
228
229	gpio_leds_pins: gpio-leds-pins {
230		/* mpp54: sata, mpp55: power */
231		marvell,pins = "mpp54", "mpp55";
232		marvell,function = "gpio";
233	};
234
235	usb3_1_vbus_pins: usb3_1-vbus-pins {
236		marvell,pins = "mpp50";
237		marvell,function = "gpio";
238	};
239};
240
241&spi0 {
242	status = "disabled";
243};
244
245&uart0 {
246	/* J10: VCC, NC, RX, NC, TX, GND  */
247	status = "okay";
248};
249
250&usb0 {
251	/* USB part of the eSATA/USB 2.0 port */
252	status = "okay";
253};
254
255&usb3_1 {
256	status = "okay";
257	usb-phy = <&usb3_1_phy>;
258};
259
260&rtc {
261	/* No crystal connected to the internal RTC */
262	status = "disabled";
263};
264