1* MDIO IO device 2 3The MDIO is a bus to which the PHY devices are connected. For each 4device that exists on this bus, a child node should be created. See 5the definition of the PHY node in booting-without-of.txt for an example 6of how to define a PHY. 7 8Required properties: 9 - reg : Offset and length of the register set for the device, and optionally 10 the offset and length of the TBIPA register (TBI PHY address 11 register). If TBIPA register is not specified, the driver will 12 attempt to infer it from the register set specified (your mileage may 13 vary). 14 - compatible : Should define the compatible device type for the 15 mdio. Currently supported strings/devices are: 16 - "fsl,gianfar-tbi" 17 - "fsl,gianfar-mdio" 18 - "fsl,etsec2-tbi" 19 - "fsl,etsec2-mdio" 20 - "fsl,ucc-mdio" 21 - "fsl,fman-mdio" 22 When device_type is "mdio", the following strings are also considered: 23 - "gianfar" 24 - "ucc_geth_phy" 25 26Example: 27 28 mdio@24520 { 29 reg = <24520 20>; 30 compatible = "fsl,gianfar-mdio"; 31 32 ethernet-phy@0 { 33 ...... 34 }; 35 }; 36 37* TBI Internal MDIO bus 38 39As of this writing, every tsec is associated with an internal TBI PHY. 40This PHY is accessed through the local MDIO bus. These buses are defined 41similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi". 42The TBI PHYs underneath them are similar to normal PHYs, but the reg property 43is considered instructive, rather than descriptive. The reg property should 44be chosen so it doesn't interfere with other PHYs on the bus. 45 46* Gianfar-compatible ethernet nodes 47 48Properties: 49 50 - device_type : Should be "network" 51 - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC" 52 - compatible : Should be "gianfar" 53 - reg : Offset and length of the register set for the device 54 - interrupts : For FEC devices, the first interrupt is the device's 55 interrupt. For TSEC and eTSEC devices, the first interrupt is 56 transmit, the second is receive, and the third is error. 57 - phy-handle : See ethernet.txt file in the same directory. 58 - fixed-link : See fixed-link.txt in the same directory. 59 - phy-connection-type : See ethernet.txt file in the same directory. 60 This property is only really needed if the connection is of type 61 "rgmii-id", as all other connection types are detected by hardware. 62 - fsl,magic-packet : If present, indicates that the hardware supports 63 waking up via magic packet. 64 - fsl,wake-on-filer : If present, indicates that the hardware supports 65 waking up by Filer General Purpose Interrupt (FGPI) asserted on the 66 Rx int line. This is an advanced power management capability allowing 67 certain packet types (user) defined by filer rules to wake up the system. 68 - bd-stash : If present, indicates that the hardware supports stashing 69 buffer descriptors in the L2. 70 - rx-stash-len : Denotes the number of bytes of a received buffer to stash 71 in the L2. 72 - rx-stash-idx : Denotes the index of the first byte from the received 73 buffer to stash in the L2. 74 75Example: 76 ethernet@24000 { 77 device_type = "network"; 78 model = "TSEC"; 79 compatible = "gianfar"; 80 reg = <0x24000 0x1000>; 81 local-mac-address = [ 00 E0 0C 00 73 00 ]; 82 interrupts = <29 2 30 2 34 2>; 83 interrupt-parent = <&mpic>; 84 phy-handle = <&phy0> 85 }; 86 87* Gianfar PTP clock nodes 88 89Refer to Documentation/devicetree/bindings/ptp/ptp-qoriq.txt 90