xref: /freebsd/sys/contrib/device-tree/Bindings/pinctrl/mediatek,mt6797-pinctrl.yaml (revision 2e3507c25e42292b45a5482e116d278f5515d04d) 
1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/pinctrl/mediatek,mt6797-pinctrl.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: Mediatek MT6797 Pin Controller
8
9maintainers:
10  - Sean Wang <sean.wang@kernel.org>
11
12description: |+
13  The MediaTek's MT6797 Pin controller is used to control SoC pins.
14
15properties:
16  compatible:
17    const: mediatek,mt6797-pinctrl
18
19  reg:
20    minItems: 5
21    maxItems: 5
22
23  reg-names:
24    items:
25      - const: gpio
26      - const: iocfgl
27      - const: iocfgb
28      - const: iocfgr
29      - const: iocfgt
30
31  gpio-controller: true
32
33  "#gpio-cells":
34    const: 2
35    description: |
36      Number of cells in GPIO specifier. Since the generic GPIO
37      binding is used, the amount of cells must be specified as 2. See the below
38      mentioned gpio binding representation for description of particular cells.
39
40  interrupt-controller: true
41
42  interrupts:
43    maxItems: 1
44
45  "#interrupt-cells":
46    const: 2
47
48allOf:
49  - $ref: "pinctrl.yaml#"
50
51required:
52  - compatible
53  - reg
54  - reg-names
55  - gpio-controller
56  - "#gpio-cells"
57
58patternProperties:
59  '-[0-9]+$':
60    type: object
61    additionalProperties: false
62    patternProperties:
63      'pins':
64        type: object
65        additionalProperties: false
66        description: |
67          A pinctrl node should contain at least one subnodes representing the
68          pinctrl groups available on the machine. Each subnode will list the
69          pins it needs, and how they should be configured, with regard to muxer
70          configuration, pullups, drive strength, input enable/disable and input
71          schmitt.
72        $ref: "/schemas/pinctrl/pincfg-node.yaml"
73
74        properties:
75          pinmux:
76            description:
77              integer array, represents gpio pin number and mux setting.
78              Supported pin number and mux varies for different SoCs, and are
79              defined as macros in <soc>-pinfunc.h directly.
80
81          bias-disable: true
82
83          bias-pull-up: true
84
85          bias-pull-down: true
86
87          input-enable: true
88
89          input-disable: true
90
91          output-enable: true
92
93          output-low: true
94
95          output-high: true
96
97          input-schmitt-enable: true
98
99          input-schmitt-disable: true
100
101          drive-strength:
102            enum: [2, 4, 8, 12, 16]
103
104          slew-rate:
105            enum: [0, 1]
106
107          mediatek,pull-up-adv:
108            description: |
109              Pull up setings for 2 pull resistors, R0 and R1. User can
110              configure those special pins. Valid arguments are described as below:
111              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
112              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
113              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
114              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
115            $ref: /schemas/types.yaml#/definitions/uint32
116            enum: [0, 1, 2, 3]
117
118          mediatek,pull-down-adv:
119            description: |
120              Pull down settings for 2 pull resistors, R0 and R1. User can
121              configure those special pins. Valid arguments are described as below:
122              0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled.
123              1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled.
124              2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled.
125              3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled.
126            $ref: /schemas/types.yaml#/definitions/uint32
127            enum: [0, 1, 2, 3]
128
129          mediatek,tdsel:
130            description: |
131              An integer describing the steps for output level shifter duty
132              cycle when asserted (high pulse width adjustment). Valid arguments
133              are from 0 to 15.
134            $ref: /schemas/types.yaml#/definitions/uint32
135
136          mediatek,rdsel:
137            description: |
138              An integer describing the steps for input level shifter duty cycle
139              when asserted (high pulse width adjustment). Valid arguments are
140              from 0 to 63.
141            $ref: /schemas/types.yaml#/definitions/uint32
142
143        required:
144          - pinmux
145
146additionalProperties: false
147
148examples:
149  - |
150    #include <dt-bindings/interrupt-controller/irq.h>
151    #include <dt-bindings/interrupt-controller/arm-gic.h>
152    #include <dt-bindings/pinctrl/mt6797-pinfunc.h>
153
154    soc {
155        #address-cells = <2>;
156        #size-cells = <2>;
157
158        pio: pinctrl@10005000 {
159            compatible = "mediatek,mt6797-pinctrl";
160            reg = <0 0x10005000 0 0x1000>,
161                  <0 0x10002000 0 0x400>,
162                  <0 0x10002400 0 0x400>,
163                  <0 0x10002800 0 0x400>,
164                  <0 0x10002C00 0 0x400>;
165            reg-names = "gpio", "iocfgl", "iocfgb", "iocfgr", "iocfgt";
166            gpio-controller;
167            #gpio-cells = <2>;
168
169            uart_pins_a: uart-0 {
170                pins1 {
171                    pinmux = <MT6797_GPIO232__FUNC_URXD1>,
172                            <MT6797_GPIO233__FUNC_UTXD1>;
173                };
174            };
175        };
176    };
177