1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 2%YAML 1.2 3--- 4$id: http://devicetree.org/schemas/pinctrl/qcom,mdm9607-pinctrl.yaml# 5$schema: http://devicetree.org/meta-schemas/core.yaml# 6 7title: Qualcomm Technologies, Inc. MDM9607 TLMM block 8 9maintainers: 10 - Konrad Dybcio <konrad.dybcio@somainline.org> 11 12description: | 13 This binding describes the Top Level Mode Multiplexer block found in the 14 MDM9607 platform. 15 16allOf: 17 - $ref: "pinctrl.yaml#" 18 - $ref: /schemas/pinctrl/qcom,tlmm-common.yaml# 19 20properties: 21 compatible: 22 const: qcom,mdm9607-tlmm 23 24 reg: 25 maxItems: 1 26 27 interrupts: true 28 interrupt-controller: true 29 '#interrupt-cells': true 30 gpio-controller: true 31 gpio-reserved-ranges: true 32 '#gpio-cells': true 33 gpio-ranges: true 34 wakeup-parent: true 35 36required: 37 - compatible 38 - reg 39 40additionalProperties: false 41 42patternProperties: 43 '-state$': 44 oneOf: 45 - $ref: "#/$defs/qcom-mdm9607-tlmm-state" 46 - patternProperties: 47 ".*": 48 $ref: "#/$defs/qcom-mdm9607-tlmm-state" 49 50'$defs': 51 qcom-mdm9607-tlmm-state: 52 type: object 53 description: 54 Pinctrl node's client devices use subnodes for desired pin configuration. 55 Client device subnodes use below standard properties. 56 $ref: "qcom,tlmm-common.yaml#/$defs/qcom-tlmm-state" 57 58 properties: 59 pins: 60 description: 61 List of gpio pins affected by the properties specified in this 62 subnode. 63 items: 64 oneOf: 65 - pattern: "^gpio([1-9]|[1-7][0-9]|80)$" 66 - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc2_clk, sdc2_cmd, 67 sdc2_data, qdsd_cmd, qdsd_data0, qdsd_data1, qdsd_data2, 68 qdsd_data3 ] 69 minItems: 1 70 maxItems: 16 71 72 function: 73 description: 74 Specify the alternative function to be configured for the specified 75 pins. 76 77 enum: [ adsp_ext, atest_bbrx0, atest_bbrx1, atest_char, atest_char0, 78 atest_char1, atest_char2, atest_char3, 79 atest_combodac_to_gpio_native, atest_gpsadc_dtest0_native, 80 atest_gpsadc_dtest1_native, atest_tsens, backlight_en_b, 81 bimc_dte0, bimc_dte1, blsp1_spi, blsp2_spi, blsp3_spi, 82 blsp_i2c1, blsp_i2c2, blsp_i2c3, blsp_i2c4, blsp_i2c5, 83 blsp_i2c6, blsp_spi1, blsp_spi2, blsp_spi3, blsp_spi4, 84 blsp_spi5, blsp_spi6, blsp_uart1, blsp_uart2, blsp_uart3, 85 blsp_uart4, blsp_uart5, blsp_uart6, blsp_uim1, blsp_uim2, 86 codec_int, codec_rst, coex_uart, cri_trng, cri_trng0, 87 cri_trng1, dbg_out, ebi0_wrcdc, ebi2_a, ebi2_a_d_8_b, 88 ebi2_lcd, ebi2_lcd_cs_n_b, ebi2_lcd_te_b, eth_irq, eth_rst, 89 gcc_gp1_clk_a, gcc_gp1_clk_b, gcc_gp2_clk_a, gcc_gp2_clk_b, 90 gcc_gp3_clk_a, gcc_gp3_clk_b, gcc_plltest, gcc_tlmm, gmac_mdio, 91 gpio, gsm0_tx, lcd_rst, ldo_en, ldo_update, m_voc, modem_tsync, 92 nav_ptp_pps_in_a, nav_ptp_pps_in_b, nav_tsync_out_a, 93 nav_tsync_out_b, pa_indicator, pbs0, pbs1, pbs2, 94 pri_mi2s_data0_a, pri_mi2s_data1_a, pri_mi2s_mclk_a, 95 pri_mi2s_sck_a, pri_mi2s_ws_a, prng_rosc, ptp_pps_out_a, 96 ptp_pps_out_b, pwr_crypto_enabled_a, pwr_crypto_enabled_b, 97 pwr_modem_enabled_a, pwr_modem_enabled_b, pwr_nav_enabled_a, 98 pwr_nav_enabled_b, qdss_cti_trig_in_a0, qdss_cti_trig_in_a1, 99 qdss_cti_trig_in_b0, qdss_cti_trig_in_b1, qdss_cti_trig_out_a0, 100 qdss_cti_trig_out_a1, qdss_cti_trig_out_b0, qdss_cti_trig_out_b1, 101 qdss_traceclk_a, qdss_traceclk_b, qdss_tracectl_a, 102 qdss_tracectl_b, qdss_tracedata_a, qdss_tracedata_b, rcm_marker1, 103 rcm_marker2, sd_write, sec_mi2s, sensor_en, sensor_int2, 104 sensor_int3, sensor_rst, ssbi1, ssbi2, touch_rst, ts_int, 105 uim1_clk, uim1_data, uim1_present, uim1_reset, uim2_clk, 106 uim2_data, uim2_present, uim2_reset, uim_batt, wlan_en1, ] 107 108 bias-disable: true 109 bias-pull-down: true 110 bias-pull-up: true 111 drive-strength: true 112 input-enable: true 113 output-high: true 114 output-low: true 115 116 required: 117 - pins 118 - function 119 120 additionalProperties: false 121 122examples: 123 - | 124 #include <dt-bindings/interrupt-controller/arm-gic.h> 125 tlmm: pinctrl@1000000 { 126 compatible = "qcom,mdm9607-tlmm"; 127 reg = <0x01000000 0x300000>; 128 interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; 129 gpio-controller; 130 gpio-ranges = <&msmgpio 0 0 80>; 131 #gpio-cells = <2>; 132 interrupt-controller; 133 #interrupt-cells = <2>; 134 }; 135