1// SPDX-License-Identifier: GPL-2.0 2/dts-v1/; 3#include "bcm2711.dtsi" 4#include "bcm2711-rpi.dtsi" 5#include "bcm283x-rpi-wifi-bt.dtsi" 6 7/ { 8 compatible = "raspberrypi,4-compute-module", "brcm,bcm2711"; 9 10 chosen { 11 /* 8250 auxiliary UART instead of pl011 */ 12 stdout-path = "serial1:115200n8"; 13 }; 14 15 sd_io_1v8_reg: regulator-sd-io-1v8 { 16 compatible = "regulator-gpio"; 17 regulator-name = "vdd-sd-io"; 18 regulator-min-microvolt = <1800000>; 19 regulator-max-microvolt = <3300000>; 20 regulator-boot-on; 21 regulator-always-on; 22 regulator-settling-time-us = <5000>; 23 gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>; 24 states = <1800000 0x1>, 25 <3300000 0x0>; 26 status = "okay"; 27 }; 28 29 sd_vcc_reg: regulator-sd-vcc { 30 compatible = "regulator-fixed"; 31 regulator-name = "vcc-sd"; 32 regulator-min-microvolt = <3300000>; 33 regulator-max-microvolt = <3300000>; 34 regulator-boot-on; 35 enable-active-high; 36 gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>; 37 }; 38}; 39 40&bt { 41 shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; 42}; 43 44/* EMMC2 is used to drive the eMMC */ 45&emmc2 { 46 bus-width = <8>; 47 vqmmc-supply = <&sd_io_1v8_reg>; 48 vmmc-supply = <&sd_vcc_reg>; 49 broken-cd; 50 /* Even the IP block is limited to 100 MHz 51 * this provides a throughput gain 52 */ 53 mmc-hs200-1_8v; 54 status = "okay"; 55}; 56 57&expgpio { 58 gpio-line-names = "BT_ON", 59 "WL_ON", 60 "PWR_LED_OFF", 61 "ANT1", 62 "VDD_SD_IO_SEL", 63 "CAM_GPIO", 64 "SD_PWR_ON", 65 "ANT2"; 66 67 ant1: ant1-hog { 68 gpio-hog; 69 gpios = <3 GPIO_ACTIVE_HIGH>; 70 /* internal antenna enabled */ 71 output-high; 72 line-name = "ant1"; 73 }; 74 75 ant2: ant2-hog { 76 gpio-hog; 77 gpios = <7 GPIO_ACTIVE_HIGH>; 78 /* external antenna disabled */ 79 output-low; 80 line-name = "ant2"; 81 }; 82}; 83 84&genet { 85 phy-handle = <&phy1>; 86 phy-mode = "rgmii-rxid"; 87 status = "okay"; 88}; 89 90&genet_mdio { 91 phy1: ethernet-phy@0 { 92 /* No PHY interrupt */ 93 reg = <0x0>; 94 }; 95}; 96 97/* uart0 communicates with the BT module */ 98&uart0 { 99 pinctrl-names = "default"; 100 pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>; 101 uart-has-rtscts; 102}; 103 104/* uart1 is mapped to the pin header */ 105&uart1 { 106 pinctrl-names = "default"; 107 pinctrl-0 = <&uart1_gpio14>; 108 status = "okay"; 109}; 110 111&wifi_pwrseq { 112 reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; 113}; 114