1Micrel KSZ9021/KSZ9031/KSZ9131 Gigabit Ethernet PHY 2 3Some boards require special tuning values, particularly when it comes 4to clock delays. You can specify clock delay values in the PHY OF 5device node. Deprecated, but still supported, these properties can 6also be added to an Ethernet OF device node. 7 8Note that these settings are applied after any phy-specific fixup from 9phy_fixup_list (see phy_init_hw() from drivers/net/phy/phy_device.c), 10and therefore may overwrite them. 11 12KSZ9021: 13 14 All skew control options are specified in picoseconds. The minimum 15 value is 0, the maximum value is 3000, and it can be specified in 200ps 16 steps, *but* these values are in not fact what you get because this chip's 17 skew values actually increase in 120ps steps, starting from -840ps. The 18 incorrect values came from an error in the original KSZ9021 datasheet 19 before it was corrected in revision 1.2 (Feb 2014), but it is too late to 20 change the driver now because of the many existing device trees that have 21 been created using values that go up in increments of 200. 22 23 The following table shows the actual skew delay you will get for each of the 24 possible devicetree values, and the number that will be programmed into the 25 corresponding pad skew register: 26 27 Device Tree Value Delay Pad Skew Register Value 28 ----------------------------------------------------- 29 0 -840ps 0000 30 200 -720ps 0001 31 400 -600ps 0010 32 600 -480ps 0011 33 800 -360ps 0100 34 1000 -240ps 0101 35 1200 -120ps 0110 36 1400 0ps 0111 37 1600 120ps 1000 38 1800 240ps 1001 39 2000 360ps 1010 40 2200 480ps 1011 41 2400 600ps 1100 42 2600 720ps 1101 43 2800 840ps 1110 44 3000 960ps 1111 45 46 Optional properties: 47 48 - rxc-skew-ps : Skew control of RXC pad 49 - rxdv-skew-ps : Skew control of RX CTL pad 50 - txc-skew-ps : Skew control of TXC pad 51 - txen-skew-ps : Skew control of TX CTL pad 52 - rxd0-skew-ps : Skew control of RX data 0 pad 53 - rxd1-skew-ps : Skew control of RX data 1 pad 54 - rxd2-skew-ps : Skew control of RX data 2 pad 55 - rxd3-skew-ps : Skew control of RX data 3 pad 56 - txd0-skew-ps : Skew control of TX data 0 pad 57 - txd1-skew-ps : Skew control of TX data 1 pad 58 - txd2-skew-ps : Skew control of TX data 2 pad 59 - txd3-skew-ps : Skew control of TX data 3 pad 60 61KSZ9031: 62 63 All skew control options are specified in picoseconds. The minimum 64 value is 0, and the maximum is property-dependent. The increment 65 step is 60ps. The default value is the neutral setting, so setting 66 rxc-skew-ps=<0> actually results in -900 picoseconds adjustment. 67 68 The KSZ9031 hardware supports a range of skew values from negative to 69 positive, where the specific range is property dependent. All values 70 specified in the devicetree are offset by the minimum value so they 71 can be represented as positive integers in the devicetree since it's 72 difficult to represent a negative number in the devictree. 73 74 The following 5-bit values table apply to rxc-skew-ps and txc-skew-ps. 75 76 Pad Skew Value Delay (ps) Devicetree Value 77 ------------------------------------------------------ 78 0_0000 -900ps 0 79 0_0001 -840ps 60 80 0_0010 -780ps 120 81 0_0011 -720ps 180 82 0_0100 -660ps 240 83 0_0101 -600ps 300 84 0_0110 -540ps 360 85 0_0111 -480ps 420 86 0_1000 -420ps 480 87 0_1001 -360ps 540 88 0_1010 -300ps 600 89 0_1011 -240ps 660 90 0_1100 -180ps 720 91 0_1101 -120ps 780 92 0_1110 -60ps 840 93 0_1111 0ps 900 94 1_0000 60ps 960 95 1_0001 120ps 1020 96 1_0010 180ps 1080 97 1_0011 240ps 1140 98 1_0100 300ps 1200 99 1_0101 360ps 1260 100 1_0110 420ps 1320 101 1_0111 480ps 1380 102 1_1000 540ps 1440 103 1_1001 600ps 1500 104 1_1010 660ps 1560 105 1_1011 720ps 1620 106 1_1100 780ps 1680 107 1_1101 840ps 1740 108 1_1110 900ps 1800 109 1_1111 960ps 1860 110 111 The following 4-bit values table apply to the txdX-skew-ps, rxdX-skew-ps 112 data pads, and the rxdv-skew-ps, txen-skew-ps control pads. 113 114 Pad Skew Value Delay (ps) Devicetree Value 115 ------------------------------------------------------ 116 0000 -420ps 0 117 0001 -360ps 60 118 0010 -300ps 120 119 0011 -240ps 180 120 0100 -180ps 240 121 0101 -120ps 300 122 0110 -60ps 360 123 0111 0ps 420 124 1000 60ps 480 125 1001 120ps 540 126 1010 180ps 600 127 1011 240ps 660 128 1100 300ps 720 129 1101 360ps 780 130 1110 420ps 840 131 1111 480ps 900 132 133 Optional properties: 134 135 Maximum value of 1860, default value 900: 136 137 - rxc-skew-ps : Skew control of RX clock pad 138 - txc-skew-ps : Skew control of TX clock pad 139 140 Maximum value of 900, default value 420: 141 142 - rxdv-skew-ps : Skew control of RX CTL pad 143 - txen-skew-ps : Skew control of TX CTL pad 144 - rxd0-skew-ps : Skew control of RX data 0 pad 145 - rxd1-skew-ps : Skew control of RX data 1 pad 146 - rxd2-skew-ps : Skew control of RX data 2 pad 147 - rxd3-skew-ps : Skew control of RX data 3 pad 148 - txd0-skew-ps : Skew control of TX data 0 pad 149 - txd1-skew-ps : Skew control of TX data 1 pad 150 - txd2-skew-ps : Skew control of TX data 2 pad 151 - txd3-skew-ps : Skew control of TX data 3 pad 152 153 - micrel,force-master: 154 Boolean, force phy to master mode. Only set this option if the phy 155 reference clock provided at CLK125_NDO pin is used as MAC reference 156 clock because the clock jitter in slave mode is to high (errata#2). 157 Attention: The link partner must be configurable as slave otherwise 158 no link will be established. 159 160KSZ9131: 161LAN8841: 162 163 All skew control options are specified in picoseconds. The increment 164 step is 100ps. Unlike KSZ9031, the values represent picoseccond delays. 165 A negative value can be assigned as rxc-skew-psec = <(-100)>;. 166 167 Optional properties: 168 169 Range of the value -700 to 2400, default value 0: 170 171 - rxc-skew-psec : Skew control of RX clock pad 172 - txc-skew-psec : Skew control of TX clock pad 173 174 Range of the value -700 to 800, default value 0: 175 176 - rxdv-skew-psec : Skew control of RX CTL pad 177 - txen-skew-psec : Skew control of TX CTL pad 178 - rxd0-skew-psec : Skew control of RX data 0 pad 179 - rxd1-skew-psec : Skew control of RX data 1 pad 180 - rxd2-skew-psec : Skew control of RX data 2 pad 181 - rxd3-skew-psec : Skew control of RX data 3 pad 182 - txd0-skew-psec : Skew control of TX data 0 pad 183 - txd1-skew-psec : Skew control of TX data 1 pad 184 - txd2-skew-psec : Skew control of TX data 2 pad 185 - txd3-skew-psec : Skew control of TX data 3 pad 186 187Examples: 188 189 /* Attach to an Ethernet device with autodetected PHY */ 190 &enet { 191 rxc-skew-ps = <1800>; 192 rxdv-skew-ps = <0>; 193 txc-skew-ps = <1800>; 194 txen-skew-ps = <0>; 195 status = "okay"; 196 }; 197 198 /* Attach to an explicitly-specified PHY */ 199 mdio { 200 phy0: ethernet-phy@0 { 201 rxc-skew-ps = <1800>; 202 rxdv-skew-ps = <0>; 203 txc-skew-ps = <1800>; 204 txen-skew-ps = <0>; 205 reg = <0>; 206 }; 207 }; 208 ethernet@70000 { 209 phy = <&phy0>; 210 phy-mode = "rgmii-id"; 211 }; 212 213References 214 215 Micrel ksz9021rl/rn Data Sheet, Revision 1.2. Dated 2/13/2014. 216 http://www.micrel.com/_PDF/Ethernet/datasheets/ksz9021rl-rn_ds.pdf 217 218 Micrel ksz9031rnx Data Sheet, Revision 2.1. Dated 11/20/2014. 219 http://www.micrel.com/_PDF/Ethernet/datasheets/KSZ9031RNX.pdf 220 221Notes: 222 223 Note that a previous version of the Micrel ksz9021rl/rn Data Sheet 224 was missing extended register 106 (transmit data pad skews), and 225 incorrectly specified the ps per step as 200ps/step instead of 226 120ps/step. The latest update to this document reflects the latest 227 revision of the Micrel specification even though usage in the kernel 228 still reflects that incorrect document. 229