1CS35L35 Boosted Speaker Amplifier 2 3Required properties: 4 5 - compatible : "cirrus,cs35l35" 6 7 - reg : the I2C address of the device for I2C 8 9 - VA-supply, VP-supply : power supplies for the device, 10 as covered in 11 Documentation/devicetree/bindings/regulator/regulator.txt. 12 13 - interrupts : IRQ line info CS35L35. 14 (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt 15 for further information relating to interrupt properties) 16 17 - cirrus,boost-ind-nanohenry: Inductor value for boost converter. The value is 18 in nH and they can be values of 1000nH, 1200nH, 1500nH, and 2200nH. 19 20Optional properties: 21 - reset-gpios : gpio used to reset the amplifier 22 23 - cirrus,stereo-config : Boolean to determine if there are 2 AMPs for a 24 Stereo configuration 25 26 - cirrus,audio-channel : Set Location of Audio Signal on Serial Port 27 0 = Data Packet received on Left I2S Channel 28 1 = Data Packet received on Right I2S Channel 29 30 - cirrus,advisory-channel : Set Location of Advisory Signal on Serial Port 31 0 = Data Packet received on Left I2S Channel 32 1 = Data Packet received on Right I2S Channel 33 34 - cirrus,shared-boost : Boolean to enable ClassH tracking of Advisory Signal 35 if 2 Devices share Boost BST_CTL 36 37 - cirrus,external-boost : Boolean to specify the device is using an external 38 boost supply, note that sharing a boost from another cs35l35 would constitute 39 using an external supply for the slave device 40 41 - cirrus,sp-drv-strength : Value for setting the Serial Port drive strength 42 Table 3-10 of the datasheet lists drive-strength specifications 43 0 = 1x (Default) 44 1 = .5x 45 - cirrus,sp-drv-unused : Determines how unused slots should be driven on the 46 Serial Port. 47 0 - Hi-Z 48 2 - Drive 0's (Default) 49 3 - Drive 1's 50 51 - cirrus,bst-pdn-fet-on : Boolean to determine if the Boost PDN control 52 powers down with a rectification FET On or Off. If VSPK is supplied 53 externally then FET is off. 54 55 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost 56 converter's output voltage in mV. The range is from 2600mV to 9000mV with 57 increments of 100mV. 58 (Default) VP 59 60 - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA. 61 Configures the peak current by monitoring the current through the boost FET. 62 Range starts at 1680mA and goes to a maximum of 4480mA with increments of 63 110mA. 64 (Default) 2.46 Amps 65 66 - cirrus,amp-gain-zc : Boolean to determine if to use Amplifier gain-change 67 zero-cross 68 69Optional H/G Algorithm sub-node: 70 71 The cs35l35 node can have a single "cirrus,classh-internal-algo" sub-node 72 that will disable automatic control of the internal H/G Algorithm. 73 74 It is strongly recommended that the Datasheet be referenced when adjusting 75 or using these Class H Algorithm controls over the internal Algorithm. 76 Serious damage can occur to the Device and surrounding components. 77 78 - cirrus,classh-internal-algo : Sub-node for the Internal Class H Algorithm 79 See Section 4.3 Internal Class H Algorithm in the Datasheet. 80 If not used, the device manages the ClassH Algorithm internally. 81 82Optional properties for the "cirrus,classh-internal-algo" Sub-node 83 84 Section 7.29 Class H Control 85 - cirrus,classh-bst-overide : Boolean 86 - cirrus,classh-bst-max-limit 87 - cirrus,classh-mem-depth 88 89 Section 7.30 Class H Headroom Control 90 - cirrus,classh-headroom 91 92 Section 7.31 Class H Release Rate 93 - cirrus,classh-release-rate 94 95 Section 7.32 Class H Weak FET Drive Control 96 - cirrus,classh-wk-fet-disable 97 - cirrus,classh-wk-fet-delay 98 - cirrus,classh-wk-fet-thld 99 100 Section 7.34 Class H VP Control 101 - cirrus,classh-vpch-auto 102 - cirrus,classh-vpch-rate 103 - cirrus,classh-vpch-man 104 105Optional Monitor Signal Format sub-node: 106 107 The cs35l35 node can have a single "cirrus,monitor-signal-format" sub-node 108 for adjusting the Depth, Location and Frame of the Monitoring Signals 109 for Algorithms. 110 111 See Sections 4.8.2 through 4.8.4 Serial-Port Control in the Datasheet 112 113 -cirrus,monitor-signal-format : Sub-node for the Monitor Signaling Formatting 114 on the I2S Port. Each of the 3 8 bit values in the array contain the settings 115 for depth, location, and frame. 116 117 If not used, the defaults for the 6 monitor signals is used. 118 119 Sections 7.44 - 7.53 lists values for the depth, location, and frame 120 for each monitoring signal. 121 122 - cirrus,imon : 4 8 bit values to set the depth, location, frame and ADC 123 scale of the IMON monitor signal. 124 125 - cirrus,vmon : 3 8 bit values to set the depth, location, and frame 126 of the VMON monitor signal. 127 128 - cirrus,vpmon : 3 8 bit values to set the depth, location, and frame 129 of the VPMON monitor signal. 130 131 - cirrus,vbstmon : 3 8 bit values to set the depth, location, and frame 132 of the VBSTMON monitor signal 133 134 - cirrus,vpbrstat : 3 8 bit values to set the depth, location, and frame 135 of the VPBRSTAT monitor signal 136 137 - cirrus,zerofill : 3 8 bit values to set the depth, location, and frame\ 138 of the ZEROFILL packet in the monitor signal 139 140Example: 141 142cs35l35: cs35l35@20 { 143 compatible = "cirrus,cs35l35"; 144 reg = <0x20>; 145 VA-supply = <&dummy_vreg>; 146 VP-supply = <&dummy_vreg>; 147 reset-gpios = <&axi_gpio 54 0>; 148 interrupt-parent = <&gpio8>; 149 interrupts = <3 IRQ_TYPE_LEVEL_LOW>; 150 cirrus,boost-ctl-millivolt = <9000>; 151 152 cirrus,stereo-config; 153 cirrus,audio-channel = <0x00>; 154 cirrus,advisory-channel = <0x01>; 155 cirrus,shared-boost; 156 157 cirrus,classh-internal-algo { 158 cirrus,classh-bst-overide; 159 cirrus,classh-bst-max-limit = <0x01>; 160 cirrus,classh-mem-depth = <0x01>; 161 cirrus,classh-release-rate = <0x08>; 162 cirrus,classh-headroom-millivolt = <0x0B>; 163 cirrus,classh-wk-fet-disable = <0x01>; 164 cirrus,classh-wk-fet-delay = <0x04>; 165 cirrus,classh-wk-fet-thld = <0x01>; 166 cirrus,classh-vpch-auto = <0x01>; 167 cirrus,classh-vpch-rate = <0x02>; 168 cirrus,classh-vpch-man = <0x05>; 169 }; 170 171 /* Depth, Location, Frame */ 172 cirrus,monitor-signal-format { 173 cirrus,imon = /bits/ 8 <0x03 0x00 0x01>; 174 cirrus,vmon = /bits/ 8 <0x03 0x00 0x00>; 175 cirrus,vpmon = /bits/ 8 <0x03 0x04 0x00>; 176 cirrus,vbstmon = /bits/ 8 <0x03 0x04 0x01>; 177 cirrus,vpbrstat = /bits/ 8 <0x00 0x04 0x00>; 178 cirrus,zerofill = /bits/ 8 <0x00 0x00 0x00>; 179 }; 180 181}; 182