1* Rockchip AXI PCIe Root Port Bridge DT description 2 3Required properties: 4- #address-cells: Address representation for root ports, set to <3> 5- #size-cells: Size representation for root ports, set to <2> 6- #interrupt-cells: specifies the number of cells needed to encode an 7 interrupt source. The value must be 1. 8- compatible: Should contain "rockchip,rk3399-pcie" 9- reg: Two register ranges as listed in the reg-names property 10- reg-names: Must include the following names 11 - "axi-base" 12 - "apb-base" 13- clocks: Must contain an entry for each entry in clock-names. 14 See ../clocks/clock-bindings.txt for details. 15- clock-names: Must include the following entries: 16 - "aclk" 17 - "aclk-perf" 18 - "hclk" 19 - "pm" 20- msi-map: Maps a Requester ID to an MSI controller and associated 21 msi-specifier data. See ./pci-msi.txt 22- interrupts: Three interrupt entries must be specified. 23- interrupt-names: Must include the following names 24 - "sys" 25 - "legacy" 26 - "client" 27- resets: Must contain seven entries for each entry in reset-names. 28 See ../reset/reset.txt for details. 29- reset-names: Must include the following names 30 - "core" 31 - "mgmt" 32 - "mgmt-sticky" 33 - "pipe" 34 - "pm" 35 - "aclk" 36 - "pclk" 37- pinctrl-names : The pin control state names 38- pinctrl-0: The "default" pinctrl state 39- #interrupt-cells: specifies the number of cells needed to encode an 40 interrupt source. The value must be 1. 41- interrupt-map-mask and interrupt-map: standard PCI properties 42 43Required properties for legacy PHY model (deprecated): 44- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. 45- phy-names: MUST be "pcie-phy". 46 47Required properties for per-lane PHY model (preferred): 48- phys: Must contain an phandle to a PHY for each entry in phy-names. 49- phy-names: Must include 4 entries for all 4 lanes even if some of 50 them won't be used for your cases. Entries are of the form "pcie-phy-N": 51 where N ranges from 0 to 3. 52 (see example below and you MUST also refer to ../phy/rockchip-pcie-phy.txt 53 for changing the #phy-cells of phy node to support it) 54 55Optional Property: 56- aspm-no-l0s: RC won't support ASPM L0s. This property is needed if 57 using 24MHz OSC for RC's PHY. 58- ep-gpios: contain the entry for pre-reset GPIO 59- num-lanes: number of lanes to use 60- vpcie12v-supply: The phandle to the 12v regulator to use for PCIe. 61- vpcie3v3-supply: The phandle to the 3.3v regulator to use for PCIe. 62- vpcie1v8-supply: The phandle to the 1.8v regulator to use for PCIe. 63- vpcie0v9-supply: The phandle to the 0.9v regulator to use for PCIe. 64 65*Interrupt controller child node* 66The core controller provides a single interrupt for legacy INTx. The PCIe node 67should contain an interrupt controller node as a target for the PCI 68'interrupt-map' property. This node represents the domain at which the four 69INTx interrupts are decoded and routed. 70 71 72Required properties for Interrupt controller child node: 73- interrupt-controller: identifies the node as an interrupt controller 74- #address-cells: specifies the number of cells needed to encode an 75 address. The value must be 0. 76- #interrupt-cells: specifies the number of cells needed to encode an 77 interrupt source. The value must be 1. 78 79Example: 80 81pcie0: pcie@f8000000 { 82 compatible = "rockchip,rk3399-pcie"; 83 #address-cells = <3>; 84 #size-cells = <2>; 85 clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, 86 <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>; 87 clock-names = "aclk", "aclk-perf", 88 "hclk", "pm"; 89 bus-range = <0x0 0x1>; 90 interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH 0>, 91 <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH 0>, 92 <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH 0>; 93 interrupt-names = "sys", "legacy", "client"; 94 assigned-clocks = <&cru SCLK_PCIEPHY_REF>; 95 assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>; 96 assigned-clock-rates = <100000000>; 97 ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; 98 ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x600000 99 0x81000000 0x0 0xfa600000 0x0 0xfa600000 0x0 0x100000>; 100 num-lanes = <4>; 101 msi-map = <0x0 &its 0x0 0x1000>; 102 reg = <0x0 0xf8000000 0x0 0x2000000>, <0x0 0xfd000000 0x0 0x1000000>; 103 reg-names = "axi-base", "apb-base"; 104 resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, 105 <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE> , 106 <&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, <&cru SRST_A_PCIE>; 107 reset-names = "core", "mgmt", "mgmt-sticky", "pipe", 108 "pm", "pclk", "aclk"; 109 /* deprecated legacy PHY model */ 110 phys = <&pcie_phy>; 111 phy-names = "pcie-phy"; 112 pinctrl-names = "default"; 113 pinctrl-0 = <&pcie_clkreq>; 114 #interrupt-cells = <1>; 115 interrupt-map-mask = <0 0 0 7>; 116 interrupt-map = <0 0 0 1 &pcie0_intc 0>, 117 <0 0 0 2 &pcie0_intc 1>, 118 <0 0 0 3 &pcie0_intc 2>, 119 <0 0 0 4 &pcie0_intc 3>; 120 pcie0_intc: interrupt-controller { 121 interrupt-controller; 122 #address-cells = <0>; 123 #interrupt-cells = <1>; 124 }; 125}; 126 127pcie0: pcie@f8000000 { 128 ... 129 130 /* preferred per-lane PHY model */ 131 phys = <&pcie_phy 0>, <&pcie_phy 1>, <&pcie_phy 2>, <&pcie_phy 3>; 132 phy-names = "pcie-phy-0", "pcie-phy-1", "pcie-phy-2", "pcie-phy-3"; 133 134 ... 135}; 136