1MSM SoC HSUSB controllers 2 3EHCI 4 5Required properties: 6- compatible: Should contain "qcom,ehci-host" 7- regs: offset and length of the register set in the memory map 8- usb-phy: phandle for the PHY device 9 10Example EHCI controller device node: 11 12 ehci: ehci@f9a55000 { 13 compatible = "qcom,ehci-host"; 14 reg = <0xf9a55000 0x400>; 15 usb-phy = <&usb_otg>; 16 }; 17 18USB PHY with optional OTG: 19 20Required properties: 21- compatible: Should contain: 22 "qcom,usb-otg-ci" for chipsets with ChipIdea 45nm PHY 23 "qcom,usb-otg-snps" for chipsets with Synopsys 28nm PHY 24 25- regs: Offset and length of the register set in the memory map 26- interrupts: interrupt-specifier for the OTG interrupt. 27 28- clocks: A list of phandle + clock-specifier pairs for the 29 clocks listed in clock-names 30- clock-names: Should contain the following: 31 "phy" USB PHY reference clock 32 "core" Protocol engine clock 33 "iface" Interface bus clock 34 "alt_core" Protocol engine clock for targets with asynchronous 35 reset methodology. (optional) 36 37- vdccx-supply: phandle to the regulator for the vdd supply for 38 digital circuit operation. 39- v1p8-supply: phandle to the regulator for the 1.8V supply 40- v3p3-supply: phandle to the regulator for the 3.3V supply 41 42- resets: A list of phandle + reset-specifier pairs for the 43 resets listed in reset-names 44- reset-names: Should contain the following: 45 "phy" USB PHY controller reset 46 "link" USB LINK controller reset 47 48- qcom,otg-control: OTG control (VBUS and ID notifications) can be one of 49 1 - PHY control 50 2 - PMIC control 51 52Optional properties: 53- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" 54 55- switch-gpio: A phandle + gpio-specifier pair. Some boards are using Dual 56 SPDT USB Switch, witch is cotrolled by GPIO to de/multiplex 57 D+/D- USB lines between connectors. 58 59- qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device 60 Mode Eye Diagram test. Start address at which these values will be 61 written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as 62 "do not overwrite default value at this address". 63 For example: qcom,phy-init-sequence = < -1 0x63 >; 64 Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1. 65 66- qcom,phy-num: Select number of pyco-phy to use, can be one of 67 0 - PHY one, default 68 1 - Second PHY 69 Some platforms may have configuration to allow USB 70 controller work with any of the two HSPHYs present. 71 72- qcom,vdd-levels: This property must be a list of three integer values 73 (no, min, max) where each value represents either a voltage 74 in microvolts or a value corresponding to voltage corner. 75 76- qcom,manual-pullup: If present, vbus is not routed to USB controller/phy 77 and controller driver therefore enables pull-up explicitly 78 before starting controller using usbcmd run/stop bit. 79 80- extcon: phandles to external connector devices. First phandle 81 should point to external connector, which provide "USB" 82 cable events, the second should point to external connector 83 device, which provide "USB-HOST" cable events. If one of 84 the external connector devices is not required empty <0> 85 phandle should be specified. 86 87Example HSUSB OTG controller device node: 88 89 usb@f9a55000 { 90 compatible = "qcom,usb-otg-snps"; 91 reg = <0xf9a55000 0x400>; 92 interrupts = <0 134 0>; 93 dr_mode = "peripheral"; 94 95 clocks = <&gcc GCC_XO_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>, 96 <&gcc GCC_USB_HS_AHB_CLK>; 97 98 clock-names = "phy", "core", "iface"; 99 100 vddcx-supply = <&pm8841_s2_corner>; 101 v1p8-supply = <&pm8941_l6>; 102 v3p3-supply = <&pm8941_l24>; 103 104 resets = <&gcc GCC_USB2A_PHY_BCR>, <&gcc GCC_USB_HS_BCR>; 105 reset-names = "phy", "link"; 106 107 qcom,otg-control = <1>; 108 qcom,phy-init-sequence = < -1 0x63 >; 109 qcom,vdd-levels = <1 5 7>; 110 }; 111