1* APM X-Gene 15Gbps Multi-purpose PHY nodes 2 3PHY nodes are defined to describe on-chip 15Gbps Multi-purpose PHY. Each 4PHY (pair of lanes) has its own node. 5 6Required properties: 7- compatible : Shall be "apm,xgene-phy". 8- reg : PHY memory resource is the SDS PHY access resource. 9- #phy-cells : Shall be 1 as it expects one argument for setting 10 the mode of the PHY. Possible values are 0 (SATA), 11 1 (SGMII), 2 (PCIe), 3 (USB), and 4 (XFI). 12 13Optional properties: 14- status : Shall be "ok" if enabled or "disabled" if disabled. 15 Default is "ok". 16- clocks : Reference to the clock entry. 17- apm,tx-eye-tuning : Manual control to fine tune the capture of the serial 18 bit lines from the automatic calibrated position. 19 Two set of 3-tuple setting for each (up to 3) 20 supported link speed on the host. Range from 0 to 21 127 in unit of one bit period. Default is 10. 22- apm,tx-eye-direction : Eye tuning manual control direction. 0 means sample 23 data earlier than the nominal sampling point. 1 means 24 sample data later than the nominal sampling point. 25 Two set of 3-tuple setting for each (up to 3) 26 supported link speed on the host. Default is 0. 27- apm,tx-boost-gain : Frequency boost AC (LSB 3-bit) and DC (2-bit) 28 gain control. Two set of 3-tuple setting for each 29 (up to 3) supported link speed on the host. Range is 30 between 0 to 31 in unit of dB. Default is 3. 31- apm,tx-amplitude : Amplitude control. Two set of 3-tuple setting for 32 each (up to 3) supported link speed on the host. 33 Range is between 0 to 199500 in unit of uV. 34 Default is 199500 uV. 35- apm,tx-pre-cursor1 : 1st pre-cursor emphasis taps control. Two set of 36 3-tuple setting for each (up to 3) supported link 37 speed on the host. Range is 0 to 273000 in unit of 38 uV. Default is 0. 39- apm,tx-pre-cursor2 : 2st pre-cursor emphasis taps control. Two set of 40 3-tuple setting for each (up to 3) supported link 41 speed on the host. Range is 0 to 127400 in unit uV. 42 Default is 0x0. 43- apm,tx-post-cursor : Post-cursor emphasis taps control. Two set of 44 3-tuple setting for Gen1, Gen2, and Gen3. Range is 45 between 0 to 0x1f in unit of 18.2mV. Default is 0xf. 46- apm,tx-speed : Tx operating speed. One set of 3-tuple for each 47 supported link speed on the host. 48 0 = 1-2Gbps 49 1 = 2-4Gbps (1st tuple default) 50 2 = 4-8Gbps 51 3 = 8-15Gbps (2nd tuple default) 52 4 = 2.5-4Gbps 53 5 = 4-5Gbps 54 6 = 5-6Gbps 55 7 = 6-16Gbps (3rd tuple default) 56 57NOTE: PHY override parameters are board specific setting. 58 59Example: 60 phy1: phy@1f21a000 { 61 compatible = "apm,xgene-phy"; 62 reg = <0x0 0x1f21a000 0x0 0x100>; 63 #phy-cells = <1>; 64 }; 65 66 phy2: phy@1f22a000 { 67 compatible = "apm,xgene-phy"; 68 reg = <0x0 0x1f22a000 0x0 0x100>; 69 #phy-cells = <1>; 70 }; 71 72 phy3: phy@1f23a000 { 73 compatible = "apm,xgene-phy"; 74 reg = <0x0 0x1f23a000 0x0 0x100>; 75 #phy-cells = <1>; 76 }; 77