1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) 2%YAML 1.2 3--- 4$id: http://devicetree.org/schemas/pinctrl/mediatek,mt7622-pinctrl.yaml# 5$schema: http://devicetree.org/meta-schemas/core.yaml# 6 7title: Mediatek MT7622 Pin Controller 8 9maintainers: 10 - Sean Wang <sean.wang@kernel.org> 11 12description: |+ 13 The MediaTek's MT7622 Pin controller is used to control SoC pins. 14 15properties: 16 compatible: 17 enum: 18 - mediatek,mt7622-pinctrl 19 - mediatek,mt7629-pinctrl 20 21 reg: 22 maxItems: 1 23 24 reg-names: 25 items: 26 - const: eint 27 28 gpio-controller: true 29 30 "#gpio-cells": 31 const: 2 32 description: | 33 Number of cells in GPIO specifier. Since the generic GPIO 34 binding is used, the amount of cells must be specified as 2. See the below 35 mentioned gpio binding representation for description of particular cells. 36 37 interrupt-controller: true 38 39 interrupts: 40 maxItems: 1 41 42 "#interrupt-cells": 43 const: 2 44 45allOf: 46 - $ref: "pinctrl.yaml#" 47 48required: 49 - compatible 50 - reg 51 - gpio-controller 52 - "#gpio-cells" 53 54if: 55 required: 56 - interrupt-controller 57then: 58 required: 59 - reg-names 60 - interrupts 61 - "#interrupt-cells" 62 63patternProperties: 64 '-pins(-[a-z]+)?$': 65 type: object 66 additionalProperties: false 67 patternProperties: 68 '^mux(-|$)': 69 type: object 70 additionalProperties: false 71 description: | 72 pinmux configuration nodes. 73 $ref: "/schemas/pinctrl/pinmux-node.yaml" 74 properties: 75 function: 76 description: | 77 A string containing the name of the function to mux to the group. 78 enum: [emmc, eth, i2c, i2s, ir, led, flash, pcie, pmic, pwm, sd, 79 spi, tdm, uart, watchdog, wifi] 80 81 groups: 82 description: | 83 An array of strings. Each string contains the name of a group. 84 85 drive-strength: 86 enum: [4, 8, 12, 16] 87 88 required: 89 - groups 90 - function 91 92 allOf: 93 - if: 94 properties: 95 function: 96 const: emmc 97 then: 98 properties: 99 groups: 100 enum: [emmc, emmc_rst] 101 - if: 102 properties: 103 function: 104 const: eth 105 then: 106 properties: 107 groups: 108 enum: [esw, esw_p0_p1, esw_p2_p3_p4, rgmii_via_esw, 109 rgmii_via_gmac1, rgmii_via_gmac2, mdc_mdio] 110 - if: 111 properties: 112 function: 113 const: i2c 114 then: 115 properties: 116 groups: 117 enum: [i2c0, i2c_0, i2c_1, i2c1_0, i2c1_1, i2c1_2, i2c2_0, 118 i2c2_1, i2c2_2] 119 - if: 120 properties: 121 function: 122 const: i2s 123 then: 124 properties: 125 groups: 126 enum: [i2s_in_mclk_bclk_ws, i2s1_in_data, i2s2_in_data, 127 i2s3_in_data, i2s4_in_data, i2s_out_mclk_bclk_ws, 128 i2s1_out_data, i2s2_out_data, i2s3_out_data, 129 i2s4_out_data] 130 - if: 131 properties: 132 function: 133 const: ir 134 then: 135 properties: 136 groups: 137 enum: [ir_0_tx, ir_1_tx, ir_2_tx, ir_0_rx, ir_1_rx, ir_2_rx] 138 - if: 139 properties: 140 function: 141 const: led 142 then: 143 properties: 144 groups: 145 enum: [ephy_leds, ephy0_led, ephy1_led, ephy2_led, ephy3_led, 146 ephy4_led, wled, wf2g_led, wf5g_led] 147 - if: 148 properties: 149 function: 150 const: flash 151 then: 152 properties: 153 groups: 154 enum: [par_nand, snfi, spi_nor] 155 - if: 156 properties: 157 function: 158 const: pcie 159 then: 160 properties: 161 groups: 162 enum: [pcie0_0_waken, pcie0_1_waken, pcie1_0_waken, 163 pcie0_0_clkreq, pcie0_1_clkreq, pcie1_0_clkreq, 164 pcie0_pad_perst, pcie1_pad_perst, pcie_pereset, 165 pcie_wake, pcie_clkreq] 166 - if: 167 properties: 168 function: 169 const: pmic 170 then: 171 properties: 172 groups: 173 enum: [pmic_bus] 174 - if: 175 properties: 176 function: 177 const: pwm 178 then: 179 properties: 180 groups: 181 enum: [pwm_ch1_0, pwm_ch1_1, pwm_ch1_2, pwm_ch2_0, pwm_ch2_1, 182 pwm_ch2_2, pwm_ch3_0, pwm_ch3_1, pwm_ch3_2, pwm_ch4_0, 183 pwm_ch4_1, pwm_ch4_2, pwm_ch4_3, pwm_ch5_0, pwm_ch5_1, 184 pwm_ch5_2, pwm_ch6_0, pwm_ch6_1, pwm_ch6_2, pwm_ch6_3, 185 pwm_ch7_0, pwm_0, pwm_1] 186 - if: 187 properties: 188 function: 189 const: sd 190 then: 191 properties: 192 groups: 193 enum: [sd_0, sd_1] 194 - if: 195 properties: 196 function: 197 const: spi 198 then: 199 properties: 200 groups: 201 enum: [spic0_0, spic0_1, spic1_0, spic1_1, spic2_0_wp_hold, 202 spic2_0, spi_0, spi_1, spi_wp, spi_hold] 203 - if: 204 properties: 205 function: 206 const: tdm 207 then: 208 properties: 209 groups: 210 enum: [tdm_0_out_mclk_bclk_ws, tdm_0_in_mclk_bclk_ws, 211 tdm_0_out_data, tdm_0_in_data, tdm_1_out_mclk_bclk_ws, 212 tdm_1_in_mclk_bclk_ws, tdm_1_out_data, tdm_1_in_data] 213 - if: 214 properties: 215 function: 216 const: uart 217 then: 218 properties: 219 groups: 220 enum: [uart0_0_tx_rx, uart1_0_tx_rx, uart1_0_rts_cts, 221 uart1_1_tx_rx, uart1_1_rts_cts, uart2_0_tx_rx, 222 uart2_0_rts_cts, uart2_1_tx_rx, uart2_1_rts_cts, 223 uart2_2_tx_rx, uart2_2_rts_cts, uart2_3_tx_rx, 224 uart3_0_tx_rx, uart3_1_tx_rx, uart3_1_rts_cts, 225 uart4_0_tx_rx, uart4_1_tx_rx, uart4_1_rts_cts, 226 uart4_2_tx_rx, uart4_2_rts_cts, uart0_txd_rxd, 227 uart1_0_txd_rxd, uart1_0_cts_rts, uart1_1_txd_rxd, 228 uart1_1_cts_rts, uart2_0_txd_rxd, uart2_0_cts_rts, 229 uart2_1_txd_rxd, uart2_1_cts_rts] 230 - if: 231 properties: 232 function: 233 const: watchdog 234 then: 235 properties: 236 groups: 237 enum: [watchdog] 238 - if: 239 properties: 240 function: 241 const: wifi 242 then: 243 properties: 244 groups: 245 enum: [wf0_2g, wf0_5g] 246 247 '^conf(-|$)': 248 type: object 249 additionalProperties: false 250 description: | 251 pinconf configuration nodes. 252 $ref: "/schemas/pinctrl/pincfg-node.yaml" 253 254 properties: 255 groups: 256 description: | 257 An array of strings. Each string contains the name of a group. 258 Valid values are the same as the pinmux node. 259 260 pins: 261 description: | 262 An array of strings. Each string contains the name of a pin. 263 enum: [GPIO_A, I2S1_IN, I2S1_OUT, I2S_BCLK, I2S_WS, I2S_MCLK, TXD0, 264 RXD0, SPI_WP, SPI_HOLD, SPI_CLK, SPI_MOSI, SPI_MISO, SPI_CS, 265 I2C_SDA, I2C_SCL, I2S2_IN, I2S3_IN, I2S4_IN, I2S2_OUT, 266 I2S3_OUT, I2S4_OUT, GPIO_B, MDC, MDIO, G2_TXD0, G2_TXD1, 267 G2_TXD2, G2_TXD3, G2_TXEN, G2_TXC, G2_RXD0, G2_RXD1, G2_RXD2, 268 G2_RXD3, G2_RXDV, G2_RXC, NCEB, NWEB, NREB, NDL4, NDL5, NDL6, 269 NDL7, NRB, NCLE, NALE, NDL0, NDL1, NDL2, NDL3, MDI_TP_P0, 270 MDI_TN_P0, MDI_RP_P0, MDI_RN_P0, MDI_TP_P1, MDI_TN_P1, 271 MDI_RP_P1, MDI_RN_P1, MDI_RP_P2, MDI_RN_P2, MDI_TP_P2, 272 MDI_TN_P2, MDI_TP_P3, MDI_TN_P3, MDI_RP_P3, MDI_RN_P3, 273 MDI_RP_P4, MDI_RN_P4, MDI_TP_P4, MDI_TN_P4, PMIC_SCL, 274 PMIC_SDA, SPIC1_CLK, SPIC1_MOSI, SPIC1_MISO, SPIC1_CS, 275 GPIO_D, WATCHDOG, RTS3_N, CTS3_N, TXD3, RXD3, PERST0_N, 276 PERST1_N, WLED_N, EPHY_LED0_N, AUXIN0, AUXIN1, AUXIN2, 277 AUXIN3, TXD4, RXD4, RTS4_N, CST4_N, PWM1, PWM2, PWM3, PWM4, 278 PWM5, PWM6, PWM7, GPIO_E, TOP_5G_CLK, TOP_5G_DATA, 279 WF0_5G_HB0, WF0_5G_HB1, WF0_5G_HB2, WF0_5G_HB3, WF0_5G_HB4, 280 WF0_5G_HB5, WF0_5G_HB6, XO_REQ, TOP_RST_N, SYS_WATCHDOG, 281 EPHY_LED0_N_JTDO, EPHY_LED1_N_JTDI, EPHY_LED2_N_JTMS, 282 EPHY_LED3_N_JTCLK, EPHY_LED4_N_JTRST_N, WF2G_LED_N, 283 WF5G_LED_N, GPIO_9, GPIO_10, GPIO_11, GPIO_12, UART1_TXD, 284 UART1_RXD, UART1_CTS, UART1_RTS, UART2_TXD, UART2_RXD, 285 UART2_CTS, UART2_RTS, SMI_MDC, SMI_MDIO, PCIE_PERESET_N, 286 PWM_0, GPIO_0, GPIO_1, GPIO_2, GPIO_3, GPIO_4, GPIO_5, 287 GPIO_6, GPIO_7, GPIO_8, UART0_TXD, UART0_RXD, TOP_2G_CLK, 288 TOP_2G_DATA, WF0_2G_HB0, WF0_2G_HB1, WF0_2G_HB2, WF0_2G_HB3, 289 WF0_2G_HB4, WF0_2G_HB5, WF0_2G_HB6] 290 291 bias-disable: true 292 293 bias-pull-up: true 294 295 bias-pull-down: true 296 297 input-enable: true 298 299 input-disable: true 300 301 output-enable: true 302 303 output-low: true 304 305 output-high: true 306 307 input-schmitt-enable: true 308 309 input-schmitt-disable: true 310 311 drive-strength: 312 enum: [4, 8, 12, 16] 313 314 slew-rate: 315 enum: [0, 1] 316 317 mediatek,tdsel: 318 description: | 319 An integer describing the steps for output level shifter duty 320 cycle when asserted (high pulse width adjustment). Valid arguments 321 are from 0 to 15. 322 $ref: /schemas/types.yaml#/definitions/uint32 323 324 mediatek,rdsel: 325 description: | 326 An integer describing the steps for input level shifter duty cycle 327 when asserted (high pulse width adjustment). Valid arguments are 328 from 0 to 63. 329 $ref: /schemas/types.yaml#/definitions/uint32 330 331 required: 332 - pins 333 334additionalProperties: false 335 336examples: 337 - | 338 #include <dt-bindings/interrupt-controller/irq.h> 339 #include <dt-bindings/interrupt-controller/arm-gic.h> 340 341 soc { 342 #address-cells = <2>; 343 #size-cells = <2>; 344 345 pio: pinctrl@10211000 { 346 compatible = "mediatek,mt7622-pinctrl"; 347 reg = <0 0x10211000 0 0x1000>; 348 gpio-controller; 349 #gpio-cells = <2>; 350 351 pinctrl_eth_default: eth-pins { 352 mux-mdio { 353 groups = "mdc_mdio"; 354 function = "eth"; 355 drive-strength = <12>; 356 }; 357 358 mux-gmac2 { 359 groups = "rgmii_via_gmac2"; 360 function = "eth"; 361 drive-strength = <12>; 362 }; 363 364 mux-esw { 365 groups = "esw"; 366 function = "eth"; 367 drive-strength = <8>; 368 }; 369 370 conf-mdio { 371 pins = "MDC"; 372 bias-pull-up; 373 }; 374 }; 375 }; 376 }; 377