1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 2# Copyright (c) 2020 MediaTek 3%YAML 1.2 4--- 5$id: http://devicetree.org/schemas/usb/mediatek,mtu3.yaml# 6$schema: http://devicetree.org/meta-schemas/core.yaml# 7 8title: MediaTek USB3 DRD Controller 9 10maintainers: 11 - Chunfeng Yun <chunfeng.yun@mediatek.com> 12 13allOf: 14 - $ref: usb-drd.yaml 15 16description: | 17 The DRD controller has a glue layer IPPC (IP Port Control), and its host is 18 based on xHCI. 19 20properties: 21 compatible: 22 items: 23 - enum: 24 - mediatek,mt2712-mtu3 25 - mediatek,mt8173-mtu3 26 - mediatek,mt8183-mtu3 27 - mediatek,mt8186-mtu3 28 - mediatek,mt8188-mtu3 29 - mediatek,mt8192-mtu3 30 - mediatek,mt8195-mtu3 31 - mediatek,mt8365-mtu3 32 - const: mediatek,mtu3 33 34 reg: 35 items: 36 - description: the registers of device MAC 37 - description: the registers of IP Port Control 38 39 reg-names: 40 items: 41 - const: mac 42 - const: ippc 43 44 interrupts: 45 description: 46 use "interrupts-extended" when the interrupts are connected to the 47 separate interrupt controllers 48 minItems: 1 49 items: 50 - description: SSUSB device controller interrupt 51 - description: optional, wakeup interrupt used to support runtime PM 52 53 interrupt-names: 54 items: 55 - const: device 56 - const: wakeup 57 58 power-domains: 59 description: A phandle to USB power domain node to control USB's MTCMOS 60 maxItems: 1 61 62 clocks: 63 minItems: 1 64 items: 65 - description: Controller clock used by normal mode 66 - description: Reference clock used by low power mode etc 67 - description: Mcu bus clock for register access 68 - description: DMA bus clock for data transfer 69 - description: DRD controller clock 70 - description: Frame count clock 71 72 clock-names: 73 minItems: 1 74 items: 75 - const: sys_ck # required, others are optional 76 - const: ref_ck 77 - const: mcu_ck 78 - const: dma_ck 79 - const: xhci_ck 80 - const: frmcnt_ck 81 82 phys: 83 description: 84 List of all the USB PHYs used, it's better to keep the sequence 85 as the hardware layout. 86 minItems: 1 87 items: 88 - description: USB2/HS PHY # required, others are optional 89 - description: USB3/SS(P) PHY 90 - description: USB2/HS PHY # the following for backward compatible 91 - description: USB3/SS(P) PHY 92 - description: USB2/HS PHY 93 - description: USB3/SS(P) PHY 94 - description: USB2/HS PHY 95 - description: USB3/SS(P) PHY 96 - description: USB2/HS PHY 97 98 vusb33-supply: 99 description: Regulator of USB AVDD3.3v 100 101 vbus-supply: 102 deprecated: true 103 description: | 104 Regulator of USB VBUS5v, needed when supports dual-role mode. 105 Particularly, if use an output GPIO to control a VBUS regulator, should 106 model it as a regulator. See bindings/regulator/fixed-regulator.yaml 107 It's considered valid for compatibility reasons, not allowed for 108 new bindings, and put into a usb-connector node. 109 110 dr_mode: 111 enum: [host, peripheral, otg] 112 default: otg 113 114 maximum-speed: 115 enum: [super-speed-plus, super-speed, high-speed, full-speed] 116 117 resets: 118 maxItems: 1 119 120 "#address-cells": 121 enum: [1, 2] 122 123 "#size-cells": 124 enum: [1, 2] 125 126 ranges: true 127 128 extcon: 129 deprecated: true 130 description: | 131 Phandle to the extcon device detecting the IDDIG state, needed 132 when supports dual-role mode. 133 It's considered valid for compatibility reasons, not allowed for 134 new bindings, and use "usb-role-switch" property instead. 135 136 usb-role-switch: 137 $ref: /schemas/types.yaml#/definitions/flag 138 description: Support role switch. 139 type: boolean 140 141 role-switch-default-mode: 142 enum: [host, peripheral] 143 default: host 144 145 connector: 146 $ref: /schemas/connector/usb-connector.yaml# 147 description: 148 Connector for dual role switch, especially for "gpio-usb-b-connector" 149 type: object 150 151 port: 152 description: 153 Any connector to the data bus of this controller should be modelled 154 using the OF graph bindings specified, if the "usb-role-switch" 155 property is used. See graph.txt 156 $ref: /schemas/graph.yaml#/properties/port 157 158 enable-manual-drd: 159 $ref: /schemas/types.yaml#/definitions/flag 160 description: 161 supports manual dual-role switch via debugfs; usually used when 162 receptacle is TYPE-A and also wants to support dual-role mode. 163 type: boolean 164 165 wakeup-source: 166 description: enable USB remote wakeup, see power/wakeup-source.txt 167 type: boolean 168 169 mediatek,syscon-wakeup: 170 $ref: /schemas/types.yaml#/definitions/phandle-array 171 maxItems: 1 172 description: 173 A phandle to syscon used to access the register of the USB wakeup glue 174 layer between xHCI and SPM, the field should always be 3 cells long. 175 items: 176 items: 177 - description: 178 The first cell represents a phandle to syscon 179 - description: 180 The second cell represents the register base address of the glue 181 layer in syscon 182 - description: | 183 The third cell represents the hardware version of the glue layer, 184 1 - used by mt8173 etc, revision 1 without following IPM rule; 185 2 - used by mt2712 etc, revision 2 with following IPM rule; 186 101 - used by mt8183, specific 1.01; 187 102 - used by mt8192, specific 1.02; 188 enum: [1, 2, 101, 102] 189 190 mediatek,u3p-dis-msk: 191 $ref: /schemas/types.yaml#/definitions/uint32 192 description: The mask to disable u3ports, bit0 for u3port0, 193 bit1 for u3port1, ... etc 194 195 mediatek,u2p-dis-msk: 196 $ref: /schemas/types.yaml#/definitions/uint32 197 description: The mask to disable u2ports, bit0 for u2port0, 198 bit1 for u2port1, ... etc; but can't disable u2port0 if dual role mode 199 is enabled, so will be skipped in this case. 200 201# Required child node when support dual-role 202patternProperties: 203 "^usb@[0-9a-f]+$": 204 type: object 205 $ref: /schemas/usb/mediatek,mtk-xhci.yaml# 206 description: 207 The xhci should be added as subnode to mtu3 as shown in the following 208 example if the host mode is enabled. 209 210dependencies: 211 connector: [ usb-role-switch ] 212 port: [ usb-role-switch ] 213 role-switch-default-mode: [ usb-role-switch ] 214 wakeup-source: [ 'mediatek,syscon-wakeup' ] 215 216required: 217 - compatible 218 - reg 219 - reg-names 220 - interrupts 221 - clocks 222 - clock-names 223 224additionalProperties: false 225 226examples: 227 # Dual role switch by extcon 228 - | 229 #include <dt-bindings/clock/mt8173-clk.h> 230 #include <dt-bindings/interrupt-controller/arm-gic.h> 231 #include <dt-bindings/interrupt-controller/irq.h> 232 #include <dt-bindings/phy/phy.h> 233 #include <dt-bindings/power/mt8173-power.h> 234 235 usb@11271000 { 236 compatible = "mediatek,mt8173-mtu3", "mediatek,mtu3"; 237 reg = <0x11271000 0x3000>, <0x11280700 0x0100>; 238 reg-names = "mac", "ippc"; 239 interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>; 240 phys = <&phy_port0 PHY_TYPE_USB3>, <&phy_port1 PHY_TYPE_USB2>; 241 power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; 242 clocks = <&topckgen CLK_TOP_USB30_SEL>; 243 clock-names = "sys_ck"; 244 vusb33-supply = <&mt6397_vusb_reg>; 245 vbus-supply = <&usb_p0_vbus>; 246 extcon = <&extcon_usb>; 247 dr_mode = "otg"; 248 wakeup-source; 249 mediatek,syscon-wakeup = <&pericfg 0x400 1>; 250 #address-cells = <1>; 251 #size-cells = <1>; 252 ranges; 253 254 xhci: usb@11270000 { 255 compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci"; 256 reg = <0x11270000 0x1000>; 257 reg-names = "mac"; 258 interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; 259 power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; 260 clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; 261 clock-names = "sys_ck", "ref_ck"; 262 vusb33-supply = <&mt6397_vusb_reg>; 263 }; 264 }; 265 266 # Dual role switch by gpio-usb-b-connector 267 - | 268 #include <dt-bindings/gpio/gpio.h> 269 #include <dt-bindings/power/mt2712-power.h> 270 271 usb@112c1000 { 272 compatible = "mediatek,mt2712-mtu3", "mediatek,mtu3"; 273 reg = <0x112c1000 0x3000>, <0x112d0700 0x0100>; 274 reg-names = "mac", "ippc"; 275 interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_LOW>; 276 phys = <&u2port2 PHY_TYPE_USB2>; 277 power-domains = <&scpsys MT2712_POWER_DOMAIN_USB2>; 278 clocks = <&topckgen CLK_TOP_USB30_SEL>; 279 clock-names = "sys_ck"; 280 dr_mode = "otg"; 281 usb-role-switch; 282 #address-cells = <1>; 283 #size-cells = <1>; 284 ranges; 285 286 host0: usb@11270000 { 287 compatible = "mediatek,mt2712-xhci", "mediatek,mtk-xhci"; 288 reg = <0x11270000 0x1000>; 289 reg-names = "mac"; 290 interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_LOW>; 291 power-domains = <&scpsys MT2712_POWER_DOMAIN_USB>; 292 clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; 293 clock-names = "sys_ck", "ref_ck"; 294 }; 295 296 connector { 297 compatible = "gpio-usb-b-connector", "usb-b-connector"; 298 type = "micro"; 299 id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>; 300 vbus-supply = <&usb_p0_vbus>; 301 }; 302 }; 303 304 # Dual role switch with type-c 305 - | 306 usb@11201000 { 307 compatible ="mediatek,mt8183-mtu3", "mediatek,mtu3"; 308 reg = <0x11201000 0x2e00>, <0x11203e00 0x0100>; 309 reg-names = "mac", "ippc"; 310 interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_LOW>; 311 phys = <&u2port0 PHY_TYPE_USB2>; 312 clocks = <&clk26m>; 313 clock-names = "sys_ck"; 314 mediatek,syscon-wakeup = <&pericfg 0x400 1>; 315 wakeup-source; 316 dr_mode = "otg"; 317 usb-role-switch; 318 role-switch-default-mode = "host"; 319 #address-cells = <1>; 320 #size-cells = <1>; 321 ranges; 322 323 host: usb@11200000 { 324 compatible = "mediatek,mt8183-xhci", "mediatek,mtk-xhci"; 325 reg = <0x11200000 0x1000>; 326 reg-names = "mac"; 327 interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_LOW>; 328 clocks = <&clk26m>; 329 clock-names = "sys_ck"; 330 }; 331 332 port { 333 usb_role_sw: endpoint { 334 remote-endpoint = <&hs_ep>; 335 }; 336 }; 337 }; 338 339... 340