1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 2# Copyright (c) 2020 MediaTek 3%YAML 1.2 4--- 5$id: http://devicetree.org/schemas/usb/mediatek,mtk-xhci.yaml# 6$schema: http://devicetree.org/meta-schemas/core.yaml# 7 8title: MediaTek USB3 xHCI 9 10maintainers: 11 - Chunfeng Yun <chunfeng.yun@mediatek.com> 12 13allOf: 14 - $ref: "usb-xhci.yaml" 15 16description: | 17 There are two scenarios: 18 case 1: only supports xHCI driver; 19 case 2: supports dual-role mode, and the host is based on xHCI driver. 20 21properties: 22 # common properties for both case 1 and case 2 23 compatible: 24 items: 25 - enum: 26 - mediatek,mt2701-xhci 27 - mediatek,mt2712-xhci 28 - mediatek,mt7622-xhci 29 - mediatek,mt7623-xhci 30 - mediatek,mt7629-xhci 31 - mediatek,mt8173-xhci 32 - mediatek,mt8183-xhci 33 - mediatek,mt8186-xhci 34 - mediatek,mt8188-xhci 35 - mediatek,mt8192-xhci 36 - mediatek,mt8195-xhci 37 - const: mediatek,mtk-xhci 38 39 reg: 40 minItems: 1 41 items: 42 - description: the registers of xHCI MAC 43 - description: the registers of IP Port Control 44 45 reg-names: 46 minItems: 1 47 items: 48 - const: mac 49 - const: ippc # optional, only needed for case 1. 50 51 interrupts: 52 description: 53 use "interrupts-extended" when the interrupts are connected to the 54 separate interrupt controllers 55 minItems: 1 56 items: 57 - description: xHCI host controller interrupt 58 - description: optional, wakeup interrupt used to support runtime PM 59 60 interrupt-names: 61 minItems: 1 62 items: 63 - const: host 64 - const: wakeup 65 66 power-domains: 67 description: A phandle to USB power domain node to control USB's MTCMOS 68 maxItems: 1 69 70 clocks: 71 minItems: 1 72 items: 73 - description: Controller clock used by normal mode 74 - description: Reference clock used by low power mode etc 75 - description: Mcu bus clock for register access 76 - description: DMA bus clock for data transfer 77 - description: controller clock 78 79 clock-names: 80 minItems: 1 81 items: 82 - const: sys_ck # required, the following ones are optional 83 - const: ref_ck 84 - const: mcu_ck 85 - const: dma_ck 86 - const: xhci_ck 87 88 assigned-clocks: 89 minItems: 1 90 maxItems: 5 91 92 assigned-clock-parents: 93 minItems: 1 94 maxItems: 5 95 96 phys: 97 description: 98 List of all PHYs used on this HCD, it's better to keep PHYs in order 99 as the hardware layout 100 minItems: 1 101 items: 102 - description: USB2/HS PHY # required, others are optional 103 - description: USB3/SS(P) PHY 104 - description: USB2/HS PHY 105 - description: USB3/SS(P) PHY 106 - description: USB2/HS PHY 107 - description: USB3/SS(P) PHY 108 - description: USB2/HS PHY 109 - description: USB3/SS(P) PHY 110 - description: USB2/HS PHY 111 112 vusb33-supply: 113 description: Regulator of USB AVDD3.3v 114 115 vbus-supply: 116 description: Regulator of USB VBUS5v 117 118 resets: 119 maxItems: 1 120 121 usb3-lpm-capable: true 122 123 usb2-lpm-disable: true 124 125 imod-interval-ns: 126 description: 127 Interrupt moderation interval value, it is 8 times as much as that 128 defined in the xHCI spec on MTK's controller. 129 default: 5000 130 131 # the following properties are only used for case 1 132 wakeup-source: 133 description: enable USB remote wakeup, see power/wakeup-source.txt 134 type: boolean 135 136 mediatek,syscon-wakeup: 137 $ref: /schemas/types.yaml#/definitions/phandle-array 138 maxItems: 1 139 description: 140 A phandle to syscon used to access the register of the USB wakeup glue 141 layer between xHCI and SPM, the field should always be 3 cells long. 142 items: 143 items: 144 - description: 145 The first cell represents a phandle to syscon 146 - description: 147 The second cell represents the register base address of the glue 148 layer in syscon 149 - description: | 150 The third cell represents the hardware version of the glue layer, 151 1 - used by mt8173 etc, revision 1 without following IPM rule; 152 2 - used by mt2712 etc, revision 2 following IPM rule; 153 101 - used by mt8183, specific 1.01; 154 102 - used by mt8192, specific 1.02; 155 103 - used by mt8195, IP0, specific 1.03; 156 104 - used by mt8195, IP1, specific 1.04; 157 105 - used by mt8195, IP2, specific 1.05; 158 106 - used by mt8195, IP3, specific 1.06; 159 enum: [1, 2, 101, 102, 103, 104, 105, 106] 160 161 mediatek,u3p-dis-msk: 162 $ref: /schemas/types.yaml#/definitions/uint32 163 description: The mask to disable u3ports, bit0 for u3port0, 164 bit1 for u3port1, ... etc 165 166 mediatek,u2p-dis-msk: 167 $ref: /schemas/types.yaml#/definitions/uint32 168 description: The mask to disable u2ports, bit0 for u2port0, 169 bit1 for u2port1, ... etc 170 171 "#address-cells": 172 const: 1 173 174 "#size-cells": 175 const: 0 176 177patternProperties: 178 "@[0-9a-f]{1}$": 179 type: object 180 description: The hard wired USB devices. 181 182dependencies: 183 wakeup-source: [ 'mediatek,syscon-wakeup' ] 184 185required: 186 - compatible 187 - reg 188 - reg-names 189 - interrupts 190 - clocks 191 - clock-names 192 193additionalProperties: false 194 195examples: 196 - | 197 #include <dt-bindings/clock/mt8173-clk.h> 198 #include <dt-bindings/interrupt-controller/arm-gic.h> 199 #include <dt-bindings/interrupt-controller/irq.h> 200 #include <dt-bindings/phy/phy.h> 201 #include <dt-bindings/power/mt8173-power.h> 202 203 usb@11270000 { 204 compatible = "mediatek,mt8173-xhci", "mediatek,mtk-xhci"; 205 reg = <0x11270000 0x1000>, <0x11280700 0x0100>; 206 reg-names = "mac", "ippc"; 207 interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; 208 power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; 209 clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; 210 clock-names = "sys_ck", "ref_ck"; 211 phys = <&u3port0 PHY_TYPE_USB3>, <&u2port1 PHY_TYPE_USB2>; 212 vusb33-supply = <&mt6397_vusb_reg>; 213 vbus-supply = <&usb_p1_vbus>; 214 imod-interval-ns = <10000>; 215 mediatek,syscon-wakeup = <&pericfg 0x400 1>; 216 wakeup-source; 217 usb3-lpm-capable; 218 }; 219... 220